Cisco 3617 to ONS 15454 E100T CAT5 Cabling

In an ethernet connection from a Cisco 7613 router ethernet port through a patch panel to an ONS 15454 E100T interface card, is a crossover cable required and if so, does convention dictate the crossover cable be installed on the router side of the patch panel or on the ONS side?

Yes, it should be a crossover cable.
I don't think there's a specific convention for placement, whichever side is best for you. However, it should be well-labeled (flags, tage, blinking lights, whatever) as a crossover cable to prevent it's replacement with a standard cable during troubleshooting.
Good Luck
Scott

Similar Messages

  • ONS 15454 Password Recovery Cable

    Does anyone know the part number for the password recovery cable needed to connect a laptop to the TCC card to used to reset the password to Cisco defaults?  I have attached the cisco PDF which explains the connection of this cable.
    Thanks

    The part number is 15454-EPC=
    In the past, you couldn't order this item but had to call Cisco TAC and request one.
    Hope this helps.

  • ONS 15454 Craft interface to a Cisco 2511 Terminal Server

    Does anybody have pinout of wiring ONS 15454 craft interface to a Cisco 2511 terminal server? I tried many combinations but nothing seem to work.
    2511 has octal cable with RJ-45 connector. I used an rj-45 coupler to connect a wire wrapped RJ-45 cable to craft interface.
    Thanks,

    Pin Field
    Contact
    Function
    Craft
    A1
    Receive
    A2
    Transmit
    A3
    Ground
    A4
    DTR

  • Ethernet over OC-3 between a E100T-12 (ONS 15454) and a remote device

    What CISCO device will accept an OC-3 (non-ATM) interface and establish an Ethernet connection with a E100T-12 card in a CISCO ONS 15454?

    You could map an Ethernet circuit from an ONS 15327 over an OC3 and terminate it on E100T-12 on the 15454. Hope that helps.

  • Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?

    Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?
    Flow would be
    Cable modem---->cisco e2000 wifi router (This is broadcasting wifi but not strong enough)---->4 port hub ---->airport express (to extend the wifi in another part of house)
    thanks!

    Yes, you can do this as you stated. In essence you will want to configure both routers for roaming network. Please check out the following Apple Support article that describes this type of network. Although this article uses two or more AirPorts, it can be done with just about any manufacturer's router.

  • Cisco ONS 15454 SONET MSPP

    I am doing a school research project in which I am setting up an OC-192 ring for a company (contract work through AT&T). I have chosen to use the Cisco ONS 15454 SONET MSPP as my platform. The company currently has locations in Chicago and Philadelphia and connects them through an OC-12C ATM connection and they are looking to add 2 gigabit ethernet connections.
    My question is what cards and parts will I need for the Cisco ONS 15454 SONET MSPP, and how much will everything cost? I have been searching the internet for components and prices and I have found it extremely difficult to find any information. Any help or tips anyone can offer would be greatly appreciated.

    Nick,
    You can find the HW specifications for various ethernet cards for the 15454 at the following location.
    http://www.cisco.com/en/US/docs/optical/15000r9_1/15454/sdh/reference/guide/454e91_ethernetcards.htmlhttp://www.cisco.com/en/US/docs/optical/15000r9_1/15454/sdh/reference/guide/454e91_refer.html
    To make sense of it all, you need to contact a Cisco sales/account represetative to help you analyze your needs, design your network and put together a price list for the appropriate cards.
    If you are interested, I can get someone from the sales/account team to contact you.   Please contact me directly with your contact information and geographic location so I can find the appropriate sales/account to help you.  Please do not post your personal information directly to the forum.
    [email protected]
    -Steve Noyes

  • ONS 15454 Back Plane DS1 Cable Question...

    Do the DS1 connectors on the back plane of the ONS 15454 mate with screw down AMP Champ connectors or with Bail Lock AMP Champ connectors? The documentation seems to be ambiguous. The part number listed for the connector is a Bail Lock type connector, but the drawings and the last paragraph in section 1.11.2 of the Hardware Installation document suggest it is a Screw Down connector.

    If you don't get a suitable response to your post from another forum userm you may wish to review our resources at the online http://www.cisco.com/. You may also contact our product information line at 1-800-553-NETS or a Cisco Systems Engineer at your local Cisco office or reseller. To locate your local Cisco representative, visit http://www.cisco.com/warp/public/687/Directory.shtml
    If anyone else in the forum has some experience with this issue, please reply to this thread.
    Thank you for posting.

  • Cisco ONS 15454 SDH

    Hi,
    i have 3 sites connecting together with SDH 15454 site A-B with STM-1 and from site B-C STM-16,i want to Aggregated hand-off E1's from Site A-C so site B will be trasparet site for this link.
    to be source of link on site A and Drop on site C.
    any help to achive this.
    there is already cricte between site B-C.

    You will need to verify that the cross-connect card in the ONS 15454 (sites B & C) have VC-12 grooming capabilities (XC-VXL and CX-VXC will support VC-12 grooming).
    The ONS is designed to groom lower rate signals to higher rate speed lines. Thus, you should be able to aggregate the E1s from the ISPs STM1 with the E1s from Site B and drop them at Site C.
    You will need to add an STM1 card(s) to Site B. Your ISP will need to provide the mapping structure of the STM1, so you can understand where the VC-12s, which contain the E1s, are located in the payload. You will then create circuits to map each E1 (the incoming VC-12s within VC3/VC4) from you ISPs STM1 at Site B, to the appropriate VC-12 on the outgoing STM16 line heading toward Site C. At Site C, you will need to map the VC-12s on the STM16 line to the appropriate port on an E1 line card.
    I hope this helps. Otherwise, you will need to have someone locally assist you in the explanation.
    Tom

  • Upgrade ONS 15454 M12 TCC2P from 9.4.03 to 10.0.11

    Hello, 
    quick question.
    I have in my lab one M12 subrack with only-one TCC2P card and I try to prepare software upgrade in customer network.
    I read all procedures at: http://www.cisco.com/c/en/us/td/docs/optical/15000r/upgrade/guide/b-454a10-0-1-upgrade.html
    My troubles started at point where I can select node where the software must be downloaded. The window is empty.
    Target version is "ons15454.DWDM.Lite.K9.R10011.pkg".
    Any idea?
    Thanks
    kvapa

    Hi Emyrsonn,
    I hope this ONS 15454 upgrade tool can help you answering all your questions
    http://www.cisco.com/web/techdoc/optical/15000r/upgrade/guide/ons-upgrade.html
    It seems like you should be able to directly upgrade from 9.1.x to 9.2.2.
    Please let me know if you have any comments on that.
    Hope it helps!

  • ONS 15454 problem turning up OC12

    Board.
    I am trying to turn up an OC12 (non-concatenated) that is muxed from a OC48. The OC48 terminates on an ONS 15454 on both sides. From there we run SM fiber to Cisco 12000 series onto an SM OC12/SMT4 Line card on both sides too.
    My settings for the ONS are as follows:
    Type=STS
    Size 12C
    Dir = 2way
    We see on one Cisco UP/DOWN, and on other Cisco Down/Down
    Does any on this forum have any tips at all?

    Which OC12 LC do you have on the 12000?
    CHOC12/STS3-IR-SC
    4OC12E/POS-IR-S
    4OC12X/POS-I-SC-B
    etc

  • ONS 15454 Chassis Document

    Hello All,
    I wanted to know if there is a document that will show how to put an ONS 15454 chassis together?  What each TCC, SMR, WXC card means and used for? What the DS, OSC, LINE, COM, EXP ports used for? Etc.
    If someone can point me in the right direction that would be great!
    Thanks!

    Well the product support pages show how to physically install y every componenet of the ONS equipment:
    http://www.cisco.com/en/US/products/hw/optical/ps2006/prod_installation_guides_list.html
    If you want an overview of the various cards' functions, please see the data sheets here:
    http://www.cisco.com/en/US/products/hw/optical/ps2006/products_data_sheets_list.html

  • ONS 15454 and AC/DC Converter for 220V

    I am looking for a AC/DC converter for a ONS15454 for a 220V input.
    The ONS 15454 datasheet indicate input current 22A maximum.
    The Cisco AC/DC Power Solution datasheet indicate for ONS 15454 a medium solution.
    And the same datasheet indicate the small solution is up to 32A for 220V.
    Then, can I use the small configuration for ONS at 220V?
    Anyone know that? Can you help me with that?
    Graciela

    What is the hardware configuration of your 15454 including chassis, fan and by slot?
    Using the hardware config, you can calcualte the expected amperage.
    http://www.cisco.com/en/US/partner/products/hw/optical/ps2006/products_tech_note09186a0080094ae4.shtml
    The general power requirement of 22A provides for any possible configuration. Actual configurations may be less. I have some 454s using as little as 9A in the lab.

  • ONS 15454 MRC 2.5G4

    Hi All,
    We are trying to install the optical multirate card (MRC 2.5Gig) on ONS 15454 and found the card comming up on standby state instead of active. The version running on the sonet box is 8.5.0 ...The MRC card port 1 is installed with the OC3 SFP's but cable not attached.
    Any help would be appreciated .
    Regards
    Anantha Subramanian Natarajan

    Hi, this is normal. Just go on and enable a SFP, called pluggable port module (PPM). After the first SFP is enabled, the state of the MRC card will change to working.
    Cheers
    Rene

  • ONS 15454 SDH with 2 ML cards connected to the same RPR

    I was wondering if I could connect 2 ML cards installed in the same ONS 15454 to the same RPR ring. Thanks!

    Bob,
    If you are wanting to tie the ML100 and the ML1000 into the same RPR Ring, then you have do do it with the POS interfaces.
    For Example:
    ML 100 POS 0   - North  Microwave
    ML 100 POS 1   - connect RPR to ML 1000 POS 0
    ML 1000 POS 1 - South Microwave
    North Microwave connects RPR to South Microwave
    This creates a single Loop or Ring
    It sounds like you are using your ML1000 as a Spur to another location.  In order to create an RPR ring, you must have the cards physically connected to each other in a continuous ring.
    Aaron Reed
    Carrier Escalation - Cisco Optical TAC

  • ONS 15454 Config Backup

    Does cisco have a tool to automate the database backup process for the ONS 15454?

    CTM - Cisco Transport Manager. It's Cisco's enterprise management tool for the optical products. It does a lot more than just backup the dbs - and has an accordingly non-trivial cost.
    See the info on the products and services pages at http://cisco.com/en/US/products/sw/opticsw/ps2204/index.html. The product data sheet (http://cisco.com/en/US/prod/collateral/netmgtsw/ps5730/ps2204/data_sheet_c78-518130.html) is a good start.
    Also see info under the support page at http://cisco.com/en/US/products/sw/opticsw/ps2204/tsd_products_support_series_home.html

Maybe you are looking for

  • Provisioning the user to OID

    Hi All, I am getting below error while provisioning user to OID in OIM 11gR2. Organization Lookup reconciliation and group lookup reconciliation working fine. Thor.API.Exceptions.tcColumnNotFoundException at Thor.API.tcMetaDataSet.getStringValue(tcMe

  • URGENT inventory reports

    Hi friends, I would like to see a report by Product line/Profit center, I checked these reports, MCBE,MMBE,MCBC,ME80AN. Where I don’t see any field that can show Profit center, And also I would like to see a inventory report  by material, qty, batch,

  • Background color project

    Okay, try to change the backgrund color for the project - as I understand: It works with a white generator, BUT: as far I put this under a clip having a masc the black background of the masc is still showing up in the timeline? How to get rid of this

  • I had forgotten the answers to my securiyy questions how do I change them so I can download stuff again

    How do I change it because I need to download my books for school. How do I Chang e the question or something. I need to be Able  to download stuff

  • Formatting SPRY Fields

    I've got a nice XML stream coming into my page that uses SPRY to read the XML and present the data. My problem is this...or should I say these, If I get in a data field that has time in it or a numeric field that I want to convert to currency I'm not