Cisco 7200 ip interface issue

I have a 7200 already configured with a cable modem interfaces working just fine with ios ver 12.2(15)BC2e. 
I just got another 7200 with the same cable card with ios ver Version 12.2(33)SCB4 for another site
the plan was to simply copy the working config to this one and walk away.
unfortunately i can no assign an ip to the cable interface, but successfully assigned an ip to the gig interface.
the only clue i can see is the out from the new 7200
BC_CMTS#sh ip int cable 3/0
Cable3/0 is administratively down, line protocol is down
  Internet protocol processing disabled
any ideas would be greatly appreciated,

thanks for the quick reply.  the port was disabled at that point and time, but has nothing to do with the issue.
quite simply put, when i try to configure an ip address on the cable card, i get the typical "
% Invalid input detected at '^' marker." error message.  When I type "ip ?" under that interface there is no address option.
just to recap this config works just fine on my other 7200 and cable card, but this 7200 has a newer IOS.
any insight or ideas would be greatly appreciated.
regards

Similar Messages

  • Does Cisco Media Services Interface mark RTP and Signaling packets regardless of Cisco Prime Collaboration/MediaNet Deployment?

    Hi there,
    I'm deploying Cisco UC Integration Lync 9.2(5). There's a QoS portion which states that you can install Cisco Media Services Interface on the user's PC and is to be used with Cisco Prime Collaboration or MediaNet:
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucilync/9/CUCI_BK_C0545A41_00_cisco-uc-integration-for-microsoft/CUCI_BK_C0545A41_00_cisco-uc-integration-for-microsoft_chapter_010.html#CUCI_CN_IDBE72E9_00
    If we don't have Cisco Prime Collaboration or MediaNet, does Cisco Media Services Interface mark RTP and Siganling packets on the outbound regardless? Or do I have to manually set the DSCP values for the PC?
    Thanks,
    John

    When you were placing the internal test calls, where was your phone located?   The RTP streams are usually only set up between the two endpoints (assuming no transcoder or MTP is used).
    Have you have already checked calls between IP phones at your central site (where Unity is located) and IP Phones at site A?   Are these working fine?   If not, then it's likely you do have a QoS issue over the WAN to Site A.
    Have you confirmed whether or not calls from the PSTN gateway at site A experience any voice QoS issues when transferred to an IP Phone at the central site?
    Is the same codec is being used for the MGCP gateway as for IP Phones at that site (check the Region settings for the Device Pool it's in)?
    If these things have all been checked, then you may want to consider collecting a simultaneous sniffer trace from each end of a single call, and comparing what's seen at the two endpoints.
    Kind regards,
    Craig

  • GETVPN Key server Cisco 7200

    Hi,
    I am using Cisco 7200 NPG1 as Key server for GETVPN. I have almost 500 Spokes. How many concurrent IKE sessions could be supported by 7200 box ?
    I have heard that simultenous session limit for IKE is 100 ?
    regards
    Prasad K

    I have heard that simultenous session limit for IKE is 100 ?
    This is true to software crypto.
    You get best scaling factor on 7200 with VSA. 500 seems a decent number. Are you seeing any problems?

  • Are USB audio interface issues on iMac Haswell resolved?

    HI,
    i just ordered a 27 inch iMac, maxed out with a 1TB SSD.
    I noticed the imac doesn't have an audio in jack and figured i'd shop for a good USB Audio Interface.
    But then i came across all these USB audio interface issues on the new iMac.
    This is incredible to me because iMacs are often used by creative people and lots of musicians.
    For me audio is VERY important. I record music and i record sound for animation and video.
    Apple thus far seemed to be avoiding the topics and issues at hand.
    Are the USB audio issues resolved? What was resolved? What was the problem (Maverick? Fusion Drive)?
    Is it wise to choose for a Thunderbolt Interface? Which one?
    Any help would be hugely appreciated.
    Especcialy since it seems such a wide spread problem.
    Thanx

    doubt it would be a general issue
    usb is a universal serial bus it always require a driver for anything
    and the driver of one external audio device would act different then the driver from another external audio device
    so it would be very unlikely that an external audio card using a cirrus logic audio chip would cause the same issues with the imac as one with a realtek or soundblaster audio chip
    not that there could not be issues with all of them but not likely that they would suffer from the same issue

  • How to Gatekeeper on cisco 7200

    How can i enable my gatekeeper on cisco 7200 my current IOS is 12.1.(2)T i cannot enable my gatekeeper it seems to be working before.
    hope you can help me.
    thanks

    Does rolling back to previous version help. If so you could search for any potential bugs in 12.1.(2)T or try loading the latest version.
    My search on bug toolkit with "Gatekeeper" keyword on this release got me 240 bugs. I am not sure which one is yours. So better try with the latest version

  • Multilink limitations application on Cisco 7200 Series

    Hi,
    Can someone please mention if Multilink can be supported on Cisco 7200 Series?
    IOS version:
    IOS 7200 Software (C7200-P-M), Version 12.3(16a), SOFTWARE (fc2)
    cisco 7206VXR 
    Any comment will be appreciated.
    Thank you.

    Hi -
    Our s/w development group is in the process of implementing ipv6 support in our products, and would like to use our Cisco 2650XM running ITP s/w for ipv6 interoperability tests.
    However, it appears that ipv6 is not supported in this s/w version:
    ITP1#sh version
    Cisco IOS Software, C2600 Software (C2600-ITPK9-M), Version 12.4(15)SW2, RELEASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Tue 23-Sep-08 19:48 by prod_rel_team
    ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
    ITP1#config
    Configuring from terminal, memory, or network [terminal]?
    Enter configuration commands, one per line. End with CNTL/Z.
    ITP1(config)#ipv6 ?
    % Unrecognized command
    My question is: Can I use this s/w version on the 2650XM in an ipv6 network? Do I need to upgrade the s/w?
    Thanks,
    Matt

  • Building Cisco 7200 VXR

    Hi,
    I have a Cisco 7200 VXR chassis. What cards I have to buy to mount a VoIP Gateway, with SS7 E1 ports to trunk with the PSTN networks?
    Best Regards.

    You can use Cisco MIX-enabled T1/E1 Port Adapter. For more information kindly refer the url's below,
    http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00800afd65.shtml
    http://www.cisco.com/en/US/products/hw/modules/ps2033/ps1952/index.html

  • Cisco 7200 as managed cpe with mpls enabled

    Is there any real network that is using managed CPE (CPE router managed by SP) with mpls enabled (MPLS-TE, VPN) etc.
    Is anybody using cisco 7200 as a managed cpe router with mpls.
    Thanks.
    subodh

    with PE router, Service provider handles so many CE routers (of customers).
    Managed CPE router will be placed at the customer site and will handle only one customer.
    Is there any company/customer that have so big network that they need cisco 7200 at there site and this CPE does MPLS-TE,MPLS-VPN.
    could u pl. name some companies that are availing this king of services from service provider.
    {as cisco 7200 is also capable of providing voip solution to customer}.

  • Cisco 7200 as BRAS

    Hi,
    does anyone of you know if you can use a Cisco 7200 as a BRAS? We were told it is possible, but I am not able to find an IOS image with PPPoE support.
    Any pointers are welcome.
    TIA
    NaNa

    As far sa I know, you can get ISG
    (http://www.cisco.com/en/US/products/ps6566/products_configuration_guide_book09186a008061ab53.html)
    features on 7600 platform but only for IP sessions, not for PPP.
    These functions should be available on on SIP-400.

  • Two storage box (3510 and 6140) interface issue...

    Hi All,
    In my setup we were previously used storage box 3510 but having space issues we are purchasing new storage box of six series 6140. Now, I don't have any clear idea that both the storage can easily mounted on the servers? or there are some interface issues might be?
    Can anyone suggest me what are the points(like network, HD and etc.) I have to consider for the compatibility of these storage box?
    Thanks...

    Hi user505
    Now, I don't have any clear idea that both the storage can easily mounted on the servers? or there are some interface issues might be?How many HBA's do your current hosts that are connected to the 3510 have ? are they are single port single card or dual ported card ?.
    Depending on how many HBA's you have in your server I would configure up the 6140 with the initiators , map the new volumes straight to the server and then do your copying of data.
    In regards to network config etc you'd need to setup the 6140 as per the normal configuration for out of band access , so you can get it via CAM.
    Hope that helps
    David

  • Cisco SUP MGMT Interface Support L2 switchport mode?

    Does the Cisco Supervisor MGMT interface support to be converted to a switchport to be assigned to a specific VLAN? The same question for 3750 switches and other switches.

    No. They do need to have an IP address configured as they are actually routed ports.
    The address needs to be in the subnet associated with the VLAN it plugs into in the switching infrastructure.

  • Cisco ISE Web interface Login

    Hi,
    Can anyone help me in resetting the Cisco ISE web interface password. I'm able to login to CLI of ISE but couldnt use the same credentials to login to web interface. Is there any way to reset this web interface password through ISE CLI?
    Thanks
    Daniel

    Daniel,
    Just ran across your question, the answer is you can have login credentials for the cli but that is seperate from the gui. The way I understand it is once you get to the gui for the first time user is admin and password is cisco. At this point you are required to put in a new password. Once in the gui other users can be created for the gui.
    Erik

  • Possible interface issues on cisco 3725 router

    I have a router that has been working great for almost 2 years now, has had the occisonal reset due to power failures but, I have not adjusted the configuration for a long time, until today trying to diagnose the issue thats occuring.
    Here is the setup, a Cisco 3725, with three network interfaces, FE 0/0 connected to cable modem, FE 0/1 connected to the 10.0.1.x and FE0/1.10 vlan for call manager express ip phones. I then have a third interface FE 1/0 that acts as my DMZ where I keep servers. Both FE 0/0 and FE 1/0 are behind the NAT. Just yesterday I noticed that the internet traffic stops on the FE 0/1 interface after a few hours local VLAN routing works from FE0/1 to FE 1/0 and I can ssh into the router just no web traffic, I reset and it starts working again, odd thing is the DMZ still has internet during this entire time, which makes me think the interface is faling. Is there any logs or commands I can do when the interface fails again to see if its a bad interface on the router?
    I isolated the switch out of the question, hooked a non managed switch up while the internet was not working and tried to connect and got nothing as well.

    Try the below and see whether that works
    The inside interface of the PIX cannot be pinged from the other end of the tunnel unless the management-access command is configured in the global configuration mode.
    PIX-02(config)#management-access inside
    PIX-02(config)#show management-access
    management-access inside

  • Cisco 7200 VSA issue after upgrade to IOS 15.2

    After upgrade to IOS 15.2(4), VSA module in 7206VXR (NPE-G2) is disabled and we cannot enable it.
    Show diag output:
    ------------------ show diag ------------------
    Slot 0:
    VSA IPsec Card Port adapter
    Port adapter is deactivated
    Port adapter insertion time unknown
    EEPROM contents at hardware discovery:
    PCB Serial Number        : JAF1309ADDT
    Hardware Revision        : 1.0
    Part Number              : 73-10220-05
    Board Revision           : B1
    RMA Test History         : 00
    RMA Number               : 0-0-0-0
    RMA History              : 00
    Deviation Number         : 0
    Product (FRU) Number     : C7200-VSA          
    Version Identifier       : V01
    Top Assy. Part Number    : 68-2578-05
    CLEI Code                : CNUCAFNAAA
    EEPROM format version 4
    EEPROM contents (hex):
      0x00: 04 FF C1 8B 4A 41 46 31 33 30 39 41 44 44 54 40
      0x10: 05 0D 41 01 00 82 49 27 EC 05 42 42 31 03 00 81
      0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 43 37 32
      0x30: 30 30 2D 56 53 41 20 20 20 20 20 20 20 20 20 20
      0x40: 20 89 56 30 31 20 D9 03 C1 40 CB 87 44 0A 12 05
      0x50: C6 8A 43 4E 55 43 41 46 4E 41 41 41 FF FF FF FF
      0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
      0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
    If we try to enable it manually from CLI we get the following message:
    Router(config)#crypto engine slot 0
    VSA will NOT come up until system power-cycle or reload
    Of course, after reload nothing happens.
    Is VSA incompatible with IOS 15.x? I'm asking because downgrade to 12.4 causes VSA to be active again.
    Regards,
    Igor

    Hi igor,
    1) FDP image
    Field-programmable devices (FPDs) are hardware devices implemented on router cards that support separate software upgrades. An FPD image package is used to upgrade FPD images
    The FPD image package must be compatible with the Cisco IOS software that is running on the router. If an incompatibility exists between an FPD image package and the Cisco IOS software release running the router, the device with the FPD will not operate properly until the incompatibility is resolved.
    The FPD automatic upgrade feature searches only for the FPD image package file that is the same version number as the Cisco IOS release being used by the system. For example, if the Cisco IOS release being used is Cisco IOS Release 12.4(5)T1, the system searches for the FPD image package file that supports the specific Cisco IOS release (c7200-fpd-pkg.124-5.T1.pkg).
    2) Steps to Upgrade:
    From the document below which I already sent you, please refer to the section “How to Upgrade Field-Programmable Devices”
    http://www.cisco.com/en/US/docs/routers/7200/configuration/feature_guides/fpd.html
    I would recommend you to follow the steps in the “Field-Programmable Device Quick Upgrade (Automatic FPD Upgrade Only)” as that is the recommended and the easiest way.
    Steps are:
    The command is present “upgrade fpd auto” in the running-config by default.
    Have the Cisco IOS image in disk2:
    Download the FPD image package to disk2: flash disk
    Reboot the router using the new Cisco IOS release.
    Hope this helps
    Thanks
    Syed

  • Cisco ASA 5505 performance issues on downloads - data into the ASA from the Internet

    I have having serious issues with performance on my ASA 5505s that I am testing with 9.2.3 code.
    I stripped the config and removed as much stuff as I could - no VPN etc. and I am ONLY getting about 30-40Mbps downloads from sites but 95Mbps uploads????  Anyone else seeing these problems?   If I remove the firewall my PC can hit 300/300Mbps to the same sites using the same switch and cable.
    I installed 1Gb of mem on the ASA 5505 but it made no difference. The ASA has a UL IP Security license but I am only using and inside and outside address for these tests, no other ports configured.
    Is anyone else seeing this performance problem with the 9.2.3 code?  I went to this from 8.2.5 to try to resolve QOS failure bugs that I found in the 8.2.5 code. I did not expect to have a performance hit though and it is only on downloads TO the ASA from the Internet from all speed test sites that I try. Uploading speeds seem fine. No access-lists on my interfaces either...barebones config.
    My FIOS and switch interfaces are fine...no errors on any interfaces and the same switch interface hits 300/300Mbps when my laptop is directly attached. 
    Anyone have a barebones config on their ASA 5505 that flies...I will try it on mine and see if some command somewhere (hidden) is causing the issue. I even cleared the config and started with a clean slate just in case I was missing some command from the older configs that may have impacted performance.

    After changing the switch with a high end switch my performance increased but I am still not happy with the throughput out of my ASA. I have about 50+ ASAs 5505s and a dozen 5510s. Most remote sites have 5505s. All my sites right now have 8.2.5-51 and I wanted to put 9.2.3 out there to solve issues I have uncovered on the 8.2.5 code with regards to QOS issues.
    I get much better results using the Cisco 3750X attached to the FIOS  (right around 300/300 with my laptop directly attached to the 3750x bypassing the ASA - my FIOS circuit rating is also 300/300).  Going through the ASA to the same test site I get download speeds of 35 to 75. Changes randomly which really bothers me. My uploads speeds are ALWAYS faster then my download speeds.  Example - best download I would ever get is 75Mb and my upload would usually hit 95Mb during the same test period.
    I may have to live with it but the inconsistency is what really bothers me.
    Here is the config I am currently using. Nothing going on during testing since only a single PC is attached. VPN tunnel to the main site can be up or down...doesn't seem to make any difference. PC does to site directly from outside interface of ASA...split tunneling. Even when I removed tunnels and tested with just the ASA as a firewall to the Internet I was still seeing the same inconsistencies.
    Anything obviously  missing - new command or anything?   Xlates causing issues?

Maybe you are looking for