Cisco 4507R problem

I have started to see the problem for couple days where some hosts connected to 4507R stopped responding to ping and I saw huge latency upto 400msec. (In normal cases it is 1 msec becuase they are directly connected hosts. I couldn't find anythiing in the logs or interface errors but show proc cpu history and found that CPU went up to 100% in last 60 sec. Anyone know why it is doing this? Do I need a reboot?
Thanks.

Hi Bobby
I'm pinging from a different host which is directly connected to this swtich and our monitoring system (HpOV also on the same vlan)sends pages/email when it looses pings. The highest process I see on show proc cpu is
26 3609955722129699394 169 9.03% 9.79% 9.92% 0 Cat4k Mgmt HiPri
27 30077935764176720830 720 8.47% 7.57% 7.61% 0 Cat4k Mgmt LoPri
but when I do show proc cpu histroy I see about 99% spike but that doesn't show which process, here is the capture
xec-4507-25#sh proc cpu history
1111122222222221111111111111111111122222333331111122222111
6666600000000007777799999777777777788888111115555511111666
100
90
80
70
60
50
40
30 **********
20 **********************************************************
10 **********************************************************
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per second (last 60 seconds)
4444554444444455444443435343434375534343434352424342429942
6644889955996688224442328852534394512442231368995366779978
100 **
90 **
80 * **
70 * **
60 ** ** * * * * **
50 ** ************ * * * *** * * * * * ***
40 ********************* * *** * * *** * * * * * * * * * *#*
30 ********************************##********************##**
20 ##########################################################
10 ##########################################################
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per minute (last 60 minutes)
* = maximum CPU% # = average CPU%
9977787677655587777777766675556677877787666555777776777766755586677777
9571002931794143410410487627389561511711952155461009150261467110632133
100 **
90 ** *
80 *** * * * * ** * * *
70 *********** ************* ************ *********** * * ******
60 ************ ************** ************** ***************** ********
50 **********************************************************************
40 **********************************************************************
30

Similar Messages

  • VSS on cisco 4507R+E with sup8-E

    Hi folks,
    I need to configure VSS on cisco 4507R+E switch with SUP8-E,but the problem is that as per the latest relase notes VSS is not supported on sup8-E. 
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/release/note/OL_32143-01.html
    Can someone advise me how to proceed?

    Hi,
    The links coming from cpe1 and cpe2 can be bundled and made layer3 port channel on VSS swirtch?
    No, the link can't be in a Porchannel as cpe-1 cpe-2 are 2 different devices. If cpe-1 and 2 were for example Cisco 3750 stacked, then yes, you could put both links in a Portchannel on the 3750s and also on 4500 (VSS).
    on VSS switch : 172.16.10.6/29 (port channel)
    cpe1: 172.16.10.2/29
    cpe2: 172.16.10.3/29
    HSRP virtual IP: 172.16.10.4/29
    All above statements are correct.
    Can you eloborate how I can use dot1q encapsulation for this scenario?
    Let assume cpe-1 and cpe-2 are Cisco 3845 routers. In this case, you can simply create a sub-interface an each device connecting to the VSS with dot1.q
    for example on cpe-1
    interface gi0/0
    interface gi0/0.10
    ip address 172.16.10.2/29
    encapsulation dot1q 10
    the same thing on cpe-2 except a different IP address.
    Now you create vlan 10 with dot1q encapsulation on the 4500 and add it to what ever interfaces that are connecting to the cpes with an ip address on th svi.
    or you can keep the 4500 (vss) as layer-2 with no IP and no svi.
    it that more clear now?
    Reza

  • Cisco 4507R-E secondary SUP card is in disable state

    Hi All,
    I have one cisco 4507R-E switch with SUP 6-E. When I power UP switch. switch is boot with primary sup. Secondary module shown as "Disabled".
    How can i enable secondary module?

    Hi,
    Have a look at this doc on how to make the sups redundant
    You need to have the same exact IOS and license in both sups.
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/15-1-2/XE_340/configuration/guide/config/RPR.html#wp1125437
    HTH

  • Problem with Cisco 4507R

    Dear Experts,
    My switch running is normal but suddenly it has problem with red light(Output fail) as attached file.
    I also try reboot but seem to switch can not
    There is output while switch reboot:
    * Welcome to Rom Monitor for WS-X45-SUP6-E System.      *
    * Copyright (c) 2003-2009 by Cisco Systems, Inc.         *
    * All rights reserved.                                   *
    Flash die # 0: Intel 33554432Bytes
    Flash die # 1: Intel 33554432Bytes
    Flash die # 2: Intel 33554432Bytes
    Flash die # 3: Intel 33554432Bytes
    Determining FTL format status of volume.
    Volume is FTL formatted.
    Checking the partition table and boot sector...
    Checking FAT, Files and Directories...
    Reclaiming unused space...
    Updating FAT...
    Rom Monitor Program Version 12.2(44r)SG5
    CPU Rev: 2.1, Board Rev: 6, Board Type: 10, CPLD Jawa Rev: 18
    Chassis: WS-C4507R-E
    Front Panel Phy is Bcm5482s
    Got Mac Address: 00:25:84:1e:33:bc
    MAC Address  : 00-25-84-1e-33-bc
    Ip Address   : Not set.
    Netmask      : Not set.
    Gateway      : Not set.
    TftpServer   : Not set.
    ***** The system will autoboot in 5 seconds *****
    Type control-C to prevent autobooting.
    ******** The system will autoboot now ********
    config-register = 0x2101
    Autobooting using the first file from bootflash.....
    Rommon reg: 0x00004380
    Reset2Reg: 0x00000FFF
    Darkside controller 0x0B394EBC..0x0B3A326E original size:0x00012092#
    Tatooine controller 0x0B3A326F..0x0B40C25B original size:0x00094F89##
    Forerunner controller 0x0B40C25C..0x0B4D1EA8 original size:0x001D0F9C
    diagsk5 version 3.2_a
    prod: WS-X45-SUP6-E part: 73-10597-12 serial: JAE14190WMV
    Power-on-self-test for Module 3: WS-X45-SUP6-E
    Test Status: (. = Pass, F = Fail, U = Untested)
    CPU Subsystem Tests ...
    seeprom: Pass
    Traffic: L3 Looopback ...
    Test Results: Pass
    Traffic: L2 Loopback ...
    Test Results: Pass
    Switching Subsystem Memory ...
    Packet Memory Test Results: Pass
    Module 3 Passed
    Exiting to ios...
    Rommon reg: 0x00000380
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(50)SG3, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Tue 07-Jul-09 20:28 by prod_rel_team
    Image text-base: 0x10000000, data-base: 0x1222AE9C
    Any help are appreciated
    Thanks & Regards,

    Hi,
    See this:
    Table A-8     1400 W AC-Input Power Supply LEDs
    LED
    Meaning
    INPUT OK
    •Green—Source AC voltage is OK. (Input voltage is 85 VAC or greater.)
    •Off—Source AC voltage falls below 70 VAC, is not present, or the power supply is turned off.
    FAN OK
    •Green—Power supply fan is operating properly.
    •Off—Power supply fan failure is detected.
    OUTPUT FAIL
    •Red—Problem with one or more of the DC-output voltages of the power supply is detected.
    •Off—DC-output voltage with acceptable margins.
    Note For proper operation of the OUTPUT FAIL LED, systems with single power supplies must be configured with a minimum of one fan tray assembly and one supervisor engine. Systems with dual power supplies must have a minimum configuration of one fan tray assembly, one supervisor engine, and one additional module. Failure to meet these minimum configuration requirements can cause a false power supply output fail signal.
    http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/catalyst4500e/installation/guide/0aspecs.html#wp1047656
    Hope it helps.

  • Remote Access VPN on Cisco ASA Problem

    Hi, i configured Remote access VPN on Cisco ASA 8.x as per below configuration.
    Problem is that my internet has stopped working, and default route is just showing stars.
    i can ping internal server 10.110.10.150 fine , which i allowed on VPN ACL, but my other traffic not going to regular internet on my laptop,
    what additional required to force my internet to go to regular internet instead of getting encrypted?
    Also attaching output of route print at the point when VPN is connected.
    ip local pool RA_VPN_POOL 10.1.200.100-10.1.200.150 mask 255.255.255.0
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto dynamic-map RA_VPN 65535 set transform-set ESP-AES-128-SHA
    crypto dynamic-map RA_VPN 65535 set security-association lifetime seconds 28800
    crypto dynamic-map RA_VPN 65535 set security-association lifetime kilobytes 4608000
    crypto map VPN_MAP 65535 ipsec-isakmp dynamic RA_VPN
    crypto map VPN_MAP interface outside
    isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    tunnel-group ITT_RA type remote-access
    tunnel-group ITT_RA general-attributes
    address-pool RA_VPN_POOL
    default-group-policy RA_VPN_GP
    tunnel-group ITT_RA ipsec-attributes
    pre-shared-key <group key>
    group-policy RA_VPN_GP internal
    group-policy RA_VPN_GP attributes
    dns-server value 10.0.0.1 10.0.0.2
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Split_Tunnel_List
    default-domain value mydomain.com
    address-pools value RA_VPN_POOL
    access-list Split_Tunnel_List extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
    access-list nonattest extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
    nat (inside) 0 access-list nonattest
    IPv4 Route Table
    ===========================================================================
    Active Routes:
    Network Destination        Netmask          Gateway       Interface  Metric
              0.0.0.0          0.0.0.0      10.111.36.1      10.111.36.9          276
              0.0.0.0          0.0.0.0         On-link      10.1.200.100            20
           10.1.200.0    255.255.255.0         On-link      10.1.200.100    276
         10.1.200.100  255.255.255.255         On-link      10.1.200.100    276
         10.1.200.255  255.255.255.255         On-link      10.1.200.100    276
        10.110.10.150  255.255.255.255       10.1.200.1     10.1.200.100    100
          10.111.36.0    255.255.255.0         On-link       10.111.36.9    276

    Hi, i configured Remote access VPN on Cisco ASA 8.x as per below configuration.
    Problem is that my internet has stopped working, and default route is just showing stars.
    i can ping internal server 10.110.10.150 fine , which i allowed on VPN ACL, but my other traffic not going to regular internet on my laptop,
    what additional required to force my internet to go to regular internet instead of getting encrypted?
    Also attaching output of route print at the point when VPN is connected.
    ip local pool RA_VPN_POOL 10.1.200.100-10.1.200.150 mask 255.255.255.0
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto dynamic-map RA_VPN 65535 set transform-set ESP-AES-128-SHA
    crypto dynamic-map RA_VPN 65535 set security-association lifetime seconds 28800
    crypto dynamic-map RA_VPN 65535 set security-association lifetime kilobytes 4608000
    crypto map VPN_MAP 65535 ipsec-isakmp dynamic RA_VPN
    crypto map VPN_MAP interface outside
    isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    tunnel-group ITT_RA type remote-access
    tunnel-group ITT_RA general-attributes
    address-pool RA_VPN_POOL
    default-group-policy RA_VPN_GP
    tunnel-group ITT_RA ipsec-attributes
    pre-shared-key <group key>
    group-policy RA_VPN_GP internal
    group-policy RA_VPN_GP attributes
    dns-server value 10.0.0.1 10.0.0.2
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Split_Tunnel_List
    default-domain value mydomain.com
    address-pools value RA_VPN_POOL
    access-list Split_Tunnel_List extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
    access-list nonattest extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
    nat (inside) 0 access-list nonattest
    IPv4 Route Table
    ===========================================================================
    Active Routes:
    Network Destination        Netmask          Gateway       Interface  Metric
              0.0.0.0          0.0.0.0      10.111.36.1      10.111.36.9          276
              0.0.0.0          0.0.0.0         On-link      10.1.200.100            20
           10.1.200.0    255.255.255.0         On-link      10.1.200.100    276
         10.1.200.100  255.255.255.255         On-link      10.1.200.100    276
         10.1.200.255  255.255.255.255         On-link      10.1.200.100    276
        10.110.10.150  255.255.255.255       10.1.200.1     10.1.200.100    100
          10.111.36.0    255.255.255.0         On-link       10.111.36.9    276

  • Cisco 3905 problem / remote site

    Hi all!
    Information:
    I have CUCM 8.6.2.20000-2 and many Cisco IP Phone 3905 (SIP). Some of them deployed in central office and some in remote sites.
    Phone information:
    Boot Version: 3905.0-0-0-01-01
    DSP Version: 12.0.0.8
    Application: 3905.9-2-2-0
    Symptoms:
    In remote sites only!
    The phone is registered and working fine. However, after few hours idle state I lift the handset, dial any number and nothing happens. Drop the call and try again 2-3 times. After that either call passed or get permanent busy tone (need to reboot the phone to work again).
    The phone is marked as registered on CUCM and I hear dial tone when lifted the handset.
    I cannot collect debug messages from phones, because as soon as I login via telnet it going work fine.
    There is no such problem in central office.
    Phones print following messages in terminal all the time:
    17:07:10:302 x [CENTRAL] CDP/LLDP-MED CB function is called
    17:07:26:491   [sip]  03:58:24.490    pjsua_acc.c  SIP outbound status for acc 0 is not active
    17:07:26:495   [sip]  03:58:24.494    pjsua_acc.c  "п°п╦я┘п╟п╦п╩ п я┐пЇя▄п╪п╦пҐ"<sip:[email protected]:5060>: registration success, status=200 (OK              ), will re-register in 120 seconds
    17:07:26:502   [sip]  03:58:24.500         pjcu.c  pjcu_on_reg_state2(), Account["п°п╦я┘п╟п╦п╩ п я┐пЇя▄п╪п╦пҐ"<sip:[email protected]:5060>] : OK,               status=200
    17:07:26:506 x [pcu] pcuRcvHandler(CALL), SRV_EV, eid=0, cid=65535,
    17:07:26:510 x [pcu] [pcux_insrv_cb():7071] CUCM_DateTime:Mon, 27 May 2013 11:07:26 GMT
    17:07:26:511 x [pcu] Sync time from server: Mon, 27 May 2013 11:07:26 GMT
    17:07:26:515 x [pcu] [set_svr_type][1599] Bfe active_server_idx=0, serverType=0
    17:07:26:515 x [pcu] [set_svr_type][1602] Aft  serverType=0, Server Number=2
    17:07:26:531   [ipps] ----- PCU: CC_SRV, pid=0, eid=0, cid=65535 -----
    17:07:26:532   [ipps] In func: remoteNtyEvtProcess(), lib = 0, cid = 65535, ntyEv = 0
    17:07:26:533 f [ipps] In func: remoteNtyEvtProcess(), recv inservice nty, svrType = 0, cause = 0
    17:07:26:534 f [MMI] <RCV>: In func: ui_nty(), lid = 0, cid = 65535, ntyEv = 0
    17:07:26:535 x [CENTRAL] IPPS CB function(RegStatus) is called (1) with Line (0)
    17:07:26:536 f [ipps] In func: mlcu_isKpmlEnabled(), KPML value = 3, blRet = 1
    17:07:26:537 x [CENTRAL] Enter FSM: State(STANDBY) | Event(REGISTER_OK) | Cause(0)
    17:07:26:540 x [CENTRAL] Unexpected event REGISTER_OK (cause=0) at STANDBY state
    17:07:26:541 x [CENTRAL] Waiting event in STANDBY
    17:07:58:990 x [CENTRAL] CDP/LLDP-MED CB function is called
    17:08:39:022   [sip]  03:59:37.021         pjcu.c  pjcuRcvHandler(KA), KA_REQUEST, eid=-1, p1=192.168.70.1:5060
    17:08:39:040   [sip]  03:59:37.036         pjcu.c  pjcu_rpt_ka_status(), target(192.168.70.1:5060): status=1, id=27
    17:08:39:044 x [pcu] pcuRcvHandler(KA), KA_RESPONSE, eid=0, addr=192.168.70.1:5060, status=1
    17:08:39:050 x [pcu] [pcu_polling_sipserver_thread():1478] mark!
    17:08:54:130 x [CENTRAL] CDP/LLDP-MED CB function is called
    Thanks for your help.

    There are 2 versions of firmware on cisco.com. cmterm-3905.9-2-1-0 is the default firmware going with CUCM 8.6.2.20000-2 for 3905 phones and cmterm-3905.9-2-2-0 I've installed recently. Both versions of firmware with same problems.
           Some new information. I get traffic dump with wireshark.
    INVITE sip:[email protected]:5060;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 192.168.70.86:3457;rport;branch=z9hG4bKPjdp3HjFLs7Dy03RL9ce.16qung.tOq5O3
    Max-Forwards: 70
    From: "............ .............." ;tag=5a25b465-747b-4c31-a020-1a9636827427
    To: sip:[email protected]
    Contact: ;+sip.instance="";+u.sip!devicename.ccm.cisco.com="SEP10BD18DD3F59";+u.sip!model.ccm.cisco.com="592"
    Call-ID: e9edcc43-6a9b-42b8-8efc-99f702b313d1
    CSeq: 28324 INVITE
    Allow: PRACK, INVITE, ACK, BYE, CANCEL, UPDATE, SUBSCRIBE, NOTIFY, REFER, MESSAGE, OPTIONS
    User-Agent: Cisco-CP3905/9.2.1
    Supported: replaces,join,sdp-anat,norefersub,extended-refer,X-cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-cisco-monrec,X-cisco-config,X-cisco-sis-4.0.0,X-cisco-xsi-7.0.1
    Expires: 900
    Accept: application/sdp
    Allow-Events: kpml,dialog
    Remote-Party-ID: "............ ..............";privacy=off
    Content-Type: application/sdp
    Content-Length:   294
    As you can see phone trying to invite [email protected]:5060, BUT I dial 7103 DN from 7102. So where are other numbers? Bug?

  • 10.4.8 and Cisco/VPN problem solved

    Hi,
    This and related issues have arisen in threads on the past month, regarding the Cisco VPN v 4.9005 (and perhaps other VPN software) not working the same after the 10.4.8 upgrade. The problems relate to either not making a VPN connection, or data transfer after the successful connection is made, once the upgrade happened.
    The workaround was to run the Network Setup Assistant every time to do the connection properly before launching the VPN. But this is a pain.
    The eventual solution was simple, although effecting it was not straightforward. It was necessary to do a clean install of the VPN client. This is something that I could not accomplish manually, despite suggestions from the discussion group as to which files to remove, because it was difficult to find all the files that the install put it. But, at least on my machines, it could be done by command line in Terminal - cd to /usr/local/bin, ls vpn_uninstall to see if it is there, and if so, sudo ./vpn_uninstall.
    I don't know if other machines can do this or if this was part of our local IT install, but IT WORKED. I AM FREE!
    Wayne

    that's odd....
    I'm running cisco client 4.6.04 on OS X 10.4.8 and VNC without any problems...
    the only difference is my radius server is an NT box, but I can AFP and VNC to my Mac on that network.

  • New 2.4 Macbook and Cisco VPN problems?

    Is anyone else using the new MacBook Pro's with Cisco VPN? I cannot get the software to work, I get an error 51 "unable to connect to VPN subsystem" at every launch. I've ininstalled and reinstalled the cisco software, I'm using the latest VPN 4.9. I've got a 2.3 macbook pro sitting right next to it, and it runs the cisco software fine. Something with the Santa Rosa set? Any help would be greatly appreciated. I have no other network issues. All the software is up to date, system, cisco, etc. Thanks...

    Fixed my own problem, appears it's Parallels related, after I reinstalled the new parallels 3.0, cisco started working fine. Whew....;-) Hope this helps others.

  • AD Machine Authentication with Cisco ISE problem

    Hi Experts,
    I am new with ISE, I have configured ISE & Domain computers for PEAP authentication. initially machine gets authenticated and then starts going MAB.
    Authentication policy:
    Allowed protocol = PEAP & TLS
    Authorization Policy:
    Condition for computer to be checked in external identity store (AD) = Permit access
    Condition for users to be checked in external identity store (AD) plus WasMachineAuthenticated = permit access
    All of the above policies do match and download the ACL from ISE but computer starts to mab authentication again...
    Switchport configuration:
    ===============================================
    ip access-list extended ACL-DEFAULT
    remark Allow DHCP
    permit udp any eq bootpc any eq bootps
    remark Allow DNS
    permit udp any any eq domain
    permit ip any host (AD)
    permit icmp any any
    permit ip any host (ISE-1)
    permit ip any host  (ISE-2)
    permit udp any host (CUCM-1) eq tftp
    permit udp any host (CUCM-2)eq tftp
    deny ip any any
    ===============================================
    switchport config
    ===============================================
    Switchport Access vlan 10
    switchport mode access
    switchport voice vlan 20
    ip access-group ACL-DEFAULT in
    authentication open
    authentication event fail action next-method
    authentication event server dead action authorize vlan 1
    authentication event server alive action reinitialize
    authentication host-mode multi-domain
    authentication order dot1x mab
    authentication priority dot1x mab
    authentication port-control auto
    authentication periodic
    authentication timer reauthenticate server
    authentication timer inactivity 180
    authentication violation restrict
    mab
    dot1x pae authenticator
    dot1x timeout tx-period 100
    ====================================================
    One more problem about the "authentication open" and default ACL. Once the authentication succeeds and per user is ACL pushed though ISE to the switch. The default ACL still blocks communication on this switchprort.
    Your help will highly appreciated.
    Regards,

    You need to watch the switch during an authentication, see if the machine is passing authentication and the user may be failing authentication causing the switch to fail to mab.  If your switch configuration is on auth failure continue to next method, then this makes sense.  The question is why is the user failing auth but the machine is passing, could be something in the policy.  Make sure your AD setup has machine authentciation checked or it may not tie the machine and user auth together and the user may be failing because ISE can't make that relationship so the machinewasauth=true is not beeing matched.  Easy way to check is remove that rule from your policy and see if the same thing happens.
    I've also seen this happen when clients want to use EAP-TLS on the wired, machines passes auth, then the user logs into a machine for the first time.  The user auth kicks off before the user gets a cert and fails auth with a null certificate, since this is a auth failure the switchport kicks over to MAB.
    I don't think wasmachineauth=true is that great, I prefer to use EAP-FASTv2 using Cisco Anyconnect NAM with eap-chaining.  This is great because you can do two part authentication.  EAP-FAST outer with EAP-TLS inner for the machine auth, and MSCHAPv2 for the inner of the user auth. You get your EAP-TLS auth for the machine and don't have to worry about a user logging into a machine for the first time and switching to MAB because the user doesn't have a cert yet.  I also do my rule to say if machine pass and user fail, then workstaion policy, if machine and user pass then corp policy.

  • Cisco 1310 problem

    First, i want to apologize for my English.
    I have a wireless network, which connects areas isolated by the sea.
    One of the repeaters have connection problems.
    There is a picture that illustrates my problem.
    The repeater in red, was installed recently. Because of the distances are added to each output TNC an amplifier of 1 watt.
    The problem arises when the bridge that connects to the repeater, it begins to traffic on the network.
    The repeater is disconnected, leaving the bridge and repeater offline.
    We believe that the problem is caused by the fact that this link is at 12 meters above sea level. And we think that we could solve that problem by adding two amplifiers to the Master AP.
    Any suggestion.

    You did not include the config files for the 1310's, did you set the distsnce prameter for the radio on the root bridge. for longer distances the AP needs to adjust the time out values.
    http://cisco.com/en/US/docs/wireless/access_point/12.3_8_JA/command/reference/cr38main.html#wp2481270
    Hope this helps.
    Bill

  • Cisco 3550 Problem

    I have a number of C3550 switches in the field and one of them seems to have a problem showing Interface statistics on some fast Ethernet ports.
    Most ports are running at 100Meg Full-duplex, but some fail to show any "5 minute rate" stats when I do a show interface command. You can only determine the data rate throughput by doing succesive show int commands at set time intervals and counting the difeerence in the total packets received/transmitted sections.
    Has anyone seen this elsewhere? Is this a known problem as I can't see any reference to this as a problem on TAC
    The IOS version is 12.1(13)EA1a

    There was a known issue for interfaces with low rate of pps(<40 pps) because of the way the counter is implemented. Look at the following bug which is in a Closed state(not resolved)
    http://www.cisco.com/cgi-bin/bugtool/onebug.pl?bugid=CSCdz06305
    Change the load-interval to 30 seconds and see if this makes any difference.

  • Cisco IOS problem

    I have this error when I start my router
    System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
    Copyright (c) 2003 by cisco Systems, Inc.
    Bad RAM at location 0x00000000: wrote 0x00000000, read 0x00000400
    Which is the problem? How can I fix it?

    RAM is creating problem or you can say that not compatable just change your RAM ( If 2 RAMS are placed in Router then unplugged ram 1 by 1 like unplug 1st RAM and check then place 1st RAM back and unplug 2nd RAM and then check
    i m sure your problem will solve
    Hope this will help you
    if yes then rate this article

  • Cisco E900 problem

    Hi I bought a Cisco E900 wireless router in the last week. Its blocking certain websites .Its even blocking where a user has to sign in yahoo answers page or to sign in even the yahoo mail.
    Please help me Its urgent

     I have a broadband connection with ADSL modem.  The modem and router are connected as ofcourse seen from the documentation correctly. I am getting excellent signal strength in my laptop also
     I can access many other sites without any problem.Its just with some sites that are causing problem like yahoo sign in pages(but the yahoo page is accessible,from that when I click sign in or mail link it doesn't load). Also with UHRS web entry login I am experiencing issue, this site also loads but when I use its sign in button nothing happens just that site stays without any action.
    Do u want me to share the snapshot , because only it says is the usual error display with browser ie
    the web page  is not available. 
    Please help to solve this issue as soon as possible

  • Cisco 7204VXR problem

    I am experiencing a problem with a Cisco Router 7204VXR with the fastEthernet interface. The board is model PA-2FE-TX (FE2/0 and FE2/1): the FE2/1 seems to work correctly, while I have problems with the FE2/0. After putting it up and as soon as a data traffic greater than a ping passes through it, the interface becomes "frozen", still remaining up. Sometimes this fact causes problems also to the other interface (FE2/1).
    I also replaced the board, but the problem remains. I observed the presence of a lot of collisions (in half-duplex mode), while in full duplex-mode neither a ping works.
    Thanks in advance for your help

    Hi, I suppose that u want to see the counters on the fa 2/0 while is working, but unfortunatelly i' ve setted it down few days ago couse it was causing some prob to the other interface fa 2/1 (on the same slot) and i had to reboot the router then. It was losing some packets!
    Anyway the interface 2/0 was giving me many collision and deferred packets while it was still active!
    If u want i can tell u the others board mounted on the router. Or something of other u want to know!

  • CISCO - Unsolved problems

    I am very disappointed with CISCO, do not know say whether the company entered the Brazilian market to compete with expensive products and low quality. Lately acquired a 5 CISCO products for personal use and for my clients, one of them had no solution came with factory defect and was conducted with the RMA costs the customer time and money. The other products offered performance worse than poor quality products offered in my city. Summarizing like buying quality products that offer high performance and stability, however the cisco trivialized their products and lost a lot of quality in recent times, several products with bugs, signal strength well below international standards specified by 802.11 mainly. Do not go back nor recommend buying CISCO products, they are expensive and implement problems in networks that administer.
    It is very necessary that the company provides on its site firmwares to correct defects and not to implement even more defects!

    Cisco products perform pretty well, based on my experience. What problems were you encountering, by the way? and on which products?

Maybe you are looking for

  • How to solve error (-23) when updating my iPhone to iOS5?

    I was about to download the iOS5 on my iPhone but it kept on saying that there was a problem when downloading and "An unknown error occured (-23)". Can anyone help me? My iTunes and Mac's software are up to date.

  • Export and import of data not table and data ????

    hii brothers and sister plz i have a a quetion about Export and import of data in oracle forms i have created 02 boutons one for export his trigger like this : eclare alrt number; v_directory varchar2(200) := 'c:\backup'; --- that if the C Drive not

  • ISync won't launch

    What makes an app not launch? It flickers but then it never becomes active in the finder. I've tried deleting preferences for the app (this happens all the time with my Preview and once I delete the preferences its works again). I tried copying iSync

  • How to check summarized item status

    I have a control block having 12 testitems as summarized of 12 months(of data block) My form validation is if total less than 100 then just alert the user Iwant to alert the user only for the respective month when the value is changed in the total. I

  • ITS Mobile Date Field Problemn

    In ITS Mobile I developed a screen which contains a date field. I click question button to select a date, it opens a new screen which includes a calendar. But I can not select a date because no clickable days in new date selection screen. What can i