Cisco 2960 Hang Up
Hi guys,
Need some help for my cisco switch 2960. It was brand new. We already configured it and mounted it. we can already ssh the device but the weird thing is, there are times that we cannot access it and have it restarted. There are still no connections attached to it other than the management. my IOS version is 12.2(55)SE8.
Thanks,
Glen
For something like this I would first upgrade to the latest recommend IOS release. This might resolve the issue.
https://software.cisco.com/download/release.html?mdfid=282867574&flowid=46696&softwareid=280805680&release=15.0.2-SE6&relind=AVAILABLE&rellifecycle=MD&reltype=latest
this link recommends using 15.0.2-SE6(MD) as the IOS. You'll see a 'suggested' field on the left pane. Try putting this IOS on the switch. If a memory leak is your issue a new IOS should resolve.
Similar Messages
-
Configuring Port Channel on Cisco 2960S-48LPS-L
When I try to move port channel connections to two of the SFP ports on our Cisco 2960S switch, one of the connections fail.
I am using two GBics, both are the same, GLC-T-A 1000Base-T.
The port channel work fine when I use g1/0/47 and 48.
The port channel work fine when using g1/0/48 and SFP 1/0/49
Port channel does not work when using SFP 1/0/49 and SFP 1/0/50.Cisco C2960S software version: 12.2(55)SE7. Using C2960S-UNIVERSALK9-M.
Port configurations for g1/0/48 - 51:
interface GigabitEthernet1/0/49
description Trunk to Cisco Core
switchport mode trunk
srr-queue bandwidth share 1 30 35 5
priority-queue out
mls qos trust cos
macro description cisco-switch
auto qos trust
spanning-tree link-type point-to-point
channel-group 2 mode on
When working, both ports show green status lights.
ort Name Status Vlan Duplex Speed Type
Po2 Trunk to Core connected trunk a-full a-1000
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
* Port-channel2 0 0 0 0 8390000 909 970000 551 0
Age of the Port-channel = 0d:10h:57m:35s
Logical slot/port = 5/2 Number of ports = 2
GC = 0x00000000 HotStandBy port = null
Port state = Port-channel Ag-Inuse
Protocol = -
Port security = Disabled
Ports in the Port-channel:
Index Load Port EC state No of bits
------+------+------+------------------+-----------
0 00 Gi1/0/47 On 0
0 00 Gi1/0/49 On 0
When not working, one port shows green, then other port status light is off.
GigabitEthernet1/0/49 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 3c0e.233f.a531 (bia 3c0e.233f.a531)
Description: Trunk to Cisco Core
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:09, output 00:00:19, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1954000 bits/sec, 213 packets/sec
5 minute output rate 38000 bits/sec, 16 packets/sec
2935639 packets input, 880524431 bytes, 0 no buffer
Received 2211794 broadcasts (310067 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 310067 multicast, 0 pause input
0 input packets with dribble condition detected
370489 packets output, 66729219 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
GigabitEthernet1/0/50 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 3c0e.233f.a532 (bia 3c0e.233f.a532)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex, Auto-speed, link type is auto, media type is Not Present
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
--More-- 0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Let me know if you need more info. -
Cisco 2960-X & ISE accounting- username Radius attribute missing
Hi,
I'm facing an issue with cisco 2960 switch radius accounting with Cisco ISE1.2.1 .here is my senario:
- Username (vendor1) is configured in ISE local database, under group (VENDOR)
- Authentication protocol : wired MAB
- Authentication method : webauth using guest portal , the user is a vendor , so no dot1x configured on his NIC .
the problem is that , the switch is not sending the username as a part of radius attribute , in the authentication log , the username shown as the MAC address of the user machine , therefor , I can not configure my authorization condition using internaluser:Name Equal vendor1
while if I configure the condition using the identity group condition IdentityGroup:Name Equal VENDOR , it works .
The same configuration is working on 3750 switch with no issue .
Here is my Switch config:
aaa authentication login default local
aaa authentication dot1x default group radius
aaa authorization network default group radius
aaa authorization auth-proxy default group radius
aaa accounting auth-proxy default start-stop group radius
aaa accounting dot1x default start-stop group radius
aaa accounting update periodic 5
username admin password
username radius-test password
aaa server radius dynamic-author
client 172.16.2.20 server-key 7 04490A0206345F450C00
client 172.16.2.21 server-key 7 03165A0F0F1A32474B10
radius server ISE-RADIUS-1
address ipv4 172.16.2.20 auth-port 1812 acct-port 1813
automate-tester username radius-test idle-time 15
key 7 111B18011E0718070133
radius server ISE-RADIUS-2
address ipv4 172.16.2.21 auth-port 1812 acct-port 1813
automate-tester username radius-test idle-time 15
key 7 0214055F02131C2A4957
radius-server attribute 6 on-for-login-auth
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server attribute 31 mac format ietf upper-case
radius-server attribute 31 send nas-port-detail
radius-server dead-criteria time 5 tries 3
radius-server vsa send accounting
radius-server vsa send authentication
any help !!!Thanks for your reply , I know what's MAB , if you read my explanation again , i mentioned that the user is authenticated in the guest portal which mean that I have web authentication , and it is working fine .. The only issue is that I can not use the vendor1 username as part of authorization condition and this is because the switch is not sending the radius attribute type 1 to the ISE , thus , on the ise authentication log the MAC address of the client machine is shown as a username not the actual username ( vendor1)
as I mentioned also , I have exactly the same setup with ise 1.2 and 3750 switch and I do not have this issue .I experience this with 2960x only . -
IEEE 802.1x with EAP-TLS issue in cisco 2960
In My Cisco 2960 switch is not working with EAP-TLS mechanism of 802.1x but its works well with other protocols like EAP-PEAP or MAC Address authentication.
Below is the configuration
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authentication dot1x default group radius
aaa authorization commands 15 default group tacacs+ local
aaa authorization network default group radius
aaa authorization configuration default group radius
aaa accounting update periodic 30
aaa accounting dot1x default start-stop group radius
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 0 default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting network default start-stop group tacacs+
aaa accounting connection default start-stop group tacacs+
aaa accounting system default start-stop group tacacs+
interface FastEthernet0/1
switchport access vlan 11
switchport mode access
speed 100
duplex full
authentication order dot1x mab webauth
authentication port-control auto
mab
dot1x pae authenticator
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
spanning-tree portfast
spanning-tree bpduguard enable
Can anyone suggest me ?Thanks for the reply jatin.
I have a client on the interface fa0/1 with a valid client certificate. And have a debug logs as below
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Interface state changed to UP
*Mar 8 00:03:06.266: AAA/BIND(000001C7): Bind i/f
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: initial state auth_initialize has enter
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_initialize_enter called
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: during state auth_initialize, got event 0(cfg_auto)
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_initialize -> auth_disconnected
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_disconnected_enter called
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has enter
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_initialize_enter called
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has idle
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: during state auth_bend_initialize, got event 16383(idle)
*Mar 8 00:03:06.266: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Created a client entry (0xB0000DBA)
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Dot1x authentication started for 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.266: dot1x-ev:DOT1X Supplicant not enabled on FastEthernet0/1
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0xB0000DBA
*Mar 8 00:03:06.274: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:06.274: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_enter called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_authenticating_action called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): Posting AUTH_START for 0xB0000DBA
*Mar 8 00:03:06.274: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:06.274: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.274: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.274: EAPOL pak dump Tx
*Mar 8 00:03:06.274: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:06.274: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:06.274: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_request_action called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): queuing an EAPOL pkt on Auth Q
*Mar 8 00:03:06.794: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.794: EAPOL pak dump rx
*Mar 8 00:03:06.794: EAPOL Version: 0x1 type: 0x1 length: 0x0000
*Mar 8 00:03:06.794: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 0,TYPE= 0,LEN= 0
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0101.0000
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Couldn't find the supplicant in the list
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): New client detected, notifying AuthMgr
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Sending event (0) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): Received an EAPOL-Start packet
*Mar 8 00:03:06.794: EAPOL pak dump rx
*Mar 8 00:03:06.794: EAPOL Version: 0x1 type: 0x1 length: 0x0000
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting EAPOL_START on Client 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth Fa0/1: during state auth_authenticating, got event 4(eapolStart)
*Mar 8 00:03:06.794: @@@ dot1x_auth Fa0/1: auth_authenticating -> auth_aborting
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_exit called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_enter called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): 802.1x method gets the go ahead from Auth Mgr for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.794: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting AUTH_ABORT for 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 1(authAbort)
*Mar 8 00:03:06.794: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_initialize
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_initialize_enter called
*Mar 8 00:03:06.794: dot1x_auth_bend Fa0/1: idle during state auth_bend_initialize
*Mar 8 00:03:06.794: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting !AUTH_ABORT on Client 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth Fa0/1: during state auth_aborting, got event 20(no_eapolLogoff_no_authAbort)
*Mar 8 00:03:06.794: @@@ dot1x_auth Fa0/1: auth_aborting -> auth_restart
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_exit called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Resetting the client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_restart_action called
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:06.802: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:06.802: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:06.811: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_enter called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_authenticating_action called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting AUTH_START for 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:06.811: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.811: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.811: EAPOL pak dump Tx
*Mar 8 00:03:06.811: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:06.811: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_request_action called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:06.811: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.811: EAPOL pak dump rx
*Mar 8 00:03:06.811: EAPOL Version: 0x1 type: 0x0 length: 0x0022
*Mar 8 00:03:06.811: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 1,LEN= 34
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0022
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:06.811: EAPOL pak dump rx
*Mar 8 00:03:06.811: EAPOL Version: 0x1 type: 0x0 length: 0x0022
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:06.811: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:06.811: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:06.819: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:06.819: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:06.819: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:06.819: RADIUS(000001C7): sending
*Mar 8 00:03:06.819: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:06.819: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/83, len 251
*Mar 8 00:03:06.819: RADIUS: authenticator A1 79 FA E5 F4 B7 7F 4F - 2B 73 3A 0D 1F D8 89 20
*Mar 8 00:03:06.819: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:06.819: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:06.819: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:06.819: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:06.819: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:06.819: RADIUS: EAP-Message [79] 36
*Mar 8 00:03:06.819: RADIUS: 02 01 00 22 01 68 6F 73 74 2F 44 30 39 30 32 4D 41 4C 4C 30 ["host/D0902MALL0]
*Mar 8 00:03:06.819: RADIUS: 30 35 2E 49 4E 2E 69 6E 74 72 61 6E 65 74 [ 05.IN.intranet]
*Mar 8 00:03:06.819: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.819: RADIUS: D6 6F 7B CD 36 46 5E F6 90 6F 85 A8 BD BD AE D8 [ o{6F^o]
*Mar 8 00:03:06.819: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:06.819: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:06.819: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:06.819: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:06.819: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:06.819: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:06.819: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:06.819: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:06.819: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:06.861: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar 8 00:03:06.903: RADIUS: Received from id 1645/83 10.26.13.59:1812, Access-Challenge, len 76
*Mar 8 00:03:06.903: RADIUS: authenticator 7B 1C DC CA A8 92 E9 34 - 17 86 25 2F 9D 7E 63 96
*Mar 8 00:03:06.903: RADIUS: EAP-Message [79] 8
*Mar 8 00:03:06.903: RADIUS: 01 02 00 06 0D 20 [ ]
*Mar 8 00:03:06.903: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.903: RADIUS: DD F3 7B 33 37 6D 40 BD F3 D2 78 DF F1 14 4D E4 [ {37m@xM]
*Mar 8 00:03:06.903: RADIUS: State [24] 30
*Mar 8 00:03:06.903: RADIUS: 00 7D 00 9B 00 C1 00 40 ED B8 45 00 FC DD 50 2E DC 0E E6 03 FC 7B AD 4C B7 E7 B1 70 [ }@EP.{Lp]
*Mar 8 00:03:06.911: RADIUS(000001C7): Received from id 1645/83
*Mar 8 00:03:06.911: RADIUS/DECODE: EAP-Message fragments, 6, total 6 bytes
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:06.911: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:06.911: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.911: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.911: EAPOL pak dump Tx
*Mar 8 00:03:06.911: EAPOL Version: 0x3 type: 0x0 length: 0x0006
*Mar 8 00:03:06.911: EAP code: 0x1 id: 0x2 length: 0x0006 type: 0xD
*Mar 8 00:03:06.911: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:06.920: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.920: EAPOL pak dump rx
*Mar 8 00:03:06.920: EAPOL Version: 0x1 type: 0x0 length: 0x0069
*Mar 8 00:03:06.920: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 105
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0069
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:06.920: EAPOL pak dump rx
*Mar 8 00:03:06.920: EAPOL Version: 0x1 type: 0x0 length: 0x0069
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:06.920: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:06.920: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:06.920: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:06.920: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:06.920: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:06.920: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:06.920: RADIUS(000001C7): sending
*Mar 8 00:03:06.920: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:06.920: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/84, len 352
*Mar 8 00:03:06.920: RADIUS: authenticator 41 72 8D 6A B4 72 19 84 - 1B C8 33 F7 95 DD 07 BC
*Mar 8 00:03:06.928: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:06.928: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:06.928: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:06.928: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:06.928: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:06.928: RADIUS: EAP-Message [79] 107
*Mar 8 00:03:06.928: RADIUS: 02 02 00 69 0D 80 00 00 00 5F 16 03 01 00 5A 01 00 00 56 03 01 52 C5 45 4F 07 CA B3 29 50 A7 CE 40 76 B6 BD F0 50 D4 CE 9A 8A 02 C4 3D 40 35 B5 F0 E1 E2 75 [i_ZVREO)P@vP=@5u]
*Mar 8 00:03:06.928: RADIUS: 50 00 00 18 00 2F 00 35 00 05 00 0A C0 13 C0 14 C0 09 C0 0A 00 32 00 38 00 13 00 04 01 00 00 15 FF 01 00 01 00 00 0A 00 06 00 04 00 17 00 18 00 0B 00 02 01 00 [ P/528]
*Mar 8 00:03:06.928: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.928: RADIUS: A3 28 CE 27 20 C0 D6 2C 11 01 D6 61 1F C3 6F 03 [ (' ,ao]
*Mar 8 00:03:06.928: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:06.928: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:06.928: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:06.928: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:06.928: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:06.928: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:06.928: RADIUS: State [24] 30
*Mar 8 00:03:06.928: RADIUS: 00 7D 00 9B 00 C1 00 40 ED B8 45 00 FC DD 50 2E DC 0E E6 03 FC 7B AD 4C B7 E7 B1 70 [ }@EP.{Lp]
*Mar 8 00:03:06.928: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:06.928: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:06.928: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:07.004: RADIUS: Received from id 1645/84 10.26.13.59:1812, Access-Challenge, len 1188
*Mar 8 00:03:07.004: RADIUS: authenticator 7B 52 29 05 7E C3 EF 8E - 13 38 30 03 4B 65 64 0F
*Mar 8 00:03:07.004: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.004: RADIUS: 01 03 04 56 0D C0 00 00 05 78 16 03 01 00 51 02 00 00 4D 03 01 52 C5 45 4F 0F 04 37 77 A0 C2 68 66 4E 45 92 AB 3D 7F 94 70 AF 36 [VxQMREO7whfNE=p6]
*Mar 8 00:03:07.004: RADIUS: 1D C5 17 23 5C F1 FA CA 60 B0 20 A5 48 16 D5 3F F9 B0 FF 38 1D D5 13 B3 88 13 06 EF DC 87 5C AE 17 E7 7E 80 84 21 58 64 F7 A6 36 00 35 00 00 05 FF 01 00 01 00 16 03 01 02 1C 0B 00 02 18 00 02 15 00 02 12 30 82 02 0E 30 [#\` H?8\~!Xd6500]
*Mar 8 00:03:07.004: RADIUS: 82 01 77 A0 03 02 01 02 02 09 00 88 7A CB 35 3F 1E 3E 62 30 0D 06 09 2A 86 48 86 F7 0D 01 01 05 05 00 30 2F 31 15 30 13 06 03 55 04 03 13 0C 53 50 [wz5?>b0*H0/10USP]
*Mar 8 00:03:07.004: RADIUS: 49 4E 41 56 44 30 30 30 30 34 31 16 30 14 06 03 55 04 0A 13 0D 50 6F 6C [INAVD0000410UPol]
*Mar 8 00:03:07.004: RADIUS: 69 63 79 4D 61 6E 61 67 65 72 30 1E 17 0D 31 33 30 38 32 [icyManager013082]
*Mar 8 00:03:07.004: RADIUS: 37 30 37 32 34 33 30 5A 17 0D 31 34 30 38 32 37 30 37 [7072430Z14082707]
*Mar 8 00:03:07.004: RADIUS: 32 34 33 30 5A 30 2F 31 15 30 13 06 03 55 04 03 13 0C 53 50 49 4E 41 56 [2430Z0/10USPINAV]
*Mar 8 00:03:07.004: RADIUS: 44 30 30 [ D00]
*Mar 8 00:03:07.004: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.004: RADIUS: 30 30 34 31 16 30 14 06 03 55 04 0A 13 0D 50 6F 6C 69 63 79 4D 61 6E 61 [00410UPolicyMana]
*Mar 8 00:03:07.004: RADIUS: 67 65 72 30 81 9F 30 0D 06 09 2A 86 48 86 F7 0D 01 01 01 05 00 03 81 8D 00 30 81 89 02 81 81 00 C9 B9 03 65 83 EB 39 86 14 BC 95 7B DB 07 7E C5 8A D7 DA C7 8A CA 5A 88 6E 0B 93 06 35 57 [ger00*H0e9{~Zn5W]
*Mar 8 00:03:07.012: RADIUS: 6E DE 93 CD C9 FE 8E 9F E1 5F A9 04 5C BD A9 AD 5A 04 6E 35 47 76 A1 58 E5 C4 32 D7 49 9E 17 75 20 C6 6F 45 40 [n_\Zn5GvX2Iu oE@]
*Mar 8 00:03:07.012: RADIUS: AC EF 40 6D 15 38 F9 C2 28 7E C9 68 37 52 3B BF F4 C1 5E B8 BA 46 68 43 79 B1 65 66 [@m8(~h7R;^FhCyef]
*Mar 8 00:03:07.012: RADIUS: 9E 58 ED EC 8C 95 A2 D8 BF AA 77 AC 85 90 E3 AB C6 27 3A A2 22 AC 1C 48 B3 BF BE F7 85 CF 5C BB 2D 02 03 01 00 01 A3 32 30 30 30 0F 06 03 55 1D 11 04 08 30 06 87 04 0A 1A 0D 3B 30 [Xw':"H\-2000U0;0]
*Mar 8 00:03:07.012: RADIUS: 1D 06 03 55 1D 25 04 16 30 14 06 08 2B 06 01 05 05 07 03 01 06 08 2B 06 01 05 05 07 03 03 30 0D 06 09 2A 86 48 86 F7 0D 01 01 [ U?0++0*H]
*Mar 8 00:03:07.012: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.012: RADIUS: 05 05 00 03 81 81 00 C4 46 3E 38 3D 53 0F 28 34 C1 A6 ED DC 70 76 9B 70 6B A8 95 7C 44 8E 7D 6E D6 8B 6D [F>8=S(4pvpk|D}nm]
*Mar 8 00:03:07.012: RADIUS: 90 49 83 06 E4 BF 68 2F 9D 77 78 A3 76 76 19 84 AD 26 3F F3 ED AA 88 52 35 0E 35 DD 00 E5 96 88 44 30 79 A0 71 [Ih/wxvv&?R55D0yq]
*Mar 8 00:03:07.012: RADIUS: 8D 25 3E 77 A0 E0 43 92 33 55 40 E1 C8 EE 88 11 25 E2 70 28 11 6C 5A 4E 3D F1 93 57 0A 6F [?>wC3U@?p(lZN=Wo]
*Mar 8 00:03:07.012: RADIUS: 36 51 72 04 08 C0 C0 DF F0 94 A9 F7 A1 05 C8 37 D6 F8 D4 9C 20 1A 7B CD 2C 17 83 7B 8E 20 F7 2D B6 16 03 01 02 FC 0D 00 02 F4 03 01 02 40 02 EE 00 63 30 61 31 0B 30 [6Qr7 {,{ -@c0a10]
*Mar 8 00:03:07.012: RADIUS: 09 06 03 55 04 06 13 02 55 53 31 15 30 13 06 03 55 04 0A 13 0C 44 69 67 69 43 65 72 74 20 49 [UUS10UDigiCert I]
*Mar 8 00:03:07.012: RADIUS: 6E 63 31 19 30 17 06 03 55 04 0B 13 10 77 77 77 2E 64 69 67 69 63 65 72 [nc10Uwww.digicer]
*Mar 8 00:03:07.012: RADIUS: 74 2E 63 6F 6D 31 20 30 1E 06 03 55 04 03 13 17 44 69 67 69 43 65 72 [t.com1 0UDigiCer]
*Mar 8 00:03:07.012: RADIUS: 74 20 47 6C 6F 62 61 6C 20 52 6F 6F 74 20 43 41 [t Global Root CA]
*Mar 8 00:03:07.012: RADIUS: 00 48 [ H]
*Mar 8 00:03:07.012: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.012: RADIUS: 30 46 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E 74 72 61 6E 65 74 31 [0F10&,dintranet1]
*Mar 8 00:03:07.020: RADIUS: 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 16 30 14 06 03 55 04 03 13 0D 49 6E 64 69 61 20 52 [0&,dIN10UIndia R]
*Mar 8 00:03:07.020: RADIUS: 6F 6F 74 20 43 41 00 4A 30 48 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E [oot CAJ0H10&,din]
*Mar 8 00:03:07.020: RADIUS: 74 72 61 6E 65 74 31 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 18 30 16 06 03 55 [tranet10&,dIN10U]
*Mar 8 00:03:07.020: RADIUS: 04 03 13 0F 45 6E 74 65 72 70 72 69 73 65 20 43 41 2D 31 00 4D [Enterprise CA-1M]
*Mar 8 00:03:07.020: RADIUS: 30 4B 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E 74 72 61 6E 65 74 31 [0K10&,dintranet1]
*Mar 8 00:03:07.020: RADIUS: 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 1B 30 19 06 03 55 04 03 13 12 49 4E 2D 53 50 49 4E [0&,dIN10UIN-SPIN]
*Mar 8 00:03:07.020: RADIUS: 43 52 54 30 30 30 30 33 2D 43 41 00 D5 30 81 D2 31 0B 30 09 06 03 55 04 06 13 02 55 [CRT00003-CA010UU]
*Mar 8 00:03:07.020: RADIUS: 53 31 13 30 11 06 03 55 04 [ S10U]
*Mar 8 00:03:07.020: RADIUS: EAP-Message [79] 100
*Mar 8 00:03:07.020: RADIUS: 08 0C 0A 43 61 6C 69 66 6F 72 6E 69 61 31 12 30 10 06 03 55 04 07 0C 09 53 75 6E [California10USun]
*Mar 8 00:03:07.020: RADIUS: 6E 79 76 61 6C 65 31 17 30 15 06 03 55 04 0A 0C 0E 41 72 75 62 61 20 4E [nyvale10UAruba N]
*Mar 8 00:03:07.020: RADIUS: 65 74 77 6F 72 6B 73 31 40 30 3E 06 03 55 04 03 0C 37 43 6C 65 [etworks1@0>U7Cle]
*Mar 8 00:03:07.020: RADIUS: 61 72 50 61 73 73 20 4F 6E 62 6F 61 72 64 20 4C [arPass Onboard L]
*Mar 8 00:03:07.020: RADIUS: 6F 63 61 6C 20 43 65 72 74 69 [ ocal Certi]
*Mar 8 00:03:07.020: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.020: RADIUS: 12 75 40 41 6F 40 6B 6F A5 FE AB 85 F3 B3 CF A4 [ u@Ao@ko]
*Mar 8 00:03:07.020: RADIUS: State [24] 30
*Mar 8 00:03:07.020: RADIUS: 00 6F 00 51 00 4B 00 6E EE B8 45 00 4B AA 6B A9 B6 D6 C8 CC 48 1A 91 99 7F 77 D3 C1 [ oQKnEKkHw]
*Mar 8 00:03:07.029: RADIUS(000001C7): Received from id 1645/84
*Mar 8 00:03:07.029: RADIUS/DECODE: EAP-Message fragments, 253+253+253+253+98, total 1110 bytes
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:07.037: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:07.037: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.037: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:07.037: EAPOL pak dump Tx
*Mar 8 00:03:07.037: EAPOL Version: 0x3 type: 0x0 length: 0x0456
*Mar 8 00:03:07.037: EAP code: 0x1 id: 0x3 length: 0x0456 type: 0xD
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:07.037: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:07.037: EAPOL pak dump rx
*Mar 8 00:03:07.037: EAPOL Version: 0x1 type: 0x0 length: 0x0006
*Mar 8 00:03:07.037: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 6
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0006
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:07.037: EAPOL pak dump rx
*Mar 8 00:03:07.037: EAPOL Version: 0x1 type: 0x0 length: 0x0006
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:07.037: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:07.037: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:07.037: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:07.046: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:07.046: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:07.046: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:07.046: RADIUS(000001C7): sending
*Mar 8 00:03:07.046: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:07.046: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/85, len 253
*Mar 8 00:03:07.046: RADIUS: authenticator 1C D7 6D 40 A3 D6 BA B1 - A7 E6 70 DA 32 83 2E 19
*Mar 8 00:03:07.046: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:07.046: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:07.046: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:07.046: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:07.046: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:07.046: RADIUS: EAP-Message [79] 8
*Mar 8 00:03:07.046: RADIUS: 02 03 00 06 0D 00
*Mar 8 00:03:07.046: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.046: RADIUS: 73 1D 89 5C 66 19 32 B6 63 C2 64 C1 04 42 A9 F9 [ s\f2cdB]
*Mar 8 00:03:07.046: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:07.046: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:07.046: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:07.046: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:07.046: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:07.046: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:07.046: RADIUS: State [24] 30
*Mar 8 00:03:07.046: RADIUS: 00 6F 00 51 00 4B 00 6E EE B8 45 00 4B AA 6B A9 B6 D6 C8 CC 48 1A 91 99 7F 77 D3 C1 [ oQKnEKkHw]
*Mar 8 00:03:07.046: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:07.046: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:07.046: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:07.113: RADIUS: Received from id 1645/85 10.26.13.59:1812, Access-Challenge, len 378
*Mar 8 00:03:07.113: RADIUS: authenticator 1A 85 26 09 58 84 BC D4 - E0 A9 E3 C0 25 31 2D 31
*Mar 8 00:03:07.113: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.121: RADIUS: 01 04 01 32 0D 00 66 69 63 61 74 65 20 41 75 74 68 6F 72 69 74 [2ficate Authorit]
*Mar 8 00:03:07.121: RADIUS: 79 20 28 53 69 67 6E 69 6E 67 29 31 3F 30 3D 06 09 2A [y (Signing)1?0=*]
*Mar 8 00:03:07.121: RADIUS: 86 48 86 F7 0D 01 09 01 16 30 64 36 62 62 34 66 37 30 2D 66 34 31 32 2D [H0d6bb4f70-f412-]
*Mar 8 00:03:07.121: RADIUS: 34 35 35 32 2D 61 65 65 32 2D 63 37 61 30 32 36 [4552-aee2-c7a026]
*Mar 8 00:03:07.121: RADIUS: 66 62 61 32 31 38 40 65 78 61 6D 70 6C 65 2E 63 [[email protected]]
*Mar 8 00:03:07.121: RADIUS: 6F 6D 00 CB 30 81 C8 31 0B 30 09 06 03 55 04 06 13 02 55 53 31 13 30 11 06 03 55 04 08 0C 0A 43 61 6C 69 66 [om010UUS10UCalif]
*Mar 8 00:03:07.121: RADIUS: 6F 72 6E 69 61 31 12 30 10 06 03 55 04 07 0C 09 53 75 6E 6E 79 76 61 6C [ornia10USunnyval]
*Mar 8 00:03:07.121: RADIUS: 65 31 17 30 15 06 03 55 04 0A 0C 0E 41 72 75 62 61 20 4E 65 74 77 6F 72 [e10UAruba Networ]
*Mar 8 00:03:07.121: RADIUS: 6B 73 31 36 30 34 06 03 55 04 03 0C 2D 43 6C 65 61 72 50 61 73 [ks1604U-ClearPas]
*Mar 8 00:03:07.121: RADIUS: 73 20 4F 6E 62 6F 61 72 64 20 4C 6F 63 61 6C 20 [s Onboard Local ]
*Mar 8 00:03:07.121: RADIUS: 43 65 72 74 69 66 69 63 61 74 65 20 41 75 74 68 [Certificate Auth]
*Mar 8 00:03:07.121: RADIUS: 6F 72 69 74 79 31 3F 30 3D 06 09 2A 86 48 86 F7 0D 01 09 01 16 [ ority1?0=*H]
*Mar 8 00:03:07.121: RADIUS: EAP-Message [79] 55
*Mar 8 00:03:07.121: RADIUS: 30 64 36 62 62 34 66 37 30 2D 66 34 31 32 2D 34 [0d6bb4f70-f412-4]
*Mar 8 00:03:07.121: RADIUS: 35 35 32 2D 61 65 65 32 2D 63 37 61 30 32 36 66 [552-aee2-c7a026f]
*Mar 8 00:03:07.121: RADIUS: 62 61 32 31 38 40 65 78 61 6D 70 6C 65 2E 63 6F [[email protected]]
*Mar 8 00:03:07.121: RADIUS: 6D 0E 00 00 00 [ m]
*Mar 8 00:03:07.121: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.121: RADIUS: 4C 46 AA B9 A5 D5 DF EA DB E7 2B 7B 51 7E 58 3F [ LF+{Q~X?]
*Mar 8 00:03:07.121: RADIUS: State [24] 30
*Mar 8 00:03:07.121: RADIUS: 00 EF 00 B9 00 0A 00 00 EF B8 45 00 EF D2 C4 3C 81 6C 72 0E 23 FE 11 EA 12 17 50 A1 [ E
*Mar 8 00:03:07.121: RADIUS(000001C7): Received from id 1645/85
*Mar 8 00:03:07.121: RADIUS/DECODE: EAP-Message fragments, 253+53, total 306 bytes
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:07.130: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:07.130: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.130: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:07.130: EAPOL pak dump Tx
*Mar 8 00:03:07.130: EAPOL Version: 0x3 type: 0x0 length: 0x0132
*Mar 8 00:03:07.130: EAP code: 0x1 id: 0x4 length: 0x0132 type: 0xD
*Mar 8 00:03:07.130: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:07.138: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.138: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:07.138: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:07.138: EAPOL pak dump rx
*Mar 8 00:03:07.138: EAPOL Version: 0x1 type: 0x0 length: 0x05D4
*Mar 8 00:03:07.138: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 1492
*Mar 8 00:03:07.138: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:07.138: dot1x-ev(Fa0/1):
^Z
Malleswaram_2960#
*Mar 8 00:03:07.180: RADIUS: State [24] 30
*Mar 8 00:03:07.180: RADIUS: 00 EF 00 B9 00 0A 00 00 EF B8 45 00 EF D2 C4 3C 81 6C 72 0E 23 FE 11 EA 12 17 50 A1 [ E
*Mar 8 00:03:07.180: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:07.180: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:07.180: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:07.893: %SYS-5-CONFIG_I: Configured from console by jameela on vty0 (10.26.20.5)
Malleswaram_2960#
*Mar 8 00:03:10.225: RADIUS(000001C7): Request timed out
*Mar 8 00:03:10.225: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:10.225: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:13.354: RADIUS(000001C7): Request timed out
*Mar 8 00:03:13.354: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:13.354: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:16.307: RADIUS(000001C7): Request timed out
*Mar 8 00:03:16.307: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:16.307: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:19.369: RADIUS(000001C7): Request timed out
*Mar 8 00:03:19.369: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:19.369: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:22.456: RADIUS(000001C7): Request timed out
*Mar 8 00:03:22.456: RADIUS: Fail-over denied to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:22.456: RADIUS: No response from (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:22.456: RADIUS/DECODE: parse response no app start; FAIL
*Mar 8 00:03:22.456: RADIUS/DECODE: parse response; FAIL
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Received an EAP Fail
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting EAP_FAIL for 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 10(eapFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_fail
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_fail_enter called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_fail_action called
*Mar 8 00:03:22.456: dot1x_auth_bend Fa0/1: idle during state auth_bend_fail
*Mar 8 00:03:22.456: @@@ dot1x_auth_bend Fa0/1: auth_bend_fail -> auth_bend_idle
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting AUTH_FAIL on Client 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth Fa0/1: during state auth_authenticating, got event 15(authFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth Fa0/1: auth_authenticating -> auth_authc_result
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_exit called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authc_result_enter called
*Mar 8 00:03:22.456: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Sending event (2) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:22.456: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:22.456: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:22.456: dot1x-redundancy: State for client d43d.7e65.4fc1 successfully retrieved
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Received Authz fail for the client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting_AUTHZ_FAIL on Client 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth Fa0/1: during state auth_authc_result, got event 22(authzFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth Fa0/1: auth_authc_result -> auth_held
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_enter called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:22.464: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.464: EAPOL pak dump Tx
*Mar 8 00:03:22.464: EAPOL Version: 0x3 type: 0x0 length: 0x0004
*Mar 8 00:03:22.464: EAP code: 0x4 id: 0x4 length: 0x0004
*Mar 8 00:03:22.464: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting FAILOVER_RETRY on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_held, got event 21(failover_retry)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_held -> auth_restart
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_exit called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_restart_action called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting REAUTH_MAX on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_connecting, got event 11(reAuthMax)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_disconnected
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_disconnected_enter called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): d43d.7e65.4fc1:auth_disconnected_enter sending canned failure to version 1 supplicant
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:22.464: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.464: EAPOL pak dump Tx
*Mar 8 00:03:22.464: EAPOL Version: 0x3 type: 0x0 length: 0x0004
*Mar 8 00:03:22.464: EAP code: 0x4 id: 0x5 length: 0x0004
*Mar 8 00:03:22.464: dot1x-packet(Fa0/1): dot1x_auth_txCannedStatus: EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_disconnected_reAuthMax_action called
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending event (1) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:22.464: dot1x-ev:Delete auth client (0xB0000DBA) message
*Mar 8 00:03:22.464: dot1x-ev:Auth client ctx destroyed
*Mar 8 00:03:22.674: AAA/BIND(000001C8): Bind i/f
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: initial state auth_initialize has enter
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_initialize_enter called
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_initialize, got event 0(cfg_auto)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_initialize -> auth_disconnected
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_disconnected_enter called
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_restart_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has enter
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_initialize_enter called
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has idle
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: during state auth_bend_initialize, got event 16383(idle)
*Mar 8 00:03:22.674: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_idle_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Created a client entry (0x4A000DBB)
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Dot1x authentication started for 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_connecting_enter called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_restart_connecting_action called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_authenticating_enter called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_connecting_authenticating_action called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting AUTH_START for 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:22.674: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Role determination not required
Malleswaram_2960#
*Mar 8 00:03:22.674: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.674: EAPOL pak dump Tx
*Mar 8 00:03:22.674: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:22.674: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:22.674: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_idle_request_action called
*Mar 8 00:03:22.791: dot1x-ev(Fa0/1): New client notification from AuthMgr for 0x4A000DBB - d43d.7e65.4fc1
*Mar 8 00:03:22.791: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): Posting EAP_REQ for 0x4A000DBB
*Mar 8 00:03:25.761: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 7(eapReq)
*Mar 8 00:03:25.761: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_request
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_request_action called
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:25.761: dot1x-registry:registry:dot1x_ether_macaddr called
Malleswaram_2960#n
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:25.761: EAPOL pak dump Tx
*Mar 8 00:03:25.761: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:25.761: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:25.761: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (d43d.7e65.4fc1)
Malleswaram_2960#no debu
Malleswaram_2960#no debug
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): Posting EAP_REQ for 0x4A000DBB
*Mar 8 00:03:28.848: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 7(eapReq)
*Mar 8 00:03:28.848: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_request
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_request_action called
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:28.848: dot1x-registry:registry:dot1x_ether_macaddr called
Malleswaram_2960#no debug all
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:28.848: EAPOL pak dump Tx
*Mar 8 00:03:28.848: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:28.848: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:28.848: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (d43d.7e65.4fc1)
Malleswaram_2960#no debug all
All possible debugging has been turned off
Malleswaram_2960#
*Mar 8 00:03:31.180: AAA: parse name=tty1 idb type=-1 tty=-1
*Mar 8 00:03:31.180: AAA: name=tty1 flags=0x11 type=5 shelf=0 slot=0 adapter=0 port=1 channel=0
*Mar 8 00:03:31.180: AAA/MEMORY: create_user (0x21D1684) user='jameela' ruser='Malleswaram_2960' ds0=0 port='tty1' rem_addr='10.26.20.5' authen_type=ASCII service=NONE priv=15 initial_task_id='0', vrf= (id=0) key=C9A1F1D1
*Mar 8 00:03:31.389: TAC+: (-1901802859): received author response status = PASS_ADD
*Mar 8 00:03:31.389: AAA/MEMORY: free_user (0x21D1684) user='jameela' ruser='Malleswaram_2960' port='tty1' rem_addr='10.26.20.5' authen_type=ASCII service=NONE priv=15
*Mar 8 00:03:31.935: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:03:31.935: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:03:31.935: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:03:31.935: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:03:31.935: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#no deb
Malleswaram_2960#no debug al
Malleswaram_2960#no debug all
All possible debugging has been turned off
Malleswaram_2960#
*Mar 8 00:04:32.677: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:04:41.938: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:04:41.938: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:04:41.938: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:04:41.938: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:04:41.938: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:42.654: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:51.915: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:05:51.915: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:05:51.915: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:05:51.915: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:51.915: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Pls dont worry about day and time. -
Cisco 1941 Router-on-a-Stick w/ 11VLANs trunked to a Cisco 2960: From the Switch I can Ping a device in another VLAN, that device cannot ping back. Some devices can ping devices in other VLANs and the device in the other VLAN can successfully return the Ping. Have a look at the attached diagram.
Router Config:
show run
Building configuration...
Current configuration : 7224 bytes
! Last configuration change at 09:05:48 EDT Wed Aug 6 2014
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ROUTER
boot-start-marker
boot-end-marker
no aaa new-model
clock timezone EDT -8 0
ip cef
ip name-server 8.8.8.8
no ipv6 cef
multilink bundle-name authenticated
license udi pid CISCO1941/K9
object-group network Net_Obj_Group1
description This network group allows all 10.0.0.0 and Email Forwarder server through to the Plt PCs
205.191.0.0 255.255.0.0
10.0.0.0 255.0.0.0
object-group network Net_Obj_Group2
description This Network Group includes the Host IPs allowed through the Plant Router
host 10.194.28.23
host 10.194.28.25
host 10.194.28.26
host 10.194.28.27
host 10.194.28.28
host 10.194.28.29
host 10.194.28.37
host 10.194.28.39
host 10.194.28.40
host 10.194.28.70
host 10.194.28.130
host 10.194.28.131
host 10.194.28.132
host 10.194.28.133
host 10.194.28.134
host 10.194.28.135
host 10.194.28.136
host 10.194.28.137
host 10.194.28.138
host 10.194.28.139
host 10.194.28.140
host 10.194.28.141
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description Port Ge0/0 to IT Enterprise network Switch GE1/0/38
ip address 10.194.28.111 255.255.255.0
ip access-group 105 in
ip access-group 106 out
ip nat outside
ip virtual-reassembly in
shutdown
duplex full
speed auto
no mop enabled
interface GigabitEthernet0/1
description Port to Plant PCN-K/L24 Sw1 Port 0/24
no ip address
duplex auto
speed auto
no mop enabled
interface GigabitEthernet0/1.102
description Port to VLAN 102
encapsulation dot1Q 102
ip address 192.168.102.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.104
description Port to VLAN 104
encapsulation dot1Q 104
ip address 192.168.104.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.105
description Port to VLAN 105
encapsulation dot1Q 105
ip address 192.168.105.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.106
description Port to VLAN 106
encapsulation dot1Q 106
ip address 192.168.106.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.107
description Port to VLAN 107
encapsulation dot1Q 107
ip address 192.168.107.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.111
description Port to VLAN 111
encapsulation dot1Q 111
ip address 192.168.111.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.117
description Port to VLAN 117
encapsulation dot1Q 117
ip address 192.168.117.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.121
description Port to VLAN 121
encapsulation dot1Q 121
ip address 192.168.121.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.125
description Port to VLAN 125
encapsulation dot1Q 125
ip address 192.168.125.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.150
description Port to to VLAN 150
encapsulation dot1Q 150
ip address 192.168.150.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.999
description Port to VLAN 999
encapsulation dot1Q 999
ip address 192.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source static 192.168.102.201 10.194.28.23
ip nat inside source static 192.168.121.201 10.194.28.25
ip nat inside source static 192.168.106.251 10.194.28.26
ip nat inside source static 192.168.107.245 10.194.28.27
ip nat inside source static 192.168.102.251 10.194.28.28
ip nat inside source static 192.168.150.201 10.194.28.29
ip nat inside source static 192.168.107.179 10.194.28.37
ip nat inside source static 192.168.111.201 10.194.28.39
ip nat inside source static 192.168.105.201 10.194.28.40
ip nat inside source static 192.168.106.21 10.194.28.70
ip nat inside source static 192.168.107.146 10.194.28.130
ip nat inside source static 192.168.107.156 10.194.28.131
ip nat inside source static 192.168.107.161 10.194.28.132
ip nat inside source static 192.168.107.181 10.194.28.133
ip nat inside source static 192.168.107.191 10.194.28.134
ip nat inside source static 192.168.106.202 10.194.28.135
ip nat inside source static 192.168.106.212 10.194.28.136
ip nat inside source static 192.168.117.190 10.194.28.137
ip nat inside source static 192.168.117.100 10.194.28.138
ip nat inside source static 192.168.106.242 10.194.28.139
ip nat inside source static 192.168.125.100 10.194.28.140
ip nat inside source static 192.168.125.99 10.194.28.141
ip nat outside source static 10.194.28.23 10.194.28.23
ip nat outside source static 10.194.28.25 10.194.28.25
ip nat outside source static 10.194.28.26 10.194.28.26
ip nat outside source static 10.194.28.27 10.194.28.27
ip nat outside source static 10.194.28.28 10.194.28.28
ip nat outside source static 10.194.28.29 10.194.28.29
ip nat outside source static 10.194.28.37 10.194.28.37
ip nat outside source static 10.194.28.39 10.194.28.39
ip nat outside source static 10.194.28.40 10.194.28.40
ip nat outside source static 10.194.28.70 10.194.28.70
ip nat outside source static 10.194.28.130 10.194.28.130
ip nat outside source static 10.194.28.131 10.194.28.131
ip nat outside source static 10.194.28.132 10.194.28.132
ip nat outside source static 10.194.28.133 10.194.28.133
ip nat outside source static 10.194.28.134 10.194.28.134
ip nat outside source static 10.194.28.135 10.194.28.135
ip nat outside source static 10.194.28.136 10.194.28.136
ip nat outside source static 10.194.28.137 10.194.28.137
ip nat outside source static 10.194.28.138 10.194.28.138
ip nat outside source static 10.194.28.139 10.194.28.139
ip nat outside source static 10.194.28.140 10.194.28.140
ip nat outside source static 10.194.28.141 10.194.28.141
ip route 0.0.0.0 0.0.0.0 10.194.28.1
access-list 105 permit ip object-group Net_Obj_Group1 object-group Net_Obj_Group2
access-list 106 permit ip object-group Net_Obj_Group2 object-group Net_Obj_Group1
dialer-list 1 protocol ip permit
control-plane
banner login ^CC
Login banner for Plant Router #01^C
banner motd ^CC
MOTD Banner for Plant Router^C
line con 0
password XXXXXXXXX
logging synchronous
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password XXXXXXXXX
logging synchronous
login
transport input all
scheduler allocate 20000 1000
ntp server 10.199.100.92
end
Switch Config:
sh ru
Building configuration...
Current configuration : 6513 bytes
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname K24Sw01
boot-start-marker
boot-end-marker
no aaa new-model
clock timezone EDT -5
clock summer-time EDT recurring
udld aggressive
crypto pki trustpoint TP-self-signed-593746944
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-593746944
revocation-check none
rsakeypair TP-self-signed-593746944
4B58BCE9 44
quit
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
interface FastEthernet0
no ip address
interface GigabitEthernet0/1
description Trunk port for vlans 105, 111, 125 and 999 from K24Sw01 port Ge0/1 to P22Sw01 port Ge0/24
switchport trunk allowed vlan 105,111,125,999
switchport mode trunk
interface GigabitEthernet0/2
description Trunk port for vlans 150 and 999 from K24Sw01 port Ge0/2 to N25Sw01 port Ge0/26
switchport trunk allowed vlan 150,999
switchport mode trunk
interface GigabitEthernet0/3
description Trunk port for vlans 102, 104, 106, 107, 117 and 999 from K24Sw01 port Ge0/3 to K28Sw01 port Ge0/26
switchport trunk allowed vlan 102,104,106,107,117,999
switchport mode trunk
interface GigabitEthernet0/4
description Trunk port for vlans 102, 106, 107 and 999 from K24Sw01 port Ge0/4 to H23Sw01 port Ge0/26
switchport trunk allowed vlan 102,106,107,999
switchport mode trunk
interface GigabitEthernet0/5
description Trunk port for vlans 121, 125 and 999 from K24Sw01 port Ge0/5 to M21Sw01 port Ge0/24
switchport trunk allowed vlan 121,125,999
switchport mode trunk
interface GigabitEthernet0/6
description OPEN
spanning-tree portfast
interface GigabitEthernet0/7
description OPEN
spanning-tree portfast
interface GigabitEthernet0/8
description OPEN
spanning-tree portfast
interface GigabitEthernet0/9
description OPEN
spanning-tree portfast
interface GigabitEthernet0/10
description VLan 102 access port
switchport access vlan 102
spanning-tree portfast
interface GigabitEthernet0/11
description - VLan 104 access port
switchport access vlan 104
spanning-tree portfast
interface GigabitEthernet0/12
description - VLan 105 access port
switchport access vlan 105
spanning-tree portfast
interface GigabitEthernet0/13
description - VLan 106 access port
switchport access vlan 106
spanning-tree portfast
interface GigabitEthernet0/14
description - VLan 107 access port
switchport access vlan 107
spanning-tree portfast
interface GigabitEthernet0/15
description - VLan 111 access port
switchport access vlan 111
spanning-tree portfast
interface GigabitEthernet0/16
description - VLan 117 access port
switchport access vlan 117
spanning-tree portfast
interface GigabitEthernet0/17
description - VLan 121 access port
switchport access vlan 121
spanning-tree portfast
interface GigabitEthernet0/18
description - VLan 125 access port
switchport access vlan 125
spanning-tree portfast
interface GigabitEthernet0/19
description - VLan 150 access port
switchport access vlan 150
spanning-tree portfast
interface GigabitEthernet0/20
description - VLan 999 access port
switchport access vlan 999
spanning-tree portfast
interface GigabitEthernet0/21
description OPEN
spanning-tree portfast
interface GigabitEthernet0/22
description OPEN
spanning-tree portfast
interface GigabitEthernet0/23
description OPEN
spanning-tree portfast
interface GigabitEthernet0/24
description From ROUTER Gw ge0/1
switchport trunk allowed vlan 102,104-107,111,117,121,125,150,999
switchport mode trunk
interface GigabitEthernet0/25
interface GigabitEthernet0/26
interface Vlan1
no ip address
no ip route-cache
shutdown
interface Vlan102
ip address 192.168.102.253 255.255.255.0
interface Vlan104
no ip address
no ip route-cache
interface Vlan105
no ip address
no ip route-cache
interface Vlan106
no ip address
no ip route-cache
interface Vlan107
no ip address
no ip route-cache
interface Vlan111
no ip address
no ip route-cache
interface Vlan117
no ip address
no ip route-cache
interface Vlan121
no ip address
no ip route-cache
interface Vlan125
no ip address
no ip route-cache
interface Vlan150
no ip address
no ip route-cache
interface Vlan999
no ip address
no ip route-cache
ip default-gateway 192.168.102.1
ip http server
ip http secure-server
snmp-server engineID local 00000009020000019634C2C0
snmp-server community public RO
snmp-server location
snmp-server contact
banner motd ^CCC ADMIN USE ONLY! ^C
line con 0
session-timeout 10
password xxxxxx
logging synchronous
login
stopbits 1
line vty 0 4
session-timeout 10
password xxxxxxx
login
line vty 5 15
session-timeout 10
password xxxxxxxx
login
ntp server 10.199.100.92
end
K24Sw01#HI Mark,
Here is the my config:
Create sub-interfaces, set 802.1Q trunking protocol and ip address on each sub-interface
Router(config)#interface f0/0
Router(config-if)#no shutdown
(Note: The main interface f0/0 doesn’t need an IP address but it must be turned on)
Router(config)#interface f0/0.10
Router(config-subif)#encapsulation dot1q 10
Router(config-subif)#ip address 192.168.10.1 255.255.255.0
Router(config-subif)#interface f0/0.20
Router(config-subif)#encapsulation dot11 20
Router(config-subif)#ip address 192.168.20.1 255.255.255.0
(Note: In the “encapsulation dot1q 10″ command, 10 is the VLAN ID this interface operates in)
Configure VLAN
Switch(config)#vlan 10
Switch(config-vlan)#name SALES
Switch(config-vlan)#vlan 20
Switch(config-vlan)#name TECH
Set ports to access mode & assign ports to VLAN
Switch(config)#interface range fa0/1
Switch(config-if)#no shutdown
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 15
Switch(config-if)#interface range fa0/3
Switch(config-if)#no shutdown
Switch(config-if)#switchport mode access
Switch(config-if)# switchport access vlan 20
Switch(config-if)#interface range fa0/5
Switch(config-if)#no shutdown
Switch(config-if)#switchport mode trunk
1. Please check all your port are up.
2. Check the config once again.
3. Make sure the swicth and router connection port configured as trunk and it should be up.
This config is working for me,
Regards
Dont forget to rate helpful posts. -
Nexus 2K to Cisco 2960 IOS Switch
Hi,
I am trying to connect Nexus 2K FEX to Cisco 2960 IOS Switch (Trunk config) and causing spanning tree loop having issues. I am aware that I should't be connecting non host port to 2K FEX but it's corner case. I have done similar setup with Access Port configuration and didn't faced any issues.
Nexus 5K config Config
interface Ethernet107/1/47
switchport mode trunk
switchport trunk allowed vlan 500-501
spanning-tree guard root
spanning-tree bpdufilter enable
interface Ethernet108/1/47
switchport mode trunk
switchport trunk allowed vlan 500-501
spanning-tree guard root
spanning-tree bpdufilter enable
2960-Config
interface GigabitEthernet1/0/47
switchport mode trunk
switchport trunk allowed vlan 500-501
spanning-tree bpdufilter enable
interface GigabitEthernet1/0/48
switchport mode trunk
switchport trunk allowed vlan 500-501
spanning-tree bpdufilter enable
Error Log
%FWM-2-STM_LOOP_DETECT: Loops detected in the network for mac 001b.1700.0130 among ports Eth107/1/47
Eth108/1/47 vlan 500 - Disabling dynamic learn notifications for 180 seconds
Should I configure port as "spanning-tree port type network" and create VPC and "storm-control broadcast level" to stop future occurrence? OR Do i have to configure anything else to prevent spanning-tree loops?
Thanks for your help
RiteshHi,
spanning-tree port type network is used for VPC peer-link. Try creating a new VPC and add ports 107/1/47 and 108/1/47 to it and a Portchannel on the 2960 and test.
HTH -
Power up cisco 2960 switch with 12V DC Power
hi all ,
I have some issue with supply power to cisco 2960-24TT-L switch. In my server farm rack is having DC current of -48V. But however cisco switch require 12V DC current.
Cisco Spec.
Cisco Catalyst 2960-24TT-L
12V at 5 A
5 A
How can I power on the switch using DC current ? Is there any power converter which I can purchase ? your responses are very much.
ThanksYou may also go here:
https://supportforums.cisco.com/community/netpro/small-business
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router -
hi
On a Cisco 2960S-48TS-L, After a Mac flapping the CPU went to 100 %
700sw10_emb#sh proc cpu sort
CPU utilization for five seconds: 99%/5%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
155 37771767 3603617 10481 23.51% 23.68% 23.53% 0 Hulc LED Proces
s
225 4213295 956535 4404 23.31% 23.01% 22.98% 0 HULC DAI Proces
s
234 3486099 1061257 3284 20.21% 20.41% 20.48% 0 IP Host Track P
r
182 3761068 742168 5067 18.51% 18.40% 18.46% 0 Auth Manager
104 244786 3413567 71 1.80% 1.57% 1.51% 0 HLFM address le
here is the log
Mar 13 17:43:38.076: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe
rnet1/0/29, changed state to up
Mar 14 08:05:25.076: %SW_MATM-4-MACFLAP_NOTIF: Host 000b.6b22.7b72 in vlan 1 is
flapping between port Gi1/0/48 and port Gi1/0/51
Mar 14 08:07:52.602: %SW_MATM-4-MACFLAP_NOTIF: Host 000b.6b22.7b72 in vlan 1 is
flapping between port Gi1/0/48 and port Gi1/0/51
Mar 14 08:09:16.681: %SW_MATM-4-MACFLAP_NOTIF: Host 000b.6b22.7b72 in vlan 1 is
flapping between port Gi1/0/48 and port Gi1/0/51
.Mar 14 08:38:10.808: %SW_MATM-4-MACFLAP_NOTIF: Host 000b.6b22.79de in vlan 1 is
flapping between port Gi1/0/48 and port Gi1/0/51
The only solution is restart the switch
regardsI am not sure what IOS version you are using but here's my recommendation:
1. If you are running 12.2 then use 12.2(55)SE8; or
2. If you are running 15.X then use 15.0(2)SE4.
Don't even bother using the others. -
Gigabitethernet negotiation problem with cisco 2960
Hi
I have 2 cisco 2960 switches. one is a WS-C2960-48TT-L Version 12.2(25r)SEE1 and the other WS-C2960-48TC-L Version 12.2(25r)FX.
When i build a trunk between the gigabit ethernet ports, WS-C2960-48TC-L end shows me half duplex with autonegotiation whereas it is hard coded on the WS-C2960-48TT-L.
Iam not able to set the speed and duplex for the port on the 2nd switch.
Is this a bug with the 2960 or a compatibility feature between the 2 2960's
NarayanHello Narayan,
Has the speed and dubplex settings on the 2960 been configured? In that case auto-negotiation frames are not sent and the switchport cannot determine the speed/duplex from it's link partner. It will automatically choose 1000 half-duplex.
Refer to the following document: http://www.cisco.com/warp/public/473/3.html
HTH
--Leon
* Please rate posts. -
Recovery missing or corrupted IOS of Cisco 2960 Catalyst Switch
Dear Team,
I have Cisco 2960 48P switch, It is keep getting restarted and config was erased.
when I tried to run the IOS from hypertrm in room mode, I am getting below error..
My doubt is, is there any issue with hardware & what is the cause of for below error
suggest me, is there any option to upgrade the IOS?
switch: flash_init
Initializing Flash...
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 32513024
flashfs[0]: flashfs fsck took 9 seconds.
...done Initializing Flash.
switch: copy xmodem: flash:c2960-lanbasek9-mz.122-50.SE5.bin
Begin the Xmodem or Xmodem-1K transfer now...
CCCCBB0BB0................flashfs[0]: filesystem marked down. Use "fsck" to rec
over.
flash:c2960-lanbasek9-mz.122-50.SE5.bin: interrupted system call
switch:Error message means your BIN file is corrupt. You need to download again from the Cisco website.
-
Change default username on Cisco 2960
Hi! It is possible to change de default username "admin" from Cisco 2960?
Ports Model SW Version SW Image
WS-C2960-24TC-L 12.2(35)SE5 C2960-LANBASEK9-MHello,
If you have console access, please try the following:
configure terminal
##### Create a new username/password pair ############
username priv 15 password
##### Configure HTTP access using local username ######
ip http authentication local
##### Configure telnet access using local username #####
line vty 0 4
login local
exit
If you want to delete a username, please use the following command:
no username
Hope this helps.
Regards,
NT -
As clear memory dead Switch cisco 2960
Hello All !!
As Clear memory dead process I/O Switch cisco 2960 ?I do not speak English perfectly, I'll try to summarize
Switch this process my memory I / 0 Very High, restart several times, but the process does not diminish.
thank you. -
hi all,
can a cisco 2960s connect to asa with multiple vlans and still route to DMZ and internet?
thanks for any comment you may add.Hi,
I have pretty much lost the track on the Cisco Switch and Router products but to my understanding all the 2900 series Switches are usually just L2 devices which dont usually handle routing. But as I said I dont know if there has been some changes regarding their abilities. To my understanding its always been the 3000 Series switches that handle L3 operation also.
I am also not sure if I understood your question correctly.
You can naturally trunk your 2960 Vlans to the ASA and let it handle the routing.
But as I said I dont quite know if I understood what you are after. Maybe you would want to expand on your question a bit more?
- Jouni -
I have load CISCO-ENVMON-MIB and initiate walk in it but unable to find OID of Cisco 2960 temperature monitor..
I have search over net and found .1.3.6.1.4.1.9.9.13.1.3.1.3.1 for temperature but this OID is not responding in this mib.
Regards,
Arshad AhmedHi,
What is the version of IOS you are using? What is your SNMP config?
Here is an example output:
snmpwalk -v2c -c public 10.12.12.12 .1.3.6.1.4.1.9.9.13
SNMPv2-SMI::enterprises.9.9.13.1.3.1.2.1 = STRING: "chassis"
SNMPv2-SMI::enterprises.9.9.13.1.3.1.6.1 = INTEGER: 5
SNMPv2-SMI::enterprises.9.9.13.1.4.1.2.1 = STRING: "chassis"
SNMPv2-SMI::enterprises.9.9.13.1.4.1.3.1 = INTEGER: 1
SNMPv2-SMI::enterprises.9.9.13.1.5.1.2.1 = STRING: "internal power supply"
SNMPv2-SMI::enterprises.9.9.13.1.5.1.3.1 = INTEGER: 1
SNMPv2-SMI::enterprises.9.9.13.1.5.1.4.1 = INTEGER: 0
SNMPv2-SMI::enterprises.9.9.13.1.6.0 = Hex-STRING: 00
SNMPv2-SMI::enterprises.9.9.13.2.1.0 = INTEGER: 2
SNMPv2-SMI::enterprises.9.9.13.2.3.0 = INTEGER: 2
SNMPv2-SMI::enterprises.9.9.13.2.4.0 = INTEGER: 2
SNMPv2-SMI::enterprises.9.9.13.2.5.0 = INTEGER: 2
SNMPv2-SMI::enterprises.9.9.13.2.6.0 = INTEGER: 2
To verify that the MIB exists in your image please navigate to:
http://tools.cisco.com/Support/SNMP/do/MIBSupport.do?local=en&step=3
Once there, issue a 'sh ver' on your device and copy and paste the entire name into the tool.
Thanks -
Cisco 2960-X stacking question
Hi all,
We're planning buy 6 set of Cisco 2960-X with stacking with existing two firewall with HA function (please see attached diagram), if firewall 01 down will auto failover to firewall 02, is this network design good ?
Please some expert give us suggestion.
Thanks1. Do 2960-X support 6 member stacking ?
2960X support a stack size of 8, however, you need to be careful. The stacking speed of the 2960X is 20 Gbps. So you need to know if stacking up 8 is beneficial or not.
2. Do 2960-X support Bladeswitch stack cable ?
No. The stacking cable for the 2960S/X/XR are specific only for this models.
3. I think need buy stack module, right ?
Stacking modules and stacking cables.
Maybe you are looking for
-
I can't log into my mobile me account from my lap top. Is it because of my operating system? I'm on Mac OS X 10.6.8? Every time I try to enter my data in on the control panel I get an error that says; "Your MobileMe member name or password may be i
-
Hi All, While saving my business card as a pdf, black seems to go grey, and Im not sure the cause of it. I don't know whether it's simply some settings in indesign. I suspect though because I have placed images from photoshop, the contrast of grey ag
-
Using summation function in xslt transformation
Hi, I'm new to SOA and i'm just exploring the functions in SOA suite. I couldn't add more than one parameter in summation function. summation function takes only one parameter as input I hope. How to use it. Thanks and Regards Karthick
-
Question on weblogic that is part of BPM suite.
Hi Team, I have a requirement to work on ADF application, BPM process Since BPM suite comes with weblogic server, Can i use it for deploying ADF applications also. or do i need a separate SOA suite for deploying ADF applications Thanks Parker.
-
Hi, I'm new to Oracle APPS. As part of a TAR , I've to do the step below but I need help in this.Its very urgent . Thanks a lot. On a unix session, open PYUPIP on 'PEUTRC' as - PYUPIP <username>/<password>@<dbname> 'PEUTRC' > trace_file.log Thanks...