Cisco AIR-LAP 1522 PROBLEM

Hello to everyone. They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 18 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 15537664
flashfs[0]: Bytes available: 16331264
flashfs[0]: flashfs fsck took 23 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 00:27:0c:27:3f:00
Low Power PoE - enabling LAN Ethernet port only
Loading "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB"...###################################################################################################################################################################################################
File "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 18 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31352832
flashfs[1]: Bytes used: 15537664
flashfs[1]: Bytes available: 15815168
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio0 present A600 8000 A8020000 0 A8030000 30
Radio1 present A600 8000 B8020000 0 B8030000 13
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
%Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-LAP1522AG-E-K9   (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
Processor board ID FCW1346W00Q
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power loss
LWAPP image version 6.0.199.0
4 Gigabit Ethernet interfaces
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:27:0C:27:3F:00
Part Number                          : 73-10918-04
PCA Assembly Number                  : 800-28909-04
PCA Revision Number                  : A0
PCB Serial Number                    : FOC13430YBS
Top Assembly Part Number             : 800-29338-04
Top Assembly Serial Number           : FCW1346W00Q
Top Revision Number                  : F0
Product/Model Number                 : AIR-LAP1522AG-E-K9
% Please define a domain-name first.
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
Press RETURN to get started!
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:07.231: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.575: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:08.079: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:08.579: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:08.655: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1297 messages)
*Mar 1 00:00:08.683: AP identified to be in Huck Jr/1240/1130 configuration
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
*Mar 1 00:00:10.695: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
*Mar 1 00:00:10.695: %SNMP-5-COLDSTART: SNMP agent on host wifikal.Laiki-agora is undergoing a cold start
*Mar 1 00:00:10.759: Warning: Failed to run startup script
*Mar 1 00:00:10.771: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:12.771: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:18.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:20.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:22.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
*Mar 1 00:00:25.771: No Mesh startup file found
*Mar 1 00:00:29.763: Logging LWAPP message to 0.0.0.0.
*Mar 1 00:00:31.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:31.987: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:45.355: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED WS-C2960-8TC-L (0025.b413.b802)
*Mar 1 00:00:45.355: -Verify the required power-injector is installed on this port: WS-C2960-8TC-L(Fas 0/2).
*Mar 1 00:00:45.355: -If a power-injector is installed, issue the command:"power inline negotiation injector installed"
*Mar 1 00:01:26.015: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:01:34.515: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:01:36.515: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:01:37.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:39.563: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:03:05.575: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallback to DHCP.
*Mar 1 00:03:15.583: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:15.703: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 20.20.20.37, mask 255.255.255.0, hostname wifikal.Laiki-agora
*Mar 1 00:03:15.703: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
Translating "CISCO-CAPWAP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:20.751: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
Translating "CISCO-LWAPP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:21.759: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:03:21.815: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.TelestoHQ
*Mar 1 00:03:21.871: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.TelestoHQ
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 1 00:04:37.583: %MESH-6-LINK_UPDOWN: Mesh station 0027.0c27.3ffc link Down

Search this doc for "reset"
http://www.cisco.com/en/US/docs/wireless/technology/mesh/design/guide/MeshAP_52.html
Reset Button
The access point has a reset button located on the bottom of the unit (see Figure 3). The reset button is recessed in a small hole that is sealed with a screw and a rubber gasket. The reset button is used to perform these functions:
•Reset the access point—press the reset button for less than 10 seconds. LEDs turn off during the reset and then reactivate when the reset is complete.
•Disable battery backup power—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
–You can also disable the battery remotely by entering this command:
config mesh battery-state disable AP_name
•Switch off LEDS—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
Figure 3 Reset Button Location
1
Reset button location
Sent from Cisco Technical Support iPhone App

Similar Messages

Cisco AIR-LAP 1131 reboot in loop

Hi Everyone
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00CD9790 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000C3
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00CDB580 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x0184C8AA R17 = 0x0184C71B R18 = 0x00CDB760 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00CD9790
Frame 00: SP = 0x00CD97D0    PC = 0x0048A6A8
Frame 01: SP = 0x00CDB728    PC = 0x004361FC
Frame 02: SP = 0x00CDB740    PC = 0x0042E078
Frame 03: SP = 0x00CDB758    PC = 0x0044880C
Frame 04: SP = 0x00CDB798    PC = 0x0042A280
Frame 05: SP = 0x00CDB7C0    PC = 0x0042AA68
Frame 06: SP = 0x00000000    PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute,
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
And this is all it does, and keep loading the image. I already know the recovery procedure to reset it, but i wanted to know how i can put these AP in HREAP without having these issues. In the setup we need, we cannot have those AP be in local mode.
Thanks for any help and consideration .
Regards

Hi Scott
Thanks for replying
here is the full output between loops :
Press RETURN to get started!
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
Translating "CISCO-LWAPP-CONTROLLER.aimfire.net"...domain server (10.1.10.100) [OK]
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed sta
15:52:12 UTC Fri Mar 1 2013: Unexpected exception to CPUvector 1100, PC = 0x5A9048 , LR = 0x48A8A0
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
CPU Register Context:
MSR = 0x00029230 CR = 0x53000035 CTR = 0x00000072 XER   = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3    = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7    = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11   = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15   = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19   = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23   = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27   = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31   = 0x00003D80
Writing crashinfo to flash:/crashinfo_20130301-155213
=== Flushing messages (15:52:20 UTC Fri Mar 1 2013) ===
Buffered messages:
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed state to UP
*Mar 1 15:52:11.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Queued messages:
*Mar 1 15:52:23.534: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Mar 1 15:52:11.414: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Nested exception_rom_monitor call (2 times)
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00D1EC18
Frame 00: SP = 0x00D1EC58    PC = 0x0048A6A8
Frame 01: SP = 0x00D20BB0    PC = 0x004361FC
Frame 02: SP = 0x00D20BC8    PC = 0x0042E078
Frame 03: SP = 0x00D20BE0    PC = 0x0044880C
Frame 04: SP = 0x00D20C20    PC = 0x0042A280
Frame 05: SP = 0x00D20C48    PC = 0x0042AA68
Frame 06: SP = 0x00000000    PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute, 7 seconds
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
flashfs[0]: 40 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 15129600
flashfs[0]: Bytes available: 869376
flashfs[0]: flashfs fsck took 41 seconds.
Base ethernet MAC Address: d8:67:d9:ba:9f:2e
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2"...###############################################
File "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
Image text-base: 0x00003000, data-base: 0x005AEE20
Initializing flashfs...
flashfs[1]: 40 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 15129600
flashfs[1]: Bytes available: 869376
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio 1 A506 7100 E8000000 A0000000 80000000 3
Radio 0 0 0 0 0 0 2
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from unknown reload cause - reason ptr 0xF, PC 0x5A9048, address 0x0
LWAPP image version 4.1.192.35
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: D8:67:D9:BA:9F:2E
Part Number                          : 73-13304-02
PCA Assembly Number                  : 800-36409-01
PCA Revision Number                  : B0
PCB Serial Number                    : FOC16304BZJ
Top Assembly Part Number             : 800-29582-03
Top Assembly Serial Number           : FTX1632N00D
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131G-A-K9
Press RETURN to get started!
Also , the switchport is a trunk port, i can definitely try it an access port .

Cisco AIR -LAP-1142 status led continuosly blinking green

hello all,
I have implemented around 46 access points (AIR-LAP-1142) in a customer site and i can see that the led of some of the access points are continously blinking green and no clients are associated to these access points. I have a WISM which has two controllers in it. I can see the particular aps to be joined in the controller. But my question is that why its not giving me any signal. Please help me as this is very urgent!!.. even if am under the access point the signal is not there. I checked the radio status of the aps and its up. The WLANs are activated from the controller also. Please help mee....!!

continously blinking green
This could mean that the AP hasn't joined the WiSM yet.
Can you console into the AP? If you can, reboot the AP and post the entire power up and bootup process and include the "sh logs".

Cisco Air LAP-1042 issue

Hi guys. I just purchase Cisco LAP-1042N for my office network expansion. When i console into the AP via serial. I am not able to used "configure terminal" command to set my AP name,static IP address.
I tried using "debug lwapp console cli" command it did not work. below is the capture screen of the error i am getting when assigning AP hostname. Error message : command is disable.
can some one guide me on how to configure the AP correctly and enable conf t command
Thanks in advanced.
Br
Syafiq

Is the AP new or used? It may have a configuration on it already if used - resest it to default and do the express setup as described here. I beleive the 1040 series needs a DHCP server per the following section from the configuraiton guide:
Default IP Address Behavior
When you connect a 1040, 1130AG, 1140, 1200, 1240, 1250, 1260, 2600 access point, or 1300 series access point/bridge with a default configuration to your LAN, the access point requests an IP address from your DHCP server and, if it does not receive an address, continues to send requests indefinitely.
As a Lightweight AP, most of its settings should come from the WLC once you have the LAP on the network where it can see the WLC.

Cisco Air-Lap1242AG

Hi i was trying to create a better stronger wireless network at my house. I picked up a Cisco Air-Lap1242AG on an auction thinking it would give me more range. Now trying to set it up i am trying to figure out if i made a mistake? Can this router be used at home with just a Cable Modem? Or does this need to hook into a Business Network?
Thanks
Eric

A Cisco "Air-LAP" access point is useless standalone by itself. It must participate on a network with a Cisco
Wireless Lan Controller appliance to configure and manage it.
And it's just an access point, not a router too, like a typical home unit is. Looks like you bought the wrong tool for the job.
In my opinion, the best performing consumer-grade wireless routers (for max range, and typical Internet surfing 802.11g speeds) I've ever encountered, for home use have been the old Buffalo Wireless-G High Power units, which I think you can still buy online these days.

Cisco LAP 1522

Sorry for this stupid question,
but is there anyway to access directly a LAP 1522 using a console port?
Best Regards.

Yes all the settings are as you suggested. Scott the problem is that it does not allow me to type anything. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 18 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 15537664
flashfs[0]: Bytes available: 16331264
flashfs[0]: flashfs fsck took 23 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 00:27:0c:27:3f:00
Low Power PoE - enabling LAN Ethernet port only
Loading "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB"...###################################################################################################################################################################################################
File "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 18 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31352832
flashfs[1]: Bytes used: 15537664
flashfs[1]: Bytes available: 15815168
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio0 present A600 8000 A8020000 0 A8030000 30
Radio1 present A600 8000 B8020000 0 B8030000 13
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
%Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-LAP1522AG-E-K9   (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
Processor board ID FCW1346W00Q
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power loss
LWAPP image version 6.0.199.0
4 Gigabit Ethernet interfaces
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:27:0C:27:3F:00
Part Number                          : 73-10918-04
PCA Assembly Number                  : 800-28909-04
PCA Revision Number                  : A0
PCB Serial Number                    : FOC13430YBS
Top Assembly Part Number             : 800-29338-04
Top Assembly Serial Number           : FCW1346W00Q
Top Revision Number                  : F0
Product/Model Number                 : AIR-LAP1522AG-E-K9
% Please define a domain-name first.
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
Press RETURN to get started!
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:07.231: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.575: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:08.079: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:08.579: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:08.655: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1297 messages)
*Mar 1 00:00:08.683: AP identified to be in Huck Jr/1240/1130 configuration
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
*Mar 1 00:00:10.695: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
*Mar 1 00:00:10.695: %SNMP-5-COLDSTART: SNMP agent on host wifikal.Laiki-agora is undergoing a cold start
*Mar 1 00:00:10.759: Warning: Failed to run startup script
*Mar 1 00:00:10.771: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:12.771: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:18.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:20.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:22.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
*Mar 1 00:00:25.771: No Mesh startup file found
*Mar 1 00:00:29.763: Logging LWAPP message to 0.0.0.0.
*Mar 1 00:00:31.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:31.987: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:45.355: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED WS-C2960-8TC-L (0025.b413.b802)
*Mar 1 00:00:45.355: -Verify the required power-injector is installed on this port: WS-C2960-8TC-L(Fas 0/2).
*Mar 1 00:00:45.355: -If a power-injector is installed, issue the command:"power inline negotiation injector installed"
*Mar 1 00:01:26.015: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:01:34.515: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:01:36.515: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:01:37.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:39.563: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:03:05.575: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallback to DHCP.
*Mar 1 00:03:15.583: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:15.703: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 20.20.20.37, mask 255.255.255.0, hostname wifikal.Laiki-agora
*Mar 1 00:03:15.703: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
Translating "CISCO-CAPWAP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:20.751: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
Translating "CISCO-LWAPP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:21.759: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:03:21.815: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.TelestoHQ
*Mar 1 00:03:21.871: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.TelestoHQ
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 1 00:04:37.583: %MESH-6-LINK_UPDOWN: Mesh station 0027.0c27.3ffc link Down

Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

hi,
I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives Ethernet LED = Off; Radio LED = RED ; Status LED = RED and only next listing in the screen:
Xmodem file system is available.
Flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error during initializion of the flash filesystem.
The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
ether_init
tftp_init
boot
When I type this commands, it doesn't help at all. The output will be following:
ap: flash_init
Initializing Flash...
flashfs[0]: out of memory
...done Initializing Flash.
ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ap: tftp_init
Unable to get our ip address: no "IP_ADDR" variable set
ap: boot
Loading ""...; permission denied
Error loading ""
Interrupt within 5 seconds to abort boot process.
Boot process failed...
ap:
what i do ? please help , thanks

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

Problem reseting Cisco AIR- LAP1131AG

Dear Expert,
we have customer which used Cisco Air-LAP1131AG and Wireless Lan Controller. The Controller went back to Cisco as Traid in, but we got some AP for our lab.
Problem is, that when you connect via Console cable it brings you into normal mode >, but when going into enable mode it asks for Password. Problem is, that customer changed password and don´t know anymore.
Is it possible to reset the password and configure the AP fresh from beginning?
Thanks
Klaus

and another one with 21 seconds
Press RETURN to get started!
*Mar 1 00:00:06.295: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:06.302: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
*Mar 1 00:00:07.236: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:08.236: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:20.136: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0 (not full duplex), with ROUTER_VOICE_LAB FastEthernet0/0 (full duplex).
*Mar 1 00:00:25.331: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:34.342: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 192.168.200.183, mask 255.255.255.0, hostname 24
24>
24>
24>ðXmodem file system is available.
flashfs[0]: 26 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7131136
flashfs[0]: Bytes available: 8867840
flashfs[0]: flashfs fsck took 32 seconds.
Base ethernet MAC Address: 00:1d:a1:ee:97:b4
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 10 mbps, half-duplex
Ethernet port 0 initialized: link is up
button pressed for 21 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
examining image...
%Error opening (connection timed out)Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
Image text-base: 0x00003000, data-base: 0x0035E440
Initializing flashfs...
flashfs[1]: 26 files, 9 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 7131136
flashfs[1]: Bytes available: 8867840
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ1147Q1KT
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1D:A1:EE:97:B4
Part Number                          : 73-8962-12
PCA Assembly Number                  : 800-24818-11
PCA Revision Number                  : B0
PCB Serial Number                    : FOC11443WRR
Top Assembly Part Number             : 800-29144-02
Top Assembly Serial Number           : FCZ1147Q1KT
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-E-K9
% Hostname contains one or more illegal characters.
Press RETURN to get started!
*Mar 1 00:00:06.294: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:06.302: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
*Mar 1 00:00:07.236: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:08.236: %LINEPROTO-5-UP
24>
24>DOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:09.820: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
24>
24>en
Password:

Cisco AIR-CAP26021-A-K9 || Error opening tftp:// ... /ap3g2-k9w7-tar.default

Hi everyone:
I have a problem with two Cisco AIR AP's ... I have configured already eight of them (in lightweight mode), but those two send me the next error, right now.
ap: %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)
And when I boot to the AP, it says:
%Error opening flash
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 11 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 15 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: c0:67:af:6f:31:25
Ethernet speed is 100 Mb - FULL Duplex
button is pressed, wait for button to be released...
button pressed for 21 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/ap3g2-k9w7-tar.default
examining image...
DPAA Set for Independent Mode
DPAA_INIT = 0x0
%Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)ap:
ap:
ap:
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 10 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 14 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: c0:67:af:6f:31:25
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...###########################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 10 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 7 seconds.
Base Ethernet MAC address: c0:67:af:6f:31:25
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x2003000
executing...
Initializing flashfs...
flashfs[2]: 10 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31739904
flashfs[2]: Bytes used: 7245824
flashfs[2]: Bytes available: 24494080
flashfs[2]: flashfs fsck took 8 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete.
Copying radio files from flash: to ram:
%Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
Uncompressing radio files...
File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
...done Initializing flashfs.
Press RETURN to get started!
*Mar 1 00:00:11.335: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:13.071: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.663: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:08 by prod_rel_team
*Mar 1 00:00:13.795: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:13.795: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
*Mar 1 00:00:13.799: %PARSER-4-BADCFG: Unexpected end of configuration file.
lwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:14.751: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:16.467: DPAA Initialization Complete
*Mar 1 00:00:16.467: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:16.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:47.151: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inline power source
*Mar 1 00:00:49.515: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.44.221, mask 255.255.255.0, hostname APc067.af6f.3125
Translating "CISCO-CAPWAP-CONTROLLER.asf.gob.mx"...domain server (10.1.1.2)
*Mar 1 00:01:00.403: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:00.451: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.asf.gob.mx
The thing is, I've been applying the instruction:
capwap ap controller ip address 10.4.13.2
'cause I want them to communicate with a remote controller, and the past eight did it fine, but this two didn't.
As for the things I've already tried, I have reset it's parameters to it's initial settings, I've tried to load a new IOS image, I've cleared the flash memory, but nothing works, it keeps communicating with the old controller.
How can I fix this? (I mean, changing or adapting the AP to a lightweight AP)
Thanks in advance

Its fine to try to apply it from the console...but if you really want to clear the AP, you need to clear the nvram. so if changing the primary from the GUI that the AP has joined didn't work, then try this:
debug capwap console cli
erase /all nvram
Example:
Entered the username and password
debug capwap console cli
erase /all nvram:
[confirm]
undebug all
reload
[confirm]
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red, what is this? it isn't in the manual

CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??

No cisco web is working perfectly.
do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
Autonomous AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
LAP AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
Regards

AIR-LAP-1142N-E-K9 unexpected power offs

Hi we have two seperate Cisco wireless networks both based around the same infrastructure.
Cisco 5508 WLC/s running 7.4.100 Firmware in our datacentre, with AIR-LAP-1142N-E-K9 LAPS distributed at site offices.
This infrastructure has been running well until recently when we have had a spate of the LAPS appearing to power off.
The LAP appears to be off with no LED status light as if it has been powered off, but the power supplies are still connected and the LAPS are often warm to the touch as if drawing power even when they have been "off" for a couple of days.
Unplugging the power supply (at the LAP) and re-applying brings the LAP back on.
The LAPS involved all used the recommended Cisco manufactured power supplies as there was no POE/power injector infrastructure.
The LAPS vanish from the WLC as if disconnected, without any apparent errors in the WLC logs.
There are no crash logs for the LAPS which have powered off.
Console output from a LAP which has powered off on startup just shows the AP coming back from a "cold start".
LAPS operate normally after restart, but after avariable period, typically 2-7 days will power off again.
This is happening across multiple sites, to LAPS connected to different WLCs.
Has anyone seen this issue before?

The LAP appears to be off with no LED status light as if it has been powered off, but the power supplies are still connected and the LAPS are often warm to the touch as if drawing power even when they have been "off" for a couple of days.
Gareth,
Just want to make sure you are using a power brick/power injector. Can you please confirm?
Had issues with 7.4 when I noticed that some of my APs, running in PoE, would suddenly get "lost". They would suddenly reboot and they wouldn't negotiate PoE properly. I had to manually shut down the ports for at least 5 seconds. If I don't leave it off for that long the APs simply won't boot up.
Ever since I've moved to 7.5, I haven't seen this happen.
There is a well-known bug, can't seem to find it, about 1140 and WLC firmware 7.4. If I remembered correctly, the bug describes what you are seeing.
You may want investigate in using 7.5.

2112 wlc + lap 1262 problem

Hello
After connecting an AIR-LAP 1262 N to a WLC 2112 (shipped this week) i get a periodic disconnect from AP, heres the log output (debug)
Nov 20 13:35:08 192.168.0.32 Cisco_62:bf:00: *Nov 19 13:25:14.126: %DTLS-5-ESTABLISHED_TO_PEER: openssl_dtls.c:559 DTLS connection established to 192.168.0.149
Nov 20 13:35:08 192.168.0.32 Cisco_62:bf:00: *Nov 19 13:25:14.129: %CAPWAP-3-DUP_AP_NAME: capwap_ac_decode.c:1077 AP with same name AP588d.0937.c0f9 exist. Using default name AP588d.0937.c0f9 for this AP.
Nov 20 13:35:09 192.168.0.32 Cisco_62:bf:00: *Nov 19 13:25:14.224: %DTLS-5-PEER_DISCONNECT: openssl_dtls.c:659 DTLS peer 192.168.0.149 has closed connection.
WLC:
Controller Summary
Management IP Address
192.168.0.32
Software Version
6.0.199.4
Emergency Image Version
System Name
Cisco_62:bf:00
Can someone give us any clue ?
TIA
Gianluca

Hello,
First of all Thanks a lot. In fact i suspected that a version 7 shipped with 1262 AP was not matching the 6.0.199.... and so on. I already tried before posting here to download that version.
BUT
(we are new to Cisco procedures) it seems that to download that fw version we MUST be entitled to some Tech Support Agreement (= PAY ?)
Is that true ? (Isnt kind of strange that 2 very expensive / born to work togheter pieces like that does not work out of the box and we cant even get a fw upgrade ?)
Maybe i am missing something ?
Thanks again
Gianluca

Cisco AIR 1142N wireless speed.

Hello all.
Just got Cisco AIR 1142N, configured it with two ssids on 2.4 Mhz interface. 5.0 is shutdown. As I know (probably I am wrong) wireless speed with "n" mode devices must be at least 150 Mbps, but I get only half of that- 72 Mbps. Where could be a problem?
Tested it with notebooks with Broadcom 4313 adapter.
I have read some people face problem with 54 Mbps speed, but they just have wrong authentication.
Be glad for any advice!
and here is a bit of my conf.

Yeah..I think this is the problem.
My wi-fi adapter in notebooks is Broadcom 4313b/g/n and this is what I find about it..
Broadcom 4313GN 802.11b/g/n
WiFi Adapter
Integrated support for 802.11 b, g, and n
1 transmit, 1 receive antenna
Up to 72 mbps data rate
Very sad.
Thanks everyone for the help and detailed responses:)

Is Cisco air-ap1230a a lightweight access point?

Is Cisco air-ap1230a a lightweight access point? Can it be use for the new CCNP training?
Thanks

Hi Bao,
The 1230 is not a Lightweight AP, but can be upgraded to LWAPP with the A Radio model listed below (Note that this model is EOS/EOL) this is probably not the best choice for your studies;
Solution Requirements
Migration from autonomous access point mode to lightweight mode is possible on these Cisco Aironet access point platforms:
All 1130AG access points
All 1240 AG access points
For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and **1230 AP**) platforms, it depends on the radio:
if 802.11G, MP21G and MP31G are supported
if 802.11A, RM21A and RM22A are supported
The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
All 1310 AG access points
From this good doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html
Cisco Aironet 1200 Series Access Point Ordering Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00800c9435.html
EOS & EOL for the Cisco Aironet 1200 Series 802.11a Access Points
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_eol_notice0900aecd801e5303.html
Understanding the Lightweight Access Point Protocol (LWAPP)
http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd802c18ee.shtml
Lightweight Access Point FAQ
http://www.cisco.com/en/US/products/ps6306/products_qanda_item09186a00806a4da3.shtml
Lightweight AP (LAP) Registration to a Wireless LAN Controller (WLC)
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
**You are probably better off with something like the LAP 1131. Have a look here;
http://www.cisco.com/en/US/products/hw/wireless/products_category_buyers_guide.html#access_points
Hope this helps! I noticed your other post regarding the WLC suggestions and have responded there as well :)
Rob

AIR-LAP 1231G-A-K9

I have a couple of questions: I have a 161 AP,s most of which are AIR-LAP 1231G-A-K9 two 4400 WLC.
Some of these APs are using AIR-ANT 1728 (2.4 GHz omidirectional 5.2 dBi) and Mobile Mark OD9-240 (2-GHz omnidirectional 9 dBi) on the same access points. Some of my AP are PoE and some are using a power supply (at the AP) some are using both. Power level is set at 2 a radios are not enabled just the bg radios. I'm having issues: I need to tweak the APs (Power settings & Channel settings) so my clients (LXE VX6) can refresh faster.
Any suggestions?
PS I did'nt set this up. It was handed to me.

All of the enabled APs have thier A radios disabled.
1231 don't have 802.11a radios. You are using two type of antennaes (5 dBi and 9 dBi) in the SAME UNIT.
The only way to determine if you have proper signal is to walk around with a laptop and sniff out the signal. If you have signal strength of about 65 to 75 dBi then this is good. If your signal being received by the laptop is higher than 80 dBi then this is one of your problems.
Please check if all the data rates for 802.11b and 802.11g are enabled.
You may want to propose to management to upgrade your WAPs as they are old. If they want something cheap (supports only 802.11 a/b/g) and with external antennas then 1240 is your option. If you want internal antenna 1130 is still in the market.
If management want internal antenna and support 802.11 a/b/g/n then the cheapest model is the 1040. The 1260 will support 802.11 a/b/g/n and requires antennas.

Cisco AIR-LAP 1522 PROBLEM

Similar Messages

Maybe you are looking for