Cisco 7604 System controller errors
Hello
Can any one help me with the followign errors message:
I have a 7604 with the following IOS
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB5, RELEASE SOFTWARE (fc2)
but for some days now I am receiving the following error:
Dec 13 09:51:37.737 CET: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continues
Dec 13 15:30:17.392 CET: %SYSTEM_CONTROLLER-3-ERROR: Error condition detected: TM_NPP_PARITY_ERROR
Dec 13 15:30:17.392 CET: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continues
Dec 13 21:17:24.225 CET: %SYSTEM_CONTROLLER-3-ERROR: Error condition detected: TM_NPP_PARITY_ERROR
Dec 13 21:17:24.225 CET: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continues
Dec 14 04:42:03.363 CET: %SYSTEM_CONTROLLER-3-ERROR: Error condition detected: TM_NPP_PARITY_ERROR
Dec 14 04:42:03.363 CET: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continues
Dec 14 06:27:10.935 CET: %SYSTEM_CONTROLLER-3-ERROR: Error condition detected: TM_NPP_PARITY_ERROR
Any ideas ?
Regards Suhale
Hello Armando,
I have faced same issue today, i know this post is old but it is useful, i dont know if you can reply me or not .
Would you please answer my question:
have 7606 router, got crashed today and i noticed these logs:
Mar 15 09:58:01 UTC: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continues
Mar 15 09:58:30 UTC: %CPU_MONITOR-2-NOT_RUNNING: CPU_MONITOR messages have not been sent for 30 seconds [*Sched* 1%/1% (00:00:31.228 92%/92%)] [IP SLAs Event Processor 00:13:04.660] [ACCT Periodic Proc 00:01:34.336] [IP SLAs Event Processor 00:06:17.848]
Mar 15 09:58:30 UTC: %CPU_MONITOR-2-NOT_RUNNING_TB: CPU_MONITOR traceback: 428284A8 427C6AB4 4193DA54 4193DC88 41F01354 42AD9CC4 42AE3128 42CC9070
Mar 15 09:59:00 UTC: %CPU_MONITOR-2-NOT_RUNNING: CPU_MONITOR messages have not been sent for 60 seconds [*Sched* 1%/1% (00:01:01.228 96%/96%)] [IP SLAs Event Processor 00:13:34.660] [ACCT Periodic Proc 00:01:34.336] [IP SLAs Event Processor 00:06:17.848]
Mar 15 09:59:00 UTC: %CPU_MONITOR-2-NOT_RUNNING_TB: CPU_MONITOR traceback: 428284A8 427C6AB4 4193DA54 4193DC88 41F01354 42AD9CC4 42AE3128 42CC9070
Mar 15 09:59:30 UTC: %CPU_MONITOR-2-NOT_RUNNING: CPU_MONITOR messages have not been sent for 90 seconds [*Sched* 1%/1% (00:01:31.228 97%/97%)] [IP SLAs Event Processor 00:14:04.660] [ACCT Periodic Proc 00:01:34.336] [IP SLAs Event Processor 00:06:17.848]
Mar 15 09:59:30 UTC: %CPU_MONITOR-2-NOT_RUNNING_TB: CPU_MONITOR traceback: 428284A8 427C6AB4 4193DA54 4193DC88 41F01354 42AD9CC4 42AE3128 42CC9070
Mar 15 10:00:00 UTC: %CPU_MONITOR-2-NOT_RUNNING: CPU_MONITOR messages have not been sent for 120 seconds [*Sched* 1%/1% (00:02:01.228 98%/98%)] [IP SLAs Event Processor 00:14:34.660] [ACCT Periodic Proc 00:01:34.336] [IP SLAs Event Processor 00:06:17.848]
Mar 15 10:00:00 UTC: %CPU_MONITOR-2-NOT_RUNNING_TB: CPU_MONITOR traceback: 428284A8 427C6AB4 4193DA54 4193DC88 41F01354 42AD9CC4 42AE3128 42CC9070
Mar 15 10:00:30 UTC: %CPU_MONITOR-2-NOT_RUNNING: CPU_MONITOR messages have not been sent for 150 seconds [*Sched* 1%/1% (00:02:31.228 98%/98%)] [IP SLAs Event Processor 00:15:04.660] [ACCT Periodic Proc 00:01:34.336] [IP SLAs Event Processor 00:06:17.848]
Mar 15 10:00:30 UTC: %CPU_MONITOR-2-NOT_RUNNING_TB: CPU_MONITOR traceback: 428284AC 427C6AB4 4193DA54 4193DC88 41F01354 42AD9CC4 42AE3128 42CC9070
Mar 15 10:00:33 UTC: %CPU_MONITOR-3-PEER_FAILED: CPU_MONITOR peer process has failed to receive heartbeats, reset by [5/0]
%Software-forced reload
10:00:33 UTC Fri Mar 15 2013: Breakpoint exception, CPU signal 23, PC = 0x4278D310
Would you please share your experience about this issue.
Regards,
Ahmed
Similar Messages
-
Cisco Integrated Management Controller Unexpected Error
I m getting unexpected error from my Cisco Integrated Management Controller when i login.
I cannot see the server properties and Cisco Integrated Management Controller (CIMC) Information.
the fields are blank.
Only the server status can been seen.
All the status are showing Good.
What should I do ?
There is no error on the Fault Summary.The CIMC is an on-board management unit for the Cisco UCS C-series Rack-mount servers that provides out-of-band management capabilities. There is no additional cost to use the CIMC. However, you might consider other management options if you prefer a single management system rather than managing each server via CIMC separately. The Cisco UCS C-Series Management Options Video Data Sheet (http://www.cisco.com/en/US/prod/collateral/ps10265/ps10493/cis-102143.html) has some useful information on the management options for the Cisco UCS C-series Rack-mount servers.
-
HD Controller Error in System Properties
Hello,
Under system properties--hard disk controllers I have 3 entries: Primary IDE Controller (single fifo), Secondary IDE controller (single fifo), and Duel PCI IDE Controller.
The primary and secondary IDE controller entries have exclamation marks next to them noting that they are not working corectly.
My 2 hard disk drives do not show under the disk drive entry due to the controller "errors".
What IDE drivers should I use to fix this problem. Since I cannot access the hard drives I cannot turn on DMA support.
Thanks for the help!Quote
Originally posted by biodude
What IDE drivers should I use? The drivers that the puter wants to use (MS) aren't good. I can't see my hard drives, or CD ROM in Win ME system properties. This means that the drives are using MSDOS compatibility mode.
Does NVIDIA have any NF2 IDE drivers?
Thanks
Can your machine read CDs? There may be drivers for your IDE controllers under Windows ME on the CD that came with your motherboard.
Caveat: I am speaking from experience with EPoX and ASUS motherboards; I am fairly new to MSIs, but I would expect they would have the same sort of drivers available.
--Barry -
Problem !!= Need help about "police cir" in MLS cisco 7604
hi all ,
i have MLS cisco 7604 ,
i tried to use QOS to dedicate cir for specific subnet , but it failed , it seems that bandwidth command dont work on that platform !!!
my 1st question eis can i apply QOS and use bandwidth command ??? is it impossible ????
=============================================================================================
my 2nd question is ,
i have 600 M as total download traffic ,
i want to limit the bw on the interface from 600M to 520 M
i configured the following :
================================================
Gateway7600#
sh ip access-lists drvirus
Extended IP access list drvirus
10 deny ip any x.x.x.0 0.0.0.31 (1802 matches)
20 permit ip any any (2507719 matches)
=================================================
Gateway7600#
sh class-map drvirus
Class Map match-all drvirus (id 4)
Match access-group name drvirus
===================================================
Gateway7600#
sh policy-map drvirus
Policy Map drvirus
Class drvirus
police cir 500000000 bc 93750000 be 187500000
conform-action transmit
exceed-action drop
violate-action drop
====================================================
Gateway7600#
sh running-config interface gigabitEthernet 1/5
Building configuration...
Current configuration : 258 bytes
interface GigabitEthernet1/5
description 7600to7200
mac-address 503d.e5af.9c45
ip address 172.30.40.2 255.255.255.252
ip wccp 70 redirect in
ip wccp 90 redirect in
load-interval 30
service-policy input drvirus
service-policy output rateupload
end
==========================================================================
but when i try to put under the interface level ,
service-policy input drvirus
it fails and give me the error ===>
Gateway7600(config-if)#service-policy input drvirus
burst (bc) must be between 1000 and 31250000 for this interface
Configuration failed on GigabitEthernet1/5
i tried another trial ,
i changed police cir from
police cir 500000000 bc 93750000 be 187500000
to ===>
police cir 500000000 bc 250000 be 1000
after that , it was accepted under the interface command.
but i dont see any limitation in bw !!!!!!!
wish to help me =============?
================================================
i have the following speifications :
Gateway7600#sh module
Mod Ports Card Type Model Serial No.
1 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAD104204GX
Mod MAC addresses Hw Fw Sw Status
1 0018.bad2.2324 to 0018.bad2.232f 4.4 12.2(18r)SX 15.2(4) Ok
Mod Sub-Module Model Serial Hw Status
1 Policy Feature Card 3 WS-F6K-PFC3B SAD104201HK 2.3 Ok
1 Cat6k MSFC 2A daughterboard WS-F6K-MSFC2A SAD104004UC 3.1 Ok
Mod Online Diag Status
1 Pass
===================================================================
Gateway7600#sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(4)S, RELEASE SOFTWARE (fc1)
Technical Support:
http://www.cisco.com/techsupport
Copyright © 1986-2012 by Cisco Systems, Inc.
Compiled Fri 20-Jul-12 18:18 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(4)S, RELEASE SOFTWARE (fc1)
Gateway7600 uptime is 32 weeks, 7 hours, 6 minutes
Uptime for this control processor is 13 weeks, 7 hours, 10 minutes
System returned to ROM by power-on (SP by power-on)
System restarted at 06:26:11 UTC Sat Apr 20 2013
System image file is "sup-bootdisk:c7600s3223-adventerprisek9-mz.152-4.S.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco CISCO7604 (R7000) processor (revision 2.0) with 458752K/65536K bytes of memory.
Processor board ID FOX1509G2DK
R7000 CPU at 300MHz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
1 Virtual Ethernet interface
9 Gigabit Ethernet interfaces
1915K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
===================================================================================any suggestion ??? any help ???
-
System FCS error frames on Catalyst 3750
Please,
may someone explain what are the "System FCS error frames" I see with "show controllers ethernet-controller" on some ports of a Catalyst (on trunk and also on access ports) WS-C3750G-24TS-S (3 switches in stackwyse)?
Error counters advance slowly, but they do grow... and I am afraid this could be the reason for variable slow access time to a server application menu...
For example "8 System FCS error frames".
The ports are connected to a PIX-515E and I see the same error count on the firewall interfaces (PIX "show interface" command shows me "8 input errors, 8 CRC, 0 frame, 0 overrun, 8 ignored, 0 abort")
A few errors may be seen also on other ports, connected to other (C3550)switches.
I tried to upgrade the IOS version, so I loaded "ipbase 12.2(25)SEB4 " on the Catalyst 3750, but it did not solve the problem.
PIX firewalls are running software 6.3(4).
Why these errors are called "System FCS error frames" ? I could not find anything searching on Cisco CCO!
ThanksI apologies for the delay answering, my notebook has been down for 5 days and also cco access password...
Thank you for the explanation and suggestion.
We have a second rack with another three switch 4750 in stackwyse, same models as the "faulty" ones, and the errors are not present on those switches, so it must be something hardware related on the first group of switches.
I cannot touch those devices at the moment, we captured traffic frames with 3 Notebook PCs running "Ethereral" lan sniffer, traffic to and from the server and two clients and we discovered that in different ports of those switches, some packets never reach the clients, causing many TCP retransmissions, especially witch continuous traffic (http get and ftp transfers). This problem is visible on some, but not all, of the catalsyt 3750 switches in stackwyse, but in every one of the three switches. We are planning to go on-site and replace the hopefully faulty one ( or reseat the cables as you suggested).
Is this a problem you have seen before?
Regards
Franco Feri -
Cisco LWAP & WLAN Controller Flexconnect Across HP Switches
Hello All, I'm looking for a little guidance in making the needed routing and switching configuration changes on our Corporate Network to accomadate flex connect functionality for Cisco Lightweight Access Points (LWAPs). The LWAPs that are currently configured on our network only work when our WLAN Controller is up and running and I need for them to be disconnectable so that we can move the WLAN Controller to our virtual co-lo. It should be known that I inhereted this network from the previous admin and have been working hard to map everything out to the best of my ability. Also, the WLAN controller is already operating in our production network so it limits my ability to do much testing.
Just FYI, I'm a new Systems Admin promoted from a Desktop Support role and have my CCENT (Currently working on CCNA & MCITP Server Admin) so I have some knowledge but it is limited on the networking and switching side of things. Unfortunately, the Senior Systems Admin has even less knowledge of networking than me and I don't really have anyone to turn to which is why I'm posting here. I would have utilized GNS to help me simulate the configuration however there are HP switches in the mix and no means of emulating them.
-Relevant Device List-
(CONSA251) Sonicwall NSA 240 - 10.1.1.251
Interface Information
Interface IP Address Description
X0 -> LAN
10.1.1.251 LAN Interface
X1 -> WAN
************* Time Warner WAN
X2 -> DMZ
************* DMZ Interface
X3 -> WAN
************* Sprint WAN
X0-V20 -> LAN
10.1.101.1 Corporate WLAN
X0-V30 -> LAN
192.168.1.1 Guest WLAN
(CORT250) Cisco 3845 - 10.1.1.250
(CO-WLAN-CTRLER) Cisco 5508 Wireless Controller - 10.1.1.2
(COSW240) HP Procurve 4108GL - 10.1.1.240
(COSW238) HP Procurve 2510B-24 - 10.1.20.238
(CORP-AP-MIS) AIR-LAP1131AG-A-K9 - 10.1.1.79
(COSW239) HP1810G-24 - No IP (Inaccesible but being replaced)
I will now go on to explain our network topology as it pertains to the WAPs and WLAN Controller and how I believe it needs to be configured in order to operate from my perspective.
Our Corporate and Guest Wireless Access is provided via the Sonicwall CONSA251 through a connection from the X0 interface to HP Switch COSW239 which is then connected to WLAN Controller CO-WLAN-CTRLER as detailed below:
Device - Interface Name/Port
CONSA251 - X0
COSW239 - 2
COSW239 - 18,19
CO-WLAN-CTRLER - 2,3
The WLAN Controller currently communicates with all the LWAPs via Layer 3 TCP\IP as I understand it and then routes all DHCP requests and traffic destine for the 10.1.101.1 (corporate WLAN) and 192.168.1.1 (Guest WLAN) to the Sonicwall and vice versa.
Now what I am trying to do is VLAN the LWAP CORP-AP-MIS across the HP Switches to the X0 interface on the Sonicwall NSA240 where it will be able to route traffic via VLAN 20 & 30. The problem lies in my inexperience with HP VLAN configurations and how the ports need to be configured on each device so it can route traffic to the Sonicwall when the WLAN Controller is shutdown.
The LWAP CORP-AP-MIS layer 2 trace to the WLAN Controller is as shown below:
Device - Interface Name/Port
CORP-AP-MIS - FA/0
COSW238 - 16
COSW238 - 25
COSW240 - B4
COSW240 - H6
CORT250 - GigabitEthernet0/0
CORT250 - Se1/0
CONSA251 - X0
Now for all intesive purposes the Corporate Router CORT250 should probably be handling the routing for our Corporate and Guest Wireless network however that was not the way it was originally setup and I have to work with what was inhereted. The Corporate Router CORT250 has a default route to the Sonicwall and the Sonicwall CONSA251 has all the routing already in place for the Corporate & Guest WLANs.
What I would like to do is VLAN off the X0-V20&V30 accross multiple switches and switchports to each LWAP in our building. I do have the LWAP I'm testing on configured with Flex Connect which I understand is required for it to be disconnectable.
Any guidance on how I would go about configuring this accross devices would be appreciated. I know there are some difference between HP and Cisco Switching terms and how tagging, untagging, and trunking works however I lack the experience to apply this in practice especially in a production environment.
I will be happy to provide any additional information or clarification that is needed. Thank you in advance for the help.Just to add about the ISE... you can profile, but having only one ssid might or might not work in your situation. Also if you end up with remote sites or ap's in h-reap mode, currently ISE cant do any profiling. If you go with the 7500 or 5508/WiSM2, they don't really do an active-active or active backup. They are both up and you can split the load or put all ap's on one, its up to you. I usually split the load just to make sure both are working. I don't want to all of a sudden loose the primary and then find out my secondary/backup is not working.
-
MBP "System Profile" error when try read "Logs" and long time blue screen
MBP "System Profile" error when try to read "Logs" and it takes long time blue screen at startup.
This happened all time when I open the "System Profiler" application and then select the option "Log", then the system crashed again over and over. The system was reinstalled clean but the error occurs again, without any third party application installed.
Here is the error:
Sun Jun 22 20:13:47 2008
panic(cpu 0 caller 0x001A8CD4): Kernel trap at 0x007efc12, type 14=page fault, registers:
CR0: 0x80010033, CR2: 0x00000000, CR3: 0x013ab000, CR4: 0x00000660
EAX: 0x00000000, EBX: 0x045ce1e0, ECX: 0x05782c64, EDX: 0x00010001
CR2: 0x00000000, EBP: 0x344d3ca8, ESI: 0x046ad5c0, EDI: 0x046a8040
EFL: 0x00010206, EIP: 0x007efc12, CS: 0x00000008, DS: 0x00010010
Error code: 0x00000000
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x344d3ab8 : 0x12b0fa (0x459294 0x344d3aec 0x133243 0x0)
0x344d3b08 : 0x1a8cd4 (0x4627fc 0x7efc12 0xe 0x461fac)
0x344d3be8 : 0x19ede5 (0x344d3c00 0x206 0x344d3ca8 0x7efc12)
0x344d3bf8 : 0x7efc12 (0xe 0x48 0x10 0x3e0010)
0x344d3ca8 : 0x3ef261 (0x45ce1e0 0x46a2c40 0x49a7a4 0x0)
0x344d3ce8 : 0x40abe6 (0x46a8040 0x46a2c40 0x344d3d28 0x3eeac0)
0x344d3d08 : 0x40e4fb (0x46aec00 0x46a2c40 0x46aec04 0x46aec00)
0x344d3d28 : 0x43ab14 (0x46aec00 0x46a2c40 0x600000 0x19c8d1)
0x344d3d78 : 0x18801e (0x46aec00 0x4a5e5ac 0x4a5e5c0 0x11d975)
0x344d3db8 : 0x12d17e (0x450adac 0x4a5e590 0x0 0x0)
0x344d3df8 : 0x126257 (0x450ad00 0x0 0x18 0x344d3ee4)
0x344d3f08 : 0x1973dd (0x344d3f44 0x0 0x0 0x0)
0x344d3fc8 : 0x19f3b3 (0x479fee0 0x0 0x10 0x0)
No mapping exists for frame pointer
Backtrace terminated-invalid frame pointer 0xbffff1c8
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOFireWireIP(1.7.1)@0x7ea000->0x7f2fff
dependency: com.apple.iokit.IOFireWireFamily(3.4.4)@0x6ed000
dependency: com.apple.iokit.IONetworkingFamily(1.6.0)@0x5d1000
BSD process name corresponding to current thread: ioreg
Mac OS version:
9D34
Kernel version:
Darwin Kernel Version 9.3.0: Fri May 23 00:49:16 PDT 2008; root:xnu-1228.5.18~1/RELEASE_I386
System model name: MacBookPro3,1 (Mac-F4238BC8)
This is the System Config:
Model: MacBookPro3,1, BootROM MBP31.0070.B07, 2 processors, Intel Core 2 Duo, 2.4 GHz, 2 GB
Graphics: GeForce 8600M GT, GeForce 8600M GT, spdisplayspciedevice, 256 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 667 MHz
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 667 MHz
AirPort: spairportwireless_card_type_airportextreme (0x168C, 0x87), 1.3.5
Bluetooth: Version 2.1.0f17, 2 service, 1 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
PCI Card: pci168c,24, sppci_othernetwork, PCI Slot 5
Serial ATA Device: FUJITSU MHW2160BHPL, 149.05 GB
Parallel ATA Device: HL-DT-ST DVDRW GSA-S10N
USB Device: Built-in iSight, Apple Inc., high_speed, 500 mA
USB Device: Bluetooth USB Host Controller, Apple, Inc., full_speed, 500 mA
USB Device: Apple Internal Keyboard / Trackpad, Apple Computer, full_speed, 500 mA
USB Device: IR Receiver, Apple Computer, Inc., low_speed, 500 mAHello @larrycarol99,
I understand that after upgrading your computer when you plug in an ethernet cord you get a hardware malfunction error. I am providing you with a Microsoft Support document: Hardware Malfunction Results in System Error Message that explains what causes that error and provides steps on fixing it. I am also including a link to the Compaq Presario 5300US Desktop PC Drivers page, which unfortunately does not have any drivers for your computer running Windows Vista.
I hope this helps. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter -
Problem Cisco Catalyst 3850 input errors
Ive installed two stacked Catalyst 3850s. Connected to these two switches I have a SAN 6210 Equallogic Dell ESX .
The interfaces on the switches is bundels with Port-channel. MTU size 9198. On swich one its no problem but on switch two I see input errors on these interface.
If I move the cables from switch two to one then its ok...
I have two 10G going to the SAN. And 4 ESX server with 2 ISCSI each.
interface Port-channel21
description ESX1 ISCSI SAN
switchport access vlan 21
switchport mode access
flowcontrol receive desired
spanning-tree portfast
spanning-tree bpduguard enable
Port-channel21 is up, line protocol is up (connected)
Hardware is EtherChannel, address is
Description: ESX1 ISCSI SAN
MTU 9198 bytes, BW 2000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 17/255, rxload 16/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, link type is auto, media type is
input flow-control is off, output flow-control is unsupported
Members in this channel: Gi1/0/25 Gi1/0/34
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:07:12, output never, output hang never
Last clearing of "show interface" counters 1d21h
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 128760000 bits/sec, 8233 packets/sec
5 minute output rate 137021000 bits/sec, 7343 packets/sec
520088013 packets input, 1454135312 bytes, 0 no buffer
Received 1088 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
1534 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
564793180 packets output, 978716517 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped outHi and Sorry Just copied and past the part that I thought was the problem. It seems that MTU size on switch two in the stack still has MTU 1500......
So here is the lot....
This interface is OK
sh controllers ethernet-controller g1/0/25
Transmit GigabitEthernet1/0/25 Receive
2373084674113 Total bytes 2700589618458 Total bytes
1259517537 Unicast frames 1355829627 Unicast frames
2373055994149 Unicast bytes 2700589410330 Unicast bytes
314726 Multicast frames 0 Multicast frames
25604588 Multicast bytes 0 Multicast bytes
44657 Broadcast frames 3252 Broadcast frames
3075376 Broadcast bytes 208128 Broadcast bytes
0 System FCS error frames 0 IpgViolation frames
0 MacUnderrun frames 0 MacOverrun frames
0 Pause frames 0 Pause frames
0 Cos 0 Pause frames 0 Cos 0 Pause frames
0 Cos 1 Pause frames 0 Cos 1 Pause frames
0 Cos 2 Pause frames 0 Cos 2 Pause frames
0 Cos 3 Pause frames 0 Cos 3 Pause frames
0 Cos 4 Pause frames 0 Cos 4 Pause frames
0 Cos 5 Pause frames 0 Cos 5 Pause frames
0 Cos 6 Pause frames 0 Cos 6 Pause frames
0 Cos 7 Pause frames 0 Cos 7 Pause frames
0 Oam frames 0 OamProcessed frames
0 Oam frames 0 OamDropped frames
423237 Minimum size frames 78563 Minimum size frames
593742624 65 to 127 byte frames 338414660 65 to 127 byte frames
1416083 128 to 255 byte frames 4836098 128 to 255 byte frames
558097 256 to 511 byte frames 1505992 256 to 511 byte frames
5464138 512 to 1023 byte frames 6457219 512 to 1023 byte frames
472854085 1024 to 1518 byte frames 834470341 1024 to 1518 byte frames
80781 1519 to 2047 byte frames 257961 1519 to 2047 byte frames
2891352 2048 to 4095 byte frames 13701476 2048 to 4095 byte frames
14353508 4096 to 8191 byte frames 8698824 4096 to 8191 byte frames
168093015 8192 to 16383 byte frames 147411745 8192 to 16383 byte frames
0 16384 to 32767 byte frame 0 16384 to 32767 byte frame
0 > 32768 byte frames 0 > 32768 byte frames
0 Late collision frames 0 SymbolErr frames
0 Excess Defer frames 0 Collision fragments
0 Good (1 coll) frames 0 ValidUnderSize frames
0 Good (>1 coll) frames 0 InvalidOverSize frames
0 Deferred frames 0 ValidOverSize frames
0 Gold frames dropped 0 FcsErr frames
0 Gold frames truncated
0 Gold frames successful
0 1 collision frames
0 2 collision frames
0 3 collision frames
0 4 collision frames
0 5 collision frames
0 6 collision frames
0 7 collision frames
0 8 collision frames
0 9 collision frames
0 10 collision frames
0 11 collision frames
0 12 collision frames
0 13 collision frames
0 14 collision frames
0 15 collision frames
0 Excess collision frames
LAST UPDATE 4870 msecs AGO
This interface have problem. It is in portchannel with g1/0/25. Ive got more interfaces and port-channels showing the same behavior for switch two in my cluster.
sh controllers ethernet-controller g2/0/25
Transmit GigabitEthernet2/0/25 Receive
925460044357 Total bytes 201085804055 Total bytes
702370104 Unicast frames 184041790 Unicast frames
925449913241 Unicast bytes 201085599895 Unicast bytes
118823 Multicast frames 0 Multicast frames
9171804 Multicast bytes 0 Multicast bytes
14251 Broadcast frames 3190 Broadcast frames
959312 Broadcast bytes 204160 Broadcast bytes
0 System FCS error frames 0 IpgViolation frames
0 MacUnderrun frames 0 MacOverrun frames
0 Pause frames 0 Pause frames
0 Cos 0 Pause frames 0 Cos 0 Pause frames
0 Cos 1 Pause frames 0 Cos 1 Pause frames
0 Cos 2 Pause frames 0 Cos 2 Pause frames
0 Cos 3 Pause frames 0 Cos 3 Pause frames
0 Cos 4 Pause frames 0 Cos 4 Pause frames
0 Cos 5 Pause frames 0 Cos 5 Pause frames
0 Cos 6 Pause frames 0 Cos 6 Pause frames
0 Cos 7 Pause frames 0 Cos 7 Pause frames
0 Oam frames 0 OamProcessed frames
0 Oam frames 0 OamDropped frames
155980 Minimum size frames 3226 Minimum size frames
92357460 65 to 127 byte frames 52503630 65 to 127 byte frames
542363 128 to 255 byte frames 660137 128 to 255 byte frames
1843346 256 to 511 byte frames 500600 256 to 511 byte frames
6158096 512 to 1023 byte frames 1116353 512 to 1023 byte frames
601445933 1024 to 1518 byte frames 129261034 1024 to 1518 byte frames
0 1519 to 2047 byte frames 319527 1519 to 2047 byte frames
0 2048 to 4095 byte frames 0 2048 to 4095 byte frames
0 4096 to 8191 byte frames 0 4096 to 8191 byte frames
0 8192 to 16383 byte frames 0 8192 to 16383 byte frames
0 16384 to 32767 byte frame 0 16384 to 32767 byte frame
0 > 32768 byte frames 0 > 32768 byte frames
0 Late collision frames 0 SymbolErr frames
0 Excess Defer frames 0 Collision fragments
0 Good (1 coll) frames 0 ValidUnderSize frames
0 Good (>1 coll) frames 319524 InvalidOverSize frames
0 Deferred frames 3 ValidOverSize frames
0 Gold frames dropped 0 FcsErr frames
0 Gold frames truncated
0 Gold frames successful
0 1 collision frames
0 2 collision frames
0 3 collision frames
0 4 collision frames
0 5 collision frames
0 6 collision frames
0 7 collision frames
0 8 collision frames
0 9 collision frames
0 10 collision frames
0 11 collision frames
0 12 collision frames
0 13 collision frames
0 14 collision frames
0 15 collision frames
0 Excess collision frames -
Toshiba Mini NB505-N508
PN : PLL50U-01R00C
Keeps getting an Admin Tools/Event Viewer/ERROR :
The driver detected a controller error on \Device\Harddisk1\DR1
Below is COPY/PASTE of error message :
Log Name: System
Source: Disk
Date: 4/16/2011 10:15:00 AM
Event ID: 11
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: OnTheRoad
Description:
The driver detected a controller error on \Device\Harddisk1\DR1.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Disk" />
<EventID Qualifiers="49156">11</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-04-16T17:15:00.548654300Z" />
<EventRecordID>13270</EventRecordID>
<Channel>System</Channel>
<Computer>OnTheRoad</Computer>
<Security />
</System>
<EventData>
<Data>\Device\Harddisk1\DR1</Data>
<Binary>0E04680001000000000000000B0004C003010000000000000000000000082D00000000000000000089ED020000000000FFFFFFFF060000004000000000000000FF0006120C000010000000003C000000000000000002F78F00000000989CBD87000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</Binary>
</EventData>
</Event>
Attached is screen shot of reoccurrance of error.
I have run complete check disc from C:/ properties with fix option and surface scan, but with no results
What would you suggest as my next steps in deternmining what the problem is ?
thx ... don
Attachments:
discerror.jpg 76 KBmini notebook NB505-N508BL Specifications
mini notebook NB505-N508BL Downloads
Try reloading these critical base drivers in this order. Download these to your desktop and double click on them to install.
Intel Chipset SW Installation Utility
Intel Rapid Storage Technology Driver
Intel Display Driver
Realtek Audio Driver
If this fixes up your problem, it was probably a Windows Update that caused the problem. I recommend setting Windows Update to only allow manual updates, and when you check for updates, never let it change any of your hardware drivers, Toshiba laptops are very finicky about using only their drivers.
Click 'Start - All Programs -Windows Update', then click on 'Change settings' on the menu at left, under 'Important updates' click on the drop down menu at right, select 'Never check for updates (not recommended)', and then click 'OK'.
Please let us know if it works. Good luck.
Mike -
Hi there
I hope you can help.
I have a PC here which is reporting numerous controller errors, some of which culminate in the dreaded BSOD. I have included the information from one of the Event Viewer files below. If anyone can offer any advice please that would be much appreciated.
FYI I have run the Lenovo hard drive quick test and Windows memory diagnostic tools, both of which it passed.
Many thanks.
Phil
System Type: 3000 J110
Model number: 7396-46G
OS: XP Pro SP3
Event Type: Error
Event Source: Disk
Event Category: None
Event ID: 11
Date: 04/11/2009
Time: 13:12:30
User: N/A
Computer:
Description:
The driver detected a controller error on \Device\Harddisk0\D.
Data:
0000: 04 00 68 00 01 00 b6 00 ..h...¶.
0008: 00 00 00 00 0b 00 04 c0 .......À
0010: 01 01 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 7e 00 bc 00 00 00 00 .~.¼....
0028: 66 09 00 00 00 00 00 00 f.......
0030: ff ff ff ff 03 00 00 00 ÿÿÿÿ....
0038: 40 00 00 8f 02 00 00 00 @......
0040: 00 20 0a 12 80 01 20 40 . ... @
0048: 00 00 00 00 0a 00 00 00 ........
0050: 00 00 e6 89 a8 0f d8 89 ..æ¨.Ø
0058: 00 00 00 00 78 0d d8 89 ....x.Ø
0060: 02 00 00 00 3f 00 5e 00 ....?.^.
0068: 2a 08 00 5e 00 3f 00 00 *..^.?..
0070: 08 00 00 00 00 00 00 00 ........
0078: f0 00 04 00 00 00 00 0b ð.......
0080: 00 00 00 00 08 03 00 00 ........
0088: 00 00 00 00 00 00 00 00 .......check for your mothe board...use pc doctor diagnostics which u get with lenovo systems
Cheers and regards,
• » νιנαｿѕαяα∂нι ѕαмανє∂αм ™ « •
●๋•کáŕádhí'ک díáŕý ツ
I am a volunteer here. I don't work for Lenovo -
Satellite L505D Controller Error on IdePort1
I have a Satellite L505D-S5983 that keeps locking up momentarily.
When this happens I get the following in the Systems EventLog (windows 7)
Source: atapi
Event ID: 11
Description: The driver detected a controller error on \Device\Ide\IdePort1.
Anyone know what device is at \Device\Ide\IdePort1 for this model?
Thanks,
Mark> {quote:title=peterk_1 wrote:}{quote}
> Not all drive bays are made equal. The P500 second bay takes the "thicker" 2.5" drives.
>
> The current Intel chipset "driver" is v10. I have it installed BUT the installation if you want to do a complete install is not a simple task. If you download and unpack you can point the driver update to that location. Start at Intel.com
Thanks!! This worked! It seems the Intel INF auto update utility didn't update them to the latest. I had to download the [RST and AHCI Driver and GUI|http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=20110&lang=eng] and manually search for new drivers in device manager. Now the drive is noticeably quicker and error free :)
Thanks for all the help guys :) -
Satellite P300-156 - driver detected controller error on \Device\Ide\IdePort1
Hi
I have recently installed a secondary hard drive in my P300-156 and am having some problems with it. I keep getting Event ID 11 in the system event log "The driver detected a controller error on \Device\Ide\IdePort1." and suffer with very bad performance with this drive.
The drive is new and works fine in other systems and even works ok if I swap drive bays on my P300-156 but the problem with that is the drive does not fit in the other bay as it is quite thick. The drive in question is a Samsung HM100UI 2.5" 1TB Sata. I have also tried other drives in this bay and they work ok too.
I am using windows 7 ultimate and Intel chipset drivers. It's an Intel ICH8M SATA AHCI controller, driver version 7.0.0.1013. Have tried different drivers and AHCI/IDE mode. Also tried a fresh installation and the problem persists.
Am at a loss why this drive is having problems is there anything else someone can suggest to try?
Thanks in advance.> {quote:title=peterk_1 wrote:}{quote}
> Not all drive bays are made equal. The P500 second bay takes the "thicker" 2.5" drives.
>
> The current Intel chipset "driver" is v10. I have it installed BUT the installation if you want to do a complete install is not a simple task. If you download and unpack you can point the driver update to that location. Start at Intel.com
Thanks!! This worked! It seems the Intel INF auto update utility didn't update them to the latest. I had to download the [RST and AHCI Driver and GUI|http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=20110&lang=eng] and manually search for new drivers in device manager. Now the drive is noticeably quicker and error free :)
Thanks for all the help guys :) -
Controller error on \Device\Harddisk1\DR1
I have been getting the following error repeatedly. My L765D-S7015 (purchased new 12/24/2010) unit has really slowed down and I have tried doing a recovery to no avail. The OS is Winodws 7 Home premium 64-bit. Any suggestions what I should be looking for, or should I take it in for service?
Log Name: System
Source: Disk
Date: 3/27/2011 10:21:22 AM
Event ID: 11
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: toshiba
Description:
The driver detected a controller error on \Device\Harddisk1\DR1.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Disk" />
<EventID Qualifiers="49156">11</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-03-27T17:21:22.309220600Z" />
<EventRecordID>5726</EventRecordID>
<Channel>System</Channel>
<Computer>toshiba</Computer>
<Security />
</System>
<EventData>
<Data>\Device\Harddisk1\DR1</Data>
<Binary>0E01800001000000000000000B0004C003010000000000000000000000082D000000000000000000F7E8020000000000FFFFFFFF0600000058000000000000000000061208000010000000003C000000000000000000000080CD080680FAFFFF00000000000000002067030780FAFFFF0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</Binary>
</EventData>
</Event>
Solved!
Go to Solution.L765D-S7015
Maybe this one?
Satellite L675D-S7015
Source: Disk
Event ID: 11
The driver detected a controller error on \Device\Harddisk1\DR1
Suspect trouble with the controller for the second disk shown in Disk Management (diskmgmt.msc). (The first one is DR0.)
I have tried doing a recovery to no avail.
That pretty much tells us that software is not the problem.
-Jerry -
How can i ensure that the harddisk3 designation is relatd with USB etxernal disk?
I have several erros in LOGs:
An error was detected on device \Device\Harddisk3\DR3 during a paging operation.
and
The driver detected a controller error on \Device\Harddisk3\DR7
All times are HardDisk3 and sometimes it references to DR3 and sometimes DR7
My disk structure is:
2 RAID5 arrays fomr the same disks (80GB and 2 TB)
and USB 2 TB External hard disk with several partitions
I´m 99% sure that the error is related to the external USB disk and the Dell DIag tool shows no problems with any component
DISKPART> list disk
Disk ### Status Size Free Dyn Gpt
Disk 0 Online 80 GB 0 B
Disk 1 Online 2711 GB 0 B *
Disk 2 Online 1862 GB 1024 KB
DISKPART> sele disk 0
Disk 0 is now the selected disk.
DISKPART> detail disk
DELL PERC H700 SCSI Disk Device
Disk ID: 6EFE3928
Type : RAID
Status : Online
Path : 1
Target : 0
LUN ID : 0
Location Path : PCIROOT(0)#PCI(0400)#PCI(0000)#RAID(P01T00L00)
Current Read-only State : No
Read-only : No
Boot Disk : Yes
Pagefile Disk : Yes
Hibernation File Disk : No
Crashdump Disk : Yes
Clustered Disk : No
Volume ### Ltr Label Fs Type Size Status Info
Volume 3 System Rese NTFS Partition 100 MB Healthy System
Volume 4 C DISCO NTFS Partition 79 GB Healthy Boot
DISKPART> sele disk 1
Disk 1 is now the selected disk.
DISKPART> detail disk
DELL PERC H700 SCSI Disk Device
Disk ID: {A42559A8-43EF-4570-B4CF-336A22A718BF}
Type : RAID
Status : Online
Path : 1
Target : 1
LUN ID : 0
Location Path : PCIROOT(0)#PCI(0400)#PCI(0000)#RAID(P01T01L00)
Current Read-only State : No
Read-only : No
Boot Disk : No
Pagefile Disk : No
Hibernation File Disk : No
Crashdump Disk : No
Clustered Disk : No
Volume ### Ltr Label Fs Type Size Status Info
Volume 5 DADOS NTFS Partition 2711 GB Healthy
C:\DADOS\
DISKPART> sele disk 2
Disk 2 is now the selected disk.
DISKPART> detail disk
HP External HDD USB Device
Disk ID: 000904F0
Type : USB
Status : Online
Path : 0
Target : 0
LUN ID : 0
Location Path : UNAVAILABLE
Current Read-only State : No
Read-only : No
Boot Disk : No
Pagefile Disk : No
Hibernation File Disk : No
Crashdump Disk : No
Clustered Disk : No
Volume ### Ltr Label Fs Type Size Status Info
Volume 6 SOFTWARE NTFS Partition 300 GB Healthy
C:\DADOS\DISCO-EXTRA\
Volume 7 TEMPORARIO- NTFS Partition 148 GB Healthy
C:\DADOS\NEW_TRANSF\TEMPORARIO\
Volume 8 TRANSF_LIXO NTFS Partition 149 GB Healthy
C:\DADOS\NEW_TRANSF\TRANSF_LIXO\
Volume 9 R RESTORE NTFS Partition 1264 GB HealthyHi,
For finding the exact hard disk you could refer to this article. It is an old article but the structure is not changed:
How to Distinguish a Physical Disk Device from an Event Message
http://support.microsoft.com/kb/159865
Meanwhile for the error message "error was detected on device \Device\Harddisk3\DR3 during a paging operation", according to my search result it could be related to fragments. So please try a defragment on your hard disk (if it is the USB disk then perform
a defragment on USB disk) and see the result.
If you have any feedback on our support, please send to [email protected] -
The driver detected a controller error on \Device\Harddisk1-4\DR1-4.
Hello all
I just recently bought a new gaming PC on black friday and is running just fine. Then one day i decided to take a look in the event log and i notice an error that would appear four time during startup of the machine.
The driver detected a controller error on \Device\Harddisk1\DR1.
The driver detected a controller error on \Device\Harddisk2\DR2.
The driver detected a controller error on \Device\Harddisk3\DR3.
The driver detected a controller error on \Device\Harddisk4\DR4.
I only have one internal hard drive located on disk 0 and an external located on disk 5. So i have no idea why i'm getting this error when nothing is connected.
I installed the latest controller drivers and just for fun everything else related to my GIGABYTE motherboard but unfortunately still occurs after turning my computer. (note for the bios i have version F4 not sure if updating it to F5 is worth doing for
this issue).
If anyone could help me with this error or if i can just ignore it.
Thank youAngel
If the drive is an SSD update the firmware.
Are the message an error (red symbol) or a warning (yellow symbol)?
I would also run CHKDSK and get the diagnostic utility (and run it of course) from the HD mfr.
CHKDSK /R /F
Chkdsk disclaimer: While performing chkdsk on the hard drive if any bad sectors are found any data available on that sector might be lost so as usual backup your data.
Run CHKDSK /R /F from an elevated (Run as administrator) Command Prompt.
Do this for each hard drive on your system.
When it tells you it can't do it right now - and asks you if you'd like to do it at the next reboot - answer Y (for Yes) and press Enter.
Then reboot and let the test run.
It may take a while for it to run, but keep an occasional eye on it to see if it generates any errors.
http://www.howtogeek.com/howto/windows-vista/guide-to-using-check-disk-in-windows-vista/
See "CHKDSK LogFile" below in order to check the results of the test.
CHKDSK LogFile:
Go to Start and type in "eventvwr.msc" (without the quotes) and press Enter
Expand the Windows logs heading, then select the Application log file entry.
Double click on the Source column header.
Scroll down the list until you find the Chkdsk entry (wininit for Win7) (winlogon for XP).
Copy/paste the results into your next post.
Wanikiya and Dyami--Team Zigzag
Maybe you are looking for
-
How do I connect the new mac Air 13 inch to TV - Data projectors etc.
Hi I feel a little nieve, but I just purchaesed a new macbook air 13 (with the thunderbolt cable) and I can not find any adaptors on the mac store or the internet to get it plug into VGA, DVI, or TV HDMI etc. The older models had a mini port, but th
-
Execute in PL-SQL a configuartion function
Hi, i would like execute a function PL-SQL in other PL-SQL block but the name of function to execute there isn't in the code but in the a table. The first procedure PL-SQL read in the table the name of function to execute. The EXECUTE IMMEDIATE is ve
-
Hello! I just registerd here from my iMac computer running on? Nope, its not running on any OS, im writing from the recorvery menu ;( I erased my whole disk, and i lost my install disc that came with my 27'' iMac... I dont know what to do, i do not h
-
Adobe Acrobat 9 install for Mac
How do I re-install Adobe 9 on my Mac? when I go to download it says not available for mac - it is however available for pc. How can I get my Acrobat 9 back?
-
Lenovo B50-30 AIO touch screen stop working
I bought my Lenovo B50-30 AIO touch screen last year and approximately after 3- 4 months of use the touch screen capability has stopped working.. Contacted customer service but they are unable to help and they told us thay they will send someone to f