Cisco 1760 with shdsl

I have a cisco 1760 router with one adsl wic and one shdsl wic (wic 1 shdsl v3).The router has detected the adsl wic but not the shdsl.I am using the following software:c1700-y7-mz.123-4.XG5.bin.I have tried several ios and used feature navigator to find ios but neither works.Here is output of sh version
Can somedy help ?

Already replied in WAN forum, please do not open duplicate threads.

Similar Messages

CISCO 1841 with SHDSL Problem?

Hello,
I´am new in cisco WIC configuration. I have a CISCO 1841 with a interface: 1SHDSL v3 and i want to connect to my ISP over a PPoE encapsulation.
I just make the new interface connection in SDM, but the synchronism with the ISP not work. The ISP tell me that VPI/VCI is 0.35 and the annex is the A.
I live in the Europe, but i think that the annex A is for POTS lines and Annex B for ISDN, right?? My line is ADSL Analog.
My startup-configuration is that:
Router#show run
Building configuration...
Current configuration : 2974 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
dot11 syslog
ip source-route
ip cef
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-2879799878
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2879799878
revocation-check none
rsakeypair TP-self-signed-2879799878
crypto pki certificate chain TP-self-signed-2879799878
certificate self-signed 01
3082023E 308201A7 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32383739 37393938 3738301E 170D3131 30343233 32303532
33345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 38373937
39393837 3830819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100BE34 379A4D5D 1DA98B67 708AF8D4 221F1BE5 C5947EEA FF931EF4 37AD8A2C
C786C8D9 88E97474 D32FE0F0 10C048B9 6F5DA580 55241E61 9B0D849A D9E7182A
04D6C8E0 0C748DC7 0D8B4777 252CD4E1 01A1CEFC D57069CD C1B5E071 E591212D
80BE3A50 9062884E 57F4BF0C C0EFBF12 6509E384 E1196B8B 11C42280 80806D4B
F9290203 010001A3 66306430 0F060355 1D130101 FF040530 030101FF 30110603
551D1104 0A300882 06526F75 74657230 1F060355 1D230418 30168014 801FF21F
B68B4902 F183264C 381B00FF 31E04AD1 301D0603 551D0E04 16041480 1FF21FB6
8B4902F1 83264C38 1B00FF31 E04AD130 0D06092A 864886F7 0D010104 05000381
810072E2 23CBEABC B0D8ED1B 09835CAD 6D4D92C7 31880AF1 B9EC00DC 12DBDC2B
637FD4AB 39051AF3 04D3D948 180AB27A FFF66B33 6E44AB03 5280EC27 3C68C054
B365F6E3 5272D96F 9BBBC96E 228CC9C7 84F3CC48 28479B47 D8ADD129 7BF495FF
D8AFCA02 F8096B3C 581E68AA 16A00112 49FCED96 83DD2847 BA07F69D 9195248B EF31
quit
username INEM privilege 15 secret 5 $1$2Jgp$bV.OuBughjgSIOLuCr6Kn16FP.
archive
log config
hidekeys
controller DSL 0/0/0
mode atm
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet0/1
description Conection to CISCO SDM
ip address 10.10.10.1 255.255.255.248
ip tcp adjust-mss 1412
duplex auto
speed auto
interface ATM0/0/0
no ip address
no atm ilmi-keepalive
interface ATM0/0/0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Dialer0
ip address dhcp
ip mtu 1452
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname r353535
ppp chap password 0 xdfgdfg
ppp pap sent-username r353535 password 0 xdfgdfg
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
dialer-list 1 protocol ip permit
control-plane
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
end
Some one can help me please?
thanks

Hello,
Can you explain me please the reason of my WIC 1SHDSL-v3 not work in ADSL lines ?
Thank you,
Best Regards

Cisco 1760

I have a cisco 1760 router (see config attached) with one ADSL and one SHDSL card.The cd led on the adsl card turns green the atm interface is up but the bvi1 interface remains down.The router is not detecting the shdsl card.What can i do?

what IOS version have you got on it?
Please also paste the output of : sh ver

Cisco 1760 and VoIP gateway

Hello NetProf!
I'm repeating my request for help, mabey clearing a few things out.
1. We have a cisco 1760 router running CCME
2. Some connected to it cisco 79xx ip-phones
3. A third party gatekeeper - MikroTik router
4. Every device is logged in the gatekeeper, and every call i settled with the use of it.
5. We have a third party VoIP gateway - MultiTechs MultiVoIP - also registered in the gatekeeper.
6. Now the connections history:
a) when phoning from the gateway to cisco - everything works fine.
b) when phoning fromn cisco to the gateway - the connection failes - it looks like CISCO ISN'T FORWARDING ANY INDENTITY DATA - NO IP ADDRESS, AND H323-ID - GETS TO THE GATEWAY!!!!!
Please help!!
Michal Podoski

Check if there are some known issues documented here:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122relnt/1700/rn1700yj.htm

Cisco 1760 router stays in rommon modus

I am having problems with a cisco 1760 router. When I turn the router on I am getting stuck in rommon mode. When I enter the command: "boot flash:c1700-sv8y7-mz.123-11.T3.bin" , the router will boot the ios image. But when i turn the router off and on, it will return to rommon mode. I have tried the following commands in rommon mode:
rommon 1 > confreg 0x2102
rommon 2 > reset
or
rommon 1 > confreg 0x142
rommon 2 > reset
without results. I get the following errors:
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
Bad checksum on cookie structure, resorting to backup copy
Correcting primary cookie from backup
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number:      0x0
open: failed to find and/or load the bootloader: "flash:music-on-hold.au"
loadprog: error - on file open
boot: cannot load "c1700-sv8y7-mz.123-11.T3.bin"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number:      0x0
boot: cannot load "flash:"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
loadprog: bad file magic number:      0x0
boot: cannot load "flash:"
System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
rommon 1 >
rommon 1 >
Thanks,
Pieter

I would recommend posting in the netpro forums about this.
http://www.cisco.com/go/netpro
This site is for the Cisco Small Business Pro routers.
For your problem though, you might try looking at your boot system command in your running config to make sure that it is accurate.

Cisco 1760 router will not recognize wic1-dsu-t1-v2 card in slots 3 or 4

My 1760 router will not recognize a wic1-dsu-t1-v2 card in slots 3 or 4. They only work in slots 1 & 2. Never saw this before where the same card would not work in different slots.
Need assistance.
Thanks,
Ron
Router#show version
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-IPBASE-M), Version 12.3(6c), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 20-Jul-04 07:00 by kellythw
Image text-base: 0x80008120, data-base: 0x80C74650
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
Router uptime is 20 minutes
System returned to ROM by power-on
System image file is "flash:c1700-ipbase-mz.123-6c.bin"
cisco 1760 (MPC860P) processor (revision 0x500) with 55598K/9938K bytes of memory.
Processor board ID FOC0849230K (3846615071), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
WIC T1-DSU
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router#show flash
System flash directory:
File Length   Name/status
1   7517112 c1700-ipbase-mz.123-6c.bin
[7517176 bytes used, 25775112 available, 33292288 total]
32768K bytes of processor board System flash (Read/Write)
Router#show diag
Slot 0:
        C1760 1FE VE 4SLOT DV Mainboard Port adapter, 3 ports
        Port adapter is analyzed
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware Revision        : 5.0
        PCB Serial Number        : FOC0849230K
        Part Number              : 73-7167-05
        Board Revision           : B0
        Fab Version              : 04
        Product (FRU) Number     : CISCO1760
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 03 16 41 05 00 C1 8B 46 4F 43 30 38 34
          0x10: 39 32 33 30 4B 82 49 1B FF 05 42 42 30 02 04 FF
          0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        WIC/VIC Slot 0:
        FT1 4351
        Daughter card-Version 4 TLV Cookie Format
        Hardware Revision        : 1.1
        PCB Serial Number        : FOC09053XP1
        Part Number              : 73-8346-04
        Board Revision           : A0
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Deviation Number         : 0-0
        Product (FRU) Number     : WIC-1DSU-T1-V2
        Top Assy. Part Number    : 800-22193-02
        CLEI Code                : IP4I380GAB
        WIC/VIC Slot 1:
        FT1 4351
        Daughter card-Version 4 TLV Cookie Format
        Hardware Revision        : 1.2
        PCB Serial Number        : FOC10073JND
        Part Number              : 73-8346-05
        Board Revision           : A0
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Deviation Number         : 0-0
        Product (FRU) Number     : WIC-1DSU-T1-V2
        Top Assy. Part Number    : 800-22193-03
        CLEI Code                : IPUIAPRRAA

Hi Ron,
Slots 3 & 4 are for VICs only.
Have a look at the Location/ Function table here:
http://www.cisco.com/en/US/products/hw/routers/ps221/products_tech_note09186a00800c3399.shtml
cheers,
Seb.

Old 1760 With password recovery disabled, no way to factory reset

Hi
I have an old 1760 router with Password Recovery Functionality Disabled
I don't care about its actual configuration , I need factory reset
I Followed the well documented procedure :
Normal boot
Self decompressing the image : #################################################
################################################################ [OK]
Smart Init is disabled. IOMEM set to: 15
PMem allocated: 57042944 bytes; IOMem allocated: 10065920 bytes
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y7-M), Version 12.3(6d), RELEASE SOFTWARE (fc1
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Fri 15-Oct-04 03:46 by kellythw
Image text-base: 0x80008120, data-base: 0x81440804
Send break at this time , then :
Do you want to reset the router to factory default
configuration and proceed [y/n] ? y
Reset router configuration to factory default.
cisco 1760 (MPC860P) processor (revision 0x500) with 55706K/9830K bytes of memor
y.
Processor board ID FOC07450X9P (3881152211), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
WARNING:
Executing this command will disable password recovery mechanism.
Do not execute this command without another plan for
password recovery.
Are you sure you want to continue? [yes/no]: y
The router boot up normally anyway , still with original password unrecovered instead a fresh factory default.
Any hint please ?????
Thank you

Federico,
There is something quite strange going on but one thing has caught my attention in particular. This is a part of your transcript:
Send break at this time , then :
Do you want to reset the router to factory default configuration and proceed [y/n] ? y Reset router configuration to factory default.cisco 1760 (MPC860P) processor (revision 0x500) with 55706K/9830K bytes of memory.Processor board ID FOC07450X9P (3881152211), with hardware revision 0000MPC860P processor: part number 5, mask 2Bridging software.X.25 software, Version 3.0.0.1 FastEthernet/IEEE 802.3 interface(s)32K bytes of non-volatile configuration memory.32768K bytes of processor board System flash (Read/Write)WARNING:Executing this command will disable password recovery mechanism.Do not execute this command without another plan forpassword recovery.Are you sure you want to continue? [yes/no]: y
Notice that the first question is whether you want to erase the configuration - you respond with yes, and the router continues booting. The second question displayed clearly shows that the router continues loading the configuration file and in particular processes the no service password-recovery command.
What would happen if you answered with n to this second question, preventing the router from accepting the no password-recovery stored command? Could you reload the router afterwards and try the password recovery procedure again?
Also, if this router has a removable Flash card, would you be able to enter the ROMMON and set the configuration register to 0x2142 if you removed the card and tried booting the router?
Best regards,
Peter

Cisco 1760 my default GW. Optimizing external interface.

Hello, my current setup is....
[comcast 10 Mbps]<----->[Cisco 1760]<------->[Dell PowerConnect 3024]--------[LAN]
I have a WIC-1ENET on my 1760 connected to the the motorola cable modem. I was wondering if there are any specific commands I should apply to an external interface to improve performance, or keep unwanted traffic from being sent out.
interface Ethernet0/0
ip address dhcp
no ip redirects
no ip proxy-arp
ip nat outside
no ip route-cache cef
no ip route-cache
no ip mroute-cache
half-duplex
priority-group 1
no cdp enable
That is my current setup for my external interface. I have the priority set for my xbox 360. So that netflix gets highest priority. This allows for me to get HD streams 90% of the time, with little to no slow downs from others using the network. I would like to set full-duplex, but doing so brings the connections to the internet down to a crawl. I don't know if this is because the cable modem needs to be reset after full-duplex has been set, or what.
I have seen some configurations with a hold-queue value. Would this help me any? Speed tests using dlsreports i see about 8Mbps/1.5Mbps down/up. I have modified the nat tcp timeout to 10 minutes.
Thanks for any information guys.

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin-top:0cm;
mso-para-margin-right:0cm;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0cm;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Regarding the duplex settings on Ethernet 0/0 there are some rules in the standards. If you set the duplex manually on the interface auto negotiation is turned off and requested duplex will not be ‘announced’ to your cable modem. The default behavior according to the standard is for the cable modem to use half duplex. This will also happen if you set Ethernet 0/0 to full duplex since auto negotiation is turned off.
So in order to get full duplex you have two options:
1) Use the command ‘duplex auto’ on Ethernet 0/0
2) Configure both Ethernet 0/0 and your cable modem to full duplex.
André

CME B-ACD on Cisco 2911 with IOS 15.2(4)M5 not working

Hi Folks,
I am currently setting up CME version 9.1 with B-ACD (app-b-acd-aa-3.0.0.2.tcl & app-b-acd-3.0.0.2.tcl), running on
Cisco 2911 with IOS ver 15.2(4)M5, this is for lab purposes.
Below is my CME & B-ACD configuration :
voice service voip
ip address trusted list
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
h225 listen-port 1820
no call service stop
sip
bind control source-interface Vlan400
bind media source-interface Vlan400
registrar server expires max 600 min 60
voice register global
mode cme
source-address 172.25.202.1 port 5060
max-dn 2
max-pool 2
load 9971 sip9971.9-2-2SR1-9
authenticate register
timezone 28
time-format 24
date-format D/M/Y
tftp-path flash:
create profile sync 0004714411607756
voice register dn 1
number 3005
name br2phn2
voice register dn 2
number 3006
name br2phn4
voice register template 1
dialplan 1
voice register dialplan 1
type 7940-7960-others
pattern 1 3...
pattern 2 999
voice register pool 1
id mac 1C1D.86C4.0D6D
type 9971
number 1 dn 1
template 1
dtmf-relay rtp-nte
username 3005 password cisco
description 3214-3005
codec g711ulaw
voice register pool 2
id mac 1C1D.86C4.A574
type 9971
number 1 dn 2
template 1
dtmf-relay rtp-nte
username 3006 password cisco
description 3214-3006
codec g711ulaw
voice hunt-group 1 parallel
list 3002,3006
pilot 3210
application
service aa flash:/app-b-acd-aa-3.0.0.2.tcl
paramspace english index 1
param number-of-hunt-grps 2
param handoff-string aa
paramspace english language en
param max-time-vm-retry 2
param aa-pilot 3500
paramspace english location flash://
param second-greeting-time 60
param welcome-prompt _bacd_welcome.au
param call-retry-timer 15
param voice-mail 3001
param max-time-call-retry 90
param service-name queue
service aa-drop flash:/app-b-acd-aa-3.0.0.2.tcl
paramspace english index 1
param service-name queue
param drop-through-option 2
param second-greeting-time 60
paramspace english language en
param max-time-vm-retry 2
param max-time-call-retry 90
param voice-mail 3001
paramspace english location flash://
param aa-pilot 3501
param number-of-hunt-grps 1
param handoff-string aa-drop
param call-retry-timer 15
service queue flash:/app-b-acd-3.0.0.2.tcl
param queue-len 15
param aa-hunt10 3006
param queue-manager-debugs 1
param number-of-hunt-grps 2
param aa-hunt2 3210
interface Loopback0
ip address 172.25.110.3 255.255.255.255
ip ospf network point-to-point
h323-gateway voip interface
h323-gateway voip id Spain ipaddr 172.25.110.1 1719
h323-gateway voip h323-id BR2-RTR
h323-gateway voip tech-prefix 1#
h323-gateway voip bind srcaddr 172.25.110.3
interface Vlan400
ip address 172.25.202.1 255.255.255.0
ip pim dense-mode
dial-peer voice 3500 voip
service aa
destination-pattern 3500
session target ipv4:172.25.110.3
incoming called-number 3500
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 3501 voip
service aa-drop
destination-pattern 3501
session target ipv4:172.25.110.3
incoming called-number 3501
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
telephony-service
no auto-reg-ephone
max-ephones 2
max-dn 2 no-reg both
ip source-address 172.25.110.3 port 2000
cnf-file location flash:
load 7965 term65.default.loads
time-zone 28
time-format 24
date-format dd-mm-yy
max-conferences 8 gain -6
moh "music-on-hold.au"
web admin system name admin password cisco
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 14 2014 05:54:44
ephone-template 1
softkeys connected Endcall Hold Park Trnsfer Acct Flash
ephone-dn 1 octo-line
number 3001 no-reg both
description 3214-3001
name br2phn1
ephone-dn 2 octo-line
number 3002 no-reg both
description 3214-3002
name br2phn3
ephone 1
device-security-mode none
mac-address 189C.5DB6.D303
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7965
button 1:1
ephone 2
device-security-mode none
description 3214-3002
mac-address 984B.E194.FDDD
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7960
button 1:2
Problem :
1. When I test call from CME Phone both SIP and SCCP Phone by dial 3500 or 3501, I get the busy tone.
2. Debug voip dial-peer, match with dial-peer voice 3500 for (aa service) & 3501 for (aa-drop service).
3. Debug voice application script, show nothing.
Is there something wrong with my configuration ?
Rgds
Novri

Hi Novriadi,
In your configuration
service aa flash:/app-b-acd-aa-3.0.0.2.tcl
service queue flash:/app-b-acd-3.0.0.2.tcl
paramspace english location flash://
Remove "/" and "//" from the configuration
Then use the call application voice load command in privileged EXEC mode to reload the scripts.
Router# call application voice load aa
Router# call application voice load queue
Router# call application voice load aa-drop
You can refer to following document as well for more info
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/bacd/configuration/guide/cme40tcl/40bacd.html#wp1018270
Please find the sample configuration that is required to configure b-acd in CME for reference.
telephony-service
moh music-on-hold.au
multicast moh 239.1.1.1 port 2000
application
service queue flash:app-b-acd-2.1.0.0.tcl
param number-of-hunt-grps 2
param aa-hunt2 1111
param aa-hunt3 1222
param queue-len 15
param queue-manager-debugs 1
service aa flash:app-b-acd-aa-2.1.0.0.tcl
paramspace english index 1
paramspace english language en
paramspace english location flash:
param service-name queue
param handoff-string aa
param aa-pilot 8005550123
param welcome-prompt _bacd_welcome.au
param number-of-hunt-grps 2
param dial-by-extension-option 1
param second-greeting-time 60
param call-retry-timer 15
param max-time-call-retry 700
param max-time-vm-retry 2
param voice-mail 5003
dial-peer voice 222 voip
service aa
destination-pattern 8005550123
session target ipv4:192.168.1.1
incoming called-number 8005550123
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
Thanks & Regards,
Mudit Mathur

Cisco UCM with Third Party Contact Center Solution

Hi all, hope everyone is well.
Anyone out there running Cisco UCM with a third party contact center solution ? would love to hear your experience on this subject.
Thanks in advance !!
Danny

I have not heard of any sucessful stories, which vendor are you considering and what would you not go with UCCE/UCCX?
I used to work for Rockwell (Aspect today) which attempted to integrate their Business Contact Solution with CUCM (back on 3.3) and it worked OK for low volume calls, but never had any customer adoption.
I have not heard of any other known ACD vendors integrating with CUCM.
Chris

Using Cisco WCS with Microsoft IAS

Hi.
I have two 5508 and WCS 7.0.172. I want to user Active Directory users credintals to login on ther WCS. Have a configurated NPS role on server with windows 2008 r2.
I have read this http://zmq503o1.wordpress.com/2008/01/06/using-cisco-wcs-with-microsoft-ias/ and done the same.
I dont't agree with "on the "Encryption" tab and clear all the checkboxes except "No encryption" - wants an encryption connection but this didn't work till in user's properites in AD permit "Reversible encryption". This is not what that I want. Would I need to generate ssl-cert for the wcs as wroted this?http://www.cisco.com/en/US/docs/wireless/wcs/7.0MR1/configuration/guide/hard.html#wp1042471
or doing smth else? thx

Camera is only supported for use with CUVA. Any other application attempting to utilize the camera is not tested and is not supported.

Cisco IronPort with On Premise Exchange 2013

Hello All
The company I work for is in the process of starting an on premise Exchange 2007 to Exchange 2013 migration.
Most of the issues I don't think I'll have an issue with; however, where I am not finding much info is in regards to other companies using Cisco IronPort with Exchange 2013.
SO, I have two questions within this topic...
One, is anyone using Cisco IronPort with Exchange 2013 (on premise) out here?
Two, my manager is very controlling. I am the Exchange Admin; however, anything having to do with this IronPort thing with regards to Exchange HE has to do it. So, if anyone is familiar with this IronPort thing... How much work on the IronPort is going
to have to be done during this migration to keep things going?

It shouldn't be any different with Exchange 2013 than it is with Exchange 2007.
Ed Crowley MVP "There are seldom good technological solutions to behavioral problems."

Cisco 1700 with MP-BGP and VRF support

I have a Cisco 1721 with MP-BGP Support, you can create VRFs with it and every other MPLSVPN feature, but the commands for MPLS switching are not supported like Router(config-if)mpls ip , I read in some forums that you can create MPLS VPN without enabling MPLS at all, just with MPBGP, but I couldn't do it myself, Can someone tell me how to make it work or what can I do with a Cisco 1721 that supports MP-BGP?
thanks in advance

Here is an example. Take care about overhead for packets like VoIP. The overhead is 88 bytes.
The packet semms something like that.
IpHeader-pub@ - NAT-Tudp4500 - ESP - IpHeader-priv@(vrf discriminator) - GRE - Original IP Header - Data - Esp Trailer.
In this case you neet tunnel-mode because you use
private @ in order to determine vrf (vrf discriminator).
This is a LAB config, all other security parameters you need on a router are not configured. If you add access-list on the external interface of REMOTE you have to understand every encapsulation step in order to well tune it.
Good reading.
The PPT draw shows physically and logically views.
PS, take care about fragmentation issues, the problematic is still not well managed by the routers, I could not made Tunnel-path-mtu discovery work with vrf's. The workaround is to fragment packets. It's not good for performance but actually there is no other solution concerning that.
Kind Regards
Miguel

Cisco 2621 with 2821

I have a Cisco 2621 with 2FXS and 2FXO for my landlines, can I setup my 2821 to use my 2621 to make outside calls?
Sent from Cisco Technical Support iPhone App

That should work in my opinion. The 2821 is running CCME? But is that worth the effort? Can't you place the VWICs into the 2821 instead in the 2621?
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

1760 with 4 VIC2-4FXO

I want to use four FXO in a Router 1760, but I saw a limitation in the web that said:
Restrictions on VIC2-4FXO Usage
When configured for operation in countries that use the TBR21 mode, the use of VIC2-4FXO cards is subject to the following limitations.
· In the Cisco 1751 router, a maximum of one VIC2-4FXO card can be supported.
· In the Cisco 1760 router, a maximum of two VIC2-4FXO cards can be supported.
When not operating in the TBR21 mode, these limitations do not apply.
These restrictions do not apply to VIC2-2FXO cards
I have to install this equipment in Argentina but I dont know if that apply here.
Regards,

TBR21 is current limiting mode used in europe:
Use in Europe (TBR21 certification) requires modem firmware 1.0.1 and Cisco IOS Version 11.3(5)T or 12.0(1)T. You must load the modem microcode in addition to the Cisco IOS software.
For European countries, configure modem country microcom europe (this selects TBR21 operation). Country code "europe" requires Cisco IOS Version 11.3(5)T or 12.0(1)T.
You should not be in TBR21 mode in Argentina.
Hope this helps....

Cisco 1760 with shdsl

Similar Messages

Maybe you are looking for