Cisco 3560 series device manager

Hi all, Can anyone tell me why my new switches arent showing up the switch health information on them from http, I can see a fan spinning around and the temp, but the bandwidth used etc isnt showing anything

hi
thats correct, I am not recieving anything on the stats no matter what the useage on the switch? any ideas ?

Similar Messages

Cisco 300 Series device packages

Know someone when will be available 300 series packages for CiscoWorks LMS 4 ?

Hi,
Kindly share the SysObjectID for the device.
Here are the list of device supported in LMS 4.0
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.0/device_support/table/lms40sdt.html
Thanks,
Gaganjeet

Cisco 3560 cg (change management vlan)

Good Day guys ,
i've purchased some of the new 3560 cg catalyst switches. Am looking for some guidance/assistance into the procedure to change the default (vlan 1) to my management vlan (x). I have been successful in the addition of all my vlans inclusive of the management to the switch using the following command "switchport access vlan x" via the command line.
Currently I have CE 500's in my environment which allows you to change the management vlan from the GUI. Any recommendations/ assistance as to how this is now done on the newer model switches via command line or GUI would be greatly appreciated.
Regards,
Christian.

conf t
vlan <BLAH>
name Management
exit
default interface vlan 1
interface vlan 1
shutdown
interface vlan <BLAH>
description YIPEE
ip address 1.2.3.4 255.255.255.0
no shutdown

Access-list in Cisco 3560 Series Switch

Guys,
I will be implementing access-lists in 3560 switch. Hope you can help me with the configuration. I'm planning to block all ports by default and only allow ports that the user need to access. The ports will be as follows, tcp - 80, 81, 8080, 25, 110, 143. For udp - 23 and port used by IP Phone.
Hope you can help me guys.
Thanks,
John

and then dont forget to call this access-list on the interface or vlan you want to apply it.
You can use a number for the ACL > 100 or a name as indicated earlier.
If you go with just a number :
access-list 100 permit tcp any any eq 80 81 ...
access-list 100 permit udp any any eq 23
int g1/0/1
ip access-group NAME in
OR
ip access-group 100 in
As for example :
NMS-3750-A(config-if)#ip acc
NMS-3750-A(config-if)#ip access-group ?
<1-199> IP access list (standard or extended)
<1300-2699> IP expanded access list (standard or extended)
WORD Access-list name

Does Cisco Fabric/Device Manager 5.0(4d) run under VM?

I'd like to upgrade the OS on our W2k3 to W2K8 64-bit via virtual machine. First, is it possible to run Cisco Fabric and Device Manager under VM 2K8 64-bit? Has there been any issues reported running these tools, on VM?
Thanks

Hello Jayson,
Yes, Cisco Fabric Manager and Nevice Managercan run on W2k3 to W2K8 64-bit VM
http://www.cisco.com/en/US/partner/docs/switches/datacenter/mds9000/sw/5_0/release/notes/fm/fm_rel_notes_504d.html
VMs:
VMs that run any qualified or supported operating system version can run Cisco Fabric Manager.
Thanks

Mds95xx device manager for os 5.2.8a and above

Hi
I am looking into Cisco site for Device manager download for os 5.2.8a or above.
Someone can help me?
Many thx
Walter

Hi Walter,
There are two ways to get Device Manager.
(1)Install DCNM and DM will also be installed.
(2)Point your browser at the IP address of the switch and download it from there. Then run the "jxpiinstall.exe" file to install DM. However, to install it from here, you must have Java 1.5 and 1.6 or you will just get a "Certificate Revoked" message.
Best regards,
Jim

Quick Question about Cisco 3560 and the Web Device Manager

Alright, I have a quick question that I am curious about but I haven't found any information
about it.
When I log into my Cisco 3560 using the web portal to get to the Device Manager. Below the
diagram of the switch, then under the Dashboard there is section called Switch
Health, Port Utilization.
Under the Switch Health there is Bandwidth Used, Packet Error. Those two options just sit
at zero and do not move. The Port tilization graph is also sitting at zero.
Is there a way to make them functional?

Anyone notice performance increase or decrease of their HD when using the nVidia IDE SW drivers? particularly with a 74GB Raptor? I've also heard of burner issues when installing the IDE SW but have not used my burner yet.

Embeded Event Manager on cisco 3560 switch

Can someone help me please? I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. For some reason this configuration is not good and I can't tell why. I already try to debug this with debug event manager action mail but didn't see any output .
ip sla 11
icmp-echo ip address
frequency 20
ip sla schedule 11 life forever start-time now
event manager applet device-TEST
event snmp oid 1.3.6.1.4.1.9.9.42.1.2.9.1.6.11 get-type exact entry-op lt entry-val "2" poll-interval 20
trigger occurs 5 period 120
action 02.0 mail server "ip address" to "[email protected]" from "[email protected]" subject "device is down"

The mail part looks good, I'm not sure you are hitting the trigger right.
Why not do a track on the ip sla instead of the snmp stuff?
Here's a good example of that.
https://learningnetwork.cisco.com/blogs/network-sheriff/2009/06/19/writing-your-first-eem-applet

Unable to open 2 9509 switches at the same time in Cisco Device Manager

Dear Friends,
There are a pair of MDS 9509 switches whose management addresses are 172.16.2.197 and 172.16.2.198.
When we try to manage these Devices through Cisco device manager, the first device opens up without any problem, but when the second 9509 is opened in Cisco Device Manager, it fails giving the following error message:
"Open udp transport failed: Address already in use: Cannot bind"
To get around this issue, if we close the first interface to the 9509 switch, then we are able to open up the second 9509 in Device Manager.
We have this problem only in Cisco device manager. If we open one switch in Cisco device manager and the other switch in Cisco Fabric Manager, it works.
Also, we can telnet to both the devices successfully at a time.
The device manager in use is 4.1.
Please find enclosed the sh version outputs for your kind reference.
Can you please help me understand the cause of this issue?
Thanks a lot
Gautam

Is it always the same MDS that fails to open, or can you open either one first, and then the second one poses the problem (no matter which one is second)?
Can you try from a second work station and see if you can open DM to both switched at the same time? I suspect the address it is complaining about is the local workstation IP, not the MDS IP.
If you open the FM map, then you click on the MDS ICONs, can you open DM to both MDS?
- Mike

Ask the Expert: C-Series Integration with Cisco Unified Computing System Manager

Welcome to the Cisco Support Community Ask the Expert conversation. This conversation is an opportunity to learn and ask questions about Cisco C-Series Integration with Cisco Unified Computing System® Manager (Cisco UCS® Manager) with Cisco experts Vishal Mehta and Manuel Velasco.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (Cisco IMC). When a C-Series rack-mount server is integrated with Cisco UCS Manager, the IMC no longer manages the server. Instead you will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager command-line interface (CLI).
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management. The following are the connectivity modes:
Dual-wire management (shared LAN On Motherboard [LOM]): Shared LOM ports on the rack server are used exclusively for carrying management traffic.A separate cable connected to one of the ports on the Payment Card Industry Express (PCIe) card carries the data traffic.
SingleConnect (Sideband): Using Network Controller Sideband Interface (NC-SI), the Cisco UCS Virtual Interface Card 1225 (VIC1225) connects one cable that can carry both data and management traffic.
Direct Connect Mode: Cisco UCS Manager Version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
Vishal Mehta is a customer support engineer for Cisco’s Data Center Server Virtualization Technical Assistance Center (TAC) team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco Nexus® 5000, Cisco UCS, Cisco Nexus 1000V, and virtualization. He presented at Cisco Live in Orlando 2013 and will present at Cisco Live Milan 2014 (BRKCOM-3003, BRKDCT-3444, and LABDCT-2333). He holds a master’s degree from Rutgers University in electrical and computer engineering and has CCIE® certification (number 37139) in routing and switching and service provider.
Manuel Velasco is a customer support engineer for Cisco’s Data Center Server Virtualization TAC team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco UCS, Cisco Nexus 1000V, and virtualization. Manuel holds a master’s degree in electrical engineering from California Polytechnic State University (Cal Poly) and CCNA® and VMware VCP certifications. Remember to use the rating system to let Vishal and Manuel know if you have received an adequate response.
Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center, under subcommunity, Unified Computing, shortly after the event. This event lasts through May 23, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Sebastian,
The different modes of connecting C-Series with UCSM come into play depending on the type of infrastructure you already have along with C-Series and NIC model.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (CIMC) .
Powerful features provided by Cisco UCS Manager can be leveraged to manage C-Series server by integrating C-Series Rack-Mount Server with UCSM.
This not only gives you rich-feature set but also one management plane to operate UCS-B Series Chassis and UCS-C Series Rack Server.
You will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager CLI.
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management.
The following are the connectivity modes:
• Dual-wire Management (Shared LOM):
Shared LAN on Motherboard (LOM) ports on the rack server are used exclusively for carrying management traffic. A separate cable connected to one of the ports on the PCIe card carries the data traffic. Using two separate cables for managing data traffic and management traffic is also referred to as dual-wire management.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0100.html
This mode is recommended when you have C-Server which does not have or cannot support VIC 1225 card (such C-200 server)
• SingleConnect (Sideband):
Using Network Controller Sideband Interface (NC-SI), Cisco UCS VIC1225 Virtual Interface Card (VIC) connects one cable that can carry both data traffic and management traffic.
This feature is referred to as SingleConnect.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_011.html
This most recommended Integration model when using FEX and VIC 1225 card
• Direct Connect Mode:
Cisco UCS Manager release version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
This mode will eliminate the need for FEX module as Servers are directly plugged into the base ports of Fabric Interconnect
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0110.html
Please let us know if you need more information. Thank you!
Thanks,
Vishal

Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture

My Cisco Prime Infrastructure ver. 1.2.1.12
Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture.
Please let me know how to access or enable the feature.
Thanks,
Tek

This is by no means a full solution, but deleting and re-adding only takes a few minutes if you use the "Export Device" and "Bulk Import" features from the Device Work Center. You can export the desired devices to a CSV file, delete them, then import from the CSV.
Of course, you might lose historical data when deleting the devices, but I'm guessing that's not as relevant since the devices themselves have been replaced by different hardware.

Windows 7 64-bit Cisco Fabric/Device Manager Installer

Does anyone know if there is Cisco Device Manager Installer compatible with Windows 7 (64-bit)? I'm trying to install Device Manager onto my Windows 7 PC. this may happen on my Fabricv Manager Installer, as well. Any help would be appreciated.
Thanks

Senthil, Horacio,
I would not recommend using a 8.5(x) client against a 8.0(x) server (the OP suggests UCCE 8.0 is used). Even though they _should_ be compatible, they usually are not.
Upgrading the server side to 8.5 is the way to go IMHO.
G.

Cisco PIX Device Manager Version 3.0(2)

Hi
I have a PIX 515E:
Cisco PIX Firewall Version 6.3(4)
Cisco PIX Device Manager Version 3.0(2)
Compiled on Fri 02-Jul-04 00:07 by morlee
CCP-Firewall001 up 2 years 65 days
Hardware: PIX-515E, 32 MB RAM, CPU Pentium II 433 MHz
Flash E28F128J3 @ 0x300, 16MB
BIOS Flash AM29F400B @ 0xfffd8000, 32KB
0: ethernet0: address is 0012.80be.450d, irq 10
1: ethernet1: address is 0012.80be.450e, irq 11
Licensed Features:
Failover: Disabled
VPN-DES: Enabled
VPN-3DES-AES: Disabled
Maximum Physical Interfaces: 3
Maximum Interfaces: 5
Cut-through Proxy: Enabled
Guards: Enabled
URL-filtering: Enabled
Inside Hosts: Unlimited
<--- More ---> Throughput: Unlimited
IKE peers: Unlimited
This PIX has a Restricted (R) license.
Serial Number: 808480455 (0x30306ec7)
Running Activation Key: 0xac646fed 0xf8b86795 0xc3951ec2 0xb32aed09
It's operate with Java plug in 1.4.1 y I have a PC with IE 7 and Plug in 1.6.0 y doesn't download the PDM.
Are there a solution for it?

Try Disable Java on Internet Options. This issue oculd be releated to Java version also.

Cisco View Device Manager

Hi,
is there anybody who can tell me how to bring the Cisco View Device manager for 6500er up? I've installed the CVDM V.1.1 in the bootflash of my 6500er, IOS version is 12.2(18)SXF4 enterprise services. Installed java on the client is v.1.4.2_06. After launching the CVDM whithout proxy settings the windows starts gathering information, after a few seconds it stops with an error "java.lang.NullPointerException". This failure appeared with Mozilla 2.0.0.8 and IE 6.0, on the 6500er all vty lines are idle. Is anybody here who can help to solve the problem?

Here the text from the readme file; try to get the zip-file via the Bug-Id:
09-December-2005
This patch provides fix for the following bug:
CSCsc10956 - CVDM 1.1 does not work with 12.2(18)SXF
SUPPORTED IOS VERSION:
12.2(18)SXF
SIZE:
5,593,057 Bytes
DOWNLOADING AND MOVING FILES TO TFTP SERVER:
cvdm-c6500-1.1-CSCsc10956.zip contains the following two files
* cvdm-c6500-1.1.tar and
* cvdm-c6500-1.1_K9.tar (for Cisco IOS Cryptographic software)
Unzip cvdm-c6500-1.1-CSCsc10956.zip and copy one of the tar files to a TFTP server
Make sure to enter filenames exactly as they appear; (filenames are case-sensitive).
TRANSFERRING FILES TO YOUR SWITCH:
Step 1 : Access the switch CLI using a Telnet connection or the console port.
Step 2 : Transfer the files from the TFTP server to the bootflash of the switch. Issue
the following command:
# archive tar /xtract tftp:// / bootflash:
where is the filename of the CVDM-C6500 tar file you want to install
and is the IP address of the TFTP server. Make sure to enter filenames
exactly as they appear (filenames are case-sensitive). Make sure you are not in
configuration mode when issuing the archive command.
Step 3 : If you are not in configuration mode, issue the following command:
# configure terminal
Step 4 : Set HTTP server and path. For example:
# ip http path bootflash:
Please refer cvdm-c6500-1_1_readme.pdf in http://www.cisco.com/cgi-bin/tablebuild.pl/cvdm-6k for
further details on CVDM-C6500.

Can Cisco Device Manager Support ACS Authentication?

Background:
My company has approximately 500+ devices all across the country (mainly 2801's, 2924's, 2950's, and 2960's) and approx 3 people that have a real idea of how to configure the devices, and 2 or 3 that have a general clue about how to do it. I am in the process of moving all of these devices to use ACS authentication for signing into the device. While I am doing this I am establishing a strong password for the secret password to provide as a backup.
Problem:
My supervisor would like the cisco device manager to be available to the people that don't have the in depth cli experience. However in my testing, it will only accept the strong password for its authentication, and does not try the ACS server for authentication. Is this possible?

Hi,
Actually, there is a difference as from where the authentication is picked from for HTTP authentication,
With HTTP v1 server, same method list is picked, that is used by VTY lines.
With HTTP v1.1 server, but before the integration of fix for bug CSCeb82510, the method list defined for console is checked.
After the fix of the above mentioned bug, we have some different sent of commands that we can use.
I would suggest you to give this a try,
aaa authentication login CONSOLEandHTTP tacacs+ local
aaa authorization exec CONSOLEandHTTP if-authenticated
ip http authentication aaa
line con 0
login authentication CONSOLEandHTTP
authorization exec CONSOLEandHTTP
For detail please refer,
http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a008069bdc5.shtml
Regards,
Prem

Cisco 3560 series device manager

Similar Messages

Maybe you are looking for