Cisco 5 port and 8 port gigabit unmanaged switches
I am looking for 5 port and 8 port gigabit unmanaged switches in Cisco. Please provide the BoM for the same. As per my understanding the following switches can suffice the requirement (SG100D-05 and SG100D-080) however I am not sure about the DC power, whether they can be used in normal AC environments.
The SG100D-05 and SG100D-08 are too small and their power requirements are too low to justify building an AC power supply into them like the larger SGx00 switches have, so they are wired to accept DC power and use an external power adapter (included) for connection to an AC environment.
There are really no optional components to these devices, so the BOM would be as follows:
5-port SG100D swich: SG100D-05
8-port SG100D swich: SG100D-08
Similar Messages
-
SR2016T-EU 16 PORT GIGABIT UNMANAGED SWITCH
I bought the above mentioned model few days before for my small business of internet cafe with 16 computers by accepting the advice given by the
person who sold me this apparatus inorder to have equal and good connection for all the computers.i just want to make sure if this apparatus is the right one for the purpose i want to use for.for your information i am using a wired network.would you please give me your advice if i a on the right direction to suceed in my business.thank youNever mind.
While at my desktop machine, I absentmindedly configured my network preferences for PPPOE, instead of leaving it to the router.
Once I adjusted my desktop machine for DHCP, all was well.... -
CISCO SG200-50 Port Gigabit Smart Switch (VTP Support)
Does CISCO SG200-50 Port Gigabit Smart Switch provide support for VTP or Not. If not how we can make it a VTP client and how it will forward its VLAN information to VTP Server in VTP Domain in which it is connected.
ThanksHi Jay,
I am not very sure if this is the correct location to find the MTU, but you may check the following link:-
http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbss/sf20x_sg20x/administration_guide/78-21139.pdf
Administration > Discovery - LLDP > LLDP Local Information
LLDP Port Status Table
LLDP Local Information Details
802.3 Details
Let me know if this helps.
Aniket -
SG300-28 28-Port Gigabit Managed Switch
I've forgotten username & password of SG300-28 28-Port Gigabit Managed Switch. Is there any to recover them? but I don't want to lose configurations.
Hi Anton,
You can access boot menu and choose password recovery but this option is only accessible via serial console and after you see Cisco logo hit ESC button once.
Once you choose password recovery current password will be ignored during this current session only so the first thing you need to do is to change and save new password. You can use CLI for this:
switch(config)#username cisco password cisco
switch(config)#exit
switch#wr
and you should be ready to go :-)
Aleksandra -
SG 300-28 28-Port Gigabit Managed Switch -Lan connectivity issues
Hello,
Our office lan running on 2 * SG 300-28 28-Port Gigabit Managed Switch.
PID VID:SRW2024-K9 V01
Firmware Version (Active Image):1.0.0.27
The users are seeing there connection to fileservers(mapped network drives) slowing down over the period.
We have to re-boot the offending switch to get the normal traffic back.
I have raised a ticket with cisco small business people and they said to upgrade the firmware to latest version.
But I am wondering why I need to upgrade this switch as the other switch which also brought at the same time with the same spec have no such issues.
Even if I decided to upgrade the firmware, they have recommended that I need to reset the switch to factory settings and try to put the previous configuration manually which is a worry for me.
I have logged on to the web console and I have found out, I can use TFTP or HTTP to backup the config,how do I use those services and what parameters i need to pass those to work, does using that functionality can rollback the switch to previous running configuration?
PS: Both the switch have connected together using a FC trunk with link aggregation eanbled.So how do I get all those settings back if I upgrade/rollback?
I just have to come up with some solution as it is affecting the business, so any help would be much appreciated.
Please see the attachment and let me know if any other info needed?
Thanks in advance,
Regards
SujiHi,
Please see the difference between the connected switches configuration.
Maybe the vlan 10 and 30 has been created wrongly.
Please see the config for both the switches and give me some advice/suggestions.
I really appreciate that.
Bad Switch Config
/* This is the config for the bad switch */
interface port-channel 1
flowcontrol auto
exit
interface port-channel 2
description netAppFiler1
exit
interface port-channel 3
description Switch
flowcontrol auto
exit
port jumbo-frame
vlan database
vlan 10,30
exit
interface ethernet g12
switchport trunk native vlan 10
exit
interface ethernet g24
switchport trunk native vlan 30
exit
interface vlan 10
name Private
exit
interface vlan 30
name "Private 2"
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
port-channel load-balance layer-2-3
interface range ethernet g(25-26)
channel-group 2 mode on
exit
interface range ethernet g(27-28)
channel-group 3 mode on
exit
interface range ethernet g(27-28)
lacp timeout short
exit
interface range ethernet g(1-26)
lacp port-priority 2
exit
ip dhcp relay address 192.168.0.1
ip dhcp relay enable
ip dhcp information option
interface vlan 1
ip dhcp relay enable
exit
bonjour service enable csco-sb
bonjour service enable http
bonjour service enable https
bonjour service enable ssh
bonjour service enable telnet
hostname switchbad
line console
exec-timeout 0
exit
line ssh
exec-timeout 0
exit
line telnet
exec-timeout 0
exit
username admin password xxxxxxxxxxxxxxxxxxxxxxxxxx level 15 encrypted
no snmp-server enable
snmp-server location "Server Rack"
ip http exec-timeout 0
ip https exec-timeout 0
clock timezone 1
clock dhcp timezone
ip name-server 192.168.0.1 192.168.0.9
snmp-server set rlAutomaticClockSetFromPCEnabled rlAutomaticClockSetFromPCEnabled true
Good Switch Config
/* Good switch run config *
interface port-channel 1
description Switch
flowcontrol auto
exit
port jumbo-frame
lacp system-priority 2
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
port-channel load-balance layer-2-3
interface range ethernet g(27-28)
channel-group 1 mode on
exit
interface range ethernet g(27-28)
lacp timeout short
exit
interface range ethernet g(1-26)
lacp port-priority 2
exit
interface port-channel 1
switchport protected-port
exit
ip dhcp relay address 192.168.0.1
ip dhcp relay enable
ip dhcp information option
bonjour service enable csco-sb
bonjour service enable http
bonjour service enable https
bonjour service enable ssh
bonjour service enable telnet
hostname switchbaebf1
line console
exec-timeout 0
exit
line ssh
exec-timeout 0
exit
line telnet
exec-timeout 0
exit
aaa authentication enable Console local
aaa authentication enable SSH local
aaa authentication enable Telnet local
aaa authentication login Console local
aaa authentication login SSH local
aaa authentication login Telnet local
line telnet
login authentication Telnet
enable authentication Telnet
password xxxxxxxxxxxxxxxxx encrypted
exit
line ssh
login authentication SSH
enable authentication SSH
password xxxxxxxxxxxxxxx encrypted
exit
line console
login authentication Console
enable authentication Console
password xxxxxxxxxxxxxx encrypted
exit
username admin password xxxxxxxxxxxxxx level xy encrypted
ip ssh server
snmp-server location "Comms rack"
ip http exec-timeout 0
ip https server
ip https exec-timeout 0
clock summer-time recurring eu
sntp unicast client enable
sntp unicast client poll
sntp broadcast client enable
sntp server xx.yyy.zz.70 poll
sntp server zz.yyy.xx.201 poll
sntp server zz.yy.xxx.2 poll
sntp server xzz.xxx.xy.149 poll
clock dhcp timezone
ip name-server 192.168.0.1 192.168.0.9
ip telnet server
snmp-server set rlAutomaticClockSetFromPCEnabled rlAutomaticClockSetFromPCEnabled true
Regards
Smith -
SG 300-52 52-Port Gigabit Managed Switch
Hi Gentlemen,
We have recently purchased SG 300-52Port Cisco Switch to support our Network but they constantly having some bizarre issues or I assume bugs, i.e. we cannot Telnet nor SSH to the switch now, whereas we were able to SSH before, we have set them up for Remote Log Services to get some syslogs and reports but no report have been generated nor logs,
I have done some testing through Wireshark and there are absolutely no reports / logs.
We have some real issues with this switch and it’s hard to believe that this is a Cisco Product,
SG 300-52 Port Gigabit Managed Switch
Firmware Version (Active Image ) : 1.1.1.8
Firmware Version (Non-active ) : 1.1.0.73
Boot Version : 1.0.0.4
It would be appreciated if someone could shed some light so that we could fix these issues.
Thanks.Yes, i am able to log into Web GUI,
I have had some serious issues before with set up/add different VLANs but we somehow make it work even though i am not optimistic...
Other problem that is now pending is setup Remote Log Services to get some syslogs.. it doesn’t generate anything no logs no reports ...
I am going to backup it up / reset /update the firmware again and see how it works.
Let me know if you have any suggestion.
Thanks. -
Link srw2048 and linksys 8 port gigabit smart switch linking together
Hi all,
I would like to link my srw2048 in the my celler to the linksys 8port switch i have in the living room so my son can have lan parties. how would i configure this and will i need to make a crossover cable?
Thanks in advance for any adviceI don't see the need of configuring your SRW2048 switch for you to be able to connect your 8 port gigabit switch. Since these switches were both smart switch you can use either crossover or straight through cable for them to communicate with each other.
-
CLI support for Cisco SG100D-05 5-Port Gigabit Desktop Switch
I would like to know if the SG100D series of switches support the CLI? If not what are the series of switches supported by the CLI.
I am looking for an application where I need to tell which device is connected to which port on a switch. Hence I am looking at this option where I can run a script and use CLI to output the MAC id of devices connected on each port.
Thanks!Hi Yiu Kay Lee,
Thank you for sending me this document. It was very helpful. But I cannot understand one thing about it. Is it possible to extract the results from the CLI by passing a command via a script e.g. Python and get the results of it into Python?
For e.g.
************Python script ******************
>>print("send command to 200 series Cisco switch")
>> results = show mac-addr-table
>> print results
Please let me know if such interfacing with the CLI is possible or not?
Thanks -
SG200-26 26-Port Gigabit Smart Switch - MTU settings
SG200-26 26-Port, firmware 1.3.7.18
I have MTU mismatch on the network and the last device that can be responsible for the mismatch is my Cisco SG200-26. I was looking long and hard for where I can at least check what is the value of MTU on the switch but I can't find it. Ideally I would like to know not only where to check it but also where to change it. Can you please help?
Many thanks,
JayHi Jay,
I am not very sure if this is the correct location to find the MTU, but you may check the following link:-
http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbss/sf20x_sg20x/administration_guide/78-21139.pdf
Administration > Discovery - LLDP > LLDP Local Information
LLDP Port Status Table
LLDP Local Information Details
802.3 Details
Let me know if this helps.
Aniket -
Cisco SG300-52 52-Port Gigabit Managed Switch losing VLAN-Port Membership
Hello
We have some cisco switches in use and we're facing some problems everytime the switch loses Power.
After a reboot the port/vlan membership is lost, so are other settings recently made (like SSH access allowed, etc.).
The settings made up a year ago like the IPs, password, etc. remain untouched.
Upgrading the Firmware, Saving the Configs, etc. didn't solve the problem.
Is this a known issue? Anyone facing the same problem?
Bye and thanks for the help.
ViktorVlan Name Tagged Ports UnTagged Ports Created by
1 1 gi51-52,Po1-8 D
10 10 gi51-52 S
20 20 gi51-52 S
30 30 gi51-52 S
40 40 gi51-52 gi1-9,gi14-34, S
gi38-41,gi49-50
50 50 gi51-52 S
100 100 gi51-52 S
190 SecurityNetwork gi51-52 gi11-13,gi35-37 S
200 200 gi51-52 S
210 Wireless gi51-52 gi10 S
300 ServerSubnetOne gi51-52 gi42-48 S
config-file-header
as4
v1.4.0.88 / R800_NIK_1_4_194_194
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
no cdp run
no spanning-tree
port jumbo-frame
vlan database
vlan 10,20,30,40,50,100,190,200,210,300
exit
voice vlan state disabled
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
no lldp run
hostname as4
no passwords complexity enable
username cisco password encrypted xxxxx
ip ssh server
snmp-server location Eingang
snmp-server contact [email protected]
clock timezone " " +1
clock source sntp
sntp unicast client enable
sntp unicast client poll
sntp server 157.161.57.2 poll
ip name-server 192.168.200.1
interface vlan 190
name SecurityNetwork
interface vlan 200
ip address 192.168.200.34 255.255.255.0
interface vlan 210
name Wireless
interface vlan 300
name ServerSubnetOne
interface gigabitethernet1
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet2
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet3
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet4
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet5
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet6
spanning-tree disable
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet7
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet8
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet9
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet10
switchport mode access
switchport access vlan 210
lldp med disable
interface gigabitethernet11
switchport mode access
switchport access vlan 190
lldp med disable
interface gigabitethernet12
switchport mode access
switchport access vlan 190
lldp med disable
interface gigabitethernet13
switchport mode access
switchport access vlan 190
lldp med disable
interface gigabitethernet14
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet15
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet16
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet17
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet18
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet19
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet20
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet21
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet22
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet23
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet24
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet25
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet26
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet27
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet28
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet29
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet30
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet31
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet32
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet33
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet34
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet35
switchport mode access
switchport access vlan 190
lldp med disable
interface gigabitethernet36
switchport mode access
switchport access vlan 190
lldp med disable
interface gigabitethernet37
switchport mode access
switchport access vlan 190
lldp med disable
interface gigabitethernet38
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet39
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet40
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet41
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet42
switchport mode access
switchport access vlan 300
lldp med disable
interface gigabitethernet43
switchport mode access
switchport access vlan 300
lldp med disable
interface gigabitethernet44
switchport mode access
switchport access vlan 300
lldp med disable
interface gigabitethernet45
switchport mode access
switchport access vlan 300
lldp med disable
interface gigabitethernet46
switchport mode access
switchport access vlan 300
lldp med disable
interface gigabitethernet47
switchport mode access
switchport access vlan 300
lldp med disable
interface gigabitethernet48
switchport mode access
switchport access vlan 300
lldp med disable
interface gigabitethernet49
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet50
switchport mode access
switchport access vlan 40
lldp med disable
interface gigabitethernet51
switchport trunk allowed vlan add 10,20,30,40,50,100,190,200,210,300
lldp med disable
interface gigabitethernet52
switchport trunk allowed vlan add 10,20,30,40,50,100,190,200,210,300
lldp med disable
exit -
SG 200-18 18-Port Gigabit Smart Switch VLAN Setup Help Required
Small Network in my home using Cisco SG 200-18 also have Meraki MX60 Router.
2 of my Windows 2008 Server have Dual network adapters.
Need to put the second network adapter on another subnet.
My primary network is 10.2.8.x/22 10.2.8.1 is Gateway 255.255.252.0 is the subnet
New network is 10.1.8.x/22 Gateway is 10.1.8.1 Subnet 255.255.252.0
I need both networks to be able to talk to each other.
On one server I have both network adapters configured properly
My Meraki MX60 is configured with a VLAN of 1018 MXIP 10.1.8.1 one LAN port on the Meraki MX60 we tested and made it on the new VLAN
If I plug the second network adapter from my test server into the Meraki MX60 Lan Port and it all works from my pc on 10.2.1.x I can ping 10.1.8.1 which is the Meraki MX60 and I can ping 10.1.8.23 which is the test server.
My PC (10.2.8.99) can ping 10.1.8.23 also
Now for my Question
When I plug my Test Server second network adapter into port 13, 14 15 or 16 of the SG 200 I can not:
1. from my pc (10.2.8.99) ping 10.1.8.23
2. From the Meraki (10.2.8.1) I can not ping 10.1.8.23
3. From the Test server (10.1.8.23) can not ping 10.1.8.1
How do I configure the SG200 correctly?
I created a VLAN named 1018 (See the attached screen images)
How does my config look?
What am I missing????
Thanks in advanceHi,
If I understand correctly you are trying to do inter-vlan routing, for packest to pass from one vlan/subnet to another it must be routed, than can be done by using a layer 3 switch ( the most optimal way ) or by using a router with a layer 2 witch, if you are using a router the router must have an interface in each vlan, you can also use sub-interfaces if the router you are using supports it. Another thing I noticed on your switch is that your ports are configured as trunks, this may not work well unless you know exactly what you are doing and you have a specific need. -
Sb Sg300-10mp 10 Port Gigabit Poe Switch
Good afternoon,
Really need some assistance with this switch please.
When it's switched on it keeps going into a boot cycle. It's never worked but due to reporting it outside the accepted DOA timescale we are unable to return the unit,
Please could someone advise what I need to do?
Thank you in advance,
AmandaHi Amanda,
Sure does sound like a real problem.
But the switch has a tremendous warranty and support is free for products under service contract or warranty.
If you would be so kind as to contact the good folks at the Small Business Support Center (SBSC), they will either help fix the product or allow for RMA of the unit. their contact details are on the second URL below.
A SBSC technician will ask for a Cisco Connection online (CCO) ID, if you don't have one, go to the following URL to create one. https://tools.cisco.com/RPF/register/register.do This allows the the technicians to have contact details for you and for you to manage your service requests online at Cisco if that is what you want to do..
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
regards Dave -
SRW2024P 24-Port Gigabit PoE Switch
Hello,
I am trying to use the SRW2024P Switch to setup a converged lab, with 7970, 7960g, and CCM. How do I set this switch up to setup VLANs and QoS/CoS/ToS to prioritize voice, video, and data in that order (perhaps data to use the defualt VLAN)?Hi Amanda,
Sure does sound like a real problem.
But the switch has a tremendous warranty and support is free for products under service contract or warranty.
If you would be so kind as to contact the good folks at the Small Business Support Center (SBSC), they will either help fix the product or allow for RMA of the unit. their contact details are on the second URL below.
A SBSC technician will ask for a Cisco Connection online (CCO) ID, if you don't have one, go to the following URL to create one. https://tools.cisco.com/RPF/register/register.do This allows the the technicians to have contact details for you and for you to manage your service requests online at Cisco if that is what you want to do..
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
regards Dave -
SG100-24 Unmanaged Switch Issues
I have a new SG100-24 Port Gigabyte unmanaged switch. Recently some of the ports on the switch started acting up and we lost connectivty on several ports. Called Cisco TAC and they sent me a new one, same issues on the replacement on several of the ports. After further troubleshooting with TAC, it was determined that this is a known issue with this model of switch. If a port stops communicating the official work around from the TAC was to set the NIC card of the PC to 100 MB full and then normal connectivity returned to the PC from the troubled ports on the switch.
This doesn't seem like the greatest work around solution to me, and at this time i was told Cisco has no official plan of action for a permanent fix for this model of switch, and that a replacement with a new model hasn't been approved by cisco.
Does anybody have futher insight as to whether or not there will be a fix release ( maybe firmware ? ). Or will cisco just replace this model with different model for customers experiencing this issue ?
Thanks,
Keith ArnoldThis does not sound correct .
Setting a PC port to 100MFull will cause switch port auto-negotiation to fail.
I will forward this posting to the unmanaged switch product manager for his comments.
But in the mean time, can you please be so kind as to email me at [email protected] with your Small Business Support Center Service Record(SR) number so I can check the case notes for more details.
Usually this SR number it starts with the numbers 61xxxxxxx
regards Dave -
Do unmanaged switches for ex. 3com officeconnect unmanaged 8 port switches have MAC address tables.
For ex. I have a 8 port 3com unmanaged switch connected to port 0/1 on a 3750 switch.
Does the unmanaged switch keep track of the MAC addresses that it has for its 8 ports ? or is it like a hub and repeates the signal ?
If it doesnt have a MAC address table, wouldnt it be considered a Layer 1 switch ?yes even nonmanagable switch also keep their MAC address table in order to perform the switching function...they are able to do all the normal switching function which we can able to do in our manageable switch...the only thing is you cannot configure it to make it work for your purpose...
and when ever you are talking about layer1 device then they always going to have broadcasting of packet as they are not using any addressing...so those devices are only having brodcast...
hope this will help you
rate this post if it helps
regards
Devang
Maybe you are looking for
-
How can I transfer all my information from iphone 4 to iphone 5
I tried to transfer the information but a window was open that required a password, I wrote my itunes password but it says incorrect. I need to transfers everything: apps, contacts, music. Please help me
-
updated from lion to m/lion no mikes work , i have re installed still no joy any idea before i do a clean install
-
Only 200 songs will import to my 2GB ipod nano
i have had to reset my ipod after getting what i thought was a virus. The ipod kept on skipping over songs. After reseting that problem has gone away. Now i can only get about 200 songs onto the thing. I should be getting 500? Any ideas as to why thi
-
Dear all, I have one requirement saying that whenever anyone amending the po it should trigger a mail to the higher authorities. For this one i can get althose details except conditon split up. CDPOS i can get the net value item (total value of the i
-
Image gets "stuck" in reader and I can't open new.
I have a treo 700wx running windows mobile 5.0. Downloaded Reader for pdf files. It opens the first file flawlessly. When you try to open a subsequent file, it's like the original image gets "stuck" in the viewer. I have to perform a reset to mov