Cisco 3800 with NME-XD-48ES-2S-P module
I have a (Cisco) 3800 series router. It has a "NME-XD-48ES-2S-P" module (48 Ethernet ports). When issuing the command "#sh int brief" all is see is gigabit Ethernet or serial interfaces. I do not see any fast Ethernet ports. Can someone please guide me on how to see these ports...Thanks
Hey,
Use the command "service-module session g x/y session" to enter the service module. As its an independent module and run its own IOS. The port g x/y will be visible in router with 'sh ip int br' command.
HTH.
Regards,
RS
Similar Messages
-
Cisco Unity Express (NME-CUE) Compatibility for CUCM 9.1.2
I unable to find latest Compatibility matrix for Cisco Unity Express (NME-CUE) module for integrating with CUCM 9.1.2
The URL: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/compatibility/cuecomp.html is updated with CUCM 9.0 only.
Request to share Compatibility matrix or suggest Hardware and software for my below requirement.
I am running NME-CUE 7.0.6 on 2951 ISR2 with IOS version 15.2(4)M5 and integrated with CUCM 7.1.5 using SCCP.
I am upgrading my CUCM to 9.1.2 and need suggestion on upgrading the CUE.
Also need details on Licensing for approx 100 Mailbox and 25 Voice Ports (No need of IVR Ports).
Thanks,
ChandanHi Chandan,
CUE 8.6.6 and later are compatible with CUCM 9.1.x;
Support for Cisco Unified Communications Manager 9.1
Cisco Unity Express 8.6.6 provides support for Cisco Unified Communications Manager 9.1.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel8_6/rel_notes/rel_notes86.html#pgfId-411381
Because you are moving from a pre-7.1 CUE version you will need to follow the CSL License migration process;
NoteWhen you upgrade to Cisco Unity Express Release 8.6.x from any release prior to Cisco Unity Express Release 7.1, you must replace your pre-CSL licenses with CSL licenses. You must migrate your licenses for the mailbox features and port features. If you have purchased the optional IVR features, you should also migrate your licenses for the IVR features.
Software Activation for Cisco Unity Express 7.1 and Later Versions
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel7_1/Licensing/CUELicensing_book.html
Cheers!
Rob -
Creating VLAN on Cisco 3800 Series
Hello
I am new to networking. We have a Cisco 3800 series router with 64 ports. We have connected servers and PC's directly to the back of the router. Almost all of the ports are used with the exception of few. We would like to create a VLAN for the remaining few ports. I am able to telnet to the router or connect directly using hyper terminal.
I have been told that we cannot create VLAN's directly on the router. For that purpose we need to first get a switch and connect the switch to the router, then create VLAN’s using the switch. Can someone please provide some tips? Any suggestions would be nice…ThanksAppreciate you getting back. Here is the "show vlan-switch" output
----------------------->
#show vlan-switch
VLAN Name Status Ports
1 default active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
1 enet 100001 1500 - - - - - 1002 1003
1002 fddi 101002 1500 - - - - - 1 1003
1003 tr 101003 1500 1005 0 - - srb 1 1002
1004 fdnet 101004 1500 - - 1 ibm - 0 0
1005 trnet 101005 1500 - - 1 ibm - 0 0
---------------------->
As before I do not see any VLAN's set up. How come all the ports are not showing up on default VLAN 1. Maybe I can create a new VLAN and assign 2 or 3 ports to it. Please advise...Thanks -
Sample configuration of IME 7.0 with NME-IPS-K9 and How to get licence for NME-IPS-K9?
Dear all,
I already installed NME-IPS-K9 with Cisco Router 2821 series successfully and I used IME(Cisco IPS Manager Express 7.0.1) to configure NME-IPS-K9 but I never try with this before. I have some issue need everyone help:
1. Could you share the sameple for configuring IME with NME-IPS-K9 to monitor and manage all network traffice or package that attack to NME-IPS-K9?
2. Could you show me how to get licence for NME-IPS-K9?
Thanks everyone for your time to help me and share your great ideas.
I am really appreciated and looking for forward to hearing response from you all.
With my warm regards,
Sarem Phy
H/P:092562530CPU 100% on the NME-IPS module is normal. It will always show 100%. CPU on IPS is not related to the inspection load.
To check if the IPS module is overloaded, please check the "Inspection Load" speedometer. -
Does Cisco 3845 with NM-16A/S support OIR feature or Hot swap for this NM.
Dear Sir
My customer would like to implement Cisco 3845 with NM-16A/S x 4. I found that Cisco 3845 support OIR function but I am not sure OIR function that Cisco 3845 support, it support with which NM models. Can anyone tell me that NM-16A/S on Cisco 3845 support OIR function on this NM or not.
Thank you very much
WisitHi,
From what I have read from the following document.
http://www.cisco.com/en/US/products/ps5855/products_installation_guide_chapter09186a00802ccf1d.html
Network Modules
Network modules install directly into slots in the rear of the router. The Cisco 3845 router supports online insertion and removal (OIR, or hot swap) of network modules. The Cisco 3825 router does not support OIR.
Caution The Cisco 3845 router supports OIR with similar modules only. If you remove a network module, along with any installed WAN or voice interface cards, install another module and card combination exactly like it.
Interface Cards
Cisco 3800 series routers do not support OIR (hot swap) of interface cards inserted directly into router slots. You must turn off the router before installing or removing an interface card.
The Cisco 3825 router and the Cisco 3845 router each provide four interface card slots, labeled on the rear panel by HWIC and a number. Each slot can be occupied by one single-wide WIC, VIC, VWIC, or HWIC.
Hope this helps
Sarb -
CME B-ACD on Cisco 2911 with IOS 15.2(4)M5 not working
Hi Folks,
I am currently setting up CME version 9.1 with B-ACD (app-b-acd-aa-3.0.0.2.tcl & app-b-acd-3.0.0.2.tcl), running on
Cisco 2911 with IOS ver 15.2(4)M5, this is for lab purposes.
Below is my CME & B-ACD configuration :
voice service voip
ip address trusted list
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
h225 listen-port 1820
no call service stop
sip
bind control source-interface Vlan400
bind media source-interface Vlan400
registrar server expires max 600 min 60
voice register global
mode cme
source-address 172.25.202.1 port 5060
max-dn 2
max-pool 2
load 9971 sip9971.9-2-2SR1-9
authenticate register
timezone 28
time-format 24
date-format D/M/Y
tftp-path flash:
create profile sync 0004714411607756
voice register dn 1
number 3005
name br2phn2
voice register dn 2
number 3006
name br2phn4
voice register template 1
dialplan 1
voice register dialplan 1
type 7940-7960-others
pattern 1 3...
pattern 2 999
voice register pool 1
id mac 1C1D.86C4.0D6D
type 9971
number 1 dn 1
template 1
dtmf-relay rtp-nte
username 3005 password cisco
description 3214-3005
codec g711ulaw
voice register pool 2
id mac 1C1D.86C4.A574
type 9971
number 1 dn 2
template 1
dtmf-relay rtp-nte
username 3006 password cisco
description 3214-3006
codec g711ulaw
voice hunt-group 1 parallel
list 3002,3006
pilot 3210
application
service aa flash:/app-b-acd-aa-3.0.0.2.tcl
paramspace english index 1
param number-of-hunt-grps 2
param handoff-string aa
paramspace english language en
param max-time-vm-retry 2
param aa-pilot 3500
paramspace english location flash://
param second-greeting-time 60
param welcome-prompt _bacd_welcome.au
param call-retry-timer 15
param voice-mail 3001
param max-time-call-retry 90
param service-name queue
service aa-drop flash:/app-b-acd-aa-3.0.0.2.tcl
paramspace english index 1
param service-name queue
param drop-through-option 2
param second-greeting-time 60
paramspace english language en
param max-time-vm-retry 2
param max-time-call-retry 90
param voice-mail 3001
paramspace english location flash://
param aa-pilot 3501
param number-of-hunt-grps 1
param handoff-string aa-drop
param call-retry-timer 15
service queue flash:/app-b-acd-3.0.0.2.tcl
param queue-len 15
param aa-hunt10 3006
param queue-manager-debugs 1
param number-of-hunt-grps 2
param aa-hunt2 3210
interface Loopback0
ip address 172.25.110.3 255.255.255.255
ip ospf network point-to-point
h323-gateway voip interface
h323-gateway voip id Spain ipaddr 172.25.110.1 1719
h323-gateway voip h323-id BR2-RTR
h323-gateway voip tech-prefix 1#
h323-gateway voip bind srcaddr 172.25.110.3
interface Vlan400
ip address 172.25.202.1 255.255.255.0
ip pim dense-mode
dial-peer voice 3500 voip
service aa
destination-pattern 3500
session target ipv4:172.25.110.3
incoming called-number 3500
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 3501 voip
service aa-drop
destination-pattern 3501
session target ipv4:172.25.110.3
incoming called-number 3501
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
telephony-service
no auto-reg-ephone
max-ephones 2
max-dn 2 no-reg both
ip source-address 172.25.110.3 port 2000
cnf-file location flash:
load 7965 term65.default.loads
time-zone 28
time-format 24
date-format dd-mm-yy
max-conferences 8 gain -6
moh "music-on-hold.au"
web admin system name admin password cisco
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 14 2014 05:54:44
ephone-template 1
softkeys connected Endcall Hold Park Trnsfer Acct Flash
ephone-dn 1 octo-line
number 3001 no-reg both
description 3214-3001
name br2phn1
ephone-dn 2 octo-line
number 3002 no-reg both
description 3214-3002
name br2phn3
ephone 1
device-security-mode none
mac-address 189C.5DB6.D303
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7965
button 1:1
ephone 2
device-security-mode none
description 3214-3002
mac-address 984B.E194.FDDD
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7960
button 1:2
Problem :
1. When I test call from CME Phone both SIP and SCCP Phone by dial 3500 or 3501, I get the busy tone.
2. Debug voip dial-peer, match with dial-peer voice 3500 for (aa service) & 3501 for (aa-drop service).
3. Debug voice application script, show nothing.
Is there something wrong with my configuration ?
Rgds
NovriHi Novriadi,
In your configuration
service aa flash:/app-b-acd-aa-3.0.0.2.tcl
service queue flash:/app-b-acd-3.0.0.2.tcl
paramspace english location flash://
Remove "/" and "//" from the configuration
Then use the call application voice load command in privileged EXEC mode to reload the scripts.
Router# call application voice load aa
Router# call application voice load queue
Router# call application voice load aa-drop
You can refer to following document as well for more info
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/bacd/configuration/guide/cme40tcl/40bacd.html#wp1018270
Please find the sample configuration that is required to configure b-acd in CME for reference.
telephony-service
moh music-on-hold.au
multicast moh 239.1.1.1 port 2000
application
service queue flash:app-b-acd-2.1.0.0.tcl
param number-of-hunt-grps 2
param aa-hunt2 1111
param aa-hunt3 1222
param queue-len 15
param queue-manager-debugs 1
service aa flash:app-b-acd-aa-2.1.0.0.tcl
paramspace english index 1
paramspace english language en
paramspace english location flash:
param service-name queue
param handoff-string aa
param aa-pilot 8005550123
param welcome-prompt _bacd_welcome.au
param number-of-hunt-grps 2
param dial-by-extension-option 1
param second-greeting-time 60
param call-retry-timer 15
param max-time-call-retry 700
param max-time-vm-retry 2
param voice-mail 5003
dial-peer voice 222 voip
service aa
destination-pattern 8005550123
session target ipv4:192.168.1.1
incoming called-number 8005550123
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
Thanks & Regards,
Mudit Mathur -
Cisco UCM with Third Party Contact Center Solution
Hi all, hope everyone is well.
Anyone out there running Cisco UCM with a third party contact center solution ? would love to hear your experience on this subject.
Thanks in advance !!
DannyI have not heard of any sucessful stories, which vendor are you considering and what would you not go with UCCE/UCCX?
I used to work for Rockwell (Aspect today) which attempted to integrate their Business Contact Solution with CUCM (back on 3.3) and it worked OK for low volume calls, but never had any customer adoption.
I have not heard of any other known ACD vendors integrating with CUCM.
Chris -
Using Cisco WCS with Microsoft IAS
Hi.
I have two 5508 and WCS 7.0.172. I want to user Active Directory users credintals to login on ther WCS. Have a configurated NPS role on server with windows 2008 r2.
I have read this http://zmq503o1.wordpress.com/2008/01/06/using-cisco-wcs-with-microsoft-ias/ and done the same.
I dont't agree with "on the "Encryption" tab and clear all the checkboxes except "No encryption" - wants an encryption connection but this didn't work till in user's properites in AD permit "Reversible encryption". This is not what that I want. Would I need to generate ssl-cert for the wcs as wroted this?http://www.cisco.com/en/US/docs/wireless/wcs/7.0MR1/configuration/guide/hard.html#wp1042471
or doing smth else? thxCamera is only supported for use with CUVA. Any other application attempting to utilize the camera is not tested and is not supported.
-
Cisco IronPort with On Premise Exchange 2013
Hello All
The company I work for is in the process of starting an on premise Exchange 2007 to Exchange 2013 migration.
Most of the issues I don't think I'll have an issue with; however, where I am not finding much info is in regards to other companies using Cisco IronPort with Exchange 2013.
SO, I have two questions within this topic...
One, is anyone using Cisco IronPort with Exchange 2013 (on premise) out here?
Two, my manager is very controlling. I am the Exchange Admin; however, anything having to do with this IronPort thing with regards to Exchange HE has to do it. So, if anyone is familiar with this IronPort thing... How much work on the IronPort is going
to have to be done during this migration to keep things going?It shouldn't be any different with Exchange 2013 than it is with Exchange 2007.
Ed Crowley MVP "There are seldom good technological solutions to behavioral problems." -
Cisco 1700 with MP-BGP and VRF support
I have a Cisco 1721 with MP-BGP Support, you can create VRFs with it and every other MPLSVPN feature, but the commands for MPLS switching are not supported like Router(config-if)mpls ip , I read in some forums that you can create MPLS VPN without enabling MPLS at all, just with MPBGP, but I couldn't do it myself, Can someone tell me how to make it work or what can I do with a Cisco 1721 that supports MP-BGP?
thanks in advanceHere is an example. Take care about overhead for packets like VoIP. The overhead is 88 bytes.
The packet semms something like that.
IpHeader-pub@ - NAT-Tudp4500 - ESP - IpHeader-priv@(vrf discriminator) - GRE - Original IP Header - Data - Esp Trailer.
In this case you neet tunnel-mode because you use
private @ in order to determine vrf (vrf discriminator).
This is a LAB config, all other security parameters you need on a router are not configured. If you add access-list on the external interface of REMOTE you have to understand every encapsulation step in order to well tune it.
Good reading.
The PPT draw shows physically and logically views.
PS, take care about fragmentation issues, the problematic is still not well managed by the routers, I could not made Tunnel-path-mtu discovery work with vrf's. The workaround is to fragment packets. It's not good for performance but actually there is no other solution concerning that.
Kind Regards
Miguel -
I have a Cisco 2621 with 2FXS and 2FXO for my landlines, can I setup my 2821 to use my 2621 to make outside calls?
Sent from Cisco Technical Support iPhone AppThat should work in my opinion. The 2821 is running CCME? But is that worth the effort? Can't you place the VWICs into the 2821 instead in the 2621?
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni -
MIB Required for Bandwidth Monitoring on Cisco 3800 and 3900 series Routers
Hi Team,
Need your help here.
I am planning to do Bandwidth Monitoring on Cisco 3800 and 3900 series Routers. I want to know the exact MIB which I need to use for getting this done.
Thanks,
Karthik AnbumaniMatt, based on feature navigator GLBP is supportted on 3800 series.
Go to this link and search by feature (GLBP)
http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
HTH
Jorge -
I would like to know, who knows, how i can make a connection J2ME with NMEA protocol(GPS), somebody can give me a source code example? Thanks !!
You can find a very nice tutorial on http://servlet.java.sun.com/javaone/sf2002/conf/sessions/18-introductory-expanded.en.jsp
You should have found this if you had googled "j2me nmea", it was on the third place ;)
And now that you know this, can you write a GPS-spy program for me, because I'm a total newbe in this kind of stuff. (just kidding :) -
Cisco 1841 with PPP Internet link down
Hi brothers, please help.
We have Cisco 1841 with ATM card connect to Internet . Some days one Dialer interface of ISP is down and only restart router to get Dialer interface up again. I check debug PPP negotiation & see that no inbound packets from ISP.
I really need to fix this issue permanently, not need to restart router to recover Internet.
Thanks!
All line protocol from ATM0/0/0 & Dialer interfaces are up, but Dialer interface cannot get allocated IP addresses.
interface ATM0/0/0
description ISP Internet
no ip address
no atm ilmi-keepalive
dsl operating-mode itu-dmt
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 2
interface Dialer2
description ISP Internet 1
mtu 1492
bandwidth 8000
ip address negotiated
ip nat outside
no ip virtual-reassembly in
encapsulation ppp
dialer pool 2
dialer-group 2
ppp authentication chap callin
ppp chap hostname xxx
ppp chap password 7 xxx
no cdp enable
wr1#show ip int br
Interface IP-Address OK? Method Status Protocol
ATM0/0/0 unassigned YES NVRAM up up
ATM0/1/0 unassigned YES NVRAM up up
Dialer2 unassigned YES IPCP up up
wr1#show int atm0/0/0
ATM0/0/0 is up, line protocol is up
Hardware is HWIC-DSLSAR (with Alcatel ADSL Module), address is 001f.9e87.xxx(bia 001f.9e87.xxx)
Description: ISP Internet
MTU 4470 bytes, sub MTU 4470, BW 832 Kbit/sec, DLY 610 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Keepalive not supported
Encapsulation(s): AAL5
23 maximum active VCs, 256 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output 23:48:07, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 1084
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
58124 packets input, 30790858 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 348 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
51848 packets output, 16773091 bytes, 0 underruns
6 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
wr1#show int dia2
Dialer2 is up, line protocol is up (spoofing)
Hardware is Unknown
Description: ISP Internet
Internet address will be negotiated using IPCP
MTU 1492 bytes, BW 8000 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Closed, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Interface is bound to Vi2
Last input never, output never, output hang never
Last clearing of "show interface" counters 1d00h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Class-based queueing
Output queue: 0/1000/0 (size/max total/drops)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
52937 packets input, 30470954 bytes
52931 packets output, 17287959 bytes
Bound to:
Virtual-Access2 is up, line protocol is down
Hardware is Virtual Access interface
MTU 1492 bytes, BW 8000 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent
PPPoATM vaccess, cloned from Dialer2
Vaccess status 0x44
Bound to ATM0/0/0 VCD: 1, VPI: 0, VCI: 38, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 5 seconds on reset
Interface is bound to Di2 (Encapsulation PPP)
Last input 00:00:09, output never, output hang never
Last clearing of "show interface" counters 1d00h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 40403
Queueing strategy: Class-based queueing
Output queue: 65/1000/0 (size/max total/drops)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
58124 packets input, 30591958 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
93405 packets output, 17935575 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
syslog for debug ppp negotiation:
2014-09-10 08:49:31 Local7.Notice local IP address 801: wr1.lon: .Sep 10 01:51:33.803: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0/0, changed state to down
2014-09-10 08:49:32 Local7.Notice local IP address 804: wr1.lon: .Sep 10 01:51:35.247: %TRACKING-5-STATE: 3 ip sla 3 state Up->Down
2014-09-10 09:13:40 Local7.Error local IP address 808: wr1.lon: Sep 10 02:15:42.646: %LINK-3-UPDOWN: Interface ATM0/0/0, changed state to up
2014-09-10 09:13:40 Local7.Notice local IP address 809: wr1.lon: Sep 10 02:15:43.646: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0/0, changed state to up
2014-09-10 09:13:45 Local7.Error local IP address 810: wr1.lon: Sep 10 02:15:48.957: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
2014-09-10 09:13:45 Local7.Debug local IP address 811: wr1.lon: Sep 10 02:15:48.961: Interface Virtual-Access2 max_reserved_bandwidth config will not
2014-09-10 09:13:45 Local7.Debug local IP address 812: wr1.lon: take effect on the queueing features configured via service-policy
2014-09-10 09:13:45 Local7.Info local IP address 813: wr1.lon: Sep 10 02:15:48.965: %DIALER-6-BIND: Interface Vi2 bound to profile Di2
2014-09-10 09:13:45 Local7.Debug local IP address 814: wr1.lon: Sep 10 02:15:48.965: Vi2 PPP: Sending cstate UP notification
2014-09-10 09:13:45 Local7.Debug local IP address 815: wr1.lon: Sep 10 02:15:48.969: Vi2 PPP: Processing CstateUp message
2014-09-10 09:13:45 Local7.Debug local IP address 816: wr1.lon: Sep 10 02:15:48.973: PPP: Alloc Context [662C56A4]
2014-09-10 09:13:45 Local7.Debug local IP address 817: wr1.lon: Sep 10 02:15:48.973: ppp3 PPP: Phase is ESTABLISHING
2014-09-10 09:13:45 Local7.Debug local IP address 818: wr1.lon: Sep 10 02:15:48.973: Vi2 PPP: Using dialer call direction
2014-09-10 09:13:45 Local7.Debug local IP address 819: wr1.lon: Sep 10 02:15:48.973: Vi2 PPP: Treating connection as a callout
2014-09-10 09:13:45 Local7.Debug local IP address 820: wr1.lon: Sep 10 02:15:48.973: Vi2 PPP: Session handle[14000004] Session id[3]
2014-09-10 09:13:45 Local7.Debug local IP address 821: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP: Event[OPEN] State[Initial to Starting]
2014-09-10 09:13:45 Local7.Debug local IP address 822: wr1.lon: Sep 10 02:15:48.973: Vi2 PPP: No remote authentication for call-out
2014-09-10 09:13:45 Local7.Debug local IP address 823: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP: O CONFREQ [Starting] id 1 len 14
2014-09-10 09:13:45 Local7.Debug local IP address 824: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:13:46 Local7.Debug local IP address 825: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:46 Local7.Debug local IP address 826: wr1.lon: Sep 10 02:15:48.973: Vi2 LCP: Event[UP] State[Starting to REQsent]
2014-09-10 09:13:48 Local7.Debug local IP address 827: wr1.lon: Sep 10 02:15:50.965: Vi2 LCP: O CONFREQ [REQsent] id 2 len 14
2014-09-10 09:13:48 Local7.Debug local IP address 828: wr1.lon: Sep 10 02:15:50.965: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:13:48 Local7.Debug local IP address 829: wr1.lon: Sep 10 02:15:50.965: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:48 Local7.Debug local IP address 830: wr1.lon: Sep 10 02:15:50.965: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:50 Local7.Debug local IP address 831: wr1.lon: Sep 10 02:15:52.981: Vi2 LCP: O CONFREQ [REQsent] id 3 len 14
2014-09-10 09:13:50 Local7.Debug local IP address 832: wr1.lon: Sep 10 02:15:52.981: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:13:50 Local7.Debug local IP address 833: wr1.lon: Sep 10 02:15:52.981: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:50 Local7.Debug local IP address 834: wr1.lon: Sep 10 02:15:52.981: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:52 Local7.Debug local IP address 835: wr1.lon: Sep 10 02:15:54.996: Vi2 LCP: O CONFREQ [REQsent] id 4 len 14
2014-09-10 09:13:52 Local7.Debug local IP address 836: wr1.lon: Sep 10 02:15:54.996: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:13:52 Local7.Debug local IP address 837: wr1.lon: Sep 10 02:15:54.996: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:52 Local7.Debug local IP address 838: wr1.lon: Sep 10 02:15:55.000: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:54 Local7.Debug local IP address 839: wr1.lon: Sep 10 02:15:57.012: Vi2 LCP: O CONFREQ [REQsent] id 5 len 14
2014-09-10 09:13:54 Local7.Debug local IP address 840: wr1.lon: Sep 10 02:15:57.012: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:13:54 Local7.Debug local IP address 841: wr1.lon: Sep 10 02:15:57.012: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:54 Local7.Debug local IP address 842: wr1.lon: Sep 10 02:15:57.012: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:56 Local7.Debug local IP address 843: wr1.lon: Sep 10 02:15:59.028: Vi2 LCP: O CONFREQ [REQsent] id 6 len 14
2014-09-10 09:13:56 Local7.Debug local IP address 844: wr1.lon: Sep 10 02:15:59.028: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:13:56 Local7.Debug local IP address 845: wr1.lon: Sep 10 02:15:59.028: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:56 Local7.Debug local IP address 846: wr1.lon: Sep 10 02:15:59.028: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:13:58 Local7.Debug local IP address 847: wr1.lon: Sep 10 02:16:01.044: Vi2 LCP: O CONFREQ [REQsent] id 7 len 14
2014-09-10 09:13:58 Local7.Debug local IP address 848: wr1.lon: Sep 10 02:16:01.044: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:13:58 Local7.Debug local IP address 849: wr1.lon: Sep 10 02:16:01.044: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:13:58 Local7.Debug local IP address 850: wr1.lon: Sep 10 02:16:01.044: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:14:00 Local7.Debug local IP address 851: wr1.lon: Sep 10 02:16:03.060: Vi2 LCP: O CONFREQ [REQsent] id 8 len 14
2014-09-10 09:14:00 Local7.Debug local IP address 852: wr1.lon: Sep 10 02:16:03.060: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:14:00 Local7.Debug local IP address 853: wr1.lon: Sep 10 02:16:03.060: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:14:00 Local7.Debug local IP address 854: wr1.lon: Sep 10 02:16:03.060: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:14:02 Local7.Debug local IP address 855: wr1.lon: Sep 10 02:16:05.075: Vi2 LCP: O CONFREQ [REQsent] id 9 len 14
2014-09-10 09:14:02 Local7.Debug local IP address 856: wr1.lon: Sep 10 02:16:05.075: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:14:02 Local7.Debug local IP address 857: wr1.lon: Sep 10 02:16:05.075: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:14:02 Local7.Debug local IP address 858: wr1.lon: Sep 10 02:16:05.075: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:14:04 Local7.Debug local IP address 859: wr1.lon: Sep 10 02:16:07.091: Vi2 LCP: O CONFREQ [REQsent] id 10 len 14
2014-09-10 09:14:04 Local7.Debug local IP address 860: wr1.lon: Sep 10 02:16:07.091: Vi2 LCP: MRU 1492 (0x010405D4)
2014-09-10 09:14:04 Local7.Debug local IP address 861: wr1.lon: Sep 10 02:16:07.091: Vi2 LCP: MagicNumber 0x24FF1F46 (0x050624FF1F46)
2014-09-10 09:14:04 Local7.Debug local IP address 862: wr1.lon: Sep 10 02:16:07.091: Vi2 LCP: Event[Timeout+] State[REQsent to REQsent]
2014-09-10 09:14:06 Local7.Debug local IP address 863: wr1.lon: Sep 10 02:16:09.107: Vi2 PPP DISC: LCP failed to negotiate
2014-09-10 09:14:06 Local7.Debug local IP address 864: wr1.lon: Sep 10 02:16:09.107: PPP: NET STOP send to AAA.
2014-09-10 09:14:06 Local7.Debug local IP address 865: wr1.lon: Sep 10 02:16:09.107: Vi2 PPP: No remote authentication for call-out
2014-09-10 09:14:06 Local7.Debug local IP address 866: wr1.lon: Sep 10 02:16:09.107: Vi2 LCP: Event[Timeout-] State[REQsent to Stopped]
2014-09-10 09:14:06 Local7.Debug local IP address 867: wr1.lon: Sep 10 02:16:09.107: Vi2 LCP: Event[DOWN] State[Stopped to Starting]
2014-09-10 09:14:06 Local7.Debug local IP address 868: wr1.lon: Sep 10 02:16:09.107: Vi2 PPP: Phase is DOWNHello ,
As line comes up after reloading the device this does not looks like configuration issue but hardware .
Either connection between ATM card and modem is getting idle or some issue with ATM card .
Did you try replacing ATM card with a spare one to see if issue persists .
HTH
Sunil Bhadauria
! Kindly rate all helpful posts and accordingly mark correct answers to help forum ! -
Configuration of CISCO 3502I with Windows 2003 Server SE
Hi,
I am currently trying to configure a CISCO Aironet AIR-CAP3502I-E-K9 with Win Server 2003 Standard Edition.
First of all is it even possible to cinfigure the above device using DHCP so that it can be run as an access point or can it only be used with a CISCO Controller,
Does the server need to be a Win 2003 Ent?
In my situation the Windows Server is the controller we don't have a CISCO controller
I have created a Vendor class attribute on the DHCP pool of the windows server using option 43
The IP address of the DHCP server is 10.203.125.48 but the users are sitting on the 10.203.122.xxx subnet. The AP is currebtly sitting on the same subnet as the DHCP server(125)
I have created an Option Class called 'CISCO Ap' with an option code of 241 on the DHCP scope
Under Scope options I have then created an option 241 option name and under 'Available Options' ticked the option 43 and added the name of the DHCP server IP address.
When I switch on the AP it is blinking green but I get the following error attached.
Any Help would be appreciated
Thanks
ImmyThat error is "normal" because you are using a 3500 AP. This particular model of AP requires a wireless LAN controller (WLC).
You "cannot" load autonomous IOS into the 3500 for wireless service.
Maybe you are looking for
-
Is it possible to Recall an Email Message
I am fairly certain that it's not possible. But on the Windows Outllook side, there is the option to recall or rescind an email message. Is there a Mac OS Mail equivalent, or SW add-on that adds this capability? Not an everyday feature, but when need
-
Portal 4.0 with MS SQL Server 2000 using CLOBs
Hello, I'm driving Portal 4.0 with MS SQL Server 2000. I have encountered serious problems when trying to persist events (e.g. RuleEvent) to database. In my application-config.xml file I have JdbcHelper attributes ShouldUseClobsForReads & -Writes set
-
Shopping Cart Purchasing Group
We are using the classic Scenario in SRM7.02 ECC6.04 Upon replicating purchase requisitions, direct purchase requisitions are assigned to the purchasing group of the Entry channel and requisitions with account assignment K are assigned to the correct
-
Preloader not working althought it loads fine
im trying to make a preloader, althought it loads just fine the preloader bar wont move, better: the filesize against the loaded bytes does not let it move http://pastebin.com/SLQeqx7U code is there, i dont know if this forums have [code] thing
-
Copying applications to SD card
i just got a new centro and am new to the palm world. i copied an application to my SD card "package installer" now i want to delete it from the SD card. how do i do this? when opening the "files" application, i cannot find where it is saved. can som