Cisco 7606-s with SIP400

Hi!
I Want to buy SIP 400 card, but i don't understand, how much PPPOE sessions I can aggregate with 1 SPA 2x1GE or with 2 SPA 2x1GE or with 4 SPA 2x1GE ?
How many memory it is necessary for SIP-400 Line Card?
Thanks

Hi Winm,
http://tools.cisco.com/ITDIT/MIBS/MainServlet?IMAGE_NAME=c7600rsp72043-ipservicesk9-mz.122-33.SRE2.bin
...show you which OIDs are supported by your software version.
Try the following:
CPU under:
OLD-CISCO-CPU-MID
eg: 1.3.6.1.4.1.9.2.1.58
Memory under :
CISCO-MEMORY-POOL-MIB
eg: 1.3.6.1.4.1.9.9.48
Temperature:
CISCO-ENVMON-MIB
eg: 1.3.6.1.4.1.9.9.13.1.3.1.3
cheers,
Seb.

Similar Messages

CWLMS 3.1 : CiscoView of Cisco 7606-S Router

Hi Friend,
I am facing some issue with CiscoView of 7606-S router.
Please find the attachment for more details.
In figure, The RED Marked LAN port appears GREEN when viewed through CiscoWorks but physically on Cisco 7606-S router, no such port exists at all.
Also besides this, we have 3 fiber ports and 2 RJ-45 port on Cisco router visible through CiscoView, but physically on Cisco router 2 Fiber and 2 RJ-45 port are present.
first fiber port is up and connected whereas when seen through CiscoWorks, it shows 3rd fiber port as green.

you can not display your 7600 in ciscoview, the most probably reason is that a device package is needed to do this. do the following:
1. Download the device package from the link (Cat6000IOS.cv50.v29-1.zip, Cat6000IOS.cv50.v29-1.readme)
http://www.cisco.com/cgi-bin/apps/vwplan/cvresult.cgi?product_class=Routers&product=Internet+Router+7600+IOS&application=All+Versions
2. Go to Common Services > Software Center > Device Update, then select CiscoView > click on 'Check for updates' > select 'Enter Server Path' and enter the path where you downloaded the files > continue the instructions to
install it.
This will probably need to restart ciscoworks to apply the changes.

Anti spoof acl and cisco 7606

Hi all,
I have strange problem with anti spoof access-list which I would like to set up in cisco 7606 with 7600-PFC3CXL. So I made an access-list which is in [1.] and set up on interface Te1/1 like this [2.], but there are no match in output direction? Why? Well I made a test with [3.] but no matchs in access-list and ICMP was working than I made change [4.] and yeap icmp was not working and I have seen match in input direction good. It looks like that output direction in acl not working so I removed line 1 inc acl [4.] and icmp still not working and acl [3.] started matching icmp in line 1? Why? Can anybody help me? Thanks.
Karel
btw.> I tried solve this problem with this links:
http://www.cisco.com/en/US/docs/routers/7600/ios/12.2SR/configuration/guide/acl.html
http://www.cisco.com/web/about/security/intelligence/acl-logging.html
[1.]
Extended IP access list anti_spoof_Te1/1_input
10 deny ip 10.0.0.0 0.255.255.255 any
20 deny ip 172.16.0.0 0.15.255.255 any
30 deny ip 192.168.0.0 0.0.255.255 any
40 deny ip 127.0.0.0 0.255.255.255 any
50 deny ip 194.79.52.0 0.0.3.255 any
60 deny ip 0.0.0.0 0.255.255.255 any
70 permit ip any OUR CIDR
80 permit ip any host BGP Neighbor
90 deny ip any any
Extended IP access list anti_spoof_Te1/1_output
10 deny ip any 10.0.0.0 0.255.255.255
20 deny ip any 172.16.0.0 0.15.255.255
30 deny ip any 192.168.0.0 0.0.255.255
40 deny ip any 127.0.0.0 0.255.255.255
50 deny ip any 0.0.0.0 0.255.255.255
60 deny ip any OUR CIDR
70 permit ip host BGP Neighbor any
80 permit ip OUR CIDR any
90 deny ip any any
[2.]
ip access-group anti_spoof_Te1/1_input in
ip access-group anti_spoof_Te1/1_output out
[3.]
Extended IP access list anti_spoof_Te1/1_output
1 deny icmp host from OUR CIDR host in INTERNET log-input
10 deny ip any 10.0.0.0 0.255.255.255
20 deny ip any 172.16.0.0 0.15.255.255
30 deny ip any 192.168.0.0 0.0.255.255
40 deny ip any 127.0.0.0 0.255.255.255
50 deny ip any 0.0.0.0 0.255.255.255
60 deny ip any OUR CIDR
70 permit ip host BGP Neighbor any
80 permit ip OUR CIDR any
90 deny ip any any log-input
[4.]
Extended IP access list anti_spoof_Te1/1_input
1 deny icmp host from INTERNET host from OUR CIDR
10 deny ip 10.0.0.0 0.255.255.255 any
20 deny ip 172.16.0.0 0.15.255.255 any
30 deny ip 192.168.0.0 0.0.255.255 any
40 deny ip 127.0.0.0 0.255.255.255 any
50 deny ip 194.79.52.0 0.0.3.255 any
60 deny ip 0.0.0.0 0.255.255.255 any
70 permit ip any OUR CIDR
80 permit ip any host BGP Neighbor
90 deny ip any any

Following links may help you
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_white_paper09186a00801a1a55.shtml
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080120f48.shtml

Cisco 7606 FIB Protocol Allocation mismatch after mls cef maximum-routes command

Hi,
we are trying to fine tune the mls cef maximum-routes without success for ipv4 on our Cisco 7606 router equiped like this:
Mod Ports Card Type Model Serial No.
2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL09169CP0
6 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAL10370YH7
Mod MAC addresses Hw Fw Sw Status
2 0013.c38b.ed9c to 0013.c38b.edb3 2.2 12.2(14r)S5 12.2(33)SRC1 Ok
6 0017.9441.b750 to 0017.9441.b753 5.2 8.4(2) 12.2(33)SRC1 Ok
Mod Sub-Module Model Serial Hw Status
2 Centralized Forwarding Card WS-F6700-CFC SAL09159C8T 2.0 Ok
6 Policy Feature Card 3 WS-F6K-PFC3BXL SAL10360CJ0 1.8 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL10360GNX 2.5 Ok
the show version is like this:
System image file is "bootdisk:c7600s72033-adventerprisek9-mz.122-33.SRC1.bin"
We tryied to set the value of the ipv4 FIB TCAM to 720k with this command:
mls cef maximum-routes ip 720
and then to save the configuration we used the "write" command. This was the output after we wrote the configuration:
FIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
User configured :-
IPv4 - 720k
MPLS - 16k (default)
IPv6 + IP Multicast - 144k (default)
Upon reboot :-
IPv4 - 720k
MPLS - 16k (default)
IPv6 + IP Multicast - 144k (default)
so we reloaded the router to get the new value.
when the router was up again it start to reload each 4 minutes. The FIB TCAM value was:
show mls cef maximum-routes
Reload scheduled for 13:50:09 DST Wed Aug 13 2014 (in 2 minutes and 51 seconds)
Reload reason: FIB Protocol Allocation mismatchFIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
User configured :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
Upon reboot :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
We know that our cisco is able to handle up to 1M of ipv4 routes inside the TCAM but we cannot set more than 512k ipv4 routes.
Why the router doesn't accept the new value?
Thanks
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/117712-problemsolution-cat6500-00.html
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/116132-problem-catalyst6500-00.html
https://supportforums.cisco.com/discussion/12250356/recommended-value-7600-ipv4-fib-tcam

Hi Paolo,
#sho ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI13, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 11-Mar-14 04:53 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
punk.gs2 uptime is 17 hours, 55 minutes
Uptime for this control processor is 17 hours, 55 minutes
Time since punk.gs2 switched to active is 17 hours, 54 minutes
System returned to ROM by reload at 22:32:30 BST Mon Sep 1 2014 (SP by reload)
System restarted at 22:35:24 BST Mon Sep 1 2014
System image file is "disk0:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C6504-E (R7000) processor (revision 2.0) with 983008K/65536K bytes of memory.
Processor board ID FOX11270F1B
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from power-on
11 Virtual Ethernet interfaces
50 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
#remote command switch show version
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI13, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 11-Mar-14 05:09 by prod_rel_team
ROM: System Bootstrap, Version 8.5(4)
punk.gs2 uptime is 17 hours, 55 minutes
Time since punk.gs2 switched to active is 17 hours, 55 minutes
System returned to ROM by reload at 22:32:30 BST Mon Sep 1 2014
System restarted at 22:34:17 BST Mon Sep 1 2014
System image file is "disk0:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin"
Last reload reason: Reload Command
cisco Catalyst 6000 (R7000) processor with 983008K/65536K bytes of memory.
Processor board ID FOX11270F1B
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
50 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
500472K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Hope that helps.

Cisco 7606 and out of band remote management

Hi
I have been trying to look for a document to confirm that Cisco 7606 support out of band remote management via Aux port. Can anyone please confirm whether 7606 support out of band remote management.
Regards

The 7606 with a sup will only have a console port and no aux port.
Yes the console port supports OOB management using an external modem.
Thanks, Mak

ASA , Cisco VPN client with RADIUS authentication

Hi,
I have configured ASA for Cisco VPN client with RADIUS authentication using Windows 2003 IAS.
All seems to be working I get connected and authenticated. However even I use user name and password from Active Directory when connecting with Cisco VPN client I still have to provide these credentials once again when accessing domain resources.
Should it work like this? Would it be possible to configure ASA/IAS/VPN client in such a way so I enter user name/password just once when connecting and getting access to domain resources straight away?
Thank you.
Kind regards,
Alex

Hi Alex,
It is working as it should.
You can enable the vpn client to start vpn before logon. That way you login to vpn and then logon to the domain. However, you are still entering credentials twice ( vpn and domain) but you have access to domain resources and profiles.
thanks
John

Cisco ISE FlexAuth with 802.1X PCs and IP Phones as MAB multi-domain Q?

Cisco ISE FlexAuth with 802.1X PCs and IP Phones as MAB multi-domain Q?
Im trying to follow the trustsec 2.1 guide on IP Phones into LowImpact mode.
I can get a PC on its own to authenticate via dot1x/tls
I can get a Cisco IP Phone on its own to authenticate via MAB.
When the two are on the same switchport, the phone will authenticate but not the PC. ISE logs EAP timeouts.
The switchport has the LowImpact port ACL of
ip access-group ACL-DEFAULT in
The IP Phone gets a dACL that allows it ok.
I assume MAB phone and dot1x PC is supported? Any ideas?
Thanks in advance.

The ISE log detailed steps are as follows:
Steps
11001 Received RADIUS Access-Request
11017 RADIUS created a new session
Evaluating Service Selection Policy
15048 Queried PIP
15048 Queried PIP
15004 Matched rule
11507 Extracted EAP-Response/Identity
12300 Prepared EAP-Request proposing PEAP with challenge
12625 Valid EAP-Key-Name attribute received
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12501 Extracted EAP-Response/NAK requesting to use EAP-TLS instead
12500 Prepared EAP-Request proposing EAP-TLS with challenge
12625 Valid EAP-Key-Name attribute received
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12502 Extracted EAP-Response containing EAP-TLS challenge-response and accepting EAP-TLS as negotiated
12800 Extracted first TLS record; TLS handshake started
12805 Extracted TLS ClientHello message
12806 Prepared TLS ServerHello message
12807 Prepared TLS Certificate message
12809 Prepared TLS CertificateRequest message
12505 Prepared EAP-Request with another EAP-TLS challenge
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12504 Extracted EAP-Response containing EAP-TLS challenge-response
12505 Prepared EAP-Request with another EAP-TLS challenge
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12504 Extracted EAP-Response containing EAP-TLS challenge-response
12505 Prepared EAP-Request with another EAP-TLS challenge
11006 Returned RADIUS Access-Challenge
5411 No response received during 120 seconds on last EAP message sent to the client

Integration of CISCO PRIME1.3 with WLC 7.5.102.0

HI
We have newly depolyed CISCO PRIME1.3 in our network Earlier we were using WCS withj WLC 7.0.116.0 .BUt we can not upgrade the WLC to higher version because of compatibity matrix with WCS therefore purchased CISCO PRIME1.3.
Now e we want to upgrade our WLC to 7.5.102.0 but as per cisco complatibity matrix with PRIME it is not supported with PRIME1.3.
Can we go for the upgarde when we have PRIEM1.3.PRIEM is installed on VM.
1.3.0.20
7.4.110.0
7.4.100.60
7.4.100.0
7.3.112.0
7.3.101.0
7.2.111.3
7.2.110.0
7.2.103.0
7.0.240.0
7.0.235.3
7.0.235.0
7.0.230.0
7.1.91.0
7.0.220.0
7.0.116.0
7.0.98.218
7.0.98.0
7.4.110.0
7.4.100.0
7.3.101.0
7.2.110.0
7.2.103.0
7.0.240.0
7.0.230.0
7.0.220.0
7.0.201.204
7.0.112.0
7.0.105.0
ISE 1.0
ISE 1.1
3.2.0SE
IOS12.2(50)SE
IOS12.2(50)SG
IOS12.2(33)SXI
If deploying Prime Infrastructure as a virtual appliance on a customer-supplied server, one of the following versions of VMware ESX or ESXi can be used:
•VMware ESX or VMware ESXi Version 4.0
•VMware ESX or VMware ESXi Version 4.1
•VMware ESXi Version 5.0
Note VMware Tools Version 4.1 is preinstalled in the Prime Infrastructure virtual appliance.

Please upgrade your PI to Pi 1.4 if you want to use WLC 7.5
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.4/release/notes/cpi_rn_14.html

Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users

Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
I've been given a fantastic "opportunity" by my boss to use our existing wireless infrastructure to provide internet access to potentially upto 2000 VIP guests arriving with BYOD devices, in a very densely populated area for a 3 day event. We are talking an area of approx 200m x 15m. Think of it as an awards ceremony/concert. The solution will also be mobile so we will be using internet breakout from different telcos as it will move to approx 20 countries. The area is also incredibly densely populated with other wifi APs. I did a brief site survey and AirMagnet could detect over 2500 other 'rogue' APs from where I was stood! I hope CleanAir works!
We need a simple authentication method for them to connect with zero admin from our side. We don't want to just offer up a rolling daily PSK as that's a bit amateur and we don't really want the VIP guests sharing the PSK with others during their stay. Ideally they could self-provision by providing an email address.
I know the WLC can handle webauth for local users but I don't think it scales very well. ie I don't think I can offer the account to several hundred people.
Cisco ISE looks a very expansive (and expensive) product but I don't think we need all it's capabilities (do I?). It would be nice to just ask a potential user for their email address and grant them access and email them next year. I've seen Cisco NAC but that looks over the top too for just guest users who will only be accessing a shared internet connection.
I've seen 3rd party supposed software solutions from Kiosk Antamedia etc do they work with Cisco Enterprise WLC solutions?
We'd like to limit users to a certain (low) bandwidth and block (say) torrent traffic to keep the general user experience worthwhile.
Does anybody have any case study documents or experience of such a project? As well as the authentication it's how well the APs will handle the dense potential number of clients trying to connect in such a confined space.
Any suggestions would be gratefully appreciated from the knowledgeable community.
Cheers,
Mike

Hi Rasika,
We are having WLC 5508 model with software version running 7.4.121.0. AP Models are AIR-CAP2602I.
Normally our WAN links are good even while the issue pertains. We are connected to remote offices over ipsec site to site vpn for WAN. The link latency in WLC between the AP and the controller shows <1ms.
currently the Guest network is using WPA2-PSK auth given in the controller. we are trying to find a option to make the Guest wireless auth local to the office, and see if this solves the problem.
any suggestions,
Thank you,
Arjun

Monitoring Cisco ASR 1002 with IOS-XE in IPM 4.2

We are running LMS 3.2 with IPM 4.2 installed....and we are looking to do IPSLA monitoring on a couple of our Cisco ASR's with IOS-XE code installed.
I looked at the IPSLA feature mapping and it only talks about supported IOS code....do we need to upgrade our current IPM module to a current version?

Hi Konstantin,
Regarding "It is strange that these commands cleaned from sh run view.": this is normal for many default configuration commands.
Mine is a lab device so I cannot really comment on stability or provide you a recommendation based on that. However, I see that the download section from Cisco.com mentiones the following release as the recommended based on quality, stability and longevity:
asr1002x-universal.03.07.04a.S.152-4.S4a.SPA.bin
The best would be for you to check this with yor cisco Account Team or Advanced Services Team as normally they are the proper point of contacts for SW advisory.
Regards.

Cisco 2600 router with 4A/S module can be terminal server

I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports? Thanks a lot

The commands mean that R1's console is connected using the first RJ-45 cable and is available on port 2001, R2's console is connected using the second RJ-45 cable and is available on port 2002 and so on. Remember that the ports are numbered as 2000 plus the line number. Hence, the first port is 2001. If you have more than eight devices and have connected a second CAB-OCTAL-ASYNC cable then you need to add a similar configuration line with the port numbers starting from 2009 till 2016.
In your configuration u configured 9 ports. So please add second cable for another 8 ports.
To connect to the console of a device, telnet to the terminal server router's loopback address and specify the port number associated to the device. For example, to connect to console of router R1 (from our example) type telnet 192.168.12.1 2001 in the Run dialog box from your PC.
For further information click the below url
http://www.cisco.com/public/technotes/smbsa/en/us/internet/config_cisco_router_term_server.html#trouble

When is the update for Cisco Connect software with OS X 10.8 Mountain Lion?

@OfficialLinksys When will @Cisco_Support update Cisco Connect software with OS X 10.8 Mountain Lion compatibility?

I believe all Mac users are waiting for that update but so far it is not yet available. We are yet to hear from Cisco for its official release for the software that is compatible already for Mountain Lion.

Urgent-- could cisco uc320 work with dumb switch ? how to configure

could cisco uc320 work with dumb poe switch, with its voice vlan alway in 100, I can't change it, and my phone can not find the pbx through the switch, if it can, how can I configure it.

Hi Rex,
If the switch is unmanaged the 802.1q (tagged) ethernet frames typically pass right through the switch as if the phone was directly connected to the UC320W. In this case both voice VLAN works and data VLAN. I would guess that if a switch has PoE that it is a managed switch though. If it is a managed switch you will need to configure ports, vlans, and possibly CDP passthrough.
Chris

CIsco UCS-C200M2 with Unified Communication Products

Hi,
If anybody knows what are the Unified Communication products we can install on Cisco UCS solution with EXS VMware ESXi 4.0 Standard Edition.
If any other products pls let me know that alo.
Thanks in Advance.
Regards,
Sunish

Yes, the DocWiki covers this on the Supported Applications page. It is worth mentioning that only there are specific hardware component requirements of the C200M2 for VTG support.
Please rate useful responses.

Cisco Terminal Server with Meditech lab analyzers

We are having trouble configuring a Cisco 2610XM router (with an NM-16A) for use with various Lab blood gas analyzers that send data via rs-232 to our Meditech C/S health information system. We were hoping to replace our existing Annex and 3Com term servers with the more familiar Cisco term servers but we cannot get it to work quite right.
We do have the Lab analyzer sending date to Meditech, but in the data stream there is a null character (ASCII 0) following the CR character (ASCII 13) when we are expecting ONLY the CR.
Any ideas on what we can do to fix this?
Thanks, in advance.
John

We are using port 2035.
Here is the exsiting line config and show line status:
=======================
line 35
location SRGEM1
no activation-character
special-character-bits 8
transport preferred telnet
transport input pad telnet rlogin
transport output pad telnet rlogin
telnet refuse-negotiations
stopbits 1
tserv001#show line 35
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
35 TTY 9600/9600 - - - - - 58 1 0/0 -
Ready
Line 35, Location: "SRGEM1", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits
Status: Ready
Capabilities: Refuse Telnet Echo, Refuse Suppress-GA
Modem state: Ready
Modem hardware state: noCTS* noDSR* DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none any
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
00:10:00 never none not set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: never
Editing is enabled.
History is enabled, history size is 20.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are pad telnet rlogin.
Allowed output transports are pad telnet rlogin.
Preferred transport is telnet.
No output characters are padded
No special data dispatching characters
=====================
What are the behavioral differences between 2xxx, 4xxx and 6xxx ports?
Thanks for your help.

Cisco 7606-s with SIP400

Similar Messages

Maybe you are looking for