Cisco 3560 interface, not connected

Hello
I am in the process of determining available switch ports based on last usage and I came across the following that I don't understand.
Switch-3560G-1#sh int | I Last|Gig
GigabitEthernet0/7 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 0014.a98f.ba87 (bia 0014.a98f.ba87)
Last input never, output 21:56:52, output hang never
Last clearing of "show interface" counters never
The interface, notconnnect status, has a last output value is that is incrementing.
what could be causing this?

It means that the physical interface is down and the list time the switch saw any traffic (even though it's a one-way traffic) is almost 22 hours ago.

Similar Messages

Cisco Messaging Interface-Not Running

Hi All,
On the UCM 6.0 the Cisco Messaging Interface service is activated and when i check the status in 'control center feature services' it shows 'Not Running' and 'Activated'. If i start and refresh the page it again shows as 'Not Running'

Hi Vineet,
This interface is only used in CCM to Legacy VM integrations (via SMDI) if you are not setup that way this is why you are seeing this :)
Cisco Messaging Interface Service
The Cisco Messaging Interface allows you to connect a simplified message desk interface (SMDI)-compliant external **Third Party** voice-mail system with the Cisco CallManager. The CMI service provides the communication between the voice-mail system and Cisco CallManager. The SMDI defines a way for a phone system to provide a voice-mail system with the information needed to intelligently process incoming calls.
Genrally the Cisco Messaging Interface (CMI) is a Cisco CallManager service that should be run only on the publisher server. This service intercepts calls destined for voicemail and generates appropriate SMDI messages, which are then delivered to one of the server's Component Object Model (COM) ports.
From this doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a008037e2f3.html#wp1024396
Hope this helps!
Rob

Cisco CDA does not connect to domain controller

Hello,
I am trying to install the Cisco CDA (Context Directory Agent) to bridge the windows identity gap between Active Directory and Cisco IronPort WSA and eventually ASA.
I followed all the rules in the deployment instructions and I still cannot get this to connect. With a Domain Admin it always refuses the password. I then decided to try creating a new account as a domain user called CDAService and I followed the extra steps required to grant this user the proper access to the specific registry keys, DCOM and WMI, and they were added to the Event Log Readers group in AD. Though the error with this new user account is this:
exception-cause
org.jinterop.dcom.common.JIRuntimeException: The RPC server is unavailable. Please check if the COM server is up and running and that route to the COM Server is accessible (A simple "Ping" to the Server machine would do). Also please confirm if the Windows Firewall is not blocking DCOM access. [0x800706BA]
wmi-class
Win32_NTDomain
exception-message
The RPC server is unavailable. Please check if the COM server is up and running and that route to the COM Server is accessible (A simple "Ping" to the Server machine would do). Also please confirm if the Windows Firewall is not blocking DCOM access. [0x800706BA]
wmi-property
DomainName
dc-username
CDAService
I logged onto the console of our CDA virtual machine and I was able to ping the DC by name. I also used wbemtest utility on my workstation and used the CDAService account to connect to the \root\cim2 namespace and I was able to pull Win32_ComputerSystem attributes from WMI with that account. I am on the same subnet as the CDA appliance.
I double checked the Windows Server 2008 R2 firewall on this DC and inbound rules that have to do with WMI are ASync-In, DCOM-In WMI-In all set to allow inbound.
Any ideas how to get this to work? Its a Server 2008 R2 level domain.

Ok with the windows firewall off for the domain profile, it works. However we want the firewall on.
I ran this command just like the instructions said, but I guess there is something else the firewall is blocking?
netsh advfirewall firewall set rule group=”Windows Management Instrumentation (WMI)" new enable=yes
Here is the installation guide I am following:
http://www.cisco.com/c/en/us/td/docs/security/ibf/cda_10/Install_Config_guide/cda10/cda_install.html#81257

Cisco 1701 adsl not connecting??

Hey guys,
I'm using sdm to do a quick setup on my router i managed to setup using the quick wizard and i setup the pppoe connection but i don't think it's connecting because i am getting dns error when i try to browse. Am i missing a step??? Do i need to open something after i create the connection???
Where can i get a status to see what the problem is?

Ok guys this is driving me mad please tell me what i am missing.
I have reseted to default.
Access router via ip and used SDM software to configure the basics such as DHCP,pppoe and so on.
This is the print.
Building configuration...
Current configuration : 2469 bytes
! Last configuration change at 14:12:33 PCTimeZ Fri Jun 2 2006
! NVRAM config last updated at 14:12:42 PCTimeZ Fri Jun 2 2006
version 12.3
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname gateway
boot-start-marker
boot-end-marker
logging buffered 51200 debugging
logging console critical
enable secret xxxx
username root privilege 15 password xxxx
clock timezone PCTimeZone 0
no aaa new-model
ip subnet-zero
no ip source-route
ip dhcp excluded-address 10.10.10.1 10.10.10.19
ip dhcp excluded-address 10.10.10.41 10.10.10.254
ip dhcp pool sdm-pool1
network 10.10.10.0 255.255.255.0
default-router 10.10.10.254
ip tcp synwait-time 10
ip domain name domain.com
ip name-server 203.0.178.191
no ip bootp server
ip cef
ip audit notify log
ip audit po max-events 100
no ftp-server write-enable
no scripting tcl init
no scripting tcl encdir
no crypto isakmp enable
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0.1 point-to-point
description Adsl PPPoe
pvc 8/35
pppoe-client dial-pool-number 1
interface BRI0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
shutdown
interface FastEthernet0
description $FW_INSIDE$$ETH-LAN$
ip address 10.10.10.254 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
ip tcp adjust-mss 1452
speed auto
interface Dialer0
ip address negotiated
ip mtu 1452
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication pap callin
ppp pap sent-username [email protected] password xxxx
ip classless
ip http server
ip http authentication local
ip http secure-server
logging trap debugging
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
line con 0
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
scheduler allocate 4000 1000
scheduler interval 500
end
gateway#

Cisco Nexus v1000 not connecting to VMWare vCenter

I am trying to deploy Nexus 1000v, but there is a problem - no connection with vCenter. Pings are ok, all ip addresses and port numbers are valid. Console displays following error:
switch(config)#svs connection vc
remote ip address 10.10.10.200 port 5480
protocol vmware-vim
vmware dvs datacenter-name CORE
connect
ERROR: [VMWARE-VIM] Operation could not be completed due to connection failure. End of file or no input: Operation interrupted or timed out after 160s send or 160s receive delay
Thank you.

You should use port 80 instead of 5480 in your svs connection string. Port 5480 is the default port for the management of the vCSA.

Cisco 1100 AP not connecting

I have gotten into the AP
Used Express Setup to put in new Address, when clicking ok to save the browser can no longer connect.

what is wrong here, I have 3 of these units and they are all doing the same thing do they need to be re-imaged to use individually and if so where can I find the file

Ivette manzur : Interface errors problems on cisco 3560

Hello,
I have a problem on one of the interfaces on a cisco 3560 switch. In fact, I set up a monitoring network recently (cacti), and I have a significant number of errors on the interfaces. the problem is that when I do a sh interface I see no errors, and even by making a clear counters it does not solve my problem .. I also changed the wiring with cat 6 cables but nothing has changed ..
What are the main causes of errors on an interface of a switch? what should I do in this case?
Thank you for your help in advance
ivette manzur

Hello,
I've a e61i and I experience a similar problem. My phone work very well on WiFi network with no encryption as well as 64-bit wep.
At home I've 2 wireless routers, both encrypted at 128 bits, one with WEP and the other with WPA. On both of them I can correctly obtain an IP thru DHCP, but the traffic do not go thru.
By using IfInfo I think I discovered the reason of the problem (unless IfInfo is not working properly...) and it seems a bug related to the netmask, broadcast and gateway settings. The router is 192.168.15.1 and this is what I get:
1) DHCP case -- I get two IP adresses: the 169.254.x.x and the one assigned to the router. DNS is also set properly, but both gateway, broadcast and netmask are set to 0.0.0.0 for both IPs.
IP Addr: 169.254.162.106
Netmask: 0.0.0.0
Broadcast: 0.0.0.0
Gateway: 0.0.0.0
DNS1: 192.168.15.1
IP Addr: 192.168.15.100
Netmask: 0.0.0.0
Broadcast: 0.0.0.0
Gateway: 0.0.0.0
DNS1: 192.168.15.1
2) Static IP 192.168.15.64, netmask set to 255.255.255.0 and gateway and DNS set to 192.168.15.1. The 169.254.x.x disappears and I get only one IP which is set to:
IP Addr: 192.168.15.64
Netmask: 0.0.0.0
Broadcast:192.168.15.255
Gateway: 192.168.15.1
DNS1: 192.168.15.1
So in conclusion, it seems that with 128bit encryption, in the DHCP case gateway, broadcast and netmask are not assigned correctly! While in the Static IP case the netmask is still not assigned correctly!!!
Hope this can help...
--AP

Service-policy output not working in Cisco 3560 switch

We got some Cisco catalyst 3560 that we want to control the bandwidth
on the ports. Can this be done, and how do i do it?
Ive got 3550s that can do policy-map with the interface command;
service-policy output(and input) <policyname>
But 3560 only seems to handle service-policy input.
If i try to configure output, it says the following:
SW(config-if)#service-policy output 4mbit-out
police command is not supported for this interface
Configuration failed!
Warning: Assigning a policy map to the output side of an interface not
supported
Any workarounds or new ways to accomplish bandwith-control on a 3560 ?
regards,
Rajib

The 3560 & 3750 (& 2960) don't support egress policy-maps. They do however support queueing so it is possible to achieve similar results by applying an ingress policer to your user ports to classify (& police?) the traffic, at the egress port you can then queue the traffic based on it's DSCP or CoS value that it was classified with (same as 3550).
It is also possible to restrict the bandwidth in use at an egress port with the interface command 'srr-queue bandwidth limit <10-90>' where 10-90 represents a percentage of the links bandwidth. For example if you want to restrict a 100Mbps port to 10Mbps you would use the command 'srr-queue bandwidth limit 10'
HTH
Andy

Openswan client/Cisco RV220W not connecting

I am attempting to connect a laptop with an openswan client (Openswan IPsec U2.6.28/K3.0.0-12-generic) with my Cisco RV220W. My connection fails, and the VPN status log shows the following:
2011-12-06 15:04:59: [rv220w][IKE] INFO: Configuration found for 108.58.YY.YY[500].
2011-12-06 15:04:59: [rv220w][IKE] INFO: Received request for new phase 1 negotiation: 108.58.XX.XX[500]<=>108.58.YY.YY[500]
2011-12-06 15:04:59: [rv220w][IKE] INFO: Beginning Identity Protection mode.
2011-12-06 15:04:59: [rv220w][IKE] INFO: Received unknown Vendor ID
2011-12-06 15:04:59: [rv220w][IKE] INFO: Received Vendor ID: DPD
2011-12-06 15:04:59: [rv220w][IKE] ERROR: Ignore information because the message has no hash payload.
2011-12-06 15:05:09: [rv220w][IKE] ERROR: Ignore information because the message has no hash payload.
2011-12-06 15:05:11: [rv220w][IKE] ERROR: Phase 1 negotiation failed due to time up for 108.58.YY.YY[500]. c2e6f14d16bef607:02dbd105dcc0b299
2011-12-06 15:05:19: [rv220w][IKE] ERROR: Ignore information because the message has no hash payload.
2011-12-06 15:05:29: [rv220w][IKE] ERROR: Ignore information because the message has no hash payload.
2011-12-06 15:05:39: [rv220w][IKE] ERROR: Ignore information because the message has no hash payload.
2011-12-06 15:05:49: [rv220w][IKE] ERROR: Ignore information because the message has no hash payload.
2011-12-06 15:05:59: [rv220w][IKE] ERROR: Phase 1 negotiation failed due to time up for 108.58.YY.YY[500]. 5646ff766f579fb0:b221f323a56ba913
My configuration on the RV220W is as follows:
VPN Policy:
Auto Policy
Remote endpoint is an IP address with 108.58.YY.YY
Local traffic is a subnet
Remote traffic is a single IP (same as above)
Encryption/hash settings are: 3DES, SHA1, no PFS key group, SA lifetime of 3600
IKE Policy:
Responder
Main mode
Local and Remote use explicit IP addresses
3des,sha1,pre-shared key,DH group 2,lifetime of 28800,no dead peer detection,no xauth
On the client, I have the following openswan configuration:
# /etc/ipsec.conf - Openswan IPsec configuration file
# This file: /usr/share/doc/openswan/ipsec.
conf-sample
# Manual:     ipsec.conf.5
version    2.0    # conforms to second version of ipsec.conf specification
# basic configuration
config setup
    # Do not set debug options to debug configuration issues!
    # plutodebug / klipsdebug = "all", "none" or a combation from below:
    # "raw crypt parsing emitting control klips pfkey natt x509 dpd private"
     # eg:
    # plutodebug="control parsing"
    # enable to get logs per-peer
    # plutoopts="--perpeerlog"
    # Again: only enable plutodebug or klipsdebug when asked by a developer
    # NAT-TRAVERSAL support, see README.NAT-Traversal
    nat_traversal=no
    # exclude networks used on server side by adding %v4:!a.b.c.0/24
    virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12
     # OE is now off by default. Uncomment and change to on, to enable.
    oe=off
    # which IPsec stack to use. auto will try netkey, then klips then mast
    interfaces=%defaultroute
    plutodebug=all
    protostack=netkey
# Add connections here
conn L2TP-PSK
     # Use a pre-shared key.
      # Connection type _must_ be transport mode
     authby=secret
     keyingtries=3
     type=transport
     # "left" is the local linux machine
     left=%defaultroute
     leftprotoport=17/1701
      # "right" is the remote server
     right=108.58.XX.XX
     rightprotoport=17/1701
     # Do not install on startup
     auto=add
     # SA settings
      ike=3des-sha1-modp1024
     esp=3des-sha1
     keyexchange=ike
     pfs=no
I would appreciate any insights into what might be going wrong here.

Were you able to find a solution to your issue.   I am having a Similar issue connecting to a ASA 5510.
Thanks!

Can not connect computer to Cisco Connect -EA3500

Can not connect computer to Cisco Connect -.Receive error msg 82BD0305. Reset to EA3500 to default and reinstalled software.

Reading the manual it says the username is blank, password 'admin'.

MBP upgraded to Yosemite and now will not connect to Internet using a Cisco router

I Upgraded my MBP mid 2010 to Yosemite and now it will not connect to Internet using a system that involves typing in my user name and password in an auto pop up window provided by Cisco security systems. Before, using Mavericks, it worked perfectly: boot up MBP and the Cisco pop up auto loaded. Typed it my password and hey presto, connected to Internet. Now, zilch. There is nothing wrong with the Cisco cos my iPad connects ok, as do both my iPhone's.
the problem is with Yosemite therefore. Please help. I tried all the usual diags, etc to no avail.
Message was edited by: AWAC

Sounds like there could be some kind of compatibility issue between ICS and this Bluetooth device of yours. Is there any compatibility info from the manufacturer about which Android versions that's being supported?
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

No interface driver connected - Function not performed

Can some one please help me. I am a new user of Oracle, and I am trying to logon using SQl plus 8.0. (system/manager @ODBC:POLITE. But I get an error message saying "No interface driver connected - Function not performed" Where on the machine is the interface driver usually stored. I also have SQL plus 8.0 on the same machine, and it works when I log on using scott/tiger.
null

<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Uche Ubani ([email protected]):
Can some one please help me. I am a new user of Oracle, and I am trying to logon using SQl plus 8.0. (system/manager @ODBC:POLITE. But I get an error message saying "No interface driver connected - Function not performed" Where on the machine is the interface driver usually stored. I also have SQL plus 3.3 on the same machine, and it works when I log on using scott/tiger.<HR></BLOCKQUOTE>
null

Could not connect to wicd's D-Bus interface. Check the wicd log for er

Having issues getting wireless to work on Acer V3 551. Wired works great. I'm new to Arch from Ubuntu, so please be nice to me
On startup, I get two error dialog boxes:
#1: Could not connect to wicd's D-Bus interface. Check the wicd log for error messages.
#2: The wicd daemon has shut down. The UI will not function properly until it is restarted.
Network info:
23:01:00.0 Ethernet controller: Qualcomm Atheros AR8151 v2.0 Gigabit Ethernet (rev c0)
24:02:00.0 Network controller: Atheros Communications Inc. AR9462 Wireless Network Adapter (rev 01)
wicd-curses terminal output:
wicd-curses
Can't connect to the daemon, trying to start it automatically...
Traceback (most recent call last):
File "/usr/share/wicd/curses/wicd-curses.py", line 1043, in <module>
setup_dbus()
File "/usr/share/wicd/curses/wicd-curses.py", line 1031, in setup_dbus
dbus_ifaces = dbusmanager.get_dbus_ifaces()
File "/usr/lib/python2.7/site-packages/wicd/dbusmanager.py", line 36, in get_dbus_ifaces
return DBUS_MANAGER.get_dbus_ifaces()
File "/usr/lib/python2.7/site-packages/wicd/dbusmanager.py", line 62, in get_dbus_ifaces
if not self._dbus_ifaces: connect_to_dbus()
File "/usr/lib/python2.7/site-packages/wicd/dbusmanager.py", line 48, in connect_to_dbus
return DBUS_MANAGER.connect_to_dbus()
File "/usr/lib/python2.7/site-packages/wicd/dbusmanager.py", line 79, in connect_to_dbus
proxy_obj = self._bus.get_object("org.wicd.daemon", '/org/wicd/daemon')
File "/usr/lib/python2.7/site-packages/dbus/bus.py", line 241, in get_object
follow_name_owner_changes=follow_name_owner_changes)
File "/usr/lib/python2.7/site-packages/dbus/proxies.py", line 248, in __init__
self._named_service = conn.activate_name_owner(bus_name)
File "/usr/lib/python2.7/site-packages/dbus/bus.py", line 180, in activate_name_owner
self.start_service_by_name(bus_name)
File "/usr/lib/python2.7/site-packages/dbus/bus.py", line 278, in start_service_by_name
'su', (bus_name, flags)))
File "/usr/lib/python2.7/site-packages/dbus/connection.py", line 651, in call_blocking
message, timeout)
dbus.exceptions.DBusException: org.freedesktop.systemd1.LoadFailed: Unit dbus-org.wicd.daemon.service failed to load: No such file or directory. See system logs and 'systemctl status dbus-org.wicd.daemon.service' for details.
systemctl status dbus-org.wicd.daemon.service terminal output:
dbus-org.wicd.daemon.service
Loaded: error (Reason: No such file or directory)
Active: inactive (dead)
I've tried:
- beginners install suggestions
- arch wicd suggestions
- unin/re-installing wicd
- google research to no avail

Apologies. First post to the board - will keep post within bracket tags. Sorry for being such a noob.
Input
$ systemctl status wicd.service
Output
wicd.service - Wicd a wireless and wired network manager for Linux
Loaded: loaded (/usr/lib/systemd/system/wicd.service; disabled)
Active: failed (Result: exit-code) since Wed 2013-05-01...
Process: 972 ExecStart=/usr/sbin/wicd --no-daemon (code=exited, status=1/FAILURE)
Starting Wicd a wireless and wired network manager for Linux
It seems like the daemon is already running
If it is not, please remove /var/run/wicd/wicd.pid and try again.
wicd.service: main process exited, code=exited, status=1/FAILURE
Failed to start Wicd a wireless and wired network manager for linux.
MESSAGE=Unit wicd.service entered a failed state.
Any thoughts?
Last edited by roastymctoasty (2013-05-01 15:58:17)

This an IPOD I bought used. Everything else works fine. It syncs to my computer and plays my music but will not connect to the USB interface in my car. My wife's IPOD, which seems to be identical, works fine. Any ideas?

This an IPOD I bought used. Everything else works fine. It syncs to my computer and plays my music but will not connect to the USB interface in my car. My wife's IPOD, which seems to be identical, works fine. I should say it connects but then immediately disconnects. Any ideas?

Then my last suggestion is to Reset it, while connected to the BMW Audio.
Toggle the Hold switch, make sure you dont see the red mark when you do the next step
Reset the iPod -> Press Menu and Center button simultaneously for about 10 secs or till the Apple Logo comes ON
Then release the buttons
Select your preferred language.
Here is the Apple support Article on the 5Rs
http://www.apple.com/support/ipod/five_rs/classic/
Good Luck!

Cisco ASR - How to connect an OTV internal interface to a FabricPath domain

Scenario - migrate servers while maintaining their existing IP address from data centre 1 to data centre 2 with minimal downtime. Diagram attached.
I'm planning on using a Cisco ASR1001-X with AES license at DC1 and DC2 and configuring the routers with OTV to extend 10 x VLANs between the data centres. The join interface would connect directly to the WAN circuit NTU and the Internal Interface would connect to the switch and be configured as a service instance with 10 VLANs tagged using dot1q. The problem is that DC1 switch infrastructure is using Cisco Nexus 56xx configured with FabricPath. I can't find any information that suggests that i can patch the Cisco ASR router's internal interface directly into a FabricPath switchport or what the configuration would be.
Older OTV documentation refers to Nexus 7000 and OTV stating the following: "Because OTV encapsulation is done on M-series modules, OTV cannot read FabricPath packets. Because of this restriction, terminating FabricPath and reverting to Classical Ethernet where the OTV VDC resides is necessary."
Is this true for the Cisco ASR also? The only workaround i can think of is to install a cheap catalyst switch connected to the FabricPath domain and re-introduce spanning-tree at the edge but this seems backwards to me. Any help or suggestions appreciated? Thanks

Thanks Minh,
So it is possible to have switchports configured as routed, fabricpath and trunk/access in a fabricpath configuration? Do i need to add any spanning-tree pseudo or priority configuration?
Sample configs:
#ASR
interface GigabitEthernet0/0/1
no ip address
service instance 1 ethernet
  encapsulation dot1q 1
  bridge-domain 1
service instance 2 ethernet
  encapsulation dot1q 2
  bridge-domain 2
service instance 3 ethernet
  encapsulation dot1q 3
  bridge-domain 3
#Nexus 56xx
interface e1/5
switchport mode trunk
switchport trunk allow vlan 1,2,3

Cisco 3560 interface, not connected

Similar Messages

Maybe you are looking for