Cisco AIR-CAP1602I-E-K9 Telnet issue
Hi Team, I have installed new cisco AIR-CAP1602I-E-K9 in the remote site LAN however the access point received the ip address through central DHCP helper address. I am able to ping the access point through LAN but I am unable to telenet the device to configure.
Also when Field enginner visited on site to connect physical he connected through console but we were not able get into configure mode though we had full privilege access.
Please advice.
AP0006.f618.26f5#sh version
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP0006.f618.26f5 uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FGL1703ZA3E
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:06:F6:18:26:F5
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC164971SY
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1703ZA3E
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xF
Thanks,
1. Does it mean I should not be able to telnet also into the AP though I can ping from Router LAN ( AP is connected directly to router ethernet interface).
2. I am also not able to discover controller when running in controller-based IOS. getting below errors.
Thanks to advice on above points.
Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
AP0006.f618.26f5#
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.1
AP0006.f618.26f5#1.13
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
Not in Bound state.
*Mar 1 00:03:49.505: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:53.393: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:03:53.477: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.93.22, mask 255.255.255.128, hostname AP0006.f618.26f5
en
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.50.1.235) (10.50.1.236)
*Mar 1 00:04:00.505: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:04:00.565: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
Not in Bound state.
*Mar 1 00:04:46.069: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:04:49.161: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:04:49.273: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.115.20, mask 255.255.255.128, hostname AP0006.f618.26f5
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.50.1.235)
*Mar 1 00:04:57.069: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP. (10.50.1.236)
*Mar 1 00:05:15.068: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
Not in Bound state.
*Mar 1 00:06:00.568: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:06:04.396: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:06:04.412: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.93.22, mask 255.255.255.128, hostname AP0006.f618.26f5
en
AP0006.f618.26f5#
AP0006.f618.26f5#sh
Writing out the event log to flash:/event.log ...
ip int
*Mar 1 00:06:11.668: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Could not discover WLC using DHCP IP address, Reload to use static IP.
Similar Messages
-
IMP: Cisco AIR-CAP1602 &1532 not joining 2504 Controller issue
Dear Team, We have Cisco wireless implementation in clients premises. We have 8 indoor AP (AIR-CAP1602E-AK9) and 2 Outdoor AP (AIR-CAP1532I-AK9) . Seven indoor APs are able to join the 2504 controller, but 1 indoor AIR-CAP1602E AP is not joining and signal is RED continuously while as outdoor AP AIR-CAP1532I-AK9 signal goes blinking from green, red to amber continuously and is not downloading LWAPP image from the controller even after hard reset.
The output for both APs shown below-
1) AIR-CAP1602E-A-K9:
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvara
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
Boot from flash
IOS Bootloader - Starting system.
FLASH CHIP: Spansion S25FL256
Xmodem file system is available.
flashfs[0]: 14 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 418304
flashfs[0]: Bytes available: 31517696
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 18:e7:28:d1:9b:05
************* loopback_mode = 0
The system is unable to boot automatically because there
are no bootable files.
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvarag
Same event repeating, failed to reset and reboot device
2) AIR_CAP1532I-A-K9 (Outdoor AP):
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_47:32:e4'running version 7.5.102.0 is rejected.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 100.1.1.20
signal goes blinking from Grean, Red to Amber continuously.
Failed to download LWAPP image from the controller even after hard reset.
Default image: 7.6.95.12
Logs and screen shot attached
Please advice.
Thanks
AakashHi please note the details below-
AIR-CAP1602E-A-K9:
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvara
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
Boot from flash
IOS Bootloader - Starting system.
FLASH CHIP: Spansion S25FL256
Xmodem file system is available.
flashfs[0]: 14 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 418304
flashfs[0]: Bytes available: 31517696
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 18:e7:28:d1:9b:05
************* loopback_mode = 0
The system is unable to boot automatically because there
is no bootable files.
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvarag
Can't reboot device!
WLC-SYSLOG
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.5.102.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_47:32:e4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 100.1.1.20
Last Reset....................................... Power on reset
System Up Time................................... 0 days 2 hrs 18 mins 39 secs
System Timezone Location......................... (GMT -6:00) Central Time (US a nd Canada)
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +32 C
External Temperature............................. +37 C
Fan Status....................................... 4000 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:47:32:E0
Maximum number of APs supported.................. 15 -
WLC5508 problem connect AIR-CAP1602I-R-K9
Добрый день,
Точка Air-cap1602 не может подключиться к контроллеру,
В чем может быть проблема?
Спасибо.
AP885a.92bb.97ab#sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-R-K9 , VID: V01, SN: FGL1744W6WG
AP885a.92bb.97ab# sh version
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 29-Jul-13 12:35 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP885a.92bb.97ab uptime is 2 hours, 58 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-2.JB2/ap1g2-k9w8-mx.152-2.JB2"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-R-K9 (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.
Processor board ID FGL1744W6WG
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 88:5A:92:BB:97:AB
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17432XWL
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1744W6WG
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-R-K9
Configuration register is 0xF
(Cisco Controller) >show inventory
Burned-in MAC Address............................ C0:67:AF:1A:CF:A0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 12
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V03, SN: FCW1748L07P
(Cisco Controller) >show inventory
Burned-in MAC Address............................ C0:67:AF:1A:CF:A0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 12
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V03, SN: FCW1748L07P
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS + LDPE
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.0.66
Last Reset....................................... Software reset
System Up Time................................... 0 days 23 hrs 37 mins 52 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +42 C
External Temperature............................. +22 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ C0:67:AF:1A:CF:A0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 12
(Cisco Controller) >*spamApTask7: Jan 30 16:43:11.448: 64:e9:50:af:66:70 Discarding non-ClientHello Handshake OR DTLS encrypted packet from 10.103.24.11:47484)since DTLS session is not established
*spamApTask6: Jan 30 16:43:11.556: 64:e9:50:af:66:70 Discovery Request from 10.103.24.11:47483
*spamApTask6: Jan 30 16:43:11.556: 64:e9:50:af:66:70 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 12, joined Aps =0
*spamApTask6: Jan 30 16:43:11.557: 64:e9:50:af:66:70 Discovery Response sent to 10.103.24.11:47483
*spamApTask6: Jan 30 16:43:11.557: 64:e9:50:af:66:70 Discovery Response sent to 10.103.24.11:47483
*spamApTask6: Jan 30 16:43:21.552: 64:e9:50:af:66:70 DTLS connection not found, creating new connection for 10:103:24:11 (47483) 10:1:0:66 (5246)
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: called to evaluate <cscoDefaultIdCert>
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: called to get cert for CID 1301e815
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCertFromCID: comparing to row 2, certname >cscoDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: called to evaluate <cscoDefaultIdCert>
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetSshPrivateKeyFromCID: called to get key for CID 1301e815
*spamApTask6: Jan 30 16:43:21.553: sshpmGetSshPrivateKeyFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetSshPrivateKeyFromCID: comparing to row 1, certname >bsnDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetSshPrivateKeyFromCID: comparing to row 2, certname >cscoDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.553: sshpmGetSshPrivateKeyFromCID: match in row 2
*spamApTask6: Jan 30 16:43:21.879: sshpmGetIssuerHandles: locking ca cert table
*spamApTask6: Jan 30 16:43:21.879: sshpmGetIssuerHandles: calling x509_alloc() for user cert
*spamApTask6: Jan 30 16:43:21.879: sshpmGetIssuerHandles: calling x509_decode()
*spamApTask6: Jan 30 16:43:21.883: sshpmGetIssuerHandles: <subject> C=US, ST=California, L=San Jose, O=Cisco Systems, CN=AP1G2-885a92bb97ab, [email protected]
*spamApTask6: Jan 30 16:43:21.883: sshpmGetIssuerHandles: <issuer> O=Cisco Systems, CN=Cisco Manufacturing CA
*spamApTask6: Jan 30 16:43:21.883: sshpmGetIssuerHandles: Mac Address in subject is 88:5a:92:bb:97:ab
*spamApTask6: Jan 30 16:43:21.883: sshpmGetIssuerHandles: Cert Name in subject is AP1G2-885a92bb97ab
*spamApTask6: Jan 30 16:43:21.883: sshpmGetIssuerHandles: Cert is issued by Cisco Systems.
*spamApTask6: Jan 30 16:43:21.883: sshpmGetCID: called to evaluate <cscoDefaultMfgCaCert>
*spamApTask6: Jan 30 16:43:21.883: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.883: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCertFromCID: called to get cert for CID 2b59913d
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
*spamApTask6: Jan 30 16:43:21.884: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
*spamApTask6: Jan 30 16:43:21.884: ssphmUserCertVerify: calling x509_decode()
*spamApTask6: Jan 30 16:43:21.894: ssphmUserCertVerify: user cert verfied using >cscoDefaultMfgCaCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetIssuerHandles: ValidityString (current): 2014/01/30/16:43:21
*spamApTask6: Jan 30 16:43:21.894: sshpmGetIssuerHandles: ValidityString (NotBefore): 2013/10/29/01:36:25
*spamApTask6: Jan 30 16:43:21.894: sshpmGetIssuerHandles: ValidityString (NotAfter): 2023/10/29/01:46:25
*spamApTask6: Jan 30 16:43:21.894: sshpmGetIssuerHandles: getting cisco ID cert handle...
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: called to evaluate <cscoDefaultIdCert>
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.894: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
*spamApTask6: Jan 30 16:43:21.902: sshpmFreePublicKeyHandle: called with 0x2c20d0e4
*spamApTask6: Jan 30 16:43:21.902: sshpmFreePublicKeyHandle: freeing public key
*spamApTask6: Jan 30 16:43:22.089: 64:e9:50:af:66:70 Allocated index from main list, Index: 441
*spamApTask6: Jan 30 16:43:22.089: 64:e9:50:af:66:70 DTLS keys for Control Plane are plumbed successfully for AP 10.103.24.11. Index 442
*spamApTask6: Jan 30 16:43:22.089: 64:e9:50:af:66:70 DTLS Session established server (10.1.0.66:5246), client (10.103.24.11:47483)
*spamApTask6: Jan 30 16:43:22.089: 64:e9:50:af:66:70 Starting wait join timer for AP: 10.103.24.11:47483
*spamApTask6: Jan 30 16:43:22.091: 64:e9:50:af:66:70 Join Request from 10.103.24.11:47483
*spamApTask6: Jan 30 16:43:22.092: 64:e9:50:af:66:70 Deleting AP entry 10.103.24.11:47483 from temporary database.
*spamApTask6: Jan 30 16:43:22.092: 64:e9:50:af:66:70 Join Version: = 117730816
*spamApTask6: Jan 30 16:43:22.093: 64:e9:50:af:66:70 Join resp: CAPWAP Maximum Msg element len = 100
*spamApTask6: Jan 30 16:43:22.093: 64:e9:50:af:66:70 Join Response sent to 10.103.24.11:47483
*spamApTask6: Jan 30 16:43:22.093: 64:e9:50:af:66:70 CAPWAP State: Join
*spamApTask6: Jan 30 16:43:22.093: 64:e9:50:af:66:70 capwap_ac_platform.c:1225 - Operation State 0 ===> 4
*apfReceiveTask: Jan 30 16:43:22.094: 64:e9:50:af:66:70 Register LWAPP event for AP 64:e9:50:af:66:70 slot 0
*apfReceiveTask: Jan 30 16:43:22.095: 64:e9:50:af:66:70 Register LWAPP event for AP 64:e9:50:af:66:70 slot 1
*spamApTask6: Jan 30 16:43:22.226: 64:e9:50:af:66:70 Configuration Status from 10.103.24.11:47483
*spamApTask6: Jan 30 16:43:22.226: 64:e9:50:af:66:70 CAPWAP State: Configure
*spamApTask6: Jan 30 16:43:22.226: 64:e9:50:af:66:70 Updating IP info for AP 64:e9:50:af:66:70 -- static 1, 10.1.0.67/255.255.255.0, gtw 10.1.0.128
*spamApTask6: Jan 30 16:43:22.227: 64:e9:50:af:66:70 Configured Static IP Address not valid for AP 64:e9:50:af:66:70
*spamApTask6: Jan 30 16:43:22.227: 64:e9:50:af:66:70 Updated IP Domain info for AP 64:e9:50:af:66:70 -- set 0, Domain
*spamApTask6: Jan 30 16:43:22.227: 64:e9:50:af:66:70 Updating IP NamServer info for AP 64:e9:50:af:66:70 -- set 0, nameserver 0.0.0.0
*spamApTask6: Jan 30 16:43:22.227: 64:e9:50:af:66:70 AP 64:e9:50:af:66:70: Invalid country code ().
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 PHY_TX_POWER_PAYLOAD: Invalid Tx Power Level 0
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 Channel 13 is invalid in the domain
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 AP 64:e9:50:af:66:70: Invalid country code ().
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 PHY_TX_POWER_PAYLOAD: Invalid Tx Power Level 0
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 Channel 161 is invalid in the domain
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 Setting MTU to 1485
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 AP 64:e9:50:af:66:70: Invalid country code ().
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 Regulatory Domain Mismatch: AP 64:e9:50:af:66:70 not allowed to join. Regulatory Domain check failed.
Allow
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 Finding DTLS connection to delete for AP (10:103:24:11/47483)
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 Disconnecting DTLS Capwap-Ctrl session 0x1702d4a0 for AP (10:103:24:11/47483)
*spamApTask6: Jan 30 16:43:22.228: 64:e9:50:af:66:70 CAPWAP State: Dtls tear down
*spamApTask6: Jan 30 16:43:22.229: 64:e9:50:af:66:70 DTLS keys for Control Plane deleted successfully for AP 10.103.24.11
*spamApTask6: Jan 30 16:43:22.236: 64:e9:50:af:66:70 Failed post decode processing of config status from 10.103.24.11:47483
*spamApTask6: Jan 30 16:43:22.236: 64:e9:50:af:66:70 State machine handler: Failed to process msg type = 5 state = 5 from 10.103.24.11:47483
AP885a.92bb.97ab#
*Jan 30 17:00:47.163: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jan 30 17:00:53.087: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 30 17:00:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.66 peer_port: 5246
*Jan 30 17:00:53.539: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.66 peer_port: 5246
*Jan 30 17:00:53.539: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.66
*Jan 30 17:00:53.539: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Jan 30 17:00:53.539: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Jan 30 17:00:53.539: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Jan 30 17:00:53.539: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.66
., 1)30 17:01:11.671: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(UNKNOWN_MESSAGE_TYPE (5)
*Jan 30 17:01:11.671: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jan 30 17:01:11.671: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.1.0.66:5246
*Jan 30 17:01:11.715: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jan 30 17:01:11.735: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jan 30 17:01:11.735: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jan 30 17:01:11.747: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jan 30 17:01:11.779: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jan 30 17:01:12.735: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jan 30 17:01:12.783: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Jan 30 17:01:12.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jan 30 17:01:13.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jan 30 17:01:13.783: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jan 30 17:01:13.811: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jan 30 17:01:13.819: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jan 30 17:01:13.827: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jan 30 17:01:14.811: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jan 30 17:01:14.819: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jan 30 17:01:14.855: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jan 30 17:01:15.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to upHI ,
PID: AIR-CAP1602I-R-K9 , VID: V01, SN: FGL1744W6WG(Cisco Controller) >show sysinfoManufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco ControllerProduct Version.................................. 7.4.110.0Bootloader Version............................... 1.0.1Field Recovery Image Version..................... 6.0.182.0Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2Build Type....................................... DATA + WPS + LDPESystem Name...................................... CISCO-CAPWAP-CONTROLLERSystem Location.................................. System Contact................................... System ObjectID.................................. 1.3.6.1.4.1.9.1.1069Redundancy Mode.................................. DisabledIP Address....................................... 10.1.0.66Last Reset....................................... Software resetSystem Up Time................................... 0 days 23 hrs 37 mins 52 secsSystem Timezone Location......................... System Stats Realtime Interval................... 5System Stats Normal Interval..................... 180Configured Country............................... US - United States
you ahve a wrong regulatery domain on AP.
If you are in USA then the access point should be AIR-CAP1602I-A-K9
Which country are you in ??
Regards -
AIR-CAP1602I-E-K9 Not Talking to WLC 5508
hi all,
can't seem to get my APs to talk to WLC 5508.
can someone advise which WLC firmware to use and where can i get/download (link pls).
currently WLC is running 6.0.199.4.
Mar 1 00:00:47.839: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inlin
e power source
*Mar 1 00:00:53.931: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:00:55.963: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 172.28.159.15, mask 255.255.255.192, hostname APfc99.47a3.4d22
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:06.899: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_f8
:72:64'running version 6.0.199.4 is rejected. <<<<
APfc99.47a3.4d22>sh ve
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
WARE (fc1)
APfc99.47a3.4d22 uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1726W6DQ
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: FC:99:47:A3:4D:22
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17182J4J
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1726W6DQ
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xFHi,
Date and time is ok on the WLC,
I configured Accept Self Signed Certificate (SSC) under Security / AP policy, once done the WLC recognized the AP, but output from the console of the AP power cycle the access point is:
IOS Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6551040
flashfs[0]: Bytes available: 25384960
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 4c:00:82:9a:47:a3
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...####################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Micronix MX25L256_35F
flashfs[2]: 5 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 6551040
flashfs[2]: Bytes available: 25256960
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
memory validate-checksum 30
^
% Invalid input detected at '^' marker.
no ip http server
^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
login authentication default
^
% Invalid input detected at '^' marker.
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Warning: the compile-time code checksum does not appear to be present.
cisco AIR-CAP1602I-N-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1730S57A
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 4C:00:82:9A:47:A3
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17284HL9
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1730S57A
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-N-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:13.683: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:14.687: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:15.123: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
*Mar 1 00:00:15.151: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:15.151: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Mar 1 00:00:16.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to uplwapp_crypto_init: MIC Present and Parsed Successfully
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact pe
rformance
*Mar 1 00:00:48.695: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_CONFIGU
RED_ON_SOURCE inline power source
*Mar 1 00:00:48.923: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 10.2.3.100, mask 255.255.255.0, hostname AP4c00.829a.47a3
Translating "CISCO-CAPWAP-CONTROLLER.campeche.ecosur.mx"...domain server (10.2.3
.10) [OK]
*Mar 1 00:00:59.915: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:00:59.919: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established. A0203E6, 147E, A020364, A47B, 0
*Mar 1 00:01:09.915: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:33:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:33:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
*Jan 29 09:34:17.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
2.3.230:5246
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 29 09:34:17.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Jan 29 09:34:28.015: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:34:28.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:34:33.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
and debug command output enable CAPWAP events
(Cisco Controller) >debug capwap events enable
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.092: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:08.093: 4c:00:82:9a:47:a0 DTLS keys for Control Plane deleted successfully for AP 10.2.3.100
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 DTLS connection closed event receivedserver (10.2.3.230/5246) client (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 Entry exists for AP (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 No AP entry exist in temporary database for 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.104: apModel:
*spamApTask7: Jan 29 03:39:08.104: apType = 38 apModel:
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Received LWAPP DISCOVERY REQUEST to 6c:41:6a:5f:95:2f on port '13'
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:18.104: 4c:00:82:9a:47:a3 DTLS connection not found, creating new connection for 10:2:3:100 (42107) 10:2:3:230 (5246)
*spamApTask7: Jan 29 03:39:18.638: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Allocated index from main list, Index: 397
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Using CipherSuite AES128-SHA
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS keys for Control Plane are plumbed successfully for AP 10.2.3.100. Index 398
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS Session established server (10.2.3.230:5246), client (10.2.3.100:42107)
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Starting wait join timer for AP: 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a0 Join Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a3 Deleting AP entry 10.2.3.100:42107 from temporary database.
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 MIC AP is not allowed to join by config
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 Join Request failed! -
Problem Joining AIR-CAP1602I-C-K9 with WLC 5508
Hi,
I am having trouble to get AIR CAP1602I-C-K9 attached to a 5508 WLC running code 7.4.110.0
Here is what I got from the AP logs:
====================================================================================================
Extracting files...
ap1g2-k9w8-mx.152-2.JB2/ (directory) 0 (bytes)
extracting ap1g2-k9w8-mx.152-2.JB2/K5.bin (75790 bytes)!!!!
*Dec 6 15:09:23.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 6 15:09:23.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.10.100 peer_port: 5246
*Dec 6 15:09:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.10.100
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: CAPWAP!
extracting ap1g2-k9w8-mx.152-2.JB2/ap1g2-k9w8-mx.152-2.JB2 (9202946 bytes)!!!!!!!!! SM handler: Failed to process message type 10 state 5.
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.16.10.100perform archive download capwap:/ap1g2 tar file
*Dec 6 15:09:23.583: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
*Dec 6 15:09:23.587: Loading file /ap1g2...
*Dec 6 15:09:24.007: %LINEPROTO-5-UPDOWN:!!!!!!!!!!! Line protocol on Interface Dot11Radio0, changed state to down
*Dec 6 15:09:24.063: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!!
*Dec 6 15:09:25.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!
*Dec 6 15:09:26.135: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Premature end of tar file
ERROR: Problem extracting files from archive.
Download image failed, notify controller!!! From:7.4.1.37 to 7.4.110.0, FailureCode:3
archive download: takes 63 seconds
*Dec 6 15:10:26.851: capwap_image_proc: problem extracting tar file
====================================================================================
after that the AP reboots and do same process over and over again,
Please help..
Many Thanks,
BarthHere is the info about AP and WLC:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... WLC1-AP
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 172.16.10.100
Last Reset....................................... Power on reset
System Up Time................................... 0 days 4 hrs 12 mins 28 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +44 C
External Temperature............................. +28 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ F8:72:EA:EF:2E:A0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, Power Off, Fan On
Maximum number of APs supported.................. 100
AP4403.a7fd.f040#sh ver
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:45 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP4403.a7fd.f040 uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-2.JB/ap1g2-k9w8-mx.152-2.JB"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-C-K9 (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.
Processor board ID FGL1711ZJNW
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:03:A7:FD:F0:40
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC16517DZ1
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1711ZJNW
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-C-K9
Configuration register is 0xF
AP4403.a7fd.f040#sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-C-K9 , VID: V01, SN: FGL1711ZJNW -
AIR-CAP1602i cannot join a WLC 5508 controller
Hello,
I'm managing a large number of access points on a Cisco wlc 5508 controller.
We've recently purchased a bunch of new AIR-CAP1602I-E-K9.
note that we already have AIR-CAP1602I-E-K9 and other models in production.
These A.P are not able to join the controller for some reason, I've tried a lot of different things but I am now at a loss.
I have checked the regulatory domain, upgraded the FUS, manually upgraded the software version of the LAP to match the version on the other A.P.
I even downgraded/upgraded the WLC code (version 7.4.x and 8.0)
I use the dhcp option 43 to to send the controller IP.
Here are the info that can help:
errors:
#on A.P
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
#on WLC
Lwapp join request rejected (WLC version 7.6.130.0)
Failed to add database entry (WLC version 8.0)
WLC sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... XXX
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... XXX
Last Reset....................................... Software reset
System Up Time................................... 6 days 4 hrs 16 mins 27 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... Multiple Countries:CA,FR
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +41 C
External Temperature............................. +22 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 7
Number of Active Clients......................... 1977
Burned-in MAC Address............................ A4:93:4C:B0:E4:C0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 250
AP sh version
AP58f3.9cb8.3701#sh version
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:56 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP58f3.9cb8.3701 uptime is 31 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-4.JB6/ap1g2-k9w8-mx.152-4.JB6"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 229366K/32768K bytes of memory.
Processor board ID FGL1832X5QU
PowerPC CPU at 533MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.100.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 58:F3:9C:B8:37:01
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC183171L4
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1832X5QU
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
AP sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-E-K9 , VID: V01, SN: FGL1832X5QU
Thanks for your help !Hi Olivier,
The error messages that you have on the debugs:
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
It is related to the bug: CSCuh46442
https://tools.cisco.com/bugsearch/bug/CSCuh46442/?referring_site=ss
This bug is resolved in version : 8.0.100.0
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn80.html#pgfId-1163951
Can you please paste here "show ap auth-list" from the controller CLI?
I suggest to enable MIC if it is not enabled, and then check if the AP's will join or not.
Kind Regards
Mohammad Setan -
01#Aironet 1600 (AIR-CAP1602i) & 3850 WLC (WS-C3850-24T-L)
Hi Friends
Trying to join 1602i (AIR-CAP1602i-E-k9) to 3850 (WS-C3850-24T) WLC but after join to WLC, the access point keeps rebooting
3850# Sho Version
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIV
ERSALK9-M), Version 03.03.03SE RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Sun 27-Apr-14 18:33 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.
(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: C3850 Boot Loader (C3850-HBOOT-M) Version 1.1, RELEASE SOFTWARE (P)
Ctrl1 uptime is 59 minutes
Uptime for this control processor is 1 hour, 1 minute
System returned to ROM by reload
System image file is "flash:packages.conf"
Last reload reason: reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: Ipbase
License Type: Permanent
Next reload license Level: Ipbase
cisco WS-C3850-24T (MIPS) processor with 4194304K bytes of physical memory.
Processor board ID FOC1729V00P
1 Virtual Ethernet interface
28 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
1609272K bytes of Flash at flash:.
0K bytes of Dummy USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : d0:c7:89:74:ef:00
Motherboard Assembly Number : 73-12238-06
Motherboard Serial Number : FOC17283XTY
Model Revision Number : B0
Motherboard Revision Number : D0
Model Number : WS-C3850-24T
System Serial Number : FOC1729V00P
Switch Ports Model SW Version SW Image Mode
* 1 32 WS-C3850-24T 03.03.03SE cat3k_caa-universalk9 INSTALL
Configuration register is 0x102
3850#show wireless mobility summary
Mobility Controller Summary:
Mobility Role : Mobility Controller
Mobility Protocol Port : 16666
Mobility Group Name : default
Mobility Oracle IP Address : 0.0.0.0
DTLS Mode : Enabled
Mobility Domain ID for 802.11r : 0xac34
Mobility Keepalive Interval : 10
Mobility Keepalive Count : 3
Mobility Control Message DSCP Value : 48
Mobility Domain Member Count : 1
Link Status is Control Link Status : Data Link Status
Controllers configured in the Mobility Domain:
IP Public IP Group Name Multicast IP Link Status
192.168.188.22 - default 0.0.0.0 UP : UP
3850#show wireless country configured
Configured Country.............................: AU - Australia
Configured Country Codes
AU - Australia : 802.11a Indoor,Outdoor/ 802.11b / 802.11g
1602i#show version
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(4)JB5h, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 16-Apr-14 00:32 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
WARE (fc1)
APc067.af86.55a3 uptime is 7 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-4.JB5h/ap1g2-k9w8-mx.152-4.JB5h"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 229366K/32768K by
tes of memory.
Processor board ID FGL1739W06Y
PowerPC CPU at 533MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 10.1.130.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C0:67:AF:86:55:A3
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17374QRS
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1739W06Y
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xF
3850# Show logging
Ctrl1#
*Jun 14 05:37:44.747: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:37:44.750: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:37:50.040: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:37:50.042: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:05.467: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:05.470: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:10.760: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:10.762: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:26.672: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:26.675: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:31.968: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:31.970: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:47.388: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:47.390: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:38:52.680: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:38:52.682: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:08.100: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:39:08.102: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:13.396: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:39:13.398: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:29.024: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:39:29.026: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:34.320: *%CAPWAP-3-ALREADY_IN_JOIN: 1 wcm: Dropping join request
from AP c025.5c96.90e0 - AP is already in joined state
*Jun 14 05:39:34.322: *%CAPWAP-3-DATA_TUNNEL_DELETE_ERR2: 1 wcm: Failed to dele
te CAPWAP data tunnel with interface id: 0x0 from internal database. Reason: AVL
database entry not found
*Jun 14 05:39:46.377: *%DTLS-3-HANDSHAKE_FAILURE: 1 wcm: Failed to complete DTL
S handshake with peer 192.168.188.25 for AP 0000.0000.0000Reason: sslv3 alert u
nexpected message
1602i# Show Logging
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:01.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:01:01.591: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Mar 1 00:01:02.011: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:02.247: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:08.315: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init:
MIC Present and Parsed Successfully
*Mar 1 00:01:09.075: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Mar 1 00:01:09.075: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
eset
*Mar 1 00:01:18.755: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:01:29.255: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:29.255: APAVC: Registering with CFT
APAVC: CFT registration of delete callback succeeded
APAVC: Reattaching Original Buffer pool for system use
Pool-ReAtach: paks 9355 radio8747
*Mar 1 00:01:36.415: %CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_ON_SO
URCE inline power source
*Mar 1 00:01:37.487: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:38.487: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
*Mar 1 00:01:38.543: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:39.206: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 14 05:47:22.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:22.335: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to up
*Jun 14 05:47:24.287: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:24.287: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:29.287: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:29.291: %DTLS-5-ALERT: Received WARNING : Close notify alert from
192.168.188.22
*Jun 14 05:47:29.291: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.188.22:5246
*Jun 14 05:47:29.291: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 14 05:47:22.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:22.291: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:22.291: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:27.291: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:27.295: %DTLS-5-ALERT: Received WARNING : Close notify alert from
192.168.188.22
*Jun 14 05:47:27.295: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.188.22:5246
*Jun 14 05:47:27.347: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Jun 14 05:47:27.375: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
dministratively down
*Jun 14 05:47:27.375: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to a
dministratively down
*Jun 14 05:47:27.379: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 14 05:47:27.431: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 14 05:47:28.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Jun 14 05:47:28.423: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to do
wn
*Jun 14 05:47:28.431: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
eset
*Jun 14 05:47:29.415: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
*Jun 14 05:47:29.423: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to down
*Jun 14 05:47:29.467: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 14 05:47:29.475: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to do
wn
*Jun 14 05:47:29.483: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Jun 14 05:47:30.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to up
*Jun 14 05:47:30.475: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Jun 14 05:47:30.519: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 14 05:47:31.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
*Jun 14 05:47:37.431: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 14 05:47:44.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:44.287: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.188.22 peer_port: 5246
*Jun 14 05:47:44.287: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:49.287: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 14 05:47:49.291: %DTLS-5-ALERT: Received WARNING : Close notify alert from
192.168.188.22
*Jun 14 05:47:49.291: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.188.22:5246Hi Leo
For product AIR-CAP1602I-E-K9 what country have to configured?
flowed this table: -
Can I configure Cisco 1602i (AIR-CAP1602I-T-K9) in Standalone mode ?
Hi everybody, please, i need some help here.
I bought 3 Cisco 1602i (AIR-CAP1602I-T-K9) but I didn't bought a Controller. How can I configure then in Standalone mode ?
I Saw in other forums, i need to change the IOS Software to an Autonomous Software. They suggested the ap1g2-k9w7-tar.152-4.JA1.tar. I would like to know if it is the right software and if there is any problem with licensing if i download and use it.
Explanation of the differences between AIR-CAP-1602i-x-K9 e AIR-SAP-1602i-x-K9
http://community.spiceworks.com/topic/448208-cisco-aironet-1602i-questions-issues
How to convert to IOS autonomous
http://www.experts-exchange.com/Networking/Wireless/Q_28245190.html
IOS Download:
http://software.cisco.com/download/release.html?mdfid=284366503&softwareid=280775090&release=15.2.4-JA1&flowid=37523
Thanks.
WesleyHi,
Yes you must need to change to autonomous mode.Yes it is the right software and you will not face any problem regarding license.
But for download the autonomous AP image from cisco you need a CCO (Cisco login) and valid service contract .
Here is the latest image:Can download from here
http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB5&relind=AVAILABLE&rellifecycle=ED&reltype=latest
How to covert from lAP to autonomous :
http://www.youtube.com/watch?v=QQ_NuxdRhQ4
http://rscciew.wordpress.com/2014/05/07/access-point-conversion-lap-to-aap-and-vice-versa/
Regards
Dont forget to rate helpful posts -
Cisco AIR-ANT2410YR 2.4 GHz 10dBi antenna issue
lahimakonem wrote:
The AP is powered by the Ethernet cable . do you think that's the issue?If the AP and antenna are both powered from the same port, double check the power consumption specs and be sure the switch is capable of supplying enough juice. You may need to run each device from its own PoE port... 2 cables instead of 1.Hello guys,
I have a cisco antena ( name above) connected to a 1600 cisco air AP. Im in a newer building, no reighforced concrete walls or anything and i cannot get a signal when im more than 15 feet away... Is there any setting i need to change?
Thank you
This topic first appeared in the Spiceworks Community -
Cisco AIR-LAP 1131 reboot in loop
Hi Everyone
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00CD9790 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000C3
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00CDB580 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x0184C8AA R17 = 0x0184C71B R18 = 0x00CDB760 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00CD9790
Frame 00: SP = 0x00CD97D0 PC = 0x0048A6A8
Frame 01: SP = 0x00CDB728 PC = 0x004361FC
Frame 02: SP = 0x00CDB740 PC = 0x0042E078
Frame 03: SP = 0x00CDB758 PC = 0x0044880C
Frame 04: SP = 0x00CDB798 PC = 0x0042A280
Frame 05: SP = 0x00CDB7C0 PC = 0x0042AA68
Frame 06: SP = 0x00000000 PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute,
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
And this is all it does, and keep loading the image. I already know the recovery procedure to reset it, but i wanted to know how i can put these AP in HREAP without having these issues. In the setup we need, we cannot have those AP be in local mode.
Thanks for any help and consideration .
RegardsHi Scott
Thanks for replying
here is the full output between loops :
Press RETURN to get started!
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
Translating "CISCO-LWAPP-CONTROLLER.aimfire.net"...domain server (10.1.10.100) [OK]
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed sta
15:52:12 UTC Fri Mar 1 2013: Unexpected exception to CPUvector 1100, PC = 0x5A9048 , LR = 0x48A8A0
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
CPU Register Context:
MSR = 0x00029230 CR = 0x53000035 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Writing crashinfo to flash:/crashinfo_20130301-155213
=== Flushing messages (15:52:20 UTC Fri Mar 1 2013) ===
Buffered messages:
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed state to UP
*Mar 1 15:52:11.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Queued messages:
*Mar 1 15:52:23.534: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Mar 1 15:52:11.414: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Nested exception_rom_monitor call (2 times)
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00D1EC18
Frame 00: SP = 0x00D1EC58 PC = 0x0048A6A8
Frame 01: SP = 0x00D20BB0 PC = 0x004361FC
Frame 02: SP = 0x00D20BC8 PC = 0x0042E078
Frame 03: SP = 0x00D20BE0 PC = 0x0044880C
Frame 04: SP = 0x00D20C20 PC = 0x0042A280
Frame 05: SP = 0x00D20C48 PC = 0x0042AA68
Frame 06: SP = 0x00000000 PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute, 7 seconds
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
flashfs[0]: 40 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 15129600
flashfs[0]: Bytes available: 869376
flashfs[0]: flashfs fsck took 41 seconds.
Base ethernet MAC Address: d8:67:d9:ba:9f:2e
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2"...###############################################
File "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
Image text-base: 0x00003000, data-base: 0x005AEE20
Initializing flashfs...
flashfs[1]: 40 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 15129600
flashfs[1]: Bytes available: 869376
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio 1 A506 7100 E8000000 A0000000 80000000 3
Radio 0 0 0 0 0 0 2
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from unknown reload cause - reason ptr 0xF, PC 0x5A9048, address 0x0
LWAPP image version 4.1.192.35
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: D8:67:D9:BA:9F:2E
Part Number : 73-13304-02
PCA Assembly Number : 800-36409-01
PCA Revision Number : B0
PCB Serial Number : FOC16304BZJ
Top Assembly Part Number : 800-29582-03
Top Assembly Serial Number : FTX1632N00D
Top Revision Number : A0
Product/Model Number : AIR-LAP1131G-A-K9
Press RETURN to get started!
Also , the switchport is a trunk port, i can definitely try it an access port . -
Is it possible to config AIR-CAP1602E-A-K9 without controller
I purchased a preowned AIR-CAP1602E-A-K9 to setup at my home. I did not realize it needed a controller, and need to set it up to work on it's own. Is it possible? any assistance would be greatly appreciated.
Hi Rendell,
AIR-CAP1602E-A-K9, its a controller based 802.11a/g/n.
This would need a controller to function.
I think u can try to change from Lightweigh to Autonomous and then u can use these APs.(I never used 1602E ap).
How to change Lightweight to Autonomous:
Please check these:
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
https://supportforums.cisco.com/docs/DOC-14960
http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
Regards
Dont forget to rate helpful posts. -
Hello to everyone. They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 18 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 15537664
flashfs[0]: Bytes available: 16331264
flashfs[0]: flashfs fsck took 23 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 00:27:0c:27:3f:00
Low Power PoE - enabling LAN Ethernet port only
Loading "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB"...###################################################################################################################################################################################################
File "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 18 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31352832
flashfs[1]: Bytes used: 15537664
flashfs[1]: Bytes available: 15815168
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio0 present A600 8000 A8020000 0 A8030000 30
Radio1 present A600 8000 B8020000 0 B8030000 13
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
%Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-LAP1522AG-E-K9 (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
Processor board ID FCW1346W00Q
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power loss
LWAPP image version 6.0.199.0
4 Gigabit Ethernet interfaces
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:27:0C:27:3F:00
Part Number : 73-10918-04
PCA Assembly Number : 800-28909-04
PCA Revision Number : A0
PCB Serial Number : FOC13430YBS
Top Assembly Part Number : 800-29338-04
Top Assembly Serial Number : FCW1346W00Q
Top Revision Number : F0
Product/Model Number : AIR-LAP1522AG-E-K9
% Please define a domain-name first.
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
Press RETURN to get started!
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:07.231: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.575: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:08.079: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:08.579: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:08.655: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1297 messages)
*Mar 1 00:00:08.683: AP identified to be in Huck Jr/1240/1130 configuration
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
*Mar 1 00:00:10.695: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
*Mar 1 00:00:10.695: %SNMP-5-COLDSTART: SNMP agent on host wifikal.Laiki-agora is undergoing a cold start
*Mar 1 00:00:10.759: Warning: Failed to run startup script
*Mar 1 00:00:10.771: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:12.771: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:18.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:20.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:22.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
*Mar 1 00:00:25.771: No Mesh startup file found
*Mar 1 00:00:29.763: Logging LWAPP message to 0.0.0.0.
*Mar 1 00:00:31.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:31.987: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:45.355: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED WS-C2960-8TC-L (0025.b413.b802)
*Mar 1 00:00:45.355: -Verify the required power-injector is installed on this port: WS-C2960-8TC-L(Fas 0/2).
*Mar 1 00:00:45.355: -If a power-injector is installed, issue the command:"power inline negotiation injector installed"
*Mar 1 00:01:26.015: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:01:34.515: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:01:36.515: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:01:37.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:39.563: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:03:05.575: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallback to DHCP.
*Mar 1 00:03:15.583: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:15.703: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 20.20.20.37, mask 255.255.255.0, hostname wifikal.Laiki-agora
*Mar 1 00:03:15.703: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
Translating "CISCO-CAPWAP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:20.751: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
Translating "CISCO-LWAPP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:21.759: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:03:21.815: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.TelestoHQ
*Mar 1 00:03:21.871: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.TelestoHQ
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 1 00:04:37.583: %MESH-6-LINK_UPDOWN: Mesh station 0027.0c27.3ffc link DownSearch this doc for "reset"
http://www.cisco.com/en/US/docs/wireless/technology/mesh/design/guide/MeshAP_52.html
Reset Button
The access point has a reset button located on the bottom of the unit (see Figure 3). The reset button is recessed in a small hole that is sealed with a screw and a rubber gasket. The reset button is used to perform these functions:
•Reset the access point—press the reset button for less than 10 seconds. LEDs turn off during the reset and then reactivate when the reset is complete.
•Disable battery backup power—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
–You can also disable the battery remotely by entering this command:
config mesh battery-state disable AP_name
•Switch off LEDS—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
Figure 3 Reset Button Location
1
Reset button location
Sent from Cisco Technical Support iPhone App -
I'm trying to deploy a WiFi solution for a client. It would consist of 2 SSIDs; one for internal users with internal network access and a guest with only internal access.
I have a Sonicwall TZ215:
External IP: x.x.x.x
LAN IP: 192.168.1.1/24
DHCP Server: 192.168.5-195/24
+++++++++++++++++++++++
Cisco SG500:
v1.3.0.62 / R750_NIK_1_3_647_260
CLI v1.0
set system mode switch queues-mode 4
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname xxx
ip ssh server
snmp-server location "xxx"
snmp-server contact "John Doe"
clock timezone CST 0 minutes 0
clock dhcp timezone
ip telnet server
interface vlan 1
ip address 192.168.1.2 255.255.255.0
no ip address dhcp
interface gigabitethernet1/1/1
switchport mode access
interface gigabitethernet1/1/2
switchport mode access
interface gigabitethernet1/1/3
switchport mode access
interface gigabitethernet1/1/4
switchport mode access
interface gigabitethernet1/1/5
switchport mode access
interface gigabitethernet1/1/6
switchport mode access
interface gigabitethernet1/1/7
switchport mode access
interface gigabitethernet1/1/8
switchport mode access
interface gigabitethernet1/1/9
switchport mode access
interface gigabitethernet1/1/10
switchport mode access
interface gigabitethernet1/1/11
switchport mode access
interface gigabitethernet1/1/12
switchport mode access
interface gigabitethernet1/1/13
switchport mode access
interface gigabitethernet1/1/14
switchport mode access
interface gigabitethernet1/1/15
switchport mode access
interface gigabitethernet1/1/16
switchport mode access
interface gigabitethernet1/1/17
switchport mode access
interface gigabitethernet1/1/18
switchport mode access
interface gigabitethernet1/1/19
switchport mode access
interface gigabitethernet1/1/20
switchport mode access
interface gigabitethernet1/1/21
switchport mode access
interface gigabitethernet1/1/22
switchport mode access
interface gigabitethernet1/1/23
switchport mode access
interface gigabitethernet1/1/24
switchport mode access
interface gigabitethernet1/1/25
switchport mode access
interface gigabitethernet1/1/26
switchport mode access
interface gigabitethernet1/1/27
switchport mode access
interface gigabitethernet1/1/28
switchport mode access
interface gigabitethernet1/1/29
switchport mode access
interface gigabitethernet1/1/30
switchport mode access
interface gigabitethernet1/1/31
switchport mode access
interface gigabitethernet1/1/32
switchport mode access
interface gigabitethernet1/1/33
switchport mode access
interface gigabitethernet1/1/34
switchport mode access
interface gigabitethernet1/1/35
switchport mode access
interface gigabitethernet1/1/36
switchport mode access
interface gigabitethernet1/1/37
switchport mode access
interface gigabitethernet1/1/38
switchport mode access
interface gigabitethernet1/1/39
switchport mode access
interface gigabitethernet1/1/40
switchport mode access
interface gigabitethernet1/1/41
switchport mode access
interface gigabitethernet1/1/42
switchport mode access
interface gigabitethernet1/1/43
switchport mode access
interface gigabitethernet1/1/44
switchport mode access
interface gigabitethernet1/1/45
switchport mode access
interface gigabitethernet1/1/46
switchport mode access
interface gigabitethernet1/1/47
switchport mode access
interface gigabitethernet1/1/48
switchport mode access
interface gigabitethernet1/1/51
switchport mode access
interface gigabitethernet1/1/52
switchport mode access
exit
macro auto disabled
ip default-gateway 192.168.1.1
encrypted
+++++++++++++++++++++++++++++++++++=
Cisco AIR-SAP2602I
! Last configuration change at 00:11:27 UTC Mon Mar 1 1993 by administrator
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXX
logging rate-limit console 9
enable secret 5 $1$RVFD$DybWHlNypzf3XsnL6RGND/
no aaa new-model
no ip routing
ip domain name XXX
dot11 syslog
dot11 vlan-name Guest_VLAN vlan 200
dot11 vlan-name Internal_Users vlan 300
dot11 vlan-name default vlan 1
dot11 ssid Internal
vlan 300
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 05180704241A18471802161B05
dot11 ssid Guest
vlan 200
authentication open
authentication key-management wpa
guest-mode
mbssid guest-mode
infrastructure-ssid optional
wpa-psk ascii 7 10652D4B5341151E09173E
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-2946962253
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2946962253
revocation-check none
rsakeypair TP-self-signed-2946962253
crypto pki certificate chain TP-self-signed-2946962253
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32393436 39363232 3533301E 170D3933 30333031 30303431
34325A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 39343639
36323235 3330819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
81009438 47D6CAB8 36B9260D D5FEFA7A DFA7E065 E47ECCA2 346674C6 54D9C004
D6D62585 DE26A41E 447E8607 D0BD58C5 92899510 4EEBF95C 9352D082 1BB71EBF
72D56DDC 87D55A85 4A242578 6BBD31AD E48C8354 1C7331BD 5ED9F29D 5F8B868E
14DB0C08 3930D2D4 3266ED2D 9902DAA4 A348B722 82FCC132 6FC4BF22 DC7B9DBC
2F010203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 149FB8D9 F772C9DE 4BC86DD9 451902F3 4994F7D8 E0301D06
03551D0E 04160414 9FB8D9F7 72C9DE4B C86DD945 1902F349 94F7D8E0 300D0609
2A864886 F70D0101 05050003 81810054 FBCE018A CC09679F 8CB2D20A C773DE00
51AFA13A AB5105D5 BAAB6F2F B7CAF46A 2BFDCDDC F156593F 16C509EF 8C5215C1
7631DEFA 9E16633C 1E89CE65 C56591B2 5BE90BD0 1941F0EA 5478924C 4C0E229D
013743C3 2D4993E0 C44F9143 89A7A5D6 870E3A6C A772B8BB D032956F 1A5B894A
40EC55B9 8C5E3876 7E4B45FE 3DD00B
quit
ip ssh version 1
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 100 mode ciphers aes-ccm
encryption vlan 200 mode ciphers aes-ccm
encryption vlan 300 mode ciphers aes-ccm
broadcast-key vlan 1 change 10000
broadcast-key vlan 100 change 10000
ssid Internal
ssid Guest
antenna gain 0
stbc
mbssid
station-role root
interface Dot11Radio0.200
encapsulation dot1Q 200 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.300
encapsulation dot1Q 300
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 300 mode ciphers aes-ccm
encryption vlan 200 mode ciphers aes-ccm
broadcast-key vlan 1 change 10000
antenna gain 0
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1
no ip route-cache
interface Dot11Radio1.200
encapsulation dot1Q 200 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.300
encapsulation dot1Q 300
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
hold-queue 160 in
interface GigabitEthernet0.1
encapsulation dot1Q 1
no ip route-cache
interface GigabitEthernet0.200
encapsulation dot1Q 200 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.300
encapsulation dot1Q 300
no ip route-cache
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
interface BVI1
ip address 192.168.1.10 255.255.255.0
no ip route-cache
ip default-gateway 192.168.1.1
no ip http server
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end
+++++++++++++++++++++++++++++++++++++++++
I was able to get dhcp from the Sonicwall with 192.168.1.0/24, but not from the SG500. I created a scope(192.168.2.0/24 for guest; 192.168.3.0/24 for internal users) I even created DHCP scope on the AP, but cannot get an IP from that either. I creatd an ACL to allow the 192.168.3.0/24 access elewhere, and denied 192.168.2.0 access to other but internet.
If I disabled all scopes on the Sonicwall, I get an APIPA from both AP/SG500. Any thoughts?What is your default VLAN?
On the AP, you configured VLAN 200 to be the native. is that the same with your othe devices?
"encapsulation dot1Q 200 native"
Regards,
Amjad
Rating useful replies is more useful than saying "Thank you" -
AIR-CAP1602E-N-K9 access point
hi,
can any one help me to configure AIR-CAP1602E-N-K9 as standalone acess point.
its a new one with default setting as per my knowledege its a controller based access point so pls help how to convert into standalone access point and which image is compatible with that.Converting a Lightweight Access Point Back to Autonomous Mode
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Note In some LWAPP deployments, the LWAPP controller resides between the access points and the rest of the network. In this topology, all traffic must cross over the controller before communication with network resources, such as a TFTP server, can occur. When converting back to non-LWAPP IOS with an access point that is no longer using the LWAPP protocol, traffic does not cross over the controller to reach the TFTP server.
Note The lightweight 1300 series access points can only be converted back to autonomous mode using a wireless LAN controller.
Using a Wireless LAN Controller to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode using a wireless LAN controller:
Step 1 Log into the CLI on the controller to which the access point is associated.
Step 2 Enter this command:
config ap tftp-downgrade tftp-server-ip-address filename access-point-name
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Set the timeout value on the TFTP server to 30 seconds.
Step 4 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.
Step 5 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 6 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 7 Disconnect power from the access point.
Step 8 Press and hold MODE while you reconnect power to the access point.
Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 10 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 11 After the access point reboots, reconfigure it using the GUI or the CLI. -
Can AIR-CAP1602i-x-k9 be converted to stand alone??
can air-cap1602i-x-k9 be converted to stand alone??
Yes , you can convert the AP to stanadlone by pushig the below image into the AP
http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB3a&relind=AVAILABLE&rellifecycle=ED&reltype=latest
You can use the below method to convert the same
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release
using a TFTP server: This method is for local conversion.
Step 1 The PC on which your TFTP server software runs must be configured with a static IP address in the range
of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a
1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200
series access point.
Step 4 Connect the PC to the access point using a Category 5 or better Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the
MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED
blinking green.
Thanks..
Maybe you are looking for
-
Window.open() & window.close () does not work in Portal application
Hello All, I am trying to open & close a popup window from a weblogic portal. But the following don't seem to work in this environment. As a web application, it works fine. <netui:anchor action="DetailedWorkObject" target="<script @lang ='java'> wind
-
How to customise "Sounds" in Mail??
Hello everyone... I have used Mac OS X for quite a long time but have never get around to using Mail until recently at the office... (Been using Entourage...) How do you customise "sounds" in Mail? i.e. Not only for 'New Incoming Mail' (which I saw,
-
I deleted my localstore, but save file dialog box is still maximized and unresizable
I had this error once before, and I was able to google a solution, but it was a long time ago and I Forget the solution, and since then the seo on this issue has become poluted with useless information :( I'm using firefox 17 but I don't think that m
-
Plz help me in running of server!!
Whenever i try to run tomcat server for the implementation of servlets it doesnot start. I have set the JAVA_HOME and TOMCAT_HOME path truely. i am using win2000 prof. the following message appears on the dos prompt when i execute it. D:\jakarta-tomc
-
Easy-webprint ex: toolbar not appearing despite being "ticked"
I run Windows 7 64 bit and use Internet Explorer 9. Printer is MG8250 Some weeks ago I downloaded Easy-webprint EX version 1.3.5.0 and it worked fine. I could get the toolbar to appear or disappear in the normal way ie via View/Toolbars then tickin