Cisco 2504 Management Via Wireless
I have a 2504 connected via a 2960S switch to an ASA5505.
Wireless is working well - wireless clients get their IP addresses from the 2504 and wired clients from the ASA (different ranges from the same subnet).
One issue though is I cannot access the web interface of the 2504 when connected to wireless, only wired. Everything else is accessible on wireless and I can ping the management address of the 2504 but the page fails to load in a browser.
I've had a look for an obvious setting but can't see one - am I missing something.
Thanks
HI,
First you must enable the management over wireless:
Via GUI:
Management > Mgmt Via Wireless page and check the Enable Controller Management to be accessible from Wireless Clients check box.
Via CLI:
config network mgmt-via-wireless enable
Regards
Dont forget to rate helpful posts
Similar Messages
-
Disabling Management via Wireless - is there any point?
Hey guys.
Firstly, yes, I do know that allowing management of controllers over an unsecured WLAN is a bad idea (although even that would be SSL-secured by default, but open to brute-forcing I'd guess).
Secondly, let's assume that Management via Dynamic Interfaces is disabled too (why anyone would want to enable that is a bit beyond me too?).
This 1 little tickbox manages to justify an entire page in the GUI, so it definitely looks pretty darn important!
The problem is that in a multi-controller environment the only controller that knows you're connecting over wireless is the one that you're connecting through. Any other controller will be happy to accept the management connection on it's management interface address because it sees it as coming from the wired network. To prevent this from happening I think you could do either of two things...
1) Apply a CPU ACL that blocks the client IP ranges, which will work equally well for wireless and wired-side connections, i.e. it's the equivalent of the "management via wireless" setting but works for all controllers simultaneously. You'd have to remember to keep this updated though if ever your WLANs and client ranges change.
2) Put the management interfaces of all controllers in an isolated management VLAN (which will potentially complicate all your supporting services access, e.g. DHCP/RADIUS/etc.). That'll stop the undesirable "wired" access on the n-1 controllers and then the mgmt-via-wireless will take care of the wireless access to the other 1 controller.
So the setting seems rather pointless on it's own in anything other than in a single-controller environment. I'm sure I've read somewhere that the controllers do tell each other about their current clients (for things like CCKM and rogue management), so wouldn't it be cool if this centralised awareness logic was applied to management connections?
What are the experiences out there with this feature? Is it generally seen as worthwhile, or does it really need some extra planning and possible augmentation via other features to be of any value?
In general, other than popular paranoia about wireless being "less secure" than wired access, what are the compelling reasons for denying management via wireless? As I mentioned above, even over a completely non-secured WLAN you'd still have SSL/SSH security if you configure your allowed management protocols right.
Thanks,
JustinYes "It makes the auditors happy" is definitely a good and valid reason.
I've just co-incidentally come across this in the 5.0.148 release notes:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn501480.html#wp234100
"Preventing Clients from Accessing the Management Network on a Controller
To prevent or block a wired or wireless client from accessing the management network on a controller (from the wireless client dynamic interface or VLAN), the network administrator should ensure that there is no route through which to reach the controller from the dynamic interface or use a firewall between the client dynamic interface and the management network."
That makes sense, but do many folks out there do it that way? Generally there's not much control between the management VLAN and the users' VLAN because the latter is usually where the wireless-supporting services reside. -
Management via wireless after H-REAP config
Hi,
Before I turned on H-REAP, created dynamic interfaces and did all the trunking to the AP's I could https to our controller on the management interface from the wireless network. After I put the config in place for the new SSID's, H-REAP etc.. I can't get to it from the wireless network. I can get to it from the local LAN. Any ideas??
Thanks.Hi Mike,
I'm trying to understand your question here ... If you have H-REAP enabled, you are UNABLE to HTTP/HTTPS into the WLC even when "Mgmt Via Wireless" is ticked (enabled)? What firmware are you using?
I am asking because I am using 5.2.178.0 and Cisco has confirmed that there is a bug (CSCsz06335). With "Mgmt Via Wireless" is ticked (enabled) the bug ALLOWS you to manage the WLC via Wireless.
This problem is only evident in the 5.2.178.0 version.
According to Cisco TAC, a new firmware should be made available by early June 2009.
Hope this helps. -
4404 wireless lan controller managment via wireless clients
I am having an issue managing a 4404 wireless lan controller via wireless clients.
I have checked the box "enable controller management to be accessible from wireless clients" under management. For some reason that does not seem to fix the problem (page cannot be displayed). I cannot ping the controller by IP but other devices on the same subnet respond. Everything else works fine.
I CAN manage the controller when plugged in a wired connection.
When I do a route print it is identical wireless or wired. The route simple points to my interface. If I modify the route on my computer to actually point to our gateway instead of the interface then everything works. But why should I have to do this only for my wireless connection and not my wired to manage this box?Thanks for the info. I narrowed the problem down to an ARP issue.
In order for me to connect to the controller, I run a batch file that creates a static ARP entry on my laptop. I don't have to do this for any other device except the controller. Not sure what the underlying cause is, but that works as a workaround right now. -
Monitoring Cisco UCS Manager via HP System Information Manager 7.1 (SIM)
I am working with a customer to configure HP System Information Manager 7.1 (SIM) to monitor their Cisco UCS Manager.
The customer is looking to monitor the following:
- CPU Utilization on manager, blades, servers, etc...
- Memory utilization
- Network utilization
- System inventory
Alerting is needed for the following:
- Hardware failures: memory, power supply, drive, etc...
- Predictive failures
- Alert messages
I have the list of all the MIBs provided by Cisco but an having the following issues while loading them into HP SIM.
While loading MIB "CISCO-UNIFIED-COMPUTING-TC-MIB" I get the following error message:
Line 128: Error defining object: expected a label, found reserved symbol {
Line in MIB: SYNTAX Gauge32 {
Guage32 is imported from SNMPv2-SMI MIB
To get past this error I found a version of the MIB that removes all the textual conventions that where causing errors. I have attached the fixed MIB file to this discussion. With the fixed version of the MIB installed in SIM everything compiles and installs except the following two MIBS. CISCO-UNIFIED-COMPUTING-NOTIFS-MIBCISCO-UNIFIED-COMPUTING-CONFORM-MIB Questions:
1. Is there any way to get the CISCO-UNIFIED-COMPUTING-TC-MIB MIB to install correctly into HP SIM?
2. Is my MIB load order setup correctly?
3. Has anyone had success getting HP SIM to monitor and alert for Cisco UCS manager?
MIB Load Order:
SNMPv2-SMI
SNMPv2-TC
SNMP-FRAMEWORK-MIB
RFC1213-MIB
IF-MIB
CISCO-SMI
CISCO-ST-TC
ENTITY-MIB
INET-ADDRESS-MIB
CISCO-UNIFIED-COMPUTING-MIB
CISCO-UNIFIED-COMPUTING-TC-MIB
CISCO-UNIFIED-COMPUTING-FAULT-MIB
CISCO-UNIFIED-COMPUTING-NOTIFS-MIB
CISCO-UNIFIED-COMPUTING-AAA-MIB
CISCO-UNIFIED-COMPUTING-ADAPTOR-MIB
CISCO-UNIFIED-COMPUTING-BIOS-MIB
CISCO-UNIFIED-COMPUTING-BMC-MIB
CISCO-UNIFIED-COMPUTING-CALLHOME-MIB
CISCO-UNIFIED-COMPUTING-CAPABILITY-MIB
CISCO-UNIFIED-COMPUTING-COMM-MIB
CISCO-UNIFIED-COMPUTING-COMPUTE-MIB
CISCO-UNIFIED-COMPUTING-CONFORM-MIB
CISCO-UNIFIED-COMPUTING-DCX-MIB
CISCO-UNIFIED-COMPUTING-DHCP-MIB
CISCO-UNIFIED-COMPUTING-DIAG-MIB
CISCO-UNIFIED-COMPUTING-DPSEC-MIB
CISCO-UNIFIED-COMPUTING-EPQOS-MIB
CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB
CISCO-UNIFIED-COMPUTING-ETHER-MIB
CISCO-UNIFIED-COMPUTING-EVENT-MIB
CISCO-UNIFIED-COMPUTING-EXTMGMT-MIB
CISCO-UNIFIED-COMPUTING-EXTVMM-MIB
CISCO-UNIFIED-COMPUTING-FABRIC-MIB
CISCO-UNIFIED-COMPUTING-FC-MIB
CISCO-UNIFIED-COMPUTING-FCPOOL-MIB
CISCO-UNIFIED-COMPUTING-FIRMWARE-MIB
CISCO-UNIFIED-COMPUTING-FLOWCTRL-MIB
CISCO-UNIFIED-COMPUTING-HOSTIMG-MIB
CISCO-UNIFIED-COMPUTING-IMGPROV-MIB
CISCO-UNIFIED-COMPUTING-IMGSEC-MIB
CISCO-UNIFIED-COMPUTING-IPPOOL-MIB
CISCO-UNIFIED-COMPUTING-IQNPOOL-MIB
CISCO-UNIFIED-COMPUTING-ISCSI-MIB
CISCO-UNIFIED-COMPUTING-LICENSE-MIB
CISCO-UNIFIED-COMPUTING-LLDP-MIB
CISCO-UNIFIED-COMPUTING-LSBOOT-MIB
CISCO-UNIFIED-COMPUTING-LSMAINT-MIB
CISCO-UNIFIED-COMPUTING-LS-MIB
CISCO-UNIFIED-COMPUTING-MACPOOL-MIB
CISCO-UNIFIED-COMPUTING-MAPPINGS-MIB
CISCO-UNIFIED-COMPUTING-MEMORY-MIB
CISCO-UNIFIED-COMPUTING-MGMT-MIB
CISCO-UNIFIED-COMPUTING-NETWORK-MIB
CISCO-UNIFIED-COMPUTING-NWCTRL-MIB
CISCO-UNIFIED-COMPUTING-ORG-MIB
CISCO-UNIFIED-COMPUTING-OS-MIB
CISCO-UNIFIED-COMPUTING-PCI-MIB
CISCO-UNIFIED-COMPUTING-PKI-MIB
CISCO-UNIFIED-COMPUTING-PORT-MIB
CISCO-UNIFIED-COMPUTING-POWER-MIB
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB
CISCO-UNIFIED-COMPUTING-PROC-MIB
CISCO-UNIFIED-COMPUTING-QOSCLASS-MIB
CISCO-UNIFIED-COMPUTING-SOL-MIB
CISCO-UNIFIED-COMPUTING-STATS-MIB
CISCO-UNIFIED-COMPUTING-STORAGE-MIB
CISCO-UNIFIED-COMPUTING-SW-MIB
CISCO-UNIFIED-COMPUTING-SYSDEBUG-MIB
CISCO-UNIFIED-COMPUTING-SYSFILE-MIB
CISCO-UNIFIED-COMPUTING-TOP-MIB
CISCO-UNIFIED-COMPUTING-TRIG-MIB
CISCO-UNIFIED-COMPUTING-UUIDPOOL-MIB
CISCO-UNIFIED-COMPUTING-VM-MIB
CISCO-UNIFIED-COMPUTING-VNIC-MIB
References:
ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html#_Toc303691433
http://www.hp.com/wwsolutions/misc/hpsim-helpfiles/simsnmp.pdfPlease post "debug ccsip messages".
Based on your debug you are getting "Cause No. 38 - network out of order."
You may want to bind SIP to an interface that the IP address is defined which Lync points to.
Chris -
2504 Management over a separate Port
Hello,
is it possible to Manage the 2504 Controller over a separate Interface.
Exmaple:
Port 1 is used as controller management interface (untagged) - AP's are connected to the same VLAN
Port 1 is used for Guest Traffic (VLAN 3 tagged)
Port 2 should be used to manage the WLAN Controller from the internal LAN. (tested with untagged, tagged, same issue)
with this Setup it is possible to ping the Port 2 IP-Address from the internal LAN but if you try to connect to the controller,
the Browser shows "Site not reachable".
I also enabled "Management via Wireless" but without success.
I also tried to add the "management" VLAN as tagged on the management Interface with the same effect,
the controller is not manageable from the internal LAN.
On 5508 WLAN Controller i have an similar setup, but with LAG Port enabled. There this works.
The only interface were i can manage the WLAN controller is from the management Interface.
i hope someone can help me
kind regards
MathiasYes, you need to drop in the CLI and issue this command
config network mgmt-via-dynamic-interface
BTW -- TAG EVERYTHING on the WLC.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin -
7.2.110.0 - Management from Wireless Issue
I'm sure this has come up before and I've had this problem for awhile just no time to check on it. So, with some of my 5508's, I can telnet and ssh via a wireless connection, but no https and the 5508 I'm working with now I can't do any of those despite Management Via Wireless option ok'd?
I know, and I've gotten better about the templates. But from an old cli commando, NCS (or gui period) is slow and cumbersome unless your doing a mass deployment of something. I like NCS over WCS in feel (okay, it's alittle prettier) but it's also slower then WCS imho. And although WCS/NCS gives you more options then say the WLC's gui, the WLC's CLI gives you more detail. Either way, the damn thing should work when you have it set to manage via wireless connection. It should be a like a switch/router, defaults to anyone unless you acl it, or a pix/asa, say management allowed from such and such subnet and mask, or wildcard it out. I'll tac it in my 'spare' time.
-
Hello,
I am wondering if this is possible, and how to execute.
We have a separate physical network for guest wireless access that we will be using a cisco 2504 controller and AP's. I wanted to manage the WLC from the corporate network, and wanted to have a management interface on our DMZ to allow 443 management from inside our corporate network.
I tried making the built in management interface on our corporate DMZ network, and another interface for the Guest Network, but I am unsuccessful:
Management port 1: 192.168.x.x
Dynamic interface port 2: 10.5.x.x
Once I enable Dynmaic AP management on the Guest network, I cant ping any devices on that network.
I also tried making a VLAN for the management network and another vlan for the Guest network and mapping them to the single built in management port, but I have been unsuccessful in that.Hi,
ip http server
ip http authentication local
ip http secure-server
username cisco password cisco.
HTH,
Bjornarsb -
E4200v2: Local Management Access via Wireless *ALWAYS* Enabled
I just found a slightly unsettling bug in the E4200v2 (running the latest firmware 2.0.36 build 126507).
Administration > Local Management Access > Access via Wireless ... set to DISABLED.
HOWEVER, when I attempted to access the web interface on a handy iPAD I had absolutely no problem getting through to the web interface (after providing username and passsword).
Limiting access to wired clients seems like a simple a prudent measure ... which is why this option is there for the paranoid among us.
This seems like a black-and-white bug. Comments welcome. Fix in the next firmware revisio even more welcome.It was mentioned in another thread that disabling wireless management does indeed disable http access over port 80. However, if you're using https access--which uses port 443, that access is not blocked. So for anyone who wants to disable wireless management access, you need to enable management access via http only, and then disable the wireless access. That combination will indeed work.
I have confirmed this on my own router and can now only manage via wired connections over http.
Strange bug/oversight! -
Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, GraciasHi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established -
Wi-Fi Installation in large property W/Cisco 2504
Hi,
I have an interesting job where i am having to fit a wifi network through a large property. I was advised to use the Cisco 2504 WLC and 9 x Cisco AIR-AP1142N access points.
I know that out of the box the AP's (in standalone versions) have the GUI enabled.
Not being completley up with CLI etc, is the WLC GUI enabled straight out of the box? if not, is it complicated to get it up and running? I'm pretty good at learning/understanding these things just as long as i have a rough idea of what to do!
Thanks in advance,
JoshThats great, Thanks steve.
I have the Controller (although AP's are still on order - out of stock ) but i have one final question before i start to set it up!
I'm looking at this guide: http://www.cisco.com/en/US/docs/wireless/controller/2500/quick/guide/ctr2504_q_s.html#wp34023 and it talks about Management interface. I presume the management IP address would be the fixed ip of the controller if you like.
So if i had a network with a DHCP server. The Router/Server was 192.168.2.1 and the DHCP range started from .10, i could set this to be 192.168.2.2 with the router of the management interface to be .2.1. I then could set the VLAN id to be 0 as i don't need a seperate managment lan (it's only for a house afterall, and if i lock it down with passwords it should be fine).
With the Management Port, i presume that can be the port that connects into the main PoE Switch, similalry the Management DHCP server would be 192.168.2.1?
Virtual Gateway IP address i guess is irelevant as there will be no mobility group?
And DHCP bridging, like on any other wifi system/AP would be 'No' as the Router will be dealing with all DHCP requests?
Thanks again for your fantastic help so far!
Josh -
Help required to implement Cisco 2504 WLC and 1042 Access Points
Hi,
My name is Vidya Sagar. I am new to Wireless technology. We are planning to implement Wireless in our office. I have given the requirements below. Kindly go through the details and let me know how to start.
We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.
I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
Please give me a implementation plan to do this. I would like to use LDAP or ACS for authentication purpose.
Regards,
Vidya SagarLets just do this simple first before you start using ACS as that will require a certificate installed on the ACS for using PEAP.
So first off, the WLC we will say is in vlan 10. When you are going through the startup wizard, make sure you define the vlan tag to 10 on the management interface. Make sure your virtual interface is an IP address that is not routed in your network, like an out of band IP.
Make sure the WLC time is correct or use NTP!!!!
Now you should be able to http or https to the WLC. I would upgrade the code to v7.4 and install the FUS image. Please reference this link for the upgrade procedure. You don't have to upgrade now... I would wait till you get everything working first.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74.html
Now I would connect the APs on the same vlan as the WLC for now. Make sure there is dhcp on that subnet. Once the APs have joined, then you can move them to any subnet you want. Since you don't have many APs it would be okay to leave them in the same vlan as the WLC management or out them on any other vlan you choose. The APs will be connected to an access port NOT a trunk port!!!!
The WLC will need to be connected on a dot1q trunk port only allowing vlans 10,100,116,121. The 2504 running v7.4 will support LAG (etherchannel). Any ways, your switch port should look like this for example only
Interface gigabit1/0/1
description WLC2504
switch port trunk encapsulation dot1q
switchoort mode trunk
switch trunk allowed vlans 10,100,116,121
spanning-tree portfast trunk
channel-mode group 10 mode on << only for v7.4 if you use lag
Don't connect all four ports right now, just port one!!!!
Your Guest vlan, you will need to create an ACL to block traffic from accessing the internal network. You might want to allow dhcp and DNS bit I would leave it open first until you can verify everything is working.
Now on the WLC you need to create a dynamic interface for vlan 100, 116, and 121. If you click on the Controller tab in the GUI and click on interfaces on the left hand side, that will take you to where you can add/delete/modify your interfaces. When creating these interfaces, make sure you add the dhcp server IP address for the primary and or backup.
Now that you have your dynamic interfaces created, its time I create your SSID. Now click on the WLAN tab on the GUI and click on WLAN and then on the too right select Create New and then click go. Select WLAN on the drop down menu and then for the profile name I would use the SSID name also for simplicity.lean e the WLAN id to 1 for this and 2 for the next and so on. After defining these and clicking Apply you can now define your SSID. On the General tab, enable the status and leave the radio policy to all for now, you can decide later what you want to use. Choose your interface you wan to place this SSID on and enable Broadcast SSID for now and leave everything else alone. Now click on the Security tab and on the layer 2 Security, leave it at WPA + WPA2, only check WPA2 Policy and for WPA2 encryption choose AES only. Now go to the bottom of that screen and choose PSk. We will do pre shared key for now so you get to understand the setup and make sure everything is working first. Now on the PSK format, choose ASCII and put your pre shared key in the input box. Make this simple to for testing. You don't want to put in symbols or anything like that. When you are don with that, check apply on the top right and test.
Now you can repeat this with your other SSIDs just to test. Your guest network you can leave open for now to test open authentication.
Here are some links for the WebAuth feature:
https://supportforums.cisco.com/docs/DOC-13954
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080b1a506.shtml
Now if you want to use ACS with PEAP, here is some links for that:
https://supportforums.cisco.com/videos/2499
http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080bd1100.shtml
https://www.google.com/url?sa=t&source=web&cd=8&ved=0CFQQtwIwBw&url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DWk_bRdmsQlA&ei=_BEyUeCYM8TdqAHHsICAAw&usg=AFQjCNF8PiVBQK1Kipb4j8AzD153bKtmgA&sig2=smHhNVmCr2of2NzbnDhGmw
Well that is it, hopefully you can get the wireless up for testing and verifying everything works!
Sent from Cisco Technical Support iPhone App -
100% Noob - Need Help for basic setup of Cisco 2504 and 1600 AP
Hello,
I am completely noob in (cisco) networking.
I have to setup a basic but secure wireless network.
I have a cisco 2504 and 2 APs 1600 + a random switch
I have 4 ports on the controller.
I want to keep the 1st port on the network for the controller management, plug my internet box on the 3rd port, and my switch on the 4th port. Then the AP will be on the switch.
I am able to make something working when everythings are plugged on the switch, plugged in the first port (default management port).But this is not what I want.
First thing, Is that possible ?
1st port : office network
2nd port : empty
3rd port : Internet Box
4th port : Switch + all APs
Then, if that is possible, how should i configure the controller to make that work ? I am completely lost in the menus.
I dont need a perfect configuration, just something simple and working.
1 SSID, 10 DHCP addresses, block wireless users trying to go on the office network.
If anyone could help my doing that, It would be very nice.
Thank you.You basically need two SSIDs one for corporate users and second for guests .check the link with step by step config and brief details .
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/70937-guest-internal-wlan.html -
Can't connect via wireless wrt160n ver 1
I am using a wrt160n version 1 with the latest firmware. The internet is via cable modem which works fine and the computer i am writing this message with is connected to the router via ethernet. The problem comes when i try to connect another PC (mine, this is my mum's) via wireless. I am using windows 7 and it says after 2-3 seconds Windows cannot connect to the wireless network. The signal strength is showing excellent with all bars full (and i have checked this by moving the router to within 10 cm of the wireless aerial of the computer that fails to connect and nothing changes). Occasionally it will connect, but the speed is awful and it wont reconnect when windows is restarted. I don't know why it connects occasionally. When i say occasionally i mean after 100 or so attempts, but this is no guarentee. I have tried multiple aerials including one with an insulated cord, so you can put the aerial far away from your computer, so i don't think theres a problem with interference.
I have tried:
resetting and reprogramming the router, including factory reset
re-aplying the latest firmware
deleting the connection profile in windows
resetting my computer and the network adapter (my wireless card)
3 other network cards
moving my computer, the router, the aerial
changing channel
formatting the computer that cant connect, fresh installing windows
cursing and praying.
In the network diagnostic details from windows 7 auto-repair thingy, it seems that pre-association is working, but actual association is failing. The error code given is "0x00038002" next to association. Further down it also says that it failed to recieve a response from the access point or router. The funny thing is, everything was working fine a few weeks ago with the exact same hardware and software. Nothing has changed except my ability to connect.Well I think (fingers crossed) mine is working properly now... so far so good.... i have a happy teanager again... she has internet.... ha-ha
Default reset on WRT
Firmware update to Version 3 on the WRT (that was a pain in the butt... )
default reset on WRT (AGAIN)
reconfig..../set-up .etc....
Had to adjust the settings on the firewall of the Win7 laptop to allow Cisco Pure networks and Network Magic to enter the wall...
As much as I didnt want to... I also installed Network Magic on both computers and it really walked/guided me through alot of the issues and fixed most of the items by itself... Saved info to USB and uploaded to Win7 laptop... and it is working fine now......
Lets see if it last and works smoothly.... -
Accessing iphoto library on external drive via wireless
I'm running out of room on my macbook so I moved my iphoto library to an external drive (after reading other posts on how to accomplish this, copied to the external drive and connected without a problem). However, i'm accessing the external drive wirelessly from my airport extreme and now iphoto is painfully slow - it takes several seconds for each photo to resolve properly. Any suggestions for the best way to manage? Do i need to keep older photos in a library on the external drive and a library for more current ones i want to access regularly on my local? I don't think i want to have multiple libraries but the performance this way is driving me crazy.
Welcome to the Apple Discussions.
A strong warning: If you're trying to edit the Library (that is, make albums, move photos around, keyword, make books or slideshows etc.) or edit individual photos in it via Wireless be very careful. Dropouts are a common fact of wireless networking, and should one occur while the app is writing to the database then your Library will be damaged. Simply, I would not do this with my Libraries.
A wired connection is the best way to have your Library on an external.
Regards
TD
Maybe you are looking for
-
When I make a Book using Aperture 3 and print a PDF proof version, all images that have been modified within Aperture are distorted in PDF form. All other images appear ok.
-
ALSA: Sound not working when webcam is plugged in. [Solved]
I'm using the out-of-the-box sound setup (ALSA, nothing else). My sound card setup (including the USB webcam with mike): mrkline $ cat /proc/asound/cards 0 [VX5000 ]: USB-Audio - Microsoft LifeCam VX-5000 Microsoft Microsoft LifeCam VX-5000 at usb-00
-
Previous Purchase in Library as an 'error' file, unable to redownload.
I have several television shows that I have purchased. They are in my Library as icons. When I click on them to try and play, the error message comes up that "cannot find the original file'. When I look at the items as a list, there is an exclamation
-
Hey guys i m trying to post some Sales order Idoc's to CRM system from a SOAP client but i dont know which webservice to use. do you guys know any webservice which i can use to post IDoc's to CRM and then send the response back to the webservice. i m
-
Background colour not matching jpg
Please help if you can? My website has the background colour set as d6d3cd, and I have a JPG placed in the page with the same exact colour (it's an object on top of the colour). The problem is when I load the page in a browser there is a slight colou