Cisco 2500 with DSL

hi there, I have two cisco 2500 routers, having AUI interfaces. both locations have DSL connection from verizon,. is there anyway i can use these routers with DSL if yes then do i need to buy any special module

Hello.
the only way I could see you router being integrated into a DSL solution is by connecting the Ethernet port of your ADSL router/modem to the Ethernet AUI port of your 2500. But unless you have a 2514 (which has two Ethernet ports), that would still not get you anywhere, since you need an additional Ethernet port to connect your switch...
Regards,
GP

Similar Messages

Cisco E1000/ Westel Model 327W with DSL connection

I have a Westel model 327W for my DSL service. I received it from my internet provider (Bellsouth). I recently purchased a Cisco E1000 router for what I though was a easy connect. For two days off and on I have tried to connect them but I have not been able. I'm not very computer smart but I do know the basics. I have managed to cripple one desktop and a laptop that had wireless or ethernet to the point the system tells me they are not equiped with wireless cards and my wireless range on the computer I'm typing on is about 5 feet. Can someone explain to me how to connect the Westel DSL to the Cisco router.

The Cisco Connect software comes with the Linksys Wireless-N (E/EA - Series) routers that let you manage your network easier. For the setup process, you need to perform the following:
i. Verify that there is an active Internet connection between the computer and modem
ii. Setting up the router using Cisco Connect
QUICK TIPS:
The router’s power adapter needs to be plugged to your router and into an available power outlet.
If using a wired connection, the first Ethernet cable needs to be plugged to the computer’s LAN port into any of the router’s blue numbered Ethernet ports.
The second Ethernet cable should be plugged to the modem’s Internet port and the other end into the router’s yellow Internet port.
Ensure that you have no firewall enabled that may prevent the router from being detected.
Here is the link for setting up a Linksys router with DSL Internet service: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r...

Cisco or Linksys DSL router that will work with Windows XP Pro?

Any suggestions for a CISCO or LINKSYS DSL router to replace a Zyxel (Century Link) PK5001Z? System is Windows XP Pro, 20 wireless and wired devices connected (including 6 CISCO WVC210 IP cameras ). The Zyxel forwards as many ports as I want, but will only open a limited number of the ports. This limits my access thru the internet (local network sees all cameras). Zyxel support is unable to help.

Hi Edward, if you're looking for a modem/router combo device, Cisco offers the SRP500 series. However this product is EOS/EOL. The small business product line does not have any other DSL termination router aside the SRP series. If your goal is to use a DSL modem and then have a router, you may want to consider RV325 router as it is very feature rich and quite robust.
-Tom
Please mark answered for helpful posts

Unable to configure PPPoE in Cisco 877 for DSL connectivity

Hi,
I am trying to setup a DSL connection with Cisco 877 as the CPE. The CLI does not list the option of PPPoE for protocol in the vpdn group config prompt. If i manually enter PPPoE as the encapsulation, the vpdn group configured vanishes from the config!
Any clues? Has anyone got a sample config for a cisco 877 connecting to DSL through PPPoE. I followed the sample config in the TAC website giving the example for cisco 827-pppoe -DSL.
Some more inputs - as soon as i connect the DSL line the ATM interface line protocol comes up but unable to see anything in debug vpdn or debug ppp auth. The router IOS feature set is Advanced Security services.
Regards
NSG

Hi Gnanavel,
You need bba-group instead :
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/ftpprfls.htm#wp1088274
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1839/products_feature_guide09186a00801541b8.html#wp1027195
Thanks and Regards,
~Zulfiqar

Using a Cisco RV180W with wired LAN

Hello everyone!
I have a small client with a pair of RV180W's. They wish to create one large wireless area where users can walk around from the area around one 'router' to the other without needing to reset their wireless connection on their mobile device. Logically the client wishes to setup a WDS repeater. Except, the building the client is in, is very old and made from materials that will block the 2.4GHz microwave signal once a user exits one room and enters another room. (Obviously the APs are in totally opposite ends of the building, and can hardly detect the presence of their sister access points.)
There is lots of cat-5 between the rooms and the client thought what they might do is run their data over the wire between the two APs using the 'LAN' ports on each AP for the backbone communication. For the life of me I cannot figure out how to make such a scenario work, I've looked high and low and cannot find anything on this (besides the implication in some documentation that what my client wants is impossible).
I did set the two APs up, as stand alone access points (one AP, call it the primary, connects to the Internet via the 'WAN' interface, there is a backbone link on a 'LAN' interface to the secondary AP which connects to the same wire on one of it's 'LAN' interfaces.) Of course as I noted before if a user walks from the room with the primary to the room with the secondary the user needs to establish a new connection although, by design, the SSIDs and passphrase are the same. This design is unacceptable to the client and they... well they are hopping angry that they cannot get what they think ought to be really easy.
What I'd like to know is:
1. Is what the client is asking for possible with the hardware they have?
2. Can I do it with additional equipment? I'm looking at the Cisco 2500 Series Wireless controller or possibly a Virtual Wireless Controller? (Given that the client is blaming me for the fact that it doesn't work -hey I was handed the device and told to make it work, I had no say in what hardware was bought-, whatever additional stuff I tell them they need to buy needs to a. work, and b. be cheap.)
3. Any other thoughts, or comments?
Thanks!

Thanks Ganesh!!
So... basically it's just what I'm doing now but instead of using
ip nat inside source static udp 10.10.10.10 53 dialer 0 53
I will need to use:
ip nat inside source static udp 10.10.10.10 53 123.123.123.123 53 extendable
ip nat inside source static udp 10.10.10.11 53 123.123.123.124 53 extendable
I have also in the mean time been told on the Bind mailing list that Bind will accept transmissions like this as I thought the the decapsulation and re-encapsulation of the router would cause a problem with the software!
So looks like all is good now :-)
Regards,
Kaya

Can't add my new license on my cisco 2500 wireless controller

hello,
i already have 25 license installed on my Cisco 2500 wireless controller.
but when i need add my new bundle license, i can't see him on my admin panel.
i following this steps for installing my new license :
1- i go on WLC panel
2- management => software activation => commands
3- i select "install license"
4- i setting a correct path
5- when i clic on "install license", i can see two following message : "File transfer operation started" and "Installation Process Completed ". but when i go on "licenses" i can't see
tanks for help

Hi Serge,
In case you have another license installed on the controller with higher license than the one that you are installing, then the license installation will fail.
In case you want to install a new license with higher number of AP count, then you can install it, then save and reboot the controller.
Also I noticed when you install a new license and the summation of the previously installed license and the newly installed license is exceeding the max allowed AP count on the controller, then the installation will fail.
In such scenario, deactivate the current license by making the evaluation license priority to high, then after that install the new license and then change the priority to medium and make the evaluation license to low in addition to the previous license.
Kind Regards
Mohammad Setan

Cisco 2500 dual band router. the hp printer is connects on one band, pc the other help

Cisco 2500 wireless router Dual Band N, HP PhotoSmart C309-g, Windows 7
PC cannot find the printer because it connects on a different band. Cisco uses the same name for both bands. How do I get both devices on the same network.

I also have a dual band router, Cisco's LinkSys EA3500 N750; and the 5.0gHz band is necessary to avoid interference with other equipment operating on 2.4gHz. I put TP-link 2.4/5.0 gHz adapters on each PC (one HP another Sony, both a few years old) and the PCs now work fine, no loss of internet/network access. Would that solution also work for the printer? The printer does not recognize any network (even though the 2.4gHz shows as available and strong on the TP-link device. I used the same name and security code for the new router as the old; again, neither PC had a problem finding it.

Cisco 1841 with PPP Internet link down

Hi brothers, please help.
We have Cisco 1841 with ATM card connect to Internet . Some days one Dialer interface of ISP is down and only restart router to get Dialer interface up again. I check debug PPP negotiation & see that no inbound packets from ISP.
I really need to fix this issue permanently, not need to restart router to recover Internet.
Thanks!
All line protocol from ATM0/0/0 & Dialer interfaces are up, but Dialer interface cannot get allocated IP addresses.
interface ATM0/0/0
description ISP Internet
no ip address
no atm ilmi-keepalive
dsl operating-mode itu-dmt
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 2
interface Dialer2
description ISP Internet 1
mtu 1492
bandwidth 8000
ip address negotiated
ip nat outside
no ip virtual-reassembly in
encapsulation ppp
dialer pool 2
dialer-group 2
ppp authentication chap callin
ppp chap hostname xxx
ppp chap password 7 xxx
no cdp enable
wr1#show ip int br
Interface                  IP-Address      OK? Method Status                Protocol
ATM0/0/0                   unassigned      YES NVRAM up                    up
ATM0/1/0                   unassigned      YES NVRAM up                    up
Dialer2                    unassigned      YES IPCP   up                    up
wr1#show int atm0/0/0
ATM0/0/0 is up, line protocol is up
Hardware is HWIC-DSLSAR (with Alcatel ADSL Module), address is 001f.9e87.xxx(bia 001f.9e87.xxx)
Description: ISP Internet
MTU 4470 bytes, sub MTU 4470, BW 832 Kbit/sec, DLY 610 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Keepalive not supported
Encapsulation(s): AAL5
23 maximum active VCs, 256 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output 23:48:07, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 1084
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     58124 packets input, 30790858 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 348 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     51848 packets output, 16773091 bytes, 0 underruns
     6 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
wr1#show int dia2
Dialer2 is up, line protocol is up (spoofing)
Hardware is Unknown
Description: ISP Internet
Internet address will be negotiated using IPCP
MTU 1492 bytes, BW 8000 Kbit/sec, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Closed, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Interface is bound to Vi2
Last input never, output never, output hang never
Last clearing of "show interface" counters 1d00h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Class-based queueing
Output queue: 0/1000/0 (size/max total/drops)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     52937 packets input, 30470954 bytes
     52931 packets output, 17287959 bytes
Bound to:
Virtual-Access2 is up, line protocol is down
Hardware is Virtual Access interface
MTU 1492 bytes, BW 8000 Kbit/sec, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent
PPPoATM vaccess, cloned from Dialer2
Vaccess status 0x44
Bound to ATM0/0/0 VCD: 1, VPI: 0, VCI: 38, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 5 seconds on reset
Interface is bound to Di2 (Encapsulation PPP)
Last input 00:00:09, output never, output hang never
Last clearing of "show interface" counters 1d00h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 40403
Queueing strategy: Class-based queueing
Output queue: 65/1000/0 (size/max total/drops)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     58124 packets input, 30591958 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     93405 packets output, 17935575 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
syslog for debug ppp negotiation:
2014-09-10 08:49:31   Local7.Notice   local IP address   801: wr1.lon: .Sep 10 01:51:33.803: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0/0, changed state to down
2014-09-10 08:49:32   Local7.Notice   local IP address   804: wr1.lon: .Sep 10 01:51:35.247: %TRACKING-5-STATE: 3 ip sla 3 state Up->Down
2014-09-10 09:13:40   Local7.Error   local IP address   808: wr1.lon: Sep 10 02:15:42.646: %LINK-3-UPDOWN: Interface ATM0/0/0, changed state to up
2014-09-10 09:13:40   Local7.Notice   local IP address   809: wr1.lon: Sep 10 02:15:43.646: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0/0, changed state to up
2014-09-10 09:13:45   Local7.Error   local IP address   810: wr1.lon: Sep 10 02:15:48.957: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
2014-09-10 09:13:45   Local7.Debug   local IP address   811: wr1.lon: Sep 10 02:15:48.961: Interface Virtual-Access2 max_reserved_bandwidth config will not
2014-09-10 09:13:45   Local7.Debug   local IP address   812: wr1.lon: take effect on the queueing features configured via service-policy
2014-09-10 09:13:45   Local7.Info   local IP address   813: wr1.lon: Sep 10 02:15:48.965: %DIALER-6-BIND: Interface Vi2 bound to profile Di2
2014-09-10 09:13:45   Local7.Debug   local IP address   814: wr1.lon: Sep 10 02:15:48.965: Vi2 PPP: Sending cstate UP notification
2014-09-10 09:13:45   Local7.Debug   local IP address   815: wr1.lon: Sep 10 02:15:48.969: Vi2 PPP: Processing CstateUp message
2014-09-10 09:13:45   Local7.Debug   local IP address   816: wr1.lon: Sep 10 02:15:48.973: PPP: Alloc Context [662C56A4]
2014-09-10 09:13:45   Local7.Debug   local IP address   817: wr1.lon: Sep 10 02:15:48.973: ppp3 PPP: Phase is ESTABLISHING
2014-09-10 09:13:45   Local7.Debug   local IP address   818: wr1.lon: Sep 10 02:15:48.973: Vi2 PPP: Using dialer call direction
2014-09-10 09:13:45   Local7.Debug   local IP address   819: wr1.lon: Sep 10 02:15:48.973: Vi2 PPP: Treating connection as a callout
2014-09-10 09:13:45   Local7.Debug   local IP address   820: wr1.lon: Sep 10 02:15:48.973: Vi2 PPP: Session handle[14000004] Session id[3]
2014-09-10 09:13:45   Local7.Debug   local IP address   821: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP: Event[OPEN] State[Initial to Starting]
2014-09-10 09:13:45   Local7.Debug   local IP address   822: wr1.lon: Sep 10 02:15:48.973: Vi2 PPP: No remote authentication for call-out
2014-09-10 09:13:45   Local7.Debug   local IP address   823: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP: O CONFREQ [Starting] id 1 len 14
2014-09-10 09:13:45   Local7.Debug   local IP address   824: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:13:46   Local7.Debug   local IP address   825: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:46   Local7.Debug   local IP address   826: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP: Event[UP] State[Starting to REQsent]
2014-09-10 09:13:48   Local7.Debug   local IP address   827: wr1.lon: Sep 10 02:15:50.965: Vi2 LCP: O CONFREQ [REQsent] id 2 len 14
2014-09-10 09:13:48   Local7.Debug   local IP address   828: wr1.lon: Sep 10 02:15:50.965: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:13:48   Local7.Debug   local IP address   829: wr1.lon: Sep 10 02:15:50.965: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:48   Local7.Debug   local IP address   830: wr1.lon: Sep 10 02:15:50.965: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:50   Local7.Debug   local IP address   831: wr1.lon: Sep 10 02:15:52.981: Vi2 LCP: O CONFREQ [REQsent] id 3 len 14
2014-09-10 09:13:50   Local7.Debug   local IP address   832: wr1.lon: Sep 10 02:15:52.981: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:13:50   Local7.Debug   local IP address   833: wr1.lon: Sep 10 02:15:52.981: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:50   Local7.Debug   local IP address   834: wr1.lon: Sep 10 02:15:52.981: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:52   Local7.Debug   local IP address   835: wr1.lon: Sep 10 02:15:54.996: Vi2 LCP: O CONFREQ [REQsent] id 4 len 14
2014-09-10 09:13:52   Local7.Debug   local IP address   836: wr1.lon: Sep 10 02:15:54.996: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:13:52   Local7.Debug   local IP address   837: wr1.lon: Sep 10 02:15:54.996: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:52   Local7.Debug   local IP address   838: wr1.lon: Sep 10 02:15:55.000: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:54   Local7.Debug   local IP address   839: wr1.lon: Sep 10 02:15:57.012: Vi2 LCP: O CONFREQ [REQsent] id 5 len 14
2014-09-10 09:13:54   Local7.Debug   local IP address   840: wr1.lon: Sep 10 02:15:57.012: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:13:54   Local7.Debug   local IP address   841: wr1.lon: Sep 10 02:15:57.012: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:54   Local7.Debug   local IP address   842: wr1.lon: Sep 10 02:15:57.012: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:56   Local7.Debug   local IP address   843: wr1.lon: Sep 10 02:15:59.028: Vi2 LCP: O CONFREQ [REQsent] id 6 len 14
2014-09-10 09:13:56   Local7.Debug   local IP address   844: wr1.lon: Sep 10 02:15:59.028: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:13:56   Local7.Debug   local IP address   845: wr1.lon: Sep 10 02:15:59.028: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:56   Local7.Debug   local IP address   846: wr1.lon: Sep 10 02:15:59.028: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:58   Local7.Debug   local IP address   847: wr1.lon: Sep 10 02:16:01.044: Vi2 LCP: O CONFREQ [REQsent] id 7 len 14
2014-09-10 09:13:58   Local7.Debug   local IP address   848: wr1.lon: Sep 10 02:16:01.044: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:13:58   Local7.Debug   local IP address   849: wr1.lon: Sep 10 02:16:01.044: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:58   Local7.Debug   local IP address   850: wr1.lon: Sep 10 02:16:01.044: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:14:00   Local7.Debug   local IP address   851: wr1.lon: Sep 10 02:16:03.060: Vi2 LCP: O CONFREQ [REQsent] id 8 len 14
2014-09-10 09:14:00   Local7.Debug   local IP address   852: wr1.lon: Sep 10 02:16:03.060: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:14:00   Local7.Debug   local IP address   853: wr1.lon: Sep 10 02:16:03.060: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:14:00   Local7.Debug   local IP address   854: wr1.lon: Sep 10 02:16:03.060: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:14:02   Local7.Debug   local IP address   855: wr1.lon: Sep 10 02:16:05.075: Vi2 LCP: O CONFREQ [REQsent] id 9 len 14
2014-09-10 09:14:02   Local7.Debug   local IP address   856: wr1.lon: Sep 10 02:16:05.075: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:14:02   Local7.Debug   local IP address   857: wr1.lon: Sep 10 02:16:05.075: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:14:02   Local7.Debug   local IP address   858: wr1.lon: Sep 10 02:16:05.075: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:14:04   Local7.Debug   local IP address   859: wr1.lon: Sep 10 02:16:07.091: Vi2 LCP: O CONFREQ [REQsent] id 10 len 14
2014-09-10 09:14:04   Local7.Debug   local IP address   860: wr1.lon: Sep 10 02:16:07.091: Vi2 LCP:    MRU 1492 (0x010405D4)
2014-09-10 09:14:04   Local7.Debug   local IP address   861: wr1.lon: Sep 10 02:16:07.091: Vi2 LCP:    MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:14:04   Local7.Debug   local IP address   862: wr1.lon: Sep 10 02:16:07.091: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:14:06   Local7.Debug   local IP address   863: wr1.lon: Sep 10 02:16:09.107: Vi2 PPP DISC: LCP failed to negotiate
2014-09-10 09:14:06   Local7.Debug   local IP address   864: wr1.lon: Sep 10 02:16:09.107: PPP: NET STOP send to AAA.
2014-09-10 09:14:06   Local7.Debug   local IP address   865: wr1.lon: Sep 10 02:16:09.107: Vi2 PPP: No remote authentication for call-out
2014-09-10 09:14:06   Local7.Debug   local IP address   866: wr1.lon: Sep 10 02:16:09.107: Vi2 LCP: Event[Timeout-] State[REQsent to Stopped]
2014-09-10 09:14:06   Local7.Debug   local IP address   867: wr1.lon: Sep 10 02:16:09.107: Vi2 LCP: Event[DOWN] State[Stopped to Starting]
2014-09-10 09:14:06   Local7.Debug   local IP address   868: wr1.lon: Sep 10 02:16:09.107: Vi2 PPP: Phase is DOWN

Hello ,
As line comes up after reloading the device this does not looks like configuration issue but hardware .
Either connection between ATM card and modem is getting idle or some issue with ATM card .
Did you try replacing ATM card with a spare one to see if issue persists .
HTH
Sunil Bhadauria
! Kindly rate all helpful posts and accordingly mark correct answers to help forum !

CISCO 1841 with SHDSL Problem?

Hello,
I´am new in cisco WIC configuration. I have a CISCO 1841 with a interface: 1SHDSL v3 and i want to connect to my ISP over a PPoE encapsulation.
I just make the new interface connection in SDM, but the synchronism with the ISP not work. The ISP tell me that VPI/VCI is 0.35 and the annex is the A.
I live in the Europe, but i think that the annex A is for POTS lines and Annex B for ISDN, right?? My line is ADSL Analog.
My startup-configuration is that:
Router#show run
Building configuration...
Current configuration : 2974 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
dot11 syslog
ip source-route
ip cef
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-2879799878
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2879799878
revocation-check none
rsakeypair TP-self-signed-2879799878
crypto pki certificate chain TP-self-signed-2879799878
certificate self-signed 01
3082023E 308201A7 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32383739 37393938 3738301E 170D3131 30343233 32303532
33345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 38373937
39393837 3830819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100BE34 379A4D5D 1DA98B67 708AF8D4 221F1BE5 C5947EEA FF931EF4 37AD8A2C
C786C8D9 88E97474 D32FE0F0 10C048B9 6F5DA580 55241E61 9B0D849A D9E7182A
04D6C8E0 0C748DC7 0D8B4777 252CD4E1 01A1CEFC D57069CD C1B5E071 E591212D
80BE3A50 9062884E 57F4BF0C C0EFBF12 6509E384 E1196B8B 11C42280 80806D4B
F9290203 010001A3 66306430 0F060355 1D130101 FF040530 030101FF 30110603
551D1104 0A300882 06526F75 74657230 1F060355 1D230418 30168014 801FF21F
B68B4902 F183264C 381B00FF 31E04AD1 301D0603 551D0E04 16041480 1FF21FB6
8B4902F1 83264C38 1B00FF31 E04AD130 0D06092A 864886F7 0D010104 05000381
810072E2 23CBEABC B0D8ED1B 09835CAD 6D4D92C7 31880AF1 B9EC00DC 12DBDC2B
637FD4AB 39051AF3 04D3D948 180AB27A FFF66B33 6E44AB03 5280EC27 3C68C054
B365F6E3 5272D96F 9BBBC96E 228CC9C7 84F3CC48 28479B47 D8ADD129 7BF495FF
D8AFCA02 F8096B3C 581E68AA 16A00112 49FCED96 83DD2847 BA07F69D 9195248B EF31
quit
username INEM privilege 15 secret 5 $1$2Jgp$bV.OuBughjgSIOLuCr6Kn16FP.
archive
log config
hidekeys
controller DSL 0/0/0
mode atm
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet0/1
description Conection to CISCO SDM
ip address 10.10.10.1 255.255.255.248
ip tcp adjust-mss 1412
duplex auto
speed auto
interface ATM0/0/0
no ip address
no atm ilmi-keepalive
interface ATM0/0/0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Dialer0
ip address dhcp
ip mtu 1452
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname r353535
ppp chap password 0 xdfgdfg
ppp pap sent-username r353535 password 0 xdfgdfg
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
dialer-list 1 protocol ip permit
control-plane
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
end
Some one can help me please?
thanks

Hello,
Can you explain me please the reason of my WIC 1SHDSL-v3 not work in ADSL lines ?
Thank you,
Best Regards

How to Configuration Cisco 3725 with NEC ASPILA EX

Dear all;
Now i have Cisco 3725 with 1-Port Channelized E1/T1/ISDN-PRI, i am connect to NEC ASPILA EX with PRI I/F (1PRIU-A1.
The controller link state up, but when clients dialin to RAS not have ring back or not connect to RAS.
anyone can help me?

Hi;
i'am config cisco as you recommended is "isdn protocol-emulate network" and "clock source should be internal". After the remote computer call to RAS it have modem signal and then connected, next time it disconnect. can i change some parameter for this problem or what i'am wrong?. I post config, status, and debug message for you. Help me..
===== show isdn status ===========
#show isdn status
Global ISDN Switchtype = primary-net5
ISDN Serial2/0:15 interface
******* Network side configuration *******
dsl 0, interface ISDN Switchtype = primary-net5
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0xFFFF7FFF
Number of L2 Discards = 0, L2 Session ID = 0
Total Allocated ISDN CCBs = 0
=============== sh controllers e1 2/0 brief ========
#sh controllers e1 2/0 brief
E1 2/0 is up.
Applique type is Channelized E1 - unbalanced
No alarms detected.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
Module type is Channelized E1/T1 PRI
Version info Firmware: 0000001D, FPGA: 0
Hardware revision is 0.0 , Software revision is 29
Protocol revision is 1
number of CLI resets is 0
receive remote alarm : 0,
transmit remote alarm : 0,
receive AIS alarm : 0,
transmit AIS alarm : 0,
loss of frame : 1,
loss of signal : 1,
Loopback test : 0,
transmit AIS in TS 16 : 0,
receive LOMF alarm : 0,
transmit LOMF alarm : 0,
========== Interface config.=============
controller E1 2/0
clock source internal
line-termination 75-ohm
pri-group timeslots 1-31
interface Serial2/0:15
no ip address
ip nat inside
encapsulation ppp
ip policy route-map nachi-worm
dialer rotary-group 1
dialer-group 1
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice modem
no fair-queue
no cdp enable
=================Debug Message when call to RAS ===========================
Mar 6 22:40:29 BANGKOK: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x000B
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838B
Exclusive, Channel 11
Calling Party Number i = 0x0081, N/A
Plan:Unknown, Type:Unknown
Called Party Number i = 0x81, '075205600'
Plan:ISDN, Type:Unknown
Low Layer Compat i = 0x8090A3
High Layer Compat i = 0x9181
Mar 6 22:40:29 BANGKOK: ISDN Se2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x800B
Channel ID i = 0xA9838B
Exclusive, Channel 11
Mar 6 22:40:29 BANGKOK: ISDN Se2/0:15 Q931: TX -> ALERTING pd = 8 callref = 0x800B
Mar 6 22:40:29 BANGKOK: ISDN Se2/0:15 Q931: TX -> CONNECT pd = 8 callref = 0x800B
Mar 6 22:40:35 BANGKOK: %ISDN-6-CONNECT: Interface Serial2/0:10 is now connected to unknown unknown
Mar 6 22:40:46 BANGKOK: %ISDN-6-DISCONNECT: Interface Serial2/0:10 disconnected from unknown , call lasted 17 seconds
Mar 6 22:40:46 BANGKOK: ISDN Se2/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x800B
Cause i = 0x8290 - Normal call clearing
Mar 6 22:40:47 BANGKOK: ISDN Se2/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x000B
Mar 6 22:40:47 BANGKOK: ISDN Se2/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x800B
==============================================

CME B-ACD on Cisco 2911 with IOS 15.2(4)M5 not working

Hi Folks,
I am currently setting up CME version 9.1 with B-ACD (app-b-acd-aa-3.0.0.2.tcl & app-b-acd-3.0.0.2.tcl), running on
Cisco 2911 with IOS ver 15.2(4)M5, this is for lab purposes.
Below is my CME & B-ACD configuration :
voice service voip
ip address trusted list
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
h225 listen-port 1820
no call service stop
sip
bind control source-interface Vlan400
bind media source-interface Vlan400
registrar server expires max 600 min 60
voice register global
mode cme
source-address 172.25.202.1 port 5060
max-dn 2
max-pool 2
load 9971 sip9971.9-2-2SR1-9
authenticate register
timezone 28
time-format 24
date-format D/M/Y
tftp-path flash:
create profile sync 0004714411607756
voice register dn 1
number 3005
name br2phn2
voice register dn 2
number 3006
name br2phn4
voice register template 1
dialplan 1
voice register dialplan 1
type 7940-7960-others
pattern 1 3...
pattern 2 999
voice register pool 1
id mac 1C1D.86C4.0D6D
type 9971
number 1 dn 1
template 1
dtmf-relay rtp-nte
username 3005 password cisco
description 3214-3005
codec g711ulaw
voice register pool 2
id mac 1C1D.86C4.A574
type 9971
number 1 dn 2
template 1
dtmf-relay rtp-nte
username 3006 password cisco
description 3214-3006
codec g711ulaw
voice hunt-group 1 parallel
list 3002,3006
pilot 3210
application
service aa flash:/app-b-acd-aa-3.0.0.2.tcl
paramspace english index 1
param number-of-hunt-grps 2
param handoff-string aa
paramspace english language en
param max-time-vm-retry 2
param aa-pilot 3500
paramspace english location flash://
param second-greeting-time 60
param welcome-prompt _bacd_welcome.au
param call-retry-timer 15
param voice-mail 3001
param max-time-call-retry 90
param service-name queue
service aa-drop flash:/app-b-acd-aa-3.0.0.2.tcl
paramspace english index 1
param service-name queue
param drop-through-option 2
param second-greeting-time 60
paramspace english language en
param max-time-vm-retry 2
param max-time-call-retry 90
param voice-mail 3001
paramspace english location flash://
param aa-pilot 3501
param number-of-hunt-grps 1
param handoff-string aa-drop
param call-retry-timer 15
service queue flash:/app-b-acd-3.0.0.2.tcl
param queue-len 15
param aa-hunt10 3006
param queue-manager-debugs 1
param number-of-hunt-grps 2
param aa-hunt2 3210
interface Loopback0
ip address 172.25.110.3 255.255.255.255
ip ospf network point-to-point
h323-gateway voip interface
h323-gateway voip id Spain ipaddr 172.25.110.1 1719
h323-gateway voip h323-id BR2-RTR
h323-gateway voip tech-prefix 1#
h323-gateway voip bind srcaddr 172.25.110.3
interface Vlan400
ip address 172.25.202.1 255.255.255.0
ip pim dense-mode
dial-peer voice 3500 voip
service aa
destination-pattern 3500
session target ipv4:172.25.110.3
incoming called-number 3500
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 3501 voip
service aa-drop
destination-pattern 3501
session target ipv4:172.25.110.3
incoming called-number 3501
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
telephony-service
no auto-reg-ephone
max-ephones 2
max-dn 2 no-reg both
ip source-address 172.25.110.3 port 2000
cnf-file location flash:
load 7965 term65.default.loads
time-zone 28
time-format 24
date-format dd-mm-yy
max-conferences 8 gain -6
moh "music-on-hold.au"
web admin system name admin password cisco
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 14 2014 05:54:44
ephone-template 1
softkeys connected Endcall Hold Park Trnsfer Acct Flash
ephone-dn 1 octo-line
number 3001 no-reg both
description 3214-3001
name br2phn1
ephone-dn 2 octo-line
number 3002 no-reg both
description 3214-3002
name br2phn3
ephone 1
device-security-mode none
mac-address 189C.5DB6.D303
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7965
button 1:1
ephone 2
device-security-mode none
description 3214-3002
mac-address 984B.E194.FDDD
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7960
button 1:2
Problem :
1. When I test call from CME Phone both SIP and SCCP Phone by dial 3500 or 3501, I get the busy tone.
2. Debug voip dial-peer, match with dial-peer voice 3500 for (aa service) & 3501 for (aa-drop service).
3. Debug voice application script, show nothing.
Is there something wrong with my configuration ?
Rgds
Novri

Hi Novriadi,
In your configuration
service aa flash:/app-b-acd-aa-3.0.0.2.tcl
service queue flash:/app-b-acd-3.0.0.2.tcl
paramspace english location flash://
Remove "/" and "//" from the configuration
Then use the call application voice load command in privileged EXEC mode to reload the scripts.
Router# call application voice load aa
Router# call application voice load queue
Router# call application voice load aa-drop
You can refer to following document as well for more info
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/bacd/configuration/guide/cme40tcl/40bacd.html#wp1018270
Please find the sample configuration that is required to configure b-acd in CME for reference.
telephony-service
moh music-on-hold.au
multicast moh 239.1.1.1 port 2000
application
service queue flash:app-b-acd-2.1.0.0.tcl
param number-of-hunt-grps 2
param aa-hunt2 1111
param aa-hunt3 1222
param queue-len 15
param queue-manager-debugs 1
service aa flash:app-b-acd-aa-2.1.0.0.tcl
paramspace english index 1
paramspace english language en
paramspace english location flash:
param service-name queue
param handoff-string aa
param aa-pilot 8005550123
param welcome-prompt _bacd_welcome.au
param number-of-hunt-grps 2
param dial-by-extension-option 1
param second-greeting-time 60
param call-retry-timer 15
param max-time-call-retry 700
param max-time-vm-retry 2
param voice-mail 5003
dial-peer voice 222 voip
service aa
destination-pattern 8005550123
session target ipv4:192.168.1.1
incoming called-number 8005550123
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
Thanks & Regards,
Mudit Mathur

Cisco UCM with Third Party Contact Center Solution

Hi all, hope everyone is well.
Anyone out there running Cisco UCM with a third party contact center solution ? would love to hear your experience on this subject.
Thanks in advance !!
Danny

I have not heard of any sucessful stories, which vendor are you considering and what would you not go with UCCE/UCCX?
I used to work for Rockwell (Aspect today) which attempted to integrate their Business Contact Solution with CUCM (back on 3.3) and it worked OK for low volume calls, but never had any customer adoption.
I have not heard of any other known ACD vendors integrating with CUCM.
Chris

Error in Cisco 2500 series Wireless Controller

I have this error in Cisco 2500 series Wireless Controller
The AP type Cisco AIR-CAP35021-A-K9
I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series Wireless Controller But the AP get ip .
Please can any on help me .
Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode:

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller

Using Cisco WCS with Microsoft IAS

Hi.
I have two 5508 and WCS 7.0.172. I want to user Active Directory users credintals to login on ther WCS. Have a configurated NPS role on server with windows 2008 r2.
I have read this http://zmq503o1.wordpress.com/2008/01/06/using-cisco-wcs-with-microsoft-ias/ and done the same.
I dont't agree with "on the "Encryption" tab and clear all the checkboxes except "No encryption" - wants an encryption connection but this didn't work till in user's properites in AD permit "Reversible encryption". This is not what that I want. Would I need to generate ssl-cert for the wcs as wroted this?http://www.cisco.com/en/US/docs/wireless/wcs/7.0MR1/configuration/guide/hard.html#wp1042471
or doing smth else? thx

Camera is only supported for use with CUVA. Any other application attempting to utilize the camera is not tested and is not supported.

My itunes on a windows 7 pc with dsl connection will not connect with the itunes store

my itunes on a windows 7 pc with dsl connection will not connect with the itunes store. Any suggestions about why not or how to get it to connect?

After reading the whole post, I still don't capture the exact error message or code from it when you failed to install Office 2013.
The only clue is that "bootstrap loader error" ...
It seems that you want to upgrade Office 2007 to new Office 2013, by default, we could complete the uninstall previous Office version and install the new Office in the installation wizard.
At this point, if you get the install source through CD or other media. I recommand that we copy/paste the installation to local drive. Then turn off all of anti-virus and firewall, begin to setup in
Windows clean boot mode.
Please use a setup log to troubleshoot setup problems in Office if the installation problem still occurs.
http://support.microsoft.com/kb/826511/en-us
Tony Chen
TechNet Community Support

Cisco 2500 with DSL

Similar Messages

Maybe you are looking for