Cisco 7200 HSRP Dual-Stack
Hi;
May i use HSRP for ipv4 and ipv6 at the same time on same interface ?
Our interface;
interface GigabitEthernet0/3
description Firewall
ip address 193.x.x.x 255.255.255.192
ip flow ingress
ip policy route-map network-load
load-interval 30
duplex auto
speed auto
media-type rj45
negotiation auto
standby 3 ip 193.x.x.x
standby 3 priority 130
standby 3 preempt
we want to use 2001:047c:xx::5 for standby ip.
for nodes:
2001:047c:xx::6
2001:047c:xx::7
Is it possible ?
Thanks
Hi,
What feature set i.e Enterprise Services, IP services, etc...?
sh ver | inc bin
Is that NPE-G1 or G2?
HTH
Similar Messages
-
I have a design I'm working on which will require among other things dual stack across MPLS. Configuring CE routers for dual stack seems very straight forward, however I'm having trouble finding documentation describing the BGP config for multihoming and load sharing with 2 routers and 2 service providers. I've configured this quite a few times with HSRP and BGP for IPv4 similar to this example:
http://www.cisco.com/en/US/tech/tk365/technologies_configuration_example09186a00800945bf.shtml#conf5
Am I looking at this wrong or are these scenarios just not widely published yet?
Any help is greatly appreciated!
thanks,
JoshHi Josh,
You will have to understand the MBGP address families. One of the basic rule of MBGP is that when I'm advertising a route from a specific address family, the next hop has to be from the same address family. So, you will have to make sure the next hop is from the same address family. Couple of examples for you:
1. IPv6 NLRI in IPv4
router bgp 201
bgp router-id 192.168.30.1
neighbor 150.1.1.2 remote-as 301
address-family ipv6
neighbor 150.1.1.2 activate
neighbor 150.1.1.2 route-map SETNH out
network 2192:10::/48
route-map SETNH permit 10
set ipv6 next-hop 2150:1:1::3
2. IPv4 NLRI in IPv6
router bgp 201
bgp router-id 192.168.30.1
neighbor 2150:1:1::2 remote-as 301
address-family ipv4
neighbor 2150:1:1::2 activate
neighbor 2150:1:1::2 route-map SETNH out
network 192.10.0.0
route-map SETNH permit 10
set ip next-hop 150.1.1.3
I also came across this document which should help you: http://fengnet.com/book/Cisco.IOS.Cookbook.2nd/I_0596527225_CHP_25_SECT_11.html
Regards,
Salman -
6VPE and Dual Stack Core?
Hi,
I've been following this discussion on a MPLS migration to IPv6.
https://supportforums.cisco.com/thread/2181573
I have the following customer requirements:
- Dual stack IPv4/IPv6 across the entire network including the core.
- Run 6VPE between the PE routers
Is it true to say that this is not a supported configuration? 6VPE only runs on a native IPv4 core?
Thanks
Sean6VPE is a tunneling technology to allow you to run IPv4 and IPv6 over an IPv4-only core and provide dual-stack at the customer edge. The customer is blissfully unaware that there is anything other than dual-stack - or better described as IPv4 and IPv6 capabilities - at their demarcation.
If you configure your entire core with dual-stack, there isn't really a need for 6VPE. What you will need is a solution for LDPv6 or what is sometimes referred to as MPLSv6 (http://blogs.cisco.com/tag/ldpv6/).
cheers. -
Dual stack BGP Configuration guide for enterprise CPE
Hi,
I couldn't find the config guide for BGP in a IPv4 & IPv6 dual stack environment for CPE in Cisco website. Hope someone can share the URL.
ThanksThe following URL shows how to configure Multi-protocol BGP - http://www.cisco.com/en/US/docs/ios-xml/ios/iproute_bgp/configuration/15-mt/irg-15-mt-book.html.
hth,
-jim -
Dual-Stack LNS - ppp negotiation fails if no ipv6 prefix assigned by Radius
Hello,
We have an LNS (asr1k), dual-stack CPE and Radius server.
Everything works fine if both ipv4 and ipv6 prefix is assigned to CPE by Radius
If we set Radius server not to assign v6 prefix, we expect to build up an ipv4-only session over ppp.
This is not what happens. PPP negotiation fails with the following debug lines:
IPv6 DHCP_AAA: No authorization data from SSS
Vi2.2364 PPP DISC: Non-PPP hang up
some config parts of LNS:
no ipv6 source-route
ipv6 unicast-routing
ipv6 dhcp binding track ppp
ipv6 dhcp pool IPv6_DHCP_POOL
ipv6 dhcp pool POOL_DHCP_PD
ipv6 multicast-routing
ipv6 multicast rpf use-bgp
interface Virtual-Template99
mtu 1460
ip unnumbered Loopback0
ip tcp adjust-mss 1420
no logging event link-status
ipv6 enable
no ipv6 nd prefix framed-ipv6-prefix
no ipv6 nd ra suppress
ipv6 dhcp server POOL_DHCP_PD allow-hint
peer default ip address pool adslpool_1 adslpool_2
ppp max-configure 3
ppp authentication pap AAA_AUTHEN_PPP_noc3x
ppp authorization AAA_AUTHOR_NET_noc3x
ppp accounting AAA_ACCT_NET_noc3x
ppp ipcp address required
ppp ipcp address accept
ppp ipcp no-renegotiation send-termreq
ppp link reorders
ppp timeout retry 5
ppp timeout ncp 30
ppp timeout authentication 30
end
Can anyone help?
Regards,
AntalHave opend a case with cisco. The solution for me is to put
no ipv6 dhcp ppp terminate
in to the global config.
Hope that helps anyone who has the same problem. -
[ASR1K] ISG Dual Stack configuration
Hello
Is it possible to configure l3-connected ISG dual stack on ASR1000?Hi,
According to document http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/isg/configuration/xe-3s/asr1000/isg-xe-3s-asr1000-book/isg-ipv6.html, it is possible:
Restrictions for ISG IPv6 Support
Layer 2 connected interfaces are not supported. Only Layer 3 routed in-band IPv6 sessions are supported.
Session Coexistence on ISG Interfaces
The following session combinations can exist on the same ISG interface in Cisco IOS XE Release 3.5S and later releases:
Native IPv6 and native IPv4 sessions
Regards -
Hello...
I have configured a dual stack VLAN on cisco 6500 switch and assign a ipv6 address on my LAPTOP and connected to the VLAN .but my laptop is not identifying the ipv6 address and gateway is also not pinging from the laptop. rest configuration on swich is ok . what may be the issue . can anyone suggest waht may be the issue.Dear Sunny,
thank you for your answer.
I've already tried this method. Unfortunately it didn't help, because the upgrade tool is not searching for those packages in other directories.
In the meantime I found out a possible reason of the problem. It seems the usage type of the JAVA is not correct. In configtool I saw it is DW. The list of the problematic components contains all of the XSS components and one other.
I will try the following workaround:
- Undeploy all 'wrong' components before the upgrade
- Remove the components from the stack xml
- Deploy the missing components
BR,
Veronika -
Hi,
I have a Dual Stacked DMVPN Hub site, VPN for ether IPv4 oder IPv6 is working properly, but not both at the same time.
If the IPv4 Peers connect first, then the IPv6 Peers are unable to form an IPsec security association and the other way around. Crypto ISAKMP Phase1 is build correctly.
A "show crypto ipsec sa" on the Hub shows only sa's for the kind of Peers that connected first. A "show crypto ipsec sa" on the Spoke that is unable to form an security association with the Hub shows an security association, but with no proposals and raising send error counters:
Spoke (IPv4) SA
interface: Tunnel1
Crypto map tag: My-Profile-v4-head-1, local addr 2.2.2.1
protected vrf: (none)
local ident (addr/mask/prot/port): (2.2.2.1/255.255.255.255/47/0)
remote ident (addr/mask/prot/port): (1.1.1.1/255.255.255.255/47/0)
current_peer 1.1.1.1 port 500
PERMIT, flags={origin_is_acl,ipsec_sa_request_sent}
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 23255, #recv errors 0
local crypto endpt.: 2.2.2.1, remote crypto endpt.: 1.1.1.1
plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb (none)
current outbound spi: 0x0(0)
PFS (Y/N): N, DH group: none
inbound esp sas:
inbound ah sas:
inbound pcp sas:
outbound esp sas:
outbound ah sas:
outbound pcp sas:
protected vrf: (none)
I'm running IOS Version 15.3(2)T, is there some kind of known bug and/or a workaround for this?
Interface Configuration
interface GigabitEthernet0
description ** Outside **
ip address 1.1.1.1 255.255.255.0
duplex auto
speed auto
ipv6 address 2001:1:1:1::1/64
Crypto Configuration
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 14
crypto isakmp key cisco address 0.0.0.0 no-xauth
crypto isakmp key cisco address ipv6 ::/0 no-xauth
crypto isakmp keepalive 10 periodic
crypto ipsec transform-set My-Set esp-aes 256 esp-sha512-hmac
mode tunnel
crypto ipsec profile My-Profile-v4
description ** IPsec Profile fuer IPv4 Peers **
set transform-set My-Set
set pfs group2
crypto ipsec profile My-Profile-v6
description ** IPsec Profile fuer IPv6 Peers **
set transform-set My-Set
set pfs group2
Tunnel Configuration
interface Tunnel1
description ** DMVPN Intranet IPv4 **
bandwidth 1000
ip vrf forwarding VPN
ip address 10.0.10.1 255.255.255.0
no ip redirects
ip mtu 1416
no ip next-hop-self eigrp 65351
no ip split-horizon eigrp 65351
ip pim sparse-mode
ip nhrp map multicast dynamic
ip nhrp network-id 1
ip nhrp holdtime 360
ip nhrp shortcut
ip nhrp redirect
ip tcp adjust-mss 1360
load-interval 30
shutdown
keepalive 10 3
tunnel source GigabitEthernet0
tunnel mode gre multipoint
tunnel key 1
tunnel protection ipsec profile My-Profile-v4 shared
interface Tunnel2
description ** DMVPN Intranet IPv6 **
bandwidth 1000
ip vrf forwarding VPN
ip address 10.0.12.1 255.255.255.0
ip mtu 1416
no ip next-hop-self eigrp 65351
no ip split-horizon eigrp 65351
ip pim sparse-mode
ip nhrp map multicast dynamic
ip nhrp network-id 2
ip nhrp holdtime 360
ip nhrp shortcut
ip nhrp redirect
ip tcp adjust-mss 1360
load-interval 30
keepalive 10 3
tunnel source GigabitEthernet0
tunnel mode gre multipoint ipv6
tunnel key 2
tunnel protection ipsec profile My-Profile-v6 shared
Regards,
ThomasHello Marcin,
it is working now :-)
First I was running a dual stacked spoke as well, but now I am using one IPv4 and one IPv6 only spoke. The ipsec profiles are "shared", because besides the two shown tunnels I have one more IPv4 and IPv6 Tunnel for Extranetuse. The Spoke sites use "shared" as well, because they build a backup VPN Tunnel to a second Hub router.
I have removed the "keepalive 10 3" from my Tunnel interfaces and rebooted the routers and everything is working now.
Here are my final configurations:
Crypto
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 14
crypto isakmp key cisco address 0.0.0.0 no-xauth
crypto isakmp key cisco address ipv6 ::/0 no-xauth
crypto isakmp keepalive 10 periodic
crypto ipsec transform-set My-Set esp-aes 256 esp-sha512-hmac
mode tunnel
crypto ipsec profile My-Profile-v4
description ** IPsec Profile fuer IPv4 Peers **
set transform-set My-Set
set pfs group2
crypto ipsec profile My-Profile-v6
description ** IPsec Profile fuer IPv6 Peers **
set transform-set My-Set
set pfs group2
Tunnel Hub Dual Stacked
interface Tunnel1
description ** DMVPN Intranet IPv4 **
bandwidth 1000
ip vrf forwarding VPN
ip address 10.0.10.1 255.255.255.0
no ip redirects
ip mtu 1416
no ip next-hop-self eigrp 65351
no ip split-horizon eigrp 65351
ip pim sparse-mode
ip nhrp map multicast dynamic
ip nhrp network-id 1
ip nhrp holdtime 360
ip nhrp shortcut
ip nhrp redirect
ip tcp adjust-mss 1360
load-interval 30
tunnel source GigabitEthernet0
tunnel mode gre multipoint
tunnel key 1
tunnel protection ipsec profile My-Profile-v4 shared
interface Tunnel2
description ** DMVPN Intranet IPv6 **
bandwidth 1000
ip vrf forwarding VPN
ip address 10.0.12.1 255.255.255.0
ip mtu 1416
no ip next-hop-self eigrp 65351
no ip split-horizon eigrp 65351
ip pim sparse-mode
ip nhrp map multicast dynamic
ip nhrp network-id 2
ip nhrp holdtime 360
ip nhrp shortcut
ip nhrp redirect
ip tcp adjust-mss 1360
load-interval 30
tunnel source GigabitEthernet0
tunnel mode gre multipoint ipv6
tunnel key 2
tunnel protection ipsec profile My-Profile-v6 shared
end
Tunnel Spoke IPv4
interface Tunnel1
description ** DMVPN Intranet IPv4 **
ip vrf forwarding VPN
ip address 10.0.10.2 255.255.255.0
no ip redirects
ip mtu 1416
ip pim sparse-mode
ip nhrp map 10.0.10.1 1.1.1.1
ip nhrp map multicast 1.1.1.1
ip nhrp network-id 1
ip nhrp holdtime 360
ip nhrp nhs 10.0.10.1
ip nhrp shortcut
ip tcp adjust-mss 1360
delay 1000
tunnel source GigabitEthernet0
tunnel mode gre multipoint
tunnel key 1
tunnel protection ipsec profile My-Profile-v4 shared
end
Tunnel Spoke IPv6
interface Tunnel1
description ** DMVPN Intranet IPv6 **
ip vrf forwarding VPN
ip address 10.0.12.2 255.255.255.0
no ip redirects
ip mtu 1416
ip pim sparse-mode
ip nhrp map 10.0.12.1 2001:1:1:1::1
ip nhrp map multicast 2001:1:1:1::1
ip nhrp network-id 2
ip nhrp holdtime 360
ip nhrp nhs 10.0.12.1
ip nhrp shortcut
ip tcp adjust-mss 1360
delay 1000
tunnel source GigabitEthernet0
tunnel mode gre multipoint ipv6
tunnel key 2
tunnel protection ipsec profile My-Profile-v6 shared
end
Thanks again
Thomas -
Dual stack on tunnel interface
Is it possible to run dual stack IP schemes over an ipsec-protected tunnel interface on IOS? I am able to assign the IPv6 addresses like a normal interface on both ends however when i try to ping across the tunnel with IPv6 there is no response. Here is an example of my config:
R1
interface Tunnel0
description Tunnel to R2
ip address 172.30.1.237 255.255.255.252
ip mtu 1400
ip nat inside
ip virtual-reassembly
load-interval 30
ipv6 address FE80::172:30:1:1 link-local
ipv6 address 2001:1::172:30:1:1/126
keepalive 5 4
tunnel source GigabitEthernet0/1
tunnel mode ipsec ipv4
tunnel destination 1.2.3.4
tunnel protection ipsec profile protect-gre
R2
interface Tunnel0
description Tunnel to R1
ip address 172.30.1.238 255.255.255.252
ip mtu 1400
ip nat inside
ip virtual-reassembly
load-interval 30
ipv6 address 2001:1::172:30:1:2/126
ipv6 address FE80::172:30:1:2 link-local
keepalive 5 4
tunnel source FastEthernet0/1
tunnel destination 1.2.3.5
tunnel mode ipsec ipv4
tunnel protection ipsec profile protect-gre
The only solution i can clearly see is running a separate tunnel, which i would like to avoid. Any assistance is greatly appreciated!Hello,
In my System preferences the IPv6 settings are set to "automatic", my DSL router (Cisco 787) supports IPv6. When visiting sites like www.sixxs.net and www.apnic.org (which are reachable by both IPv6 and IPv4), some pages are reached by IPv6 and some by IP4. Even the same page may load in IPv6 first, but a second time via IPv4. This behaviour has changed since my upgrade to Leopard, under Tiger the behaviour was much more stable.
Gerard -
Error in phase import Homogeneous system copy from a BI 7.3 dual stack ABAPJAVA
Hi
I'm doing a Homogeneous system copy from a BI 7.3 dual stack ABAP+JAVA system with an Oracle DB (11g version, 11.2.0.3.0 patch level) with AIX ibm OS.
Before starting export I've executed in the source system the report SMIGR_CREATE_DDL, as described in sap note 888210, and I generated *.SQL files.
After, during the import in the target system I get the following error message:
vi /expdb2/tmpDB0/sapinst_instdir/NW730/ORA/ORA/COPY/ORA/SYSTEM/STD/AS/import_monitor.log
INFO: 2014-03-08 00:21:57 com.sap.inst.migmon.LoadTask run_report
Monitor jobs: running 0, waiting 1, completed 60, failed 5, total 66 finish processing of package SAP0000
You can see below the detail of the 5 packages in error:
SAPAPPL0_1_5
DbSlExecute: rc = 99
(SQL error 2216)
error message returned by DbSl:
ORA-02216: tablespace name expected
(DB) INFO: disconnected from DB
/usr/sap/DB2/SYS/exe/uc/rs6000_64/R3load: job finished with 1 error(s)
/usr/sap/DB2/SYS/exe/uc/rs6000_64/R3load: END OF LOG: 20140307141347
SAPZPSA
DbSlExecute: rc = 99
(SQL error 2216)
error message returned by DbSl:
ORA-02216: tablespace name expected
(DB) INFO: disconnected from DB
SAPDODS
DbSlExecute: rc = 99
(SQL error 922)
error message returned by DbSl:
ORA-00922: missing or invalid option
(DB) INFO: disconnected from DB
SAPDFACT
DbSl Trace: Error 1741 in exec_immediate() from oci_execute_stmt(), orpc=0
DbSl Trace: ORA-01741 occurred when executing SQL stmt (parse error offset=8126464)
(DB) ERROR: DDL statement failed
( ALTER TABLE "/BI0/F0TCT_C01" ADD PARTITION "/BI0/F0TCT_C010000001131" VALUES LESS THAN ( 0000001131 ) TABLESPACE "" )
DbSlExecute: rc = 99
(SQL error 1741)
error message returned by DbSl:
ORA-01741: illegal zero-length identifier
(DB) INFO: disconnected from DB
SAPZOSO
DbSl Trace: Error 922 in exec_immediate() from oci_execute_stmt(), orpc=0
DbSl Trace: ORA-00922 occurred when executing SQL stmt (parse error offset=242024448)
(DB) ERROR: DDL statement failed
(CREATE TABLE "/BIC/B0000989000" ("REQUEST" VARCHAR2 (000090) DEFAULT ' ' NOT NULL, "DATAPAKID" VARCHAR2 (000018) DEFAULT '000000' NOT NULL, "PART
NO" NUMBER (000010) DEFAULT 0 NOT NULL, "RECORD" NUMBER (000010) DEFAULT 0 NOT NULL, "PLANT" VARCHAR2 (000012) DEFAULT ' ' NOT NULL, "MATERIA
L" VARCHAR2 (000054) DEFAULT ' ' NOT NULL, "RPA_CURUOM" VARCHAR2 (000015) DEFAULT ' ' NOT NULL, "RPA_MVF" NUMBER (000017, 000002) DEFAULT 0 NOT N
ULL, "PRICE_UNIT" NUMBER (000017, 000003) DEFAULT 0 NOT NULL, "RPA_QTYUOM" VARCHAR2 (000009) DEFAULT ' ' NOT NULL, "RT_SSMFGR" VARCHAR2 (000024)
DEFAULT '00000000' NOT NULL, "BASE_UOM" VARCHAR2 (000009) DEFAULT ' ' NOT NULL, "FRE_PLNPUR" VARCHAR2 (000036) DEFAULT ' ' NOT NULL, "FRE_MINS
TK" NUMBER (000017, 000003) DEFAULT 0 NOT NULL, "FRE_SERLEV" NUMBER (000017, 000003) DEFAULT 0 NOT NULL, "FRE_SELCLS" VARCHAR2 (000003) DEFAULT '
0' NOT NULL, "FRE_REPLST" VARCHAR2 (000006) DEFAULT ' ' NOT NULL, "ABCKEY" VARCHAR2 (000003) DEFAULT ' ' NOT NULL, "RECORDMODE" VARCHAR2 (000003)
DEFAULT ' ' NOT NULL, "RT_SERVLEV" VARCHAR2 (000003) DEFAULT ' ' NOT NULL, "RT_SUPS" VARCHAR2 (000003) DEFAULT ' ' NOT NULL, "VAL_TYPE" VARCH
AR2 (000030) DEFAULT ' ' NOT NULL, "PUR_GROUP" VARCHAR2 (000009) DEFAULT ' ' NOT NULL, "RT_VPNEU" NUMBER (000017, 000002) DEFAULT 0 NOT NULL,
"CURRENCY" VARCHAR2 (000015) DEFAULT ' ' NOT NULL, "RT_VRKPE" NUMBER (000017, 000003) DEFAULT 0 NOT NULL, "DISMM" VARCHAR2 (000006) DEFAULT ' '
NOT NULL, "SALES_UNIT" VARCHAR2 (000009) DEFAULT ' ' NOT NULL, "RT_VP_BT" NUMBER (000017, 000002) DEFAULT 0 NOT NULL, "RT_VPE_BT" NUMBER (000017,
000003) DEFAULT 0 NOT NULL, "RT_VP_NT" NUMBER (000017, 000002) DEFAULT 0 NOT NULL, "RT_VPE_NT" NUMBER (000017, 000003) DEFAULT 0 NOT NULL, "R
T_VWAERBT" VARCHAR2 (000015) DEFAULT ' ' NOT NULL, "RT_VWAERNT" VARCHAR2 (000015) DEFAULT ' ' NOT NULL, "RT_VPMEIBT" VARCHAR2 (000009) DEFAULT '
' NOT NULL, "RT_VPMEINT" VARCHAR2 (000009) DEFAULT ' ' NOT NULL, "LOC_CURRCY" VARCHAR2 (000015) DEFAULT ' ' NOT NULL, "UNIT" VARCHAR2 (000009)
DEFAULT ' ' NOT NULL, "CM_MCATDIV" VARCHAR2 (000054) DEFAULT ' ' NOT NULL, "CM_CDT1" VARCHAR2 (000054) DEFAULT ' ' NOT NULL, "CM_CDT2" VARCHAR2
(000054) DEFAULT ' ' NOT NULL, "CM_CDT3" VARCHAR2 (000054) DEFAULT ' ' NOT NULL, "CM_CDT4" VARCHAR2 (000054) DEFAULT ' ' NOT NULL, "CM_HIEID"
VARCHAR2 (000006) DEFAULT ' ' NOT NULL, "CPSTLC" NUMBER (000017, 000002) DEFAULT 0 NOT NULL, "CPSVLC" NUMBER (000017, 000002) DEFAULT 0 NOT NULL
, "STOCK_VAL" NUMBER (000017, 000002) DEFAULT 0 NOT NULL, "STOCK_QTY" NUMBER (000017, 000003) DEFAULT 0 NOT NULL, "RT_SEASON" VARCHAR2 (000012)
DEFAULT ' ' NOT NULL, "RT_SEASYR" VARCHAR2 (000012) DEFAULT '0000' NOT NULL, "CALDAY" VARCHAR2 (000024) DEFAULT '00000000' NOT NULL, "CALWEEK"
VARCHAR2 (000018) DEFAULT '000000' NOT NULL, "RF_BNDID" VARCHAR2 (000012) DEFAULT ' ' NOT NULL, "/BIC/ZCATTR3" VARCHAR2 (000006) DEFAULT ' ' NOT
NULL, "/BIC/ZCSTYLE" VARCHAR2 (000006) DEFAULT ' ' NOT NULL, "/BIC/ZCIMAGE" VARCHAR2 (000006) DEFAULT ' ' NOT NULL, "/BIC/ZCBRNDTYP" VARCHAR2 (000
003) DEFAULT ' ' NOT NULL, "/BIC/ZCGROUPE" VARCHAR2 (000054) DEFAULT ' ' NOT NULL) PCTFREE 10 PCTUSED 00 INITRANS 001 TABLESPACE STORAGE (
INITIAL 0000000016 K NEXT 0000001024 K MINEXTENTS 0000000001 MAXEXTENTS 2147483645 PCTINCREASE 0000
FREELISTS 001 FREELIST GROUPS 01) PARTITION BY RANGE ("PARTNO") ( PARTITION "/BIC/B00009890000000000002" VALUES LESS THAN (00000
00002) NOCOMPRESS ) )
DbSlExecute: rc = 99
(SQL error 922)
error message returned by DbSl:
ORA-00922: missing or invalid option
(DB) INFO: disconnected from DBhello,
Before anything update DB shared lib, R3load, R3ldctl and R3szchk in the target system. Also Check in source system if you have any tables o index missing in db02 transaction, If this system wa upgraded from a previous release please check TAORA and IAORA tables in source system and check all the tablespaces named in those tables are created in the target system.
let me know how it goes.
Regards,
Michael -
Dual Stack NW 7.0 installation with R/3 Backend as UME
I have a quick question guys. I am about to install a dual stack NW system with ADS(SQL server database on windows) and will use a R/3 Enterprise running on unix as the UME datasource. Now this R/3 enterprise backend already acts as bakend for Portal system and uses sap logon tickets and as such already has the user SAPJSF. Now when i actually perform the NW 7.0 installation and enter a master password during the course, would this override the SAPJSF user in R/3 backend system at all.
What are the general problems that are caused with using an existing ABAP only system as the UME for your Java stack(Dual stack actually) systems. Can you advise.
Regards
KalyanHi,
Now when i actually perform the NW 7.0 installation and enter a master password during the course,
would this override the SAPJSF user in R/3 backend system at all.
NO....Not at all..
SAPJSF user is used for the communication between ABAP and JAVA stacks. SAPJSF user is an independent user of each independent ABAP stack.
ABAP data/user-store is the place where the users, roles and authorizations of an ABAP System are stored.
And with the same concept, the UME is the same mechanism for users, roles, permissions of an JAVA system.
After installation of your new NW ABAP+JAVA Stack, you will have to specify the SAPJSF user of ur old R/3 ABAP system which you want to use as User Data Store for ur Newly installed Java System's UME.
In ABAP System section u will have to provide all details of ur SAP R/3 application server, which ur portal is already using as User Data Store.
What are the general problems that are caused with using an existing ABAP only system
as the UME for your Java stack(Dual stack actually) systems. Can you advise.
It depends on the usage of your new application server.
Regards
Bhavik G. Shroff -
Question about the number of ERS instances in a dual-stack MCS environment
Hello to the group.
I have a simple question for those running a NetWeaver 7.0 (i.e. 2004s) dual stack (ABAP/JAVA) setup in an MCS environment. On each individual node, do you have two separate ERS processes running on the node (as seen in Task Manager) that is opposite to the system running the ASCS/SCS instances? If so, do you have a set of profiles for each of these ERS processes (I am guessing that is true)?
Thanks in advance for your help.
J. HaynesHas anyone found a good description of the process that runs after one node fails over to another one? help.sap.com mentions that the ASCS will restart and run the command enstatus.cmd but I cannot find what is supposed to happen after that. Is the ERS service itself stopped?
Thanks
J. Haynes -
hi guys,
we plan to upgrade Enterprise Dual stack(ABAP+JAVA) System to EHP4 system.
In EHP4 upgrade document it says, No dual stack supported for EHP4 installation..was that mean
only for Installation or upgrade too.
Seperate SID is required for EHP4 system after upgrade? Please confirm.
thankshi jaichan,
yes, you are right ..For new installation of SAP ERP to EHP4 level, you cannot install dual stack system..i have read in sap note 855534..please find below the extract from this note:
As of SAP Business Suite 7, you can no longer install Dual Stack Application Systems (ABAP+Java).
If you want to use both SAP Business Suite ABAP and Java Components in your system landscape, you have to proceed as follows:
1. Install a separate ABAP-based SAP Business Suite system.
2. Install the required Java components in a separate Java-based SAP system.
3. Configure the connection of the Java-based SAP system to the ABAP-based SAP Business Suite back-end system.
The SAP Business Suite 7 comprises: EHP4 for SAP ERP 6.0, SAP CRM 7.0, SAP SCM 7.0, SAP PLM 7.0, SAP SRM 7.0
As of now you will find the latest recommendations at a central place in SDN:
https://www.sdn.sap.com/irj/sdn/landscapedesign -> Distribution Models
You will also find information about the deployment of SAP NetWeaver usage types and the SAP Business Suite there.
but you can upgrade your previously installed SAP ERP dual stack system without having seperate SID's thing...
We have upgraded around 50 of our systems without any problem
thanks sunny -
PI 7.1(dual stack) and PI 7.31(Single stack) -
Friends,
I have a proxy to proxy scenario - Proxy --> PI --> Proxy
We have two servers PI 7.1(dual stack) and PI 7.31(Single stack)
i did the development in ESR and my ESR is pointing to PI 7.1, when i execute the scenario i receive one error message "receiver could not be determined", i ensured that all my input is correct, still i get the same error message.
the expectation is my scenario should point to PI 7.31, Can some one help me where and what settings i need to make in-order to make it work.
Please Note: All my data is correct and i read some scn forums wherein they asked to refresh the cache , i have refreshed the cache also still the problem persists.
Thanks in advance!Iñaki Vila
Communication component in ID is the same as sender side.
could you share your sender configuration?
Did you mean Tcode - SXMB_ADM and under that Sender/Receiver configuration
Krupa Rao Atluri
In ID steps are correctly defined.
I spoke to my colleague he hinted that at RUN TIME we want to point to PI7.31, he mentioned config change needed in SXMB_ADM
any further inputs from any one could be useful. -
Mapping error in PI 7.4 dual stack
Dear Experts,
Recently we upgraded our system from PI 7.1 to PI 7.4 dual stack.
Scenerio is ECC->PI->SOAP(Webservice) synchronous
Issue in detail:
We are creating a invoice in ECC system through PI its updating in third party site using SOAP webservice and will get a reference number from that site and then updating in ECC as in synchronous way.
Invoice data's are reached PI sucessfully from ECC but it not updating in the site and getting below mapping error after upgarded to PI 7.4.
Your points will be highly appreciable.
Kindly help to sort out this issue.
Best Regards,
MonikandanHi Monikandan,
It seems you are trying the sign the payload in your java mapping. So, looking at the attached error, there could be 2 possibilities:
1) Either there is no certificate with alias: *_PRD
2) This certificate is stored in some "System" type keystore view which is not accessible from you mapping code. Try to move your certificate to some "User" keystore view.
Thanks & regards,
Piyush
Maybe you are looking for
-
How to make hyperlinks in PDF doc open in a seperate PDF window?
I created a "Main" PDF document and have various attachments in it including PDF. I created them with Insert, Hyperlink. That works, however, if I have the main document open in PDF, and I click on one of the hyperlinks to open a PDF document, the m
-
Hi, I have a java J2ee project, with spring integrated. I have set up the project so that I can make calls from flex mxml files to spring managed objects. This works as expected. My project deploys so that I have the following folder and file hierarc
-
Archieve/Backup emails in Mail??? HOW???
Okay this will get flamed I'm sure but I'll be damned if I can find any info on how to archieve email using mail? I know in outlook you just click Archieve and presto it archieves selected emails, how do I archieve in mail I've tryed Help in OSX noth
-
Flash version 10.0.32.18 and Internet Explorer 7 issue.
Hello, Have downloaded the "install_flash_player_10_activex.msi" and created an installation package with the settings in mms.cfg file of "AllowUserLocalTrust=1, AutoUpdateDisable=1, AVHardwareDisable=1" and tested in Windows XP with SP3 with IE6 and
-
3D Objekte aus Photoshop CC 2014 in After Effects CC 2014
Hallo, ich hätte eine kurze Frage zum hin und her von 3D Objekten in CC 2014: Ich habe mir in Photoshop einen Planeten erstellt, 3D Kugel mit eigener Textur, alles easy. Den wollte ich nun wie gewohnt in After Effects importieren und animieren - und