Cisco 3545 MCU/EMP

Hello all,
I'm deploying a videoconference solution with a Cisco 3545 with one MCU and one EMP. I've done the basic configurations. The MCU has the ip 10.10.0.170 and the EMP with the 10.10.0.171, mask 255.255.255.240. The problem is that the EMP card never appears in the Media Processing tab in the MCU of the MCU admin page, and on the EMP console keeps popping up the message "NO MCU detected at this IP address: 10.10.0.170".
Do you have any idea?
Best regards.

I was just troubleshooting a video issue recently, and although our problems were different, I learned a few troubleshooting tools.
1. Go on your MCU and see if you can schedule Video meetings directly on the MCU, just to see if that piece works.
2. If that is working, go on your Video Admin web interface and go under Admin/Resource Management...click the MCU tab and then click on the link to the MCU. There is an Update button down there. Click the Update button, then try again.
What I have discovered is if that at any point your restart your MCU and don't click that Update button after, the Video Admin will get out of sync with the MCU and not be able to schedule Video.
So that is something to try to start with.

Similar Messages

  • 3545 MCU is not getting up

    Hello
    I am using Cisco 3545 MCU , but it is showing wakeup configuration mode after getting disconnected while upgrading the software. please help me out
    Regards
    Subhasis

    Hi,
    My cloning is completed successfully but my apps listener is not getting up?? What is
    the problem ?Please run AutoConfig and make sure it completes successfully. Also,make sure your FND_NODES table have correct entries -- Steps To Clean Nonexistent Nodes Or IP Addresses From FND_NODES [ID 260887.1]
    What is the error you get? Do you have all the services up and running?
    Please post the complete error message along with any error messages from listener log file.
    Thanks,
    Hussein

  • Cisco 3515 MCU video output scrambled

    Dear Experts,
    Here wr are facing problem in Cisco MCU 3515 box, when we are taking more than five people in conference the video output is getting scrambled.
    Looking for your suggestinos for work arround of this problem.
    Thanks & Regards,
    Pradipat.

    Try this link:
    http://www.cisco.com/en/US/products/hw/video/ps1870/products_administration_guide_chapter09186a008070bf25.html

  • 3545 MCU v5.7 with Tandberg TMS v11

    Hello.
    Does anyone know of any compatibility issues between TMS v11 and 3545 v5.7?
    I know that TMS v11 has been tested with v5.1.0.0.16 but nothing found about v5.7.
    Cheers
    David

  • Cascading cisco 3510 mcu to an accord mcu

    Has anyone done this?...We are having difficulty doing this. We get audio but no video. I cannot find a document on cisco's web site on how to do this....Can anyone help?

    Media Termination Points extend supplementary services, such as call hold, call transfer, call park, and conferencing, that are otherwise not available when a call is routed to an H.323 endpoint. Some H.323 gateways may require that calls use an MTP to enable supplementary call services, but normally, Cisco IOS gateways do not.
    The Cisco IP Voice Media Streaming Application MTP accepts two full-duplex G.711 Coder-Decoder (CODEC) stream connections. MTPs bridge the media streams between two connections. The streaming data that is received from the input stream on one connection passes to the output stream on the other connection and vice versa. In addition, the MTP trancodes a-law to mu-law (and vice versa) and adjusts packet sizes as required by the two connections.

  • Cisco MCU 3545 Software Upgrade from 5.5 to 5.7 Failure

    Hi Guys,
    When upgrading an 3545 MCU from 5.5 to 5.7 using the upgrade utility the upgrade failed and the  MCU has become unavailable (luckily we were testing this in the lab).  Upon connecting to console and rebooting we get the following error:
    Main application started. Please wait...
    Invalid application on Flash. Running Wakeup program.
    And then it does nothing. Does not respond to HTTP or SNMP and is  unusable. We can't perform the upgrade again as SNMP does not work.
    Is there a way to restore the application to flash, via console or TFTP?  I haven't had any luck finding documentation on this.
    I can telnet to the MCU and login, but from there I don't see what else  I can do. Does anyone on here have experience with this?
    Kind Regards,
    Giles

    Adobe - Lightroom : For Macintosh : Adobe Photoshop Lightroom 5.7.1
    This is the official perpetual update download link.
    It will also be a good idea to bookmark the following link, which provides official details of all Lightroom / ACR developments.
    Lightroom Journal | Tips and advice straight from the Lightroom team.

  • Cannot dial MCU 3545

    Hi
    PLEASE IGNORE/CLOSE THIS THREAD
    I have configured IOS gatekeeper with 2 zone, one for video, the other for mcu.
    3545 MCU configured to register with Service Prefixs, 71,80, 81, 82, 83, 84 and I can see that they are reigistering with IOS gatekeeper as E164 IDs. See below:
    UK-LON-GK01#sh gatekeeper endpoints circuits
    GATEKEEPER ENDPOINT REGISTRATION
    ================================
    CallSignalAddr Port RASSignalAddr Port Zone Name Type Flags
    192.168.71.5 1720 192.168.71.5 1719 LON-GK1-MCU1 MCU
    H323-ID: Cisco MCU-192168071005
    E164-ID: 72
    E164-ID: 85
    E164-ID: 84
    E164-ID: 80
    E164-ID: 81
    192.168.71.10 62527 192.168.71.10 59122 LON-GK1-MCU1 H323-GW
    H323-ID: RasAggregator_1#_LON-GK1-MCU1_1
    Voice Capacity Max.= Avail.= Current.= 0
    192.168.71.10 62528 192.168.71.10 59122 LON-GK1-VIDEO1 H323-GW
    H323-ID: RasAggregator_1#_LON-GK1-VIDEO1_1
    Voice Capacity Max.= Avail.= Current.= 0
    192.168.70.30 1720 192.168.70.30 1719 LON-GK1-VIDEO1 TERM
    H323-ID: London5
    E164-ID: 5978
    Total number of active registrations = 4
    When I dial any of the Service Prefixes, from the Tandberg unit registered with Gatekeeper the call fails - appears to be routing issue. (Guy who configured the MCU said that call should connect to an attendant welcome prompt when I dial any of the Service Prefixes.
    First time I've configured H323 Gatekeeper. Does anybody now how this problem can be resolved?

    I had missed out route patterns on UCM (needs to have route pattern for service prefix, virtual conference room number followed by *** then password string for 1st user, then other users joining conference enter service prefix, virtual conference room number. Users joining conference get prompted for password (which was defined by 1st user.
    Problem resolved after I created the route patterns.

  • Using same MCU as a Media resource group in differents CM clusters

    Hi,
    I have 1 MCU 3545 (MCU and EMP) connected as a media resource group in a CCM6.1 cluster and it is working fine.
    The entire network has 4 CCM clusters and the problem that I have is that I'm not able to publish this media resource in the other 3 clusters .
    I doubt if this is possible, anyone has any idea how to do it?
    Thank you in advance,
    Bruno

    Guys,i found the answer for my question some how but don't know how to fix this.
    I have changed the setting of agent state after ring no answer to be always ready.
    So now if agent A didn't answer the call the call goes to agent B,and Uccx returns the state of agent A back to ready so the call reverts back to him and so on.
    If i used
    agent state after ring no answer:Not ready.
    Then the call goes to all agents but if all the agents didn't reply ,then the system plays a message :There is an erroe with the system please call back later.
    How to resolve this ? I need to make the agents always ready and call goes in the right order of Agents.

  • MCU 5320 Hardware Bug

    We have a Cisco 5320 MCU.  Recently after upgrading to version 4.5, we had an issue with the MCU performing an unexpected restart.  This problem began to reoccur.  After opening a TAC case, it was noted that this was related to a hardware bug CSCuc98311.  We received an RMA, and after about 2 weeks the problem started happening again.  Another TAC case was opened, it was referenced as the same issue.  This MCU was behaving the same.  Unexpected restarts.  We downgraded to 4.3, the original software we were on, and the problem still occurred. Below is the error fault reference in the log.  We will be receiving our 3rd MCU today.  I am very skeptical about this issue, and the stability of the MCU.  This has caused major interruptinos with multi-point video meetings.  Has anyone else experienced this problem or seen this before?
    (2,3) hv_panic: got processor error: PC 0x3_03a0, ICS/PL 0
    (2,3) L1_I_ERROR:            0_0000_0000
    (2,3) MEM_ERROR_CBOX_ADDR:   0x0058_272d
    (2,3) MEM_ERROR_CBOX_STATUS: 0x0001_0083
    (2,3) MEM_ERROR_MBOX_ADDR:   0_0000_0000
    (2,3) MEM_ERROR_MBOX_STATUS: 0_0000_0000
    (2,3) XDN_DEMUX_ERROR:       0_0000_0000
    (2,3) DIAG_TRACE_CTL:        0_0000_0000
    (2,3) mshim/0:
    This is tracked under a known bug CSCuc98311

    If you upgrade your MCU 5320 with the TelePresence Server migration software, this will turn the MCU into a TelePresence Server so all features and functionality will be that of a TelePresence Server and not an MCU.  See the Running TS Software on MCU 5300 Series install guide on how to convert your MCU to a TelePresence Server if you're interested.
    Here are two good discussions comparing the MCU and TelePresence Server platforms, one of them specifically about migrating from one to the other.
    what-difference-between-mcu-cisco-telepresence-server
    why-replace-mse-8510-mcu-44-telepresence-server-31
    The cisco_ts_3.1_1.98_for_mcu_5300 software is for migrating an MCU 5300 Series to a TelePresence Server.  While the cisco_ts8700_3.1_1.98 software is specifically for hardware that is already running TP Server software, such as the various TelePresence Servers models listed here, this includes MCUs that were migrated to run TP Server software such as the MCU 5300 Series and MCU MSE 8510.

  • Meeting Place 7.0 Audio Blade

    Hi - We are installing Meeting Place 7.0.2.14 with an IPVC3515-MCU for Audio/Video blade running software version 5.7.0.0.21.
    We can route and web to the IPVC directly, and all status for the MCU/EMP are fine.
    When we try to add the MCU under resource management through the Meeting Place Media Server Administration it authenticates and synchs the configuration, however, the MCU status remains as offline under Resource Management.  I have tried restarting the IPVC and Meeting Place services as well as deleting and adding the MCU - but it still appears as offline.
    Any assistance would be greatly appreciated.
    thanks
    Brian

    @Radim Mutina.
    Yes, like I said before, must read carefully the guidance (docwiki.cisco.com)
    If You don't read carefully guidance, it's look similar   only 1 word different
    I face this problem almost 3 days and I almost gave up, want to open TAC
    But, finally I found a needle in a stack of hay
    Thank You, for rate Me up

  • MeetingPlace Video Integration with 3515MCU problem

    Hi,
    I am trying to setup MeetingPlace Video Integration with a Cisco 3515 MCU and cannot get it to work. The eventlog for MeetingPlace Gateway is giving me errors about the initialization problems. A couple of such errors are:
    MPAgent (0x0150) Warning: Conference technology provider initialization failed (0x80040201). err=1
    MPVidSvc MPVideo 11:05:52-> CMcuController::processCmdRegAuthorize() Register as administrator failed. UNregistering....
    MPVidSvc MPVideo 11:06:02-> CMcuController::uninitialize() Uninitializing CMcuController.......
    Both MeetingPlace and MCU conferencing are working as they should, but I can't get the Video Integration working. From what I can tell by these messages, MeetingPlace cannot talk to the MCU to administer conferences. I have setup and configured a user on the MCU for MeetingPlace to use.
    Has anyone got MeetingPlace working with a 3515 MCU?
    Thanks,
    Richard.

    Richard,
    I'm having the same problem but with MCU 3540. This problem begin occur after I change the service number 70. My scenario is 2 sites. Each site have 1 cluster?s CCM, 1 MCU?s 3540 and the main site I have 1 MP system with 1 MP IP gateway and web conference in the same server. What the version of MP and MCU you are using ? I'm using MP V 5.3.333.0 and MCU V 4.2.10.

  • Telepresence Licenses, Servers and Personal Multiparty

    Dears,
    Our customer provide RFP with the following BOQ:
    LIC-AES-VTS-PMP-K9
    AES and HTTPS option for VTS
    2
    LIC-VTS-PMP-INTOP
    Order L-VTS-UPG-PAK for e-Delivery Virtual TS Interop Lic
    2
    LIC-VTS-PMP-K9
    Cisco VM TelePresence Server Release Key
    2
    LIC-VTS-PMP-PAK
    PAK for e-Delivery Virtual TS Lic
    1
    LIC-VTS-PMPUWL-1SL
    Cisco TelePresence Server Resource License
    8
    SW-VTS-V3.X-PMP-K9
    Software Image v3.X for Virtual TelePresence Server
    2
    VTS-PMP-K9
    Cisco VM Telepresence Server
    2
    LIC-TP-10X-ROOM
    Telepresence Room Based Endpoint Single or Multi-Screen
    15
    R-VMCNDTR-K9
    Virtual TelePresence Conductor-30 MCUs/2400 Call Sessions
    1
    SW-CNDTR-V2.X-K9
    Cisco TelePresence Conductor base software image v2.X
    1
    LIC-CNDTR-B30
    Conductor license support up to 30 conference bridges
    1
    LIC-CNDTR-C2400
    Conductor 2400 call sessions license
    1
    LIC-CNDTR-CL
    Conductor clustering support
    1
    LIC-CNDTR-K9
    Conductor License for Base Encrypted Software Image
    1
    LIC-SW-VMCNDTR-K9
    Software Release Key for Virtual Conductor
    1
    LIC-VMCNDTR-PAK
    PAK for virtual Conductor
    1
    CTI-5320-MCU-K9
    Cisco TelePresence MCU 5320 up to 40 SD ports
    2
    CON-ECDN-CTI5320M
    ESS WITH 8X5XNBD Telepresence MCU 5320 up to 40 SD ports
    2
    LIC-AESMCU53-K9
    AES and HTTPS option for MCU 5300 Series
    2
    LIC-5300-4PL
    1 Full HD / 2 HD / 4 SD ports on MCU 5300 Series
    4
    CON-ECDN-LIC5304P
    ESS WITH 8X5XNBD 1 Full HD/2 HD/4 SD ports on MCU5300
    4
    CTI-5300-CAB2MCU
    Cisco TelePresence MCU 5300 Series Stacking Cable
    2
    CON-ECDN-CTI53CAB
    ESS WITH 8X5XNBD MCU 5300 Series Stacking Cable
    2
    LIC-5320-MCU-K9
    License Key For MCU 5320 Software Image
    2
    SW-5300-MCU-K9
    Software Image For MCU 5300 Series Latest Version
    2
    I have some questions that is not clear for me regarding above BOM:
    1- In regard to Personal Multiparty Licenses that comes with CUWL PRO , It mentioned QTY 2 from each item ,does that mean 2 servers and 2 licenses will be installed for each TS or it is only one server and upload 2 licenses to it?
    2-"Cisco TelePresence Server Resource License" has QTY 8. is that mean 8 ports = 8 participant in one conference or what is that mean and what does it used for?
    3-In regard to conductor ordered with PMP, can it manage TS server(s) in concert with the MCUs that is ordered above or a new one should be purchased dedicated for the MCUs?
    4-For Conductor cluster ,Customer is asking for a cluster although the BOM has only 1 QTY. Does the cluster requires another SW license key to the second VM or just add it as Unified CM nodes for free ?.Noting that "LIC-CNDTR-CL" is mentioned in the BOM.
    5- In regards MCU 5320, "LIC-5300-4PL" mentioned as 4 QTY, is that mean it will be divided by 2 for each appliance after stacking them?
    6-does "LIC-5300-4PL" with 4 QTY means that I can have up to 16 participant in one conference or 2 concurrent conferences with 8 Participant ? or how it is calculated?
    I really appreciate your help to clear above points to get back to the customer with full understanding about the solution provided.
    Thanks in advance.

    Usually the questions like this would be directed to the one who put together the bill or materials for you.
    I've always had some issues reading BOMs, but if I'm reading and understanding it correct:
    You'll receive qty 2 TelePresence Servers, which is probably the 8-core virtual TP Server.
    The TelePresence Server Resource License is the screen licenses you install on the TelePresence Servers.  The 8-core virtual TP Server only requires 4 screen licenses each.  If I'm not mistaken, PMP must be setup with a max resolution of 720p.  So that would allow 2 participants per screen license.
    Looks like you're receiving a fully licenses Conductor, which can support all the MCUs and TP Servers.  For the TP Servers that are to be used with PMP, they must only be used for that, and nothing else.
    You'd have to purchase a second Conductor matching the one being purchased.
    If you stack them (also known as clustering), the total port count will be shared between the two servers.  Note, when stacked, the two servers are then seen as 1 single MCU.
    This depends on the quality you set the MCU to use for the media ports.  With qty 4 media ports, you can have the following number of participants:  up to 4 Full HD at 1080p, 8 HD at 720p, or 16 SD up to w448p.
    PMP data sheet, shows what you can do with the TP Servers being used and the conference restrictions.
    TelePresence Server data sheet, table 8 shows the screen license to participant ratio based on the expected video resolution.
    MCU 5300 Series data sheet, table 2 shows the media port licenses to participant ratio based on expected video resolution.

  • Telepresence implementation

    CTI-TMS-SW-K9
    Cisco TelePresence Management Suite   Includes 10 Systems=1 qty
    CTS-SX20-PHD12X-K9
    SX20 Quick Set HD  NPP  12xPHDCam  1 mic  remote cntrl =3 qty
    BE6K-ST-BDL-K9=
    Cisco BE6000 Medium Density Server  Export Restricted SW =2 qty
    CP-DX80-K9=
    Cisco DX80 =9 qty
    CTI-5320-MCU-K9
    Cisco TelePresence MCU 5320 up to 40 SD ports=1 qty
    suggest me how to design for above BOQ,by considering above boq i suspect i need to install Following VM in BE6K
    1) VCS-C&E
    2) TMS
    3)CUCM 
    Does VCS supports coresident? How to make a design for this BOQ?

    Duplicate thread - refer to https://supportforums.cisco.com/discussion/12302361/telepresence-implementation.

  • SX20 Floor Control

    Can someone please tell me where I can find the Floor Control options on a SX20 Codec?
    We use this quite regularly on our MXP95s but can't find it on the SX20 and are needing the end user to be able to set which remote endpoint (in a multi-site call) is shown in the prominent position.

    Hi folks,
    When connecting to a Cisco Telepresence MCU, SX20 is able to "take floor" by using DTMF sequence. You can send DTMF information to MCU and request floor, then SX20 will be shown in the proeminent position for all other participants.
    This same concept is applied to another endpoits as well, not only to SX20. For example, this is a print screen from Jabber client requesting floor via DTMF, take a look:
    That menu is shown when you press when you send * to MCU, so you can send number keys via DTMF to navigate int he menus. In this menu you can request floor, mute audio, change layout, see participants, increase border and so on.
    To enable this menu in the MCU, you need to configure the conference and set the parameter "Floor and chair control" to Allow floor.
    I hope this help.
    Regards
    Paulo Souza
    Please rate replies and mark question as "answered" if applicable.This is

  • Gk and video

    customer has polycom endstation and cisco video MCU. Can we use cisco voice gatekeeper, for example3845, to manage the call routing and bandwidth same as for regular voice call?

    Yes.

Maybe you are looking for