Cisco 2851 with 2-SFP ??

Hi All,
First of All wishing you all Very Happy new year!!!!
I want to whether is it possible to connect 2-HWIC-SFP ( 1GB ) modules to Cisco 2851 Router ???

Only one.   See below (Table 3).
Cisco Gigabit Ethernet High-Speed WAN Interface Card

Similar Messages

  • Cisco 2851 with multiple SIP registrars

    I'm trying to setup up my 2851 to register with two registrars (sipgate.co.uk and voiptalk.org).
    Looking at "show sip-ua register status" it seems that I have successfully registered, but oddly it is trying to use the authentication of each other on both:
    router1#show sip-ua register status
    --------------------- Registrar-Index  1 ---------------------
    Line                             peer       expires(sec) registered P-Associ-URI
    ================================ ========== ============ ========== ============
    100XXXX                          -1         465          yes       
    8449XXXX                         -1         165          no        
    --------------------- Registrar-Index  2 ---------------------
    Line                             peer       expires(sec) registered P-Associ-URI
    ================================ ========== ============ ========== ============
    100XXXX                          -1         165          no        
    8449XXXX                         -1         2865         yes 
    So it looks like it's trying to register using 100XXXX and 8449XXXX with both registrars, which is wrong.
    I confirmed this using tcpdump.
    I've been using this page to help configure the sip trunks: http://www.cisco.com/c/en/us/td/docs/ios/voice/sip/configuration/guide/15_1/sip_15_1_book/sip_cg-multi-registrars.html
    I have this as my sip-ua config:
    sip-ua
    credentials number 100XXXX username 100XXXX password 7 PASSWORD1 realm sipgate.co.uk
    credentials number 8449XXXX username 8449XXXX password 7 PASSWORD2 realm voiptalk.org
    nat symmetric role active
    nat symmetric check-media-src
    no remote-party-id
    retry invite 2
    retry register 10
    timers connect 100
    registrar 1 dns:sipgate.co.uk expires 3600
    registrar 2 dns:voiptalk.org expires 3600
    connection-reuse
    host-registrar
    protocol mode dual-stack preference ipv6
    Am I missing something obvious? :/ What could I be doing wrong?

    Hope this link helps out:
    http://tekcert.com/blog/2011/02/03/cme-configuration-example-sip-trunks-viatalk-and-voipms
    rate the post accordingly.
    Regards,
    Kevin
    Sent from Cisco Technical Support Android App

  • CISCO 2851 with IPS configuration

    Hi guys,i'm planning to do an IOS IPS configuration on a newly purchased 2851 router, the spec as below:
    CISCO2851-HSEC/K9
    CISCO 2800 AdvanceIPservice :Version 12.4(15)T10
    64MB CF default
    512DDR DRAM
    My problem right now is,when i tried to configure the IPS feature,the SDM Express ver2.5 doesn't have the IPS tabs that allow me to configure. I noticed and highly suspected that is due to the express version of SDM,instead of the full/enhanced version of SDM. I tried download the full version SDM from Cisco,the file size is 14MB, and my current CF free space is only remaining 7MB.The IOS itself has used up 51MB. So i'm going to advice my customer that running IPS on the router is not possible due to the limited CF size. Can someone who experience in IPS correct me if i'm wrong. I'm fresh in security area.
    PS:i know workaround is to installed CSM on a workstation then to configure and manage this router.
    Thanks

    Hi Collin,
    Thank for your adviced.I did read thru the configuration that you posted. One line which i'm not clear about is that:
    "copy flash:/IOS-S302-CLI.pkg idconf"
    Where is this idconf?Is a flash folder or somewhere?why do we need to copy the signature file to this idconf? Or,my guess,is this idconf referred to "flash:/ips"?
    regards,

  • Cisco 1000Base- LX/LH SFP working with 3560E and 4510R-fiber optical

    Dear all,
         I have 2 module :Cisco 1000Base- LX/LH SFP . Sw 3560E ( Top-Wig ) Sw 4510R . I want to connect 3560E to 4510R by fiber optical (Singer mode -distance 3km ) use module :Cisco 1000Base- LX/LH SFP.
         But when plug module to Sw 3560E (Top- Wig) -Show interface is: " Media card is 1000Base-LX" and plug module to 4510R : " Media Card is 1000Base -LH " . what is this problem ?  Pls help me fix module on 3560E to 1000Base-LH
    Thanks !

    Hi Leolaohoo
    I connected cable to module but green led is not display ( both 3560e and 4510r). 3560e can not connect to 4510r. How is change type module on 3560e from LX to LH ? Because module on 4510r - display is LH
    Thanks !
    -tin nhắn ban đầu-
    Chủ đề: - Re: Cisco 1000Base- LX/LH SFP working with 3560E and 4510R-fiber optical
    Từ: leolaohoo
    Ngày: 24/04/2012 05:19
    leolaohoo created the discussion
    "Re: Cisco 1000Base- LX/LH SFP working with 3560E and 4510R-fiber optical"
    To view the discussion, visit: https://supportforums.cisco.com/message/3618797#3618797

  • Issue with 3560g sfp GLC-SX-MM connect to 2924C

    I have a 3560g switch. Have gig sfp interface [GLC-SX-MM=] and want to connect to to WS-2924C-XL f0/24 fasteth fiber port.
    I have a patch panel in the middle.
    3560g sfp interface [GLC-SX-MM=]   SC   ---------- ST PP  ST   -------------------------   SC  2924C-XL f0/24 fasteth fiber port
    can I make this work? The lights do not come up. The port are configured correctly. I can not hard code the speed on the 3560 int sfp.

    Unfortunately, you can't directly connect a 1GE GLC-SX-MM SFP interface to a 100Base-FX interface.  You will need to swap the SFP on the 3560G with a 100Base-FX SFP (GLC-FE-100FX).
    Cisco 100-Megabit Ethernet SFP Modules  Compatibility Matrix
    <http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL632702.html>
    Hope this helps.
    Tom

  • Recommended IOS XE version for Cisco Catalyst 4500X-16 SFP+ Switch

    Could someone confirm IOS XE version for Cisco Catalyst 4500X-16 SFP+ Switch please.
    It already has 03.06.00.E on it. I am planning to configure VSS on it with similar switch.
    VSS will participate in various Etherchannels (MES).
    Just wondering if there are any known bugs in this IOS XE release.

    Use the Bug Search Tool to look for issues with vss, vsl, etc.
    https://tools.cisco.com/bugsearch/

  • Cisco Nexus 5548UP support SFP-10G-LRM ?

    Hi all, I have a question about Cisco Nexus 5548UP. Is Cisco Nexus 5548UP support SFP-10G-LRM ? Because in CCW, i can't configure the SFP-10G-LRM. There is only SFP-10G-LR, SR, and the others, but there's no LRM. Pelase help me to answer this question. Thanks a lot

    The LRM is s special case transceiver which supports 10 Gbps over older FDDI grade multimode fiber when used with a mode conditioning patch cord. It is not supported on the Nexus 5548UP.
    The SFP-10G-LR is used with single mode fiber for spans up to 10 km in length. It is supported on the 5548UP (and most every platform of Cisco's that takes SFPs).
    Please see the product data sheet here.

  • Cisco 2851 vs 2951

    Can anybody suggest how to find major performance difference between this two routers ? I have small network with 150 users (NAT, DHCP,  few access lists, 2/2MB traffic per user, 40MB peak traffic, static routes  ....nothing special)  and Cisco 2851 works with max 80% CPU utilization. Regarding to the customer will increase teh number of users to around 700 I would like to know if Cisco 2951 will be enough?
    Thank you for any advice or suggestion.
    Boris

    Disclaimer
    The  Author of this posting offers the information contained within this  posting without consideration and with the reader's understanding that  there's no implied or expressed suitability or fitness for any purpose.  Information provided is for informational purposes only and should not  be construed as rendering professional advice of any kind. Usage of this  posting's information is solely at reader's own risk.
    Liability Disclaimer
    In  no event shall Author be liable for any damages whatsoever (including,  without limitation, damages for loss of use, data or profit) arising out  of the use or inability to use the posting's information even if Author  has been advised of the possibility of such damage.
    Posting
    If your routing is only to/from your WAN link, you really only need to size the router to deal with the WAN link (as this normally is the principal bottleneck).
    If your routing is also within the LAN (i.e. between LAN subnets), then you might want to consider also using a L3 switch.
    PS:
    The 2851 is rated at 220 Kpps, the 2951 is rated at 579 Kpps.
    I've attached a Cisco whitepaper for latest ISR performance.

  • CME B-ACD on Cisco 2911 with IOS 15.2(4)M5 not working

    Hi Folks,
    I am currently setting up CME version 9.1 with B-ACD (app-b-acd-aa-3.0.0.2.tcl & app-b-acd-3.0.0.2.tcl), running on
    Cisco 2911 with IOS ver 15.2(4)M5, this is for lab purposes.
    Below is my CME & B-ACD configuration :
    voice service voip
    ip address trusted list
      ipv4 0.0.0.0 0.0.0.0
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
    h323
      h225 listen-port 1820
      no call service stop
    sip
      bind control source-interface Vlan400
      bind media source-interface Vlan400
      registrar server expires max 600 min 60
    voice register global
    mode cme
    source-address 172.25.202.1 port 5060
    max-dn 2
    max-pool 2
    load 9971 sip9971.9-2-2SR1-9
    authenticate register
    timezone 28
    time-format 24
    date-format D/M/Y
    tftp-path flash:
    create profile sync 0004714411607756
    voice register dn  1
    number 3005
    name br2phn2
    voice register dn  2
    number 3006
    name br2phn4
    voice register template  1
    dialplan 1
    voice register dialplan 1
    type 7940-7960-others
    pattern 1 3...
    pattern 2 999
    voice register pool  1
    id mac 1C1D.86C4.0D6D
    type 9971
    number 1 dn 1
    template 1
    dtmf-relay rtp-nte
    username 3005 password cisco
    description 3214-3005
    codec g711ulaw
    voice register pool  2
    id mac 1C1D.86C4.A574
    type 9971
    number 1 dn 2
    template 1
    dtmf-relay rtp-nte
    username 3006 password cisco
    description 3214-3006
    codec g711ulaw
    voice hunt-group 1 parallel
    list 3002,3006
    pilot 3210
    application
    service aa flash:/app-b-acd-aa-3.0.0.2.tcl
      paramspace english index 1
      param number-of-hunt-grps 2
      param handoff-string aa
      paramspace english language en
      param max-time-vm-retry 2
      param aa-pilot 3500
      paramspace english location flash://
      param second-greeting-time 60
      param welcome-prompt _bacd_welcome.au
      param call-retry-timer 15
      param voice-mail 3001
      param max-time-call-retry 90
      param service-name queue
    service aa-drop flash:/app-b-acd-aa-3.0.0.2.tcl
      paramspace english index 1
      param service-name queue
      param drop-through-option 2
      param second-greeting-time 60
      paramspace english language en
      param max-time-vm-retry 2
      param max-time-call-retry 90
      param voice-mail 3001
      paramspace english location flash://
      param aa-pilot 3501
      param number-of-hunt-grps 1
      param handoff-string aa-drop
      param call-retry-timer 15
    service queue flash:/app-b-acd-3.0.0.2.tcl
      param queue-len 15
      param aa-hunt10 3006
      param queue-manager-debugs 1
      param number-of-hunt-grps 2
      param aa-hunt2 3210
    interface Loopback0
    ip address 172.25.110.3 255.255.255.255
    ip ospf network point-to-point
    h323-gateway voip interface
    h323-gateway voip id Spain ipaddr 172.25.110.1 1719
    h323-gateway voip h323-id BR2-RTR
    h323-gateway voip tech-prefix 1#
    h323-gateway voip bind srcaddr 172.25.110.3
    interface Vlan400
    ip address 172.25.202.1 255.255.255.0
    ip pim dense-mode
    dial-peer voice 3500 voip
    service aa
    destination-pattern 3500
    session target ipv4:172.25.110.3
    incoming called-number 3500
    dtmf-relay h245-alphanumeric
    codec g711ulaw
    no vad
    dial-peer voice 3501 voip
    service aa-drop
    destination-pattern 3501
    session target ipv4:172.25.110.3
    incoming called-number 3501
    dtmf-relay h245-alphanumeric
    codec g711ulaw
    no vad
    telephony-service
    no auto-reg-ephone
    max-ephones 2
    max-dn 2 no-reg both
    ip source-address 172.25.110.3 port 2000
    cnf-file location flash:
    load 7965 term65.default.loads
    time-zone 28
    time-format 24
    date-format dd-mm-yy
    max-conferences 8 gain -6
    moh "music-on-hold.au"
    web admin system name admin password cisco
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 14 2014 05:54:44
    ephone-template  1
    softkeys connected  Endcall Hold Park Trnsfer Acct Flash
    ephone-dn  1  octo-line
    number 3001 no-reg both
    description 3214-3001
    name br2phn1
    ephone-dn  2  octo-line
    number 3002 no-reg both
    description 3214-3002
    name br2phn3
    ephone  1
    device-security-mode none
    mac-address 189C.5DB6.D303
    ephone-template 1
    max-calls-per-button 5
    busy-trigger-per-button 3
    type 7965
    button  1:1
    ephone  2
    device-security-mode none
    description 3214-3002
    mac-address 984B.E194.FDDD
    ephone-template 1
    max-calls-per-button 5
    busy-trigger-per-button 3
    type 7960
    button  1:2
    Problem :
    1. When I test call from CME Phone both SIP and SCCP Phone by dial 3500 or 3501, I get the busy tone.
    2. Debug voip dial-peer, match with dial-peer voice 3500 for (aa service) & 3501 for (aa-drop service).
    3. Debug voice application script, show nothing.
    Is there something wrong with my configuration ?
    Rgds
    Novri

    Hi Novriadi,
    In your configuration
    service aa flash:/app-b-acd-aa-3.0.0.2.tcl
    service queue flash:/app-b-acd-3.0.0.2.tcl
    paramspace english location flash://
    Remove "/" and "//" from the configuration
    Then use the call application voice load command in privileged EXEC mode to reload the scripts.
    Router# call application voice load aa
    Router# call application voice load queue
    Router# call application voice load aa-drop
    You can refer to following document as well for more info
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/bacd/configuration/guide/cme40tcl/40bacd.html#wp1018270
    Please find the sample configuration that is required to configure b-acd in CME for reference.
    telephony-service
    moh music-on-hold.au
    multicast moh 239.1.1.1 port 2000
    application
    service queue flash:app-b-acd-2.1.0.0.tcl
      param number-of-hunt-grps 2
      param aa-hunt2 1111
      param aa-hunt3 1222
      param queue-len 15
      param queue-manager-debugs 1
    service aa flash:app-b-acd-aa-2.1.0.0.tcl
      paramspace english index 1
      paramspace english language en
      paramspace english location flash:
      param service-name queue
      param handoff-string aa
      param aa-pilot 8005550123
      param welcome-prompt _bacd_welcome.au
      param number-of-hunt-grps 2
      param dial-by-extension-option 1
      param second-greeting-time 60
      param call-retry-timer 15
      param max-time-call-retry 700
      param max-time-vm-retry 2
      param voice-mail 5003
    dial-peer voice 222 voip
    service aa
    destination-pattern 8005550123
    session target ipv4:192.168.1.1
    incoming called-number 8005550123
    dtmf-relay h245-alphanumeric
    codec g711ulaw
    no vad
    Thanks & Regards,
    Mudit Mathur

  • Cisco UCM with Third Party Contact Center Solution

    Hi all, hope everyone is well.
    Anyone out there running Cisco UCM with a third party contact center solution ? would love to hear your experience on this subject.
    Thanks in advance !!
    Danny

    I have not heard of any sucessful stories, which vendor are you considering and what would you not go with UCCE/UCCX?
    I used to work for Rockwell (Aspect today) which attempted to integrate their Business Contact Solution with CUCM (back on 3.3) and it worked OK for low volume calls, but never had any customer adoption.
    I have not heard of any other known ACD vendors integrating with CUCM.
    Chris

  • Using Cisco WCS with Microsoft IAS

    Hi.
    I have two 5508 and WCS 7.0.172. I want to user Active Directory users credintals to login on ther WCS. Have a configurated NPS role on server with windows 2008 r2.
    I have read this http://zmq503o1.wordpress.com/2008/01/06/using-cisco-wcs-with-microsoft-ias/ and done the same.
    I dont't agree with "on the "Encryption" tab and clear all the checkboxes except "No encryption" - wants an encryption connection but this didn't work till in user's properites in AD permit "Reversible encryption". This is not what that I want.  Would I need to generate ssl-cert for the wcs as wroted this?http://www.cisco.com/en/US/docs/wireless/wcs/7.0MR1/configuration/guide/hard.html#wp1042471
    or doing smth else? thx

    Camera is only supported for use with CUVA. Any other application attempting to utilize the camera is not tested and is not supported.

  • Cisco IronPort with On Premise Exchange 2013

    Hello All
    The company I work for is in the process of starting an on premise Exchange 2007 to Exchange 2013 migration.
    Most of the issues I don't think I'll have an issue with; however, where I am not finding much info is in regards to other companies using Cisco IronPort with Exchange 2013.
    SO, I have two questions within this topic...
    One, is anyone using Cisco IronPort with Exchange 2013 (on premise) out here?
    Two, my manager is very controlling.  I am the Exchange Admin; however, anything having to do with this IronPort thing with regards to Exchange HE has to do it. So, if anyone is familiar with this IronPort thing... How much work on the IronPort is going
    to have to be done during this migration to keep things going?

    It shouldn't be any different with Exchange 2013 than it is with Exchange 2007.
    Ed Crowley MVP "There are seldom good technological solutions to behavioral problems."

  • Cisco 1700 with MP-BGP and VRF support

    I have a Cisco 1721 with MP-BGP Support, you can create VRFs with it and every other MPLSVPN feature, but the commands for MPLS switching are not supported like Router(config-if)mpls ip , I read in some forums that you can create MPLS VPN without enabling MPLS at all, just with MPBGP, but I couldn't do it myself, Can someone tell me how to make it work or what can I do with a Cisco 1721 that supports MP-BGP?
    thanks in advance

    Here is an example. Take care about overhead for packets like VoIP. The overhead is 88 bytes.
    The packet semms something like that.
    IpHeader-pub@ - NAT-Tudp4500 - ESP - IpHeader-priv@(vrf discriminator) - GRE - Original IP Header - Data - Esp Trailer.
    In this case you neet tunnel-mode because you use
    private @ in order to determine vrf (vrf discriminator).
    This is a LAB config, all other security parameters you need on a router are not configured. If you add access-list on the external interface of REMOTE you have to understand every encapsulation step in order to well tune it.
    Good reading.
    The PPT draw shows physically and logically views.
    PS, take care about fragmentation issues, the problematic is still not well managed by the routers, I could not made Tunnel-path-mtu discovery work with vrf's. The workaround is to fragment packets. It's not good for performance but actually there is no other solution concerning that.
    Kind Regards
    Miguel

  • Cisco 2621 with 2821

    I have a Cisco 2621 with 2FXS and 2FXO for my landlines, can I setup my 2821 to use my 2621 to make outside calls?
    Sent from Cisco Technical Support iPhone App

    That should work in my opinion. The 2821 is running CCME? But is that worth the effort? Can't you place the VWICs into the 2821 instead in the 2621?
    Don't stop after you've improved your network! Improve the world by lending money to the working poor:
    http://www.kiva.org/invitedby/karsteni

  • Does Cisco 3845 with NM-16A/S support OIR feature or Hot swap for this NM.

    Dear Sir
    My customer would like to implement Cisco 3845 with NM-16A/S x 4. I found that Cisco 3845 support OIR function but I am not sure OIR function that Cisco 3845 support, it support with which NM models. Can anyone tell me that NM-16A/S on Cisco 3845 support OIR function on this NM or not.
    Thank you very much
    Wisit

    Hi,
    From what I have read from the following document.
    http://www.cisco.com/en/US/products/ps5855/products_installation_guide_chapter09186a00802ccf1d.html
    Network Modules
    Network modules install directly into slots in the rear of the router. The Cisco 3845 router supports online insertion and removal (OIR, or hot swap) of network modules. The Cisco 3825 router does not support OIR.
    Caution The Cisco 3845 router supports OIR with similar modules only. If you remove a network module, along with any installed WAN or voice interface cards, install another module and card combination exactly like it.
    Interface Cards
    Cisco 3800 series routers do not support OIR (hot swap) of interface cards inserted directly into router slots. You must turn off the router before installing or removing an interface card.
    The Cisco 3825 router and the Cisco 3845 router each provide four interface card slots, labeled on the rear panel by HWIC and a number. Each slot can be occupied by one single-wide WIC, VIC, VWIC, or HWIC.
    Hope this helps
    Sarb

Maybe you are looking for