Cisco 1760 router will not recognize wic1-dsu-t1-v2 card in slots 3 or 4
My 1760 router will not recognize a wic1-dsu-t1-v2 card in slots 3 or 4. They only work in slots 1 & 2. Never saw this before where the same card would not work in different slots.
Need assistance.
Thanks,
Ron
Router#show version
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-IPBASE-M), Version 12.3(6c), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 20-Jul-04 07:00 by kellythw
Image text-base: 0x80008120, data-base: 0x80C74650
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
Router uptime is 20 minutes
System returned to ROM by power-on
System image file is "flash:c1700-ipbase-mz.123-6c.bin"
cisco 1760 (MPC860P) processor (revision 0x500) with 55598K/9938K bytes of memory.
Processor board ID FOC0849230K (3846615071), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
WIC T1-DSU
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router#show flash
System flash directory:
File Length Name/status
1 7517112 c1700-ipbase-mz.123-6c.bin
[7517176 bytes used, 25775112 available, 33292288 total]
32768K bytes of processor board System flash (Read/Write)
Router#show diag
Slot 0:
C1760 1FE VE 4SLOT DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 5.0
PCB Serial Number : FOC0849230K
Part Number : 73-7167-05
Board Revision : B0
Fab Version : 04
Product (FRU) Number : CISCO1760
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 16 41 05 00 C1 8B 46 4F 43 30 38 34
0x10: 39 32 33 30 4B 82 49 1B FF 05 42 42 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC/VIC Slot 0:
FT1 4351
Daughter card-Version 4 TLV Cookie Format
Hardware Revision : 1.1
PCB Serial Number : FOC09053XP1
Part Number : 73-8346-04
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0-0
Product (FRU) Number : WIC-1DSU-T1-V2
Top Assy. Part Number : 800-22193-02
CLEI Code : IP4I380GAB
WIC/VIC Slot 1:
FT1 4351
Daughter card-Version 4 TLV Cookie Format
Hardware Revision : 1.2
PCB Serial Number : FOC10073JND
Part Number : 73-8346-05
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0-0
Product (FRU) Number : WIC-1DSU-T1-V2
Top Assy. Part Number : 800-22193-03
CLEI Code : IPUIAPRRAA
Hi Ron,
Slots 3 & 4 are for VICs only.
Have a look at the Location/ Function table here:
http://www.cisco.com/en/US/products/hw/routers/ps221/products_tech_note09186a00800c3399.shtml
cheers,
Seb.
Similar Messages
-
Wireless router will not recognize password
My wirelss router will not recognize the password on the router. Would like to change it to something wowrkable.
https://customer.comcast.com/help-and-support/Wireless-Gateway
http://customer.comcast.com/help-and-support/internet/wireless-gateway-username-and-password/
http://customer.comcast.com/help-and-support/internet/securing-wireless-gateway-network/
http://customer.comcast.com/help-and-support/internet/broadband-gateways-userguides
http://media2.comcast.net/anon.comcastonline2/support/userguides/Wireless_Gateway_User_Guide_030811.... -
My mac will not recognize my kodak 8gb memory card what do i do
my mac will not recognize my kodak 8gb memory card what do i do?
Follow up to Linc's post above: Are you using the SD card reader in the Mac or an external card reader?
Stedman -
My g4 will not recognize my USB SD flash card
I am trying to use my USB SD flash card to open some pictures and I get a message that my with 10.4.11 G4 will not recognize the card. I used it yesterday.
What USB SuperDrive...?
For the Apple USB SuperDrive, see > Troubleshooting the slot-loading SuperDrive or take it to your local AASP and have it checked out. -
I recently purchased a MacBook Air and an Airport Time Capsule. The Time Capsule does not recognize my old iPhone, my old iPod Touch and my new MacBook Air. The old AirPort Extreme works perfectly on the network, so I know it's not my internet. It also recognizes all my devices by name and hooks them up to the internet. Is the Time Capsule broken or is there some secret trick I need to know to get it to work?
Ellen H.Check the Ethernet connection to the AirPort Express. Make sure that the Ethernet connection from the Comcast modem is connected to the WAN port on the back of the AirPort Express. The WAN port is the one with the circle of dots shown over the port.
It sounds like you are connected to the Ethernet LAN port. -
Win7 will not recognize my ATI 5870 video card on Bootcamp
HI,
I have a MAC pro 1.1 and I have an ATI 5870 video card. On OS 10.9.3 the mac sees the video card just fine, but when I use Bootcamp and run Win7 I can’t get the card to work properly. I tried to go to ATI and download the drivers but I keep "no such card found on your device" error from ATI or I can’t fine the correct drivers. When I run Dxdiag the video area shows me no video card information aside from this card is working properly. Can anyone assist me please?
Thank s in advance.A Mac Pro 1,1 technically can't run Mac OS X 10.9 without a hack. Thus it is unlikely the Boot Camp drivers Apple included for it would recognize anything on it newer than is supported. You could try using another Virtualization engine that speaks to all graphics chips with their own drivers:
https://discussions.apple.com/docs/DOC-2741 -
Win7 will not recognize my ATI 5870 video card in Bootcamp
HI,
I have a MAC pro 1.1 and I have an ATI 5870 video card. On OS 10.9.3 the mac sees the video card just fine, but when I use Bootcamp and run Win7 I can’t get the card to work properly. I tried to go to ATI and download the drivers but I keep "no such card found on your device" error from ATI or I can’t fine the correct drivers. When I run Dxdiag the video area shows me no video card information aside from this card is working properly. Can anyone assist me please?
Thank s in advance.have you tried to download the correct bootcamp driver zip for your mac and manually install the latests Radeon amd driver from that?
Apple - Support - Downloads -
It got A new router today and wanted to turn on apple tv but my remote app on iPad and iPhone will not recognize apple tv. Btw- I do not have apple tv remote.
It reboots it but unplugging can also rectify communication issues like this. A restore would be the next step.
-
My HP Officejet Pro 8600 Plus printer will not recognize my wireless router passwrd
My printer was working fine but when I turned it on today it wouldn't connect to my wireless router. I try inputing the correct password and the printer gives me this message......"the WPA security passphrase configured on your HP printer does not match your wireless router setting" .
I have entered the password several times and I know what I have entered is correctHi @Southglen,
Welcome to the HP Forums!
I noticed that your HP Officejet Pro 8600 Plus printer will not recognize your wireless router password. I am sorry to hear this, but happy to help!
I would recommend to go through this guide, How to Find the WEP or WPA Key or Password for Your Wireless Network, just to double-check your wireless password, in case it might have changed.
I would also suggest a hard reset, by going to this post How to perform a Hard Reset, by @Rich1.
After those two steps, I would suggest a firmware update, Getting Printer Updates for HP Officejet Pro 8600 (N911), Officejet 6600 (H711) and Officejet 6700 P....
Let's start with these steps, and we will go from there!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping! -
Printer will not recognize wireless router
Printer was previsously working fine. Moved and network changed via AT&T Uverse and the HP 5530 printer will not recognize the wireless router information. I have uninstalled the printer from my ASUS laptop and tried to re-install to no avail. The cd that came with the printer woould not lnstall the printer again. The printer is less than a year old. I have no idea what is going on. Can you help me fix this problem?
This question was solved.
View Solution.Replacing your wireless router try here.
http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired! -
I have changed to AT&T U-verse, which has a new modem and router combined. Safari 5.1.10 will not recognize the wifi signal, but Foxfire will. What settings do I need to change on Safari?
Hello SalsburgD
The first thing I would check is to make sure that the router is using the recommended settings to get online. Another troubleshooting step is to create a new Network Location and then join your network to see if that changes things.
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/HT4199
Using network locations (Mac OS X v10.6 and later)
http://support.apple.com/kb/ht5289
Regards,
-Norm G. -
My husband's 3GS IPhone will not recognize a Wi-Fi connection at home or work. We have tried turning it on/off as well as turning airplane mode to on while turning it off then back on again. My 3GS IPhone is working fine with our router at home. Please advise what our next step should be. Thank you for taking the time to read this post!!
Just to double check you tried eveyrthing take a look at this link http://support.apple.com/kb/TS1398 .
Can also try powering off the home router, then the phone, and then power up the router wait for the signal and then power up the phone and see if he can connect. -
C2921 router will not bring up fibre SFP
c2921 router will not bring up fibre SFP
I can't get two cisco 2921 routers to talk to each other
the setup works find in my testbed with a rj45 cross over cable between them or even with a WANEM cloud emulator(free tool).
after migrating from CU to fibre they won't to talk to each other anymore. worse, both refuse to bring up their wan side fibre SFP.
the "media-type" sub i/f command was used to change to SFP from RJ45
after that, the EN SFP light appears on both routers, but no link light
sh int gi 0/1
GigabitEthernet0/1 is down, line protocol is down
Hardware is CN Gigabit Ethernet, address is xxx(bia xxx)
Description: ** TEST LINK
Internet address is 1.1.1.2/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is SX
the two routers are in different buildings and must pass through a middle building(#2)
B1 - 200m -- B2 -- 900m -- b3
R1 (in building 1) is 200m from building 2
R2 (in building 3) is 900M from building 2
R1 has a MM SFP in Gi 0/1
R2 has a SM SFP in Gi 0/1 as the distance is too far for MM
in building two we have used both a SM to MM media converter
and a layer two switch with SM and MM SFP,
both show similar results
R1(MM sfp) --MM cable-- (MM sfp) switch (SM sfp) --SM cable--(SM sfp)R2
on the switch( in Bld 2), we see links lights coming out of the two routers, for both SM and MM links, this is good and expected. no traffic is seen though
on either router, no link light is seen and both interfaces are down down. shut, no shut, does not bring them up
we have tried different SFP and cables, still no change
one google search mentions an undocumented ciso command to ignore incompatibale SFP, but that does not work in IOS 15
if we add a 3750 switch to the routers Gi 0/1 WAN side as a media converter, we get success.
each switch has two sfp, one Cu and the other MM or SM fibre .
the router "media-type" sub i/f command was used to change to RJ45 from SFP, after that, the SFP EN lights goes out(as expected) on both routers,
R1(CU)-(CU)3750(MM sfp) --MMcable-- (MM sfp) switch (SM sfp) --SMcable--(SM sfp)-(SM sfp)3750(CU)R2
why does this work and the connection on the rtr does not
sh int gi 0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is xxx(bia xxx)
Description: ** TEST LINK
Internet address is 1.1.1.2/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is RJ45
this test is not practical in the deployed field and far too expensive
i am looking for a solution and want to know why the SFPs do not work in the routers
i tried two different MM SFP. neither one worked, though from SH INV, one can't tell them apart. on the CISCO site only this one is supported
glc-sx-mm, the SFP-GE-s is not supported on the 29xx rtr but is on the 3750 switch (;
================
%added SFP-GE-s SFP, the SFP-GE-s is not supported on the 29xx rtr but is on the 3750 switch
sh inv
NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V03 , SN: xxxxSFP-GE-s
NAME: "1000BASE-SX SFP", DESCR: "1000BASE-SX SFP"
PID: FTLF8519P2BNL-C6B , VID: B , SN: xxxx
%============
%remove SFP and added glc-sx-mm SFP, this is the supported MM SFPO for the 29xx rtr
sh inv
NAME: "1000BASE-SX SFP", DESCR: "1000BASE-SX SFP"
PID: SFBR-5766PZ-CS1 , VID: , SN: xxx
============
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID xxx
9 FastEthernet interfaces
3 Gigabit Ethernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
500472K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2921/K9 xxx
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc None None None
data None None None
Configuration register is 0x2102Problem solved.
MAJOR untested bug in IOS 15.0(1)M3 which was the default image when we bought the devices
*** AVOID IOS 15.0 series ***
there are several bugs related to SFPs like:
does does recognize SFP
des not recognize some EHWIC cards such as, but not limited to EHWIC 1GE-SFP-CU
CSCtj35792
c3900 : gigE SFP should switch to 1000/FD if other side has no nego
Externally found severe (Sev2) bug: M-More
CSCth28824
c3945 GE shows DOWN/DOWN as compare to SFP
Externally found moderate (Sev3) bug: R-Resolved
They were fixed in 15.0(1)M4 or later
You can check the caveats for this IOS Release 15.0M:
http://www.cisco.com/en/US/docs/ios/15_0/release/notes/150MCAVS.html -
MacBook Pro i5 with retina will not recognize WD Passport even though I successfully used it to transfer programs and files from my older MacBook ten days ago. It receives power from the USB, but when using Time Machine I receive the message that there is not an external device connected.
If the modem is also a router, either use the modem in bridge and run pppoe client on the TC.. that is assuming ADSL or similar eg vdsl. If it is cable service.. and the modem is a router, then bridge the TC.. go to internet page and select connect by ethernet and below that set connection sharing to bridge.
Please tell us more about the modem if the above gives you issues. -
Cisco 1760 router stays in rommon modus
I am having problems with a cisco 1760 router. When I turn the router on I am getting stuck in rommon mode. When I enter the command: "boot flash:c1700-sv8y7-mz.123-11.T3.bin" , the router will boot the ios image. But when i turn the router off and on, it will return to rommon mode. I have tried the following commands in rommon mode:
rommon 1 > confreg 0x2102
rommon 2 > reset
or
rommon 1 > confreg 0x142
rommon 2 > reset
without results. I get the following errors:
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
Bad checksum on cookie structure, resorting to backup copy
Correcting primary cookie from backup
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number: 0x0
open: failed to find and/or load the bootloader: "flash:music-on-hold.au"
loadprog: error - on file open
boot: cannot load "c1700-sv8y7-mz.123-11.T3.bin"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number: 0x0
boot: cannot load "flash:"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number: 0x0
boot: cannot load "flash:"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
rommon 1 >
rommon 1 >
Thanks,
PieterI would recommend posting in the netpro forums about this.
http://www.cisco.com/go/netpro
This site is for the Cisco Small Business Pro routers.
For your problem though, you might try looking at your boot system command in your running config to make sure that it is accurate.
Maybe you are looking for
-
Auto update of contact groups in Address Book when created on iphone?
So, I'm OK with how to work with two phones on the one itunes account, with regard to contacts and calendars, but can I get Address Book to automatically add any new contacts created on each phone to the correct contact group?
-
PI 7.1 upgrade related issue (With removeContexts node function)
Hi all, We have upgrade from PI 7.0 to 7.1, there was no changes done to the maps...but when we execute the old maps it give no value in the queue error: (this occurs during run time)... But when I test the payload it executes fine...I have found and
-
An error occured in communication with the BW server.--urgent
Hi all, Can anybody help me. i got 1 issue like ,when iam trying to executing query, iam getting the error pop up screen like 'An error occured in communication with BW server' 'Due to this ,the Connection Has To be Closed'. Detailed Description: 1
-
-
Faulty error message in Eclipse
Hi, I'm using Eclipse (version 3.0.2) together with the N. Takezoe's FacesIDE plugin (version 0.1.5). Unfortunately - for code lines like <h:outputText value="#{msg[client.rc]}" styleClass="message"/> - I always get (in Eclipse's "Problems View" wind