Cisco 3850 Mobility Agent unable to connect clients

Hi
We are trying to use Cisco 3850 as Mobility agents with 5760. We can't seem to get the clients to authenticate to the radius server. We don't even see them appear in the radius logs.
We have defined the radius server and the profile
wlan Wireless 2 WAP
aaa-override
accounting-list Radius
client vlan wireless
security dot1x authentication-list Radius
session-timeout 1800
no shutdown
radius server Primary
address ipv4 x.x.x.x auth-port 1812 acct-port 1813
timeout 5
retransmit 2
key 7 ........
radius server Primary
address ipv4 x.x.x.x port 1812 acct-port 1813
timeout 5
retransmit 2
key 7 .........
The client appears to connect to the AP but can't authenticate so gets kicked off
If we do a test aaa group username password then it says that it's sucessful.
In the debug we get 802.1X required but then it never seems to get any further.

Alright, so I finally figured out the issue with this. I had a Mobility Anchor set on the guest WLAN and once I removed that all started working again.
What is Mobility Anchor?
A. Mobility Anchor, also referred to as Guest tunneling or Auto Anchor Mobility, is a feature where all the client traffic that belongs to a WLAN (Specially Guest WLAN) is tunneled to a predefined WLC or set of controllers that are configured as Anchor for that specific WLAN. This feature helps to restrict clients to a specific subnet and have more control over the user traffic. Refer to the Configuring Auto-Anchor Mobility section of Cisco Wireless LAN Controller Configuration Guide, Release 7.0 for more information on this feature.

Similar Messages

Unable to connect clients to WAP121

I have an issue with a WAP121.
It's in an extremely congested area, and most client devices are unable to connect.
The log (see below extract) shows repeated entries for reason 3.
The AP is config'd with a fixed channel (6), and I've tried turning off 'n' support. It's running firmware version 1.0.4.4.
What is happening here, and how should I fix it? Currently its embarrassingly been replaced by a £15 TP-Link AP (don't ask..) which is functioning perfectly, so although it's a harsh environment it's clearly possible :)
Thanks all.
J
Aug 5 2014 01:10:43
info
hostapd[4140]
wlan0: IEEE 802.11 Assoc request from b8:c7:5d:d5:87:3c BSSID 3c:08:f6:24:26:dc SSID WirelessLink
Aug 5 2014 01:10:43
info
hostapd[4140]
wlan0: IEEE 802.11 STA b8:c7:5d:d5:87:3c deauthed from BSSID 3c:08:f6:24:26:dc reason 3: STA is leaving IBSS or ESS

My name Eric Moyers. I am an Engineer in the Small Business Support Center.
I am sorry to hear that you are experiencing this issue. Since I am not sure which settings you have tried, I am listing everything I do and check below. If it is something that you have tried please excuse me.
Here are a couple of things to try to resolve this issue:
1) If you have more than one device and the devices are in Cluster Mode or Single Point Setup, I would ask that you disable that as a test.
2) Go to Wireless-Bandwidth Utilization tab and disable Bandwidth Utilization.
3) Go to Wireless-Radio tab, under Legacy Rate Sets supported and basic disable rates 1 and 2.
4) Change fixed multicast from auto to 54.
5) Disable the "Broadcast key refresh rate" duration from 300 seconds to 0 seconds.
6) If you have not already completed a wireless scan of the network area, you can do that using the Wi-Fi Analytics tool found here: http://www.ampedwireless.com/wifianalytics/
It is a free download and I like it a lot.
If this does not improve your issue, please call our support center and open a case so that one of our engineers can work directly with you.
Also just as information the diagnostic download you did (diagnostic after reboot) is a real-time snapshot. It just shows what is going on at that moment in time.
Eric Moyers
.:|:.:|:. CISCO | Cisco Technical Support | Wireless and Surveillance Subject Matter Expert
Please rate helpful Posts and Let others know when your Question has been answered.

Cisco 871W eZVPN is unable to connect Cisco PIX vpn server

crypto ipsec client ezvpn TEST
connect auto
group Cisco key cisco123
mode client
peer 172.1.1.1
xauth userid mode interfactive
interface FastEthernet4
ip address 10.1.1.1 255.255.255.0
ip access-group 101 in
ip nat outside
crypto ipsec client ezvpn TEST
Internet Vlan1
ip address 192.168.1.1 255.255.255.0
ip access-group 100 out
ip nat inside
crypto ipsec client ezvpn TEST inside
ip route 0.0.0.0. 0.0.0.0 192.168.1.254
ip nat inside source route-map EzVPN1 interface FastEthernet4 overload
access-list 100 permit ip any any
access-list 101 permit ip any any
access-list 103 permit ip 192.168.1.0 0.0.0.255 any
route-map EzVPN1 permit 1
match ip address 103
These are the following commands I applied in my Router, It is able to connect but unable to access any other servers. The same user name & password I tried with the VPN dialer it works on my Laptop. Anything I am missing on the router configuration. The VPN server is Cisco PIX 515E.
Cisco IOS on 871W is 12.3(8)Y12

1) Isn't your default route supposed to be pointing towards the external interface?
ip route 0.0.0.0. 0.0.0.0 192.168.1.254 ?
2) Can you change the 'mode client' to 'mode network-extension'. Also the PIX will need 'nem enable'.
Have a look at the following (I'm assuming you already have as your config seems to be similar):
http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080809222.shtml
For old 6.x code on PIX, have a look at:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080241a0d.shtml
Regards
Farrukh

Unable to connect client to vpn on rv082

Hello all,
We currently have an RV082 and an RV180W at our remote site. Our VPN tunnel is up gateway to gateway but whenever I try to use quick connect I can't connect and get failed to establish connection message. I've created a user in client to gateway. I've also tried various WAN IP addresses from our ISP. Any help you have would be useful, thanks!

Hi,
It looks like you did not create the client to gateway VPN in either the RV082 and the RV180W. In order to use the VPN user that you created in that router, you must create the client to gateway VPN inside that router. For example, you will have to configure PPTP VPN which is a client to gateway VPN and create a user in the RV180W. After that, you would set up the Windows default VPN set up. Please make sure that you use the WAN IP address of the RV180W that the client to gateway VPN was created in and use the VPN user that was created in that router as well. One last thing is that our Cisco Small Business routers do not support "Cisco Quick Connect."
I hope that made sense and please keep me posted or feel free to give us a call at 1-866-606-1866.

Monodevelop unable to connect to 127.0.0.1:35815

When I try to debug apps in monodevelop as casual user, the only thing I see is this message:
debugger-agent: Unable to connect to 127.0.0.1:35815
Press any key to continue...
But when I do it as root - there is no problem. Something wrong with permissions?
Last edited by AlexRu (2013-06-27 01:23:10)

I am sorry, my previous statement was wrong. Problem occurs, when I am creating console app, no matter if I am root or not... Projects of other types can be debbuged with no concern

Cisco prime 2.1 not showing wired clients connected to Cisco 3850 switches

Hello All,
I have around 80 Cisco 3850 switches at a customer network and they are using prime infrastructure 2.1.2 to manage these devices. Most of the features are working fine except that the prime does not show the wired clients connected to the switches. The wireless clients are shown properly but not the wired clients. Their core switches are nexus 7k. The SNMP configuration on the switches is as follows.
snmp-server group xxxx v3 priv write xxxx-VIEW-WR
snmp-server view xxx-VIEW-WR mib-2 included
snmp-server trap-source Vlan100
snmp-server host x.x.x.x version 3 priv testuser
Please help me to resolve this issue.
Shabeeb

I managed to get the end hosts connected in 3850 switches with the use of snmp context command. But now the issue is that prime is showing only the mac address of the device , not the IP address.
Is there anyway to resolve this issue?

Cisco Security Agent unable to close tcp/135 port on Windows hosts

Hello
I've encountered with problem that Cisco Security Agent unable to close port TCP/135 on windows PC (XP or Win7).
I've configured rule module Network Access Control to prevent all client/server connections to port tcp/135.
I've checked my policy using nmap, so this port (TCP/135) during 20 minutes shows as filtered and i can see log in monitor event on CSA MC, during next 20 minutes it show as opened and no log shows. (time not exact, so it maybe 30 minutes or 5,it varies)
Can anyone explain how TCP/135 works and is it possible to close it using CSA?
Thanks in advance

There is another question for the same issue on the forums (see: CSA 6.0.2.145 problem with windows 7 firewall). I wrote:-
"I went ahead and tested this in the lab with winXP and CSA 602-149 (latest). I defined a rule with DENY tcp/135 and ran the nmap and it reports opened (wireshark shows syn-ack to the syn). I changed it to a PRIORITY DENY and now the nmap reports closed (wireshark shows reset to the syn). Via the cli, netstat -an shows the pc listening on tcp/135 & disabling CSA the syn gets the syn-ack response. To me this implies a couple of defect. 1: The DENY should block syn to tcp135 & 2: CSA should not send reset (it should be reset). Is it possible to open a TAC case and put my name (mwinnett) in it and I will open a defect."
Matthew

Error "Test Agent could not connect to the test controller" while configuring the Test Agent on Client machine

Hi,
I am getting an Error “Test Agent could not connect to the test controller”
while configuring The Test Agent on Client machine.
Pre-requisite used:
VS2012 update 4, Test agent & Test controller of same version used
User has TFS admin access.
Same user id used for configuring Test Agent.
Description:
Test controller is installed on server A. I want to install test agent on client machine B.
Windows Fire wall is OFF on both Machines A & B. While configuring Test Agent below error is occurred:
“Test Agent could not connect to the test controller”
In log file error was “I, 2015/04/02, 15:32:21.723, Could not get the status from the test agent. Exception: Failed to connect to an IPC Port: The system cannot find the file specified.”
In Event viewer below error details given:
Unable to connect to the controller on ‘My Server: 6901’. The agent can connect to the controller but the controller cannot connect to the agent because of following reason: The requested name is valid, but no data of the requested type was found.
Make sure that the firewall on the test agent machine is not blocking the connection.
Could you please help me to find solution?
Thanks in advance!
Kanchan M
Kanchan

Hi Kanchan,
So on each computer, you create a local user account that is a member of the Administrators group, and use the same account and password on each machine(controller and Agent), am I right?
Could you enable the detailed log message?
http://blogs.msdn.com/b/aseemb/archive/2010/03/07/how-to-enable-test-agent-logs.aspx
http://blogs.msdn.com/b/aseemb/archive/2009/11/28/how-to-enable-test-controller-logs.aspx
>>In log file error was “I, 2015/04/02, 15:32:21.723, Could not get the status from the test agent. Exception: Failed to connect to an IPC Port: The system cannot find the file specified.”I
met a similar issue before which was related to the Firewall exceptions, maybe you could refer to it here:
http://stackoverflow.com/questions/12249093/test-agent-could-not-connect-to-the-test-controller-vs2012-agents
Best Regards,
Jack
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

MAC OS X unable to download Cisco ISE supplicant agent

Hi,
I have a problem with MAC OS X clients unable to download the Cisco ISE supplicant agent using Safari browser but able to login on the ISE guest portal. If the same client was to login to the ISE guest portal using Firefox; it has no issues downloading the ise supplicant and posture agent.
I have tried to update the Java version on the client to the latest; however it does not resolve the issue. As I am new to MAC OS clients; I was wondering what may be the cause of the issue?
I have summarized the issue as follows:
1. MAC OS X 10.8 with safari 6 -- unable to download agent but can login successfully on the Cisco ISE guest portal
2. MAC OS X 10.8 with Firefox -- able to login to Cisco ISE guest portal and download agents; no issues
3. MAC OS X 10.7 with safari and firefox --- unable to download agent but can login successfully on the Cisco ISE guest portal
4. Windows XP & Windows 7 & Iphone/Ipad/Android -- able to login/download agent without any issues
Any suggestions is appreciated.
Thanks.

For Agent Download Issues on Client Machine
• Ensure that a client provisioning policy exists in Cisco ISE. If yes, verify the
policy identity group, conditions, and type of agent(s) defined in the policy.
(Also ensure whether or not there is any agent profile configured under Policy >
Policy Elements > Results > Client Provisioning > Resources > Add > ISE
Posture Agent Profile, even a profile with all default values.)
• Try reauthenticating the client machine by bouncing the port on the access
switch.
Remember that the client provisioning agent installer download requires the following:
• The user must allow the ActiveX installer in the browser session the first time an agent is installed
on the client machine. (The client provisioning download page prompts for this.)
• The client machine must have Internet access.
Client Machine Operating Systems and Agent Support in Cisco ISE
Check the following link
http://www.cisco.com/en/US/docs/security/ise/1.1.1/compatibility/ise_sdt.html#wp95449

UCCX 7 SR5 agent login gives timeout - unable to connect to UCCX server

Team - running high availability. The CAD login for UCCX 7 SR5 gives occasionally timeout errors.
Unable to connect to UCCX server. What is the root cause of this?
on CAD client PC based on Cisco recommendation
C:\Program Files\Cisco\Desktop\config, we changed PhoneDev.cfg.
added ->
[ReqTimeout]
Milliseconds=30000
While this helped it still happens. Is this a bug you have seen?
What could be done for the root cause.

Hello,
This happens because the CAD client software is timing out due to not receiving a response from the UCCX server in the configured and default
10 seconds. Increasing the timeout alleviates the symptom, but the root cause could be slowness or connectivity problems between CUCM and AD. The default timeout between them is 30 seconds. You can check if you have an DC/GC down or not responsive or point your CUCM to authenticate to a local DC/GC, but definitely need to check on the CUCM / AD side.
CSCta49259 CAD client timeout value not present in PhoneDev.cfg
Symptom:
Per MIVR logs CAD side is timing out and changes to the server-side properties did not resolve the issue.
Conditions:
UCCX 7.0(1) CAD
Workaround:
on CAD client PC
C:\Program Files\Cisco\Desktop\config, there should be a file
called PhoneDev.cfg.
add ->
[ReqTimeout]
Milliseconds=30000
save then restart the CAD client .
HTH
Pablo

Ad agent connection erro unable to connect to server :0

Hello i want to configure ad agent 1.0.0.32 build 539 on windows server 2008 with patch installed.
but when i execute adactrl show running i see that
Cisco AD Agent adactrl -- version 1.0.0.32, build 539
Connection error. Unable to connect to server:0
An exception occured! connection Error
For further information use:
adactrl help
i test adactrl restart, reboot server no change.
nps must be install ?

Hi
I am running into the same error trying to setup AD agent Windows 2003 Server Standard Edition with SP2 (and I have disabled the Windows Firewall). The AD Agent is installed on the same machine as the domain controller.
Thanks
C:\IBF\CLI>adactrl show running
Cisco AD Agent adactrl -- version 1.0.0.32.1, build 598
Connection Error. Unable to connect to server: 0
An exception occured! Connection Error
For further information use:
adactrl help
C:\IBF\CLI>adactrl start
Cisco AD Agent adactrl -- version 1.0.0.32.1, build 598
Connection Error. Unable to connect to server: 0
An exception occured! Connection Error
For further information use:
adactrl help

Unable to connect to SMC Client system from SMC Server System

hi,
i have installed SMC 3.6.1. on Solaris 10 OS . The SMC agents are installed are all system but SMC Server is unable to communicate with Client systems. SMC Server System can Ping and Telnet all the SMC Client systems , but unable to connect from SMC .
Please guide how can resolve this problem
best regards,
Adeel Mehmood

Hi Adeel,
i have installed SMC 3.6.1. on Solaris 10 OS . The
SMC agents are installed are all system but SMC
Server is unable to communicate with Client systems.
SMC Server System can Ping and Telnet all the SMC
Client systems , but unable to connect from SMC .
Please guide how can resolve this problemSo, you can login to SunMC, but you're unable to make an icon for any of your Agents? Or you have icons you made bofre but when you click on them now you get errors?
If these are new Agents, do they have more than one netowrk interface? If so, they may have security information for the "other" network (the one the SunMC Server's not on). You can try manully specifying the correct network for one Agent and see if it helps:
http://forums.halcyoninc.com/showthread.php?t=2
Regards,
[email protected]
http://www.HalcyonInc.com
!! New !! : http://forums.HalcyonInc.com

VPN client unable to connect

I am unable to connect to our corporate internet with the client. It tries the primary and the backup addresses and then reports that the client timed out. Our IT is unable and/or unwilling to help troubleshoot. What can I do to find the problem? I am operating inside a local network over a wireless connection.

I too am having trouble maintaining my VPN Client connection.
We have a 515E PIX and Cisco VPN Client 4.8
Users will seemingly randomly loose access to our Network without any obvious reason.
Like today. I'm at home happily working over VPN for 6-hours, then I try to connect another computer up to work over VPN. My signal gets dropped and when I try to re-connect I get the request for Password but then it never connects. I have a few User IDs that I can use and none work.
I did as suggested in the previous post and have attached the Detailed log of one attempt to connect.
Mikka

Client unable to connect to Oracle 10g on linux

I have installed Oracle 10g on an Intel box running RedHat AS 3.0. The database installation was succesful but I am unable to connect to it from the client on my laptop running Oracle 10g client and Winfdows XP Pro. The server ip is 192.168.1.10 and I can ping it from the client:
C:\>ping attila.n3kje.net
Pinging attila.n3kje.net [192.168.1.10] with 32 bytes of data:
Reply from 192.168.1.10: bytes=32 time<1ms TTL=64
Reply from 192.168.1.10: bytes=32 time<1ms TTL=64
Reply from 192.168.1.10: bytes=32 time<1ms TTL=64
Reply from 192.168.1.10: bytes=32 time<1ms TTL=64
Ping statistics for 192.168.1.10:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Here is some info about the 2 environments:
[oracle@attila bin]$ uname -a
Linux attila.n3kje.net 2.4.21-9.0.1.ELsmp #1 SMP Mon Feb 9 22:26:51 EST 2004 i686 i686 i386 GNU/Linux
Server hosts file
======================================================
# Do not remove the following line, or various programs
# that require network functionality will fail.
127.0.0.1 attila.n3kje.net attila localhost.localdomain localhost
hostname output
======================================================
[root@attila root]# hostname
attila.n3kje.net
ifconfig output
=======================================================
[root@attila root]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:C0:9F:1D:0C:C8
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:13772171 errors:0 dropped:0 overruns:0 frame:0
TX packets:13748842 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1269613311 (1210.7 Mb) TX bytes:4065314800 (3876.9 Mb)
Interrupt:16 Base address:0xecc0 Memory:fe100000-fe120000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:5513840 errors:0 dropped:0 overruns:0 frame:0
TX packets:5513840 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:865454291 (825.3 Mb) TX bytes:865454291 (825.3 Mb)
Client TNSNAMES.ORA
======================================================
# tnsnames.ora Network Configuration File: C:\Oracle\product\10.1.0\Client_1\NETWORK\ADMIN\tnsnames.ora
# Generated by Oracle configuration tools.
ORACLE10G =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.1.10)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = DEV10G)
PRDSRR =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.1.10)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = dev10g)
Client SQLNET.ORA
======================================================
# sqlnet.ora Network Configuration File: C:\Oracle\product\10.1.0\Client_1\network\admin\sqlnet.ora
# Generated by Oracle configuration tools.
SQLNET.AUTHENTICATION_SERVICES= (NTS)
NAMES.DIRECTORY_PATH= (EZCONNECT, TNSNAMES)
Server TNSNAMES.ORA
======================================================
# tnsnames.ora Network Configuration File: /u01/app/oracle/product/10.1.0/db_1/n
etwork/admin/tnsnames.ora
# Generated by Oracle configuration tools.
DEV10G =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = attila.n3kje.net)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = DEV10G)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
Server LISTENER.ORA
======================================================
# listener.ora Network Configuration File: /u01/app/oracle/product/10.1.0/db_1/n
etwork/admin/listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = /u01/app/oracle/product/10.1.0/db_1)
(PROGRAM = extproc)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC))
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = attila.n3kje.net)(PORT = 1521))
Results from the TNSPING command issued at the client
=================================================================
C:\>tnsping prdsrr
TNS Ping Utility for 32-bit Windows: Version 10.1.0.2.0 - Production on 02-APR-2
004 09:26:11
Copyright (c) 1997, 2003, Oracle. All rights reserved.
Used parameter files:
C:\Oracle\product\10.1.0\Client_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)
(HOST = 192.168.1.10)(PORT = 1521))) (CONNECT_DATA = (SERVICE_NAME = dev10g)))
TNS-12541: TNS:no listener
C:\>tnsping oracle10g
TNS Ping Utility for 32-bit Windows: Version 10.1.0.2.0 - Production on 02-APR-2
004 09:26:38
Copyright (c) 1997, 2003, Oracle. All rights reserved.
Used parameter files:
C:\Oracle\product\10.1.0\Client_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)
(HOST = 192.168.1.10)(PORT = 1521))) (CONNECT_DATA = (SERVER = DEDICATED) (SERVI
CE_NAME = DEV10G)))
TNS-12541: TNS:no listener
C:\>
Trying to connect to the database from the server
==================================================
[oracle@attila bin]$ echo $ORACLE_SID
DEV10G
[oracle@attila bin]$ ./sqlplus system
SQL*Plus: Release 10.1.0.2.0 - Production on Fri Apr 2 12:22:29 2004
Copyright (c) 1982, 2004, Oracle. All rights reserved.
Enter password:
Connected to:
Oracle Database 10g Enterprise Edition Release 10.1.0.2.0 - Production
With the Partitioning, OLAP and Data Mining options
SQL> exit
Disconnected from Oracle Database 10g Enterprise Edition Release 10.1.0.2.0 - Pr
oduction
With the Partitioning, OLAP and Data Mining options
[oracle@attila bin]$ ./sqlplus system@dev10g
SQL*Plus: Release 10.1.0.2.0 - Production on Fri Apr 2 12:23:09 2004
Copyright (c) 1982, 2004, Oracle. All rights reserved.
Enter password:
ERROR:
ORA-12154: TNS:could not resolve the connect identifier specified
tnsping issued at the server
======================================================
[oracle@attila bin]$ tnsping dev10g
TNS Ping Utility for Linux: Version 10.1.0.2.0 - Production on 02-APR-2004 12:3
:44
Copyright (c) 1997, 2003, Oracle. All rights reserved.
Used parameter files:
/u01/app/oracle/product/10.1.0/db_1/network/admin/sqlnet.ora
TNS-03505: Failed to resolve name
What am I doing wrong?
Thanks
Renato

Ok, I was able to succesfully connect to the database from the client. I made the following changes to the sqlnet.ora, tnsnames and listener. Here are the changes I made:
sqlnet.ora
==============================
# SQLNET.ORA Network Configuration File: /u01/app/oracle/product/9.2.0.1.0/netwo
rk/admin/sqlnet.ora
# Generated by Oracle configuration tools.
# NAMES.DIRECTORY_PATH= (EZCONNECT)
NAMES.DIRECTORY_PATH= (EXCONNECT, TNSNAMES, ONAMES, HOSTNAME)
listener.ora
==============================
# listener.ora Network Configuration File: /u01/app/oracle/product/10.1.0/db_1/n
etwork/admin/listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = /u01/app/oracle/product/10.1.0/db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = DEV10G)
(ORACLE_HOME = /u01/app/oracle/product/10.1.0/db_1)
(SID_NAME = DEV10G)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC))
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.1.10)(PORT = 1521))
tnsnames.ora
===========================================
# tnsnames.ora Network Configuration File: /u01/app/oracle/product/10.1.0/db_1/n
etwork/admin/tnsnames.ora
# Generated by Oracle configuration tools.
DEV10G =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.1.10)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = DEV10G)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
Here is the new problem!
I start the dbconsole using the folowing command:
[oracle@attila bin]$ ./emctl start dbconsole
TZ set to US/Eastern
Oracle Enterprise Manager 10g Database Control Release 10.1.0.2.0
Copyright (c) 1996, 2004 Oracle Corporation. All rights reserved.
http://attila.n3kje.net:5500/em/console/aboutApplication
Starting Oracle Enterprise Manager 10g Database Control ........................
... started.
Logs are generated in directory /u01/app/oracle/product/10.1.0/db_1/attila.n3kje
.net_DEV10G/sysman/log
When I try and access it from the client I get the following error message:
"The database status is currently unavailable. It is possible that the database is in mount or nomount state. Click 'Startup' to obtain the current status and open the database. If the database cannot be opened, click 'Perform Recovery' to perform an appropriate recovery operation."
What am I doing wrong this time?
Your help would be greatly appreciated
Thanks
Renato

Remote Desktop Connection Client 9.3.9600 unable to connect to Server 2012 RDS via Gateway

Hi,
I have a Windows Sever 2012 R2 RDS environment with two Gateways servers configured in high availability mode (RD Web Access, RD Gateway, RD Connection Broker roles installed) and four Windows Server 2012 R2 RDS Session Hosts. The servers are all running
the most recent public server updates. With this configuration I when connecting externally using a Windows 7 computer with the older Remote Desktop Connection client (6.1.7601) I am able to connect without any problems however when I try connecting with a
newer client from a computer running Windows 8.1 and the 9.3.9600 client I am unable to connect.
At the moment a NAT rule is configured to pass 80/443 traffic to only one of the RDS gateway servers, I've removed our load balancer from the configuration for the moment to reduce the complexity.
No error is generated by the client when it tries to connect it just stops trying to connect after a while.
On the Gateways servers event logs for
Things I have looked into so far.
- I've double and triple checked the RDS configuration and checked it against one of my other clients configurations that is working and they are identical.
- Connecting from an older client version works fine.
I'm not sure what else can be checked does anyone have any ideas?

Hi,
1. What entries are you seeing in the RD Gateway's log? Event Viewer\ Applications and Services Logs\ Microsoft\ Windows\ TerminalServices-Gateway
2. How come you are not forwarding UDP port 3391 in addition to TCP port 443? It should work without UDP, but you will not have UDP support which is one of the benefits of RDP 8.0/8.1.
3. Are there any non-default group policy settings being applied to the servers and/or client PCs? To be clear, I'm asking if any changes have been made to the default local and domain security policies, group policy objects, new GPOs that may have
been added, etc., that are applicable to the servers and or client PCs.
-TP

Cisco 3850 Mobility Agent unable to connect clients

Similar Messages

Maybe you are looking for