Cisco 9900 (9951/9971) Show/Hide Video

Hi there,
Can I remove the Show/Hide Video option from the 9951/9971 Video Phones?
I need one phone as PLAR in a lobby which is fine but cannot remove this option.
Also wish to remove the "Preview Video" button.
Any ideas?
UCM 8.03
Chris

I've had a TAC case SR 629554885 open for this issue for about 2 months without resolution.  Specifically In our case I have an ASA at the remote end which drops the packet fragments as they appear as some type of attack due to the way they are fragmented.  This causes the phones to receive garbled video and eventually crash and reboot.  Did you ever find a workaround?

Similar Messages

  • Cisco SIP Phone 9971 won't register on CME 8.6 or 8.5 Please HELP

    Please help me , I have problem with registering Cisco SIP phone 9971 with CME 8.6 on ISR 2901.
    I configured CME for SIP clients, then I add configuration for 9971 phone and create profiles.  Phone downloaded SEP...xml file from CME,after that phone look for g4-tones.xml and gd-sip.jar files, I added them to CME after that phone downloaded them and reboot. Now phone is stuck in some kind of loop and does not register on CME.
    On phone log I can see repeting next few messeges.
    12:01:58a No DNS Server IP
    12:01:59a Updating Trust list
    12:01:59a No Trust List instaled
    12:01:59a SEP04C5AB03B0D.cnf.xml (TFTP)  // at this time phone download SEP...xml file from CME
    12:02:00a VPN Error: VPN is not Configured
    on CME if issue DEBUG TFTP EVENTS i receive next few lines
    *Aug 18 18:20:19.891: TFTP: Looking for CTLSEP04C5A4B03B0D.tlv
    *Aug 18 18:20:19.987: TFTP: Looking for ITLSEP04C5A4B03B0D.tlv
    *Aug 18 18:20:20.083: TFTP: Looking for ITLFile.tlv
    *Aug 18 18:20:20.347: TFTP: Looking for SEP04C5A4B03B0D.cnf.xml
    *Aug 18 18:20:20.351: TFTP: Opened flash:/SEP04C5A4B03B0D.cnf.xml, fd 14, size 4585 for process 141
    *Aug 18 18:20:20.363: TFTP: Finished flash:/SEP04C5A4B03B0D.cnf.xml, time 00:00:00 for process 141
    here you can see verison info of CME
    Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Thu 24-Mar-11 15:31 by prod_rel_team
    ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
    ELTOSAN_ROUTER uptime is 1 hour, 50 minutes
    System returned to ROM by reload at 16:29:20 UTC Thu Aug 18 2011
    System image file is "flash:/c2900-universalk9-mz.SPA.151-4.M.bin"
    Last reload type: Normal Reload
    Last reload reason: Reload Command
    Cisco CISCO2901/K9 (revision 1.0) with 471040K/53248K bytes of memory.
    Processor board ID FGL1508252Y
    3 Gigabit Ethernet interfaces
    2 terminal lines
    1 Virtual Private Network (VPN) Module
    4 Voice FXO interfaces
    4 Voice FXS interfaces
    1 Internal Services Module (ISM) with Services Ready Engine (SRE)
       Survivable Remote Site Voicemail (SRSV) on Cisco Unity Express (CUE) 8.5.1 in slot/sub-slot 0/0
    DRAM configuration is 64 bits wide with parity enabled.
    255K bytes of non-volatile configuration memory.
    254464K bytes of ATA System CompactFlash 0 (Read/Write)
    License Info:
    License UDI:
    Device#   PID                   SN
    *0        CISCO2901/K9          xxxxxxxxxxxxx
    Technology Package License Information for Module:'c2900'
    Technology    Technology-package          Technology-package
                  Current       Type          Next reboot
    ipbase        ipbasek9      Permanent     ipbasek9
    security      securityk9    Permanent     securityk9
    uc            uck9          Permanent     uck9
    data          None          None          None
    Configuration register is 0x2102
    this is RUNNING CONFIGURATION
    ! Last configuration change at 16:10:12 UTC Thu Aug 18 2011
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname ELTOSAN_ROUTER
    boot-start-marker
    boot system flash:/c2900-universalk9-mz.SPA.151-4.M.bin
    boot-end-marker
    no aaa new-model
    no ipv6 cef
    ip source-route
    no ip routing
    no ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 192.168.5.1 192.168.5.10
    ip dhcp excluded-address 192.168.5.200 192.168.5.255
    ip dhcp pool phone
       network 192.168.5.0 255.255.255.0
       default-router 192.168.5.251
       option 150 ip 192.168.5.251
    ip dhcp pool data
       relay source 192.168.2.0 255.255.255.0
       relay destination 192.168.2.201
    multilink bundle-name authenticated
    crypto pki token default removal timeout 0
    voice-card 0
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    fax protocol pass-through g711alaw
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 192.168.5.251 port 5060
    max-dn 6
    max-pool 6
    load 9971 sip9971.9-1-1SR1.loads
    authenticate register
    tftp-path flash:
    create profile sync 0005135312289902
    voice register dn  1
    number 207
    allow watch
    name GossaVM
    label 207
    voice register dn  3
    number 101
    name Dejan
    label 101
    mwi
    voice register pool  1
    id mac 000C.29C5.0011
    number 1 dn 1
    dtmf-relay sip-notify
    username testvm password testera
    codec g711alaw
    voice register pool  3
    id mac 04C5.A4B0.3B0D
    type 9971
    number 3 dn 3
    presence call-list
    dtmf-relay rtp-nte
    username dejan password 1234
    codec g711alaw
    no vad
    license udi pid CISCO2901/K9 sn xxxxxxxxxxxx
    hw-module ism 0
    hw-module pvdm 0/0
    redundancy
    interface GigabitEthernet0/0
    description INTERFACE INTERNAL
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    no mop enabled
    interface GigabitEthernet0/0.2
    description LAN DATA
    encapsulation dot1Q 2
    ip address 192.168.2.251 255.255.255.0
    no ip route-cache
    interface GigabitEthernet0/0.5
    description LAN VOICE
    encapsulation dot1Q 5
    ip address 192.168.5.251 255.255.255.0
    no ip route-cache
    interface ISM0/0
    no ip address
    no ip route-cache
    shutdown
    !Application: SRSV-CUE Running on ISM
    interface GigabitEthernet0/1
    no ip address
    no ip route-cache
    shutdown
    duplex auto
    speed auto
    interface ISM0/1
    description Internal switch interface connected to Internal Service Module
    shutdown
    interface Vlan1
    no ip address
    no ip route-cache
    shutdown
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    snmp-server community public RO
    tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
    tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
    tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
    tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
    tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
    tftp-server flash:sip9971.9-1-1SR1.loads alias sip9971.9-1-1SR1.loads
    tftp-server flash:United_States/g4-tones.xml
    tftp-server flash:English_United_States/gd-sip.jar
    control-plane
    voice-port 0/0/0
    voice-port 0/0/1
    voice-port 0/0/2
    voice-port 0/0/3
    voice-port 0/1/0
    voice-port 0/1/1
    voice-port 0/1/2
    voice-port 0/1/3
    mgcp profile default
    gatekeeper
    shutdown
    line con 0
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    line vty 0 4
    password jebiga
    login
    transport input all
    end
    I did not have any kind of problem with X-LITE to register to CME. also try with few SCCP phones 7940  and I did not any kind of problem .
    this is content of SEP....xml file for 9971
    <device>
    <deviceProtocol>SIP</deviceProtocol>
    <devicePool>
    <dateTimeSetting>
    <dateTemplate>M/D/YA</dateTemplate>
    <timeZone>Pacific Standard/Daylight Time</timeZone>
    <ntps>
    <ntp priority="0">
    <name>0.0.0.0</name>
    <ntpMode>unicast</ntpMode>
    </ntp>
    </ntps>
    </dateTimeSetting>
    <callManagerGroup>
    <members>
    <member priority="0">
    <callManager>
    <ports>
    <sipPort>5060</sipPort>
    </ports>
    <processNodeName>192.168.5.251</processNodeName>
    </callManager>
    </member>
    </members>
    </callManagerGroup>
    </devicePool>
    <sipProfile>
    <sipProxies>
    <registerWithProxy>true</registerWithProxy>
    </sipProxies>
    <sipCallFeatures>
    <cnfJoinEnabled>true</cnfJoinEnabled>
    <localCfwdEnable>true</localCfwdEnable>
    <callForwardURI>service-uri-cfwdall</callForwardURI>
    <callPickupURI>service-uri-pickup</callPickupURI>
    <callPickupGroupURI>service-uri-gpickup</callPickupGroupURI>
    <callHoldRingback>2</callHoldRingback>
    <semiAttendedTransfer>true</semiAttendedTransfer>
    <anonymousCallBlock>2</anonymousCallBlock>
    <callerIdBlocking>2</callerIdBlocking>
    <dndControl>2</dndControl>
    <remoteCcEnable>true</remoteCcEnable>
    </sipCallFeatures>
    <sipStack>
    <remotePartyID>true</remotePartyID>
    </sipStack>
    <sipLines>
    <line button="1" lineIndex="1">
    <featureID>9</featureID>
    <featureLabel></featureLabel>
    <proxy>USECALLMANAGER</proxy>
    <port>5060</port>
    <name></name>
    <displayName></displayName>
    <autoAnswer>
    <autoAnswerEnabled>2</autoAnswerEnabled>
    </autoAnswer>
    <callWaiting>1</callWaiting>
    <authName>dejan</authName>
    <authPassword>1234</authPassword>
    <sharedLine>false</sharedLine>
    <messagesNumber></messagesNumber>
    <ringSettingActive>5</ringSettingActive>
    <forwardCallInfoDisplay>
    <callerName>true</callerName>
    <callerNumber>true</callerNumber>
    <redirectedNumber>true</redirectedNumber>
    <dialedNumber>true</dialedNumber>
    </forwardCallInfoDisplay>
    </line>
    <line button="2" lineIndex="2">
    <featureID>9</featureID>
    <featureLabel>101</featureLabel>
    <proxy>USECALLMANAGER</proxy>
    <port>5060</port>
    <name>101</name>
    <displayName>Dejan Rakic</displayName>
    <autoAnswer>
    <autoAnswerEnabled>2</autoAnswerEnabled>
    </autoAnswer>
    <callWaiting>1</callWaiting>
    <authName>dejan</authName>
    <authPassword>1234</authPassword>
    <sharedLine>false</sharedLine>
    <messagesNumber></messagesNumber>
    <ringSettingActive>5</ringSettingActive>
    <forwardCallInfoDisplay>
    <callerName>true</callerName>
    <callerNumber>true</callerNumber>
    <redirectedNumber>true</redirectedNumber>
    <dialedNumber>true</dialedNumber>
    </forwardCallInfoDisplay>
    </line>
    </sipLines>
    <enableVad>true</enableVad>
    <preferredCodec>g711alaw</preferredCodec>
    <dialTemplate></dialTemplate>
    <kpml>1</kpml>
    <phoneLabel></phoneLabel>
    <stutterMsgWaiting>2</stutterMsgWaiting>
    <disableLocalSpeedDialConfig>true</disableLocalSpeedDialConfig>
    <dscpForAudio>184</dscpForAudio>
    <dscpVideo>136</dscpVideo>
    </sipProfile>
    <commonProfile>
    <phonePassword>1234</phonePassword>
    <callLogBlfEnabled>2</callLogBlfEnabled>
    </commonProfile>
    <featurePolicyFile>featurePolicyDefault.xml</featurePolicyFile>
    <loadInformation>sip9971.9-1-1SR1.loads</loadInformation>
    <vendorConfig>
    </vendorConfig>
    <commonConfig>
    <videoCapability>0</videoCapability>
    <ciscoCamera>0</ciscoCamera>
    </commonConfig>
    <sshUserId>dejan</sshUserId>
    <sshPassword>1234</sshPassword>
    <userId></userId>
    <phoneServices>
    <provisioning>2</provisioning>
    <phoneService  type="1" category="0">
    <name>Missed Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/MissedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="1" category="0">
    <name>Received Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/ReceivedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="1" category="0">
    <name>Placed Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/PlacedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="2" category="0">
    <name>Voicemail</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/Voicemail</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    </phoneServices>
    <versionStamp>0131511014412102</versionStamp>
    <userLocale>
    <name>English_United_States</name>
    <langCode>en</langCode>
    </userLocale>
    <networkLocale>United_States</networkLocale>
    <networkLocaleInfo>
    <name>United_States</name>
    </networkLocaleInfo>
    <authenticationURL></authenticationURL>
    <directoryURL></directoryURL>
    <servicesURL>http://192.168.5.251:80/CMEserverForPhone/serviceurl</servicesURL>
    <dscpForSCCPPhoneServices>0</dscpForSCCPPhoneServices>
    <dscpForCm2Dvce>96</dscpForCm2Dvce>
    <transportLayerProtocol>2</transportLayerProtocol>
    </device>

    Hello,
    I'm facing exactly the same problem, that is:
    a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
    I have read all the postings to this Forum, but I have not been able to solve it.
    In my case the commands voice register dn  and  voice register pool are OK.
    So frankly, I have no idea what I could be missing.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

  • Cisco SIP Phone 9971 won't register on CME 8.6

    Hello,
    I'm facing a very strange problem:
    a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
    I have read all the related-postings to this and other Forum, but I have not been able to solve it.
    One of the "potential solutions" was to make sure that the Phone had a Line configured.
    But I think that the commands voice register dn  and  voice register pool are properly configured (see config below)
    So frankly, I have no idea what I could be missing.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

    Thank you for your reply.
    I did some debugs and the results are very strange!
    This is what I got:
    Feb 24 18:01:12.219: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 400 Bad Request
    Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK08011844
    From: ;tag=189c5db6bd09000260cf3daf-289a76d1
    To: ;tag=52488-160A
    Date: Mon, 24 Feb 2014 18:01:12 GMT
    Call-ID: [email protected]
    CSeq: 1000 REFER
    Content-Length: 0
    Contact:
    Feb 24 18:01:12.291: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    REGISTER sip:172.25.140.1 SIP/2.0
    Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK1e9ad079
    From: ;tag=189c5db6bd0900032df02e9c-25d79707
    To:
    Call-ID: [email protected]
    Max-Forwards: 70
    Date: Fri, 01 Jan 1982 00:02:41 GMT
    CSeq: 101 REGISTER
    User-Agent: Cisco-CP9971/9.4.1
    Contact: ;+sip.instance="
    000000-0000-0000-0000-189c5db6bd09>";+u.sip!devicename.ccm.cisco.com="SEP189C5DB
    6BD09";+u.sip!model.ccm.cisco.com="493";video
    Supported: replaces,join,sdp-anat,norefersub,resource-priority,extended-refer,X-
    cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-
    cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-6.0.2,X-cisco-xsi-
    8.0.1
    Content-Length: 0
    Reason: SIP;cause=200;text="cisco-alarm:22 Name=SEP189C5DB6BD09 ActiveLoad=sip99
    71.9-4-1-9.loads InactiveLoad=sip9971.9-3-2SR1-1.loads Last=reset-reset"
    Expires: 3600
    Feb 24 18:01:12.395: voice_reg_get_reg_expires_timer: no voice register pool found
    Feb 24 18:01:12.395: VOICE_REG_POOL: Register request for (1010) from (172.35.140.12)
    Feb 24 18:01:12.395: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
    Feb 24 18:01:12.395: VOICE_REG_POOL: key(1010) contact(172.35.140.12:5060) add to contact table
    Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (1010) found in contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(1010) contact(172.35.140.12) added to contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) add to srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) added to srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    But right after these errors, I get the following:
    Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
    1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    VOICE_REG_POOL pool_tag(1), dn_tag(1)
    Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
    Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
    Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
                                   Name:SEP189C5DB6BD09 IP:172.35.140.12  DeviceType:Phone
    Feb 24 18:01:12.411: VOICE_REG_POOL: Pool[1]: service-control (reset type: 2) message sent to sip:[email protected]
    Feb 24 18:01:12.411: voice_reg_privacy_update_to_phone: delay sending privacy update during bulk registration
    Feb 24 18:01:12.415: //1/7B0070C28003/SIP/Msg/ccsipDisplayMsg:
    ====================
    And when I do a sh voice register pool, I get the following:
    C2811#sh voice register pool  1
    Pool Tag 1
    Config:
      Mac address is 189C.5DB6.BD09
      Type is 9971
      Number list 1 : DN 1
      Proxy Ip address is 0.0.0.0
      Current Phone load version is Cisco-CP9971/9.4.1
      DTMF Relay is enabled, rtp-nte
      Call Waiting is enabled
      DnD is disabled
      Video is enabled
      Camera is enabled
      Busy trigger per button value is 0
      call-forward b2bua busy 68600
      keep-conference is enabled
      registration expires timer max is 3600 and min is 120
      username adm password adm
      kpml signal is enabled
      Lpcor Type is none
      blf call list is enabled
      Transport type is udp
      service-control mechanism is supported
      registration Call ID is [email protected]
      Registration method: per line
      Privacy feature is not configured.
      Privacy button is disabled
      active primary line is: 1010
      contact IP address: 172.35.140.12 port 5060
      Phone SIS Version:  6.0.2
      GW SIS Version:  1.0.0
    Dialpeers created:
    Dial-peers for Pool 1:
    dial-peer voice 40001 voip
    destination-pattern 1010
    session target ipv4:172.35.140.12:5060
    session protocol sipv2
    dtmf-relay rtp-nte
    digit collect kpml
    codec  g711ulaw bytes 160
    no vad
      call-fwd-busy        68600
      after-hours-exempt   FALSE
    Statistics:
      Active registrations  : 4
      Total SIP phones registered: 1
      Total Registration Statistics
        Registration requests  : 4
        Registration success   : 4
        Registration failed    : 0
        unRegister requests    : 0
        unRegister success     : 0
        unRegister failed      : 0
        Attempts to register
               after last unregister : 0
        Last register request time   : 18:11:43.551 UTC Mon Feb 24 2014
        Last unregister request time :
        Register success time        : 18:11:43.551 UTC Mon Feb 24 2014
        Unregister success time      :
    C2811#
    So apparently the Phone is actually registered!
    However, the Phone screens still shows this message: Phone Not Registered.
    So frankly I don't understand what's going on!
    I really hope somebody can help.  Thanks!

  • Cisco SIP Phone 9971 will not register on CME 8.6

    Hello,
    I'm trying to configure a  Cisco SIP Phone 9971,
    but it won't register on CME 8.6, which is running on a 2811
    The Phone shows this error message: Phone Not Registered.
    And when I check the the Status Messages in the Phone, I see the following:
    VPN Error: vpn is not configured
    Actually, it shows all these 4 messages in a constant Loop:
    12:01:59a SEP189C5DB6BD09.cnf.xml (TFTP)
    12:01:59a No Trust List instaled
    12:01:59a Updating Trust list
    12:02:00a VPN Error: VPN is not Configured
    It seems that this VPN Error is keeping the Phone from registering.
    This is repeated for ever and the Phone never registers; at least that's what it appears.
    However, when I do a sh voice register pool, I get the following:
    C2811#sh voice register pool  1
    Pool Tag 1
    Config:
      Mac address is 189C.5DB6.BD09
      Type is 9971
      Number list 1 : DN 1
      Proxy Ip address is 0.0.0.0
      Current Phone load version is Cisco-CP9971/9.4.1
      DTMF Relay is enabled, rtp-nte
      Call Waiting is enabled
      DnD is disabled
      Video is enabled
      Camera is enabled
      Busy trigger per button value is 0
      call-forward b2bua busy 68600
      keep-conference is enabled
      registration expires timer max is 3600 and min is 120
      username adm password adm
      kpml signal is enabled
      Lpcor Type is none
      blf call list is enabled
      Transport type is udp
      service-control mechanism is supported
      registration Call ID is [email protected]
      Registration method: per line
      Privacy feature is not configured.
      Privacy button is disabled
      active primary line is: 1010
      contact IP address: 172.35.140.12 port 5060
      Phone SIS Version:  6.0.2
      GW SIS Version:  1.0.0
    Dialpeers created:
    Dial-peers for Pool 1:
    dial-peer voice 40001 voip
    destination-pattern 1010
    session target ipv4:172.35.140.12:5060
    session protocol sipv2
    dtmf-relay rtp-nte
    digit collect kpml
    codec  g711ulaw bytes 160
    no vad
      call-fwd-busy        68600
      after-hours-exempt   FALSE
    Statistics:
      Active registrations  : 4
      Total SIP phones registered: 1
      Total Registration Statistics
        Registration requests  : 4
        Registration success   : 4
        Registration failed    : 0
        unRegister requests    : 0
        unRegister success     : 0
        unRegister failed      : 0
        Attempts to register
               after last unregister : 0
        Last register request time   : 18:11:43.551 UTC Mon Feb 24 2014
        Last unregister request time :
        Register success time        : 18:11:43.551 UTC Mon Feb 24 2014
        Unregister success time      :
    C2811#
    This sh voice register pool  seems to indicate that the Phone has actually registered.
    But I still get the  Phone Not Registered   message on the screen!
    I did some Debugs and they also seem to indicate that the Phone has indeed registered:
    Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
    1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    VOICE_REG_POOL pool_tag(1), dn_tag(1)
    Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
    Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
    Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
                                   Name:SEP189C5DB6BD09 IP:172.35.140.12  DeviceType:Phone
    So frankly, I have no idea why the Phone keeps showing the Phone Not Registered message.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

    VPN is not Configured prints on all phones now with the built-in VPN client if VPN isn't configured.  That's normal and is just cosmetic.  That should not be causing your registration issues.

  • How to hide video length informaiton

    Dear all,
    I created a landing webpage with embedded video hosted on Vimeo. When I use Safari on iPhone 5 to visit the webpage and click the video link it always shows the video length information, which I want to hide. I am wondering if I can do any customization on the video iframe code in order to hide that information ? Please kindly advise, thank you very much all folks.
    Yours sincerely,
    Kenny

    There isn't an option per se.
    However there is an app in AppWorld that will let you do it.
    Personally, I just use the Air Browser in AppWorld to rename the file extension from .mp4 to .mp4.me.
    This hides the video from the player until I name it back again.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!

  • Show/hide pointer issue

    Show pointer option is not working as it used to be with last 2 versions of photoshop touch for iphone on iphone 6.
    While making a selection with lasso tool with "show pointer on" I can not carry on selection step by step, it works a few steps properly then I had to wait for a while so that it can go further step.

    I apologize for the confusion. Let me try to start over, following the instructions you are asking to provide. The computer that has Photoshop installed is from school, so I will try the best I can giving you detailed specs. For what I know, It is a PC running Windows 7 64bit, but I do not know the amount of RAM as I do not have permission to access the control panel or any of its system settings. The version of Photoshop is CS6 13.0 Extended, and its performance preferences re the following...
    Available Ram: 34827MB
    IdealRange: 1884-2467MB
    Allow Photoshop to use: 2056MB
    HardDrive: 835GB
    as for the error, there is no error. I might of not been specific, but I am not stupid not to include the type of error if there was any...
    Other things like the grand total ram, video card, and video ram are all accessible by the administrator only.
    the file I am working on, is an imported 3ds Max file. I was trying to use Photoshop's 3D painting tool, and from what I understand, it is possible to hide polygons by selecting an area you would like to keep, and what is not selected gets hidden. This is supposed to be good for painting areas that are behind parts of the mesh that is in the way. From the instruction, you are suppose to select the area that you want to keep, and then choose 3d->Show/Hide Polygons->Within Selection. This part I was able to do. Once I was happy with what I needed to paint, I then selected 3d->Show/Hide Polygons-> invert. This allowed me to continue painting other hard areas of the mesh by revealing what was hidden and hides what is visible. Then, when I was ready to reveal the entire mesh back, I was thinking that I should be able to do this by clicking on 3d->Show/Hide Polygon->Reveal All. However, this only reverts the visibility back the other way around as if I clicked on revert.
    So what I was wondering is if this is how the 3d reveal all tool works or is this a bug?
    I hope this clear things up, if not, please let me know.

  • How to show/hide invisible characters in Mac Keynote 6?

    How can I show/hide the invisible characters in Mac Keynote 6?

    we call them non printing characters
    this cant be displayed in Keynote, Keynote is a video based presentation application and does not have many typographic tools.
    The sister application to Keynote is Pages which can show non printing characters so you should use that;
    View > show > invisibles

  • Photoshop CS6 Show/Hide Polygons issue

    Hi. I am doing an assignment for class, using Photoshop CS6, and I am having problems with the show/hide polygons feature. After hiding the polygons of the unselected area, I am able to reveal the entire object by choosing "Reveal All". However, if I ever need to invert the other polygons, by choosing 'Invert Visible", and then want to reveal the entire object again, all it does is inverts it back the other way around. Is this a bug, or is this how it works?

    I apologize for the confusion. Let me try to start over, following the instructions you are asking to provide. The computer that has Photoshop installed is from school, so I will try the best I can giving you detailed specs. For what I know, It is a PC running Windows 7 64bit, but I do not know the amount of RAM as I do not have permission to access the control panel or any of its system settings. The version of Photoshop is CS6 13.0 Extended, and its performance preferences re the following...
    Available Ram: 34827MB
    IdealRange: 1884-2467MB
    Allow Photoshop to use: 2056MB
    HardDrive: 835GB
    as for the error, there is no error. I might of not been specific, but I am not stupid not to include the type of error if there was any...
    Other things like the grand total ram, video card, and video ram are all accessible by the administrator only.
    the file I am working on, is an imported 3ds Max file. I was trying to use Photoshop's 3D painting tool, and from what I understand, it is possible to hide polygons by selecting an area you would like to keep, and what is not selected gets hidden. This is supposed to be good for painting areas that are behind parts of the mesh that is in the way. From the instruction, you are suppose to select the area that you want to keep, and then choose 3d->Show/Hide Polygons->Within Selection. This part I was able to do. Once I was happy with what I needed to paint, I then selected 3d->Show/Hide Polygons-> invert. This allowed me to continue painting other hard areas of the mesh by revealing what was hidden and hides what is visible. Then, when I was ready to reveal the entire mesh back, I was thinking that I should be able to do this by clicking on 3d->Show/Hide Polygon->Reveal All. However, this only reverts the visibility back the other way around as if I clicked on revert.
    So what I was wondering is if this is how the 3d reveal all tool works or is this a bug?
    I hope this clear things up, if not, please let me know.

  • Movies, TV Shows, Music Videos from iCloud not showing up in Videos app

    So I just did a reset on my iPhone because the movie artwork for the movie Love Actually was a picture of Adele's album artwork and it really bothered me. All the other movies in the Videos app was fine, they all matched to their respective titles. So I did a reset hoping that would fix that tiny minor issue but after doing the reset and restoring, None of the movies I've purchased in the past are showing up. All it says is "No Content. You can download videos from the iTunes Store." And I did go into the Videos settings to make sure "Show All Videos" is being set to on (green) but it still did nothing, none of my movies, tv shows, or music videos are showing up in the cloud. This really irritates me because I had one small issue that I was hoping to fix but now a new problem has risen and it's going to bug the **** out of me more than the original problem did. I tried turning it off and turining it back on, signing in and out of iTunes account, and pressing the power button and the home button at the same time, but still nothing from iCloud has appeared, Is anybody else having this issue? FYI, I also have the latest update 7.0.4 but I don't think that should have caused this issue. If anybody knows a solution, please let me know because as you can see, I'm very OCD about this, I like to see all my videos in the Videos app.

    This was driving me nuts, but I figured it out. Here's how to fix:
    1) Create (or find) a thumbnail image that represents the series to you (I put text over a screenshot) in Photoshop or whatever you like to use, and put it on the clipboard
    2) In iTunes, select all the episodes from your series in the TV Shows view, right click, and select "Get Info"
    3) On the first tab ("Info") click in the artwork field, then paste in the thumbnail
    4) THIS IS THE KEY STEP - With your iPad plugged into your Mac, go to the TV shows tab and uncheck "Sync TV Shows" and then apply the new settings, and say okay when it tells you all your TV shows will be removed from your iPad
    5) After the sync is complete, check to make sure all your TV shows are gone (in the video app, there shouldn't even be a tab for TV Shows)
    6) In iTunes, check Sync TV Shows again, then apply
    Once the sync is complete, your TV Shows will hopefully show up with good thumbnails.
    The issue seems to be that once a file has been copied over, updating the thumbnail image in iTunes will NOT force an update on the iPad, and in the TV Shows view there are no captions on the main screen. You have to delete all the files to wipe the DB on the iPad.

  • Issue with page processing - confirmation message & show /hide a button..

    Hello,
    I am working on a to do list application.
    I have events and for each event, I show list of tasks (grouped in reports based on the calculated task's status).
    In one region I have a drop down list of events and a Select Event button.
    For each task, I had to create a CLOSE option (initially I used a link, but the requester wanted a confirmation before closing the task).
    Now I have a checkbox for each task (generated dynamically with apex_item.checkbox(1,task_id)).
    Closing a task in my application means to set the end_date to sysdate.
    I followed the instructions from
    http://download-west.oracle.com/docs/cd/B31036_01/doc/appdev.22/b28839/check_box.htm#CEGEFFBD. I've created also a button and a process and updated the sql from "delete" to "update".
    The process is set: OnSubmit - After Computations and Validations; Run Process Once per page visit (default).
    The issue number 1 is that I see the confirmation message (that tasks have been closed) every time I reload the page (the same when I click Select_event button).. not only after I press on that Close_task button..
    For issue number 2, I have to mention that I've added a condition to show / hide the Close_task button, only if I have at least 1 task in the report.
    The issue number 2 is that I see the button only if I click 2 times on the Select_Event button.. The same is for hide.
    I feel like I am missing something very important about how to synchronize different events(buttons clicks), processes..
    help..?
    Thank you!
    Anca

    This forum is magic..
    As soon as write here, I find the answer!
    Issue 1: I fixed it by specifying this: When Button Pressed (Process After Submit When this Button is Pressed) and my button. I miseed this 1st time.
    Issue 2: I moved the button after the report.. and now it's working just fine!
    I did this about it for some time before asking the question here.. but I just had to write here and got the right answer ;)
    Have a nice day!
    Anca

  • I downloaded some videos to Premier Elements 13 from external hard drive but now the external hard drive is damaged. I tried to open the videos on the organizer which it shows the video but with a yellow ? and says missing file. Is there anyway I can open

    I downloaded some videos to Premier Elements 13 from an external hard drive but now the external hard drive is damaged. While setting up my new MAC the external hard drive was dropped and I have been told by an outside source they could not retrieve the files.  It had 4 years of photos and videos on it. I remembered that I had downloaded some of the videos from the external hard drive (before it was broke) to Adobe Organizer 13 when I installed the Adobe 13 on my MACOS X 10.9.5.  I tried to open the videos on the organizer which it shows the video but with a yellow ? and says missing file. Is there anyway I can open these videos?
    Any input is greatly appreciated!! I am sick over losing the videos and had a little hope on Adobe Organizer until I was unable to open them.  I am thinking it is due to my external hard drive not being plugged in. I thought when I transferred from the external hard drive to Adobe 13 that it would be there without the external hard drive needing to be attached but maybe I did something wrong.
    Thanks again for any help!!!!

    jnrmendonca
    It had 4 years of photos and videos on it.
    To what did your camera record those photos and videos - camera's internal memory, inserted memory card, other?
    Any remote chance that the latter may still exist for you to use to download the camera files to your new external hard drive?
    ATR

  • How to make a layer from the ADF pivot table invisible , show-hide column-row-data

    Hello all ,
    I need to create a pivottable with ADF 12c for reporting purposes.
    I have a table or view with 10 items of type VARCHAR2 , C1,C2,C3,C4,C5,C6,C7,C8,C9,C10  and   10 items of type NUMBER N1,N2,N3,N4,N5,N6,N7,N8,N9,N10
    The items of type VARCHAR2 are for Column and Row areas and the items NUMBER are for Data Areas
    I want to create a jsf page with one empty pivottable and in code Show or Hide the items in the Column area , Row area , Data area
    Con you send me a small sample ?
    I test with this code that i find in oracle OTN but not work.
    <dvt:pivotTable id="pt2" value="#{bindings.WebPivotDataView1.pivotTableModel}" var="cellData"
    varStatus="cellStatus" splitMode="enabled"
    binding="#{backingBeanScope.CmfPivotBean.pivotTable}"
    >
    <dvt:headerCell>
    <af:switcher facetName="#{cellData.layerName}" defaultFacet="Default" id="s1">
    <f:facet name="DataLayer">
    <af:outputText value="#{cellData.label}" id="ot1"/>
    </f:facet>
    <f:facet name="C01">
    <af:outputText value="#{cellData.dataValue}" id="ot2"/>
    </f:facet>
    <f:facet name="Default">
    <af:outputText value="#{cellData.dataValue}" id="ot3"/>
    </f:facet>
    </af:switcher>
    </dvt:headerCell>
    <dvt:dataCell>
    <af:switcher facetName="#{cellStatus.members.DataLayer.value}" defaultFacet="Default" id="s2">
    <f:facet name="N01">
    <af:outputText value="#{cellData.dataValue}" id="ot4">
    <af:convertNumber groupingUsed="false"
    pattern="#{bindings.WebPivotDataView1.hints.N01.format}"/>
    </af:outputText>
    </f:facet>
    <f:facet name="Default">
    <af:outputText value="#{cellData.dataValue}" id="ot5"/>
    </f:facet>
    </af:switcher>
    </dvt:dataCell>
    </dvt:pivotTable>
    DCBindingContainer bindingContainer = (DCBindingContainer)ADFContext.getCurrent().getRequestScope().get("bindings");
    CubicBinding cubicBinding = (CubicBinding)bindingContainer.findCtrlBinding("WebPivotDataView1");
    CubicEditor cubicEditor = cubicBinding.getCubicEditor();
    cubicEditor.removeLayer(DataDirector.ROW_EDGE, 0); //remove 1st row edge
    cubicEditor.removeLayer(DataDirector.COLUMN_EDGE, 0); // remove 1st column edge
    cubicEditor.removeDataItem(0);
    CubicDefinition def;
    def = cubicBinding.getProjection();
    LayerDefinition layerDefinition = new LayerDefinition("C3");
    cubicEditor.addLayer(DataDirector.ROW_EDGE, 0, layerDefinition);    
    LayerDefinition layerDefinition2 = new LayerDefinition("C4");
    cubicEditor.addLayer(DataDirector.COLUMN_EDGE, 0, layerDefinition2);
    DataItemDefinition def3 = new DataItemDefinition("N1");
    cubicEditor.addDataItem(def3);
    AdfFacesContext.getCurrentInstance().addPartialTarget(pivotTable);
    Can you help me if is possible to create a pivottable binding to a one ViewObject and in code show/hide or compose the layout of the pivottable ??
    I search in google and OTN oracle and not find any code.
    Only find the code of the samples that is very complex for me , the code of the samples create the PivotTableModel from one Array , and i want to binding from one ADB BC ViewObject.
    Thanks in advance

    The solution I presented for your use case an DOAG 2013 was to create a pivot table binding out of user defined attributes from the table. For the defined attributes a VO is dynamically created as well as the pivot binding. The pivot binding is then exchanged at runtime together with the activation of the dynamic VO needed to only get the data needed for the particularly pivot table.
    Your solution using the CubicEditor is hard to implement due to the missing documentation. This was the reason I did not follow this approach, However it's not impossible (done it on a very small scale).
    None of the solution are what I call simple. They are complicated, complex and in part not supported solution (exchanging the pivot table binding at runtime need to use internal classes, which is not supported).
    I can't give you a working sample as it's too complex. I can make the slides available, however they are in German.
    Timo

  • My left shift key on Macbook Pro Retina (15") is behaving like the F11 key (show/hide open windows).  The key behaves the same for the laptop keyboard and for an external Apple keyboard?  This just started in last week after 6 months of use

    My left shift key on Macbook Pro Retina (15") is behaving like the F11 key (show/hide open windows). 
    The left shift key behaves the same on the laptop keyboard and on an external Apple keyboard. 
    This just started in last week after 6 months of use.  The right shift key and other keys on the keyboard all appear to work correctly.
    Suggestions greatly appreciated.

    I have a solution to this issue now after a discussion with Apple Support.  Some where in the last few weeks, there was a change in the key that would do a Show Desktop under the Mission Control settings in the System Preferences.  Even though the key sequence that was shown for the Show Desktop setting did not include the Left SHift key, by changing this first to having no key sequence and applying that and then changing it back to the F11 key, the Left SHift key issue that I was having has cleared up.
    A second issue that was uncovered was that the SSD had some issues (uncovered when I ran Disk Utility using the Repair Disk key).  I had to restart and use the Disk Utility through the Command R sequence to get to the stand alone Disk Utility.  The SSD appears to be running better as a result as well.
    Hope that this is of use to someone else in the future.

  • How do you allow firefox to toggle show/hide menus

    I am using a website that has a show/hide text toggle. When I click the show button, it opens a new blank tab. I tested this on google chrome as well and it works properly. There must be a setting in firefox to correct this but I don't know what it is.

    Such a hide/show action is usually done via a JavaScript onclick event.
    If you get a new tab or window then this would suggest that the onclick isn't working and that the href is used and opens the new tab.
    You could check via the right-click context menu in the Inspector if there is an 'ev' button appended to this link (button).
    *https://developer.mozilla.org/Tools/Page_Inspector
    You can try these steps in case of issues with web pages:
    You can reload web page(s) and bypass the cache to refresh possibly outdated or corrupted files.
    *Hold down the Shift key and left-click the Reload button
    *Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
    *Press "Command + Shift + R" (Mac)
    Clear the cache and remove cookies only from websites that cause problems.
    "Clear the Cache":
    *Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
    "Remove Cookies" from sites causing problems:
    *Firefox/Tools > Options > Privacy > "Use custom settings for history" > Cookies: "Show Cookies"
    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
    *Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
    *Do NOT click the Reset button on the Safe Mode start window
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

  • Show/Hide conditional text at a book level

    I am using TCS2 on Windows XP.
    FM 9.0 p250
    I have several files as part of a large FM book. Each file has the same text conditional tags. Can I, at a book level, set my conditions to show/hide, etc. and then update the book? So far, I only know how to open each file, set the SHOW/HIDE CONDITIONAL TEXT as I need it (not to show conditiona indicators and according to my built expression) and then save and close each file.
    Is there a way to do all my files at once? Note- I want them all set the same way... so that might make it easier..
    Thanks,
    Adriana

    adrianaharper wrote:
    I am using TCS2 on Windows XP.
    FM 9.0 p250
    I have several files as part of a large FM book. Each file has the same text conditional tags. Can I, at a book level, set my conditions to show/hide, etc. and then update the book? So far, I only know how to open each file, set the SHOW/HIDE CONDITIONAL TEXT as I need it (not to show conditiona indicators and according to my built expression) and then save and close each file.
    Is there a way to do all my files at once? Note- I want them all set the same way... so that might make it easier..
    Thanks,
    Adriana
    I don't have FrameMaker available right now, so I'm working from memory, using the traditional FrameMaker menus, rather than the FM 9 tools.
    Select all the files in the book window. With the book window active, open the View menu and look for Conditional Text. Your settings here apply to all selected files in the book window, so it's possible to set conditions on all or some files files. Ctrl+Click to select non-contiguous files; Shift+Click to select a range of contiguous files.
    HTH
    Regards,
    Peter
    Peter Gold
    KnowHow ProServices

Maybe you are looking for

  • 2.1 RC1 - Pure performance when Preferences.Worksheet."script path" is used

    When I fill out the "Select default path to look for scripts" text box on the Worksheet page in Preferences, I expirience very bad performance when I type in sql statements. If I clear the text box agian, I have normal performance.

  • How to check message ID

    Hi everyone! How do I check the messages that a certain transaction produce? For example, the TCODE F-02. How do I check what are the possible messages that it will produce? Thanks!

  • BI Publisher configured with BI Server Security not working for the admins.

    Hello Everyone, I have configured the BI publisher to work with the BI server security. Everything is working well with the exception that all users part of the BI Server "Administrators" group are unable to login and get the following error message

  • Web application session state in Oracle

    In .Net 2.0, it is possible to store session states of web applications in other databases than SQL Server. Does any one have stored session state in Oracle? What should be done? Thanks

  • Quicktime and all quicktime-using applications crash on startup

    A while ago my computer crashed and wouldn't start up. We ran the disk utility and fixed the permissions and ran disk warrior, and in the end we eventually got it to work by installing MacOS onto the harddrive again (so basically it's installed twice