Cisco 2960-s stack problem

hi all,
i try to counfigure 2X 2960-S as stack , one is 48 ports and the other is 24 ports.
i configured the command switch 1 priority 14 and the renumber command.
when the switches is restarted the 48 port sw is the master and this is ok.
when i take the master down, the 24 ports SW is take the master , but when the master (48) is back to live , he is boot as member.
how can i force the 48 take the master again?
thanks!

Hello.
After a new stack master is elected and the previous stack master becomes available, the previous stack master does not resume its role as stack master.
Per documentation:
A stack master retains its role unless one of these events occurs:
The switch stack is reset.*
The stack master is removed from the switch stack.
The stack master is reset or powered off.
The stack master fails.
The switch stack membership is increased by adding powered-on standalone switches or switch stacks.*
In the events marked by an asterisk (*), the current stack master might be reelected based on the listed factors.
PS: could you clarify why do you have the requirement?

Similar Messages

  • Cisco 2960-X stacking question

    Hi all,
    We're planning buy 6 set of Cisco 2960-X with stacking with existing two firewall with HA function (please see attached diagram), if firewall 01 down will auto failover to firewall 02, is this network design good ?
    Please some expert give us suggestion.
    Thanks 

    1. Do 2960-X support 6 member stacking ?
    2960X support a stack size of 8, however, you need to be careful.  The stacking speed of the 2960X is 20 Gbps.  So you need to know if stacking up 8 is beneficial or not. 
    2. Do 2960-X support Bladeswitch stack cable ?
    No.  The stacking cable for the 2960S/X/XR are specific only for this models.  
    3. I think need buy stack module, right ?
    Stacking modules and stacking cables.

  • 2960s stack problem

    I have a problem with 4 cisco 2960-s Switches in a stack.
    2 of the switches are 2960-48fps-l
    1 is a 2960-f48fps-l
    and 1 is a 2960-24pd-l
    The problem I ran into is the 2960-f48fps-L was running version 15 out of the box so I got a version mismatch when I did a show switch. So i upgraded all 4 switches to the newest ios 15.0.2 when they rebooted now 2 of them say provision and the f48fps does not even show. I have tried everything from moving the cables around to wiping the config on all 4 switch to setting provision setting to setting priority. If I go back to the original version 12.2 on the other 3 switch they all work fine but the oldest version on the f48fps is 15. I have tried everything all with no luck can anyone help?

    Hi,
    Can you make sure that all of the switches use the same SDM template? You can check that with the show sdm prefer command.
    Hope this helps.

  • Catalyst 2960 Plus Series SI stack problems with a SMC8024L2

    Hi,
    I am trying to stack a SMC8024L2 with CISCO 2960. Reading forum topics seems that additional commands are needed for the CISCO... Would someone know what needs to be performed?
    Actual symptoms are that SMC looses its IP after several minutes connected. Once that is reseted to fabric values and reprogrammed, it works fine for several minutes, but suddenly is not reachable by web, AND it is not foundable by Nettools.
    Configuration:
    CISCOROUTER/SONICWALL/CISCOSWITCH-SMCSWITCH
    Thanks in advance...!

    Well it probably wouldn't be confusing if I could find a clear set of ground rules.  The documentation mentions "FlexStack protocol", but the discussions seem to indicate that this is a control plane protocol. Do the stacking modules operate as ethernet bridges when making forwarding decisions like any other switch port?  If the answer is yes then at least I understand the principal of operation.  But now if you throw multi-chassis etherchannel uplinks into the mix divining general layer 2 paths becomes a little murky.
    Although now that I look at it, using this cabling has an advantage over a straight ring topology.  Once a frame hits the stack it is never more than 2 hops away from it's destination.  With daisy-chained switches it could be up to 4 hops.  This is of course assuming standard 802.1d-like forwarding.  This may be an invalid assumption.  I don't see any way to get spanning tree info for the stack ports.
    (EDIT:  standard ring topology would also have a maximum of 2 hops to any switch, not 4)

  • Gigabitethernet negotiation problem with cisco 2960

    Hi
    I have 2 cisco 2960 switches. one is a WS-C2960-48TT-L Version 12.2(25r)SEE1 and the other WS-C2960-48TC-L Version 12.2(25r)FX.
    When i build a trunk between the gigabit ethernet ports, WS-C2960-48TC-L end shows me half duplex with autonegotiation whereas it is hard coded on the WS-C2960-48TT-L.
    Iam not able to set the speed and duplex for the port on the 2nd switch.
    Is this a bug with the 2960 or a compatibility feature between the 2 2960's
    Narayan

    Hello Narayan,
    Has the speed and dubplex settings on the 2960 been configured? In that case auto-negotiation frames are not sent and the switchport cannot determine the speed/duplex from it's link partner. It will automatically choose 1000 half-duplex.
    Refer to the following document: http://www.cisco.com/warp/public/473/3.html
    HTH
    --Leon
    * Please rate posts.

  • 4500-x vss MEC to 2960-x stack

                      Building A
    (2) 4500-x VSS
    (9) closets with 2960-x stacks
    (2) Data Center N5K-C5596t
    I'm having a difficult time trying to find documentation.
    I have the (2) 4500-x configured with VSS and am trying to find info on connecting the 2960-x stacks.

    Hi,
    some info.
    PAgP is supported in all platforms except the Cisco Catalyst 37xx stack configuration in which cross-stack EtherChannel (LACP) is required to have MEC-connectivity with the VSS. Because cross-stack EtherChannel does not support PAgP, it cannot use enhanced PAgP for dual-active detection. A common approach to resolve this gap in support is to use two EtherChannel links from the same stack member. This solution is a non-optimal design choice because it creates a single point-of-failure. If a stack member containing that EtherChannel fails, the whole connectivity from the stack fails. To resolve this single point-of-failure problem, you can put two dual-link EtherChannel group, each on separate stack member connected to VSS; however, it will create a looped topology. The loop-free topology requires a single EtherChannel bundle to be diversified over multiple members which in turn requires LACP.

  • How to connet cisco 2960S switch to sony nexus 7?

    I want to buy an cisco WS-C2960S-24TS-S switch to help me solve business networking problem. Can someone help me to connect cisco 2960s switch to nexus 7 ?

    I don't need to do anything config on the new switch, I just need to upgrade the new switch's IOS version as the existing stack.
    Correct.  Upgrade using the command "archive download-sw" instead copying the BIN files.  
    After doing above task, I connect all stack cable and power cord as you said, and then the new switch can be synchronized with the MASTER switch. right??
    Correct.  The new switch should NOT have any configuration.  This includes VLAN.dat file.

  • Cisco 2960-X & ISE accounting- username Radius attribute missing

    Hi,
    I'm facing an issue with cisco 2960 switch radius accounting with Cisco ISE1.2.1 .here is my senario:
    - Username (vendor1) is configured in ISE local database, under  group (VENDOR)
    - Authentication protocol : wired  MAB 
    - Authentication method : webauth  using guest portal  , the user is a  vendor  , so no dot1x configured on his NIC .
    the problem is that , the switch is not sending the username as a part of radius attribute , in the authentication log , the username shown as the MAC address of the user machine , therefor , I can not configure my authorization condition using  internaluser:Name  Equal  vendor1
    while if  I configure the condition using the identity group condition  IdentityGroup:Name  Equal  VENDOR  , it works .
    The same configuration is working on 3750 switch  with no issue .
    Here is my Switch config:
    aaa authentication login default local
    aaa authentication dot1x default group radius
    aaa authorization network default group radius 
    aaa authorization auth-proxy default group radius 
    aaa accounting auth-proxy default start-stop group radius
    aaa accounting dot1x default start-stop group radius
    aaa accounting update periodic 5
    username admin password 
    username radius-test password 
    aaa server radius dynamic-author
     client 172.16.2.20 server-key 7 04490A0206345F450C00
     client 172.16.2.21 server-key 7 03165A0F0F1A32474B10
    radius server ISE-RADIUS-1
     address ipv4 172.16.2.20 auth-port 1812 acct-port 1813
     automate-tester username radius-test idle-time 15
     key 7 111B18011E0718070133
    radius server ISE-RADIUS-2
     address ipv4 172.16.2.21 auth-port 1812 acct-port 1813
     automate-tester username radius-test idle-time 15
     key 7 0214055F02131C2A4957
    radius-server attribute 6 on-for-login-auth
    radius-server attribute 8 include-in-access-req
    radius-server attribute 25 access-request include
    radius-server attribute 31 mac format ietf upper-case
    radius-server attribute 31 send nas-port-detail
    radius-server dead-criteria time 5 tries 3
    radius-server vsa send accounting
    radius-server vsa send authentication
    any help  !!!

    Thanks for your reply , I know what's MAB , if you read my explanation again , i mentioned that the user is authenticated in the guest portal which mean that I have web authentication , and it is working fine .. The only issue is that I can not use the vendor1 username as part of authorization condition and this is because the switch is not sending the radius attribute type 1 to the ISE , thus , on the ise authentication log the MAC address  of the client machine is shown as a username not the actual username ( vendor1) 
    as I mentioned also , I have exactly the same setup with ise 1.2 and 3750 switch and I do not have this issue .I experience this with 2960x only . 

  • Adding 2960-X to 2960-S Stack

    i purchased a new 2960-X switch
    i  would like to add it to an existing 2 switch 2960-s stack
    i understand i need to downgrade the stack speed on the 2960-x with :
    switch stack port-speed 10
    do the IOS version need to be identical on all switches?
    i have:
    2960-s = 12.2(55)SE3
    2960-x =  15.0(2)EX3
    if they do need to be identical, whats the best way to do this?
    thanks

    Yes, use this command with a .tar file to upgrade all switches in the stack.
    Here is an example of using the `archive download-sw` command to upgrade a stack of Cisco Catalyst 2960-S switches. Notice that the number of members in the stack is not relevant to this command. By default all members are upgraded unless the network admin uses the options to do otherwise. The TFTP IP address is 192.168.1.1, and the tar file name is c2960s-universalk9-tar.122.53.SE.tar
    Switch# archive download-sw tftp://192.168.1.1/c2960s-universalk9-tar.122.53.SE.tar
    http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps6406/white_paper_c11-578928.html
    HTH

  • Cisco 2960 / Linksys SRW2008P - Radius dynamic vlan authentication

    Hi all,
    I am planning on purchasing a Linksys SRW2008P before I buy it I want to know if it has these features.
    This is how my test lab is setup.
    Laptop -> Linksys SRW2008 -> Cisco 2960 -> Linksys WRVS4400N -> Internet
    My Cisco 2960 is going act as the "Distribution Switch" in my Lab. It's main purpose is to implment Radius 802.1X dynamic VLAN(s)
    The Linksys WRV2008 will act as an "Access Switch" the main features I would like to know is if it can support 802.1X dynamic VLAN(s) propagated from the Linksys 2960.
    For exmple: I am going to setup all my VLAN's on the 2960 and I want them to replicate to my SRW 2008 (like VTP). Whoever plugs into a port on the SRW will be authenticated via RADIUS and RADIUS will authenticate the port and send the VLAN information.
    I searched throughout the forms and from what I see is that Linksys switches do not support Dynamic VLAN(s) but I want to double check
    The reason why I am doing this is because I want 802.1X authentication throughout my small office but the problem is some offices have 1 Port with 2 users and a printer. I want both users to authenticate via 802.1X and avoid trying to buy a 2960 8 port switch for 500$ just for 2 users.
    If anybody has any suggestions or past experiences with a situation similiar to mine that would be great!
    Cheers

    HI.  I have read a previous post that can confirm if Linksys switches support dynamic vlans.  Check out the link below.
    http://forums.linksys.com/linksys/board/message?board.id=Switches&message.id=4511

  • Native VLAN on Cisco 3750x vs Cisco 2960S

    Hi,
    I have a scenario where I connect my Cisco switch 2960s with Cisco router 1941 as photo below
    My question is when i connect router with cisco 2960s I config interface Gi1/0/1 as a trunk. everything work fine, I can ping from router to switch(172.16.29.2).
    But when I changed to cisco 3750x, i config interface Gi1/0/1 as a trunk, it cannot ping from router to switch(172.16.29.2). But after I add native vlan 30 on interface Gi1/0/1 I can ping from router to switch (172.16.29.2)
    Any idea why ? is there any different of native vlan on cisco 2960s and 3750x ?
    Thank you for your kind answer
    John

    Hi John
    It seems for me that the 3750 is doing what it should do, if the router do not have subinterfaces and dot1q, it will send traffic without dot1q tag, and the 3750 will drop these packets because they arrive without a tag. That's why native vlan fixes the problem.
    The 2960 should work the same way that 3750 do, so I wonder if there is some differences in the config between the switches.
    Can You share the config for gi0/1 on the router and also the switchportconfig for both switches.
    Also a "show interface gi1/0/1 switchport" for both switches.
    /Mikael

  • Cisco 2960s Switch replacement

    Greetings,
    Dear Experts,
    We are using the Cisco 2960s Switches in our network. We have two failed switches and asked for replacement from our supplier. They informed that the 2960s model is approaching End Of Service (EOS) and the replacement of that model are as below:
    1- WS-C2960X-24TS-L
    Catalyst 2960-X 24 GigE, 4 x 1G SFP, LAN Base
    2-WS-C2960S-24TS-L
    Catalyst 2960S 24 GigE, 4 x SFP LAN Base
    What is the best practice to make my decision of which to select? will it make difference from the configuration perspective? is there a possibility for conflict with the existing 2960s Switches?
    Many thanks in advance for your kind assistance.
    Thanks and Regards

    We have two failed switches and asked for replacement from our supplier.
    Time for you to talk to your supplier.  Cisco has announced the EoS/EoL for the 2960S back in November 2014 (End-of-Sale and End-of-Life Announcement for the Cisco Catalyst 2960-S Series and 2960-SF Series Switches).  However, this only means the date of November 2014 is just a date of announcement.  The final date of sale for the 2960S is November 2015. 
    I think your supplier either is getting confused (didn't read the announcement properly or didn't know) or is just looking for ways to make more money.  
    is there a possibility for conflict with the existing 2960s Switches?
    You can form a stack of 2960S and 2960X.  Just know the limitations, and they are: 
    1.  The entire stack must have the same IOS versions; 
    2.  The stack speed will drop from 20 Gbps (2960X) to 10 Gbps because 2960S has been set to run only at this speed; and
    3.  You cannot have five or more in a stack if you have a 2960S as a member of the stack.

  • Printer Reboots at 75% when connected to Cisco 2960

    Currently Being Moderated
    Xerox 5745 Printer Reboots at 75% when connected to Cisco 2960
    Hi,
    We are having a problem with our Xerox 5745 multifunction Printer...
    This problem had been forwarded to Xerox, but they claim that a problem was caused by a power surge on our Cisco router.
    We are having a total of 8 CiscoCatalyst 2960 Series in our IT Communication rooms.
    We are also having 2 Xerox 7120, 4 Xerox 5745, 6 HP5200 and 300 computers - PC (HP Desktop) and Laptop (Samsung).
    Network : all connected to CISCO Catalyst 2960 Series
    Printer Setup:
    IP Address: Manual IP Assignment (DHCP Disabled)
    PC Setup: TCP/IP –RAW on Port 9100 – SNMP Status ENABLED
    The two machines has same firmware software and configuration settings.
    one machine just been installed with latest firmware
    Problem:
    On 3 Xerox 5745 display panel shows: "Network Controller booting"
    at 75% the system restart and go on again and again.
    This happens when cables are connected to CISCO Catalyst 2660.
    Testing done:
    •1. No problem, Connecting directly to laptop using (crossover cable), accesss to printing is normal.
    •2. No Problem, Using other switch - dLink (not CISCO Catalyst 2960), the printing is normal.
    •3. Not work, changing ip address; disabling all protocol; changing speed to 10MBps.
    •4. Not work, Switching to other port on CISCO Catalyst 2960.
    •5. Not work, Re-starting the Cisco Catalyst 2960 s.
    •6. Not work, Changing cables.
    HELP! Please ...

    Ferdinand,
    at least you're not the only one who's experiencing this problem:
    http://forum.support.xerox.com/t5/Hardware/Workcentre-5135-network-controller/td-p/5086
    http://www.fixya.com/support/t556616-network_controller_unavailable (read the comments too!)
    In case of your c2960 supports PoE, did you test to disable power inline (I know, PoE normally can't be the reason - but this is a really strange problem)?
    What happens when you boot a printer without network connectivity (or with the dLink) to 100% and connect it after that to the c2960 switch?

  • How to Recover Password on Cisco 2960 Switch?

    How to Recover Password on Cisco 2960 Switch? Who knows, please tell me the detail steps, thank you very much!

    You can find the detail steps on this article, hope can solve your problem.
    http://www.briefingwire.com/pr/how-to-recover-password-on-cisco-2960-switch
    and as I research, the WS-C2960X-48TS-L on sale on 3anetwork.com now, get a quote for the big discount.
    WS-C2960X-48TS-L
    http://www.3anetwork.com/cisco-ws-c2960x-48ts-l-price_p1542.html

  • IEEE 802.1x with EAP-TLS issue in cisco 2960

    In My Cisco 2960 switch is not working with EAP-TLS mechanism of 802.1x but its works well with other  protocols like EAP-PEAP or MAC Address authentication.
    Below is the configuration
    aaa authentication login default group tacacs+ local
    aaa authentication enable default group tacacs+ enable
    aaa authentication dot1x default group radius
    aaa authorization commands 15 default group tacacs+ local
    aaa authorization network default group radius
    aaa authorization configuration default group radius
    aaa accounting update periodic 30
    aaa accounting dot1x default start-stop group radius
    aaa accounting exec default start-stop group tacacs+
    aaa accounting commands 0 default start-stop group tacacs+
    aaa accounting commands 15 default start-stop group tacacs+
    aaa accounting network default start-stop group tacacs+
    aaa accounting connection default start-stop group tacacs+
    aaa accounting system default start-stop group tacacs+
    interface FastEthernet0/1
    switchport access vlan 11
    switchport mode access
    speed 100
    duplex full
    authentication order dot1x mab webauth
    authentication port-control auto
    mab
    dot1x pae authenticator
    dot1x timeout tx-period 3
    dot1x timeout supp-timeout 3
    spanning-tree portfast
    spanning-tree bpduguard enable
    Can anyone suggest me ?

    Thanks for the reply jatin.
    I have a client on the interface fa0/1 with a valid client certificate. And have a debug logs as below
    *Mar  8 00:03:06.266: dot1x-ev(Fa0/1): Interface state changed to UP
    *Mar  8 00:03:06.266: AAA/BIND(000001C7): Bind i/f 
    *Mar  8 00:03:06.266:     dot1x_auth Fa0/1: initial state auth_initialize has enter
    *Mar  8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_initialize_enter called
    *Mar  8 00:03:06.266:     dot1x_auth Fa0/1: during state auth_initialize, got event 0(cfg_auto)
    *Mar  8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_initialize -> auth_disconnected
    *Mar  8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_disconnected_enter called
    *Mar  8 00:03:06.266:     dot1x_auth Fa0/1: idle during state auth_disconnected
    *Mar  8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
    *Mar  8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
    *Mar  8 00:03:06.266: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (0000.0000.0000)
    *Mar  8 00:03:06.266:     dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has enter
    *Mar  8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_initialize_enter called
    *Mar  8 00:03:06.266:     dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has idle
    *Mar  8 00:03:06.266:     dot1x_auth_bend Fa0/1: during state auth_bend_initialize, got event 16383(idle)
    *Mar  8 00:03:06.266: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
    *Mar  8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
    *Mar  8 00:03:06.266: dot1x-ev(Fa0/1): Created a client entry (0xB0000DBA)
    *Mar  8 00:03:06.266: dot1x-ev(Fa0/1): Dot1x authentication started for 0xB0000DBA (0000.0000.0000)
    *Mar  8 00:03:06.266: dot1x-ev:DOT1X Supplicant not enabled on FastEthernet0/1
    *Mar  8 00:03:06.266: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
    *Mar  8 00:03:06.266:     dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
    *Mar  8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
    *Mar  8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
    *Mar  8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
    *Mar  8 00:03:06.274: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0xB0000DBA
    *Mar  8 00:03:06.274:     dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
    *Mar  8 00:03:06.274: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
    *Mar  8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_enter called
    *Mar  8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_authenticating_action called
    *Mar  8 00:03:06.274: dot1x-sm(Fa0/1): Posting AUTH_START for 0xB0000DBA
    *Mar  8 00:03:06.274:     dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
    *Mar  8 00:03:06.274: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
    *Mar  8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
    *Mar  8 00:03:06.274: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:06.274: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:06.274: dot1x-registry:registry:dot1x_ether_macaddr called
    *Mar  8 00:03:06.274: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:06.274: EAPOL pak dump Tx
    *Mar  8 00:03:06.274: EAPOL Version: 0x3  type: 0x0  length: 0x0005
    *Mar  8 00:03:06.274: EAP code: 0x1  id: 0x1  length: 0x0005 type: 0x1
    *Mar  8 00:03:06.274: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (0000.0000.0000)
    *Mar  8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_request_action called
    *Mar  8 00:03:06.794: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:06.794: dot1x-packet(Fa0/1): queuing an EAPOL pkt on Auth Q
    *Mar  8 00:03:06.794: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
    *Mar  8 00:03:06.794: EAPOL pak dump rx
    *Mar  8 00:03:06.794: EAPOL Version: 0x1  type: 0x1  length: 0x0000
    *Mar  8 00:03:06.794: dot1x-ev:
    dot1x_auth_queue_event: Int Fa0/1 CODE= 0,TYPE= 0,LEN= 0
    *Mar  8 00:03:06.794: dot1x-packet(Fa0/1): Received an EAPOL frame
    *Mar  8 00:03:06.794: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
        pae-ether-type = 888e.0101.0000
    *Mar  8 00:03:06.794: dot1x-ev(Fa0/1): Couldn't find the supplicant in the list
    *Mar  8 00:03:06.794: dot1x-ev(Fa0/1): New client detected, notifying AuthMgr
    *Mar  8 00:03:06.794: dot1x-ev(Fa0/1): Sending event (0) to Auth Mgr for d43d.7e65.4fc1
    *Mar  8 00:03:06.794: dot1x-packet(Fa0/1): Received an EAPOL-Start packet
    *Mar  8 00:03:06.794: EAPOL pak dump rx
    *Mar  8 00:03:06.794: EAPOL Version: 0x1  type: 0x1  length: 0x0000
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): Posting EAPOL_START on Client 0xB0000DBA
    *Mar  8 00:03:06.794:     dot1x_auth Fa0/1: during state auth_authenticating, got event 4(eapolStart)
    *Mar  8 00:03:06.794: @@@ dot1x_auth Fa0/1: auth_authenticating -> auth_aborting
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_exit called
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_enter called
    *Mar  8 00:03:06.794: dot1x-ev(Fa0/1): 802.1x method gets the go ahead from Auth Mgr for 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:06.794: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): Posting AUTH_ABORT for 0xB0000DBA
    *Mar  8 00:03:06.794:     dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 1(authAbort)
    *Mar  8 00:03:06.794: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_initialize
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_initialize_enter called
    *Mar  8 00:03:06.794:     dot1x_auth_bend Fa0/1: idle during state auth_bend_initialize
    *Mar  8 00:03:06.794: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): Posting !AUTH_ABORT on Client 0xB0000DBA
    *Mar  8 00:03:06.794:     dot1x_auth Fa0/1: during state auth_aborting, got event 20(no_eapolLogoff_no_authAbort)
    *Mar  8 00:03:06.794: @@@ dot1x_auth Fa0/1: auth_aborting -> auth_restart
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_exit called
    *Mar  8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
    *Mar  8 00:03:06.794: dot1x-ev(Fa0/1): Resetting the client 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:06.794: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_restart_action called
    *Mar  8 00:03:06.802: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
    *Mar  8 00:03:06.802:     dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
    *Mar  8 00:03:06.802: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
    *Mar  8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
    *Mar  8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0xB0000DBA
    *Mar  8 00:03:06.811:     dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
    *Mar  8 00:03:06.811: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_enter called
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_authenticating_action called
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): Posting AUTH_START for 0xB0000DBA
    *Mar  8 00:03:06.811:     dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
    *Mar  8 00:03:06.811: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
    *Mar  8 00:03:06.811: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:06.811: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:06.811: dot1x-registry:registry:dot1x_ether_macaddr called
    *Mar  8 00:03:06.811: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:06.811: EAPOL pak dump Tx
    *Mar  8 00:03:06.811: EAPOL Version: 0x3  type: 0x0  length: 0x0005
    *Mar  8 00:03:06.811: EAP code: 0x1  id: 0x1  length: 0x0005 type: 0x1
    *Mar  8 00:03:06.811: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_request_action called
    *Mar  8 00:03:06.811: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:06.811: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
    *Mar  8 00:03:06.811: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
    *Mar  8 00:03:06.811: EAPOL pak dump rx
    *Mar  8 00:03:06.811: EAPOL Version: 0x1  type: 0x0  length: 0x0022
    *Mar  8 00:03:06.811: dot1x-ev:
    dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 1,LEN= 34
    *Mar  8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAPOL frame
    *Mar  8 00:03:06.811: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
        pae-ether-type = 888e.0100.0022
    *Mar  8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAP packet
    *Mar  8 00:03:06.811: EAPOL pak dump rx
    *Mar  8 00:03:06.811: EAPOL Version: 0x1  type: 0x0  length: 0x0022
    *Mar  8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
    *Mar  8 00:03:06.811:     dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
    *Mar  8 00:03:06.811: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
    *Mar  8 00:03:06.811: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
    *Mar  8 00:03:06.811: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
    *Mar  8 00:03:06.819: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
    *Mar  8 00:03:06.819: RADIUS(000001C7): Config NAS IP: 0.0.0.0
    *Mar  8 00:03:06.819: RADIUS/ENCODE(000001C7): acct_session_id: 724
    *Mar  8 00:03:06.819: RADIUS(000001C7): sending
    *Mar  8 00:03:06.819: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
    *Mar  8 00:03:06.819: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/83, len 251
    *Mar  8 00:03:06.819: RADIUS:  authenticator A1 79 FA E5 F4 B7 7F 4F - 2B 73 3A 0D 1F D8 89 20
    *Mar  8 00:03:06.819: RADIUS:  User-Name           [1]   31  "host/D0902MALL005.IN.intranet"
    *Mar  8 00:03:06.819: RADIUS:  Service-Type        [6]   6   Framed                    [2]
    *Mar  8 00:03:06.819: RADIUS:  Framed-MTU          [12]  6   1500                     
    *Mar  8 00:03:06.819: RADIUS:  Called-Station-Id   [30]  19  "D4-A0-2A-EE-14-81"
    *Mar  8 00:03:06.819: RADIUS:  Calling-Station-Id  [31]  19  "D4-3D-7E-65-4F-C1"
    *Mar  8 00:03:06.819: RADIUS:  EAP-Message         [79]  36 
    *Mar  8 00:03:06.819: RADIUS:   02 01 00 22 01 68 6F 73 74 2F 44 30 39 30 32 4D 41 4C 4C 30  ["host/D0902MALL0]
    *Mar  8 00:03:06.819: RADIUS:   30 35 2E 49 4E 2E 69 6E 74 72 61 6E 65 74    [ 05.IN.intranet]
    *Mar  8 00:03:06.819: RADIUS:  Message-Authenticato[80]  18 
    *Mar  8 00:03:06.819: RADIUS:   D6 6F 7B CD 36 46 5E F6 90 6F 85 A8 BD BD AE D8            [ o{6F^o]
    *Mar  8 00:03:06.819: RADIUS:  EAP-Key-Name        [102] 2   *
    *Mar  8 00:03:06.819: RADIUS:  Vendor, Cisco       [26]  49 
    *Mar  8 00:03:06.819: RADIUS:   Cisco AVpair       [1]   43  "audit-session-id=0A1AED0B000000EE240F5BAB"
    *Mar  8 00:03:06.819: RADIUS:  NAS-Port-Type       [61]  6   Ethernet                  [15]
    *Mar  8 00:03:06.819: RADIUS:  NAS-Port            [5]   6   50001                    
    *Mar  8 00:03:06.819: RADIUS:  NAS-Port-Id         [87]  17  "FastEthernet0/1"
    *Mar  8 00:03:06.819: RADIUS:  NAS-IP-Address      [4]   6   10.26.237.11             
    *Mar  8 00:03:06.819: RADIUS:  Acct-Session-Id     [44]  10  "000002D4"
    *Mar  8 00:03:06.819: RADIUS(000001C7): Started 3 sec timeout
    *Mar  8 00:03:06.861: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
    *Mar  8 00:03:06.903: RADIUS: Received from id 1645/83 10.26.13.59:1812, Access-Challenge, len 76
    *Mar  8 00:03:06.903: RADIUS:  authenticator 7B 1C DC CA A8 92 E9 34 - 17 86 25 2F 9D 7E 63 96
    *Mar  8 00:03:06.903: RADIUS:  EAP-Message         [79]  8  
    *Mar  8 00:03:06.903: RADIUS:   01 02 00 06 0D 20                 [  ]
    *Mar  8 00:03:06.903: RADIUS:  Message-Authenticato[80]  18 
    *Mar  8 00:03:06.903: RADIUS:   DD F3 7B 33 37 6D 40 BD F3 D2 78 DF F1 14 4D E4           [ {37m@xM]
    *Mar  8 00:03:06.903: RADIUS:  State               [24]  30 
    *Mar  8 00:03:06.903: RADIUS:   00 7D 00 9B 00 C1 00 40 ED B8 45 00 FC DD 50 2E DC 0E E6 03 FC 7B AD 4C B7 E7 B1 70          [ }@EP.{Lp]
    *Mar  8 00:03:06.911: RADIUS(000001C7): Received from id 1645/83
    *Mar  8 00:03:06.911: RADIUS/DECODE: EAP-Message fragments, 6, total 6 bytes
    *Mar  8 00:03:06.911: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
    *Mar  8 00:03:06.911:     dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
    *Mar  8 00:03:06.911: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
    *Mar  8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
    *Mar  8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
    *Mar  8 00:03:06.911: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:06.911: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:06.911: dot1x-registry:registry:dot1x_ether_macaddr called
    *Mar  8 00:03:06.911: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:06.911: EAPOL pak dump Tx
    *Mar  8 00:03:06.911: EAPOL Version: 0x3  type: 0x0  length: 0x0006
    *Mar  8 00:03:06.911: EAP code: 0x1  id: 0x2  length: 0x0006 type: 0xD
    *Mar  8 00:03:06.911: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
    *Mar  8 00:03:06.920: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:06.920: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
    *Mar  8 00:03:06.920: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
    *Mar  8 00:03:06.920: EAPOL pak dump rx
    *Mar  8 00:03:06.920: EAPOL Version: 0x1  type: 0x0  length: 0x0069
    *Mar  8 00:03:06.920: dot1x-ev:
    dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 105
    *Mar  8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAPOL frame
    *Mar  8 00:03:06.920: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
        pae-ether-type = 888e.0100.0069
    *Mar  8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAP packet
    *Mar  8 00:03:06.920: EAPOL pak dump rx
    *Mar  8 00:03:06.920: EAPOL Version: 0x1  type: 0x0  length: 0x0069
    *Mar  8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
    *Mar  8 00:03:06.920: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
    *Mar  8 00:03:06.920:     dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
    *Mar  8 00:03:06.920: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
    *Mar  8 00:03:06.920: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
    *Mar  8 00:03:06.920: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:06.920: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
    *Mar  8 00:03:06.920: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
    *Mar  8 00:03:06.920: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
    *Mar  8 00:03:06.920: RADIUS(000001C7): Config NAS IP: 0.0.0.0
    *Mar  8 00:03:06.920: RADIUS/ENCODE(000001C7): acct_session_id: 724
    *Mar  8 00:03:06.920: RADIUS(000001C7): sending
    *Mar  8 00:03:06.920: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
    *Mar  8 00:03:06.920: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/84, len 352
    *Mar  8 00:03:06.920: RADIUS:  authenticator 41 72 8D 6A B4 72 19 84 - 1B C8 33 F7 95 DD 07 BC
    *Mar  8 00:03:06.928: RADIUS:  User-Name           [1]   31  "host/D0902MALL005.IN.intranet"
    *Mar  8 00:03:06.928: RADIUS:  Service-Type        [6]   6   Framed                    [2]
    *Mar  8 00:03:06.928: RADIUS:  Framed-MTU          [12]  6   1500                     
    *Mar  8 00:03:06.928: RADIUS:  Called-Station-Id   [30]  19  "D4-A0-2A-EE-14-81"
    *Mar  8 00:03:06.928: RADIUS:  Calling-Station-Id  [31]  19  "D4-3D-7E-65-4F-C1"
    *Mar  8 00:03:06.928: RADIUS:  EAP-Message         [79]  107
    *Mar  8 00:03:06.928: RADIUS:   02 02 00 69 0D 80 00 00 00 5F 16 03 01 00 5A 01 00 00 56 03 01 52 C5 45 4F 07 CA B3 29 50 A7 CE 40 76 B6 BD F0 50 D4 CE 9A 8A 02 C4 3D 40 35 B5 F0 E1 E2 75  [i_ZVREO)P@vP=@5u]
    *Mar  8 00:03:06.928: RADIUS:   50 00 00 18 00 2F 00 35 00 05 00 0A C0 13 C0 14 C0 09 C0 0A 00 32 00 38 00 13 00 04 01 00 00 15 FF 01 00 01 00 00 0A 00 06 00 04 00 17 00 18 00 0B 00 02 01 00             [ P/528]
    *Mar  8 00:03:06.928: RADIUS:  Message-Authenticato[80]  18 
    *Mar  8 00:03:06.928: RADIUS:   A3 28 CE 27 20 C0 D6 2C 11 01 D6 61 1F C3 6F 03            [ (' ,ao]
    *Mar  8 00:03:06.928: RADIUS:  EAP-Key-Name        [102] 2   *
    *Mar  8 00:03:06.928: RADIUS:  Vendor, Cisco       [26]  49 
    *Mar  8 00:03:06.928: RADIUS:   Cisco AVpair       [1]   43  "audit-session-id=0A1AED0B000000EE240F5BAB"
    *Mar  8 00:03:06.928: RADIUS:  NAS-Port-Type       [61]  6   Ethernet                  [15]
    *Mar  8 00:03:06.928: RADIUS:  NAS-Port            [5]   6   50001                    
    *Mar  8 00:03:06.928: RADIUS:  NAS-Port-Id         [87]  17  "FastEthernet0/1"
    *Mar  8 00:03:06.928: RADIUS:  State               [24]  30 
    *Mar  8 00:03:06.928: RADIUS:   00 7D 00 9B 00 C1 00 40 ED B8 45 00 FC DD 50 2E DC 0E E6 03 FC 7B AD 4C B7 E7 B1 70          [ }@EP.{Lp]
    *Mar  8 00:03:06.928: RADIUS:  NAS-IP-Address      [4]   6   10.26.237.11             
    *Mar  8 00:03:06.928: RADIUS:  Acct-Session-Id     [44]  10  "000002D4"
    *Mar  8 00:03:06.928: RADIUS(000001C7): Started 3 sec timeout
    *Mar  8 00:03:07.004: RADIUS: Received from id 1645/84 10.26.13.59:1812, Access-Challenge, len 1188
    *Mar  8 00:03:07.004: RADIUS:  authenticator 7B 52 29 05 7E C3 EF 8E - 13 38 30 03 4B 65 64 0F
    *Mar  8 00:03:07.004: RADIUS:  EAP-Message         [79]  255
    *Mar  8 00:03:07.004: RADIUS:   01 03 04 56 0D C0 00 00 05 78 16 03 01 00 51 02 00 00 4D 03 01 52 C5 45 4F 0F 04 37 77 A0 C2 68 66 4E 45 92 AB 3D 7F 94 70 AF 36  [VxQMREO7whfNE=p6]
    *Mar  8 00:03:07.004: RADIUS:   1D C5 17 23 5C F1 FA CA 60 B0 20 A5 48 16 D5 3F F9 B0 FF 38 1D D5 13 B3 88 13 06 EF DC 87 5C AE 17 E7 7E 80 84 21 58 64 F7 A6 36 00 35 00 00 05 FF 01 00 01 00 16 03 01 02 1C 0B 00 02 18 00 02 15 00 02 12 30 82 02 0E 30  [#\` H?8\~!Xd6500]
    *Mar  8 00:03:07.004: RADIUS:   82 01 77 A0 03 02 01 02 02 09 00 88 7A CB 35 3F 1E 3E 62 30 0D 06 09 2A 86 48 86 F7 0D 01 01 05 05 00 30 2F 31 15 30 13 06 03 55 04 03 13 0C 53 50  [wz5?>b0*H0/10USP]
    *Mar  8 00:03:07.004: RADIUS:   49 4E 41 56 44 30 30 30 30 34 31 16 30 14 06 03 55 04 0A 13 0D 50 6F 6C  [INAVD0000410UPol]
    *Mar  8 00:03:07.004: RADIUS:   69 63 79 4D 61 6E 61 67 65 72 30 1E 17 0D 31 33 30 38 32  [icyManager013082]
    *Mar  8 00:03:07.004: RADIUS:   37 30 37 32 34 33 30 5A 17 0D 31 34 30 38 32 37 30 37  [7072430Z14082707]
    *Mar  8 00:03:07.004: RADIUS:   32 34 33 30 5A 30 2F 31 15 30 13 06 03 55 04 03 13 0C 53 50 49 4E 41 56  [2430Z0/10USPINAV]
    *Mar  8 00:03:07.004: RADIUS:   44 30 30               [ D00]
    *Mar  8 00:03:07.004: RADIUS:  EAP-Message         [79]  255
    *Mar  8 00:03:07.004: RADIUS:   30 30 34 31 16 30 14 06 03 55 04 0A 13 0D 50 6F 6C 69 63 79 4D 61 6E 61  [00410UPolicyMana]
    *Mar  8 00:03:07.004: RADIUS:   67 65 72 30 81 9F 30 0D 06 09 2A 86 48 86 F7 0D 01 01 01 05 00 03 81 8D 00 30 81 89 02 81 81 00 C9 B9 03 65 83 EB 39 86 14 BC 95 7B DB 07 7E C5 8A D7 DA C7 8A CA 5A 88 6E 0B 93 06 35 57  [ger00*H0e9{~Zn5W]
    *Mar  8 00:03:07.012: RADIUS:   6E DE 93 CD C9 FE 8E 9F E1 5F A9 04 5C BD A9 AD 5A 04 6E 35 47 76 A1 58 E5 C4 32 D7 49 9E 17 75 20 C6 6F 45 40  [n_\Zn5GvX2Iu oE@]
    *Mar  8 00:03:07.012: RADIUS:   AC EF 40 6D 15 38 F9 C2 28 7E C9 68 37 52 3B BF F4 C1 5E B8 BA 46 68 43 79 B1 65 66  [@m8(~h7R;^FhCyef]
    *Mar  8 00:03:07.012: RADIUS:   9E 58 ED EC 8C 95 A2 D8 BF AA 77 AC 85 90 E3 AB C6 27 3A A2 22 AC 1C 48 B3 BF BE F7 85 CF 5C BB 2D 02 03 01 00 01 A3 32 30 30 30 0F 06 03 55 1D 11 04 08 30 06 87 04 0A 1A 0D 3B 30  [Xw':"H\-2000U0;0]
    *Mar  8 00:03:07.012: RADIUS:   1D 06 03 55 1D 25 04 16 30 14 06 08 2B 06 01 05 05 07 03 01 06 08 2B 06 01 05 05 07 03 03 30 0D 06 09 2A 86 48 86 F7 0D 01 01          [ U?0++0*H]
    *Mar  8 00:03:07.012: RADIUS:  EAP-Message         [79]  255
    *Mar  8 00:03:07.012: RADIUS:   05 05 00 03 81 81 00 C4 46 3E 38 3D 53 0F 28 34 C1 A6 ED DC 70 76 9B 70 6B A8 95 7C 44 8E 7D 6E D6 8B 6D  [F>8=S(4pvpk|D}nm]
    *Mar  8 00:03:07.012: RADIUS:   90 49 83 06 E4 BF 68 2F 9D 77 78 A3 76 76 19 84 AD 26 3F F3 ED AA 88 52 35 0E 35 DD 00 E5 96 88 44 30 79 A0 71  [Ih/wxvv&?R55D0yq]
    *Mar  8 00:03:07.012: RADIUS:   8D 25 3E 77 A0 E0 43 92 33 55 40 E1 C8 EE 88 11 25 E2 70 28 11 6C 5A 4E 3D F1 93 57 0A 6F  [?>wC3U@?p(lZN=Wo]
    *Mar  8 00:03:07.012: RADIUS:   36 51 72 04 08 C0 C0 DF F0 94 A9 F7 A1 05 C8 37 D6 F8 D4 9C 20 1A 7B CD 2C 17 83 7B 8E 20 F7 2D B6 16 03 01 02 FC 0D 00 02 F4 03 01 02 40 02 EE 00 63 30 61 31 0B 30  [6Qr7 {,{ -@c0a10]
    *Mar  8 00:03:07.012: RADIUS:   09 06 03 55 04 06 13 02 55 53 31 15 30 13 06 03 55 04 0A 13 0C 44 69 67 69 43 65 72 74 20 49  [UUS10UDigiCert I]
    *Mar  8 00:03:07.012: RADIUS:   6E 63 31 19 30 17 06 03 55 04 0B 13 10 77 77 77 2E 64 69 67 69 63 65 72  [nc10Uwww.digicer]
    *Mar  8 00:03:07.012: RADIUS:   74 2E 63 6F 6D 31 20 30 1E 06 03 55 04 03 13 17 44 69 67 69 43 65 72  [t.com1 0UDigiCer]
    *Mar  8 00:03:07.012: RADIUS:   74 20 47 6C 6F 62 61 6C 20 52 6F 6F 74 20 43 41  [t Global Root CA]
    *Mar  8 00:03:07.012: RADIUS:   00 48                 [ H]
    *Mar  8 00:03:07.012: RADIUS:  EAP-Message         [79]  255
    *Mar  8 00:03:07.012: RADIUS:   30 46 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E 74 72 61 6E 65 74 31  [0F10&,dintranet1]
    *Mar  8 00:03:07.020: RADIUS:   12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 16 30 14 06 03 55 04 03 13 0D 49 6E 64 69 61 20 52  [0&,dIN10UIndia R]
    *Mar  8 00:03:07.020: RADIUS:   6F 6F 74 20 43 41 00 4A 30 48 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E  [oot CAJ0H10&,din]
    *Mar  8 00:03:07.020: RADIUS:   74 72 61 6E 65 74 31 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 18 30 16 06 03 55  [tranet10&,dIN10U]
    *Mar  8 00:03:07.020: RADIUS:   04 03 13 0F 45 6E 74 65 72 70 72 69 73 65 20 43 41 2D 31 00 4D  [Enterprise CA-1M]
    *Mar  8 00:03:07.020: RADIUS:   30 4B 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E 74 72 61 6E 65 74 31  [0K10&,dintranet1]
    *Mar  8 00:03:07.020: RADIUS:   12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 1B 30 19 06 03 55 04 03 13 12 49 4E 2D 53 50 49 4E  [0&,dIN10UIN-SPIN]
    *Mar  8 00:03:07.020: RADIUS:   43 52 54 30 30 30 30 33 2D 43 41 00 D5 30 81 D2 31 0B 30 09 06 03 55 04 06 13 02 55  [CRT00003-CA010UU]
    *Mar  8 00:03:07.020: RADIUS:   53 31 13 30 11 06 03 55 04              [ S10U]
    *Mar  8 00:03:07.020: RADIUS:  EAP-Message         [79]  100
    *Mar  8 00:03:07.020: RADIUS:   08 0C 0A 43 61 6C 69 66 6F 72 6E 69 61 31 12 30 10 06 03 55 04 07 0C 09 53 75 6E  [California10USun]
    *Mar  8 00:03:07.020: RADIUS:   6E 79 76 61 6C 65 31 17 30 15 06 03 55 04 0A 0C 0E 41 72 75 62 61 20 4E  [nyvale10UAruba N]
    *Mar  8 00:03:07.020: RADIUS:   65 74 77 6F 72 6B 73 31 40 30 3E 06 03 55 04 03 0C 37 43 6C 65  [etworks1@0>U7Cle]
    *Mar  8 00:03:07.020: RADIUS:   61 72 50 61 73 73 20 4F 6E 62 6F 61 72 64 20 4C  [arPass Onboard L]
    *Mar  8 00:03:07.020: RADIUS:   6F 63 61 6C 20 43 65 72 74 69        [ ocal Certi]
    *Mar  8 00:03:07.020: RADIUS:  Message-Authenticato[80]  18 
    *Mar  8 00:03:07.020: RADIUS:   12 75 40 41 6F 40 6B 6F A5 FE AB 85 F3 B3 CF A4           [ u@Ao@ko]
    *Mar  8 00:03:07.020: RADIUS:  State               [24]  30 
    *Mar  8 00:03:07.020: RADIUS:   00 6F 00 51 00 4B 00 6E EE B8 45 00 4B AA 6B A9 B6 D6 C8 CC 48 1A 91 99 7F 77 D3 C1         [ oQKnEKkHw]
    *Mar  8 00:03:07.029: RADIUS(000001C7): Received from id 1645/84
    *Mar  8 00:03:07.029: RADIUS/DECODE: EAP-Message fragments, 253+253+253+253+98, total 1110 bytes
    *Mar  8 00:03:07.037: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
    *Mar  8 00:03:07.037:     dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
    *Mar  8 00:03:07.037: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
    *Mar  8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
    *Mar  8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
    *Mar  8 00:03:07.037: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:07.037: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:07.037: dot1x-registry:registry:dot1x_ether_macaddr called
    *Mar  8 00:03:07.037: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:07.037: EAPOL pak dump Tx
    *Mar  8 00:03:07.037: EAPOL Version: 0x3  type: 0x0  length: 0x0456
    *Mar  8 00:03:07.037: EAP code: 0x1  id: 0x3  length: 0x0456 type: 0xD
    *Mar  8 00:03:07.037: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
    *Mar  8 00:03:07.037: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:07.037: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
    *Mar  8 00:03:07.037: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
    *Mar  8 00:03:07.037: EAPOL pak dump rx
    *Mar  8 00:03:07.037: EAPOL Version: 0x1  type: 0x0  length: 0x0006
    *Mar  8 00:03:07.037: dot1x-ev:
    dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 6
    *Mar  8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAPOL frame
    *Mar  8 00:03:07.037: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
        pae-ether-type = 888e.0100.0006
    *Mar  8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAP packet
    *Mar  8 00:03:07.037: EAPOL pak dump rx
    *Mar  8 00:03:07.037: EAPOL Version: 0x1  type: 0x0  length: 0x0006
    *Mar  8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
    *Mar  8 00:03:07.037: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
    *Mar  8 00:03:07.037:     dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
    *Mar  8 00:03:07.037: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
    *Mar  8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
    *Mar  8 00:03:07.037: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
    *Mar  8 00:03:07.037: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
    *Mar  8 00:03:07.046: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
    *Mar  8 00:03:07.046: RADIUS(000001C7): Config NAS IP: 0.0.0.0
    *Mar  8 00:03:07.046: RADIUS/ENCODE(000001C7): acct_session_id: 724
    *Mar  8 00:03:07.046: RADIUS(000001C7): sending
    *Mar  8 00:03:07.046: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
    *Mar  8 00:03:07.046: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/85, len 253
    *Mar  8 00:03:07.046: RADIUS:  authenticator 1C D7 6D 40 A3 D6 BA B1 - A7 E6 70 DA 32 83 2E 19
    *Mar  8 00:03:07.046: RADIUS:  User-Name           [1]   31  "host/D0902MALL005.IN.intranet"
    *Mar  8 00:03:07.046: RADIUS:  Service-Type        [6]   6   Framed                    [2]
    *Mar  8 00:03:07.046: RADIUS:  Framed-MTU          [12]  6   1500                     
    *Mar  8 00:03:07.046: RADIUS:  Called-Station-Id   [30]  19  "D4-A0-2A-EE-14-81"
    *Mar  8 00:03:07.046: RADIUS:  Calling-Station-Id  [31]  19  "D4-3D-7E-65-4F-C1"
    *Mar  8 00:03:07.046: RADIUS:  EAP-Message         [79]  8  
    *Mar  8 00:03:07.046: RADIUS:   02 03 00 06 0D 00
    *Mar  8 00:03:07.046: RADIUS:  Message-Authenticato[80]  18 
    *Mar  8 00:03:07.046: RADIUS:   73 1D 89 5C 66 19 32 B6 63 C2 64 C1 04 42 A9 F9           [ s\f2cdB]
    *Mar  8 00:03:07.046: RADIUS:  EAP-Key-Name        [102] 2   *
    *Mar  8 00:03:07.046: RADIUS:  Vendor, Cisco       [26]  49 
    *Mar  8 00:03:07.046: RADIUS:   Cisco AVpair       [1]   43  "audit-session-id=0A1AED0B000000EE240F5BAB"
    *Mar  8 00:03:07.046: RADIUS:  NAS-Port-Type       [61]  6   Ethernet                  [15]
    *Mar  8 00:03:07.046: RADIUS:  NAS-Port            [5]   6   50001                    
    *Mar  8 00:03:07.046: RADIUS:  NAS-Port-Id         [87]  17  "FastEthernet0/1"
    *Mar  8 00:03:07.046: RADIUS:  State               [24]  30 
    *Mar  8 00:03:07.046: RADIUS:   00 6F 00 51 00 4B 00 6E EE B8 45 00 4B AA 6B A9 B6 D6 C8 CC 48 1A 91 99 7F 77 D3 C1         [ oQKnEKkHw]
    *Mar  8 00:03:07.046: RADIUS:  NAS-IP-Address      [4]   6   10.26.237.11             
    *Mar  8 00:03:07.046: RADIUS:  Acct-Session-Id     [44]  10  "000002D4"
    *Mar  8 00:03:07.046: RADIUS(000001C7): Started 3 sec timeout
    *Mar  8 00:03:07.113: RADIUS: Received from id 1645/85 10.26.13.59:1812, Access-Challenge, len 378
    *Mar  8 00:03:07.113: RADIUS:  authenticator 1A 85 26 09 58 84 BC D4 - E0 A9 E3 C0 25 31 2D 31
    *Mar  8 00:03:07.113: RADIUS:  EAP-Message         [79]  255
    *Mar  8 00:03:07.121: RADIUS:   01 04 01 32 0D 00 66 69 63 61 74 65 20 41 75 74 68 6F 72 69 74  [2ficate Authorit]
    *Mar  8 00:03:07.121: RADIUS:   79 20 28 53 69 67 6E 69 6E 67 29 31 3F 30 3D 06 09 2A  [y (Signing)1?0=*]
    *Mar  8 00:03:07.121: RADIUS:   86 48 86 F7 0D 01 09 01 16 30 64 36 62 62 34 66 37 30 2D 66 34 31 32 2D  [H0d6bb4f70-f412-]
    *Mar  8 00:03:07.121: RADIUS:   34 35 35 32 2D 61 65 65 32 2D 63 37 61 30 32 36  [4552-aee2-c7a026]
    *Mar  8 00:03:07.121: RADIUS:   66 62 61 32 31 38 40 65 78 61 6D 70 6C 65 2E 63  [[email protected]]
    *Mar  8 00:03:07.121: RADIUS:   6F 6D 00 CB 30 81 C8 31 0B 30 09 06 03 55 04 06 13 02 55 53 31 13 30 11 06 03 55 04 08 0C 0A 43 61 6C 69 66  [om010UUS10UCalif]
    *Mar  8 00:03:07.121: RADIUS:   6F 72 6E 69 61 31 12 30 10 06 03 55 04 07 0C 09 53 75 6E 6E 79 76 61 6C  [ornia10USunnyval]
    *Mar  8 00:03:07.121: RADIUS:   65 31 17 30 15 06 03 55 04 0A 0C 0E 41 72 75 62 61 20 4E 65 74 77 6F 72  [e10UAruba Networ]
    *Mar  8 00:03:07.121: RADIUS:   6B 73 31 36 30 34 06 03 55 04 03 0C 2D 43 6C 65 61 72 50 61 73  [ks1604U-ClearPas]
    *Mar  8 00:03:07.121: RADIUS:   73 20 4F 6E 62 6F 61 72 64 20 4C 6F 63 61 6C 20  [s Onboard Local ]
    *Mar  8 00:03:07.121: RADIUS:   43 65 72 74 69 66 69 63 61 74 65 20 41 75 74 68  [Certificate Auth]
    *Mar  8 00:03:07.121: RADIUS:   6F 72 69 74 79 31 3F 30 3D 06 09 2A 86 48 86 F7 0D 01 09 01 16       [ ority1?0=*H]
    *Mar  8 00:03:07.121: RADIUS:  EAP-Message         [79]  55 
    *Mar  8 00:03:07.121: RADIUS:   30 64 36 62 62 34 66 37 30 2D 66 34 31 32 2D 34  [0d6bb4f70-f412-4]
    *Mar  8 00:03:07.121: RADIUS:   35 35 32 2D 61 65 65 32 2D 63 37 61 30 32 36 66  [552-aee2-c7a026f]
    *Mar  8 00:03:07.121: RADIUS:   62 61 32 31 38 40 65 78 61 6D 70 6C 65 2E 63 6F  [[email protected]]
    *Mar  8 00:03:07.121: RADIUS:   6D 0E 00 00 00                 [ m]
    *Mar  8 00:03:07.121: RADIUS:  Message-Authenticato[80]  18 
    *Mar  8 00:03:07.121: RADIUS:   4C 46 AA B9 A5 D5 DF EA DB E7 2B 7B 51 7E 58 3F          [ LF+{Q~X?]
    *Mar  8 00:03:07.121: RADIUS:  State               [24]  30 
    *Mar  8 00:03:07.121: RADIUS:   00 EF 00 B9 00 0A 00 00 EF B8 45 00 EF D2 C4 3C 81 6C 72 0E 23 FE 11 EA 12 17 50 A1            [ E
    *Mar  8 00:03:07.121: RADIUS(000001C7): Received from id 1645/85
    *Mar  8 00:03:07.121: RADIUS/DECODE: EAP-Message fragments, 253+53, total 306 bytes
    *Mar  8 00:03:07.130: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
    *Mar  8 00:03:07.130:     dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
    *Mar  8 00:03:07.130: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
    *Mar  8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
    *Mar  8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
    *Mar  8 00:03:07.130: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:07.130: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:07.130: dot1x-registry:registry:dot1x_ether_macaddr called
    *Mar  8 00:03:07.130: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:07.130: EAPOL pak dump Tx
    *Mar  8 00:03:07.130: EAPOL Version: 0x3  type: 0x0  length: 0x0132
    *Mar  8 00:03:07.130: EAP code: 0x1  id: 0x4  length: 0x0132 type: 0xD
    *Mar  8 00:03:07.130: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
    *Mar  8 00:03:07.138: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:07.138: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
    *Mar  8 00:03:07.138: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
    *Mar  8 00:03:07.138: EAPOL pak dump rx
    *Mar  8 00:03:07.138: EAPOL Version: 0x1  type: 0x0  length: 0x05D4
    *Mar  8 00:03:07.138: dot1x-ev:
    dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 1492
    *Mar  8 00:03:07.138: dot1x-packet(Fa0/1): Received an EAPOL frame
    *Mar  8 00:03:07.138: dot1x-ev(Fa0/1):
    ^Z
    Malleswaram_2960#
    *Mar  8 00:03:07.180: RADIUS:  State               [24]  30 
    *Mar  8 00:03:07.180: RADIUS:   00 EF 00 B9 00 0A 00 00 EF B8 45 00 EF D2 C4 3C 81 6C 72 0E 23 FE 11 EA 12 17 50 A1            [ E
    *Mar  8 00:03:07.180: RADIUS:  NAS-IP-Address      [4]   6   10.26.237.11             
    *Mar  8 00:03:07.180: RADIUS:  Acct-Session-Id     [44]  10  "000002D4"
    *Mar  8 00:03:07.180: RADIUS(000001C7): Started 3 sec timeout
    Malleswaram_2960#
    *Mar  8 00:03:07.893: %SYS-5-CONFIG_I: Configured from console by jameela on vty0 (10.26.20.5)
    Malleswaram_2960#
    *Mar  8 00:03:10.225: RADIUS(000001C7): Request timed out
    *Mar  8 00:03:10.225: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
    *Mar  8 00:03:10.225: RADIUS(000001C7): Started 3 sec timeout
    Malleswaram_2960#
    *Mar  8 00:03:13.354: RADIUS(000001C7): Request timed out
    *Mar  8 00:03:13.354: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
    *Mar  8 00:03:13.354: RADIUS(000001C7): Started 3 sec timeout
    Malleswaram_2960#
    *Mar  8 00:03:16.307: RADIUS(000001C7): Request timed out
    *Mar  8 00:03:16.307: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
    *Mar  8 00:03:16.307: RADIUS(000001C7): Started 3 sec timeout
    Malleswaram_2960#
    *Mar  8 00:03:19.369: RADIUS(000001C7): Request timed out
    *Mar  8 00:03:19.369: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
    *Mar  8 00:03:19.369: RADIUS(000001C7): Started 3 sec timeout
    Malleswaram_2960#
    *Mar  8 00:03:22.456: RADIUS(000001C7): Request timed out
    *Mar  8 00:03:22.456: RADIUS: Fail-over denied to  (10.26.13.59:1812,1813) for id 1645/86
    *Mar  8 00:03:22.456: RADIUS: No response from (10.26.13.59:1812,1813) for id 1645/86
    *Mar  8 00:03:22.456: RADIUS/DECODE: parse response no app start; FAIL
    *Mar  8 00:03:22.456: RADIUS/DECODE: parse response; FAIL
    *Mar  8 00:03:22.456: dot1x-ev(Fa0/1): Received an EAP Fail
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): Posting EAP_FAIL for 0xB0000DBA
    *Mar  8 00:03:22.456:     dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 10(eapFail)
    *Mar  8 00:03:22.456: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_fail
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_fail_enter called
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_fail_action called
    *Mar  8 00:03:22.456:     dot1x_auth_bend Fa0/1: idle during state auth_bend_fail
    *Mar  8 00:03:22.456: @@@ dot1x_auth_bend Fa0/1: auth_bend_fail -> auth_bend_idle
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): Posting AUTH_FAIL on Client 0xB0000DBA
    *Mar  8 00:03:22.456:     dot1x_auth Fa0/1: during state auth_authenticating, got event 15(authFail)
    *Mar  8 00:03:22.456: @@@ dot1x_auth Fa0/1: auth_authenticating -> auth_authc_result
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_exit called
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authc_result_enter called
    *Mar  8 00:03:22.456: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
    *Mar  8 00:03:22.456: dot1x-ev(Fa0/1): Sending event (2) to Auth Mgr for d43d.7e65.4fc1
    *Mar  8 00:03:22.456: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
    *Mar  8 00:03:22.456: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
    *Mar  8 00:03:22.456: dot1x-redundancy: State for client  d43d.7e65.4fc1 successfully retrieved
    *Mar  8 00:03:22.456: dot1x-ev(Fa0/1): Received Authz fail for the client  0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): Posting_AUTHZ_FAIL on Client 0xB0000DBA
    *Mar  8 00:03:22.456:     dot1x_auth Fa0/1: during state auth_authc_result, got event 22(authzFail)
    *Mar  8 00:03:22.456: @@@ dot1x_auth Fa0/1: auth_authc_result -> auth_held
    *Mar  8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_enter called
    *Mar  8 00:03:22.464: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:22.464: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:22.464: dot1x-registry:registry:dot1x_ether_macaddr called
    *Mar  8 00:03:22.464: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:22.464: EAPOL pak dump Tx
    *Mar  8 00:03:22.464: EAPOL Version: 0x3  type: 0x0  length: 0x0004
    *Mar  8 00:03:22.464: EAP code: 0x4  id: 0x4  length: 0x0004
    *Mar  8 00:03:22.464: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): Posting FAILOVER_RETRY on Client 0xB0000DBA
    *Mar  8 00:03:22.464:     dot1x_auth Fa0/1: during state auth_held, got event 21(failover_retry)
    *Mar  8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_held -> auth_restart
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_exit called
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
    *Mar  8 00:03:22.464: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_restart_action called
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
    *Mar  8 00:03:22.464:     dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
    *Mar  8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): Posting REAUTH_MAX on Client 0xB0000DBA
    *Mar  8 00:03:22.464:     dot1x_auth Fa0/1: during state auth_connecting, got event 11(reAuthMax)
    *Mar  8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_disconnected
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_disconnected_enter called
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): d43d.7e65.4fc1:auth_disconnected_enter sending canned failure to version 1 supplicant
    *Mar  8 00:03:22.464: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:22.464: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:22.464: dot1x-registry:registry:dot1x_ether_macaddr called
    *Mar  8 00:03:22.464: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:22.464: EAPOL pak dump Tx
    *Mar  8 00:03:22.464: EAPOL Version: 0x3  type: 0x0  length: 0x0004
    *Mar  8 00:03:22.464: EAP code: 0x4  id: 0x5  length: 0x0004
    *Mar  8 00:03:22.464: dot1x-packet(Fa0/1): dot1x_auth_txCannedStatus: EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
    *Mar  8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_disconnected_reAuthMax_action called
    *Mar  8 00:03:22.464:     dot1x_auth Fa0/1: idle during state auth_disconnected
    *Mar  8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
    *Mar  8 00:03:22.464: dot1x-ev(Fa0/1): Sending event (1) to Auth Mgr for d43d.7e65.4fc1
    *Mar  8 00:03:22.464: dot1x-ev:Delete auth client (0xB0000DBA) message
    *Mar  8 00:03:22.464: dot1x-ev:Auth client ctx destroyed
    *Mar  8 00:03:22.674: AAA/BIND(000001C8): Bind i/f 
    *Mar  8 00:03:22.674:     dot1x_auth Fa0/1: initial state auth_initialize has enter
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_initialize_enter called
    *Mar  8 00:03:22.674:     dot1x_auth Fa0/1: during state auth_initialize, got event 0(cfg_auto)
    *Mar  8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_initialize -> auth_disconnected
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_disconnected_enter called
    *Mar  8 00:03:22.674:     dot1x_auth Fa0/1: idle during state auth_disconnected
    *Mar  8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_restart_enter called
    *Mar  8 00:03:22.674: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0x4A000DBB (0000.0000.0000)
    *Mar  8 00:03:22.674:     dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has enter
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_initialize_enter called
    *Mar  8 00:03:22.674:     dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has idle
    *Mar  8 00:03:22.674:     dot1x_auth_bend Fa0/1: during state auth_bend_initialize, got event 16383(idle)
    *Mar  8 00:03:22.674: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_idle_enter called
    *Mar  8 00:03:22.674: dot1x-ev(Fa0/1): Created a client entry (0x4A000DBB)
    *Mar  8 00:03:22.674: dot1x-ev(Fa0/1): Dot1x authentication started for 0x4A000DBB (0000.0000.0000)
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0x4A000DBB
    *Mar  8 00:03:22.674:     dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
    *Mar  8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_connecting_enter called
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_restart_connecting_action called
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0x4A000DBB
    *Mar  8 00:03:22.674:     dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
    *Mar  8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_authenticating_enter called
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_connecting_authenticating_action called
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): Posting AUTH_START for 0x4A000DBB
    *Mar  8 00:03:22.674:     dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
    *Mar  8 00:03:22.674: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
    *Mar  8 00:03:22.674: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:22.674: dot1x-ev(Fa0/1): Role determination not required
    Malleswaram_2960#
    *Mar  8 00:03:22.674: dot1x-registry:registry:dot1x_ether_macaddr called
    *Mar  8 00:03:22.674: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:22.674: EAPOL pak dump Tx
    *Mar  8 00:03:22.674: EAPOL Version: 0x3  type: 0x0  length: 0x0005
    *Mar  8 00:03:22.674: EAP code: 0x1  id: 0x1  length: 0x0005 type: 0x1
    *Mar  8 00:03:22.674: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (0000.0000.0000)
    *Mar  8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_idle_request_action called
    *Mar  8 00:03:22.791: dot1x-ev(Fa0/1): New client notification from AuthMgr for 0x4A000DBB - d43d.7e65.4fc1
    *Mar  8 00:03:22.791: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Malleswaram_2960#
    *Mar  8 00:03:25.761: dot1x-sm(Fa0/1): Posting EAP_REQ for 0x4A000DBB
    *Mar  8 00:03:25.761:     dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 7(eapReq)
    *Mar  8 00:03:25.761: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_request
    *Mar  8 00:03:25.761: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_request_action called
    *Mar  8 00:03:25.761: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
    *Mar  8 00:03:25.761: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:25.761: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:25.761: dot1x-registry:registry:dot1x_ether_macaddr called
    Malleswaram_2960#n
    *Mar  8 00:03:25.761: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:25.761: EAPOL pak dump Tx
    *Mar  8 00:03:25.761: EAPOL Version: 0x3  type: 0x0  length: 0x0005
    *Mar  8 00:03:25.761: EAP code: 0x1  id: 0x1  length: 0x0005 type: 0x1
    *Mar  8 00:03:25.761: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (d43d.7e65.4fc1)
    Malleswaram_2960#no debu
    Malleswaram_2960#no debug
    *Mar  8 00:03:28.848: dot1x-sm(Fa0/1): Posting EAP_REQ for 0x4A000DBB
    *Mar  8 00:03:28.848:     dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 7(eapReq)
    *Mar  8 00:03:28.848: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_request
    *Mar  8 00:03:28.848: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_request_action called
    *Mar  8 00:03:28.848: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
    *Mar  8 00:03:28.848: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
    *Mar  8 00:03:28.848: dot1x-ev(Fa0/1): Role determination not required
    *Mar  8 00:03:28.848: dot1x-registry:registry:dot1x_ether_macaddr called
    Malleswaram_2960#no debug all
    *Mar  8 00:03:28.848: dot1x-ev(Fa0/1): Sending out EAPOL packet
    *Mar  8 00:03:28.848: EAPOL pak dump Tx
    *Mar  8 00:03:28.848: EAPOL Version: 0x3  type: 0x0  length: 0x0005
    *Mar  8 00:03:28.848: EAP code: 0x1  id: 0x1  length: 0x0005 type: 0x1
    *Mar  8 00:03:28.848: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (d43d.7e65.4fc1)
    Malleswaram_2960#no debug all
    All possible debugging has been turned off
    Malleswaram_2960#
    *Mar  8 00:03:31.180: AAA: parse name=tty1 idb type=-1 tty=-1
    *Mar  8 00:03:31.180: AAA: name=tty1 flags=0x11 type=5 shelf=0 slot=0 adapter=0 port=1 channel=0
    *Mar  8 00:03:31.180: AAA/MEMORY: create_user (0x21D1684) user='jameela' ruser='Malleswaram_2960' ds0=0 port='tty1' rem_addr='10.26.20.5' authen_type=ASCII service=NONE priv=15 initial_task_id='0', vrf= (id=0) key=C9A1F1D1
    *Mar  8 00:03:31.389: TAC+: (-1901802859): received author response status = PASS_ADD
    *Mar  8 00:03:31.389: AAA/MEMORY: free_user (0x21D1684) user='jameela' ruser='Malleswaram_2960' port='tty1' rem_addr='10.26.20.5' authen_type=ASCII service=NONE priv=15
    *Mar  8 00:03:31.935: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
    *Mar  8 00:03:31.935: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    *Mar  8 00:03:31.935: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    *Mar  8 00:03:31.935: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Malleswaram_2960#
    *Mar  8 00:03:31.935: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Malleswaram_2960#no deb
    Malleswaram_2960#no debug al
    Malleswaram_2960#no debug all
    All possible debugging has been turned off
    Malleswaram_2960#
    *Mar  8 00:04:32.677: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Malleswaram_2960#
    *Mar  8 00:04:41.938: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
    *Mar  8 00:04:41.938: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    *Mar  8 00:04:41.938: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    *Mar  8 00:04:41.938: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Malleswaram_2960#
    *Mar  8 00:04:41.938: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Malleswaram_2960#
    *Mar  8 00:05:42.654: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Malleswaram_2960#
    *Mar  8 00:05:51.915: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
    *Mar  8 00:05:51.915: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    *Mar  8 00:05:51.915: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    *Mar  8 00:05:51.915: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Malleswaram_2960#
    *Mar  8 00:05:51.915: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
    Pls dont worry about day and time.

Maybe you are looking for

  • EMC Initialization failed: WinRM HTTP error 403

    We have an existing 2003R2 server running Exchange 2007. I have just installed a new 2012 R2 server with Exchange 2010 SP3 RU8v2. Opening the EMC on this new server yields the following error: Connecting to remote server XXXXX.DOMAIN.LOCAL failed wit

  • Can't install audio content any idea?

    Hi I don't understand this. I installed first audio content in final cut but it is asking put second cd. I did that. But there is only one way to get through is can't eject cd 1 . is i drag n drop this. cd 1 is out but when i put cd 2 in it is cancel

  • Using a SQL Query Group by is needed

    Hi All, Scenario Below: we have 2 Transactions, 5 Lines and each line is having 2 Taxes correspondingly. We have few more formula columns which are calculating based on requirements. We need to Group the amount at Line level for the one specific TAX.

  • Checking whether checkbox is inactive

    Hello! My report outputs lines from DB to a list. In the list, there are lines with checkboxes. I mark a checkbox -> do an operation on the specified line -> return to the list. I make the checkbox in the line inactive through the following statement

  • Previous purchase price in PO -

    Hi Friends, How to get previous purchase price in PO as item wise. 1 time -Ex. Material A , net price=5000 2-time - if i will put Material A for purchase , system have to show me my last (Previous) purchase price of this material is 5000. Regards, MA