Cisco 7606 stacked VLAN support
Hi All,
Does Cisco 7606 GigabitEthernet modules support stacked VLAN (two VLAN tags)?
If yes, how do I configure it?
Thanks in advance.
Regards,
Sarah
Hi Sean,
Yes, it is QinQ tunneling. I am using Cat6k-Sup720.
Cisco7606(config-vlan)#?
VLAN configuration commands:
are Maximum number of All Route Explorer hops for this VLAN (or
zero if none specified)
backupcrf Backup CRF mode of the VLAN
bridge Bridging characteristics of the VLAN
exit Apply changes, bump revision number, and exit mode
media Media type of the VLAN
mtu VLAN Maximum Transmission Unit
name Ascii name of the VLAN
no Negate a command or set its defaults
parent ID number of the Parent VLAN of FDDI or Token Ring type VLANs
private-vlan Configure a private VLAN
remote-span Configure as Remote SPAN VLAN
ring Ring number of FDDI or Token Ring type VLANs
said IEEE 802.10 SAID
shutdown Shutdown VLAN switching
state Operational state of the VLAN
ste Maximum number of Spanning Tree Explorer hops for this VLAN (or
zero if none specified)
stp Spanning tree characteristics of the VLAN
tb-vlan1 ID number of the first translational VLAN for this VLAN (or
zero if none)
tb-vlan2 ID number of the second translational VLAN for this VLAN (or
zero if none)
Regards,
Sarah
Similar Messages
-
Stacked VLAN (802.1Q-in-Q)
Hi,
I would like to know if the Catalyst 6500 (Sup720-3b) supports the fonctionnality Stacked VLANs (802.1Q-in-Q)
And if Yes, in witch IOS version.
Thanks for your helpYes it does. As early as 12.1 supports this feature.
Hope this helps. Please rate helpful posts. -
I recently bought an 851 only to find out afterwards that it only supports 1 VLAN when I needed it to support at least 7. The documentation on VLAN support seemed pretty buried.
Does anyone know if there is an easy way to find out how many VLANs each router model supports? I dont' want to make the same mistake again, and I can't seem to find what I'm looking for by combing through the data sheets for each model.
Thanks!
Sorry, I meant to post this in the routing and switching forum and I can't figure out how to delete the thread.Hi
A maximum of four VLANs are supported on the Cisco 870 Series with the plus feature set (Advanced IP Services/Advanced Enterprise Services) Cisco IOS. The Cisco 850 Series only supports one 802.1q VLAN.
See this link http://www.cisco.com/en/US/products/hw/routers/ps380/products_qanda_item0900aecd8028a982.shtml -
Cisco 7606 FIB Protocol Allocation mismatch after mls cef maximum-routes command
Hi,
we are trying to fine tune the mls cef maximum-routes without success for ipv4 on our Cisco 7606 router equiped like this:
Mod Ports Card Type Model Serial No.
2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL09169CP0
6 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAL10370YH7
Mod MAC addresses Hw Fw Sw Status
2 0013.c38b.ed9c to 0013.c38b.edb3 2.2 12.2(14r)S5 12.2(33)SRC1 Ok
6 0017.9441.b750 to 0017.9441.b753 5.2 8.4(2) 12.2(33)SRC1 Ok
Mod Sub-Module Model Serial Hw Status
2 Centralized Forwarding Card WS-F6700-CFC SAL09159C8T 2.0 Ok
6 Policy Feature Card 3 WS-F6K-PFC3BXL SAL10360CJ0 1.8 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL10360GNX 2.5 Ok
the show version is like this:
System image file is "bootdisk:c7600s72033-adventerprisek9-mz.122-33.SRC1.bin"
We tryied to set the value of the ipv4 FIB TCAM to 720k with this command:
mls cef maximum-routes ip 720
and then to save the configuration we used the "write" command. This was the output after we wrote the configuration:
FIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
User configured :-
IPv4 - 720k
MPLS - 16k (default)
IPv6 + IP Multicast - 144k (default)
Upon reboot :-
IPv4 - 720k
MPLS - 16k (default)
IPv6 + IP Multicast - 144k (default)
so we reloaded the router to get the new value.
when the router was up again it start to reload each 4 minutes. The FIB TCAM value was:
show mls cef maximum-routes
Reload scheduled for 13:50:09 DST Wed Aug 13 2014 (in 2 minutes and 51 seconds)
Reload reason: FIB Protocol Allocation mismatchFIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
User configured :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
Upon reboot :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
We know that our cisco is able to handle up to 1M of ipv4 routes inside the TCAM but we cannot set more than 512k ipv4 routes.
Why the router doesn't accept the new value?
Thanks
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/117712-problemsolution-cat6500-00.html
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/116132-problem-catalyst6500-00.html
https://supportforums.cisco.com/discussion/12250356/recommended-value-7600-ipv4-fib-tcamHi Paolo,
#sho ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI13, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 11-Mar-14 04:53 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
punk.gs2 uptime is 17 hours, 55 minutes
Uptime for this control processor is 17 hours, 55 minutes
Time since punk.gs2 switched to active is 17 hours, 54 minutes
System returned to ROM by reload at 22:32:30 BST Mon Sep 1 2014 (SP by reload)
System restarted at 22:35:24 BST Mon Sep 1 2014
System image file is "disk0:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C6504-E (R7000) processor (revision 2.0) with 983008K/65536K bytes of memory.
Processor board ID FOX11270F1B
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from power-on
11 Virtual Ethernet interfaces
50 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
#remote command switch show version
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI13, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 11-Mar-14 05:09 by prod_rel_team
ROM: System Bootstrap, Version 8.5(4)
punk.gs2 uptime is 17 hours, 55 minutes
Time since punk.gs2 switched to active is 17 hours, 55 minutes
System returned to ROM by reload at 22:32:30 BST Mon Sep 1 2014
System restarted at 22:34:17 BST Mon Sep 1 2014
System image file is "disk0:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin"
Last reload reason: Reload Command
cisco Catalyst 6000 (R7000) processor with 983008K/65536K bytes of memory.
Processor board ID FOX11270F1B
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
50 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
500472K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Hope that helps. -
Cisco SUP MGMT Interface Support L2 switchport mode?
Does the Cisco Supervisor MGMT interface support to be converted to a switchport to be assigned to a specific VLAN? The same question for 3750 switches and other switches.
No. They do need to have an IP address configured as they are actually routed ports.
The address needs to be in the subnet associated with the VLAN it plugs into in the switching infrastructure. -
How many VLANs supported via MACsec VLAN-trunk link?
Hi,
Any one know how many VLANs maximum allowed across a MACsec link between two C6500 with Sup2Ts or between two N7K respectively?
As far as I know, C3750X has limitation of 8 VLANs, according to
•Cisco TrustSec enforcement is supported only on up to eight VLANs on a VLAN-trunk link. If there are more than eight VLANs configured on a VLAN-trunk link and Cisco TrustSec enforcement is enabled on those VLANs, the switch ports on those VLAN-trunk links will be error-disabled.
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/software/release/15-0_2_se/configuration/guide/3750x_cg/trustsec.html
Thanks,
CedarHi,
Any one know how many VLANs maximum allowed across a MACsec link between two C6500 with Sup2Ts or between two N7K respectively?
As far as I know, C3750X has limitation of 8 VLANs, according to
•Cisco TrustSec enforcement is supported only on up to eight VLANs on a VLAN-trunk link. If there are more than eight VLANs configured on a VLAN-trunk link and Cisco TrustSec enforcement is enabled on those VLANs, the switch ports on those VLAN-trunk links will be error-disabled.
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/software/release/15-0_2_se/configuration/guide/3750x_cg/trustsec.html
Thanks,
Cedar -
image :c7600rsp72043-ipservicesk9-mz.122-33.SRE2.bin
i want monitor cisco 7606 information .but i only found some mib from cisco site .
i want to oid for cisco 7606-s so that i can monitor cpu memory and temperature.
thanks!Hi Winm,
http://tools.cisco.com/ITDIT/MIBS/MainServlet?IMAGE_NAME=c7600rsp72043-ipservicesk9-mz.122-33.SRE2.bin
...show you which OIDs are supported by your software version.
Try the following:
CPU under:
OLD-CISCO-CPU-MID
eg: 1.3.6.1.4.1.9.2.1.58
Memory under :
CISCO-MEMORY-POOL-MIB
eg: 1.3.6.1.4.1.9.9.48
Temperature:
CISCO-ENVMON-MIB
eg: 1.3.6.1.4.1.9.9.13.1.3.1.3
cheers,
Seb. -
hello, i have the cisco router (871) and when i try to create another vlan (another than vlan1 wich is default), i get the following message:
"vlan can not be added. Maximum number of 1 vlan(s) in the database"
with the command "show vtp status" i obtein:
"maximum vlans supported locally:1"
how can i change this???
i have read that i have to update my firmware and add a new flash card, is it true??
thank you very muchi would say try updating the ios image, i have c870-advipservicesk9-mz.124-6.T.bin and i have 8 possible vlans. also check your VTP version and post what it is
-
I was looking at the RV016, thinking that it might be perfect for a situation I have, and there seems to be many references in various forums for simpleVLAN support for this model, i.e. designating a range of physical ports to a VLAN. But the documentation on Cisco's site for this model makes no mention of VLAN support at all. Has it been removed from this model for some reason? Was this a feature on the pre-merger Linksys version that is now gone, or is the feature undocumented for some reason?
Hi Daniel,
You need to configure multiple subnets - in order to have 2 IP ranges.
Thann you need to chose different VLANs on 2 ports of RV016 (Port Management > Port Setup) - for example VLAN1 on port1 and VLAN2 on port 2 - thus you will separate the trafic on the 2 ports. You can connect your LAN on port1 and the AP for guest wifi on port2. Both subnets will have access to i-net, but not one to each other.
Regards,
Kremena
*Please rate the Post so other will know when an answer has been found. -
VLAN Support at routers and switches
is there a table with howmany VLANs each of cisco routers and switches can support.
its not always written at the product data sheet.hi
Do find the details for 1800 ISR series router..
802.1Q VLAN
A total of eight VLANs can be configured to segment a network and offer additional security and separation of network traffic.
VLAN Support
802.1Q VLAN supported on all 10/100BASE-T ports
VLAN Configured
8 VLANs
Wireless VLANs
16
7400 series has reached EOL/EOS status hence i couldnt find any datasheet for that model..
regds -
Cisco 7606 and out of band remote management
Hi
I have been trying to look for a document to confirm that Cisco 7606 support out of band remote management via Aux port. Can anyone please confirm whether 7606 support out of band remote management.
RegardsThe 7606 with a sup will only have a console port and no aux port.
Yes the console port supports OOB management using an external modem.
Thanks, Mak -
Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?
Hello all,
Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?
Best regards.Hi there, the link below outlines the ISE supported Cisco hardware:
http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/compatibility/ise_sdt.html
Thank you for rating helpful posts! -
CWLMS 3.1 : CiscoView of Cisco 7606-S Router
Hi Friend,
I am facing some issue with CiscoView of 7606-S router.
Please find the attachment for more details.
In figure, The RED Marked LAN port appears GREEN when viewed through CiscoWorks but physically on Cisco 7606-S router, no such port exists at all.
Also besides this, we have 3 fiber ports and 2 RJ-45 port on Cisco router visible through CiscoView, but physically on Cisco router 2 Fiber and 2 RJ-45 port are present.
first fiber port is up and connected whereas when seen through CiscoWorks, it shows 3rd fiber port as green.you can not display your 7600 in ciscoview, the most probably reason is that a device package is needed to do this. do the following:
1. Download the device package from the link (Cat6000IOS.cv50.v29-1.zip, Cat6000IOS.cv50.v29-1.readme)
http://www.cisco.com/cgi-bin/apps/vwplan/cvresult.cgi?product_class=Routers&product=Internet+Router+7600+IOS&application=All+Versions
2. Go to Common Services > Software Center > Device Update, then select CiscoView > click on 'Check for updates' > select 'Enter Server Path' and enter the path where you downloaded the files > continue the instructions to
install it.
This will probably need to restart ciscoworks to apply the changes. -
Hi all,
I have strange problem with anti spoof access-list which I would like to set up in cisco 7606 with 7600-PFC3CXL. So I made an access-list which is in [1.] and set up on interface Te1/1 like this [2.], but there are no match in output direction? Why? Well I made a test with [3.] but no matchs in access-list and ICMP was working than I made change [4.] and yeap icmp was not working and I have seen match in input direction good. It looks like that output direction in acl not working so I removed line 1 inc acl [4.] and icmp still not working and acl [3.] started matching icmp in line 1? Why? Can anybody help me? Thanks.
Karel
btw.> I tried solve this problem with this links:
http://www.cisco.com/en/US/docs/routers/7600/ios/12.2SR/configuration/guide/acl.html
http://www.cisco.com/web/about/security/intelligence/acl-logging.html
[1.]
Extended IP access list anti_spoof_Te1/1_input
10 deny ip 10.0.0.0 0.255.255.255 any
20 deny ip 172.16.0.0 0.15.255.255 any
30 deny ip 192.168.0.0 0.0.255.255 any
40 deny ip 127.0.0.0 0.255.255.255 any
50 deny ip 194.79.52.0 0.0.3.255 any
60 deny ip 0.0.0.0 0.255.255.255 any
70 permit ip any OUR CIDR
80 permit ip any host BGP Neighbor
90 deny ip any any
Extended IP access list anti_spoof_Te1/1_output
10 deny ip any 10.0.0.0 0.255.255.255
20 deny ip any 172.16.0.0 0.15.255.255
30 deny ip any 192.168.0.0 0.0.255.255
40 deny ip any 127.0.0.0 0.255.255.255
50 deny ip any 0.0.0.0 0.255.255.255
60 deny ip any OUR CIDR
70 permit ip host BGP Neighbor any
80 permit ip OUR CIDR any
90 deny ip any any
[2.]
ip access-group anti_spoof_Te1/1_input in
ip access-group anti_spoof_Te1/1_output out
[3.]
Extended IP access list anti_spoof_Te1/1_output
1 deny icmp host from OUR CIDR host in INTERNET log-input
10 deny ip any 10.0.0.0 0.255.255.255
20 deny ip any 172.16.0.0 0.15.255.255
30 deny ip any 192.168.0.0 0.0.255.255
40 deny ip any 127.0.0.0 0.255.255.255
50 deny ip any 0.0.0.0 0.255.255.255
60 deny ip any OUR CIDR
70 permit ip host BGP Neighbor any
80 permit ip OUR CIDR any
90 deny ip any any log-input
[4.]
Extended IP access list anti_spoof_Te1/1_input
1 deny icmp host from INTERNET host from OUR CIDR
10 deny ip 10.0.0.0 0.255.255.255 any
20 deny ip 172.16.0.0 0.15.255.255 any
30 deny ip 192.168.0.0 0.0.255.255 any
40 deny ip 127.0.0.0 0.255.255.255 any
50 deny ip 194.79.52.0 0.0.3.255 any
60 deny ip 0.0.0.0 0.255.255.255 any
70 permit ip any OUR CIDR
80 permit ip any host BGP Neighbor
90 deny ip any anyFollowing links may help you
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_white_paper09186a00801a1a55.shtml
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080120f48.shtml -
[Q]: OracleVM VLAN Support with same subnets
Can I create OracleVM Network VLAN pool that would allow for two vlans to use the same network topology or segment. Meaning, does the VLAN know how to tag the vlan I created to know which vlan the traffic came from and route back to the proper vlan. For example, VLAN1 - 192.168.1.0 and have any machines assigned to this vlan to only communicate with other machines on VLAN1. And have VLAN2 on the same network defined private segment with 192.168.1.0 network. BUT, is OVM aware of the tagging of VLAN1 and to route information back to the proper VLAN?
TIAVLAN tagging is independant - and of course must be, since it belongs to layer 2 of the OSI model, of the IP network that is run on it. You musn't confuse the network switches PVID (aka untagged VLAN support) which tagg an incoming packet on a switch port to a specific VLAN.
If you configure VLANs in OVM your're absolutely free to use whatever ip network you want on it - the traffic will stay seperated, since your're running it on a - although virtual - separate LAN.
Maybe you are looking for
-
Syncing iPhone and Outlook Calendar - bug?
I have an issue syncing my iPhone 3G Calendar with Outlook's Calendar (Outlook 2007). In general, the sync works fine, but: If I delete the current (ie first) instance of a repeating event in Outlook, when I sync, my iPhone will still display ALL ins
-
Should I be able to have PS, LR an BR open at once?
My system is so painfully slow since I started using CC this way. Sometimes I can't even get the brush, burn, dodge and other tools to appear at anything, but a little cross no matter size chosen. Below I've pasted my system info. Is it a hardware pr
-
How to create multiple workbooks in BI7 for a query
Hi all, I have created a query and saved it as a workbook.If I want to create second workbook for the same query what is the way for that ? I am unble to trace the path.can anyone help me on this ? Regards KK
-
Will online number send call to phone with Freetal...
Hello, I am interested in online number but I can't enough information. I have a phone hooked to skype via freetalk with a subscription. With online number, can I receive calls on that phone? What if I am logged in on mobile skype on my cell phone, w
-
Explaination of simple code?!?!?
hi, im new to java & to this forum. im a java noob!!! I was wonder if someone could explain to me how this code prints out 120 for "r"? (step by step) thx java genius's int [] x; int r; int i; /* 1 */ x = new int[] {2, 3, 4, 5, 6}; /* 2 */ r = 1; /*