Cisco 2811 Router with 3 ADSL card and load balancing

Dear All,
I have few queries:
1. Does Cisco 2811 Router support 3 ADSL card?
2. We are the ISP. I want to do load balancing with 3 dsl
line on Cisco 2811 Router.
Please send me the linke for this configuration.
Thanks/Regards
Atul

hi
In 2811 you have 4 HWIC and 1 NME you can install 1-port ADSL WAN Interface Cardon the HWIC slots.
Also just enable 3 default (equal cost) routes towards the interfaces which will take care of the load balancing.
if you need more info and inputs do post out with ur requirements along with network topology in place at present..
regds

Similar Messages

I have a Cisco 2811 router with a NM-2FE2W module installed, it shows up in Sh diag but it says it is disabled?

I installed NM-2fE2W module on the 2811 router on the bottom which I guess is slot 1.
It shows up in Sh diag as disabled how can I correct this? I have the same IOS as on packet tracer 6.1 ver 12.4 (15)T. I have tried upgrading the IOS and downgrading IOS.
Slot 1:
Unknown (type 919) Port adapter
Port adapter is disabled
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-21601-02
Board Revision : B0
Deviation Number : 0-0
Fab Version : 01
PCB Serial Number : JAE0831RLPQ
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : NM-2FE2W-V2=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 97 41 01 00 C0 46 03 20 00 54 61 02
0x10: 42 42 30 80 00 00 00 00 02 01 C1 8B 4A 41 45 30
0x20: 38 33 31 52 4C 50 51 03 00 81 00 00 00 00 04 00
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Don't know for sure what's the cause of your issue, but some hardware requires a minimum IOS version and/or feature set to utilize. Also, some hardware requires additional configuration commands to enable the hardware.

Forms/Reports with Reverse Proxy and Load Balance

Hello Guys,
I want to setup an environment with apache as reverse proxy for uses with Forms and Reports.
Is there any special configuration? Or just config rewrite rules?
Something like this:
Users -----> NLB Device -----> Reverse Proxy (Apache - 2 machines) -----> Oracle Application Server (Forms/Reports - N machines)
Best Regards

I haven't made one, but I think it should work, just dont forget to use proxypass and prosypassreverse.
Regards

Cisco 3925 router with an ATM E3 card that never goes down!

Hi all,
We a Cisco 3925 router with an ATM E3 card (NM-1A-T3/E3) configured as below with 1 PVC. we see that the ATM subinterface we created for the PVC never goes down! not even when the WAN link is down! The problem with this is we are tracking the line protocol of the ATM sub interface to have VRRP failover to standby router. But because of this issue only BGP goes down whenever the WAN is down & line-protocol of the Subinterface remains up, the failover never happens & site is down. We can configure VRRP to track reachability of a BGP route as workaround but I would like an explanation or troubleshooting steps to check whats the trouble with current setup?
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(2)T4.1, MAINTENANCE INTERIM SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 30-Aug-11 08:44 by prod_rel_team
card type e3 1
interface ATM1/0
description Link to PE
mtu 1500
bandwidth 34010
no ip address
no ip proxy-arp
logging event subif-link-status
no atm ilmi-keepalive
no atm enable-ilmi-trap
end
interface ATM1/0.101 point-to-point
description PVC to MPLS PE
mtu 1500
bandwidth 2500
ip address a.b.c.d 255.255.255.252
no ip proxy-arp
ip flow monitor FMforIP4in sampler ata1to100 input
ip flow monitor FMforIP4out sampler ata1to100 output
ip nat outside
ip virtual-reassembly in
no atm enable-ilmi-trap
snmp trap link-status
pvc 1/101
vbr-nrt 8192 8192 1
vc-hold-queue 2048
oam-pvc manage
oam retry 3 5 1
oam ais-rdi 15 3
encapsulation aal5snap
protocol ip inarp
queue-depth 5 3
service-policy out Edge_Queueing
end
Thanks a lot in advance!

Your router has some configuration on it already and it would help us give you better advice if we knew what is already in the configuration. So would you post the output of show running-config (if there is sensitive information like addresses and passwords you can mask them out.
Changing the configuration register was a good start. I have a couple questions/observations that may help you get started. I notice what appears to be the same public IP address on Gig0/0 and on multilink. Did you get that address from your ISP? If so what kind of connection do you have to the ISP?
In your description you tell us that Gig0/0 is connected to a small switch, which I assume is for the LAN of your network. But that also is the interface where the public address is configured. So I am confused whether this interface is for LAN or for connecting to the ISP. Can you clarify this?
HTH
Rick

Need driver or app for ms life cam 3.0 tried to get one off the internet. cisco wireless router software said malware and virus threat. Is it safe for mac?

need driver or app for ms life cam 3.0 tried to get one off the internet. cisco wireless router software said malware and virus threat. Is it safe for mac? is this software try to protect my pc or is it A threat to macs to.

There are a number of extremly dubious sites which claim to offer Drivers for common Hardware, but actually are phishing for identies and credit card numbers and candidates to join a bot-net.
Make absolutely certain you load drivers ONLY from the manufacturer's web site.

Cisco 2600 router with 4A/S module can be terminal server

I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports? Thanks a lot

The commands mean that R1's console is connected using the first RJ-45 cable and is available on port 2001, R2's console is connected using the second RJ-45 cable and is available on port 2002 and so on. Remember that the ports are numbered as 2000 plus the line number. Hence, the first port is 2001. If you have more than eight devices and have connected a second CAB-OCTAL-ASYNC cable then you need to add a similar configuration line with the port numbers starting from 2009 till 2016.
In your configuration u configured 9 ports. So please add second cable for another 8 ports.
To connect to the console of a device, telnet to the terminal server router's loopback address and specify the port number associated to the device. For example, to connect to console of router R1 (from our example) type telnet 192.168.12.1 2001 in the Run dialog box from your PC.
For further information click the below url
http://www.cisco.com/public/technotes/smbsa/en/us/internet/config_cisco_router_term_server.html#trouble

HT4199 I have a new iPhone 4s. I have a home wi-fi network using Cisco Linksys2000 router with all settings per this article - phone will not see network if set to 5 GHz channel width - solution?? 2.4 works but is not optimal with other devices in home

I have a new iPhone 4s. I have a home wi-fi network using Cisco Linksys2000 router with all settings per this article - phone will not see network if set to 5 GHz channel width - solution?? 2.4 works but is not optimal with other devices in home (computers; tivo). Have others seen this? Any advice is much appreciated.

Stephen Spark is right - your best alternative is to use a simultaneous dual band wireless router like the AirPort Extreme. Your Cisco Linksys2000 is not a dual band router, meaning that it will be constrained to operate at the slowest speed of all the devices on your network.
The AirPort Extreme's dual networks will support all your 802.11n devices as well as all your 802.11b/g devices on both the 2.4 and 5 GHz frequencies simultaneously.

My Imac is locked with apple symbol and loading sign, how i do fix this?

my iMac is locked with apple symbol and loading sing since last night, how i do fix this?

Zap the PRAM and Reset the SMC, then try again.

My iphone 4 after update ios wont turn on and stuck in restore with apple logo and loading bar not move

When I update the ios on my Iphone 4 it wont turn on and I tried to restore it, but it stuck in restore with apple logo and loading bar not move at all, I contact apple support and they tried to help me but nothing work, then they told me to send it to replace it and I need to pay $149, that's mean if anybody has any problem with his iphone even the problem from apple software you need to pay, that's not fair at all.... I will try to sale all our apple device and by Samsung device to resolve this problems.

I believe this means that it is bricked, just sell it for parts, to someone like me

Cache and Load Balancing with Oracle APEX Listener

Hi,
I intend to use only HTTP access.
How to implement a Cache and Load Balancing with the Oracle APEX Listener?
Is it possible to do with the the standalone running APEX Listener?
Thanks by advance for any tips/documentation/references.
Kind Regards.

Hi,
I think this question is best asked in the APEX Listener forum:
ORDS, SODA & JSON in the Database
Kind regards
Sandro

VPN device with dual ISP, fail-over, and load balancing

We currently service a client that has a PIX firewall that connects to multiple, separate outside vendors via IPSEC VPN. The VPN connections are mission critical and if for any reason the VPN device or the internet connection (currently only a T1) goes down, the business goes down too. We're looking for a solution that allows dual-ISP, failover, and load balancing. I see that there are several ASA models as well as the IOS that support this but what I'm confused about is what are the requirements for the other end of the VPN, keeping in mind that the other end will always be an outside vendor and out of our control. Current VPN endpoints for outside vendors are to devices like VPN 3000 Concentrator, Sonicwall, etc. that likely do not support any type of fail-over, trunking, load-balancing. Is this just not possible?

Unless I am mistaken the ASA doesn't do VPN Load Balancing for point-to-point IPSec connections either. What you're really after is opportunistic connection failover, and/or something like DMVPN. Coordinating opportunistic failover shouldn't be too much of an issue with the partners, but be prepared for lot of questions.

Apple iPhone 5 Flashing with apple logo and load bar and apps working

flickering, with apple logo and load bar and apps in that background that all work while screen flickering, had to restore my phone to get to stop flashing and eliminate the load bar.

Hello missyfromsouthport,
After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning restoration issues:
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
You might need to use recovery mode if:
You can't update or restore because iTunes doesn't recognize your device or says it's "in recovery mode".
The Apple logo remains onscreen for several minutes with no progress bar.
The Connect to iTunes screen appears.
See what to do if the progress bar remains onscreen for several minutes
Use recovery mode
Recovery mode erases your device and restores it, which should resolve the issue. If you previously synced with iTunes or iCloud, you may be able to restore from your backup after recovery.
Turn off your device. If you can't turn it off, press and hold the Sleep/Wake and Home buttons at the same time and wait a few seconds for it to turn off.
Plug the device's USB cable into your computer only.
Hold down the device's Home button as you connect the USB cable to it.
When you see the Connect to iTunes screen, release the Home button. If you don't see this screen, try steps 1 through 3 one more time.
iTunes should open and display a message such as: "iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes."
Use iTunes to restore your device.
If you don't see your device in iTunes, follow these steps for Mac or these for Windows.
Additional Information
If you started your device in recovery mode by mistake, restart it to exit recovery mode. Or you can just wait—after 15 minutes the device will exit recovery mode by itself.
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support

I cannot import my AVCHD files by using log and transfer. I can see all the files, but when I add the file to import que it doesnt work, the status is a red (!) and says that its no data. I have tried with different cards and different cardreaders, but it

I cannot import my AVCHD files by using log and transfer. I can see all the files, but when I add the file to import que it doesnt work, the status is a red and says that its no data. I have tried with different cards and different cardreaders, but it is still the same. Why?!

Please give us more specific information -
What make/model camcorder are you using?
Are you absolutely certain this is AVCHD video? Tell us more about the video settings you used in the camcorder (eg, frame size, frame rate, quality level)
Why are you attempting Log & Transfer from a card reader instead of from your camcorder? Have you tried doing Log & Transfer from your camcorder?
Are the SD cards straight from the camcorder, unaltered, or are you just using the cards as storage?
Are you using FCE 4.0 or FCE 4.0.1?

Order Miix 2 10 With sim card and 3G support

Hi,
I want order and buy Miix 2 10 With sim card and 3G support, please help me how i can order this tablet with these features?
i'm not in us/canada.
thanks in advance.
Moderator comment: Please refrain from bumping your thread(s) / post(s) more frequently than 3 days. Doing so, unfairly, pushes other members' threads downwards. Bumping post(s) removed.

As long as it's not a Verizon iPad, sure.

Cisco 2811 Router with 3 ADSL card and load balancing

Similar Messages

Maybe you are looking for