Cisco 2811 with NM-16A as Terminal server.
Hello,
I am currently looking for a Cisco terminal server solution to remotely access through console my private Cisco home lab. I am thinking of buying Cisco 2811 but I struggle to figure out the difference which ASYNC/SYNC MODULE to use. So, my question, is it possible to use NM-16A module with Cisco 2811 or HWIC-16A module must be used? And what is the difference between them?
I found on Cisco website that NM-16A is not supported on Cisco 2811, however some forums stated that it is possible.
http://www.cisco.com/en/US/docs/ios/interface/configuration/guide/ir_nm16as.html#wp1027188
Your help is deeply appreciated.
Thank you,
Arik
Async is what you need.
I run this senario several places;
NAME: "chassis", DESCR: "2801 chassis"
PID: CISCO2801 ,
NAME: "WIC/VIC/HWIC 1", DESCR: "High Speed Wan Interface card with 16 RS232 async ports(HWIC-16A)"
PID: ,
NAME: "WIC/VIC/HWIC 3", DESCR: "9 Port FE Switch"
The HWIC is called HWIC-16A, but there is also a HWIC-8A
plus one or two CAB-HD8-ASYNC combo-squid-cables (green 1-to-8 with RJ45 plugs)
http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps6182/product_data_sheet0900aecd80274416.html
then you run rotary groups on the async SLIP's, via the cfg.
HTH
Martin
Similar Messages
-
Does Cisco 3845 with NM-16A/S support OIR feature or Hot swap for this NM.
Dear Sir
My customer would like to implement Cisco 3845 with NM-16A/S x 4. I found that Cisco 3845 support OIR function but I am not sure OIR function that Cisco 3845 support, it support with which NM models. Can anyone tell me that NM-16A/S on Cisco 3845 support OIR function on this NM or not.
Thank you very much
WisitHi,
From what I have read from the following document.
http://www.cisco.com/en/US/products/ps5855/products_installation_guide_chapter09186a00802ccf1d.html
Network Modules
Network modules install directly into slots in the rear of the router. The Cisco 3845 router supports online insertion and removal (OIR, or hot swap) of network modules. The Cisco 3825 router does not support OIR.
Caution The Cisco 3845 router supports OIR with similar modules only. If you remove a network module, along with any installed WAN or voice interface cards, install another module and card combination exactly like it.
Interface Cards
Cisco 3800 series routers do not support OIR (hot swap) of interface cards inserted directly into router slots. You must turn off the router before installing or removing an interface card.
The Cisco 3825 router and the Cisco 3845 router each provide four interface card slots, labeled on the rear panel by HWIC and a number. Each slot can be occupied by one single-wide WIC, VIC, VWIC, or HWIC.
Hope this helps
Sarb -
Error registering a Cisco 2811 with a clustered CallManager 4.3
Hello, i'm having problems registering a Cisco 2811 Gateway with a VWIC2-1MFT-E1 interface card with Cisco CallManager 4.3.
The error displayed when debugging mgcp is the following:
//-1/xxxxxxxxxxxx/MGCP/mgcp_mp_get_not_entity(828):[lvl=2]
Invalid parameter (pkt 0x4708C5E8 pkt->mgcp_parm_lines 0x00000000)
I configured mgcp by the following:
mgcp
mgcp call-agent VOIPSVR1 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp restart-delay 300
mgcp package-capability rtp-package
no mgcp package-capability res-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp validate call-agent source-ipaddr
mgcp rtp payload-type g726r16 static
mgcp profile default
dial-peer voice 100 pots
service mgcpapp
direct-inward-dial
port 0/0/0:15
Previously, the gateway downloaded xml config files from the Cisco CallManager without problems and, in addition, when trying to add a Route Group (in the CallManager) this Gateway does not appear
in the list of Available Devices although
I have added it through the Device->Gateway Menu.
Need some advice and help. Thank you in advance.Hi Jose,
The Domain name issue is outlined nicely in this doc;
MGCP Gateway Registration Failure with Cisco CallManager
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00805a316c.shtml#prob
If the IP domain name is configured in Cisco IOS on the MGCP gateway, enter the Fully Qualified Domain Name (FQDN) in the Domain Name field.
In the example: test and cisco.com represent the hostname and domain name respectively. If the IP domain name is not configured in Cisco IOS on the MGCP gateway, enter only the hostname of the MGCP gateway in the Domain Name field.
You would enter test.cisco.com (in CCM)
Hope this helps!
Rob -
Preoblem with Browse facility in Terminal Server with Normal User Login!!!
Hii All,
I am facing a problem with my addon in which I am using browsing facility.
But the Browse facility is working properly in Terminal Server with Administrator Login, but not working in Terminal Server with Normal User Login.
So how it can be solved?
Thanks & Regards,
Nabanita
Edited by: ghosh.nabanita on Aug 9, 2011 12:47 PM
Edited by: ghosh.nabanita on Aug 9, 2011 1:46 PMHi,
You have to check group polices if browsing is enabled.
Check this thread:
http://social.technet.microsoft.com/Forums/en-US/winserverGP/thread/336377db-e0cb-4c8e-b7c7-01b7c11c0e27/ -
Problem with starting devices at terminal server
Hi all,
I got a problem I can't solve at my terminal server.
In order to provide the Java ME SDK for home office use i installed it at our terminal server (Win2003Server Standard 32Bit) as administrator.
Our developers access it via RDP.
Now I got a strange effect: when I open an application in a device I get this error message:
SCHWERWIEGEND [org.openide.util.RequestProcessor]
java.lang.NullPointerException
at org.netbeans.modules.javame.platform.jme_sdk.autoinstaller.AutoInstaller$4.run(AutoInstaller.java:242)
at org.openide.util.RequestProcessor$Task.run(RequestProcessor.java:573)
[catch] at org.openide.util.RequestProcessor$Processor.run(RequestProcessor.java:1005)
No device window appears. At least not at my remote desktop. The window opened at another active remote desktop. It seems, this is the reason of the broken communication.
Now we are wondering how to install the SDK to prevent us from that effect.
Did anybody face a behavior like that and give me advice?
Thanks
Stephan Koch
Edited by: stkoch on Nov 20, 2009 6:59 AMplease post this DS forum which is at
http://forum.java.sun.com/forum.jspa?forumID=761 -
How to enable IPS IPS/IDS in cisco 2811
Hi all,
I have a Cisco 2811 with IOS Version 12.4(20)T and I need to enable IPS or IDS in this. What is the config for this?
First of all, I need to know whether I can do IPS/IDS in my router as well..
- RibinHi,
I did enabled IPS in the router and configured to notify to our log server. Below is the log I received in my log server.
What does IPS does now and what kind of logs I can expect?
Thanks,
Ribin
Apr 19 14:53:38 192.168.11.10 4546: *Apr 19 09:27:41.254: %SYS-5-CONFIG_I: Configured from console by ribin on vty0 (192.168.11.35)
Apr 19 18:04:29 192.168.11.10 4548: *Apr 19 12:38:32.601: %CRYPTO-6-IPSEC_USING_DEFAULT: IPSec is using default transforms
Apr 19 18:12:10 192.168.11.10 4549: *Apr 19 12:46:14.541: %IPS-6-ENGINE_BUILDS_STARTED: 12:46:14 UTC Apr 19 2009
Apr 19 18:12:10 192.168.11.10 4550: *Apr 19 12:46:14.541: %IPS-6-ENGINE_BUILDING: atomic-ip - 3 signatures - 1 of 13 engines
Apr 19 18:12:10 192.168.11.10 4551: *Apr 19 12:46:14.557: %IPS-6-ENGINE_READY: atomic-ip - build time 16 ms - packets for this engine will be scanned
Apr 19 18:12:10 192.168.11.10 4552: *Apr 19 12:46:14.557: %IPS-6-ALL_ENGINE_BUILDS_COMPLETE: elapsed time 16 ms -
Firefox lockdown for Terminal Server ?
I search a lockdown (GPO or mozilla.cfg) for Firefox 8 to install on Terminal Server?
Hi,
I have similar problems with AddOns on Windows Terminal Server 2008.
In the first place I installed für Each Termnial User separatley as suggested above. This must be wrong because the AddOns only worked for the user for wich the AddOns where installed latest and didn't work for all other users.
So the next time I uninstalled the AddOns for all Terminal Users and Installed again with local administrator account in install mode and started SBO in Admin Mode for that procedere. Now all users get the error message "A new version of xxx was installed. Please upgrade the AddOn in the common DB" and the AddOn Manager showing a different Version Number than the AddOn Administrator.
I didn't found anything in Documentation Ressource Center nor in the SBO Notes.
Has somebody a definite Installation procedure for Client with AddOns on Windows Terminal Server 2008?
Thanks
Christian Birkholtz -
Use of CCP on a terminal server
I would like to use Cisco Configuration Professional CCP on Windows Terminal Server, which is accessed via RDP. This server is shared by several network administrators and is used to administer our network devices.
How do I configure CCP, so that
a) more than one user can start it at the same time
b) username and password in a community are not the same for every user (you don't want a colleague of yours to make use of this software using your account)Ah,
Most excellent, I will have ZFS in July when I upgrade my ZFD to full
Zenworks suite.
Thanks!!!
Merrell
"Marcus Breiden" <[email protected]> wrote in message
news:[email protected]..
> On Wed, 04 May 2005 04:49:20 GMT, Matt Merrell wrote:
>
>> I have a Windows 2003 server, and I am probably correct in assuming that
>> you
>> can't use Zenworks to remote control it? It seems the bulk of the
>> ZfdAgent.msi install options are not available when installing it on a
>> Win2k3 box.
>
> yes.. you need ZSM for that...
> --
>
> Marcus Breiden
>
> Please change -- to - to mail me.
> The content of this mail is my private and personal opinion.
> http://www.edu-magic.net -
Hello to everyone,
I write because I have decided to pass from a cisco 2811 with ios 12.4/k9 to a cisco 1941 ios 15/k9, migrating configuration I have a problem with the ZBF.
I do not know if it's a problem of policy or differences between ios.
Could someone help me please?
Thank you all in advance
Regards,
Salvatore
Update: Configuration modified and IOS upgrade.Salvatore,
I don't know what problem exactly you face with your ZBF, but this may help you trbouleshooting your ZBF.
http://www.cisco.com/en/US/products/sw/secursw/ps1018/products_tech_note09186a0080a63b94.shtml
Thanks! -
Cisco 2600 router with 4A/S module can be terminal server
I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports? Thanks a lot
The commands mean that R1's console is connected using the first RJ-45 cable and is available on port 2001, R2's console is connected using the second RJ-45 cable and is available on port 2002 and so on. Remember that the ports are numbered as 2000 plus the line number. Hence, the first port is 2001. If you have more than eight devices and have connected a second CAB-OCTAL-ASYNC cable then you need to add a similar configuration line with the port numbers starting from 2009 till 2016.
In your configuration u configured 9 ports. So please add second cable for another 8 ports.
To connect to the console of a device, telnet to the terminal server router's loopback address and specify the port number associated to the device. For example, to connect to console of router R1 (from our example) type telnet 192.168.12.1 2001 in the Run dialog box from your PC.
For further information click the below url
http://www.cisco.com/public/technotes/smbsa/en/us/internet/config_cisco_router_term_server.html#trouble -
ASA 5510 with Cisco 2811 Router Behind it - Not forwarding traffic
Hi all,
Some might know that I have been dealing with an issue where I cannot seem to get forwarded packets to reach their destinations behind an ASA 5510 that has a Cisco 2811 connected directly behind it.
Some examples that work.
I can SSH into the ASA.
I can SSH to the Cisco Routers behind the ASA.
I cannot reach items beind the Cisco Routers.
My Configuration is this (I am sure I included a bunch of info I didn't need to, but I am hoping it'll help!):
I have a static Ip assigned to my Ouside Interface Ethernet 0/1
It has an IP address of 199.195.xxx.xxx
I am trying to learn how to shape network traffic (this is all new to me) via the ASA and the Routers to specific devices.
The Inside Interface on the ASA is 10.10.1.1 255.255.255.252
The Outside Interface on the 2811 is 10.10.1.2 255.255.255.252
I can ping the router from the ASA. I can SSH through the ASA to the router.
BUT I CANNOT ACCESS DEVICES BEHIND THE ROUTER.
So, I wanted to BAM that statement above because I just don't kjnow where the issue is. Is the issue on the router or the ASA, my guess is, the router, but I just don't know.
Here are my configs, helpfully someone can help.
ASA errors on the ASDM when I try and hit resources; specifically a web device behind the ASA and the 2811. It's Ip address 192.168.1.5 it's listening on port 80.Static IP, not assigned via DHCP.
6
Feb 14 2014
19:38:56
98.22.121.x
41164
192.168.1.5
80
Built inbound TCP connection 1922859 for Outside:98.22.121.x/41164 (98.22.121.x/41164) to Inside:192.168.1.5/80 (199.195.168.x/8080)
6
Feb 14 2014
19:38:56
10.10.1.2
80
98.22.121.x
41164
Deny TCP (no connection) from 10.10.1.2/80 to 98.22.121.x/41164 flags SYN ACK on interface Inside
ASA5510# sh nat
Auto NAT Policies (Section 2)
1 (DMZ) to (Outside) source static ROUTER-2821 interface service tcp ssh 2222
translate_hits = 1, untranslate_hits = 18
2 (Inside) to (Outside) source static ROUTER-2811 interface service tcp ssh 222
translate_hits = 0, untranslate_hits = 13
3 (VOIP) to (Outside) source static ROUTER-3745 interface service tcp ssh 2223
translate_hits = 0, untranslate_hits = 3
4 (Inside) to (Outside) source static RDP-DC1 interface service tcp 3389 3389
translate_hits = 0, untranslate_hits = 236
5 (Inside) to (Outside) source static WEBCAM-01 interface service tcp www 8080
translate_hits = 0, untranslate_hits = 162
Manual NAT Policies (Section 3)
1 (any) to (Outside) source dynamic PAT-SOURCE interface
translate_hits = 1056862, untranslate_hits = 83506
ASA5510# show access-list
access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 4096)
alert-interval 300
access-list USERS; 1 elements; name hash: 0x50681c1e
access-list USERS line 1 standard permit 10.10.1.0 255.255.255.0 (hitcnt=0) 0xdd6ba495
access-list Outside_access_in; 5 elements; name hash: 0xe796c137
access-list Outside_access_in line 1 extended permit tcp host 98.22.121.x object ROUTER-2811 eq ssh (hitcnt=37) 0x5a53778d
access-list Outside_access_in line 1 extended permit tcp host 98.22.121.x host 10.10.1.2 eq ssh (hitcnt=37) 0x5a53778d
access-list Outside_access_in line 2 extended permit tcp host 98.22.121.x object ROUTER-2821 eq ssh (hitcnt=8) 0x9f32bc21
access-list Outside_access_in line 2 extended permit tcp host 98.22.121.x host 10.10.0.2 eq ssh (hitcnt=8) 0x9f32bc21
access-list Outside_access_in line 3 extended permit tcp host 98.22.121.x interface Outside eq https (hitcnt=0) 0x385488b2
access-list Outside_access_in line 4 extended permit tcp host 98.22.121.x object WEBCAM-01 eq www (hitcnt=60) 0xe66674ec
access-list Outside_access_in line 4 extended permit tcp host 98.22.121.x host 192.168.1.5 eq www (hitcnt=60) 0xe66674ec
access-list Outside_access_in line 5 extended permit tcp host 98.22.121.x object RDP-DC1 eq 3389 (hitcnt=3) 0x02f13f4e
access-list Outside_access_in line 5 extended permit tcp host 98.22.121.x host 192.168.1.2 eq 3389 (hitcnt=3) 0x02f13f4e
access-list dmz-access-vlan1; 1 elements; name hash: 0xc3450860
access-list dmz-access-vlan1 line 1 extended permit ip 128.162.1.0 255.255.255.0 any (hitcnt=0) 0x429fedf1
access-list dmz-access; 3 elements; name hash: 0xf53f5801
access-list dmz-access line 1 remark Permit all traffic to DC1
access-list dmz-access line 2 extended permit ip 128.162.1.0 255.255.255.0 host 192.168.1.2 (hitcnt=0) 0xd2dced0a
access-list dmz-access line 3 remark Permit only DNS traffic to DNS server
access-list dmz-access line 4 extended permit udp 128.162.1.0 255.255.255.0 host 192.168.1.2 eq domain (hitcnt=0) 0xbb21093e
access-list dmz-access line 5 remark Permit ICMP to all devices in DC
access-list dmz-access line 6 extended permit icmp 128.162.1.0 255.255.255.0 192.168.1.0 255.255.255.0 (hitcnt=0) 0x71269ef7
CISCO-2811#show access-lists
Standard IP access list 1
10 permit any (1581021 matches)
CISCO-2811#show translate
CISCO-2811#show route
CISCO-2811#show route-map
CISCO-2811#show host
CISCO-2811#show hosts
Default domain is maladomini.int
Name/address lookup uses domain service
Name servers are 192.168.1.2, 199.195.168.4, 205.171.2.65, 205.171.3.65, 8.8.8.8
Codes: UN - unknown, EX - expired, OK - OK, ?? - revalidate
temp - temporary, perm - permanent
NA - Not Applicable None - Not defined
Host Port Flags Age Type Address(es)
api.mixpanel.com None (temp, OK) 2 IP 198.23.64.21
198.23.64.22
198.23.64.18
198.23.64.19
198.23.64.20
ASA5510:
ASA5510# sh run all
: Saved
ASA Version 9.1(4)
command-alias exec h help
command-alias exec lo logout
command-alias exec p ping
command-alias exec s show
terminal width 80
hostname ASA5510
domain-name maladomini.int
enable password x encrypted
no fips enable
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session permit tcp any4 any4
xlate per-session permit tcp any4 any6
xlate per-session permit tcp any6 any4
xlate per-session permit tcp any6 any6
xlate per-session permit udp any4 any4 eq domain
xlate per-session permit udp any4 any6 eq domain
xlate per-session permit udp any6 any4 eq domain
xlate per-session permit udp any6 any6 eq domain
passwd x encrypted
names
dns-guard
lacp system-priority 32768
interface Ethernet0/0
description LAN Interface
speed auto
duplex auto
no flowcontrol send on
nameif Inside
security-level 100
ip address 10.10.1.1 255.255.255.252
delay 10
interface Ethernet0/1
description WAN Interface
speed auto
duplex auto
no flowcontrol send on
nameif Outside
security-level 0
ip address 199.195.168.xxx 255.255.255.240
delay 10
interface Ethernet0/2
description DMZ
speed auto
duplex auto
no flowcontrol send on
nameif DMZ
security-level 100
ip address 10.10.0.1 255.255.255.252
delay 10
interface Ethernet0/3
description VOIP
speed auto
duplex auto
no flowcontrol send on
nameif VOIP
security-level 100
ip address 10.10.2.1 255.255.255.252
delay 10
interface Management0/0
speed auto
duplex auto
management-only
shutdown
nameif management
security-level 0
no ip address
delay 10
regex _default_gator "Gator"
regex _default_firethru-tunnel_2 "[/\\]cgi[-]bin[/\\]proxy"
regex _default_shoutcast-tunneling-protocol "1"
regex _default_http-tunnel "[/\\]HT_PortLog.aspx"
regex _default_x-kazaa-network "[\r\n\t ]+[xX]-[kK][aA][zZ][aA][aA]-[nN][eE][tT][wW][oO][rR][kK]"
regex _default_msn-messenger "[Aa][Pp][Pp][Ll][Ii][Cc][Aa][Tt][Ii][Oo][Nn][/\\][Xx][-][Mm][Ss][Nn][-][Mm][Ee][Ss][Ss][Ee][Nn][Gg][Ee][Rr]"
regex _default_GoToMyPC-tunnel_2 "[/\\]erc[/\\]Poll"
regex _default_gnu-http-tunnel_uri "[/\\]index[.]html"
regex _default_aim-messenger "[Hh][Tt][Tt][Pp][.][Pp][Rr][Oo][Xx][Yy][.][Ii][Cc][Qq][.][Cc][Oo][Mm]"
regex _default_gnu-http-tunnel_arg "crap"
regex _default_icy-metadata "[\r\n\t ]+[iI][cC][yY]-[mM][eE][tT][aA][dD][aA][tT][aA]"
regex _default_GoToMyPC-tunnel "machinekey"
regex _default_windows-media-player-tunnel "NSPlayer"
regex _default_yahoo-messenger "YMSG"
regex _default_httport-tunnel "photo[.]exectech[-]va[.]com"
regex _default_firethru-tunnel_1 "firethru[.]com"
checkheaps check-interval 60
checkheaps validate-checksum 60
boot system disk0:/asa914-k8.bin
ftp mode passive
clock timezone UTC 0
dns domain-lookup Outside
dns server-group DefaultDNS
name-server 199.195.168.4
name-server 205.171.2.65
name-server 205.171.3.65
domain-name maladomini.int
same-security-traffic permit inter-interface
object service ah pre-defined
service ah
description This is a pre-defined object
object service eigrp pre-defined
service eigrp
description This is a pre-defined object
object service esp pre-defined
service esp
description This is a pre-defined object
object service gre pre-defined
service gre
description This is a pre-defined object
object service icmp pre-defined
service icmp
description This is a pre-defined object
object service icmp6 pre-defined
service icmp6
description This is a pre-defined object
object service igmp pre-defined
service igmp
description This is a pre-defined object
object service igrp pre-defined
service igrp
description This is a pre-defined object
object service ip pre-defined
service ip
description This is a pre-defined object
object service ipinip pre-defined
service ipinip
description This is a pre-defined object
object service ipsec pre-defined
service esp
description This is a pre-defined object
object service nos pre-defined
service nos
description This is a pre-defined object
object service ospf pre-defined
service ospf
description This is a pre-defined object
object service pcp pre-defined
service pcp
description This is a pre-defined object
object service pim pre-defined
service pim
description This is a pre-defined object
object service pptp pre-defined
service gre
description This is a pre-defined object
object service snp pre-defined
service snp
description This is a pre-defined object
object service tcp pre-defined
service tcp
description This is a pre-defined object
object service udp pre-defined
service udp
description This is a pre-defined object
object service tcp-aol pre-defined
service tcp destination eq aol
description This is a pre-defined object
object service tcp-bgp pre-defined
service tcp destination eq bgp
description This is a pre-defined object
object service tcp-chargen pre-defined
service tcp destination eq chargen
description This is a pre-defined object
object service tcp-cifs pre-defined
service tcp destination eq cifs
description This is a pre-defined object
object service tcp-citrix-ica pre-defined
service tcp destination eq citrix-ica
description This is a pre-defined object
object service tcp-ctiqbe pre-defined
service tcp destination eq ctiqbe
description This is a pre-defined object
object service tcp-daytime pre-defined
service tcp destination eq daytime
description This is a pre-defined object
object service tcp-discard pre-defined
service tcp destination eq discard
description This is a pre-defined object
object service tcp-domain pre-defined
service tcp destination eq domain
description This is a pre-defined object
object service tcp-echo pre-defined
service tcp destination eq echo
description This is a pre-defined object
object service tcp-exec pre-defined
service tcp destination eq exec
description This is a pre-defined object
object service tcp-finger pre-defined
service tcp destination eq finger
description This is a pre-defined object
object service tcp-ftp pre-defined
service tcp destination eq ftp
description This is a pre-defined object
object service tcp-ftp-data pre-defined
service tcp destination eq ftp-data
description This is a pre-defined object
object service tcp-gopher pre-defined
service tcp destination eq gopher
description This is a pre-defined object
object service tcp-ident pre-defined
service tcp destination eq ident
description This is a pre-defined object
object service tcp-imap4 pre-defined
service tcp destination eq imap4
description This is a pre-defined object
object service tcp-irc pre-defined
service tcp destination eq irc
description This is a pre-defined object
object service tcp-hostname pre-defined
service tcp destination eq hostname
description This is a pre-defined object
object service tcp-kerberos pre-defined
service tcp destination eq kerberos
description This is a pre-defined object
object service tcp-klogin pre-defined
service tcp destination eq klogin
description This is a pre-defined object
object service tcp-kshell pre-defined
service tcp destination eq kshell
description This is a pre-defined object
object service tcp-ldap pre-defined
service tcp destination eq ldap
description This is a pre-defined object
object service tcp-ldaps pre-defined
service tcp destination eq ldaps
description This is a pre-defined object
object service tcp-login pre-defined
service tcp destination eq login
description This is a pre-defined object
object service tcp-lotusnotes pre-defined
service tcp destination eq lotusnotes
description This is a pre-defined object
object service tcp-nfs pre-defined
service tcp destination eq nfs
description This is a pre-defined object
object service tcp-netbios-ssn pre-defined
service tcp destination eq netbios-ssn
description This is a pre-defined object
object service tcp-whois pre-defined
service tcp destination eq whois
description This is a pre-defined object
object service tcp-nntp pre-defined
service tcp destination eq nntp
description This is a pre-defined object
object service tcp-pcanywhere-data pre-defined
service tcp destination eq pcanywhere-data
description This is a pre-defined object
object service tcp-pim-auto-rp pre-defined
service tcp destination eq pim-auto-rp
description This is a pre-defined object
object service tcp-pop2 pre-defined
service tcp destination eq pop2
description This is a pre-defined object
object service tcp-pop3 pre-defined
service tcp destination eq pop3
description This is a pre-defined object
object service tcp-pptp pre-defined
service tcp destination eq pptp
description This is a pre-defined object
object service tcp-lpd pre-defined
service tcp destination eq lpd
description This is a pre-defined object
object service tcp-rsh pre-defined
service tcp destination eq rsh
description This is a pre-defined object
object service tcp-rtsp pre-defined
service tcp destination eq rtsp
description This is a pre-defined object
object service tcp-sip pre-defined
service tcp destination eq sip
description This is a pre-defined object
object service tcp-smtp pre-defined
service tcp destination eq smtp
description This is a pre-defined object
object service tcp-ssh pre-defined
service tcp destination eq ssh
description This is a pre-defined object
object service tcp-sunrpc pre-defined
service tcp destination eq sunrpc
description This is a pre-defined object
object service tcp-tacacs pre-defined
service tcp destination eq tacacs
description This is a pre-defined object
object service tcp-talk pre-defined
service tcp destination eq talk
description This is a pre-defined object
object service tcp-telnet pre-defined
service tcp destination eq telnet
description This is a pre-defined object
object service tcp-uucp pre-defined
service tcp destination eq uucp
description This is a pre-defined object
object service tcp-www pre-defined
service tcp destination eq www
description This is a pre-defined object
object service tcp-http pre-defined
service tcp destination eq www
description This is a pre-defined object
object service tcp-https pre-defined
service tcp destination eq https
description This is a pre-defined object
object service tcp-cmd pre-defined
service tcp destination eq rsh
description This is a pre-defined object
object service tcp-sqlnet pre-defined
service tcp destination eq sqlnet
description This is a pre-defined object
object service tcp-h323 pre-defined
service tcp destination eq h323
description This is a pre-defined object
object service tcp-udp-cifs pre-defined
service tcp-udp destination eq cifs
description This is a pre-defined object
object service tcp-udp-discard pre-defined
service tcp-udp destination eq discard
description This is a pre-defined object
object service tcp-udp-domain pre-defined
service tcp-udp destination eq domain
description This is a pre-defined object
object service tcp-udp-echo pre-defined
service tcp-udp destination eq echo
description This is a pre-defined object
object service tcp-udp-kerberos pre-defined
service tcp-udp destination eq kerberos
description This is a pre-defined object
object service tcp-udp-nfs pre-defined
service tcp-udp destination eq nfs
description This is a pre-defined object
object service tcp-udp-pim-auto-rp pre-defined
service tcp-udp destination eq pim-auto-rp
description This is a pre-defined object
object service tcp-udp-sip pre-defined
service tcp-udp destination eq sip
description This is a pre-defined object
object service tcp-udp-sunrpc pre-defined
service tcp-udp destination eq sunrpc
description This is a pre-defined object
object service tcp-udp-tacacs pre-defined
service tcp-udp destination eq tacacs
description This is a pre-defined object
object service tcp-udp-www pre-defined
service tcp-udp destination eq www
description This is a pre-defined object
object service tcp-udp-http pre-defined
service tcp-udp destination eq www
description This is a pre-defined object
object service tcp-udp-talk pre-defined
service tcp-udp destination eq talk
description This is a pre-defined object
object service udp-biff pre-defined
service udp destination eq biff
description This is a pre-defined object
object service udp-bootpc pre-defined
service udp destination eq bootpc
description This is a pre-defined object
object service udp-bootps pre-defined
service udp destination eq bootps
description This is a pre-defined object
object service udp-cifs pre-defined
service udp destination eq cifs
description This is a pre-defined object
object service udp-discard pre-defined
service udp destination eq discard
description This is a pre-defined object
object service udp-domain pre-defined
service udp destination eq domain
description This is a pre-defined object
object service udp-dnsix pre-defined
service udp destination eq dnsix
description This is a pre-defined object
object service udp-echo pre-defined
service udp destination eq echo
description This is a pre-defined object
object service udp-www pre-defined
service udp destination eq www
description This is a pre-defined object
object service udp-http pre-defined
service udp destination eq www
description This is a pre-defined object
object service udp-nameserver pre-defined
service udp destination eq nameserver
description This is a pre-defined object
object service udp-kerberos pre-defined
service udp destination eq kerberos
description This is a pre-defined object
object service udp-mobile-ip pre-defined
service udp destination eq mobile-ip
description This is a pre-defined object
object service udp-nfs pre-defined
service udp destination eq nfs
description This is a pre-defined object
object service udp-netbios-ns pre-defined
service udp destination eq netbios-ns
description This is a pre-defined object
object service udp-netbios-dgm pre-defined
service udp destination eq netbios-dgm
description This is a pre-defined object
object service udp-ntp pre-defined
service udp destination eq ntp
description This is a pre-defined object
object service udp-pcanywhere-status pre-defined
service udp destination eq pcanywhere-status
description This is a pre-defined object
object service udp-pim-auto-rp pre-defined
service udp destination eq pim-auto-rp
description This is a pre-defined object
object service udp-radius pre-defined
service udp destination eq radius
description This is a pre-defined object
object service udp-radius-acct pre-defined
service udp destination eq radius-acct
description This is a pre-defined object
object service udp-rip pre-defined
service udp destination eq rip
description This is a pre-defined object
object service udp-secureid-udp pre-defined
service udp destination eq secureid-udp
description This is a pre-defined object
object service udp-sip pre-defined
service udp destination eq sip
description This is a pre-defined object
object service udp-snmp pre-defined
service udp destination eq snmp
description This is a pre-defined object
object service udp-snmptrap pre-defined
service udp destination eq snmptrap
description This is a pre-defined object
object service udp-sunrpc pre-defined
service udp destination eq sunrpc
description This is a pre-defined object
object service udp-syslog pre-defined
service udp destination eq syslog
description This is a pre-defined object
object service udp-tacacs pre-defined
service udp destination eq tacacs
description This is a pre-defined object
object service udp-talk pre-defined
service udp destination eq talk
description This is a pre-defined object
object service udp-tftp pre-defined
service udp destination eq tftp
description This is a pre-defined object
object service udp-time pre-defined
service udp destination eq time
description This is a pre-defined object
object service udp-who pre-defined
service udp destination eq who
description This is a pre-defined object
object service udp-xdmcp pre-defined
service udp destination eq xdmcp
description This is a pre-defined object
object service udp-isakmp pre-defined
service udp destination eq isakmp
description This is a pre-defined object
object service icmp6-unreachable pre-defined
service icmp6 unreachable
description This is a pre-defined object
object service icmp6-packet-too-big pre-defined
service icmp6 packet-too-big
description This is a pre-defined object
object service icmp6-time-exceeded pre-defined
service icmp6 time-exceeded
description This is a pre-defined object
object service icmp6-parameter-problem pre-defined
service icmp6 parameter-problem
description This is a pre-defined object
object service icmp6-echo pre-defined
service icmp6 echo
description This is a pre-defined object
object service icmp6-echo-reply pre-defined
service icmp6 echo-reply
description This is a pre-defined object
object service icmp6-membership-query pre-defined
service icmp6 membership-query
description This is a pre-defined object
object service icmp6-membership-report pre-defined
service icmp6 membership-report
description This is a pre-defined object
object service icmp6-membership-reduction pre-defined
service icmp6 membership-reduction
description This is a pre-defined object
object service icmp6-router-renumbering pre-defined
service icmp6 router-renumbering
description This is a pre-defined object
object service icmp6-router-solicitation pre-defined
service icmp6 router-solicitation
description This is a pre-defined object
object service icmp6-router-advertisement pre-defined
service icmp6 router-advertisement
description This is a pre-defined object
object service icmp6-neighbor-solicitation pre-defined
service icmp6 neighbor-solicitation
description This is a pre-defined object
object service icmp6-neighbor-advertisement pre-defined
service icmp6 neighbor-advertisement
description This is a pre-defined object
object service icmp6-neighbor-redirect pre-defined
service icmp6 neighbor-redirect
description This is a pre-defined object
object service icmp-echo pre-defined
service icmp echo
description This is a pre-defined object
object service icmp-echo-reply pre-defined
service icmp echo-reply
description This is a pre-defined object
object service icmp-unreachable pre-defined
service icmp unreachable
description This is a pre-defined object
object service icmp-source-quench pre-defined
service icmp source-quench
description This is a pre-defined object
object service icmp-redirect pre-defined
service icmp redirect
description This is a pre-defined object
object service icmp-alternate-address pre-defined
service icmp alternate-address
description This is a pre-defined object
object service icmp-router-advertisement pre-defined
service icmp router-advertisement
description This is a pre-defined object
object service icmp-router-solicitation pre-defined
service icmp router-solicitation
description This is a pre-defined object
object service icmp-time-exceeded pre-defined
service icmp time-exceeded
description This is a pre-defined object
object service icmp-parameter-problem pre-defined
service icmp parameter-problem
description This is a pre-defined object
object service icmp-timestamp-request pre-defined
service icmp timestamp-request
description This is a pre-defined object
object service icmp-timestamp-reply pre-defined
service icmp timestamp-reply
description This is a pre-defined object
object service icmp-information-request pre-defined
service icmp information-request
description This is a pre-defined object
object service icmp-information-reply pre-defined
service icmp information-reply
description This is a pre-defined object
object service icmp-mask-request pre-defined
service icmp mask-request
description This is a pre-defined object
object service icmp-mask-reply pre-defined
service icmp mask-reply
description This is a pre-defined object
object service icmp-traceroute pre-defined
service icmp traceroute
description This is a pre-defined object
object service icmp-conversion-error pre-defined
service icmp conversion-error
description This is a pre-defined object
object service icmp-mobile-redirect pre-defined
service icmp mobile-redirect
description This is a pre-defined object
object network ROUTER-2811
host 10.10.1.2
object network ROUTER-2821
host 10.10.0.2
object network WEBCAM-01
host 192.168.1.5
object network DNS-SERVER
host 192.168.1.2
object network ROUTER-3745
host 10.10.2.2
object network RDP-DC1
host 192.168.1.2
object-group network PAT-SOURCE
network-object 10.10.1.0 255.255.255.252
network-object 10.10.0.0 255.255.255.252
network-object 10.10.2.0 255.255.255.252
network-object 192.168.0.0 255.255.255.0
network-object 172.16.10.0 255.255.255.0
network-object 172.16.20.0 255.255.255.0
network-object 128.162.1.0 255.255.255.0
network-object 128.162.10.0 255.255.255.0
network-object 128.162.20.0 255.255.255.0
object-group network DM_INLINE_NETWORK_2
network-object host 98.22.121.x
object-group network Outside_access_in
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object gre
access-list USERS standard permit 10.10.1.0 255.255.255.0
access-list Outside_access_in extended permit tcp host 98.22.121.x object ROUTER-2811 eq ssh
access-list Outside_access_in extended permit tcp host 98.22.121.x object ROUTER-2821 eq ssh
access-list Outside_access_in extended permit tcp host 98.22.121.x interface Outside eq https
access-list Outside_access_in extended permit tcp host 98.22.121.x object WEBCAM-01 eq www
access-list Outside_access_in extended permit tcp host 98.22.121.x object RDP-DC1 eq 3389
access-list dmz-access-vlan1 extended permit ip 128.162.1.0 255.255.255.0 any
access-list dmz-access remark Permit all traffic to DC1
access-list dmz-access extended permit ip 128.162.1.0 255.255.255.0 host 192.168.1.2
access-list dmz-access remark Permit only DNS traffic to DNS server
access-list dmz-access extended permit udp 128.162.1.0 255.255.255.0 host 192.168.1.2 eq domain
access-list dmz-access remark Permit ICMP to all devices in DC
access-list dmz-access extended permit icmp 128.162.1.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging buffer-size 4096
logging asdm-buffer-size 100
logging asdm informational
logging flash-minimum-free 3076
logging flash-maximum-allocation 1024
logging rate-limit 1 10 message 747001
logging rate-limit 1 1 message 402116
logging rate-limit 1 10 message 620002
logging rate-limit 1 10 message 717015
logging rate-limit 1 10 message 717018
logging rate-limit 1 10 message 201013
logging rate-limit 1 10 message 201012
logging rate-limit 1 1 message 313009
logging rate-limit 100 1 message 750003
logging rate-limit 100 1 message 750002
logging rate-limit 100 1 message 750004
logging rate-limit 1 10 message 419003
logging rate-limit 1 10 message 405002
logging rate-limit 1 10 message 405003
logging rate-limit 1 10 message 421007
logging rate-limit 1 10 message 405001
logging rate-limit 1 10 message 421001
logging rate-limit 1 10 message 421002
logging rate-limit 1 10 message 337004
logging rate-limit 1 10 message 337005
logging rate-limit 1 10 message 337001
logging rate-limit 1 10 message 337002
logging rate-limit 1 60 message 199020
logging rate-limit 1 10 message 337003
logging rate-limit 2 5 message 199011
logging rate-limit 1 10 message 199010
logging rate-limit 1 10 message 337009
logging rate-limit 2 5 message 199012
logging rate-limit 1 10 message 710002
logging rate-limit 1 10 message 209003
logging rate-limit 1 10 message 209004
logging rate-limit 1 10 message 209005
logging rate-limit 1 10 message 431002
logging rate-limit 1 10 message 431001
logging rate-limit 1 1 message 447001
logging rate-limit 1 10 message 110003
logging rate-limit 1 10 message 110002
logging rate-limit 1 10 message 429007
logging rate-limit 1 10 message 216004
logging rate-limit 1 10 message 450001
flow-export template timeout-rate 30
flow-export active refresh-interval 1
mtu Inside 1500
mtu Outside 1500
mtu management 1500
mtu DMZ 1500
mtu VOIP 1500
icmp unreachable rate-limit 1 burst-size 1
icmp deny any Outside
asdm image disk0:/asdm-715.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network ROUTER-2811
nat (Inside,Outside) static interface service tcp ssh 222
object network ROUTER-2821
nat (DMZ,Outside) static interface service tcp ssh 2222
object network WEBCAM-01
nat (Inside,Outside) static interface service tcp www 8080
object network ROUTER-3745
nat (VOIP,Outside) static interface service tcp ssh 2223
object network RDP-DC1
nat (Inside,Outside) static interface service tcp 3389 3389
nat (any,Outside) after-auto source dynamic PAT-SOURCE interface
access-group Outside_access_in in interface Outside
ipv6 dhcprelay timeout 60
router rip
network 10.0.0.0
version 2
no auto-summary
route Outside 0.0.0.0 0.0.0.0 199.195.168.113 1
route Inside 128.162.1.0 255.255.255.0 10.10.0.2 1
route Inside 128.162.10.0 255.255.255.0 10.10.0.2 1
route Inside 128.162.20.0 255.255.255.0 10.10.0.2 1
route Inside 172.16.10.0 255.255.255.0 10.10.1.2 1
route Inside 172.16.20.0 255.255.255.0 10.10.1.2 1
route Inside 192.168.1.0 255.255.255.0 10.10.1.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
action continue
no cts server-group
no cts sxp enable
no cts sxp default
no cts sxp default source-ip
cts sxp reconciliation period 120
cts sxp retry period 120
user-identity enable
user-identity domain LOCAL
user-identity default-domain LOCAL
user-identity action mac-address-mismatch remove-user-ip
user-identity inactive-user-timer minutes 60
user-identity poll-import-user-group-timer hours 8
user-identity ad-agent active-user-database full-download
user-identity ad-agent hello-timer seconds 30 retry-times 5
no user-identity user-not-found enable
aaa authentication ssh console LOCAL
http server enable 443
http 0.0.0.0 0.0.0.0 Inside
http 98.22.121.x 255.255.255.255 Outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
no snmp-server enable traps syslog
no snmp-server enable traps ipsec start stop
no snmp-server enable traps entity config-change fru-insert fru-remove fan-failure power-supply power-supply-presence cpu-temperature chassis-temperature power-supply-temperature chassis-fan-failure
no snmp-server enable traps memory-threshold
no snmp-server enable traps interface-threshold
no snmp-server enable traps remote-access session-threshold-exceeded
no snmp-server enable traps connection-limit-reached
no snmp-server enable traps cpu threshold rising
no snmp-server enable traps ikev2 start stop
no snmp-server enable traps nat packet-discard
snmp-server enable
snmp-server listen-port 161
fragment size 200 Inside
fragment chain 24 Inside
fragment timeout 5 Inside
no fragment reassembly full Inside
fragment size 200 Outside
fragment chain 24 Outside
fragment timeout 5 Outside
no fragment reassembly full Outside
fragment size 200 management
fragment chain 24 management
fragment timeout 5 management
no fragment reassembly full management
fragment size 200 DMZ
fragment chain 24 DMZ
fragment timeout 5 DMZ
no fragment reassembly full DMZ
fragment size 200 VOIP
fragment chain 24 VOIP
fragment timeout 5 VOIP
no fragment reassembly full VOIP
no sysopt connection timewait
sysopt connection tcpmss 1380
sysopt connection tcpmss minimum 0
sysopt connection permit-vpn
sysopt connection reclassify-vpn
no sysopt connection preserve-vpn-flows
no sysopt radius ignore-secret
no sysopt noproxyarp Inside
no sysopt noproxyarp Outside
no sysopt noproxyarp management
no sysopt noproxyarp DMZ
no sysopt noproxyarp VOIP
service password-recovery
no crypto ipsec ikev2 sa-strength-enforcement
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto ipsec security-association replay window-size 64
crypto ipsec security-association pmtu-aging infinite
crypto ipsec fragmentation before-encryption Inside
crypto ipsec fragmentation before-encryption Outside
crypto ipsec fragmentation before-encryption management
crypto ipsec fragmentation before-encryption DMZ
crypto ipsec fragmentation before-encryption VOIP
crypto ipsec df-bit copy-df Inside
crypto ipsec df-bit copy-df Outside
crypto ipsec df-bit copy-df management
crypto ipsec df-bit copy-df DMZ
crypto ipsec df-bit copy-df VOIP
crypto ca trustpool policy
revocation-check none
crl cache-time 60
crl enforcenextupdate
crypto isakmp identity auto
crypto isakmp nat-traversal 20
crypto ikev2 cookie-challenge 50
crypto ikev2 limit max-in-negotiation-sa 100
no crypto ikev2 limit max-sa
crypto ikev2 redirect during-auth
crypto ikev1 limit max-in-negotiation-sa 20
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Inside
ssh 98.22.121.x 255.255.255.255 Outside
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
console timeout 0
vpn-addr-assign aaa
vpn-addr-assign dhcp
vpn-addr-assign local reuse-delay 0
ipv6-vpn-addr-assign aaa
ipv6-vpn-addr-assign local reuse-delay 0
no vpn-sessiondb max-other-vpn-limit
no vpn-sessiondb max-anyconnect-premium-or-essentials-limit
no remote-access threshold
l2tp tunnel hello 60
tls-proxy maximum-session 100
threat-detection rate dos-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate dos-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate bad-packet-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate bad-packet-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate acl-drop rate-interval 600 average-rate 400 burst-rate 800
threat-detection rate acl-drop rate-interval 3600 average-rate 320 burst-rate 640
threat-detection rate conn-limit-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate conn-limit-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate icmp-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate icmp-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate scanning-threat rate-interval 600 average-rate 5 burst-rate 10
threat-detection rate scanning-threat rate-interval 3600 average-rate 4 burst-rate 8
threat-detection rate syn-attack rate-interval 600 average-rate 100 burst-rate 200
threat-detection rate syn-attack rate-interval 3600 average-rate 80 burst-rate 160
threat-detection rate fw-drop rate-interval 600 average-rate 400 burst-rate 1600
threat-detection rate fw-drop rate-interval 3600 average-rate 320 burst-rate 1280
threat-detection rate inspect-drop rate-interval 600 average-rate 400 burst-rate 1600
threat-detection rate inspect-drop rate-interval 3600 average-rate 320 burst-rate 1280
threat-detection rate interface-drop rate-interval 600 average-rate 2000 burst-rate 8000
threat-detection rate interface-drop rate-interval 3600 average-rate 1600 burst-rate 6400
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 24.56.178.140 source Outside prefer
ssl server-version any
ssl client-version any
ssl encryption rc4-sha1 dhe-aes128-sha1 dhe-aes256-sha1 aes128-sha1 aes256-sha1 3des-sha1
ssl certificate-authentication fca-timeout 2
webvpn
memory-size percent 50
port 443
dtls port 443
character-encoding none
no http-proxy
no https-proxy
default-idle-timeout 1800
portal-access-rule none
no csd enable
no anyconnect enable
no tunnel-group-list enable
no tunnel-group-preference group-url
rewrite order 65535 enable resource-mask *
no internal-password
no onscreen-keyboard
no default-language
no smart-tunnel notification-icon
no keepout
cache
no disable
max-object-size 1000
min-object-size 0
no cache-static-content enable
lmfactor 20
expiry-time 1
no auto-signon
no error-recovery disable
no ssl-server-check
no mus password
mus host mus.cisco.com
no hostscan data-limit
: # show import webvpn customization
: Template
: DfltCustomization
: # show import webvpn url-list
: Template
: # show import webvpn translation-table
: Translation Tables' Templates:
: PortForwarder
: banners
: customization
: url-list
: webvpn
: Translation Tables:
: fr PortForwarder
: fr customization
: fr webvpn
: ja PortForwarder
: ja customization
: ja webvpn
: ru PortForwarder
: ru customization
: ru webvpn
: # show import webvpn mst-translation
: No MS translation tables defined
: # show import webvpn webcontent
: No custom webcontent is loaded
: # show import webvpn AnyConnect-customization
: No OEM resources defined
: # show import webvpn plug-in
group-policy DfltGrpPolicy internal
group-policy DfltGrpPolicy attributes
banner none
wins-server none
dns-server none
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout 30
vpn-idle-timeout alert-interval 1
vpn-session-timeout none
vpn-session-timeout alert-interval 1
vpn-filter none
ipv6-vpn-filter none
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec ssl-clientless
password-storage disable
ip-comp disable
re-xauth disable
group-lock none
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelall
ipv6-split-tunnel-policy tunnelall
split-tunnel-network-list none
default-domain none
split-dns none
split-tunnel-all-dns disable
intercept-dhcp 255.255.255.255 disable
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout 30
ip-phone-bypass disable
client-bypass-protocol disable
gateway-fqdn none
leap-bypass disable
nem disable
backup-servers keep-client-config
msie-proxy server none
msie-proxy method no-modify
msie-proxy except-list none
msie-proxy local-bypass disable
msie-proxy pac-url none
msie-proxy lockdown enable
vlan none
nac-settings none
address-pools none
ipv6-address-pools none
smartcard-removal-disconnect enable
scep-forwarding-url none
client-firewall none
client-access-rule none
webvpn
url-list none
filter none
homepage none
html-content-filter none
port-forward name Application Access
port-forward disable
http-proxy disable
sso-server none
anyconnect ssl dtls enable
anyconnect mtu 1406
anyconnect firewall-rule client-interface private none
anyconnect firewall-rule client-interface public none
anyconnect keep-installer installed
anyconnect ssl keepalive 20
anyconnect ssl rekey time none
anyconnect ssl rekey method none
anyconnect dpd-interval client 30
anyconnect dpd-interval gateway 30
anyconnect ssl compression none
anyconnect dtls compression none
anyconnect modules none
anyconnect profiles none
anyconnect ask none
customization none
keep-alive-ignore 4
http-comp gzip
download-max-size 2147483647
upload-max-size 2147483647
post-max-size 2147483647
user-storage none
storage-objects value cookies,credentials
storage-key none
hidden-shares none
smart-tunnel disable
activex-relay enable
unix-auth-uid 65534
unix-auth-gid 65534
file-entry enable
file-browsing enable
url-entry enable
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information
smart-tunnel auto-signon disable
anyconnect ssl df-bit-ignore disable
anyconnect routing-filtering-ignore disable
smart-tunnel tunnel-policy tunnelall
always-on-vpn profile-setting
password-policy minimum-length 3
password-policy minimum-changes 0
password-policy minimum-lowercase 0
password-policy minimum-uppercase 0
password-policy minimum-numeric 0
password-policy minimum-special 0
password-policy lifetime 0
no password-policy authenticate-enable
quota management-session 0
tunnel-group DefaultL2LGroup type ipsec-l2l
tunnel-group DefaultL2LGroup general-attributes
no accounting-server-group
default-group-policy DfltGrpPolicy
tunnel-group DefaultL2LGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
isakmp keepalive threshold 10 retry 2
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultRAGroup type remote-access
tunnel-group DefaultRAGroup general-attributes
no address-pool
no ipv6-address-pool
authentication-server-group LOCAL
secondary-authentication-server-group none
no accounting-server-group
default-group-policy DfltGrpPolicy
no dhcp-server
no strip-realm
no nat-assigned-to-public-ip
no scep-enrollment enable
no password-management
no override-account-disable
no strip-group
no authorization-required
username-from-certificate CN OU
secondary-username-from-certificate CN OU
authentication-attr-from-server primary
authenticated-session-username primary
tunnel-group DefaultRAGroup webvpn-attributes
customization DfltCustomization
authentication aaa
no override-svc-download
no radius-reject-message
no proxy-auth sdi
no pre-fill-username ssl-client
no pre-fill-username clientless
no secondary-pre-fill-username ssl-client
no secondary-pre-fill-username clientless
dns-group DefaultDNS
no without-csd
tunnel-group DefaultRAGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
no ikev1 radius-sdi-xauth
isakmp keepalive threshold 300 retry 2
ikev1 user-authentication xauth
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultRAGroup ppp-attributes
no authentication pap
authentication chap
authentication ms-chap-v1
no authentication ms-chap-v2
no authentication eap-proxy
tunnel-group DefaultWEBVPNGroup type remote-access
tunnel-group DefaultWEBVPNGroup general-attributes
no address-pool
no ipv6-address-pool
authentication-server-group LOCAL
secondary-authentication-server-group none
no accounting-server-group
default-group-policy DfltGrpPolicy
no dhcp-server
no strip-realm
no nat-assigned-to-public-ip
no scep-enrollment enable
no password-management
no override-account-disable
no strip-group
no authorization-required
username-from-certificate CN OU
secondary-username-from-certificate CN OU
authentication-attr-from-server primary
authenticated-session-username primary
tunnel-group DefaultWEBVPNGroup webvpn-attributes
customization DfltCustomization
authentication aaa
no override-svc-download
no radius-reject-message
no proxy-auth sdi
no pre-fill-username ssl-client
no pre-fill-username clientless
no secondary-pre-fill-username ssl-client
no secondary-pre-fill-username clientless
dns-group DefaultDNS
no without-csd
tunnel-group DefaultWEBVPNGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
no ikev1 radius-sdi-xauth
isakmp keepalive threshold 300 retry 2
ikev1 user-authentication xauth
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
no authentication pap
authentication chap
authentication ms-chap-v1
no authentication ms-chap-v2
no authentication eap-proxy
class-map type inspect http match-all _default_gator
match request header user-agent regex _default_gator
class-map type inspect http match-all _default_msn-messenger
match response header content-type regex _default_msn-messenger
class-map type inspect http match-all _default_yahoo-messenger
match request body regex _default_yahoo-messenger
class-map type inspect http match-all _default_windows-media-player-tunnel
match request header user-agent regex _default_windows-media-player-tunnel
class-map type inspect http match-all _default_gnu-http-tunnel
match request args regex _default_gnu-http-tunnel_arg
match request uri regex _default_gnu-http-tunnel_uri
class-map type inspect http match-all _default_firethru-tunnel
match request header host regex _default_firethru-tunnel_1
match request uri regex _default_firethru-tunnel_2
class-map type inspect http match-all _default_aim-messenger
match request header host regex _default_aim-messenger
class-map type inspect http match-all _default_http-tunnel
match request uri regex _default_http-tunnel
class-map type inspect http match-all _default_kazaa
match response header regex _default_x-kazaa-network count gt 0
class-map type inspect http match-all _default_shoutcast-tunneling-protocol
match request header regex _default_icy-metadata regex _default_shoutcast-tunneling-protocol
class-map class-default
match any
class-map inspection_default
match default-inspection-traffic
class-map type inspect http match-all _default_GoToMyPC-tunnel
match request args regex _default_GoToMyPC-tunnel
match request uri regex _default_GoToMyPC-tunnel_2
class-map type inspect http match-all _default_httport-tunnel
match request header host regex _default_httport-tunnel
policy-map type inspect rtsp _default_rtsp_map
description Default RTSP policymap
parameters
policy-map type inspect ipv6 _default_ipv6_map
description Default IPV6 policy-map
parameters
verify-header type
verify-header order
match header routing-type range 0 255
drop log
policy-map type inspect h323 _default_h323_map
description Default H.323 policymap
parameters
no rtp-conformance
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum client auto
message-length maximum 512
no message-length maximum server
dns-guard
protocol-enforcement
nat-rewrite
no id-randomization
no id-mismatch
no tsig enforced
policy-map type inspect esmtp _default_esmtp_map
description Default ESMTP policy-map
parameters
mask-banner
no mail-relay
no special-character
no allow-tls
match cmd line length gt 512
drop-connection log
match cmd RCPT count gt 100
drop-connection log
match body line length gt 998
log
match header line length gt 998
drop-connection log
match sender-address length gt 320
drop-connection log
match MIME filename length gt 255
drop-connection log
match ehlo-reply-parameter others
mask
policy-map type inspect ip-options _default_ip_options_map
description Default IP-OPTIONS policy-map
parameters
router-alert action allow
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225 _default_h323_map
inspect h323 ras _default_h323_map
inspect rsh
inspect rtsp
inspect esmtp _default_esmtp_map
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options _default_ip_options_map
inspect icmp
inspect icmp error
inspect pptp
class class-default
policy-map type inspect sip _default_sip_map
description Default SIP policymap
parameters
im
no ip-address-privacy
traffic-non-sip
no rtp-conformance
policy-map type inspect dns _default_dns_map
description Default DNS policy-map
parameters
no message-length maximum client
no message-leI ran those commands while I had the nat off on the router and here are the results. note, i didn't make any changes to the ASA as you only said to remove the router RIP which I did and reloaded and no change.
As long as the statements ip nat outside on the Fastethernet 0/0 is off and the ip nat inside is off on the vlan and the overload statement is taken out, I cannot hit the internet.
CISCO-2811#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CISCO-2811(config)#int
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/1.3
CISCO-2811(config-subif)#no ip nat inside
CISCO-2811(config-subif)#exit
CISCO-2811(config)#inter
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/0
CISCO-2811(config-if)#no ip nat outside
CISCO-2811(config-if)#exit
CISCO-2811(config)#$nside source list 1 interface FastEthernet0/0 overload
Dynamic mapping in use, do you want to delete all entries? [no]: y
CISCO-2811(config)#exit
CISCO-2811#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.10.1.1 202 c47d.4f3b.8ea6 ARPA FastEthernet0/0
Internet 10.10.1.2 - 0019.55a7.2ae8 ARPA FastEthernet0/0
Internet 172.16.10.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.1
Internet 172.16.10.3 238 0011.5c73.28c1 ARPA FastEthernet0/1.1
Internet 172.16.10.50 72 cc2d.8c78.065a ARPA FastEthernet0/1.1
Internet 172.16.20.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.2
Internet 172.16.20.3 196 0011.5c73.28c2 ARPA FastEthernet0/1.2
Internet 192.168.1.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.3
Internet 192.168.1.2 0 0024.e864.01a8 ARPA FastEthernet0/1.3
Internet 192.168.1.3 155 0011.5c73.28c0 ARPA FastEthernet0/1.3
Internet 192.168.1.5 61 4802.2a4c.1c74 ARPA FastEthernet0/1.3
Internet 192.168.1.20 0 5cf9.dd52.5fa9 ARPA FastEthernet0/1.3
Internet 192.168.1.50 0 308c.fb47.f2d9 ARPA FastEthernet0/1.3
Internet 192.168.1.51 1 ec35.8677.4057 ARPA FastEthernet0/1.3
Internet 192.168.1.52 1 b418.d136.ef72 ARPA FastEthernet0/1.3
Internet 192.168.1.53 1 8853.9572.e113 ARPA FastEthernet0/1.3
Internet 192.168.1.54 12 0009.b044.9f23 ARPA FastEthernet0/1.3
Internet 192.168.1.55 0 f47b.5e9a.7ae5 ARPA FastEthernet0/1.3
Internet 192.168.1.149 0 001e.4fc5.a199 ARPA FastEthernet0/1.3
Internet 192.168.1.174 0 b8ac.6fff.af83 ARPA FastEthernet0/1.3
CISCO-2811#sh ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
+ - replicated route, % - next hop override
Gateway of last resort is 10.10.1.1 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 10.10.1.1
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.10.1.0/30 is directly connected, FastEthernet0/0
L 10.10.1.2/32 is directly connected, FastEthernet0/0
172.16.0.0/16 is variably subnetted, 4 subnets, 2 masks
C 172.16.10.0/24 is directly connected, FastEthernet0/1.1
L 172.16.10.1/32 is directly connected, FastEthernet0/1.1
C 172.16.20.0/24 is directly connected, FastEthernet0/1.2
L 172.16.20.1/32 is directly connected, FastEthernet0/1.2
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, FastEthernet0/1.3
L 192.168.1.1/32 is directly connected, FastEthernet0/1.3
ASA
ASA5510# sh arp
Inside 10.10.1.2 0019.55a7.2ae8 12342
Outside 199.195.168.113 000c.4243.581a 2
Outside 199.195.168.116 e05f.b947.116b 2436
Outside 199.195.168.120 0017.c58a.1123 9192
DMZ 10.10.0.2 0025.849f.63e0 3192
VOIP 10.10.2.2 000d.bcdc.fc40 7754
ASA5510# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 199.195.168.113 to network 0.0.0.0
S 172.16.20.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S 172.16.10.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S 128.162.1.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
S 128.162.10.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
S 128.162.20.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
C 199.195.168.112 255.255.255.240 is directly connected, Outside
C 10.10.0.0 255.255.255.252 is directly connected, DMZ
C 10.10.1.0 255.255.255.252 is directly connected, Inside
S 192.168.1.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S* 0.0.0.0 0.0.0.0 [1/0] via 199.195.168.113, Outside
ASA5510# show xlate
35 in use, 784 most used
Flags: D - DNS, e - extended, I - identity, i - dynamic, r - portmap,
s - static, T - twice, N - net-to-net
TCP PAT from DMZ:10.10.0.2 22-22 to Outside:199.195.168.x 2222-2222
flags sr idle 481:54:14 timeout 0:00:00
TCP PAT from Inside:10.10.1.2 22-22 to Outside:199.195.168.x 222-222
flags sr idle 51:06:46 timeout 0:00:00
TCP PAT from VOIP:10.10.2.2 22-22 to Outside:199.195.168.x 2223-2223
flags sr idle 687:32:27 timeout 0:00:00
TCP PAT from Inside:192.168.1.2 3389-3389 to Outside:199.195.168.x 3389-3389
flags sr idle 457:17:01 timeout 0:00:00
TCP PAT from Inside:192.168.1.5 80-80 to Outside:199.195.168.x 8080-8080
flags sr idle 52:18:58 timeout 0:00:00
NAT from Outside:0.0.0.0/0 to any:0.0.0.0/0
flags sIT idle 353:10:21 timeout 0:00:00
UDP PAT from any:10.10.1.2/52581 to Outside:199.195.168.x/52581 flags ri idle 0:00:00 timeout 0:00:30
UDP PAT from any:10.10.1.2/55389 to Outside:199.195.168.x/55389 flags ri idle 0:00:03 timeout 0:00:30
UDP PAT from any:10.10.1.2/51936 to Outside:199.195.168.x/51936 flags ri idle 0:00:04 timeout 0:00:30
UDP PAT from any:10.10.1.2/51345 to Outside:199.195.168.x/51345 flags ri idle 0:00:09 timeout 0:00:30
UDP PAT from any:10.10.1.2/55985 to Outside:199.195.168.x/55985 flags ri idle 0:00:18 timeout 0:00:30
UDP PAT from any:10.10.1.2/49368 to Outside:199.195.168.x/49368 flags ri idle 0:00:22 timeout 0:00:30
UDP PAT from any:10.10.1.2/52441 to Outside:199.195.168.x/52441 flags ri idle 0:00:23 timeout 0:00:30
TCP PAT from any:10.10.1.2/57908 to Outside:199.195.168.x/57908 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57907 to Outside:199.195.168.x/57907 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57906 to Outside:199.195.168.x/57906 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57896 to Outside:199.195.168.x/57896 flags ri idle 0:09:09 timeout 0:00:30
TCP PAT from any:10.10.1.2/57879 to Outside:199.195.168.x/57879 flags ri idle 0:10:23 timeout 0:00:30
TCP PAT from any:10.10.1.2/49441 to Outside:199.195.168.x/49441 flags ri idle 0:20:52 timeout 0:00:30
TCP PAT from any:10.10.1.2/57868 to Outside:199.195.168.x/57868 flags ri idle 0:25:28 timeout 0:00:30
TCP PAT from any:10.10.1.2/60519 to Outside:199.195.168.x/60519 flags ri idle 0:44:11 timeout 0:00:30
TCP PAT from any:10.10.1.2/60491 to Outside:199.195.168.x/60491 flags ri idle 0:44:20 timeout 0:00:30
TCP PAT from any:10.10.1.2/60484 to Outside:199.195.168.x/60484 flags ri idle 0:44:35 timeout 0:00:30
TCP PAT from any:10.10.1.2/60480 to Outside:199.195.168.x/60480 flags ri idle 0:44:51 timeout 0:00:30
TCP PAT from any:10.10.1.2/53851 to Outside:199.195.168.x/53851 flags ri idle 0:54:14 timeout 0:00:30
TCP PAT from any:10.10.1.2/57812 to Outside:199.195.168.x/57812 flags ri idle 0:58:30 timeout 0:00:30
TCP PAT from any:10.10.1.2/57810 to Outside:199.195.168.x/57810 flags ri idle 0:58:32 timeout 0:00:30
TCP PAT from any:10.10.1.2/53847 to Outside:199.195.168.x/53847 flags ri idle 1:00:18 timeout 0:00:30
TCP PAT from any:10.10.1.2/57808 to Outside:199.195.168.x/57808 flags ri idle 1:07:58 timeout 0:00:30
TCP PAT from any:10.10.1.2/60406 to Outside:199.195.168.x/60406 flags ri idle 1:42:13 timeout 0:00:30
TCP PAT from any:10.10.1.2/49259 to Outside:199.195.168.x/49259 flags ri idle 7:39:44 timeout 0:00:30
TCP PAT from any:10.10.1.2/49191 to Outside:199.195.168.x/49191 flags ri idle 7:42:39 timeout 0:00:30
TCP PAT from any:10.10.1.2/55951 to Outside:199.195.168.x/55951 flags ri idle 23:11:40 timeout 0:00:30
TCP PAT from any:10.10.1.2/55944 to Outside:199.195.168.x/55944 flags ri idle 23:15:19 timeout 0:00:30
TCP PAT from any:10.10.1.2/55942 to Outside:199.195.168.x/55942 flags ri idle 23:15:24 timeout 0:00:30
ASA5510# sh conn all
149 in use, 815 most used
TCP Outside 74.125.193.108:993 Inside 10.10.1.2:57879, idle 0:12:37, bytes 6398, flags UIO
TCP Outside 174.35.24.74:80 Inside 192.168.1.20:53879, idle 0:00:01, bytes 0, flags saA
TCP Outside 174.35.24.74:80 Inside 192.168.1.20:53878, idle 0:00:01, bytes 0, flags saA
TCP Outside 17.149.36.177:5223 Inside 10.10.1.2:60480, idle 0:16:53, bytes 4539, flags UIO
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53877, idle 0:00:02, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53876, idle 0:00:02, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53875, idle 0:00:05, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53874, idle 0:00:05, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53872, idle 0:00:11, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53871, idle 0:00:11, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53868, idle 0:00:08, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53867, idle 0:00:08, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53860, idle 0:00:17, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53859, idle 0:00:17, bytes 0, flags saA
TCP Outside 17.172.233.95:5223 Inside 10.10.1.2:49191, idle 0:18:48, bytes 7384, flags UIO
TCP Outside 17.178.100.43:443 Inside 10.10.1.2:57810, idle 0:56:21, bytes 5797, flags UFIO
TCP Outside 23.206.216.93:80 Inside 10.10.1.2:53847, idle 0:54:15, bytes 2683, flags UFIO
TCP Outside 143.127.93.90:80 Inside 10.10.1.2:49259, idle 0:12:20, bytes 13315, flags UIO
TCP Outside 74.125.225.53:443 Inside 192.168.1.20:53864, idle 0:00:11, bytes 0, flags saA
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49204, idle 0:00:04, bytes 67, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:50122, idle 0:00:07, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63275, idle 0:00:08, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63306, idle 0:00:18, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65059, idle 0:00:22, bytes 46, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64681, idle 0:00:30, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64661, idle 0:00:30, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.20:55618, idle 0:00:32, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65056, idle 0:00:33, bytes 48, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:59433, idle 0:00:41, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.20:52178, idle 0:00:42, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:61414, idle 0:00:43, bytes 34, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65438, idle 0:00:44, bytes 44, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63686, idle 0:00:44, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65416, idle 0:00:45, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:53047, idle 0:00:47, bytes 32, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:62213, idle 0:00:46, bytes 74, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:52347, idle 0:00:46, bytes 92, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:58069, idle 0:00:46, bytes 64, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:50753, idle 0:00:46, bytes 74, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65381, idle 0:00:50, bytes 50, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65082, idle 0:00:50, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64038, idle 0:00:50, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49309, idle 0:00:51, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64034, idle 0:00:51, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49197, idle 0:00:51, bytes 50, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64728, idle 0:00:51, bytes 49, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64309, idle 0:00:51, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63289, idle 0:00:51, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64174, idle 0:00:52, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:39286, idle 0:01:09, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63726, idle 0:01:09, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65482, idle 0:01:12, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65091, idle 0:01:13, bytes 61, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64976, idle 0:01:13, bytes 57, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63749, idle 0:00:51, bytes 103, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64043, idle 0:01:14, bytes 52, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64267, idle 0:01:24, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64467, idle 0:01:26, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65504, idle 0:01:26, bytes 46, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:38946, idle 0:01:35, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63701, idle 0:01:38, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63879, idle 0:01:46, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:58516, idle 0:01:49, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63227, idle 0:01:51, bytes 62, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:65446, idle 0:01:53, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49166, idle 0:01:55, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:56680, idle 0:02:01, bytes 33, flags -
UDP Outside 192.55.83.30:53 Inside 192.168.1.2:65073, idle 0:00:44, bytes 50, flags -
TCP Outside 74.125.193.109:993 Inside 10.10.1.2:57808, idle 0:39:33, bytes 6392, flags UFIO
TCP Outside 74.125.225.54:443 Inside 192.168.1.20:53863, idle 0:00:13, bytes 0, flags saA
TCP Outside 143.127.93.89:80 Inside 10.10.1.2:60519, idle 0:46:30, bytes 346, flags UO
TCP Outside 74.125.225.32:443 Inside 192.168.1.20:53881, idle 0:00:01, bytes 0, flags saA
TCP Outside 74.125.225.32:443 Inside 192.168.1.20:53880, idle 0:00:01, bytes 0, flags saA
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:60627, idle 0:00:39, bytes 78, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:52088, idle 0:00:39, bytes 86, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:50533, idle 0:00:39, bytes 76, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:63347, idle 0:00:39, bytes 80, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:62213, idle 0:00:40, bytes 37, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:52347, idle 0:00:40, bytes 46, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:58069, idle 0:00:40, bytes 32, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:50753, idle 0:00:40, bytes 37, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.174:52254, idle 0:01:09, bytes 43, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.174:50791, idle 0:01:25, bytes 35, flags -
TCP Outside 74.125.225.46:443 Inside 192.168.1.20:53870, idle 0:00:08, bytes 0, flags saA
TCP Outside 17.173.255.101:443 Inside 10.10.1.2:53851, idle 0:56:33, bytes 58, flags UfIO
TCP Outside 64.4.23.147:33033 Inside 10.10.1.2:55944, idle 0:44:45, bytes 558164, flags UFIO
TCP Outside 74.125.225.35:443 Inside 192.168.1.20:53869, idle 0:00:09, bytes 0, flags saA
UDP Outside 64.4.23.175:33033 Inside 192.168.1.174:26511, idle 0:01:17, bytes 28, flags -
UDP Outside 192.54.112.30:53 Inside 192.168.1.2:65380, idle 0:00:44, bytes 49, flags -
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57908, idle 0:10:47, bytes 7895, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57907, idle 0:10:49, bytes 20323, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57906, idle 0:10:47, bytes 6539, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57868, idle 0:27:44, bytes 6395, flags UIO
TCP Outside 91.190.218.59:443 Inside 10.10.1.2:55942, idle 0:41:39, bytes 2727, flags UFIO
TCP Outside 17.172.233.123:5223 Inside 10.10.1.2:49441, idle 0:23:10, bytes 4409, flags UIO
TCP Outside 74.125.225.41:443 Inside 192.168.1.20:53862, idle 0:00:16, bytes 0, flags saA
TCP Outside 74.125.225.41:443 Inside 192.168.1.20:53861, idle 0:00:16, bytes 0, flags saA
TCP Outside 143.127.93.115:80 Inside 10.10.1.2:60406, idle 0:42:59, bytes 970, flags UFIO
TCP Outside 143.127.93.118:80 Inside 10.10.1.2:60484, idle 0:46:54, bytes 328, flags UO
TCP Outside 17.172.233.98:5223 Inside 10.10.1.2:57896, idle 0:11:28, bytes 5081, flags UIO
UDP Outside 111.221.74.16:33033 Inside 192.168.1.174:26511, idle 0:01:18, bytes 31, flags -
TCP Outside 17.149.36.103:5223 Inside 192.168.1.174:60729, idle 0:00:04, bytes 0, flags saA
UDP Outside 192.5.6.30:53 Inside 192.168.1.2:65317, idle 0:00:44, bytes 51, flags -
UDP Outside 192.12.94.30:53 Inside 192.168.1.2:65356, idle 0:00:44, bytes 54, flags -
TCP Outside 17.149.36.180:5223 Inside 10.10.1.2:55951, idle 0:46:08, bytes 14059, flags UFIO
UDP Outside 111.221.74.28:33033 Inside 192.168.1.174:26511, idle 0:01:20, bytes 33, flags -
TCP Outside 63.235.20.160:80 Inside 192.168.1.20:53873, idle 0:00:08, bytes 0, flags saA
TCP Outside 50.19.127.112:443 Inside 192.168.1.50:60678, idle 0:00:00, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60728, idle 0:00:14, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60727, idle 0:00:15, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60726, idle 0:00:15, bytes 0, flags saA
TCP Outside 65.55.122.234:443 Inside 192.168.1.174:2492, idle 0:00:16, bytes 0, flags saA
TCP Outside 65.55.122.234:2492 Inside 192.168.1.174:2492, idle 0:00:16, bytes 0, flags saA
UDP Outside 157.55.56.170:33033 Inside 192.168.1.174:26511, idle 0:01:21, bytes 37, flags -
TCP Outside 74.125.230.207:443 Inside 192.168.1.20:53866, idle 0:00:11, bytes 0, flags saA
TCP Outside 74.125.230.207:443 Inside 192.168.1.20:53865, idle 0:00:11, bytes 0, flags saA
UDP Outside 111.221.74.18:33033 Inside 192.168.1.174:26511, idle 0:01:17, bytes 29, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:55546, idle 0:00:06, bytes 46, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:60277, idle 0:00:06, bytes 46, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:55618, idle 0:00:34, bytes 43, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:60627, idle 0:00:36, bytes 78, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:52088, idle 0:00:36, bytes 86, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:50533, idle 0:00:36, bytes 76, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:63347, idle 0:00:36, bytes 80, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:56958, idle 0:01:24, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:51360, idle 0:01:26, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.174:50791, idle 0:01:27, bytes 35, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:54134, idle 0:01:46, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.174:58516, idle 0:01:50, bytes 51, flags -
TCP Outside 23.207.7.46:80 Inside 192.168.1.55:59350, idle 0:00:02, bytes 0, flags saA
TCP Outside 23.207.7.46:80 Inside 192.168.1.55:59349, idle 0:00:16, bytes 0, flags saA
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:50122, idle 0:00:09, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:48088, idle 0:00:42, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:62213, idle 0:00:45, bytes 74, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:52347, idle 0:00:45, bytes 92, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:58069, idle 0:00:45, bytes 64, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:50753, idle 0:00:45, bytes 74, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:61414, idle 0:00:47, bytes 34, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:54481, idle 0:01:08, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:52254, idle 0:01:09, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:40285, idle 0:01:34, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:65446, idle 0:01:55, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:46155, idle 0:02:00, bytes 33, flags -
UDP Outside 66.104.81.70:5070 Inside 192.168.1.174:57609, idle 0:00:11, bytes 46, flags -
UDP Outside 64.4.23.156:33033 Inside 192.168.1.174:26511, idle 0:01:14, bytes 38, flags -
TCP Outside 65.54.167.15:12350 Inside 10.10.1.2:60491, idle 0:11:02, bytes 1405, flags UIO
TCP Outside 17.172.192.35:443 Inside 10.10.1.2:57812, idle 0:56:11, bytes 6116, flags UFIO
UDP Outside 157.55.56.176:33033 Inside 192.168.1.174:26511, idle 0:01:16, bytes 32, flags -
TCP Inside 192.168.1.20:53667 NP Identity Ifc 10.10.1.1:22, idle 0:00:00, bytes 37555, flags UOB
TCP Inside 10.10.1.2:53431 NP Identity Ifc 10.10.1.1:22, idle 0:09:03, bytes 20739, flags UOB
Ran on the ASA while overload statements were down on the router:
ASA5510# packet-tracer input Inside tcp 192.168.1.100 12345 8.8.8.8 80
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 Outside
Phase: 2
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Phase: 3
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 4
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 1988699, packet dispatched to next module
Result:
input-interface: Inside
input-status: up
input-line-status: up
output-interface: Outside
output-status: up
output-line-status: up
Action: allow
Had to put these back in to get to the internet:
CISCO-2811#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CISCO-2811(config)#inter
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/0
CISCO-2811(config-if)#ip nat
CISCO-2811(config-if)#ip nat Outside
CISCO-2811(config-if)#exit
CISCO-2811(config)#in
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/1.3
CISCO-2811(config-subif)#ip nat inside
CISCO-2811(config-subif)#exit
CISCO-2811(config)#$de source list 1 interface FastEthernet0/0 overload
CISCO-2811(config)#
Screenshot of ASDM: -
Hello,
I was trying to set terminal server using NM-16A module in Cisco 2651XM router but no luck. I did use 2511 in the past without any issue but i don't know if i'm not doing anything wrong with this module as i never set terminal server with this module before. Initially i thought my NM-16A is bad but when i do "sh ver" then router shows 16 Terminal Lines. All i get connection refused by remote host when i try to console other device even after clearing lines. Can anyone please help?
Thanks,You may want to take a look at this doc:
http://www.cisco.com/en/US/docs/ios/interface/configuration/guide/ir_nm16as.html
It has been a while since I have used the async interfaces on a 25xx series device. I have used the async mod on a 2600 and aside from setting baud rate, parity, etc. I don't recall any special issues. I have one in my lab now, but apparently I have misplaced my async octopus cables. Which is a bit disconcerting.
Anyway, hope that helps.
Regards,
Bill
Please remember to rate helpful posts. -
Cisco 1921/1841 as a terminal server
Hi,
we need a terminal server.
I researched a little bit on cisco.com and found out that there are several options, and because of that I am not sure what to buy.
I write down the routers, card models and cables and you guys try to explain what the differences are.
- 1921 ISR2
- HWIC-8A 8-Port Async HWIC x2
- CAB-OCTAL-ASYNC 8 Lead Octal Cable (68 pin to 8 Male RJ-45s) x2
- 1841 ISR
- HWIC-8A 8-Port Async HWIC x2
- CAB-HD8-ASYNC High Density 8-port EIA-232 Async Cable x2
I found this card too:
HWIC-8A/S-232 8-Port Async/Sync Serial HWIC, EIA-232
and this one costs double the price of the HWIC-8A 8-Port Async HWIC but I am not sure if this is for a terminal server.
Is this option enough to manage 16 devices vie the console?
- 1921 ISR2
- HWIC-8A 8-Port Async HWIC x2
- CAB-OCTAL-ASYNC 8 Lead Octal Cable (68 pin to 8 Male RJ-45s) x2Hi,
This is my first post and I just stumbled upon your question.
The CAB-OCTAL-ASYNC has a 60-pin connector that will not work with HWIC-8A or HWIC-16A.
The HWIC-8A is compatible with (amongst others) your 1841 ISR and 1921 ISR2.
The CAB-HD8-ASYNC will work with HWIC-8A (and if you have them HWIC-16A). Each CAB-HD8-ASYNC can support up to 8 serial interfaces. So to answer your questioh about the a workable hardware list, one options is as follows:
- 1921 ISR2
- HWIC-8A 8-Port Async HWIC x2
- CAB-HD8-ASYNC x2
Hope this helps. -
Hi,
I have one of the 16 spider cables from my 2611 Terminal Server plugged into a console port of a device that exists behind the firewall. But, it does not appear to be working.
Config of 2611 Terminal Server below and output of show line when an attempt is made to connect the remote cisco router. I already have this solution working for other routers and all works.
Config of line 33 48 on terminal server:-
line 33 48
session-timeout 5
timeout login response 15
no exec
transport input telnet
transport output all
BunkerA_2nd_TS#sh host
Default domain is not set
Name/address lookup uses static mappings
Codes: UN - unknown, EX - expired, OK - OK, ?? - revalidate
temp - temporary, perm - permanent
NA - Not Applicable None - Not defined
Host Port Flags Age Type Address(es)
XIT 2041 (perm, OK) 0 IP 10.64.8.40
BunkerA_2nd_TS#
BunkerA_2nd_TS#sh line 41
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 41 TTY 9600/9600 - - - - - 15 0 0/0 -
Line 41, Location: "", Type: "SUN-CMD"
Length: 34 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600, no parity, 2 stopbits, 8 databits
Status: Ready, Connected, Active
Capabilities: EXEC Suppressed
Modem state: Ready
Modem hardware state: noCTS DSR DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
00:10:00 00:05:00 none not set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:15
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: 00:01:51
Editing is enabled.
History is enabled, history size is 20.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are telnet.
Allowed output transports are pad v120 telnet rlogin udptn.
Preferred transport is telnet.
No output characters are padded
No special data dispatching charactersMary
I wonder about this line of output:
Status: Ready, Connected, Active
and wonder what happens if you issue the command clear line 41 from privilege mode of the terminal server?
The output shows that it has been used 15 times. Has it worked before or has it ALWAYS failed?
If you remove the terminal server cable and connect directly to the router console port with a PC does it work?
If you connect a different cable from the terminal server to the router and attempt access with the different reverse telnet port does it work?
If you can provide answers to these we might be closer to having answers to your issue.
HTH
Rick -
Terminal Server Farm balancing with down server
I have an 11501 that is balancing connections between my 10 terminal servers.
We are using roundrobin because we were told by TAC that leastconn and ACA do not work well with terminal server environment.
The problem is that whenever a server goes down and comes back up that server is not first inline for people reconnecting. I need help finding a way, once the down server comes back online, to make this server have a higher weight until its connections are about equal to what the other server loads are.
Any help would be greatly appreciated.Hi,
in my pinion balance leastconn should the job as it only counts the number of connections see :
http://www.cisco.com/en/US/customer/products/hw/contnetw/ps792/products_configuration_guide_chapter09186a008029c621.html#wp1038118:
balance leastconn - Least connection algorithm. This balance method chooses a running service that has the fewest number of connections.
We do not recommend that you use UDP content rules with the balance leastconn load-balancing algorithm. The service connection counters do not increment and remain at 0 because UDP is a connectionless protocol. Because the counters remain at 0, the CSS will give inconsistent results.
So if your terminal service is a running via UDP you are having a problem but in any other case it should do the job from the description given above.
The balance aca will fail due to the fact that the first and keepalive is very fast and so it can not determin the real load what you already found out.
Which method did you use balance aca or balance leastconn?
Cheers,
Joerg
Maybe you are looking for
-
I used the article "How to connect Sony Tablet with adb protocol through USB?" Article ID:474705. Everytime I restart the computer now I get a open with window. When I select Notepad and open it I get 0x54c Noswal\.android\adb_usb.****** How do i un
-
my imac screen is glowing neon colors works fine just has black backround and glowing icons so i can see anything in regular color
-
Initial Indexing Mode ( On / Off ) ?
Hello ALL We are trying to configure the queue parameters for <i>initial indexing</i> and <i>Daily update of index</i> . We are not able to see the <i>Initial Indexing Mode</i> parameter and for that we can set it up : <i> On</i> for initial index
-
Hi Experts, I have created one workflow and inside it I have created one TASK. I am using the Item BO BUS2000131 to do the processing and for sending mail. It is working properly and also I am getting Links for the Order under "Objects and attachment
-
Happy New Year Everyone!! My 8-year old got a Zen Nano for Christmas and I am having some technical difficulties. I am downloading music to the player and the player is showing the artist and title, however, the music is not playing on the player. I