Cisco 3925 Enhanced EtherSwitch Service Module
Hello all,
I have a Cisco 3925 router with a SM-ES3G-16-P Etherswitch module. In order for me to access it, I need to put an IP address on the phyiscal interface its attached to. Then I can access it via the service-module command.
My question is -- does it matter what address I give it? Does it need to be a legitimate management address on my network so that I can access it directly from another switch? Or do I always need to go through the router and issue the service-module command? If I do need to always go through the router, I should just be able to give it a 10.10.10.1 address and that should be enough, right?
Thanks for your help in advance,
Bobby Grewal
Thanks Reza...one more question. how does the switch module actually talk to the 3925 router? Through port 17 or 18? If so, do I need to configure those interfaces as routed ports within the same subnet? Or are they just trunks? All connections within the switching module would need to talk to outside devices.
Similar Messages
-
How to configure link between 2921 and SM-D-ES3G-48-P EtherSwitch Service Module
hi,
I can't do that like the procedure given by Cisco.
http://www.cisco.com/en/US/partner/docs/routers/access/interfaces/software/feature/guide/eesm_sw.html#wp1942894
Cisco Procedure :
interface gi10/0
ip address x.x.x.x x.x.x.x
service-module gigabitethernet 1/0 session
My result :
R2921-8CPITR-1(config)#int gi 1/1
R2921-8CPITR-1(config-if)#ip address 2.2.2.2 255.255.255.192
% IP addresses may not be configured on L2 links.
R2921-8CPITR-1(config-if)
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1.1 ?
% Unrecognized command
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1 ?
<cr>
R2921-8CPITR-1(config)#
the session is not possible also ?
R2921-8CPITR-1#service-module gigabitEthernet 1/1 sess
^
% Invalid input detected at '^' marker.
R2921-8CPITR-1#
The routeur said that it's not a L3 port, so how to configure it to allow communication between the 2921 and the card ?
Is there a bug with that version I'm in 15.1(4)M4 ????
R2921-8CPITR-1#sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 20-Mar-12 18:57 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
R2921-8CPITR-1 uptime is 19 hours, 21 minutes
System returned to ROM by power-on
System restarted at 16:00:45 GAB Fri Sep 14 2012
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FGL1618119E
6 Gigabit Ethernet interfaces
2 terminal lines
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2921/K9 FGL1618119E
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc None None None
data None None None
Configuration register is 0x2102
R2921-8CPITR-1#Same issue here.
I just waited a few minutes and the interface went down and back up, this time it was a L3 interface.
My guess is that it was booting the switch module IOS, and it detected it until it was fully booted:
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:26:52.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface Embedded-Service-Engine0/0, changed state to administratively down
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to administratively down
Apr 11 05:27:46.947: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
Apr 11 05:27:47.031: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
Apr 11 05:27:47.083: %LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state to administratively down
Apr 11 05:27:47.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down
Apr 11 05:27:48.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to down
Apr 11 05:27:49.283: %IP-5-WEBINST_KILL: Terminating DNS process
Apr 11 05:27:52.499: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up
Apr 11 05:27:53.087: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 04-Sep-12 16:50 by prod_rel_team
Apr 11 05:27:53.255: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Apr 11 05:27:53.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Apr 11 05:28:21.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Apr 11 05:29:22.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
Apr 11 05:29:22.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Router>en
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 unassigned YES unset administratively down down
GigabitEthernet0/1 unassigned YES unset administratively down down
GigabitEthernet0/2 unassigned YES unset administratively down down
GigabitEthernet1/0 unassigned YES unset administratively down down
GigabitEthernet1/1 unassigned YES unset up down
Vlan1 unassigned YES unset down down
Router#
Apr 11 05:29:46.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to upconf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int g1/0
Router(config-if)#ip add 1.1.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
Apr 11 05:30:09.046: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:30:10.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Router(config-if)#end -
Two etherswitch service module in same chassis
I need to connect two NME-X-23ES-!G in the same chassis (Cisco 3845) and i have the following troubleshooting:
1.- The numbers of the ports of both cards are identical. They are 1/0/2 to 1/0/24 for both modules. It would not have to change the first number depending on in which slot is inserted the card?
2.- How I can configure the router for being able to arrive at both modules with the same VLAN. If I configure Etherchannel I cannot configure a IP address for the interface g1/0 or g2/0. If I do not have IP address I cannot make a session to switch module.
3.- If I use the connect command I cannot use slot number 1 of routers because it leaves a message which not this supported. What I can do for being able to use it?Hello,
I think you need to configure stacking for both modules, here is what CCO says:
Configuring Stacking
Stacking is the connection of two switch modules resident in the same chassis so that they behave as a single switch. When a chassis is populated with two switch modules, the user must configure both of them to operate in stacked mode. This is done by selecting one port from each switch module and configuring it to be a stacking partner. The user must then connect with a cable the stacking partners from each switch module to physically stack the switch modules. Any one port in a switch module can be designated as the stacking partner for that switch module.
Beginning in privileged EXEC mode, follow these steps to configure a pair of ports on two different switch modules as stacking partners.
SUMMARY STEPS
1. interface fastethernet interface-id
2. no shutdown
3. switchport stacking-partner interface FastEthernet partner-interface-id
4. exit
5. interface fastethernet partner-interface-id
6. no shutdown
7. end
HTH,
GP -
Service-module g2/0 session access fails
I did not add a vty/telnet password when I initially configured my NME-X-23ES-1G switch in my 3825 router. Now, of course I can not telnet to the switch, but the session access fails as well. How do I recover this?
Config in 3825:
interface GigabitEthernet2/0
ip address 106.40.x.x.255.255.0
Attempt to access switch module:
3825_Router2#service-module g2/0 sess
Trying 106.40.77.254, 2130 ...
% Connection refused by remote hostThe default configuration for Cisco EtherSwitch service modules allows an end user to recover from a lost password. The password recovery disable feature allows the system administrator to protect access to the switch password by disabling part of this functionality and allowing the user to interrupt the boot process only by agreeing to set the system back to the default configuration. With password recovery disabled, the user can still interrupt the boot process and change the password, but the configuration file (config.text) and the VLAN database file (vlan.dat) are deleted.
The following document shows how to recover from a lost or forgotten password.
http://www.cisco.com/en/US/products/hw/modules/ps2797/products_feature_guide09186a0080415bae.html#wp1776357 -
when i show service-module ids-sensor 1/0 status
i have the following output
Service Module is Cisco IDS-Sensor1/0
Service Module supports session via TTY
Service Module is failed
Service Module status is not available
what is the problem and how can i recover it?
note i make restart for the service module by the command
service-module ids-snsor 1/0 reset
but it remain failed
please help me as soon as possibleYou've powered off and re-seated the card and this was working at one point? Beyond that, if there is no output from the CUE console (while connected to the module via "service-module service-engine 0/1 session"), then the module is likely defective.
-
Service Module is trying to recover from error - Please help
HI Guys
I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status
I have checked the troubleshooting pdf and says might be possible hardware error ,but before i go down that road would like to know if any of the engineers have solved this problem
Info about router and module is as follows
Router#service-module wlan-controller 1/0 status
Service Module is Cisco wlan-controller1/0
Service Module supports session via TTY line 66
Service Module is trying to recover from error
Service Module status is not available
Router#
Trying to reset Service Module wlan-controller1/0
*Mar 28 21:49:06.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface wlan-controller1/0, changed state to down
*Mar 28 21:49:26.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface wlan-controller1/0, changed state to up
Router#
Router#service-module wlan-controller 1/0 status
Service Module is Cisco wlan-controller1/0
Service Module supports session via TTY line 66
Service Module is trying to recover from reset/shutdown
Service Module status is not available
sh version
Router#sh ver
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T17, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 24-Jan-12 07:41 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
Router uptime is 28 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-advipservicesk9-mz.124-15.T17.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.
Processor board ID FCZ0932701R
2 FastEthernet interfaces
1 Serial(sync/async) interface
1 terminal line
1 Virtual Private Network (VPN) Module
1 cisco Wireless LAN Controller(s)
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
Router#HI Guys
And it gets worse I am now getting the following error
Router#service-module wlan-controller 1/0 status
Service Module is Cisco wlan-controller1/0
Service Module supports session via TTY line 66
Service Module is failed
Service Module status is not available
regards Thags Govender -
I'm trying to install a MGBSX1 into the Cisco 3925 but it's doesn't seem it's detecting it for some reason.
I've changed media type and I've tested with another SFP module (GLC-SX-MM) which works fine.
Am I missing a command to enable this type of module on the Cisco 3925?
ThanksHi,
Looking at the SFP compatability table for 39XX series routers.
http://www.cisco.com/c/en/us/products/routers/3900-series-integrated-services-routers-isr/relevant-interfaces-and-modules.html#formfactor
The MGBSX1 is NOT mentioned
Looks like the MGBSX1 is only compatable with the Small Business switch family.
http://www.cisco.com/c/dam/en/us/td/docs/interfaces_modules/csbna/mgb/quick_start/guide/Optical_Module_QSG_en-US.pdf
Regards
Alex -
Cisco 3560 service module failed state
Hi Expert,
My office has a Cisco 2911 ISR router, we installed a 3560 service module 16P on it.
But I use command "sh ip int bri" in 2911 router when we finished installation.
The result shows that the interface Gi 1/1 doesn't work, I have try to re-install SM 16P twice, the result is the same.
The normal 2911 ISR + 3560 SM 16P show as below,
2911#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES NVRAM administrativelwy down down
GigabitEthernet0/0 xxx.xxx.xxx.xxx YES manual up up
GigabitEthernet0/1 xxx.xxx.xxx.xxx YES NVRAM up up
GigabitEthernet0/2 unassigned YES NVRAM down down
GigabitEthernet1/0 xxx.xxx.xxx.xxx YES NVRAM up up
GigabitEthernet1/1 unassigned YES unset up up
The BAD 2911 ISR + 3560 SM 16P show as below,
2911#sh ip int brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 xxx.xxx.xxx.xxx YES NVRAM up up
GigabitEthernet0/1 unassigned YES NVRAM administratively down down
GigabitEthernet0/2 unassigned YES NVRAM administratively down down
GigabitEthernet1/0 unassigned YES NVRAM administratively down downHi Krishnendu,
I understand what you mean, I have done this work for assign Gi 1/0 an IP address, and then using command "service-module gi 1/0 session" to enter the service-module to configure it at all.
But I just want to know what is the Gi1/1 interface used for?
I use command "sh cdp nei" on others 2911 ISR + 3560 service module, all of the has the Gi 1/1 interface, and 2911 router using Gi 1/1 interface connected service module Gi 0/17. And Gi 1/1, Gi 0/17 is configured with "trunk interface".
I'm wondering whether my 2911 router Gi 1/1 has some physics error? or maybe it has another command to to "OPEN" the Gi 1/1 on 2911?
The "normal" switch display as below,
rtr001#sh cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
swt000.nneas.net
Gig 1/0 129 R S I SM-ES3G-1 Gig 0/18
swt000.nneas.net
Gig 1/1 129 R S I SM-ES3G-1 Gig 0/17
Thanks in advance,
BR Frank -
Cisco SSL Services Module (on 6500)
Hi all,
A customer has asked me a few questions on an SSL Services Module they have (that we haven't sold and have little experience with). I've been reading the documents, but I have some questions and things to verify...
As I can understand, they already have services and trustpoints configured on the module, but with certificates created with a previously-existing internal AD-integrated CA. Now, they want to switch their services to run a certificate they've obtained from a legitimate CA.
1) They are trying to import the new certificate with copy-paste method, through the terminal. As far as I can see, both the server certificate and the CA certificate issuing the server cert. should be in base64 encoded for this to work, right? Or, can we import somehow PKCS or PEM certs thorough the terminal?
2) They would like to use a wildcard certificate for a few of their servers/services they publish. (Like, instead of getting 3 different certificates for service1.domain.com, service2.domain.com and service3.domain.com, they'd like a certificate for *.domain.com which would work for all of the 3 services.) Is this possible? Should they need to change their configuration? (Now I understand that they have different trustpoints, certificates and service configurations for each of the servers...)
I'd really like if some good soul with experience could shed a little light on this...
Or, any leads on documentation (that I may have missed) would also be appreciated.
Thanks in advance,
EmreGood day Emre-
For question 1 - You can import PEM base64 certificates via the terminal only, all other types need to be loaded over tftp/sftp/ftp.
For question 2 - There is nothing special about how the SSLM handles the Issed To field in a certificate, it doesn't matter if it is specifc or wildcard. Multi domain certificates are also ok (using a Subject Alternative Name field.) The only thing I can think of here in terms of a difference is you might have less trustpoints and configuration on you SSLM since you no longer require multiple server certificates.
Outiside of your direct questions, make sure you upload the root and intermediate(s) into the SSLM. It has to be able to complete the SSL chain from server to root in order to operate.
Regards,
Chris Higgins -
Firewall service module vs ASA
Hi
Someone told me that the cisco firewall service module of 6500 has poor performances compared to ASA
What do you recommend as a core firewall (to protect internal servers): ASA or firewall service module ?
thanksHi,
We are using 5 FWSMs at the moment but are moving away from them to ASA5585-X models.
I wouldnt suggest going to FWSMs anymore at this point if you have any plan on having support for new features.
End Of Life and End of Sale Notice
http://www.cisco.com/en/US/prod/collateral/modules/ps2706/eol_c51-699134.html
The follower for the FWSM is the ASA Service Module which supports the newer softwares (while the FWSM doesnt). Heres a link to a document about the ASASM
http://www.cisco.com/en/US/prod/collateral/modules/ps2706/ps11621/data_sheet_c78-672507.html
Also you could always consider a separate ASA models. Here are links to both the orignal ASA 5500 series and new ASA 5500-X series
ASA 5500 Series
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80285492.pdf
ASA 5500-X Series
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/at_a_glance_c45-701635.pdf
I guess the question for you is what are the requirements for the device regarding performance. All of the above documentation should give you a clue about which model might be the best for you.
- Jouni -
VPN service module choice 7600-SSC-400 vs. SPA-IPSEC-2G
Need to decide between the two VPN service module: 7600-SSC-400 and SPA-IPSEC-2G for a 6509 sup 720 3bxl. Not sure what is the difference and couldnt find too much info just searching the internet. What would be the benefits of one or another?
Hello,
You will need both. The 7600-SSC-400 is the carrier module of the SPA-IPSec-2G.
There is more information on this via the following link:
http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/6500series/76ovwvpn.html
Warm Regards,
Rose -
ASA Service module shut down and on automatically
hello,
i have a asa service module which is inserted on 6509 chassis.
This morning when i came to the office i have noticed my asa service module was restarted at last night but 6509 was up.
one more thing we dont have failover.only have single asa service module.
ASA SM version is 8.5
below is the failover history and details
ciscoasa up 17 hours 11 mins
------------------ show crashinfo ------------------
No crash file found.
------------------ show failover history ------------------
==========================================================================
<--- More --->
From State To State Reason
==========================================================================
14:28:40 UTC Apr 7 2013
Not Detected Disabled No Error
can any one tell me why this happend.
thanks in advanced
KhemHi,
Would seem to me that it would be best to check this through Cisco TAC to determine the cause.
It would seem though that no Crashinfo file was generated so thats kinda strange.
You should be able to confirm if the ASASM is set to save a crashinfo file with the command "show crashinfo save"
- Jouni -
ASA Service Module on 6500 montoring console session
We have 6500 with ASA Service Module
On 6500 how can we configure so that if someone logs in to the ASA Service Module and reboots the firewall we can have logs of it in syslog of switch .
Thanks for helpI hate to answer my own posts, but here it is. TAC tells us that there are 2 choices to make this work. Apparently the way that worked on an ISR and ISRG2 does not work on the 4000 series routers. I guess that's progress.
Option 1. Use a physical cable to connect one of the router's interfaces to one of the etherswitches interfaces and treat it just like the etherswitch is a seperate physical switch. I'm sure there is a use case for that but I'll not cover that here.
Option 2. Use the "service instance" feature on the router's internal interface to bind it to a new "BDI" virtual interface on the router. This is what we'll do.
On our router ethernet-internal 1/0/0 maps to Gi0/18 on the etherswitch, all internal to the box. The router will be10.0.0.1 and the switch will be 10.0.0.2.
Router:
interface Ethernet-Internal 1/0/0
service instance 1 ethernet
encapsulation dot1q 50
rewrite ingress tag pop 1
interface BDI 1
mtu 9216
ip address 10.0.0.1 255.255.255.0
Switch:
interface Gi0/18
switchport trunk vlan allowed 50
switchport mode trunk
vlan 50
name Egress vlan
interface vlan 50
ip address 10.0.0.2 255.255.255.0
ip route 0.0.0.0 0.0.0.0 10.0.0.1
Then there are a million ways to design and configure the switch as a normal 3560X switch but that's beyond the scope of my question. -
RME 4.3.1 Inventory collection failing for cisco 3925
Hi,
I've a customer having LMS 3.2 and RME 4.3.1. He has 14 Cisco 3925 routers out of which inventory collection for 2 fails.
Router IOS is: c3900-universalk9-mz.SPA.150-1.M.bin".
Can someone suggest what might be going wrong? Attached is the IC_Server log file for reference.
Thanks in advance,
inner_silenceHi,
Here are the exception found from the log :-
[ Fri Mar 18 16:28:24 EDT 2011 ],ERROR,[Thread-17],com.cisco.nm.rmeng.inventory.ics.core.CollectionController,729,Exception for device 10.103.251.12 is
java.lang.reflect.InvocationTargetException
at sun.reflect.GeneratedMethodAccessor12.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at com.cisco.nm.rmeng.inventory.ics.core.CollectionController.run(CollectionController.java:719)
at java.lang.Thread.run(Thread.java:595)
Caused by: com.cisco.nm.xms.xdi.ags.system.CollectionFailed: java.lang.StringIndexOutOfBoundsException: String index out of range: 2
at com.cisco.nm.xms.xdi.pkgs.LibInventory.EnergyWise_HelperMethods.getDeviceEnergyWise(EnergyWise_HelperMethods.java:72)
at com.cisco.nm.xms.xdi.pkgs.SharedInventoryCatIOS.EnergyWiseAGI_ENERGYWISE_Mib.g$eval(EnergyWiseAGI_ENERGYWISE_Mib.java:51)
at com.cisco.nm.xms.xdi.ags.EnergyWiseAGI.g$eval(EnergyWiseAGI.java:21)
at com.cisco.nm.xms.xdi.SdiEngine.initAndEvalAGIs(SdiEngine.java:383)
at com.cisco.nm.xms.xdi.SdiEngine.request(SdiEngine.java:309)
at com.cisco.nm.xms.xdi.SdiEngine.getDevRepr(SdiEngine.java:302)
at com.cisco.nm.rmeng.inventory.ics.core.CollectionController.run(CollectionController.java:539)
... 1 more
[ Fri Mar 18 16:28:24 EDT 2011 ],ERROR,[Thread-17],com.cisco.nm.rmeng.inventory.ics.core.CollectionController,761, Collection failed for the device : 63
com.cisco.nm.xms.xdi.ags.system.CollectionFailed: java.lang.StringIndexOutOfBoundsException: String index out of range: 2
Kindly check if the your device is running the required IOS on the device as per the device supported list :-
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html
There are two 3925 listed with different versions :-
Cisco 3925 Integrated Services Router --> 1.3.6.1.4.1.9.1.1042 --> 15.0(1)M [RME]. if this is your device then upgrade to
3925 to 150-1.M2
and
Cisco 3925E Integrated Services Router --> 1.3.6.1.4.1.9.1.1144 --> 15.1(1)T
Thanks,
Gaganjeet
If this post answers your question, please click the "Correct Answer" button -
CUE "Service Module is failed"
Dears , i am getting this error on CUE .I reload the router but result is same .what should i do now?? ..
#service-module service-engine 0/1 status
Service Module is Cisco Service-Engine0/1
Service Module supports session via TTY line 258
Service Module is failed
Service Module status is not available
Regards,
ShibYou've powered off and re-seated the card and this was working at one point? Beyond that, if there is no output from the CUE console (while connected to the module via "service-module service-engine 0/1 session"), then the module is likely defective.
Maybe you are looking for
-
Trying to upgrade from 10.4.11 to 10.5.8
I'm working on restoring my computer after replacing a bad hard drive (G5 see below)... Machine Name: Power Mac G5 Machine Model: PowerMac7,3 CPU Type: PowerPC G5 (3.0) Number Of CPUs: 1 CPU Speed: 1.8 GHz L2 Cache (per CPU): 512 KB Memo
-
How to deal with complex SOAP responses when calling web services ???
Hi all, I have an issue when calling a web service that returns a complex SOAP response message. With simple responses (e. g. array of strings) it worked. I created the PDF as an Interactive form with Livecycle Designer 8.2. The Javascript looks like
-
hi , my iMac 20'' with iLife '08 bought in december 2008 can't see the Canon MV400 camcorder ( I use the firewire 6 pin to mac and 4 pin to camera ; I have 2 port on my iMac: FireWire 6 pin and FireWire 800); on a Mac+iLife '06 of my friend the camer
-
1. How to display hiredate from an emp table where deptno is 20 as dd/mon/yyy? My Solution:Select hiredate from emp where hiredate ('dd/mm/yyyy') and deptno=20; 2. How to display ename from emp table who joined the company other then 1981? My Solutio
-
TS1717 hi , i have been playing draw something on my iphone 4s
Hi, I have been playing draw something on my ophone 4s successfully until today when I tried to access the draw free app the screen was/is black please help i m addicted to the game thanks Jeff