Cisco 3925 router with an ATM E3 card that never goes down!

Hi all,
We a Cisco 3925 router with an ATM E3 card (NM-1A-T3/E3) configured as below with 1 PVC. we see that the ATM subinterface we created for the PVC never goes down! not even when the WAN link is down! The problem with this is we are tracking the line protocol of the ATM sub interface to have VRRP failover to standby router. But because of this issue only BGP goes down whenever the WAN is down & line-protocol of the Subinterface remains up, the failover never happens & site is down. We can configure VRRP to track reachability of a BGP route as workaround but I would like an explanation or troubleshooting steps to check whats the trouble with current setup?
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(2)T4.1, MAINTENANCE INTERIM SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 30-Aug-11 08:44 by prod_rel_team
card type e3 1
interface ATM1/0
 description Link to PE
 mtu 1500
 bandwidth 34010
 no ip address
 no ip proxy-arp
 logging event subif-link-status
 no atm ilmi-keepalive
 no atm enable-ilmi-trap
end
interface ATM1/0.101 point-to-point
 description PVC to MPLS PE
 mtu 1500
 bandwidth 2500
 ip address a.b.c.d 255.255.255.252
 no ip proxy-arp
 ip flow monitor FMforIP4in sampler ata1to100 input
 ip flow monitor FMforIP4out sampler ata1to100 output
 ip nat outside
 ip virtual-reassembly in
 no atm enable-ilmi-trap
 snmp trap link-status
 pvc 1/101
  vbr-nrt 8192 8192 1
  vc-hold-queue 2048
  oam-pvc manage
  oam retry 3 5 1
  oam ais-rdi 15 3
  encapsulation aal5snap
  protocol ip inarp
  queue-depth 5 3
  service-policy out Edge_Queueing
end
Thanks a lot in advance!

Your router has some configuration on it already and it would help us give you better advice if we knew what is already in the configuration. So would you post the output of show running-config (if there is sensitive information like addresses and passwords you can mask them out.
Changing the configuration register was a good start. I have a couple questions/observations that may help you get started. I notice what appears to be the same public IP address on Gig0/0 and on multilink. Did you get that address from your ISP? If so what kind of connection do you have to the ISP?
In your description you tell us that Gig0/0 is connected to a small switch, which I assume is for the LAN of your network. But that also is the interface where the public address is configured. So I am confused whether this interface is for LAN or for connecting to the ISP. Can you clarify this?
HTH
Rick

Similar Messages

  • Configuring IP SLA in cisco 3925 router.

    HI Team.we need to configuring IP SLA in cisco 3925 router with c3900-universalk9-mz.SPA.151-4.M4.bin ios. For Monitoring purpose. Earlier we have used the rtr command for the same. Now we are going with new Cisco 3925 router. with the above mentioned IOS. Pls suggest whether we can configure the IP SLA in the router with Licence. Or We need to buy the licence for the ame.
    Posted by WebUser Ramkumar Selvaraj from Cisco Support Community App

    Hi
    I think the command has been updated - rather than 'rtr responder' it's now 'ip sla responder'.
    I don't believe you need any particular feature set.
    Also, this is a 'Contact Center' forum - you would get more responses in other places.
    Regards
    Aaron HarrisonPrincipal Engineer at Logicalis UK
    Please rate helpful posts...

  • Cisco 2600 router with 4A/S module can be terminal server

    I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports? Thanks a lot

    The commands mean that R1's console is connected using the first RJ-45 cable and is available on port 2001, R2's console is connected using the second RJ-45 cable and is available on port 2002 and so on. Remember that the ports are numbered as 2000 plus the line number. Hence, the first port is 2001. If you have more than eight devices and have connected a second CAB-OCTAL-ASYNC cable then you need to add a similar configuration line with the port numbers starting from 2009 till 2016.
    In your configuration u configured 9 ports. So please add second cable for another 8 ports.
    To connect to the console of a device, telnet to the terminal server router's loopback address and specify the port number associated to the device. For example, to connect to console of router R1 (from our example) type telnet 192.168.12.1 2001 in the Run dialog box from your PC.
    For further information click the below url
    http://www.cisco.com/public/technotes/smbsa/en/us/internet/config_cisco_router_term_server.html#trouble

  • How many numbers of GRE Tunnels are supported on Cisco 3925 router?

    Hi...
    I would like to know that.......
    How many numbers of GRE Tunnels are supported on Cisco 3925 router?
    Thanks....

    This is what I found in my search:
    There may be factors such as memory constraints that will place practical limits on how many tunnels you can support. But there is also a hard limit on the number of tunnels that you can configure. That limit is based on the limitation of the number of IDBs supported by your router. The IDB is the Interface Descriptor Block and each interface (physical, or tunnel, or loopback, or whatever) requires an IDB. The number of IDBs will vary by platform and sometimes by release level of the code that you are running. You can use the privileged command show idb to see what the limitation is on your router. On the 1841 router that I just checked the limit on IDB is 1200 (which is a pretty large number - I believe that you would encounter other limits on performance or on size of configuration before you exhaust the IDB limit).
    https://supportforums.cisco.com/thread/2007932
    Hope it helps.
    Jatin Katyal
    - Do rate helpful posts -

  • Using this router with a verizon cell card

    i have a wrt54g router can i set this up for use with a verizoc cell card that plugs in to my usb port

    Hi,
    A friend of mine hooked up our Linksys router so that we could use it with our Verizon cell card and it worked great for a couple of days and then all of a sudden
    it quit working.  Now I can't have both computers online at the same time and I need to find out what the problem is.  Unfortunately my friend lives about 100 miles from me!
    So, the answer is YES it can be done.  Good luck!
    Kathy
    PS.  I love my Verizon card, don't you?  We travel in our motor home sometimes and it's great to have Internet access while on the road!

  • HT4199 I have a new iPhone 4s.  I have a home wi-fi network using Cisco Linksys2000 router with all settings per this article - phone will not see network if set to 5 GHz channel width - solution??  2.4 works but is not optimal with other devices in home

    I have a new iPhone 4s.  I have a home wi-fi network using Cisco Linksys2000 router with all settings per this article - phone will not see network if set to 5 GHz channel width - solution??  2.4 works but is not optimal with other devices in home (computers; tivo).  Have others seen this?  Any advice is much appreciated.

    Stephen Spark is right - your best alternative is to use a simultaneous dual band wireless router like the AirPort Extreme. Your Cisco Linksys2000 is not a dual band router, meaning that it will be constrained to operate at the slowest speed of all the devices on your network.
    The AirPort Extreme's dual networks will support all your 802.11n devices as well as all your 802.11b/g devices on both the 2.4 and 5 GHz frequencies simultaneously.

  • How do i set up my pre owned iphone 4 with my giffgaff sim card that was used in my iphone 3gs

    how do i set up my pre owned iphone 4 with my giffgaff sim card that i have been using in my iphone 3gs
    My 3Gs is on its last legs.... I've just bought a second hand iphone 4 which is unlocked......I put my giffgaff sim card in the new phone and it says activation required ......then it asks me for a passcode???  PLEASE HELP!!!! I have no idea what to do xx

    You need to connect the phone to iTunes and then try activating it from there and restoring it as new.
    If you have further problems and especially as the iPhone you have bought is second hand, it could be that it is not unlocked.  Are you sure that it is?  If not, then you'll need to speak to the person that you purchased it from.

  • Cisco 2811 Router with 3 ADSL card and load balancing

    Dear All,
    I have few queries:
    1. Does Cisco 2811 Router support 3 ADSL card?
    2. We are the ISP. I want to do load balancing with 3 dsl
    line on Cisco 2811 Router.
    Please send me the linke for this configuration.
    Thanks/Regards
    Atul

    hi
    In 2811 you have 4 HWIC and 1 NME you can install 1-port ADSL WAN Interface Cardon the HWIC slots.
    Also just enable 3 default (equal cost) routes towards the interfaces which will take care of the load balancing.
    if you need more info and inputs do post out with ur requirements along with network topology in place at present..
    regds

  • I have a Cisco 2811 router with a NM-2FE2W module installed, it shows up in Sh diag but it says it is disabled?

    I installed NM-2fE2W module on the 2811 router on the bottom which I guess is slot 1.
    It shows up in Sh diag as disabled how can I correct this? I have the same IOS as on packet tracer 6.1 ver 12.4 (15)T. I have tried upgrading the IOS and downgrading IOS.
    Slot 1:
    Unknown (type 919) Port adapter
    Port adapter is disabled
    Port adapter insertion time unknown
    EEPROM contents at hardware discovery:
    Hardware Revision : 1.0
    Top Assy. Part Number : 800-21601-02
    Board Revision : B0
    Deviation Number : 0-0
    Fab Version : 01
    PCB Serial Number : JAE0831RLPQ
    RMA Test History : 00
    RMA Number : 0-0-0-0
    RMA History : 00
    Product (FRU) Number : NM-2FE2W-V2=
    EEPROM format version 4
    EEPROM contents (hex):
    0x00: 04 FF 40 03 97 41 01 00 C0 46 03 20 00 54 61 02
    0x10: 42 42 30 80 00 00 00 00 02 01 C1 8B 4A 41 45 30
    0x20: 38 33 31 52 4C 50 51 03 00 81 00 00 00 00 04 00
    0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
    0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
    0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
    0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
    0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    Don't know for sure what's the cause of your issue, but some hardware requires a minimum IOS version and/or feature set to utilize.  Also, some hardware requires additional configuration commands to enable the hardware.

  • Cisco SRP520 Router with NexStar FX NAS

    How do i get the Cisco SRP520 Router to assign the external IP to my NexStar FX Nas,
    i have a Harddrive in the NexStar FX Nas,and the files is setup to FTP, but i cant access it from a diffrent network, if i'm connected to the network it works but asoon as i use a diffrent network it doesnt pick up... i also have a working dyndns account setup on router can i use the dyndns account to ftp?
    for Example: ftp://site2.dyndns.org

    Hi Ruan,
    Just create a port forwarding rule for application you wish to expose to the internet.
    Network Setup > NAT > Port Forwarding.
    The Admin Guide has more detail if you need it.
    Andy

  • How do I download an app that is over 50mb via itunes on my computer with a app store card that has already been redeemed

    I was trying to download plants vs zombies on my iphone but it wouldnt let me saying that the app was over 50mb and that you needed to install it using itunes on your computer. So I tried to do the same thing on my computer by using my app store card to cover the purchase but as the code had already been redeemed it wouldnt let me. Can I get the app using my already reddemed app store card or is that not possible? I will be very grateful for any suggestions or help!

    If you have already purchased it on your iphone, and it simply wasn't able to download, then open itunes on your computer and click Store>Check for Available Downloads

  • Does anyone know how to make my old blackberry curve 8900 work with my new sim card that has been set up on my 9360?

    i hate my new blackberry 9360  it never gave me a days hassle and i want to use it for the remainder of my contract as the 9360 is just a pain and full of problems and no matter what i do i cannot get an alternative phone despite the fact that i am a high spender with loyalty of over 10 years to my supplier.  i do not want to use a fixed second hand phone.  the reason we get a new phone is emphasis on new.
    Solved!
    Go to Solution.

    back to using a proper phone - please make some more blackberrys like the old 8900 as it is a sturdy, reliable phone.
    so my paid for brand new but got second hand repaired 9360 will sit in a box for two years.

  • Can I use Apple Pay with a Chinese Credit Card that is MasterCard or VISA in the United States?

    The credit card is issued by a Chinese Bank but it's MasterCard or VISA.

    A list of participating banks is on this page. I don't see any chinese banks.
    http://www.apple.com/iphone-6/apple-pay/

  • I have a Nook Color with a 16GB N2A card that runs Android 2.3.4. It should be able to run the new Firefox. However, the Android Market says it's not compatible. I'd like to be able to at least download and install it. Where can I download it?

    Maybe you can change the Market so that we can try it?
    I'm not sure whether this would be considered "rooted" since it's not permanent, but I think it should. There are several of us at the N2A form who are interested.
    Thanks.

    You can find a link to download Firefox for Android directly from our FTP server on this page: https://wiki.mozilla.org/Mobile/Platforms/Android

  • A computer with the latest tech..that let me down...

    [size=13]What I didint know about my intel.....and 1.4V AGP [/SIZE]
    Hi everyone,  I thought I'd post this message to the techies here so you don't make the same mistake I did on my new computer, And maybe give me a little advice...
    I'm a huge gamer.  I wanted the fastest possible combination of speed and technology I could find to make a super machine.  I purchaced a lightning combination, as follows....
    Intel 3.06 processor
    (850E family based Mother board)
    2 GIG 32bit Pc3200 Rambus
    new Radeon 9800
    2x (striped) Seagate Cheetah SCSI @15000RPM
    The system accesses the internet, Os, and non-graphical applications with almost godlike speed. But for open GL...well it's terrible.
    The computer crashes constanly.  It seems that 850 Intel chipsets just suck under graphical stress and it's because of the 1.4V AGP slot on every board.
    It's not a driver problem. I've had a team of 6 personnel disect the computer, specilising in finding a drivers that are compatible with device to device.
    Here's my questions for you guys and gals.
    1.  Does any of you MSI guys know anything about crash problems with a computer of this spec?
    2. Do any of you know anything I don't about Rambus and 1.4 AGP instability?
    3.  Does anyone know a fix....or anything I could do at this point to get back into open GL applications??
    Thanks for listening and I advise people who recommend a rambus solution to Gaming performance...
    Reasearch,reasearch,reasearch............. ?(  

    What do you mean by '1.4V AGP' ??
    Are you referring to electric current? Then you are dead wrong, current AGP cards need a minimum of 1.5 Volts.
    Any why-o-why are you using openGL for games? The 9800 series are blazing fast ... in D3D. OpenGL (and its decendant Glide) are not supported by most recent games.
    The 850/850E are one of the most powerfull solutions to building a performance system, only surpassed by the 865/875 chips.
    A friend of mine owns a 850E in combination with a 9700pro and has no problem at all. Maybe your board and/or graphic card are not 100%. No way of telling really, so i'm afraid i can't help you any further.
    Best of luck to you though, hope you solve the problem.

Maybe you are looking for

  • Problem in RFC Lookup

    Hi, I am performing RFC lookup using Communication Channel. I have used a function called "Z_MATERIAL_DETAILS". Input to this function is "MATERIALID" and Output of the function is "MATNR". I am using the following code in my UDF for performing looku

  • Apple ID link question

    My iPhone is associated with my husband's apple ID. How do I link it to my newly created apple ID?  Will this screw up my husband's ID or account?

  • Safari wont load page until i open a new tab?

    this happens on my new macbook pro and my super old mac mini when i open a new safari window and it goes to "top sites" then google search or input a web address it doesn't actually start searching or going to the web address until i open a new tab.

  • How netbeans starts you off...

    When I start a new project in NetBeans, it starts me off with the following code. public class Main {      /** Creates a new instance of Main */      public Main()       * @param args the command line arguments      public static void main(String[] a

  • No data found from start index 2 to end index Error

    I'm trying to import a .csv and I keep getting this error  when I press the Next button: No data found from start index 2 to end index I know it is because my Date column in my csv, because when I take it out I don't get the error I have the date in