Cisco 2432-24FXS Calls won't ring FXS ports when placed in Huntgroup
Hi,
I am having an issue getting calls to ring through on the FXS ports when using the "trunkgroup" command under the POTS dial-peers. Calls will ring through fine if I use the "port" command under the pots dial-peer. What I am trying to accomplish is getting a single number to hunt through 13 FXS ports in a round-robin fashion. With the below setup I am getting a SIP 404 not found message in the SIP debug info. I am not sure if I am missing something here or what the deal is. If the below information is not enough I would be happy to provide additional info. Any idea's why this configuration doesn't seam to work?
trunk group HuntGroup1
hunt-scheme round-robin both up
dial-peer voice 1 voip
translation-profile outgoing 7to11
destination-pattern .T
progress_ind setup enable 3
no modem passthrough
voice-class codec 1
session protocol sipv2
session target dns:XXXXXXXX
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
no vad
dial-peer voice 300 pots
trunkgroup HuntGroup1
description TEST NUMBER
destination-pattern XXXXXXXXXX
voice-port 2/0
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 1
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/1
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 2
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/2
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 3
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/3
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 4
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/4
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 5
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/5
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 6
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/6
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 7
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/7
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 8
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/8
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 9
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/9
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 10
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/10
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 11
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/11
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 12
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/12
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 13
station-id number XXXXXXXXXX
caller-id enable
Message was edited by: Thomas Schmidt
Added CCSIP Debug and Router Config.
Hi.
Can you please attach the complete config and a debug ccsip message?
Thanks
Regards
Carlo
Sent from Cisco Technical Support iPhone App
Similar Messages
-
My sound button cant function even the sound also not sound but when i received call, it do ring..just when i try to play utube or play music it will never have sound...please help me. now i'm using ios7. It just recently happened.
Hi hayscart,
This article contains steps to try when you are having trouble with the iPhone's speaker:
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
Cheers,
- Ari -
Transfer Calls from dect on FXS port (STCAPP)
Dear All,
I have a Dect phone that is connected to an FXS card in a Cisco Voicegateway 2900 series, i have configured it under stcapp.
Now the phone does work but it can't transfer to other internal phones. My question is how do i configure this, i have looked into stcapp supplementary services.
Voiceport
voice-port 0/3/1
cptone BE
timeouts interdigit 5
description === DECT 15360 ===
caller-id enable
Dial-peer
dial-peer voice 700 pots
service stcapp
port 0/3/0
dial-peer voice 701 pots
service stcapp
port 0/3/1
stcapp supplementary-services
port 0/2/1
fallback-dn 98307
port 0/3/0
fallback-dn 15360
port 0/3/1
fallback-dn 15360This is how to do transfer for a sccp controlled endpoint..
"During an active call, user presses hookflash and receives dial tone. User dials number for transfer and either stays online to announce (consultive transfer) or hangs up (blind transfer). When user hangs up, the call is transferred"
Please refer to the sccp supplemetary services feature guide
http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxssccpsplmft.html
Please rate all useful posts
"The essence of christianity is not the enthronement but the obliteration of self --William Barclay" -
CLID presentation fails on FXS port
i have a mgcp gateway with a nm-hd-2v , and the modules vic2-2fxo ,vic2-2fxs
The CLID of the external call is presented normally on my fxo port and displayed on the IP (soft-)phones.
I dont see the nr getting presented on the FXS port when i debug.
Called number and calling nr remains empty.
I see a calling nr when i do a csim start <exention>
caller-id enable is configured on the fxs port configuration at the gateway.
tried several type of caller-id alerting methodes without success.
When connecting the same phone on the pstn, i get the clid normally so it is something in the configuration
regardsHi,
Yes - you are correct. Looked at this one too quickly.
You will want to make sure the CPTONE defined on the port is for the country the phone is manufactured for, and that the voice-pport has the 'caller-id enable' command.
If those are both correct, and I'm guessing that they are since some caller-id works, then you need to inspect the gateways that take the calls to begin with.
Do you have caller-id trouble for internal calls also?
How do these calls come into your network?
hth,
nick -
My iPhone 5 won't ring . It only vibrates for calls, texts, etc. what am I doing wrong?
Hi, Mylenium,
Thanks for your prompt reply, I'm afraid it hasn't helped. I don't see anything wrong in my device manager.
I have also gone and updated every driver, especially the motherboard chipset and the Sata Intel Rapid Storage Technology driver.
Unfortunately, this hasn't made any difference.
Any other suggestions?
Many thanks in advance!
Hugo -
Questions regarding FaceTime: When I call someone, it rings but they can't answer and when someone calls me via FaceTime it won't even ring.
Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems
http://tinyurl.com/32drz3d
Cheers, Tom -
My iPhone won't ring when the caller is "Unknown". How do I make it ring?
Do you even see the call come in on the phone? Do you see the missed call in your list? Or do you just get a voice mail.
If it never even shows up in your missed calls list, contact your carrier. Perhaps you have anonymous call blocking on your account. (I wish I did...) -
I have OS Maverick; my FaceTime account is activated; when I call someone on FT, I hear it ring and if the person answers we can have a good conversation; all my settings seem to be fine, however, my FT just won't ring or register any miss call.
I HAVE MAVERICK BUT NOT CERTAIN WHICH VERSION.Thanks John UK. I checked the firewall but it set to allow all incoming calls. So, I am still at square one. Any further suggestions?
-
How can I fix my phone's ringer? The call comes through but it won't ring.
I've had my iPhone for over 6 months now with no issues. I have not had it reserviced, its not refurbished, and I bought it new from an AT&T store.
This week my phone stopped ringing. The incoming call comes through on the screen, but it doesn't ring out loud so I know I'm getting a call and I can't sit and stare at my iPhone's screen all day long to see if I'm getting an incoming call. It vibrates when a call comes in maybe 20% of the time.
Today I went into settings and reset my settings but it still didn't bring my ringer back. It plays the ringers when you are looking through the list of ringers, it plays it when you alter the volume setting, but when a call is actually coming in or when I'm receiving a text message or something, no sound.
What can I do to get my ringer back?Check the mute switch on the side above the volume rocker. If the red dot shows, the phone is muted. You'll still be able to play the ringtones to select one.
I find that the switch can be thrown to "mute" by accident when I put my iPhone in my belt holster. -
My iphone won't ring for me to answer or when I send a call, no dial tone.
when I get phone call, I miss it because it doesn't ring and also when I make a call, there is no dial tone.
Try a reset. Hold the sleep/wake and home buttons together until you see the Apple logo and then release. After the phone starts back up, see if it will work. Also, I have never witnessed a cell phone give you a dial tone. You dial a number, then press send for the call to go through.
-
Cisco SIP Phone 9971 won't register on CME 8.6 or 8.5 Please HELP
Please help me , I have problem with registering Cisco SIP phone 9971 with CME 8.6 on ISR 2901.
I configured CME for SIP clients, then I add configuration for 9971 phone and create profiles. Phone downloaded SEP...xml file from CME,after that phone look for g4-tones.xml and gd-sip.jar files, I added them to CME after that phone downloaded them and reboot. Now phone is stuck in some kind of loop and does not register on CME.
On phone log I can see repeting next few messeges.
12:01:58a No DNS Server IP
12:01:59a Updating Trust list
12:01:59a No Trust List instaled
12:01:59a SEP04C5AB03B0D.cnf.xml (TFTP) // at this time phone download SEP...xml file from CME
12:02:00a VPN Error: VPN is not Configured
on CME if issue DEBUG TFTP EVENTS i receive next few lines
*Aug 18 18:20:19.891: TFTP: Looking for CTLSEP04C5A4B03B0D.tlv
*Aug 18 18:20:19.987: TFTP: Looking for ITLSEP04C5A4B03B0D.tlv
*Aug 18 18:20:20.083: TFTP: Looking for ITLFile.tlv
*Aug 18 18:20:20.347: TFTP: Looking for SEP04C5A4B03B0D.cnf.xml
*Aug 18 18:20:20.351: TFTP: Opened flash:/SEP04C5A4B03B0D.cnf.xml, fd 14, size 4585 for process 141
*Aug 18 18:20:20.363: TFTP: Finished flash:/SEP04C5A4B03B0D.cnf.xml, time 00:00:00 for process 141
here you can see verison info of CME
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 24-Mar-11 15:31 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
ELTOSAN_ROUTER uptime is 1 hour, 50 minutes
System returned to ROM by reload at 16:29:20 UTC Thu Aug 18 2011
System image file is "flash:/c2900-universalk9-mz.SPA.151-4.M.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
Cisco CISCO2901/K9 (revision 1.0) with 471040K/53248K bytes of memory.
Processor board ID FGL1508252Y
3 Gigabit Ethernet interfaces
2 terminal lines
1 Virtual Private Network (VPN) Module
4 Voice FXO interfaces
4 Voice FXS interfaces
1 Internal Services Module (ISM) with Services Ready Engine (SRE)
Survivable Remote Site Voicemail (SRSV) on Cisco Unity Express (CUE) 8.5.1 in slot/sub-slot 0/0
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
254464K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2901/K9 xxxxxxxxxxxxx
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc uck9 Permanent uck9
data None None None
Configuration register is 0x2102
this is RUNNING CONFIGURATION
! Last configuration change at 16:10:12 UTC Thu Aug 18 2011
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ELTOSAN_ROUTER
boot-start-marker
boot system flash:/c2900-universalk9-mz.SPA.151-4.M.bin
boot-end-marker
no aaa new-model
no ipv6 cef
ip source-route
no ip routing
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.5.1 192.168.5.10
ip dhcp excluded-address 192.168.5.200 192.168.5.255
ip dhcp pool phone
network 192.168.5.0 255.255.255.0
default-router 192.168.5.251
option 150 ip 192.168.5.251
ip dhcp pool data
relay source 192.168.2.0 255.255.255.0
relay destination 192.168.2.201
multilink bundle-name authenticated
crypto pki token default removal timeout 0
voice-card 0
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
fax protocol pass-through g711alaw
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 192.168.5.251 port 5060
max-dn 6
max-pool 6
load 9971 sip9971.9-1-1SR1.loads
authenticate register
tftp-path flash:
create profile sync 0005135312289902
voice register dn 1
number 207
allow watch
name GossaVM
label 207
voice register dn 3
number 101
name Dejan
label 101
mwi
voice register pool 1
id mac 000C.29C5.0011
number 1 dn 1
dtmf-relay sip-notify
username testvm password testera
codec g711alaw
voice register pool 3
id mac 04C5.A4B0.3B0D
type 9971
number 3 dn 3
presence call-list
dtmf-relay rtp-nte
username dejan password 1234
codec g711alaw
no vad
license udi pid CISCO2901/K9 sn xxxxxxxxxxxx
hw-module ism 0
hw-module pvdm 0/0
redundancy
interface GigabitEthernet0/0
description INTERFACE INTERNAL
no ip address
no ip route-cache
duplex auto
speed auto
no mop enabled
interface GigabitEthernet0/0.2
description LAN DATA
encapsulation dot1Q 2
ip address 192.168.2.251 255.255.255.0
no ip route-cache
interface GigabitEthernet0/0.5
description LAN VOICE
encapsulation dot1Q 5
ip address 192.168.5.251 255.255.255.0
no ip route-cache
interface ISM0/0
no ip address
no ip route-cache
shutdown
!Application: SRSV-CUE Running on ISM
interface GigabitEthernet0/1
no ip address
no ip route-cache
shutdown
duplex auto
speed auto
interface ISM0/1
description Internal switch interface connected to Internal Service Module
shutdown
interface Vlan1
no ip address
no ip route-cache
shutdown
ip forward-protocol nd
no ip http server
no ip http secure-server
snmp-server community public RO
tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
tftp-server flash:sip9971.9-1-1SR1.loads alias sip9971.9-1-1SR1.loads
tftp-server flash:United_States/g4-tones.xml
tftp-server flash:English_United_States/gd-sip.jar
control-plane
voice-port 0/0/0
voice-port 0/0/1
voice-port 0/0/2
voice-port 0/0/3
voice-port 0/1/0
voice-port 0/1/1
voice-port 0/1/2
voice-port 0/1/3
mgcp profile default
gatekeeper
shutdown
line con 0
line aux 0
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password jebiga
login
transport input all
end
I did not have any kind of problem with X-LITE to register to CME. also try with few SCCP phones 7940 and I did not any kind of problem .
this is content of SEP....xml file for 9971
<device>
<deviceProtocol>SIP</deviceProtocol>
<devicePool>
<dateTimeSetting>
<dateTemplate>M/D/YA</dateTemplate>
<timeZone>Pacific Standard/Daylight Time</timeZone>
<ntps>
<ntp priority="0">
<name>0.0.0.0</name>
<ntpMode>unicast</ntpMode>
</ntp>
</ntps>
</dateTimeSetting>
<callManagerGroup>
<members>
<member priority="0">
<callManager>
<ports>
<sipPort>5060</sipPort>
</ports>
<processNodeName>192.168.5.251</processNodeName>
</callManager>
</member>
</members>
</callManagerGroup>
</devicePool>
<sipProfile>
<sipProxies>
<registerWithProxy>true</registerWithProxy>
</sipProxies>
<sipCallFeatures>
<cnfJoinEnabled>true</cnfJoinEnabled>
<localCfwdEnable>true</localCfwdEnable>
<callForwardURI>service-uri-cfwdall</callForwardURI>
<callPickupURI>service-uri-pickup</callPickupURI>
<callPickupGroupURI>service-uri-gpickup</callPickupGroupURI>
<callHoldRingback>2</callHoldRingback>
<semiAttendedTransfer>true</semiAttendedTransfer>
<anonymousCallBlock>2</anonymousCallBlock>
<callerIdBlocking>2</callerIdBlocking>
<dndControl>2</dndControl>
<remoteCcEnable>true</remoteCcEnable>
</sipCallFeatures>
<sipStack>
<remotePartyID>true</remotePartyID>
</sipStack>
<sipLines>
<line button="1" lineIndex="1">
<featureID>9</featureID>
<featureLabel></featureLabel>
<proxy>USECALLMANAGER</proxy>
<port>5060</port>
<name></name>
<displayName></displayName>
<autoAnswer>
<autoAnswerEnabled>2</autoAnswerEnabled>
</autoAnswer>
<callWaiting>1</callWaiting>
<authName>dejan</authName>
<authPassword>1234</authPassword>
<sharedLine>false</sharedLine>
<messagesNumber></messagesNumber>
<ringSettingActive>5</ringSettingActive>
<forwardCallInfoDisplay>
<callerName>true</callerName>
<callerNumber>true</callerNumber>
<redirectedNumber>true</redirectedNumber>
<dialedNumber>true</dialedNumber>
</forwardCallInfoDisplay>
</line>
<line button="2" lineIndex="2">
<featureID>9</featureID>
<featureLabel>101</featureLabel>
<proxy>USECALLMANAGER</proxy>
<port>5060</port>
<name>101</name>
<displayName>Dejan Rakic</displayName>
<autoAnswer>
<autoAnswerEnabled>2</autoAnswerEnabled>
</autoAnswer>
<callWaiting>1</callWaiting>
<authName>dejan</authName>
<authPassword>1234</authPassword>
<sharedLine>false</sharedLine>
<messagesNumber></messagesNumber>
<ringSettingActive>5</ringSettingActive>
<forwardCallInfoDisplay>
<callerName>true</callerName>
<callerNumber>true</callerNumber>
<redirectedNumber>true</redirectedNumber>
<dialedNumber>true</dialedNumber>
</forwardCallInfoDisplay>
</line>
</sipLines>
<enableVad>true</enableVad>
<preferredCodec>g711alaw</preferredCodec>
<dialTemplate></dialTemplate>
<kpml>1</kpml>
<phoneLabel></phoneLabel>
<stutterMsgWaiting>2</stutterMsgWaiting>
<disableLocalSpeedDialConfig>true</disableLocalSpeedDialConfig>
<dscpForAudio>184</dscpForAudio>
<dscpVideo>136</dscpVideo>
</sipProfile>
<commonProfile>
<phonePassword>1234</phonePassword>
<callLogBlfEnabled>2</callLogBlfEnabled>
</commonProfile>
<featurePolicyFile>featurePolicyDefault.xml</featurePolicyFile>
<loadInformation>sip9971.9-1-1SR1.loads</loadInformation>
<vendorConfig>
</vendorConfig>
<commonConfig>
<videoCapability>0</videoCapability>
<ciscoCamera>0</ciscoCamera>
</commonConfig>
<sshUserId>dejan</sshUserId>
<sshPassword>1234</sshPassword>
<userId></userId>
<phoneServices>
<provisioning>2</provisioning>
<phoneService type="1" category="0">
<name>Missed Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/MissedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="1" category="0">
<name>Received Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/ReceivedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="1" category="0">
<name>Placed Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/PlacedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="2" category="0">
<name>Voicemail</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/Voicemail</url>
<vendor></vendor>
<version></version>
</phoneService>
</phoneServices>
<versionStamp>0131511014412102</versionStamp>
<userLocale>
<name>English_United_States</name>
<langCode>en</langCode>
</userLocale>
<networkLocale>United_States</networkLocale>
<networkLocaleInfo>
<name>United_States</name>
</networkLocaleInfo>
<authenticationURL></authenticationURL>
<directoryURL></directoryURL>
<servicesURL>http://192.168.5.251:80/CMEserverForPhone/serviceurl</servicesURL>
<dscpForSCCPPhoneServices>0</dscpForSCCPPhoneServices>
<dscpForCm2Dvce>96</dscpForCm2Dvce>
<transportLayerProtocol>2</transportLayerProtocol>
</device>Hello,
I'm facing exactly the same problem, that is:
a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
I have read all the postings to this Forum, but I have not been able to solve it.
In my case the commands voice register dn and voice register pool are OK.
So frankly, I have no idea what I could be missing.
I'm pasting the Router's config.
I hope somebody is able to point me in the right direction.
Here is the config. Thank you!
C2811#sh run
Building configuration...
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname C2811
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 172.25.140.1 172.25.140.10
ip dhcp excluded-address 172.35.140.1 172.35.140.10
ip dhcp pool Data
network 172.25.140.0 255.255.255.0
default-router 172.25.140.1
option 150 ip 172.25.140.1
dns-server 172.25.140.1
ip dhcp pool Voice
network 172.35.140.0 255.255.255.0
default-router 172.35.140.1
option 150 ip 172.35.140.1
dns-server 172.35.140.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections sip to sip
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 172.25.140.1 port 5060
max-dn 40
max-pool 42
load 9971 sip9971.9-4-1-9.loads
authenticate register
authenticate realm cisco
tftp-path flash:
create profile sync 0004820400584603
voice register dn 1
number 1010
allow watch
name Phone10
label Phone10
mwi
voice register pool 1
id mac 189C.5DB6.BD09
type 9971
number 1 dn 1
presence call-list
dtmf-relay rtp-nte
username adm password adm
call-forward b2bua busy 68600
codec g711ulaw
no vad
camera
video
voice-card 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879153754
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879153754
revocation-check none
rsakeypair TP-self-signed-1879153754
crypto pki certificate chain TP-self-signed-1879153754
certificate self-signed 01
(details ommited)
license udi pid CISCO2811 sn FTX1146A44H
username admin privilege 15 password 0 admin
redundancy
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.25
description Data VLAN
encapsulation dot1Q 25
ip address 172.25.140.1 255.255.255.0
interface FastEthernet0/0.35
description Voice VLAN
encapsulation dot1Q 35
ip address 172.35.140.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
tftp-server flash:P00308010200.bin
tftp-server flash:P00308010200.sbn
tftp-server flash:P00308010200.sb2
tftp-server flash:P00308010200.loads
tftp-server flash:SCCP42.9-3-1SR3-1S.loads
tftp-server flash:apps42.9-3-1ES19.sbn
tftp-server flash:cnu42.9-3-1ES19.sbn
tftp-server flash:cvm42sccp.9-3-1ES19.sbn
tftp-server flash:dsp42.9-3-1ES19.sbn
tftp-server flash:jar42sccp.9-3-1ES19.sbn
tftp-server flash:term42.default.loads
tftp-server flash:term62.default.loads
tftp-server flash:SCCP45.9-3-1SR3-1S.loads
tftp-server flash:apps45.9-3-1ES19.sbn
tftp-server flash:cnu45.9-3-1ES19.sbn
tftp-server flash:cvm45sccp.9-3-1ES19.sbn
tftp-server flash:dsp45.9-3-1ES19.sbn
tftp-server flash:jar45sccp.9-3-1ES19.sbn
tftp-server flash:term45.default.loads
tftp-server flash:term65.default.loads
tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
ml
tftp-server flash:sip9971.9-4-1-9.loads
tftp-server flash:kern9971.9-4-1-9.sebn
tftp-server flash:rootfs9971.9-4-1-9.sebn
tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
control-plane
mgcp profile default
telephony-service
max-ephones 24
max-dn 48
ip source-address 172.25.140.1 port 2000
cnf-file location flash:
load 7960-7940 P00308010200
load 7942 SCCP42.9-3-1SR3-1S.loads
load 7945 SCCP45.9-3-1SR3-1S.loads
load 7962 SCCP42.9-3-1SR3-1S.loads
load 7965 SCCP45.9-3-1SR3-1S.loads
max-conferences 8 gain -6
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
ephone-dn 1
number 1001
description Phone 1
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 1002
description Phone 2
name Phone 2
hold-alert 30 originator
ephone-dn 3
number 1003
description Phone 3
name Phone 3
hold-alert 30 originator
ephone 1
device-security-mode none
mac-address 001C.58FB.6E0F
button 1:1
ephone 2
device-security-mode none
mac-address 0014.A981.7F8A
button 1:2
ephone 3
device-security-mode none
mac-address 0006.5356.A4B8
button 1:3
alias exec con conf t
alias exec sib show ip int brief
alias exec srb show run | b
alias exec sri show run int
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
scheduler allocate 20000 1000
ntp master 1
end
C2811# -
Call Manager register fxs port with voice gateway- problem
I have a CUCM 6 and a Voice Gateway V224. I've configured the voice gateway's voice FXS ports as MGCP.
I have a Voip connected and registered to the CUCM and a Pots phone connected to the Voice Gateway.
If i dial from the Voip to the Pots phone it rings. The problem is that i cannot ring from the Pots to the Voip phone.
I have no dial tone.
If i write no shut down on the voice port i have a tone. If i configure mgcp on the voice port i have a busy ringtone.
I've entered no mgcp and mgcp commands and i've reset the voice gateway.
How can i call from the pots to the voip phone?
The ios version on the voice gateway is Version 12.4(22)T4.
Here is an outghtput from the Voice gateway.
ccm-manager mgcp
ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 10.1.1.33
ccm-manager config
mgcp
mgcp call-agent CCMIOSS 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp validate domain-name
mgcp rtp payload-type g726r16 static
mgcp profile default
timeout tone busy 600
timeout tone dial 600
dial-peer voice 999223 pots
service mgcpapp
port 2/23
dial-peer voice 999222 pots
service mgcpapp
port 2/22
dial-peer voice 999888 pots
service mgcpapp
port 2/23
The CUCM 6 is registered with the voice gateway.Is your campaign using CPA? If so, what's the behavior if CPA is not enabled?
I think the best thing to do is to run a trace...
Call Manager > Cisco Unified Serviceability > Trace > Configurations
Select a CUCM server - any subscriber would work.
Service Group - CM Services
Cisco CallManager (Inactive)
Enable SIP Stack Trace and apply to all nodes. Download and install RTMT
Make a bunch of outbound tests and then open RTMT > Trace & Log Central > Collect Files > Check "All Servers" for Cisco CallManager > Next > Next > Relative Range if you made the test calls within the last X minutes, otherwise you can set a From and To datetime. Click Finish and go through your SDL logs and see what errors you find and post them here.
Also, make sure your phone is in the correct CSS in Call Manager -
Iphone 5: Incoming Calls won't go through.
Hello everyone,
I purchased the Iphone 5 about 1-2 weeks ago and so far i love it. However as of recently i've been expeirencing a few issues where incoming calls won't go through.
I'll try my best to break it down:
Someone calls me.
Phone "rings" on their side.
My iPhone doesn't ring.
I get no notification of a missed call, and maybe a few minutes later i'll be alerted to a missed call or a voicemail.
I've tested various things that i assume would cause the issue, but so far none of them seem to be the case.
I even went to Verizon (a few minutes ago actually) and they did a soft-reset (pretty much what i did prior) and soon as i got home i called the phone and nothing went through. I waited about a minute, called again, and then i rang. However seconds later i tried calling again, and it didn't ring.
Also it happens are random times. First insident was a few nights ago around 10 PM. Then again a few days ago around 3 PM and finally this morning around 8-8:30 AM.
No my "Do not disturb" isn't on.
I have good (if not great) connection.
At home the phone is always on WiFi
Yes i've tried turning off LTE.
Yes i've done a network reset.
Yes, phone is up to date.
One question i have is could it be only having this issue at my house? I have no way of testing if it only happens at my home (cause no one really has that kind of time to waste with me lol) so i'm not sure.I want to ensure those important calls get through Huxable! I understand why you are concerned!
My first recommendation would be to make sure you are power cycling the device(turning off and on) at least once a day. This allows the device to refresh with the network and update the tower information on 4G handsets.
Second, it will definitely be valuable to test the device in different locations to determine whether it is a location issue versus an equipment issue. If this happens in multiple locations for example, it is likely device related.
If you find the issues occur mainly inside your home, the network extender accessory is an excellent option to boost indoor signal strength.
http://bit.ly/AKkC
Sincerely,
JonathanK_VZW
VZW Support
Follow Us on Twitter@VZWSupport -
Cisco SIP Phone 9971 won't register on CME 8.6
Hello,
I'm facing a very strange problem:
a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
I have read all the related-postings to this and other Forum, but I have not been able to solve it.
One of the "potential solutions" was to make sure that the Phone had a Line configured.
But I think that the commands voice register dn and voice register pool are properly configured (see config below)
So frankly, I have no idea what I could be missing.
I'm pasting the Router's config.
I hope somebody is able to point me in the right direction.
Here is the config. Thank you!
C2811#sh run
Building configuration...
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname C2811
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 172.25.140.1 172.25.140.10
ip dhcp excluded-address 172.35.140.1 172.35.140.10
ip dhcp pool Data
network 172.25.140.0 255.255.255.0
default-router 172.25.140.1
option 150 ip 172.25.140.1
dns-server 172.25.140.1
ip dhcp pool Voice
network 172.35.140.0 255.255.255.0
default-router 172.35.140.1
option 150 ip 172.35.140.1
dns-server 172.35.140.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections sip to sip
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 172.25.140.1 port 5060
max-dn 40
max-pool 42
load 9971 sip9971.9-4-1-9.loads
authenticate register
authenticate realm cisco
tftp-path flash:
create profile sync 0004820400584603
voice register dn 1
number 1010
allow watch
name Phone10
label Phone10
mwi
voice register pool 1
id mac 189C.5DB6.BD09
type 9971
number 1 dn 1
presence call-list
dtmf-relay rtp-nte
username adm password adm
call-forward b2bua busy 68600
codec g711ulaw
no vad
camera
video
voice-card 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879153754
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879153754
revocation-check none
rsakeypair TP-self-signed-1879153754
crypto pki certificate chain TP-self-signed-1879153754
certificate self-signed 01
(details ommited)
license udi pid CISCO2811 sn FTX1146A44H
username admin privilege 15 password 0 admin
redundancy
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.25
description Data VLAN
encapsulation dot1Q 25
ip address 172.25.140.1 255.255.255.0
interface FastEthernet0/0.35
description Voice VLAN
encapsulation dot1Q 35
ip address 172.35.140.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
tftp-server flash:P00308010200.bin
tftp-server flash:P00308010200.sbn
tftp-server flash:P00308010200.sb2
tftp-server flash:P00308010200.loads
tftp-server flash:SCCP42.9-3-1SR3-1S.loads
tftp-server flash:apps42.9-3-1ES19.sbn
tftp-server flash:cnu42.9-3-1ES19.sbn
tftp-server flash:cvm42sccp.9-3-1ES19.sbn
tftp-server flash:dsp42.9-3-1ES19.sbn
tftp-server flash:jar42sccp.9-3-1ES19.sbn
tftp-server flash:term42.default.loads
tftp-server flash:term62.default.loads
tftp-server flash:SCCP45.9-3-1SR3-1S.loads
tftp-server flash:apps45.9-3-1ES19.sbn
tftp-server flash:cnu45.9-3-1ES19.sbn
tftp-server flash:cvm45sccp.9-3-1ES19.sbn
tftp-server flash:dsp45.9-3-1ES19.sbn
tftp-server flash:jar45sccp.9-3-1ES19.sbn
tftp-server flash:term45.default.loads
tftp-server flash:term65.default.loads
tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
ml
tftp-server flash:sip9971.9-4-1-9.loads
tftp-server flash:kern9971.9-4-1-9.sebn
tftp-server flash:rootfs9971.9-4-1-9.sebn
tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
control-plane
mgcp profile default
telephony-service
max-ephones 24
max-dn 48
ip source-address 172.25.140.1 port 2000
cnf-file location flash:
load 7960-7940 P00308010200
load 7942 SCCP42.9-3-1SR3-1S.loads
load 7945 SCCP45.9-3-1SR3-1S.loads
load 7962 SCCP42.9-3-1SR3-1S.loads
load 7965 SCCP45.9-3-1SR3-1S.loads
max-conferences 8 gain -6
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
ephone-dn 1
number 1001
description Phone 1
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 1002
description Phone 2
name Phone 2
hold-alert 30 originator
ephone-dn 3
number 1003
description Phone 3
name Phone 3
hold-alert 30 originator
ephone 1
device-security-mode none
mac-address 001C.58FB.6E0F
button 1:1
ephone 2
device-security-mode none
mac-address 0014.A981.7F8A
button 1:2
ephone 3
device-security-mode none
mac-address 0006.5356.A4B8
button 1:3
alias exec con conf t
alias exec sib show ip int brief
alias exec srb show run | b
alias exec sri show run int
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
scheduler allocate 20000 1000
ntp master 1
end
C2811#Thank you for your reply.
I did some debugs and the results are very strange!
This is what I got:
Feb 24 18:01:12.219: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 400 Bad Request
Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK08011844
From: ;tag=189c5db6bd09000260cf3daf-289a76d1
To: ;tag=52488-160A
Date: Mon, 24 Feb 2014 18:01:12 GMT
Call-ID: [email protected]
CSeq: 1000 REFER
Content-Length: 0
Contact:
Feb 24 18:01:12.291: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
REGISTER sip:172.25.140.1 SIP/2.0
Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK1e9ad079
From: ;tag=189c5db6bd0900032df02e9c-25d79707
To:
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 01 Jan 1982 00:02:41 GMT
CSeq: 101 REGISTER
User-Agent: Cisco-CP9971/9.4.1
Contact: ;+sip.instance="
000000-0000-0000-0000-189c5db6bd09>";+u.sip!devicename.ccm.cisco.com="SEP189C5DB
6BD09";+u.sip!model.ccm.cisco.com="493";video
Supported: replaces,join,sdp-anat,norefersub,resource-priority,extended-refer,X-
cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-
cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-6.0.2,X-cisco-xsi-
8.0.1
Content-Length: 0
Reason: SIP;cause=200;text="cisco-alarm:22 Name=SEP189C5DB6BD09 ActiveLoad=sip99
71.9-4-1-9.loads InactiveLoad=sip9971.9-3-2SR1-1.loads Last=reset-reset"
Expires: 3600
Feb 24 18:01:12.395: voice_reg_get_reg_expires_timer: no voice register pool found
Feb 24 18:01:12.395: VOICE_REG_POOL: Register request for (1010) from (172.35.140.12)
Feb 24 18:01:12.395: VOICE_REG_POOL: Contact matches pool 1 number list 1
Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
Feb 24 18:01:12.395: VOICE_REG_POOL: key(1010) contact(172.35.140.12:5060) add to contact table
Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (1010) found in contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(1010) contact(172.35.140.12) added to contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) add to srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) added to srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
But right after these errors, I get the following:
Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
VOICE_REG_POOL pool_tag(1), dn_tag(1)
Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
Name:SEP189C5DB6BD09 IP:172.35.140.12 DeviceType:Phone
Feb 24 18:01:12.411: VOICE_REG_POOL: Pool[1]: service-control (reset type: 2) message sent to sip:[email protected]
Feb 24 18:01:12.411: voice_reg_privacy_update_to_phone: delay sending privacy update during bulk registration
Feb 24 18:01:12.415: //1/7B0070C28003/SIP/Msg/ccsipDisplayMsg:
====================
And when I do a sh voice register pool, I get the following:
C2811#sh voice register pool 1
Pool Tag 1
Config:
Mac address is 189C.5DB6.BD09
Type is 9971
Number list 1 : DN 1
Proxy Ip address is 0.0.0.0
Current Phone load version is Cisco-CP9971/9.4.1
DTMF Relay is enabled, rtp-nte
Call Waiting is enabled
DnD is disabled
Video is enabled
Camera is enabled
Busy trigger per button value is 0
call-forward b2bua busy 68600
keep-conference is enabled
registration expires timer max is 3600 and min is 120
username adm password adm
kpml signal is enabled
Lpcor Type is none
blf call list is enabled
Transport type is udp
service-control mechanism is supported
registration Call ID is [email protected]
Registration method: per line
Privacy feature is not configured.
Privacy button is disabled
active primary line is: 1010
contact IP address: 172.35.140.12 port 5060
Phone SIS Version: 6.0.2
GW SIS Version: 1.0.0
Dialpeers created:
Dial-peers for Pool 1:
dial-peer voice 40001 voip
destination-pattern 1010
session target ipv4:172.35.140.12:5060
session protocol sipv2
dtmf-relay rtp-nte
digit collect kpml
codec g711ulaw bytes 160
no vad
call-fwd-busy 68600
after-hours-exempt FALSE
Statistics:
Active registrations : 4
Total SIP phones registered: 1
Total Registration Statistics
Registration requests : 4
Registration success : 4
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time : 18:11:43.551 UTC Mon Feb 24 2014
Last unregister request time :
Register success time : 18:11:43.551 UTC Mon Feb 24 2014
Unregister success time :
C2811#
So apparently the Phone is actually registered!
However, the Phone screens still shows this message: Phone Not Registered.
So frankly I don't understand what's going on!
I really hope somebody can help. Thanks! -
Setting up PLAR with Cisco Unity Connection Call Handler
This is a lab setup and Im doing it to learn. No customer involvement.
Setup
Analog phones - FXS Port - 2951 Router - FXS port - FXO Port - 2951 Router - CUCM 9 - UC 9
|------------PSTN Emulator-------------| |-----MGCP GW----------|
I have a CTI Route Point configured as DN 7000 and it has the default VM profile. The CTI RP is set to FWD All to VM.
The FXO port is set to PLAR to 7000.
When I dial from the PSTN analog phones through the FXO port, I hear the first ring, the FXO port answers, then I hear what sounds like the recorded message beginning to play. Immediately after, I hear the recorded message "You cannot be transferred to this number. Check the number and try again."
I dont do anything and within a second or two, I hear the recorded message for the system call handler start.
I did some more testing. I added an E1 trunk between the PSTN and the MGCP gateway. In the CUCM, I created another CTI Route Point with a DN that I could dial from my PSTN cloud. I also set that CTI Route point up to Call FWD all to VM.
When I dial using the E1 trunk, the call hits the system call handler as expected and I hear my recorded greeting (as expected).
However, calling through the FXS-FXO tie line consistently gets me the error message recording followed by my recorded greeting.
Im currently using loopstart on the tie line, though I have also tried ground start with no difference.
Any ideas?
JeffIf I understand correctly, you want outside calls to go directly to the call handler but internal calls to ring whatever phone this extension is on.
If I am understanding correctly, then this will probably resolve it. For the purposes of the explanation I will assume that extension 1000 is the number in question:
Create a new partition, we'll just call it ToVM or something like that
Create a new CTI route point with extension 1000 and put it in the ToVM partition, forward all calls for this CTI route point to voicemail
If you don't have one already, create a calling search space for the voice gateway. Call it Gateway-CSS. This should have the same partitions that the gateway can normally call, but it should also have the ToVM partition and that partition should be HIGHER in the list than the partition that has the normal extension 1000 on it.
Apply Gateway-CSS to the gateway
Configure the normal extension 1000 (not in the ToVM partition) the way that you want it to work.
Now when external callers dial 1000 they will go to the call handler because that partition is higher in the CSS and the CTI Route point should be hit first. Internal callers will ring the phone (or whatever it is) because they only have access to the regular internal partition (and not ToVM) that 1000 is in.
This is all assuming that I understand you correctly!
Maybe you are looking for
-
Photo Printing from Networked Windows 7
My HP Photosmart Printer is USB connected to a Windows XP machine which is directly attached to the home network. Also have a Windows 7 64 machine wirelessly connected to the home network. The Photosmart printer was added to the windows 7 machine
-
I have some .mov files that I am unable to put on my AppleTV because iTunes will not let me change them. I receive a message "could not be converted because this file does not allow saving or conversion." I also tried to do this using Quicktime, thou
-
Error when reading Excel as a source OLE or COM processing error:
I received the following error when reading an Excel sheet directly into a target template table. Nothing fancy, but the error pops up immediately. I have found the problem and am posting the error and resolution to hopefully help others, -rs- 69
-
how do I find claim # to register printer I just purchased?
-
Delete and full load into ODS versus Full load into ODS
Can someone please advise, that in the context of DSO being populated with overwrite function, would the FULL LOAD in following two options (1 and 2) take the same amount of time to execute or one would take lesser than the other. Please also explain