Cisco ACS 5.5 username and password

Hi All
I have defined username and password for one of the users to login to the routers.
I have set the password.
Can please advise how do I make him change the password after his first login with the given username and password.
Thanks

While creating a user under Users and Identity Stores > Internal Identity Store > Users > createe. Check this box to start the process to change the user’s password at the next user login, after authentication with the old password.
http://www.cisco.com/c/en/us/td/docs/net_mgmt/cisco_secure_access_control_system/5-5/user/guide/acsuserguide/users_id_stores.html#49082
Regards,
Jatin Katyal
*Do rate helpful posts*

Similar Messages

Configure a Cisco router with telnet Username and Password.

Hello Guys,
Am quite new in cisco and i need to configure an 891 cisco router,can someone please show me step by step configuration commands for configuring Username and Secret Password.I would like the router to ask for "Username"and " Password" anytime i want to login the router through telnet.I also want to know if i have to erase the default configurations on the router first, before i start the configuration,and how it should be done in other not to loose the router whiles working on it.Thanks for your usual quick responds.
Regards,
Eben.

From this forum description:
Note: If your questions pertain to specific Cisco technology or solution, please post them in the proper community by leveraging the Community Directory so that folks who have expertise within those areas can engage and collaborate to it.
You should consider to delete your question here and recreate in in more appropriate forum. You can wish for quick response then ...
Edit: Thread has been moved by moderator, the notice no longer apply.

ACS v3.2 Default Username and Password

Dear All,
Do you know what is the default login username and password for ACS v3.2?
Besides, If I forget the password, is there any password recovery procedure for ACS?
Thanks.
C.K.

Here is a document which describes how to recover lost administrator credentials on the Cisco Secure Access Control Server Solution Engine.
http://www.cisco.com/en/US/products/sw/secursw/ps5338/products_password_recovery09186a00801ece5f.shtml

Default username and password for acs 3.2.3

Hi All
What is the default username and password to login to a newly built ACS Server V3.3.2 ?
Thanks in advanced.
Darren

Darren,
You need to log in to ACS on the console of the Windows server (assuming it's not an ACS Solution Engine). If you do that, http://localhost:2002 it should take you straight in with no username/password prompt. Once in you can setup admin users and access from other boxes.

Cisco 4682DBV username and password?

Hello dear friends, i would like to have access to my D3 CISCO 4682DBV unit's setup, but i don't know username and password when i try to connect to it via 192.168.100.1.
I tried leaving fields blank, admin:admin, blank:admin, admin:blank, admin:w2402 and every other password i could find on google. Please help.
Thanks in advance.

Judging by the message, it looks like you already configured your router? In that case, enter in the password and name for the wireless network that you gave the router when your frst configured it.
If you don't remember then you'll have to reset the router (hold the button for about 30seconds) and start from scratch. That will allow you to make up whatever settings you want. But remember to keep them in a safe place in case you ever need to refer to them again.
I don't work for Cisco. I'm just here to help.

Why is my Cisco ER admin page is blank after I place and enter the username and password?

when i enter my username and password in the CER admin login screen my page is blank. Can anyone tell me why? BTW I restarted Cisco Tomcat and my Cisco Emergency Responder will not start.

Version: 10.0.2.10000-11
Yes i did.
the platform page works just fine. It is just when i login with the admin page does not load.I mean it is just a blank white screen.
it should still appear without certificates. I have attached a screen shot

Configure a Cisco router with Username and Password.

Hello Guys,
Am quite new in cisco and i need to configure an 891 cisco router,can someone please show me step by step configuration commands for configuring Username and Secret Password.I would like the router to ask for "Username"and " Password" anytime i want to login the router through telnet.I also want to know if i have to erase the default configurations on the router first, before i start the configuration,and how it should be done in other not to loose the router whiles working on it.Thanks for your usual quick responds.
Regards,
Eben.

Hello Eben,
Peter has suggested to use SSH because of the fact that telnet data is sent in clear text, so someone with the right tools could easily find your password and your device could/would be compromised. It is security best practice. SSH is encrypted.
Technically speaking you do not need to change the hostname / domain name. But majority of Cisco documentation follow this method.
In case you are interested on how to do this without change... see below.
Router(config)#
Router(config)#crypto key generate rsa modulus 1024
% Please define a hostname other than Router.
Router(config)#crypto key generate rsa modulus 1024 label CISCO
The name for the keys will be: CISCO
% The key modulus size is 1024 bits
% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]
Router(config)#
*Jul 11 13:27:51.431: %SSH-5-ENABLED: SSH 1.99 has been enabled
Router(config)#
The normal cases just as shown in Cisco documentation, the parser (without a label on the crypto key) would force us to change the hostname, create a domain name. I think the domain name is there to put a label on the keys.
Router(config)#crypto key generate rsa general-keys modulus 1024
% Please define a hostname other than Router.
Router(config)#crypto key generate rsa
% Please define a hostname other than Router.
Router(config)#hos
Router(config)#hostname ISR
lexnetISR(config)#crypto key generate rsa general-keys modulus 1024
% Please define a domain-name first.
ISR(config)#ip domain name net.com
ISR(config)#exit
ISR(config)#crypto key generate rsa general-keys modulus 1024
The name for the keys will be: ISR.net.com
% The key modulus size is 1024 bits
% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]

[Maybe solved] Repeated prompts for username and password on HTTP(S)

I'm new to IOS but I'm taking ICND 1 and ICND 2 to catch up. I've gone as far as configuring a 3560 switch from "scratch" in a test environment, and am in part one of ICND 2.
Setting this switch up for HTTP administration, I've been prompted repeatedly for my username and password both when using a browser directly and when using Cisco Network Assistant (currently 5.5). This is different from the production switches I'm working with, that will prompt me once only and let me work. At first I suspected this was because I'm trying to use SSL and an in-house certitficate authority to sign the switch's certificate, but this is happening in plain HTTP as well. If I'm persistent enough, I eventually get the pages or configuration screens I want.
The difference between the production 3560s and my testing one, is the test one uses IOS 12.2(53), the current version. The production ones use 12.2(25)SEE3 through 12.2(35)SE5 and probably everything in between. I'm also experimenting with the releases that includes the web-based device manager on my test switch, but the behaviour is similar whether the image has the web-based manager or not.

In an update to this problem, I've reverted the switch I've been testing back to 12.2(35)SE5, which is what the majority of my production 3560s use. It appears to behave in the same fashion: Repeatedly asking for credentials over HTTP(S).
While my non-production switch has a local user database set up, my production switches use two ACS servers. The relevant bits of the running config are:
aaa new-model
aaa group server tacacs+ mcbhtacacs
server 10.1.2.221
server 10.1.2.222
aaa group server radius mcbhradius
server 10.1.2.221 auth-port 1645 acct-port 1646
server 10.1.2.222 auth-port 1645 acct-port 1646
aaa authentication login default group mcbhtacacs local
aaa authentication login LOCALAUTH local
aaa authorization exec default group mcbhtacacs
aaa accounting send stop-record authentication failure
aaa accounting exec default start-stop group mcbhtacacs
aaa accounting commands 1 default start-stop group mcbhtacacs
aaa accounting commands 15 default start-stop group mcbhtacacs
aaa accounting system default start-stop group mcbhtacacs
aaa session-id common
tacacs-server host 10.1.2.221 key 7 [censored]
tacacs-server host 10.1.2.222 key 7 [censored]
tacacs-server directed-request
radius-server host 10.1.2.221 auth-port 1645 acct-port 1646 key 7 [censored]
radius-server host 10.1.2.222 auth-port 1645 acct-port 1646 key 7 [censored]
radius-server source-ports 1645-1646
Another switch that does work without repeated prompting has these relevant bits:
aaa new-model
aaa group server tacacs+ mcbhtacacs
server 10.1.2.221
server 10.1.2.222
aaa group server radius mcbhradius
server 10.1.2.221 auth-port 1645 acct-port 1646
server 10.1.2.222 auth-port 1645 acct-port 1646
aaa authentication login default group mcbhtacacs local
aaa authentication login LOCALAUTH local
aaa authorization exec default group mcbhtacacs local
aaa accounting send stop-record authentication failure
aaa accounting exec default start-stop group mcbhtacacs
aaa accounting commands 1 default start-stop group mcbhtacacs
aaa accounting commands 15 default start-stop group mcbhtacacs
aaa accounting system default start-stop group mcbhtacacs
aaa session-id common
tacacs-server host 10.1.2.221 key 7 [censored]
tacacs-server host 10.1.2.222 key 7 [censored[
tacacs-server directed-request
radius-server host 10.1.2.221 auth-port 1645 acct-port 1646 key 7 [censored]
radius-server host 10.1.2.222 auth-port 1645 acct-port 1646 key 7 [censored]
radius-server source-ports 1645-1646
10.1.2.221 and 10.1.2.222 are the ACS servers, running ACS 4.1 and are linked to a pair of Active Directory domain controllers.
Aside from host names, these two switches appear to have an identical AAA configuration. So why would the first switch repeatedly ask for credentials over HTTP when the second switch with the same software does not?

Reseting SSH username and password

Hi,
I have configured Cisco Secure ACS (Version: 5.3.0.40.6).I am able to login with web access.
I forgot my ssh credential, Can any one tell me how to reset ssh username and password?
Or how can we configure through web access?
Thanx
Arjun

jasonwryan wrote:...and then wait to get hacked.
Sure, but this wasn't the point .
jasonwryan wrote:Seriously, set up public key authentication: it is simple and works like a charm on Android.
100% ACK.
Last edited by Tarqi (2014-03-27 01:58:36)

I have a request from a customer to run a script to create multiple Usernames and Passwords on ACS5.3 appliance.

I have a request from a cutomer to run a script to create multiple username and password on ACS5.3 Appliance. Does anyone has any suggestion on how to go about this?

Have you tried using the import option on the ACS? You can put all your accounts in a csv file and upload it into the ASA.
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/users_id_stores.html#wp1132152
If that doesnt work you can use the REST Web Services in ACS also:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/sdk/rest.html
Thanks,
Tarik Admani
*Please rate helpful posts*

Why do my firewalls only use the domain username and password for login and enable passwords, not a different enable password like my switches do? The RADIUS config looks the same...

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Issue:
Cisco firewalls require only one level of password i.e. the domain username and password are used for both logging in as well as reaching global configuration mode.
Background:
We have multiple Cisco network devices set up which authenticate to our Windows domain controller using NPS (Windows 2008 R2). The switches we have set up all function exactly as we would hope as they require your domain username and password to login to the device. They then require a separate password when you use the enable command, this is stored in Active Directory:
Switches:
Username:domain-username
Password:domain-password
SWITCH>enable
Password:enable-password-in-Active-Directory
SWITCH#
Firewalls (as they currently are):
Username:domain-username
Password:domain-password
FIREWALL>enable
Password:domain-password
FIREWALL #
With the firewalls however, they require your domain username and password first, and then your domain password again when using the enable command. I want the firewalls to use the enable level password that the switches currently use instead of the domain password again. The current configuration look like the following:
Current switch configuration:
aaa new-model
aaa authentication login default group radius local
aaa authentication enable default group radius enable
aaa authorization exec default group radius local
aaa session-id common
radius-server host 192.168.0.1 auth-port 1645 acct-port 1646
radius-server source-ports 1645-1646
radius-server key 7 1234abcd
Current firewall configuration:
aaa-server DC01 protocol radius
aaa-server DC01 (outside) host 192.168.0.1
aaa authentication ssh console DC01 LOCAL
aaa authentication enable console DC01 LOCAL
key 1234abcd
Any help would be great, thanks!

Cisco ASA works that way by design. You could remove "aaa authentication enable" and then you could use the "enable password" command to set your enable password.
But if you do that, then ASA would change your username to "enable_15". That would break Authorization and Accounting if you're using them. Let me clarify with an example
Firewalls :
Username:domain-username
Password:domain-password
FIREWALL>show curpriv
Username : domain-username
Current privilege level : 1
Current Mode/s : P_UNPR
FIREWALL>enable
Password:enable-password-from-running-config
FIREWALL #show curpriv
Username : enable_15
Current privilege level : 15
Current Mode/s : P_PRIV
If you're using Authorization and Accounting it's recommended to stick with your current behavior.

ASA 5505 Username and Password

Hi All,
I am trying to configure an ASA 5505 with a username and password. I set all the pass words:
password xxxxxxx
enable password xxxxxxx
username xxxxxx password xxxxxxx
When I reload the device it prompts me for the username, then the password and it fails and just asks for the username again. I have even tried to delete the username/password combo but it still prompts me for it. When I do password recovery the confreg is 0x00000001. I am no ASA expert and this is getting a bit frustrating.
When I first configured the device and reloaded it, everything worked fine.....once. Upon the second reload it just keeps prompting me.
Thanks for any help.
Bill

Hello Carter,
Hmm, it sounds like a config-register problem.
So when you are in rommon you got to set the confreg to be on 0x41 so you can ignore the startup-config.
Then when you enter to the ASA please do the following:
enable password cisco
username password cisco
config-register 0x01
wr
and then finally reload,
Regards,
Julio

E1200 modem: Username and Password don't work! help!

We cannot allow other devices (computers etc) on our network. the only one allowed is the one thats set up the network originally. I've contacted our internet provider, spyware and everyone else and they say its within the router. And the username and password on the laptop do not allow us in. Other devices say "authentication problem" or they are just not capable of getting onto the Wifi/Network. So, within our wireless network settings/properties we've gotten the name and pass key for going into our modem via the web...but it does not work. Need help with the username and password, the one we were given does not work......help? also, we do not have phone service where we live so calling and being on the computer is not possible....any email or forum step by step is the only capability. Thank you!

Hello kreardon410,
Try to check if you have the Cisco Connect Software installed on one of the computers. Router's default log in is admin for the password and just leave the username blank. If you won't be able to access it still, you may reset and configure the router again.
Help, learn and share

WLC 4402 username and password expires automatically

Hi,
We are facing issue with Cisco WLC 4402 (Cisco AireOS Version 4.2.205.0) and username and password expired automatically. It happens very often. We are not able to retreive the password, so everytime we need to reset(factory default) the Cisco WLC4402 and doing fresh installation.
Whether it is the hardware issue or software bug.
Also is there any possibility of recover the username and [password with resetting the cisco wlc4402.
Kindly suggest on this issue.
Regards
S.Manikandan

Hmmm.. Strange!! are we using any TACACS to manage?? or just the management username and password??
I guess after 5.2 WLC code or so we have the option of resetting the password without losing the config!!
Regards
Surendra

Aironet 1100 Default Username and Password not working

I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck. any help would be appreciated.
I also have a Cisco Aironet AP1242AG that is doing the same thing.

Hi Rich,
I assume that you are using the mode button to reset the configurations on these units -- this procedure *should* reset all credentials to Cisco.
If this is still not working, you can try the following:
1) Connect console port and power-cycle unit
2) When IOS starts loading, hit ESC key twice to get to the boot-loader prompt
3) At the boot-loader prompt show a directory of the flash filesystem (dir flash:)
4) Delete or rename the files "config.txt" and "env_vars", then boot the system ("delete flash:/config.txt" "delete flash:/env_vars")
-Patrick Croak
Wireless TAC

Cisco ACS 5.5 username and password

Similar Messages

Maybe you are looking for