Cisco 3750G Integrated WLC upgrade failure

I am trying to upgrade our Cisco 3750G Integrated WLC from version 5 to version 7, at 92% I receive an error
Code file transfer failed - Error while writing output file
There is enough space on WLC,
Total System Memory............: 529088512 bytes
Used System Memory.............: 121180160 bytes
Free System Memory.............: 407908352 bytes
I have tried 2 different TFTP servers..
Any thoughts?

Hi,
1. Is it OK to upgrade to SWLC3750K9-5-2-193-0.aes ? or do I need to go through 4.2 first ?
ANS - Yes you have to upgrade to 4.2 first and then to 5.2, here is the doc..
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn52xgmr1.html#wp233853
2. Will that code upgrade the bootloader at the same time?
ANS - Yes, after upgrading the WLC code upgrade the boot loader.. the boot loader is 5.2.157 (BOOT)
3. How can I make sure there is enough flash space on the WLC?
ANS - Dont worry.. we have enough flash!!
4. Are there any special considerations to plan/prepare for?
ANS - Yes, please upgrade the WLC in a planned , scheduled maitenance window.
The DHCP issue is failure of associated clients to get an IP address with this message found in WLC debugging:
Wed Jul 20 17:16:37 2011: 00:19:db:5b:38:73 dhcpProxy: Dropping packet (no mscb) from STA 00:19:db:5b:38:73, giaddr:0.0.0.0, udpSrcPort:68, op:1
ANS - Issue the command ans see if that helps!!
WLC CLI access...
config dhcp proxy disable
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra

Similar Messages

Adding a second controller - 3750G integrated WLC

Hello all -
I'm new at this, so please bear with me.
I've been tasked to add a second WLC to a customer's network. They currently have a 4402-50 supporting 47 access points. The customer purchased a 3750G w/ integrated WLC (50AP) anticipating the addition of several more APs, but the addition is on hold. In the meantime, the customer would like the new WLC to help balance the AP load. The existing WLC is running 6.0.182.0. The customer has a mix of 1130, 1240, 1140 and 1250 APs. They are starting to use N features.
Both controllers are now on the same subnet 10.1.113.x. I've upgraded the code on the 3750G_WLC to match the other controller. Here are some questions I have now:
1. Am I right to think I need to set these two controllers in the same mobility group?
2. Am I right in thinking I will need to manually configure each AP to point to the controller I want it to be associated with? In other words, is there an AUTOMATIC load balancing feature? (NOTE: The customer just purchased and will have installed WCS)
3. Once we exceed 50 APs, will any other configuration changes need to happen?
This is all a little sketchy for me because we are right at the limit. So.. right now we are N+1 asking to load balance between the two. Once we exceed 50 APs, we're no longer N+1 and will need to designate which APs are high priority in case of failover.
Any tips on installing this second WLC into the network and any recommendations you may have for managing these 47 existing APs is appreciated.
Cheers -

So, when you define primary and secondary Controller, you specify the name of the controller. In 5.2 and above you also can specifiy the Management IP address of that controller. The AP will learn about these controller through the mobility group defined on the controllers.
About losing the controller, I didn't mean to configure priority after the fact. I meant that if you are trying to define priority (for the event that a controller was lost), then you would set the priority on the High Avail tab on the AP configuration. You would want to this when you install everything to begin with.
If you do not define primary/secondary, the AP should learn about the controllers from each controller, and when the controller sends its discovery replies, it should specify which one to load-balance to. Or something like that.
The bottom line is that if you don't have a primary/secondary defined, then the AP discovery process should get your AP on the least occupied controller. It is primary/secondary definitions that kind of overwrite this, which is what I was calling a "manual" load-balancing...
Does that help any more?

Cisco 3502i will not upgrade to 7.4.121.0 from 7.2.111.3 2504 WLC "Downloading"

Cisco 3502i will not upgrade to 7.4.121.0 from 7.2.111.3. 2504. Wireless tab continues to say "downloading" state on all APs. Temporary fix is to set WLC back to 7.2.11.3.
This is only happening on a few stores that are on one particular Prime Infrastructure box. Other stores on other Prime boxes not having this issue as well as most stores on the same box also not having this issue.
Anyone run into this and was able to resolve?

Scott, I have a few 2504 having this issue. Some having this issue if the site recovered from a power outage.
I can upload the image to other WLCs without issue. Its just these few on one particular PI, leading me to think that some of the WLC have corrupt images.
Yes, TAC told me the issue with 7.4 in the "downloading" state was that there was a communication issue between the AP and WLC and that I would need to get into the AP which I can not do, being it a remote site and FW security disabled this ability.
Some of TAC comments attached.

Run report --- Integration Error ----SSL failure

I have a form that call a report through the Run_Product Built, this works fine on Developer 6 version, but after I upgraded to 6i, everytime I press the buttonn that call the report, an error message will appear that say "FRM-41211 Integration Error SSL failure running another product" after the Report Background Engine appeared. And the report will not start.
But if I press the button again, all will be fine.
Does anyone know what happens ?
PLease help!!!!

It is a bug in Forms 6i and possible workaround (from Metalink) is:
WORKAROUND as follows :
This brings up the Background Engine on startup and minimizes it.
1. Create a shortcut for rwrbe60.exe and do a CTRL+C to copy it.
2. Right click on the TASK BAR at the bottom of the screen and get the TASKBAR
Properties box up.
3. Select ADVANCED
4. Expand Tree for PROGRAMS.
5. Click of STARTUP folder.
6. Do a CTRL+V to Paste in the Shortcut to rwrbe60.exe.
7. Right Click on Shortcut and select Properties.
8. Click Shortcut Tab.
9. Make sure of the following fields are as follows:
TARGET : {drive}:\{path}\rwrbe60.exe /c
START IN : Is the location of your Reports and Forms.
SHORTCUT KEY : None
RUN : MINIMIZED

5508 WLC Upgrade steps

Single 5508 WLC with 8 x 1142 APs.
5508 is running FUS 1.3, software version 7.0.116.0, field recovery image 6.0.182.0.
I need to bring the software version up to at least 7.2.115 to support 2 new 2602 AP i need to install.
Question is; do I install FUS 1.9 then update my controller to 7.6.120 or do I need to do any intermediate steps?
This is my first time upgrading a WLC so I'm fresh and this is a production WLC.
Cheers

Hi Fisher.
Normally It doesn't matter as long as you get it done but make sure that you reboot the WLC before doing the next.
Here is the procedure for FUS upgrade:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html
WLC Software upgrade Procedure:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/68835-wlc-upgrade.html
Regards
Dont forget to rate helpful posts

Cisco 3750G all links reset

I have a Cisco 3750G with routing enabled. Sometimes, I experience a situation: some clients computers are disconnected from the switch and then reconnected immediately. The whole things happened and ended within 5s. But it often happened, >5 times a day.
The log in switch shows:
Switch#sh logSyslog logging: enabled (0 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)No Active Message Discriminator.No Inactive Message Discriminator.    Console logging: level debugging, 373 messages logged, xml disabled,                     filtering disabled    Monitor logging: level debugging, 0 messages logged, xml disabled,                     filtering disabled    Buffer logging: level debugging, 373 messages logged, xml disabled,                     filtering disabled    Exception Logging: size (4096 bytes)    Count and timestamp logging messages: disabled    File logging: disabled    Persistent logging: disabledNo active filter modules.    Trap logging: level informational, 377 message lines loggedLog Buffer (4096 bytes):rface GigabitEthernet1/0/13, changed state to down1d21h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up1d21h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to upSwitch#
I didn't see any problems here, just some interfaces are down and then become up again. This happened not only on this single computer, but on some other devices including a Apple Airport Exterem.
Anyone has any idea about this?
Thanks in advanced.
UPDATE @ Feb 14 20:05 NST:
Configuration on that port is listed below:
Switch#sh run int gi1/0/13Building configuration...Current configuration : 66 bytes!interface GigabitEthernet1/0/13 switchport access vlan 30endSwitch#sh int gi1/0/13GigabitEthernet1/0/13 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 0014.a93b.830d (bia 0014.a93b.830d) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,     reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:13:27, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 14000 bits/sec, 7 packets/sec 5 minute output rate 175000 bits/sec, 8 packets/sec     802083047 packets input, 1214885172159 bytes, 0 no buffer     Received 34405 broadcasts (16832 multicasts)     0 runts, 0 giants, 0 throttles     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored     0 watchdog, 16832 multicast, 0 pause input     0 input packets with dribble condition detected     810796080 packets output, 62243896017 bytes, 0 underruns     0 output errors, 0 collisions, 2 interface resets     0 babbles, 0 late collision, 0 deferred     0 lost carrier, 0 no carrier, 0 PAUSE output     0 output buffer failures, 0 output buffers swapped outSwitch#sh hardCisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE8, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2013 by Cisco Systems, Inc.Compiled Wed 26-Jun-13 11:25 by prod_rel_teamImage text-base: 0x01000000, data-base: 0x02F00000ROM: Bootstrap program is C3750 boot loaderBOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)Switch uptime is 4 days, 1 hour, 52 minutesSystem returned to ROM by power-onSystem image file is "flash:c3750-ipservicesk9-mz.122-55.SE8/c3750-ipservicesk9-mz.122-55.SE8.bin"This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youSwitch#sh verCisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE8, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2013 by Cisco Systems, Inc.Compiled Wed 26-Jun-13 11:25 by prod_rel_teamImage text-base: 0x01000000, data-base: 0x02F00000ROM: Bootstrap program is C3750 boot loaderBOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)Switch uptime is 4 days, 1 hour, 52 minutesSystem returned to ROM by power-onSystem image file is "flash:c3750-ipservicesk9-mz.122-55.SE8/c3750-ipservicesk9-mz.122-55.SE8.bin"This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] WS-C3750G-24T (PowerPC405) processor (revision J0) with 131072K bytes of memory.Processor board ID CAT0929Z31BLast reset from power-on5 Virtual Ethernet interfaces24 Gigabit Ethernet interfacesThe password-recovery mechanism is enabled.512K bytes of flash-simulated non-volatile configuration memory.Base ethernet MAC Address       : 00:14:A9:3B:83:00Motherboard assembly number     : 73-8046-08Power supply part number        : 341-0048-03Motherboard serial number       : CAT09300BFAPower supply serial number      : DTH09262K40Model revision number           : J0Motherboard revision number     : B0Model number                    : WS-C3750G-24T-SSystem serial number            : CAT0929Z31BHardware Board Revision Number : 0x05Switch Ports Model              SW Version            SW Image------ ----- -----              ----------            ----------*    1 24    WS-C3750G-24T      12.2(55)SE8           C3750-IPSERVICESK9-MConfiguration register is 0xFSwitch#
UPDATE @ Feb 14 20:45 NST
Switch#sh controller e GigabitEthernet1/0/13     Transmit GigabitEthernet1/0/13           Receive   2153682004 Bytes                       3714795707 Bytes    810677366 Unicast frames               802082816 Unicast frames       149673 Multicast frames                 17023 Multicast frames        18389 Broadcast frames                 17786 Broadcast frames            0 Too old frames              3709393103 Unicast bytes            0 Deferred frames                2881529 Multicast bytes            0 MTU exceeded frames            2521075 Broadcast bytes            0 1 collision frames                   0 Alignment errors            0 2 collision frames                   0 FCS errors            0 3 collision frames                   0 Oversize frames            0 4 collision frames                   0 Undersize frames            0 5 collision frames                   0 Collision fragments            0 6 collision frames            0 7 collision frames             1320039 Minimum size frames            0 8 collision frames              250602 65 to 127 byte frames            0 9 collision frames              165765 128 to 255 byte frames            0 10 collision frames              77695 256 to 511 byte frames            0 11 collision frames             124005 512 to 1023 byte frames            0 12 collision frames          800179519 1024 to 1518 byte frames            0 13 collision frames                  0 Overrun frames            0 14 collision frames                  0 Pause frames            0 15 collision frames            0 Excessive collisions                 0 Symbol error frames            0 Late collisions                      0 Invalid frames, too large            0 VLAN discard frames                  0 Valid frames, too large            0 Excess defer frames                  0 Invalid frames, too small    802135613 64 byte frames                       0 Valid frames, too small       243436 127 byte frames      1271533 255 byte frames                      0 Too old frames       100832 511 byte frames                      0 Valid oversize frames        64915 1023 byte frames                     0 System FCS error frames      7029099 1518 byte frames                     0 RxPortFifoFull drop frame            0 Too large frames            0 Good (1 coll) frames            0 Good (>1 coll) framesSwitch#
UPDATE @ Feb 14 21:25 NST
Switch#test cable tdr interface G 1/0/13TDR test started on interface Gi1/0/13A TDR test can take a few seconds to run on an interfaceUse 'show cable-diagnostics tdr' to read the TDR results.Switch#sh cable tdr interface G 1/0/13TDR test last run on: March 05 03:07:45Interface Speed Local pair Pair length        Remote pair Pair status--------- ----- ---------- ------------------ ----------- --------------------Gi1/0/13 1000M Pair A     2    +/- 10 meters Pair B      Normal                Pair B     0    +/- 10 meters Pair A      Normal                Pair C     0    +/- 10 meters Pair D      Normal                Pair D     0    +/- 10 meters Pair C      NormalSwitch#
UPDATE @ 14:30 Feb 17 NST
Switch#test cable-diagnostics tdr interface G 1/0/15TDR test started on interface Gi1/0/15A TDR test can take a few seconds to run on an interfaceUse 'show cable-diagnostics tdr' to read the TDR results.Switch#show cable-diagnostics tdr int G 1/0/13TDR test last run on: March 05 03:07:45Interface Speed Local pair Pair length        Remote pair Pair status--------- ----- ---------- ------------------ ----------- --------------------Gi1/0/13 1000M Pair A     2    +/- 10 meters Pair B      Normal                Pair B     0    +/- 10 meters Pair A      Normal                Pair C     0    +/- 10 meters Pair D      Normal                Pair D     0    +/- 10 meters Pair C      NormalSwitch#

I'm pretty sure that the NIC and driver is not the problem.
Back in 2008, I had witnessed first-hand on how a brand new Intel GigabitEthernet NIC card reacts to legacy 3500XL switches. No matter what IOS you've loaded on the switch the links will go down/up between 25 to 45 times per minute. This will cause users very, very slow response. The easiest way to fix this issue is to force the NIC card to negotiate to 100/Full.
I am not saying to you have Intel NIC card but so far all suspects are on the table. Your wired NIC card has not been ruled out.
another Apple Airport Extreme which connected to this switch also experiencing this problem.
Hmmmm ... I'm reviewing the TDR result. What kind of cable is this? Is this a 1 metre cable? Can you please change this?

Why my Jabber 9.2.3 Sign in like Cisco UC Integration(TM) for Microsoft Lync?

After I uninstall Cisco UC Integration(TM) for Microsoft Lync 8.6 from my computer and reinstall Cisco Jabber 9.2(3), I found my Jabber got the same interface of sign in with Cisco UC Integration(TM) for Microsoft Lync. it let me input the TFTP,CTI,CCMCIP server adress, instead of choosing the presence server and inputing the presence server address and domain.
after I sign in, it is aslo like Cisco UC Integration(TM) for Microsoft Lync, there is not the side button of contacts list, I can only search the person to call and can not send message or chat any more.
I tried many times to uninstall and reinstall Jabber,i failed, except I install Jabber 9.1(3), it works well. but I try to reinstall 9.2(3) again, it goes back like Cisco UC Integration(TM) for Microsoft Lync,why?
Thx.

Hi,
You probably had CUCILync 9.2 installed previosly, and since CUCILync 9.2 is based on Jabber phone mode, the interfaces are the same. (You have Jabber phone mode nterface now)
These settings are written in jabber-boostrap.properties file and Jabber reads them from here.
That file is stored here:
C:\ProgramData\Cisco Systems\Cisco Jabber
If you delete thise file, interface should change.
If you want to install Jabber and avoid such things, do this with option clear=1
- msiexec.exe /i CiscoJabberSetup.msi CLEAR=1 ...
Regards,
Srdjan

FRM-41211: Integration Error: SSL failure running another product Error

Hai,
I am developing POS Application in Oracle(Forms6i/Reports6i). I design the Invoice Print Format in Reports6i and call from the Invoice Form. When the
user save the Invoice I Commit the Invoice and call the Invoice Report for Printing Immediately. I use Epson TM U210B Label Printer for Billing. Sometimes the Invoice Print is not coming in the Printer and it gives the
following error(especially the First print after restart the computer).
FRM-41211: Integration Error: SSL failure running
another product
After that if you print further for transaction no plm. only it gives the error first time of print
So Please give the solutions immediately. I am waiting for Ur favourable Reply.
Ur's Shahul

As Petr said make sure you're reports25_tmp is set in your registry and that the directory exists AND you have the rights to write to that directory.
You can also get this error if you try to issue a 2nd asynchronous run_product call to run a report and there is another one running. For this, Oracle has two 'solutions'.
1) Do not run more then one asynchronous report per session
or
2) Use a delay loop before calling the next report.
It's been my experience that #2 is worthless as, if it works, is doing pretty much the same thing as #1. I really hope this gets fixed (for good) at some point...somehow. <G>
Chad

Integration error SSL failure running another product. - Urgent

Anybody knows what could be the possible problem and how to solve it. This error is coming when I am running RUN_PRODUCT built-in forms 6i, that application was running for 2 years in Forms 5, without any problem.
I have included the message what Forms doucmentaion had.
FRM-41211: Integration error: SSL failure running another product.
Cause: There is a problem detected when launching another product.
Action: Check the RUN_PRODUCT built-in.
Level: 99
Type: Error
null

I got this error when I was using 4.5, it may be caused by the
correctness of report_path in registry.
Regards,
George
Anybody knows what could be the possible problem and how to solve it. This error is coming when I am running RUN_PRODUCT
built-in forms 6i, that application was running for 2 years in
Forms 5, without any problem.>I have included the message what
Forms doucmentaion had.>FRM-41211: Integration error: SSL
failure running another product.>Cause: There is a problem
detected when launching another product. >Action: Check the
RUN_PRODUCT built-in. >Level: 99 >Type: Error >null

Integration error SSL failure running another product

Dear All,
I am facing some problem while running reports from forms
SERVER:
•     OPERATING SYSTEM: Windows.8
•     Database: ORACLE 11g
•     Forms & Reports = 6i.
In form when click any report button to call report some time error comes.
FRM-41211: integration error SSL failure running another productAnd user can not print the report,

Forms/Reports 6i on Windows 8? I very much doubt that this is going to work. The last supported OS for Forms/Reports 6i was Windows XP.
You might have some luck with a non-supported workaround:
http://windows7bugs.wordpress.com/2012/08/25/windows-8-oracle-developer-suite-6i-patch-18/

Integration Error:SSL failure running another product.In DeveloperSuite 10g

I'm using DeveloperSuite 10g. I'm trying run the report from Forms but when I'm
clicking on button to run report using RUN_REPORT_OBJECT I'm getting following
error :
Integration Error : SSL failure running another product.
Can any one explain why I'm getting this error.
Regards
Alpesh.

Hi alpesh
I think you are good at oracleDS 10g and it is running on your machine successfully. But I am not able to run any form on my system.
My OS is Win XP with service Pack 2
Installed Oracle Database 10g
Installed Oracle DS 10g
Able to run reports on paper layout and web layout, But can not run forms. Error is shown on the IE Ver 7. Only source code is displayed. can you help me out from this.

Error : FRM-41211 : Integration Error: SSL Failure Running Another Product

Hi All
I am using Forms & Reports 10g.
I have a report .And i am trying to call in my forms and also i am passing parameters.
But i am getting this error :
My Code is :-
DECLARE
repid REPORT_OBJECT;
v_rep VARCHAR2(100);
rep_status VARCHAR2(20);
plid ParamList;
vParamValue number;
BEGIN
plid := Get_parameter_List('tmp');
IF NOT Id_Null(plid) THEN
Destroy_parameter_List( plid );
END IF;
plid := Create_parameter_List('tmp');
Add_Parameter(PLid, 'P_Block', Text_Parameter, :block_query.item_block);
Add_Parameter(PLid, 'P_Category', Text_Parameter, :block_query.item_category);
Add_Parameter(PLid, 'P_Dept', Text_Parameter, :block_query.item_dept);
Add_Parameter(PLid, 'P_Floor', Text_Parameter, :block_query.item_floor);
Add_Parameter(PLid, 'P_IP', Text_Parameter, :block_query.item_ip);
Add_Parameter(PLid, 'P_Room', Text_Parameter, :block_query.item_room);
Add_Parameter(PLid, 'P_Userid', Text_Parameter, :block_query.item_usr_id);
Add_Parameter(PLid, 'PARAMFORM', Text_Parameter, 'NO');
repid := FIND_REPORT_OBJECT('REPORT_Query');
SET_REPORT_OBJECT_PROPERTY(repid,REPORT_COMM_MODE,SYNCHRONOUS);
SET_REPORT_OBJECT_PROPERTY(repid,REPORT_DESTYPE,cache);
SET_REPORT_OBJECT_PROPERTY(repid,REPORT_DESFORMAT,'PDF');
SET_REPORT_OBJECT_PROPERTY(repid,REPORT_OTHER, 'paramform=no');
v_rep := RUN_REPORT_OBJECT(repid,plid);
rep_status := REPORT_OBJECT_STATUS(v_rep);
WHILE rep_status in ('RUNNING','OPENING_REPORT','ENQUEUED')
LOOP
rep_status := report_object_status(v_rep);
END LOOP;
WEB.SHOW_DOCUMENT('http://A_F2_ITT_PC_4.AAHOS.LOCAL:8890/reports/rwservlet/getjobid'||substr(v_rep,instr(v_rep,'_',-1)+1)||'?
*'||'server=Report_server_name&P_parameter='||'&block='''||:block_query.item_block*
*||'&category_name='''||:block_query.item_category*
*||'&dept='''||:block_query.item_dept*
*||'&floor='''||:block_query.item_floor*
*||'&ip_address='''||:block_query.item_ip*
*||'&room='''||:block_query.item_room*
*||'&usr_id='''||:block_query.item_usr_id*
*||'&paramform=no');*
End;
And the error i am getting is :- FRM-41211 : Integration Error: SSL Failure Running Another Product

hi
please try something like this.
DECLARE
repid REPORT_OBJECT;
v_rep VARCHAR2(100);
rep_status VARCHAR2(20);
plid ParamList;
vParamValue number;
BEGIN
plid := Get_parameter_List('tmp');
IF NOT Id_Null(plid) THEN
Destroy_parameter_List( plid );
END IF;
plid := Create_parameter_List('tmp');
add_parameter(plid,'p_parameter',text_parameter,to_char(:block.item));
Add_parameter(plid, 'PARAMFORM', TEXT_parameter, 'NO');
repid := FIND_REPORT_OBJECT('REPORT6');
SET_REPORT_OBJECT_PROPERTY(repid,REPORT_COMM_MODE,SYNCHRONOUS);
SET_REPORT_OBJECT_PROPERTY(repid,REPORT_DESTYPE,cache);
SET_REPORT_OBJECT_PROPERTY(repid,REPORT_DESFORMAT,'PDF');
SET_REPORT_OBJECT_PROPERTY(repid,REPORT_OTHER, 'paramform=no');
v_rep := RUN_REPORT_OBJECT(repid,plid);
rep_status := REPORT_OBJECT_STATUS(v_rep);
WHILE rep_status in ('RUNNING','OPENING_REPORT','ENQUEUED')
LOOP
rep_status := report_object_status(v_rep);
END LOOP;
/*Display report in the browser*/
WEB.SHOW_DOCUMENT('http://Machine_Name:8889/reports/rwservlet/getjobid'||substr(v_rep,instr(v_rep,'_',-1)+1)||'?
'||'server=repserver&P_parameter='||:block.item||
'&paramform=no');
END;

Cisco 4400 - 100 WLC ap manager IP address

I am going to implement a Cisco 4400-100 WLC. I need it to manage 100 Cisco LWAPP AP's
Can this be done with one AP Manager IP address?
Is it recommended to have the AP manager and manager address on the same subnet?
How many of the 4 fibre connectors need to be used to manage 100 AP's?
Mark Cronin

ok, you have 2 options one is work with AP MANAGER interfaces and the other is to work with LAG, whe LAG is enable you just need one AP MANAGER interface becouse the LAG makes the redundancy and load balancing function.
checkout this link:
http://cisco.com/en/US/docs/wireless/technology/controller/deployment/guide/dep.html
In this section:
Using Link Aggregation (LAG)

Cisco 5500 Series WLC Field Recovery Compatibility

Is Software Version 7.2.111.3 compatible with Field Recovery Image Version 7.6.95.16.

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154556/cisco-5500-series-wlc-field-recovery-compatibility

WLC upgrade due to Advisory

Hi,
We have a 5508 WLC running 7.2.110.0 and need to upgrade according to the advisory released today.
It seems we have three upgrade choices:
7.2.110.0 to 7.2.111.3
7.2.110.0 to 7.3.110.0
7.2.110.0 to 7.4.x
I've not upgraded one of these 5508's before, but if they are anything like ASAs then I need to be careful.
Can anyone advise if upgrading from our current version to 7.4 requires planning. Same for 7.3.
How will the WLC upgrades affect the APs (3502i) ?
How does one recover from a failed upgrade on these WLCs?
Thanks.

WLC version 7.4.100 will need Prime Infrastructure Version 1.3 to be managed, but Version 1.3 is not yet available to download at this time.
Huh? What is Prime Infrastructure and why do I need it?

Cisco 3750G Integrated WLC upgrade failure

Similar Messages

Maybe you are looking for