Cisco 7600 in MPLS

Hello,
1)
I have a question regarding Cisco 7600/6500 ( sup720 exactely) in MPLS.
I've read in documentation and also in some forum posts that "show mpls cef" is not MPLS aware command and should be used only for IP traffic. But still in some Cisco documents you can find that it is recommended on Cisco 7600/6500 for MPLS to use show mls cef instead of show ip cef (wether it is P or PE device in MPLS).
Does anyone know what is true?
2)
Also when load balancing is involved in MPLS with Cisco 7600/6500 (sup720)
P=======PE (P and PE are 7600 and there are two paralle link with the same cost between them).
In documentation can be found that in MPLS, CEF is still in charge for load sharing (src-dst IP header based) except for hardware based platforms.
Since 7600 is hardware based platform does it have some other load sharing method or it is also CEF based?
Thanks in advance.
Regards,
A.

Hi Prima,
This question has been already answered several times and the answer is still the same :-) : it's not supported on 7600 platform due to hardware limitation.
HTH
Laurent.

Similar Messages

Cisco 7600 MPLS and set Qos group

Hi, i'm am trying to use to following class-maps and policy maps on a Cisco 7600. The same maps have been used on both 3700 series and 7200 series. However when i try to apply IP_TO_MPLS_OUT and MPLS_TO_IP_IN on the 7600 (with SUP32 and 48 port gigabit blade) i get a message on the console
"set qos group" not supported.
I used the QoS group to carry the MPLS EXP value (as label would is popped) and this works well.
How can i get the QoS group to work on the 7600, if not is there a valid workaround?
Many thanks for your help.
policy-map IP_TO_MPLS_OUT
class qosgrp5
set mpls experimental topmost 5
priority percent 10
class qosgrp4
bandwidth remaining percent 50
set mpls experimental topmost 4
class qosgrp2
bandwidth remaining percent 20
set mpls experimental topmost 2
class class-default
bandwidth remaining percent 30
random-detect
set mpls experimental topmost 1
policy-map CE_OUT
class qosgrp5
set ip precedence 5
class qosgrp4
set ip precedence 4
class qosgrp2
set ip precedence 2
policy-map MPLS_TO_IP_IN
class MPLS_EXP5
set qos-group 5
class MPLS_EXP4
set qos-group 4
class MPLS_EXP2
set qos-group 2

Hi,
I'm not aware that you can use qos groups on c7600 (LAN ports ?).
For the MPLS_TO_IP direction you can use 'mpls propagate-cos' on the egress interface as workaround. This rewrites the egress IP ToS with the internal DSCP (which is inferred from the topmost MPLS label).
For the IP_TO_MPLS direction you could just match on the original DSCP ?
cheers,
Stefan

Configuring SYNCE/PTP on Cisco 7600 and Cisco MWR for NSN NodeB

Hi to All,
I would to ask for support on how i can establish the PTP between Cisco MWR 2941-DC and a NSN NodeB. The Cisco MWR is connected to a Cisco 7600 with SPA-2X1GE-SYNCE where the SSU/OSN clock is connected on the BITS ports. Hope you can assist me with the configurations.
Thanks,
Eugene

Dear Genedeath,
I have noticed that you posted this message since last year ..... have you ever been able to solve the case??
I had a glance to the diagram and it looks quite similar to my case.
I need to configure a Cisco MWR2941 for the very first time in order to support SyncE for packet Abis between a NSN FlexyBSC and a NSN BTS.
BTS---------------Gig x/y MWR Gig x/x-----------------------FlexyBSC
I guess the source clock would be provided by BSC...
Can you support me according to your experience ??
thanks and regards!
Mauro

Cisco 7600 Series Ethernet Services cards types & queue values

Hello,
There is different types for the Cisco 7600 Series Ethernet Services cards.
( More expensive cards with high queue values and less expensive cards with
low queue values.)
http://www.cisco.com/en/US/prod/collateral/routers/ps368/data_sheet_c78-549419.html
Hardware queues
ES Plus XT 40G line cards
• 128,000 ingress queues
• 256,000 egress queues
ES Plus XT 20G line cards
*• 64,000 ingress queues*
• 128,000 egress queues
Hierarchical QoS (H-QoS)
http://www.cisco.com/en/US/prod/collateral/routers/ps368/data_sheet_c78-570730.html
Hardware queues
Cisco 7600 Series ES Plus Transport 40G and 20G Line Cards
*Supporting up to 16 level 4 queues per physical port*
Hierarchical QoS (H-QoS)
Low queue cards have got only 4 queues per physical port. High queue cards
have got minimum 64.000 queue. This is very huge difference. In what kind
of scenario do we have to use the High queue cards ? Could you give some
examples please ? Kind Regards.
Burak

HI Burak,
Each time you configure a class with bandwidth allocation or shaping,.. a queue will be used so if you use such card to provide QoS for a lot of subscribers sharing the same interface, you will need a lot of them !!
HTH
Laurent.

Cisco 7600 Series (7603) Router Information

Hello,
Does anyone have a link or reference to a good description of the Cisco 7600 boot process and various memory heirarchy functions? I'm looking for information on what should be in NVRAM, FLASH, SUP-BOOTFLASH etc. Thank you.

You can find all the 7600 series router info here.
http://www.cisco.com/en/US/products/hw/routers/ps368/products_data_sheet0900aecd801c5cab.html
http://www.cisco.com/en/US/products/hw/routers/ps368/prod_literature.html
HTH,
Sundar

Cisco 7600, SCE8000, Etherchannel

I have two Cisco 7600 and 4 Cisco SCE8000.
I try connect two 7600 through etherchannel with sce.
I read MGSCP design guide and configured src-ip load-balance on one 7600 and dst-ip on another 7600.
I tested by test etherchannel load-balance command, IPs are use same interfaces on etherchannels.
But I see all numbers of sessions on each SCE but not 1/4 of all sessions.
What may be wrong in configuration?

After I wrote to config Cisco SM command force_subscriber_on_one_sce=true and restarted SM, I have 100% control CPU utilization on SCE and high CPU utilization of SM server.

Cisco 7600 Series can't back up it's config using Ciscoworks

We have a problem with Ciscoworks. Our client's Cisco 7600 can't back up it's configuration with Ciscoworks, while the rest of the devices can. They are all enrolled and discovered in the Ciscoworks of our client. Do you have any idea how to troubleshoot this? Thanks!

Have you partitioned the drive and formatted it Mac OS Extended (Journaled?) If not, try that and see if it helps:
Extended Hard Drive Preparation
1. Boot from your OS X Installer Disk. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
Steps 4-6 are optional but should be used on a drive that has never been formatted before, if the format type is not Mac OS Extended, if the partition scheme has been changed, or if a different operating system (not OS X) has been installed on the drive.

Viewing MAX-reseved-bandwidth on Cisco 7600 router

Hi everybody
I have been searching a command that will shows us the max-reseved bandwidth ( In the context of QOS) on cisco 7600.
I appreciate your help
Thanks
ciscoR1#show version
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.1(3)S5, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 12-Feb-13 13:17 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.1(3)S5, RELEASE SOFTWARE (fc2)

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
I'm uncertain, but on a 7600 with 15.x IOS, it's likely QoS is following the HQF changes, and if so, max-reserved-bandwidth has really been deprecated.

Catalyst 6500/Cisco 7600 MIB's

Could anyone tell me all MIB's I need to manage a Catalyst 6500/Cisco 7600? Or better, do you know any documents where I could find this information?
Thanks for your help.

You can get all these MIBs from http://www.cisco.com/public/mibs
As for what MIBs you need, it depends on what you're trying to poll.

Port Analizer Port gigabit cisco 7600 SIP-400 SPA-5X1GE-V2

Hi,
I have a Wan LINK (Layer 3), so I want to check if there are retransmissions in this link.
Do you know if there is a way that a can do SPAN on a GigabitEthernet Port on SPA-5X1GE-V2 (Cisco 7600 Platform)
I tried but i got this error:
R(config)#monitor session 10 source int GigabitEthernet 4/0/0
% Interface(s) Gi4/0/0 not supported as monitor source(s) on this platform
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.1(2)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
4    0 4-subslot SPA Interface Processor-400 7600-SIP-400
5    2 Route Switch Processor 720 (Active)    RSP720-3CXL-GE
4/0 5xGE SPA                    SPA-5X1GE-V2
thanks for the Help.

Hi,
Does anyone have any suggestions?

Cisco 7600 ES Plus Intelligent Services Gateway License-For old and new 7600-ES+20G3CXL= line card

Hi everyone
i had an one thing, that i don't understand clearly.
We had Cisco 7609-S witth 7600-ES+20G3CXL line card and Intelligent Services Gateway License (76-ES+ISG-LIC)
Now the Line card had hardware problem, and my manager not alllow me to buy services, He want to by the brandnew one.
I read some informations from cisco website " The license is purchased per chassis in increments of 8000 subscribers requiring BNG features with 8 MPLS VPNs per license".
But i don't know clearly that can we use the existing 76-ES+ISG-LIC with the New Line card? or I must buy the both of things
Anybody can support me?
Thanks
Phai La Quy

Hi everyone
i had an one thing, that i don't understand clearly.
We had Cisco 7609-S witth 7600-ES+20G3CXL line card and Intelligent Services Gateway License (76-ES+ISG-LIC)
Now the Line card had hardware problem, and my manager not alllow me to buy services, He want to by the brandnew one.
I read some informations from cisco website " The license is purchased per chassis in increments of 8000 subscribers requiring BNG features with 8 MPLS VPNs per license".
But i don't know clearly that can we use the existing 76-ES+ISG-LIC with the New Line card? or I must buy the both of things
Anybody can support me?
Thanks
Phai La Quy

Cisco Prime LMS MPLS monitoring

Hi all, have anyone used Cisco Prime LMS for MPLS xconnect monitoring?
Currently when these traps arrive to Cisco Prime LMS they are classified as "InformAlarm Unidentified Trap Generic".
Is it maybe possible to load the correct MIB for these traps and get Cisco Prime LMS to understand them correctly?
The raw traps looks like this:
xconnect down:
09:58:42.352760 IP (tos 0x40, ttl 245, id 12, offset 0, flags [none], proto: UDP (17), length: 114) routerhost.51591 > lmshost.snmptrap: [udp sum ok] { SNMPv1 { Trap(71) E:cisco.10.106.2 10.130.1.13 enterpriseSpecific s=1 424011509 E:cisco.10.106.1.2.1.26.2=2 E:cisco.10.106.1.2.1.26.2=2 } }
xconnect up:
09:59:48.597894 IP (tos 0x40, ttl 245, id 14, offset 0, flags [none], proto: UDP (17), length: 114) routerhost.51591 > lmshost.snmptrap: [udp sum ok] { SNMPv1 { Trap(71) E:cisco.10.106.2 10.130.1.13 enterpriseSpecific s=2 424018144 E:cisco.10.106.1.2.1.26.2=1 E:cisco.10.106.1.2.1.26.2=1 } }
I found some more info about the traps at:
http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&mibName=CISCO-IETF-PW-MIB-V1SMI
BR /Crille

Here is an update:
After discussing with TAC there seems to be 2 possible solutions in LMS right now:
1. Create a threshold that monitors the specific OID for the xconnect vc and generate alarm if it changes.
2. Configure the device to send syslog when a xconnect state changes and create an "automated syslog action".
I have not tried either of them yet so I dont know which one works best, but option 2 seems easiest (its a one time config).

6500 or 7600 for MPLS ?

Hi,
as I look to the characteristics of these 2 products they are quite similar if using supervisor engine 720. They both share several modules, interfaces...
The main requirement for us is to have full MPLS functionalities. Do you (experts) have a preference according to your appreciated experience ?
Regards.
Yannick.

hi
i think contrast to pfc3b and pfc3bxl is volume of memory,pfc3bxl has 1G memory. if you need more vpn you need more memories.
i have once installed pfc3a for customer mpls vpn. i config 7609 with pfc3a for PE function, and config 3 7609 with pfc3a and 10720 to compose a dpt ring,. i found L3 mpls vpn work well. but found a problem , after we config more than 300 interface vlan and 100 physical interface, the cpu on 7609 reach 80% after we telnet into 7609 router.
really we can config mpls vpn PE on pfc3a , but someone told me there were some bugs which cisco can't resolve on pfc3a( i don't know). on cisco cco, pfc3a didn't support mpls vpn pe offically.
i think you may ask cisco se for help.

Netflow on Cisco 7600

Hi All.
It is known that SUP720-3B on Cisco 76xx doesn't support ip flow egress on interfaces.
In the last IOS in cisco feature navigator versions I see netflow egress accounting support (see picture bellow).
Somebody tested this feature? It really works?
Thanks.
Konstantin

Hi Prima,
This question has been already answered several times and the answer is still the same :-) : it's not supported on 7600 platform due to hardware limitation.
HTH
Laurent.

Cisco 7600 under attack?

Is possible to router 7600 Sup720-10GE-3CXL , CPU goes up to 99% when under attack ?
I think we have some attack from outside and that destination ip is uplink ip of 7600 router .
Can syn packets rise cpu on 7600? Can they go to RP processor ?
somethink like this attached .

Hi,
This can be a kind of SYN flood attck. You can send this traffic to a loopback or contact your ISP and ask them to block this traffic.
HTH
Luis Silva
"If you need PDI (Planning, Design, Implement) assistance feel free to reach"
http://www.cisco.com/web/partners/tools/pdihd.html

Cisco 7600 in MPLS

Similar Messages

Maybe you are looking for