Cisco 2801 and VIC2-2E/M Card

Hi Experts,
One problem with my cisco 2801, when I have inserted the E&M card it is not supporting on the slot. The output of show diag is as attahced.
IOS is : c2801-ipbase-mz.124-1c.bin
Any help would be appreciated..
Thanks,
Hardik..

You need a voice capable IOS feature set. The minimum is IP Voice for this card. Please see the following link for confirmation.
http://www.cisco.com/en/US/products/hw/modules/ps5365/products_data_sheet0900aecd801c595e.html
Hope this helps. If so, please rate the post.
Brandon

Similar Messages

Cisco 2801 and 2851

We have a 2801 with an existing T1 card. We would like to replace with a 2851.
Will the T1 card on the 2801 work on the 2851?

Perform the "show diag" command instead. It will show you the part number of the T1 card.
For example:
WIC-1DSU-T1 (supported in the older 2600 series)
WIC-1DSU-T1-V2 (supported in the newer 2600xm and beyond)
WIC-1T
WIC-2T
VWIC-1MFT-T1
VWIC-2MFT-T1
VWIC2-2MFT-T1
You could also use the "relevant interfaces and modules" link under the 2800 series routers.
http://www.cisco.com/en/US/products/ps5854/products_relevant_interfaces_and_modules.html

Strange behavior with Cisco AP and Intel 3945 wireles card

Hi,
I have an interesting problem with an Intel 3945 A/G card, and my cisco APs.
1. Given:
Cisco 1100 and 1200 AP running IOS 12.3.8-JEA
Two laptop, one with Intel 2200 MPCI Card, the other with Intel 3945 MPCI Card
Microsoft AD with IAS radius server
a. 1 SSID with Simple EAP-TLS configuration Enterprise WPA/TKIP, no vlans, broadcast SSID. both card associate correctly and operate normally.
b. 2 SSID, 1 with simple EAP-TLS configuration Enterprise WPA/TKIP (broadcast), and 2nd SSID Open/No encryption/No authentication (not broadcasted), both cards associate correctly and operate normally.
c. 2 SSID, 1 with simple EAP-TLS configuration Enterprise WPA/TKIP (broadcast), and 2nd SSID WPS-PSK (not broadcasted), both cards operate normally.
Now it gets interesting:
c. 2 SSID, 1 with EAP-TLS/WPA Enterprise on its own VLAN 102, 2nd SSID Open/No Encryption/No authentication on a separate VLAN 105, VLAN 1 is used for admin and radius backhaul to IAS.
If both SSID are broadcasted via mbssid guest-mode both Intel cards work as expected
If neither SSID are broadcasted, both Intel cards work as expected
If either SSID is broadcasted via normal guest-mode command, the Intel 2200 associates and works correctly, but the Intel 3945 refuses to assocate to the AP.
Has anyone heard of side-effect?
Alan

I'm seeing a similar issue with the 3945 right now. However in my example the following is the case;
APs are 1200 series IOS upgraded running 802.11b interfaces only. There are multiple SSIDs NONE of which are broadcasting.
We've got a few different client types. The Cisco CB21ABG cards are fine, as are the Intel 2200 and 7920 phones. It's only the 3945 that has a problem and it's running Intel's 10.5.1.68 driver which is the latest. I'm considering downgrading it to an older driver.
Anybody got a definate fix for this Intel card???

What's wrong? Verify and compare Cisco 2901 config after loading old config from Cisco 2801

Hi Cisco Community / Friends,
I am new to this site though I have cisco account for many years. I am a CCNA ,I passed my certification on January 2013 I seldom use and utilized my skills on networking becuase of my type of work. I am Project Eng'r working in a System integrator company . Anyway, I would like to ask assistance on the configurations of my Cisco router for this gov't projects.. Here's the situation.
We have a new project for the VSAT Comm'n of Coast Watch Station , The VSAT was installed 7 years ago. The VSAT was only used for a year by this Gov't agency because of subscription issue. Now, they wants to revive and use their VSAT facilities for the Coast watch monitoring. Now, some of this routers are working up to now and for some site are already defective so I need to replace the old 2801 router with a new equivalent model which is Cisco 2901. My plan was just to load the old config into the new Cisco 2901 router. However, after loading it to the new router, I am a little worried because I've got some errors received. I load the old config by copying the old files, edit it in notepad, and load the config using Secure CRT (terminal emulator). When I copy the old config of cisco 2801 to new router cisco 2901 , below are the command not recognized on Cisco 2901. What's wrong ? What are these commands for?
Appreciate your comments and help on this matter.. Thank You very much
Note: I Attached the original config from Cisco 2801 and the other file is the config after I load the config file to Cisco 2901.
(Errors see below)
CWS_4_Pandami(config-erm)#mmi polling-interval 60
                         ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi auto-configure
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi pvc
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#mmi snmp-timeout 180
                                                        ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-if)#interface GigabitEthernet0/1
CWS_4_Pandami(config-if)# description ===CWS4 SAT Modem===
CWS_4_Pandami(config-if)# bandwidth 256
CWS_4_Pandami(config-if)# ip address 192.168.42.1 255.255.255.0
CWS_4_Pandami(config-if)# duplex auto
CWS_4_Pandami(config-if)# speed auto
CWS_4_Pandami(config-if)# priority-group 1
                                                    ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config)#access-list 100 permit ip any any dscp cs5
CWS_4_Pandami(config)#priority-list 1 protocol ip high list 100
                          ^
% Invalid input detected at '^' marker.

Hi
From Cisco's website:
The Modem Management Interface (MMI) is software that enables auto-provisioning for the Cisco 827 routers. The MMI uses a fixed PVC to communicate with the Proxy Element (PE) residing on the digital subscriber line access multiplexer (DSLAM). Using MMI, the Cisco 827 router updates the running image and downloads the prescribed configuration using a configuration file or configuration values in a provisioning information database.
The customer premise equipment (CPE) can be automatically configured using the Cisco DSL CPE download, but it can be configured only with the image provisioning feature.
So because this is your device, you don't want to use MMI anyways.
And "priority-list" is QoS. Probably that QoS-command is old and removed, because now QoS is configured using class-maps and policy-maps.

How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

Hello
I'm looking for information on how to install 2 newly purchased cards and keep running into dead links. The cards I bought are for a CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco router:
vic3 2fxs/DID and a vic2 2fxo.
I keep finding documents on how to install these cards but all links are dead and leading to nowhere.
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
The 2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco 2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco router.
NOTE: I've never installed these cards and am not sure if:
Does my ios support both of these cards?
and which slots do I install those in the router.
I have 4 slots like this:
slot 0: This slot only accepts VIC's ***This could be used for the vic3 2fxs/DID card correct?
slot 1: Nothing written here ****What can i install in this slot?
slot 2: This slot only accepts VIC's and WIC's ***If I buy a WIC and install here which other slot can i install my VIC2-2FXO card in ?
slot 3: Nothing written here ***What can i install in this slot?
Any chance someone can help me out with this.
Thanks very much

Ok
I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
Thanks

Vic2 - 2FXS Card in 2801 and modem / fax usage

Hi,
I have a Cisco 2801 running c2801-advipservicesk9-mz.124-9.T.bin
It has 2 VIC2-2BRI-NT/TE cards, 1 VIC2-2FXS. And a PVDM2-8 and a PVDM2-16 as DSP's.
I am trying to get a modem working on a FXS port, but one way or the other it's just not comming together.
I do have a propper PSTN line when I use an analogue phone, but when I try to hook up a modem nothing or sometimes a crappy 2k4 connection.
What am I missing here, I thought by putting in enough DSP's in the router and a FXS card and BRI cards this should work.
Nothing fancy configured on the voice ports (first 4 are BRI last 2 FXS)
voice-port 0/0/0
compand-type a-law
cptone CH
voice-port 0/0/1
compand-type a-law
cptone CH
voice-port 0/1/0
compand-type a-law
cptone CH
voice-port 0/1/1
compand-type a-law
cptone CH
voice-port 0/2/0
cptone CH
voice-port 0/2/1
cptone CH
Can anyone tell me what to do to get a modem working propperly on this FXS ports ?

You may want to try adding this command:
voice service voip
modem passthrough nse codec g711alaw

Cisco 2811 Router with 3 ADSL card and load balancing

Dear All,
I have few queries:
1. Does Cisco 2811 Router support 3 ADSL card?
2. We are the ISP. I want to do load balancing with 3 dsl
line on Cisco 2811 Router.
Please send me the linke for this configuration.
Thanks/Regards
Atul

hi
In 2811 you have 4 HWIC and 1 NME you can install 1-port ADSL WAN Interface Cardon the HWIC slots.
Also just enable 3 default (equal cost) routes towards the interfaces which will take care of the load balancing.
if you need more info and inputs do post out with ur requirements along with network topology in place at present..
regds

VPN between RV042 and Cisco 2801

HI
Kindly help me out. I'm configuring a p2p vpn between a cisco 2801 with IOS 12.3 and a linksys RV042. I'm getting following error on Linksys and Cisco respectively.
[Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
Dec 19 02:40:42 2011
     VPN Log
    Received informational payload, type NO_PROPOSAL_CHOSEN
dst             src             state               conn-id     slot    status
x.x.x.x       x.x.x.x   MM_NO_STATE          0        0       ACTIVE
Below are my config:
Linksys RV042:
Keying Mode: IKE with Preshared Key
Phase1 DH Group: Group2
Phase1 Encryption: 3DES
Phase1 Authentication: MD5
Phase1 SA Life Time: 28800
Perfect forward secrecy : enabled
Phase2 DH Group: Group2
Phase2 Encryption: 3DES
Phase2 Authentication: MD5
Phase2 SA Life Time: 28800
Preshared Key: xxxxxx
Cisco 2801:
crypto isakmp policy 11
encr 3des
authentication pre-share
group 2
lifetime 28800
crypto isakmp key xxxxxx address xxxxxx
no crypto isakmp ccm
crypto ipsec transform-set STRONGER esp-3des esp-md5-hmac
crypto map myvpn 10 ipsec-isakmp
set peer xxxxxx
set transform-set STRONGER
set pfs group2
match address 103
interface FastEthernet0/0
ip address 10.0.0.56 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
no mop enabled
interface FastEthernet0/1
ip address xxxx xxxx
ip nat outside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
crypto map myvpn
ip nat pool branch xxxxxx xxxxx netmask 255.255.255.240
ip nat inside source route-map nonat pool branch overload
access-list 103 permit ip 10.0.0.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 110 deny   ip 10.0.0.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 110 permit ip 10.0.0.0 0.0.0.255 any
snmp-server community public RO
route-map nonat permit 10
match ip address 110
Rgards
SAM

Hi,
It looks like you are using the default hash for the crypto isakmp policy and that your connection is failing on the phase 1 negotiation. The default hash on the crypto isakmp policy is sha. On the 2801 try adding hash md5.
crypto isakmp policy 11
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
Let me know if that helps.
Thank you,
Jason NIckle

Cisco 2801 Auto Attendant

hello
I have 2 Cisco 2801 running CME 4.3 and will be converter to SRST Routers, but they''ll have T1 card, because they used to has FXO card with 4 lines now they will have T1, but I wonder witch solution for auto attendant should I have for those routers especially the Unity Express.
Thanks

Before switching to CM, think twice, because you will gain a lot of complications, consts, and loose nice features and flexibility if you do that.

No service password recovery command on cisco 2801 router

HI,
we have a cisco 2801 router in class which has a disabled pasword recovery. We tried almost everything, we cannot get into ROMmon and the break sequence dosent work in any program (hyper terminal, putty, teraterm pro). We dont have any idea how to solve this problem.
Here is the log from hyperterminal:
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2004 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c2801 processor with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
PASSWORD RECOVERY FUNCTIONALITY IS DISABLED
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xd49718
Self decompressing the image : #################################################
######## [OK]
--- TRIED BREAK SEQUENCE HERE but nothing happens ---
Smart Init is enabled
smart init is sizing iomem
ID            MEMORY_REQ         TYPE
                0X003AA110 public buffer pools
                0X00211000 public particle pools
0X0013          0X00035000 Card in slot 1
                0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 7692663 bytes to IO Memory.
PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, 2801 Software (C2801-IPBASE-M), Version 12.4(1c), RELEASE SO
FTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 26-Oct-05 08:42 by evmiller
Image text-base: 0x6007ECA0, data-base: 0x61480000
--- TRIED BREAK SEQUENCE HERE but nothing happens too ---
Port Statistics for unclassified packets is not turned on.
Cisco 2801 (revision 6.0) with 114688K/16384K bytes of memory.
Processor board ID FCZ102422KK
2 FastEthernet interfaces
2 Low-speed serial(sync/async) interfaces
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
Press RETURN to get started!
Thanks for help!

I usually suffer from the same issue, but what works for me everytime is the other method that simulates break sequence. Can't find the documentation for it but this is how it goes:
Set the serial connection as follows in Putty:
Baud rate 1200
1 stop bit
8 data bits
no parity
no flow control
Turn off your router, then turn it back on and immediately press the spacebar for about 10-15 seconds. All you'll see is giberish. After that reset your console connection settings to the usual 9600 baud rate, and you'll find yourself in rommon mode.

Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T

Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
I am having trouble making outgoing call or answering incoming call.
When I try to call out from my IP 7961 phone, it fails with the message "unknown number".
For incoming call, it rings but when I pick up the call nothing happens,
Put the receiver back on hook, the phone carries on ringing. I am in UK
and just trying to set up test system with one analogue line. Any help will
be most appreciated. My config of the 2811 router is posted below. All calls ineternally works fine.
Thank you for your help.
hostname Test-CME
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1 10.10.10.10
ip dhcp excluded-address 10.139.139.1 10.139.139.10
ip dhcp pool host
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
option 150 ip 10.10.10.1
ip dhcp pool data
network 10.139.139.0 255.255.255.0
default-router 10.139.139.1
dns-server 10.139.139.5
voice-card 0
no dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
sip
header-passing
registrar server expires max 3600 min 3600
interface FastEthernet0/1
no ip address
no ip mroute-cache
duplex auto
speed auto
no shut
interface FastEthernet0/1.2
description ** Data VLAN **
encapsulation dot1Q 2
ip address 10.139.139.1 255.255.255.0
interface FastEthernet0/1.3
description ** Voice VLAN **
encapsulation dot1Q 3
ip address 10.10.10.1 255.255.255.0
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
tftp-server flash:S00104000100.sbn
tftp-server flash:TERM41.7-0-3-0S.loads
tftp-server flash:term61.default.loads
tftp-server flash:term41.default.loads
tftp-server flash:CVM41.2-0-2-26.sbn
tftp-server flash:cnu41.2-7-6-26.sbn
tftp-server flash:Jar41.2-9-2-26.sbn
tftp-server flash:term70.default.loads
tftp-server flash:term71.default.loads
tftp-server flash:cnu70.2-7-6-26.sbn
tftp-server flash:Jar70.2-9-2-26.sbn
tftp-server flash:TERM70.7-0-3-0S.loads
tftp-server flash:CVM70.2-0-2-26.sbn
control-plane
voice-port 0/3/0
connection plar opx 202
caller-id enable
dial-peer voice 1 pots
incoming called-number .
destination-pattern 9T
port 0/3/0
telephony-service
load 7914 S00104000100
load 7941 TERM41.7-0-3-0S
load 7961 TERM41.7-0-3-0S
load 7970 TERM70.7-0-3-0S
max-ephones 20
max-dn 40
ip source-address 10.10.10.1 port 2000
calling-number initiator
service phone videoCapability 1
system message MKC CME
url services http://10.10.10.1/voiceview/common/login.do
url authentication
http://10.10.10.1/voiceview/authentication/authenticate.do
time-zone 21
date-format dd-mm-yy
voicemail 600
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
moh music-on-hold.au
web admin system name admin secret 0 test
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
secondary-dialtone 9
create cnf-files
ephone-dn 1 dual-line
number 201
label 201
description Sarah
name Sarah
ephone-dn 2 dual-line
number 202
label 202
description Vitthal
name User2 Vitthal
ephone-dn 3 dual-line
number 203 secondary
label 203
description Neil
name User3 Neil
ephone 1
video
username "user1" password 201
mac-address 0018.18EE.947F
type 7961 addon 1 7914
button 1:1
ephone 2
video
username "user2" password 202
mac-address 0018.18BB.B973
type 7941
button 1:2
ephone 3
video
username "user3" password 203
mac-address 0018.1885.6BA2
type 7970
button 1:3

Hi
Please find enclosed debug attachment for voice ccapi and ephone. First, I called from outside. Extension 202 rings but when I answered on extension 202 nothing happens. Replace the rceiever and the pone starts ringing again.Second step. I tried to call out by dialing 9 and then number but after a while phone displays unknown number.
Thank you for your help.
Vitthal

Cisco 2801 (Voice Gateway + CUE)

Hi there,
I got two questions:
1) When I try to login to Cisco 2801 I get the following lines: (I've already changed the default username and password!)
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username "cisco"
with the password "cisco". The default username and password have a privilege level of 15.
Please change these publicly known initial credentials using SDM or the IOS CLI.
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to use.
For more information about SDM please follow the instructions in the QUICK START
GUIDE for your router or go to http://www.cisco.com/go/sdm
2) Is there any configuration example to configure CUE on Cisco 2801 (AIM Module)?
Thanks.

Hi there,
1. The lines you reference are the default message of the day banner on the ISR routers. To remove the message, go into configuration mode and enter the command "no banner motd"
2. Here's a sample configuration of configuring CME and CUE. The sample configuration should work on your 2801 ISR router. Feel free to give it a try and post here is you run into any issues or need clarification on anything.
http://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_configuration_example09186a008037f2a9.shtml
Hope this helps.
Regards,
Michael.

WIC1-AM on Cisco 2801 Routers malfunctioning

Hi, I wish i will find a permanent solution for my issue which i face for last 8 months.
I had purchased 5 Cisco 2801 routers to setup in our network which involves
branch offices and the head office. The branch offices are in different cities. We purchased these rounters with one WIC1-AM for each router keeping in mind to have a backup dialup line once the main link is down. The problem area is here. We have tested the Routers with
configurations for backup line in our Head office, it worked fine. But when we send them to some of the branch offices, it started malfunctioning. The dialup WIC plays crazy with us.Sometimes works for 10 minutes, and disconnects. One of the branches, the WIC never got up!!.
Only two branches is properly working now with backup line in WIC-1AM. We have tried the same configurations on the affected routers too, but the result was not hopeful.
On the same telphone lines, we were (and still) using zyxel prestige 100 MH router and is working perfectly without any single problem to note!
Thanks for any light to shed on this!

Hello Mohamed,
can you post what you have configured on the router(s) that are working ok ? Also, which IOS version are you running on the routers that do not work ? Can you post the outbut of 'debug modem' ? This should give an indication of what is happening...
Regards,
GP

Cisco 871 and 881 routers PCI Compliant?

do you know if the Cisco 871 and 881 routers are PCI complaint for 2015 and if not, are they able to be updated to be PCI Compliant?
thanks,
I am a Franchisee for a pizza chain and they are stating the routers will not be compliant with the new credit card PCI standards.

Any router can be PCI complaint as long you follow the PCI guide to harden the router and apply the correct filters.For example; one of the PCI requirement is to disable telnet access to the router and only use SSH. So, this can easily be accomplished if you have the right IOS with security installed.
HTH

Can I add these two VWIC2 modules on a Cisco 2801?

Hello all,
Can I add both of these modules on a Cisco 2801 running 12.4(3h)?
VWIC2-2MFT-T1/E1
and
VWIC2-2MFT-G703
Thank you,
Nadeem

Thanks for the response, but it doesn't really address my question(s).
Obviously, if I were buying memory for the old iMac, I would buy the same speed as the one already in it. However, I am not buying memory, I already have this spare faster memory. Let me split the question in two:
1. Will the faster memory work on the slower iMac?
2. Can the faster memory damage the slower iMac?

Cisco 2801 and VIC2-2E/M Card

Similar Messages

Maybe you are looking for