Cisco 1760 and VoIP gateway

Hello NetProf!
I'm repeating my request for help, mabey clearing a few things out.
1. We have a cisco 1760 router running CCME
2. Some connected to it cisco 79xx ip-phones
3. A third party gatekeeper - MikroTik router
4. Every device is logged in the gatekeeper, and every call i settled with the use of it.
5. We have a third party VoIP gateway - MultiTechs MultiVoIP - also registered in the gatekeeper.
6. Now the connections history:
a) when phoning from the gateway to cisco - everything works fine.
b) when phoning fromn cisco to the gateway - the connection failes - it looks like CISCO ISN'T FORWARDING ANY INDENTITY DATA - NO IP ADDRESS, AND H323-ID - GETS TO THE GATEWAY!!!!!
Please help!!
Michal Podoski

Check if there are some known issues documented here:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122relnt/1700/rn1700yj.htm

Similar Messages

Cisco 1760 and E1 to VoIP Gateway

Hello!
Recently we've developed a test VoIP network combined out of a verry differently branched devices. It's working quite well, excluding one part.
The problem occures when trying to call from a CCME Cisco IP phone registered in a gatekeeper to a MultiTechs Multivoip E1/VoIP gateway (which is connected to our PBX). In MvOIPs logs - I can focus Cisco Phone trying to connect using the correct codec, matching gateway prefix - BUT LEAVING NO IP ADDRESS OR H.323 ID. Mabey some ideas???
Network is H.323 based.
Thanks in advance.
Michael

Hi Micheal,
Can your PBX see the digits being passed to it?
Thanks,
Erik

Cisco BRAS 7206 VXR + voip gateways Micronet (part 2)

I'm sorry, I've closed previouse discussion - https://supportforums.cisco.com/message/3075308#3075308
The problem is actual yet.
Micronet voip gateway (SP5002) cant' up pppoe connection to CIsco 7206 vxr, after cisco uptime > 20 days.
I have attached wireshark dump.
IOS: c7200-advipservicesk9-mz.122-33.SRD4.bin
Config:
Current configuration : 12976 bytes
! Last configuration change at 16:14:26 KGST Tue May 18 2010 by tuxper
! NVRAM config last updated at 16:25:21 KGST Tue May 18 2010 by tuxper
version 12.2
service timestamps debug uptime
service timestamps log datetime msec localtime
service password-encryption
service counters max age 5
hostname Router_PPPoE
boot-start-marker
boot system disk2:c7200-advipservicesk9-mz.122-33.SRD4.bin
boot-end-marker
logging buffered 64000
no logging console
enable password 7 071D294A4D101F1F1E140C061C382D74716B
aaa new-model
aaa group server radius PPPOE-RADIUS-SERVER
server-private xxx.x.x.x auth-port 3812 acct-port 3813 key 7 yyyyyyyyy
aaa group server radius ISG-RADIUS-SERVER
server-private xx.x.x.x auth-port 4812 acct-port 4813 key 7 yyyyyyyyyy
aaa group server radius CISCO-AAA-SERVER
server-private xxx.x.x.x auth-port 2812 acct-port 2813 key 7 yyyyyyyyyyyyyy
aaa group server tacacs+ ACCT-TACACS-SERVER
server-private xx.x.x.x key 7 yyyyyyyyyyyyyyyyy
aaa authentication login default local group CISCO-AAA-SERVER
aaa authentication enable default group CISCO-AAA-SERVER enable
aaa authentication ppp PPPoE group PPPOE-RADIUS-SERVER
aaa authorization network PPPoE group PPPOE-RADIUS-SERVER
aaa authorization subscriber-service default local group ISG-RADIUS-SERVER
aaa accounting update periodic 1440
aaa accounting exec default start-stop group CISCO-AAA-SERVER
aaa accounting commands 1 default stop-only group ACCT-TACACS-SERVER
aaa accounting commands 15 default stop-only group ACCT-TACACS-SERVER
aaa accounting network PPPoE start-stop group PPPOE-RADIUS-SERVER
aaa accounting network ISG start-stop group ISG-RADIUS-SERVER
aaa server radius dynamic-author
client xxx.x.x.x server-key 7 yyyyyyyyyyyyy
auth-type all
ignore session-key
ignore server-key
aaa session-id common
clock timezone KGST 6
ip subnet-zero
ip source-route
ip cef
ip name-server xxxxxxxxx
ip name-server xxxxxxxxx
subscriber service password 7 xxxxxxxxxxxxxxxx
redirect server-group REDIR-SERVER
server ip xxx.xxx.xxx.xxx port 9999
multilink bundle-name authenticated
archive
log config
logging enable
notify syslog contenttype plaintext
   hidekeys
path ftp://[email protected]/bras7206-//[email protected]/bras7206-
write-memory
time-period 10080
username tuxper password 7 yyyyyyyyyyyy
username evrey password 7 yyyyyyyyyyyyy
bba-group pppoe global
virtual-template 1
sessions max limit 8000
sessions per-vlan limit 4000
interface Loopback0
ip address xx.xxx.xx.xx 255.255.255.255
interface GigabitEthernet0/1
description 7600_Uplink
ip address yy.yy.yy.yy 255.255.255.252
ip ospf network point-to-point
media-type rj45
speed 1000
duplex full
no negotiation auto
no cdp enable
interface GigabitEthernet0/2
description 7600_Uplink_pppoe_vlan
mtu 9000
no ip address
media-type rj45
speed auto
duplex auto
no negotiation auto
vlan-range dot1q 25 26
pppoe enable group global
   exit-vlan-config
vlan-range dot1q 300 399
pppoe enable group global
exit-vlan-config
vlan-range dot1q 401 461
   pppoe enable group global
exit-vlan-config
vlan-range dot1q 600 620
pppoe enable group global
exit-vlan-config
vlan-id dot1q 20
pppoe enable group global
exit-vlan-config
interface GigabitEthernet0/3
no ip address
shutdown
media-type rj45
speed auto
duplex auto
no negotiation auto
interface Virtual-Template1
description PPPoE
mtu 1492
ip unnumbered Loopback0
ppp authentication chap pap PPPoE
ppp authorization PPPoE
ppp accounting PPPoE
ppp eap refuse
ppp ms-chap refuse
ppp ms-chap-v2 refuse
ppp ipcp dns zzz.zzz.zzz.zzz zzz.zzz.zzz.zzz
router ospf 1
router-id yyy.yy.yy.yy
log-adjacency-changes
summary-address ii.iii.ii.0 255.255.254.0
summary-address ttt.ttt.ttt.0 255.255.255.0
summary-address ttt.ttt.ttt.0 255.255.255.0
summary-address ttt.ttt.ttt.0 255.255.255.0
summary-address ttt.ttt.ttt.0 255.255.254.0
redistribute connected subnets
redistribute static subnets
network uuu.uuu.uuu.uuu 0.0.0.3 area 0
default-information originate
ip classless
no ip http server
no ip http secure-server
!line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
session-timeout 30
exec-timeout 60 0
length 0
international
line vty 5 15
ntp clock-period 17179974
ntp peer vvv.vvv.vvv.vvv
ntp peer vvv.vvvv.vvv.vvv
end
P.S. I'm ready to provide any needed information.

I made config like this:
interface Virtual-Template1
description PPPoE
mtu 1492
ip unnumbered Loopback0
ppp authentication chap pap ms-chap ms-chap-v2 PPPoE
ppp authorization PPPoE
ppp accounting PPPoE
ppp eap refuse
ppp ipcp dns xxx.xx.xx.xx tt.tt.tt.tt
But the problem is actual.
I installed new IOS: c7200-advipservicesk9-mz.122-33.SRE1.bin
But 21 days is over, and I have the same problem.
I don't understand anything.

Router 2901 as VoIP gateway

Hello,
I'm trying to configure a CISCO 2901 Integrated Services Router with a Module VWIC3-1MFT-T1/E1 as a VoIP gateway.
I'd like to know if is it possible, and if there is a especific document in CISCO documentation explaining it.
I have the following escenary:
Inbound calls:
PSTN (ISDN) --> CISCO 2901 --> Asterisk (SIP PBX)
Outbound calls
Asterisk(SIP PBX) --> CISCO 2901 --> PSTN (ISDN)
I have found some documents which explains how to configure a SIP Trunk with registration
http://www.cisco.com/en/US/docs/ios-xml/ios/voice/cube_sipsip/configuration/xe-3s/asr1000/voi-sip-trunk-reg.html
And how to configure the VWIC3 module
http://www.cisco.com/en/US/docs/routers/access/interfaces/software/feature/guide/vd-t1e1_vwic3.html
I'm very new with CISCO and I don't know how to route calls from the module to the Ethernet interface, and if I need to do anything else.
Thanks in advance!
David Pinedo
Presence Technology

For ISDN you need to configure your T1/E1, plenty of material and also references/examples on CSC, a quick search will provide some basic config
http://www.cisco.com/en/US/partner/docs/voice_ip_comm/cucme/admin/configuration/guide/cmebasic.html
Search pri-group timeslots to get more examples.
Then you'll need to configure dial-peers for in/out calls, search cisco.com for dial-peer configuration and you'll get all the info you need on how to configure them.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

Clear Channel Codec between Cisco GW and Patton Smartnode

Hi,
i have to establish an H.323 connection between an Cisco 3745 and an Patton
Smartnode 1200 with clear-channel codec to support ISDN-Data over VoIP.
PC with ISDN-Card---S0/PattonGW----H.323----3745/E1----PSTN
Software versions:
Cisco: SPServices 12.4(5a)
Patton SN1200: R3.20 2006-03-30 H323
The call establishment is sucessfull but i am not able pass any Data over
ISDN. Does anyone got this working?
Any help is welcome.
Regards,
Robert
Below are some Konfig sniplets:
Cisco:
controller E1 0/1/0
pri-group timeslots 1-31
interface Serial0/1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
no cdp enable
dial-peer voice 10 pots
description ----- Towards PSTN -----
answer-address <removed>
destination-pattern 0T
progress_ind setup enable 3
fax rate disable
direct-inward-dial
port 0/1/0:15
dial-peer voice 473997246 voip
description ----- towards Patton GW -----
destination-pattern <removed>
progress_ind setup enable 3
modem passthrough nse codec g711alaw
session target ipv4:192.168.1.28
codec clear-channel bytes 80
ip qos dscp cs5 media
no vad
dial-peer voice 473997247 voip
description ----- Incoming Dial-Peer -----
modem passthrough nse codec g711alaw
incoming called-number <removed>
codec clear-channel bytes 80
ip qos dscp cs5 media
no vad
Patton:
profile voip VOIP
codec 1 transparent-cisco rx-length 20 tx-length 20
no high-pass-filter
no post-filter
no dtmf-relay
no dtmf-mute-encoder
context ip router
rtp-port-range 16384 32767
context cs switch
no digit-collection timeout
no address-completion timeout
interface h323 IF_H323
bind gateway GW_H323
route call dest-interface IF_S0_01
remote 192.168.254.30 1720
itc rx transparent
use profile voip VOIP
interface isdn IF_S0_01
route call dest-interface IF_H323
use profile tone-set Europe
no call-waiting
gateway h323 GW_H323
faststart
early-h245
h235-security version v2
no h235-security q931-auth-int
bind interface IF_IP_LAN router
no shutdown
use profile voip VOIP
port bri 0 1
clock auto
encapsulation q921
q921
protocol pmp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side net
encapsulation cc-isdn
bind interface IF_S0_01 switch

The SIP Media Inactivity Timer feature enables Cisco gateways to monitor and disconnect VoIP calls if no Real-Time Control Protocol (RTCP) packets are received within a configurable time period.
When RTCP reports are not received by a Cisco gateway, the SIP Media Inactivity Timer feature releases the hung session and its network resources in an orderly manner. These network resources include the gateway digital signal processor (DSP) and time-division multiplexing (TDM) channel resources that are utilized by the hung sessions. Because call signaling is sent to tear down the call, any stateful SIP proxies involved in the call are also notified to clear the state that they have associated with the hung session. The call is also cleared back through the TDM port so that any attached TDM switching equipment also clears its resources.
http://www.cisco.com/en/US/products/ps6441/prod_troubleshooting_guide09186a00801fa207.html#wp2077496

How to set up VLAN for DATA and VOIP on SRW248G4P switch?

Hi guys,
I am totally new and was given this task to complete. I really really need help.
We are using one network 192.168.1.0
Shared with data and voip.
CISCO C870, 5 switches LINKSYS SRW248G4P .
The email wrote:-
On the Linksys switch;
- create two different VLANs one for voice and one for data.
- put a firewall between the two VLANs (between voice and data) and only enable certain ports to flow to voice network (inbound tcp 8443 and ssh )
What should i do guys? I really need a dumb guide now.
I know its simple for you guys but i am not a smart IT fella. Whats the step by step?

If the switch is new or you have support on this, then you might try calling the support center. Here is a link:
https://www.myciscocommunity.com/community/smallbizsupport
On the right hand side you can find links to the support center.
Here is a link to the guide:
http://www.cisco.com/en/US/products/ps9967/prod_maintenance_guides_list.html
@ the bottom of this link you can find your switch model, you want the larger of the two. In this guide it shows you how to create a second vlan.
Will your router be the firewall between the two?
Kindest regards,
Andrew Lissitz

Cisco wireless and Apple Mac woes

Hello all,
I've been working with Cisco wireless and WLC's for a couple of years now but the recent onslaught of Apple Mac's is giving me heart burn. I've seen this at numerous sites now and need to throw it to eht community for guidance.
Basically we have had a number of instances where the Macs just fall off the wifi. Sometimes it's when they wake from sleep and other times when roaming between AP's (1131s with same SSID's). Our standard install is WPA2 and per ap local authentication. PC's work fine and never an issue.
We have completed a survey with a spectrum analyser and no RF interefence is present nor errors on the radio interface.
Questions:
- Is there a preferred Cisco config/setup for Mac's to work reliably? I've heard loads of rumors but nothing concrete and nor can I find anything specific.
- Should I be setting up WDS in case there is an authenticating issue.
- For those who are Mac gurus and happen to be reading. What Mac options we should look at?
This has all come to a head because the clients IT company who recommended the Macs (different from us doing the network infrastructure) are insisting that the problem is Cisco incompatibility and that we should rip out the Cisco kit and install airports (what tha!!!).
Thanks in advance for any pointers.
For those who like a config here it is .... Vanilla stuff really
Building configuration...
Current configuration : 2236 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP4
no logging console
enable secret xxxxxxxxxxxxxxxxx
no aaa new-model
dot11 syslog
dot11 ssid Home
   vlan 1
   authentication open
   authentication key-management wpa
   guest-mode
   mbssid guest-mode
   wpa-psk ascii xxxxxxxxxxxx
dot11 ssid avnet
   vlan 2
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii xxxxxxxxxxxxxxxx
username abcd password 1234
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers tkip
encryption vlan 2 mode ciphers tkip
ssid Home
mbssid
speed basic-1.0 basic-2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2412
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 80 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 192.168.10.54 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
no ip http server
no ip http secure-server
bridge 1 route ip
line con 0
line vty 0 4
login local
end

Yeah!! even i have come across multiple issue with MAC and Cisco.. these are the below settings which i normally do on the cisco gears and most of the times this solved the issue..
on the IOS AP disable Aironet Extentions and set the poer local and ofdm to max
no dot11 extension aironet
power local cck max
power local ofdm max
end
On the WLC, disable Aironet IE..
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Urgent!!! Cisco ACE and asymetric routing assistance needed

I am wondering if someone can give me pointers on the cisco ACE
and asymetric routes. I've attached the diagram:
-Cisco IOS IP address is 192.168.15.4/24 and 4.1.1.4/24
-Firewall External interface is 192.168.15.1/24,
-Firewall Internal interface is 192.168.192.1/24,
-F5_BigIP External interface is 192.168.192.4/24,
-F5_BigIP Internal interface is 192.168.196.1/24 and 192.168.197.1/24,
-host_y has IP addresses of 192.168.196.10/24 and 192.168.197.10/24,
-Checkpoint has static route for 192.168.196.0/24 and 192.168.197.0/24
pointing to the F5_BigIP,
-host_y is dual-home to both VLAN_A and VLAN_B with the default
gateway on host_y pointing to VLAN_A which is 192.168.196.1,
-host_x CAN ssh/telnet/http/https to both of host_y IP addresses
of 192.168.196.10 and 192.168.197.10.
In other words, from host_x, when I try to connect to host_y
via IP address of 192.168.197.10, the traffics will go through VLAN_B
but the return traffics will go through VLAN_A. Everything
is working perfectly for me so far.
Now customer just replaces the F5_BigIP with Cisco ACE. Now,
I could not get it to work with Asymetric route with Cisco ACE. In
other words, from host_x, I can no longer ssh or telnet to host_y
via IP address of 192.168.197.10.
Anyone knows how to get asymetric route to work on Cisco ACE?
Thanks in advance.

That won't work because ACE uses the vlan id to distinguish between flows.
So when the response comes back on a different vlan, ACE can't find the flow it belongs to and it drops it.
Even if we could force it to accept the packet, ACE would then try to create a new flow for this packet and it will collide with the flow already existing on the frontend.
You would need to force your host to respond on the same vlan the traffic came in.
This could be done with client nat on ACE using different nat pool.
Gilles.

Can I add VOIP Gateway SPA2100-SU to the DMZ of Router BEFSR41 Ver 4 ?

I am having multiple problems with dropped calls; need to reboot my LinkSys VOIP Gateway and so on, and my VOIP provider has suggested the following: "Add your Gateway (the physical device I guess) to the DMZ of your router." We are trying to tell the Router to give this VOIP Gateway, which gets its IP address via DHCP from the router, to essentially give this Gateway carte blanche to any port or destination it wants. I have NO idea how to do this on the BEFSR41, which is a CA model with Version 4 appended to its model number ? Can anyone send me how to advice ? - Mike BRYAN Ottawa Canada PM me for my email.
(Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 01-22-2008 02:54 PM

First thing is to assign a static IP on the WAN / Internet side of your SPA-2100 so that you can set that IP to the DMZ of the BEFSR41. If you are not sure how to assign a static IP address on the spa2100 or how to open the web interface of the spa2100 and befsr41, then you better refer to the KB articles from www.linksys.com/kb. Just type in something like spa2100 or befsr41.
By the way, you may also enable NAT mapping and NAT Keep alive in your spa2100 aside from opening / forwarding ports in the befsr41 (check out Answer ID 5242). Lastly, enabling Send Resp To Src Port in the spa2100 is another option to try (this is under Voice > SIP > NAT Support Parameters).
It really requires much reading for us beginners to fully understand these devices. I am happy that I learned how to use the KBase site of Linksys since it gives me useful info about their products.

Cisco 1760 with shdsl

I have a cisco 1760 router with one adsl wic and one shdsl wic (wic 1 shdsl v3).The router has detected the adsl wic but not the shdsl.I am using the following software:c1700-y7-mz.123-4.XG5.bin.I have tried several ios and used feature navigator to find ios but neither works.Here is output of sh version
Can somedy help ?

Already replied in WAN forum, please do not open duplicate threads.

VLANs and VoIP on the same port

Hello, we want to move our VoIP system on its own vlan. We currently have everything on one big broadcast domain. I have been doing some reading and have head about Voice Vlans and switchport modes. All of our computers are connected to our ip phones so they are on the same physical line. The phones are Aastra 480i and they run on a sphericall phone system. The phones can tag the phone data with 802.1p/q. If im using static port based vlans how would i configure the ports to accepts these 2 diffrent vlans?

Hi Friends,
I have tried many a times with Avaya Ip phones and Cisco swiches and it works fine.
Actually what I think CDP is used for inline power negotation so if you dont have Cisco switches you have to use external power supply. Also now a days switches are coming which internal power supply which supoprt IEEE standard so if we have those switches we can use other vendors ip phones without external power supply.
Anoher thing I will always recommend not to configure trunk especially cause tht may result in pc getting DHCP ip adress later. I have experienced many a times this situation. When you configure switchport voice vlan command on the switch it automatically forms an internal trunk which is not displayed on the switch but internally it works.
Right now I was not able to find one cisoc doc which especially says no need for trunk if you configure switchport voice vlan command on switch.
So just 2 commands
switchport voice vlan
switchport access vlan
Works perfectly fine.
HTH
Ankur

Cisco 1760 router stays in rommon modus

I am having problems with a cisco 1760 router. When I turn the router on I am getting stuck in rommon mode. When I enter the command: "boot flash:c1700-sv8y7-mz.123-11.T3.bin" , the router will boot the ios image. But when i turn the router off and on, it will return to rommon mode. I have tried the following commands in rommon mode:
rommon 1 > confreg 0x2102
rommon 2 > reset
or
rommon 1 > confreg 0x142
rommon 2 > reset
without results. I get the following errors:
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
Bad checksum on cookie structure, resorting to backup copy
Correcting primary cookie from backup
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number:      0x0
open: failed to find and/or load the bootloader: "flash:music-on-hold.au"
loadprog: error - on file open
boot: cannot load "c1700-sv8y7-mz.123-11.T3.bin"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number:      0x0
boot: cannot load "flash:"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number:      0x0
boot: cannot load "flash:"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
rommon 1 >
rommon 1 >
Thanks,
Pieter

I would recommend posting in the netpro forums about this.
http://www.cisco.com/go/netpro
This site is for the Cisco Small Business Pro routers.
For your problem though, you might try looking at your boot system command in your running config to make sure that it is accurate.

SPA112 and IOS gateway

Hi,
I have installed several ATA112 using callmanager.
But is it possible to use a Cisco voice gateway (29xx) without CME?
I mean the SPA112 doesn't register but just send SIP messages to the 29xx gateway and this gateway has a PRI line.
Would this work?
Thanks
JH

JH,
Have you figure it out?
Please advise
Chris

Can I have Cube and Vxml Gateway configured on same Router box ?

Hi
I have one router Model #3900 Series Can I have Cube and Vxml Gateway configured on same router ? If yes, Can any one help me with sample configuration for same.
Thanks and Regards
Anil Kumar.

Here is an example of CVP hardware/software compatibility for CVP 10.0, similar doc exists for each version of CVP.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/customer_voice_portal/cvp10_0/reference/guide/CCVP_BK_1ECCDBC7_00_1001-bom/CCVP_BK_1ECCDBC7_00_1001-bom_chapter_00.html

Cisco 831 and "Can't get video from the camera."

I'm running a Cisco 831 router with ios 12.4(5a) installed. Every time I try to initiate a video chat with a computer going through the router, I get the "Can't get video..." error. It works fine with computers on my internal network and if I bypass the Cisco router and plug straight into my Cable modem.
I've covered every conceivable TCP/UDP port being open (per numerous pages re: port 5060, 5190, etc.) and have even gone as far as testing with "permit UDP any any" and "permit TCP any any" at the top of the rules. No luck.
I've been reading about the possibly needing to "unbind" SIP (port 5060). Is this something that a Cisco 831 router would require? The router doesn't seem to respond to any of the documented Cisco command re: VoIP and does not have any phone support that I'm aware of.
If anyone has any info that can help me get his up-and-running, I'd be much obliged.
Thanks,
Matheau

Hi Kcritchie,
It will most likely look like that. But in this case it should be on the UDP protocol.
The link looks useful (it takes a scroll down to see it for others looking)
If I do nat bindlist in my Alcatel I get this
Last login: Thu Jun 29 12:36:20 on console
Welcome to Darwin!
Ralph-G4:~ Ralph$ telnet 10.0.0.138
Trying 10.0.0.138...
Connected to speedtouch.johnshome.
Escape character is '^]'.
Username :
(Pic line drawing edited out here )
=>nat bindlist
Application Proto Port
ESP esp 1
FTP tcp 21
GRE gre 1
H323 tcp 1720
IKE udp 500
ILS tcp 389
ILS tcp 1002
IP6TO4 6to4 1
IRC tcp 6660-6670
JABBER tcp 5222
JABBER tcp 15222
PPTP tcp 1723
RAUDIO(PNA) tcp 7070
RTSP tcp 554
=>
On my device this is because the SIP binding on UDP port 5060 is unbound.
2:30 PM Thursday; June 29, 2006

Cisco 1760 and VoIP gateway

Similar Messages

Maybe you are looking for