CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red, what is this? it isn't in the manual

CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??

No cisco web is working perfectly.
do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
Autonomous AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
LAP AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
Regards

Similar Messages

  • Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

    hi,
    I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives  Ethernet LED = Off; Radio LED = RED ; Status LED = RED  and only next listing in the screen:
    Xmodem file system is available.
    Flashfs[0]: unable to allocate available block.
    The system has been interrupted, or encountered an error during initializion of the flash filesystem.
    The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
    flash_init
    ether_init
    tftp_init
    boot
    When I type this commands, it doesn't help at all. The output will be following:
    ap: flash_init
    Initializing Flash...
    flashfs[0]: out of memory
    ...done Initializing Flash.
    ap: ether_init
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ap: tftp_init
    Unable to get our ip address: no "IP_ADDR" variable set
    ap: boot
    Loading ""...; permission denied
    Error loading ""
    Interrupt within 5 seconds to abort boot process.
    Boot process failed...
    ap:
    what i do ?  please help , thanks

    Duplicate posts.  
    Go here:  http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

  • Problem reseting Cisco AIR- LAP1131AG

    Dear Expert,
    we have customer which used Cisco Air-LAP1131AG and Wireless Lan Controller. The Controller went back to Cisco as Traid in, but we got some AP for our lab.
    Problem is, that when you connect via Console cable it brings you into normal mode >, but when going into enable mode it asks for Password. Problem is, that customer changed password and don´t know anymore.
    Is it possible to reset the password and configure the AP fresh from beginning?
    Thanks
    Klaus

    and another one with 21 seconds
    Press RETURN to get started!
    *Mar  1 00:00:06.295: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
    *Mar  1 00:00:06.302: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:38 by alnguyen
    *Mar  1 00:00:07.236: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:08.236: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:20.136: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0 (not full duplex), with ROUTER_VOICE_LAB FastEthernet0/0 (full duplex).
    *Mar  1 00:00:25.331: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar  1 00:00:34.342: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 192.168.200.183, mask 255.255.255.0, hostname 24
    24>
    24>
    24>ðXmodem file system is available.
    flashfs[0]: 26 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 7131136
    flashfs[0]: Bytes available: 8867840
    flashfs[0]: flashfs fsck took 32 seconds.
    Base ethernet MAC Address: 00:1d:a1:ee:97:b4
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 10 mbps, half-duplex
    Ethernet port 0 initialized: link is up
    button pressed for 21 seconds
    process_config_recovery: set IP address and config to default 10.0.0.1
    process_config_recovery: image recovery
    image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
    examining image...
    %Error opening  (connection timed out)Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################
    File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:38 by alnguyen
    Image text-base: 0x00003000, data-base: 0x0035E440
    Initializing flashfs...
    flashfs[1]: 26 files, 9 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 7131136
    flashfs[1]: Bytes available: 8867840
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
    Processor board ID FCZ1147Q1KT
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 3.0.51.0
    1 FastEthernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:1D:A1:EE:97:B4
    Part Number                          : 73-8962-12
    PCA Assembly Number                  : 800-24818-11
    PCA Revision Number                  : B0
    PCB Serial Number                    : FOC11443WRR
    Top Assembly Part Number             : 800-29144-02
    Top Assembly Serial Number           : FCZ1147Q1KT
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1131AG-E-K9
    % Hostname contains one or more illegal characters.
    Press RETURN to get started!
    *Mar  1 00:00:06.294: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
    *Mar  1 00:00:06.302: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:38 by alnguyen
    *Mar  1 00:00:07.236: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:08.236: %LINEPROTO-5-UP
    24>
    24>DOWN: Line protocol on Interface FastEthernet0, changed state to down
    *Mar  1 00:00:09.820: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    24>
    24>en
    Password:

  • Cisco AIR-CAP26021-A-K9 || Error opening tftp:// ... /ap3g2-k9w7-tar.default

    Hi everyone:
    I have a problem with two Cisco AIR AP's ... I have configured already eight of them (in lightweight mode), but those two send me the next error, right now.
    ap: %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)
    And when I boot to the AP, it says:
    %Error opening flash
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Numonyx Mirrorbit (0089)
    Xmodem file system is available.
    flashfs[0]: 11 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 15 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Ethernet speed is 100 Mb - FULL Duplex
    button is pressed, wait for button to be released...
    button pressed for 21 seconds
    process_config_recovery: set IP address and config to default 10.0.0.1
    process_config_recovery: image recovery
    image_recovery: Download default IOS tar image tftp://255.255.255.255/ap3g2-k9w7-tar.default
    examining image...
    DPAA Set for Independent Mode
    DPAA_INIT = 0x0
    %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)ap:
    ap:
    ap:
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Numonyx Mirrorbit (0089)
    Xmodem file system is available.
    flashfs[0]: 10 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 14 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Ethernet speed is 100 Mb - FULL Duplex
    Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...###########################
    File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 10 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 7 seconds.
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Boot CMD: 'boot  flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
    Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
    File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x2003000
    executing...
    Initializing flashfs...
    flashfs[2]: 10 files, 2 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 31739904
    flashfs[2]: Bytes used: 7245824
    flashfs[2]: Bytes available: 24494080
    flashfs[2]: flashfs fsck took 8 seconds.
    flashfs[2]: Initialization complete.
    flashfs[3]: 0 files, 1 directories
    flashfs[3]: 0 orphaned files, 0 orphaned directories
    flashfs[3]: Total bytes: 11999232
    flashfs[3]: Bytes used: 1024
    flashfs[3]: Bytes available: 11998208
    flashfs[3]: flashfs fsck took 0 seconds.
    flashfs[3]: Initialization complete.
    Copying radio files from flash: to ram:
    %Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
    Uncompressing radio files...
    File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
    File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
    ...done Initializing flashfs.
    Press RETURN to get started!
    *Mar  1 00:00:11.335: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:13.071: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:13.663: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 23:08 by prod_rel_team
    *Mar  1 00:00:13.795: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:13.795: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
    *Mar  1 00:00:13.799: %PARSER-4-BADCFG: Unexpected end of configuration file.
    lwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:14.751: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:16.467: DPAA Initialization Complete
    *Mar  1 00:00:16.467: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:16.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    no bridge-group 1 source-learning
                       ^
    % Invalid input detected at '^' marker.
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:00:47.151: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inline power source
    *Mar  1 00:00:49.515: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.44.221, mask 255.255.255.0, hostname APc067.af6f.3125
    Translating "CISCO-CAPWAP-CONTROLLER.asf.gob.mx"...domain server (10.1.1.2)
    *Mar  1 00:01:00.403: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:01:00.451: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.asf.gob.mx
    The thing is, I've been applying the instruction:
    capwap ap controller ip address 10.4.13.2
    'cause I want them to communicate with a remote controller, and the past eight did it fine, but this two didn't.
    As for the things I've already tried, I have reset it's parameters to it's initial settings, I've tried to load a new IOS image, I've cleared the flash memory, but nothing works, it keeps communicating with the old controller.
    How can I fix this? (I mean, changing or adapting the AP to a lightweight AP)
    Thanks in advance

    Its fine to try to apply it from the console...but if you really want to clear the AP, you need to clear the nvram.  so if changing the primary from the GUI that the AP has joined didn't work, then try this:
    debug capwap console cli
    erase /all nvram
    Example:
    Entered the username and password
    debug capwap console cli
    erase /all nvram:
    [confirm]
    undebug all
    reload
    [confirm]
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Does WiSM 6.0.196.0 suport AIR-LAP1131AG-N-K9 in H-REAP mode

    Hello,
    I have WiSMs running code version 6.0.196.0. I have to deploy AIR-LAP1131AG-N-K9 in H-REAP mode.
    Q1. Does AIR-LAP1131AG-N-K9 require CAPWAP or can run off of LWAPP?
    Q2. Does anyone know how to find out if a WLC is running LWAPP or CAPWAP?
    Q3. If one has to convert LWAPP to CAPWAP, how is it done?
    Thanks
    Bo

    Hi,
    Q1. Does AIR-LAP1131AG-N-K9 require CAPWAP or can run off of LWAPP?
    A1. The AP will run CAPWAP as soon the WLC is running a CAPWAP image. There is nothing special to do on the AP, once it joins the WLC, the WLC will check the image on the AP and if using a diferent one, the WLC will push the correct image to the AP that matchs the WLC version.
    Q2. Does anyone know how to find out if a WLC is running LWAPP or CAPWAP?
    A2. CAPWAP was introuduced in WLC version 5.2 and all versions above are running CAPWAP software.
    •If  your firewall is currently configured to allow traffic only from access  points using LWAPP, you must change the rules of the firewall to allow  traffic from access points using CAPWAP.
    •Make  sure that the CAPWAP UDP ports 5246 and 5247 (similar to the LWAPP UDP  ports 12222 and 12223) are enabled and are not blocked by an  intermediate device that could prevent an access point from joining the  controller.
    •If  access control lists (ACLs) are in the control path between the  controller and its access points, you need to open new protocol ports to  prevent access points from being stranded.
    Q3. If one has to convert LWAPP to CAPWAP, how is it done?
    A1. On the APs nothing has to be done. Once the WLC is running CAPWAP software, it will automatically push the corresponding AP software to the AP.
    WLC runs CAPWAP if the software version is earlier then 5.2. WLC version 5.2 and all versions above are running CAPWAP software.
    HTH,
    Tiago
    If  this helps you and/or answers your question please mark the question as  "answered" and/or rate it, so other users can easily find it.

  • 1252 status blinks red,green,blue

    Hi,
    I'we connected a Cisco 1252 accesspoint to a 802.3af switch, 15.4w.
    And it blinks red, green, blue on the status.
    The accesspoint is autonomous using latest c1250-k9w7-tar.124-21a.JA1. 5Ghz radio is off/disabled.
    but im still getting this in the logs
    "Limited(1x3 MIMO) radio functionality due to insufficient inline power. To get full functionality use enhanced PoE switches, power injectors or power supply."
    If i physically remove the 5Ghz radio the alarms go away and also the error message about mimo 1x3.
    Is there a way to disable the 5ghz radio completeley through software?

    Hi,
    The 5Ghz rasio is already shutdown.
    Any other idéas?
    Current configuration : 1657 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname ap
    enable secret 5 $1$XIx.$a9uUCWpvrJHHW60CT/VgE/
    no aaa new-model
    dot11 syslog
    dot11 ssid TESTWLAN
    authentication open
    guest-mode
    power inline negotiation prestandard source
    username Cisco password 7 072C285F4D06
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    ssid TESTWLAN
    antenna gain 0
    beamform ofdm
    speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio1
    no ip address
    no ip route-cache
    shutdown
    ssid TESTWLAN
    antenna gain 0
    no dfs band block
    channel dfs
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.1.1 255.255.255.0
    no ip route-cache
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    bridge 1 route ip
    line con 0
    line vty 0 4
    login local
    end

  • I received this error message when trying to use my time capsule.  MacBook Air.sparsebundle is already in use.  What does this mean?

    I received this error message when trying to use my time capsule.  Macbook Air.sparsebundle already is use.  What does this mean?

    First, restart the MacBook Air and the Time Capsule. In most of the cases, this solves the problem.
    If not, see > http://pondini.org/TM/C12.html

  • Export iPhoto slideshow to a DVD, but get message "OS Status Error -9459".  What does this mean?

    I have created a slideshow (with music) in iPhoto, and each time that I try to export the slideshow, iPhoto stops the process and gives me the error message "OS Status Error -9459".  What does this mean?

    Go into the System/Energy Saver preference pane and turn OFF all options.  Also turn off the screensaver. Then try again.
    OT

  • Cisco 1131AG LWAP status led yellow and other leds blinking green

    I have a problem with three AIR-LAP1131AG-E-K9  that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
    The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
    The SSID broadcast is enabled.
    On the switch the interface is up and there is traffic going in and out of the LAP.
    I tired power reset and factory reset for the APs but the problem remains the same.
    Any ideas for what might be the problem ?!!
    Regards

    Yes the clients are not able to see the SSID broadcasted by the AP.
    But these APs were functioning normally before without any changes to the WLC config.
    I had the same problem with other APs but they went back to normal state after a hardware reset to the APs.

  • Cisco AIR-AP1242AG-A-K9 Vs AIR-LAP1131AG-N-K9 Which AP is best

    Dear All,
    I am confused between AIR-AP1242AG-A-K9 and AIR-LAP1131AG-N-K9, we have WLC 4400 which supports both, which one will be the best.
    and what are the adv. adn disadv. of both.
    Thanks,
    Almas...

    Almas,
         Depends on what you are looking to do.  Both are good for any standard deployment, i.e. office space, hallways.
    The 1242 is a bit more flexible as it has external antenna that can be articulated.  So you can mount it on a wall, or on the ceiling.  The down side, is they will be visible.
    The 1131 has built-in antenna, and is designed to be mounted horizontally, on a ceiling for example.
    So depending on where you can mount, that will determine the type of AP you need to use

  • AIR-LAP1131AG issue

    I've connected an AIR-LAP1131AG to a 3560G and can see the port being granted power in the logs but nothing else - nothing in CDP, port is showing as down/down.  The Status LED on the top of the AP is showing as blue/green, which according to the docs means it's initializing the Flash filesystem, but it just sits there.  I've installed 12 APs and two of them have this issue.  I know they all worked a few weeks back because i upgraded the software on them to 7.0.98.0 before shipping them to site.
    Any ideas as to what could be the cause?  Could it be a cabling issue?  These two APs are on the same floor of a building and i'm wondering if the cabling has been botched.  I can't imagine both of them developing a hardware fault, but the status LED may suggest otherwise.  Any thoughts appreciated.
    Thanks in advance,
    Jason

    That did the trick!  See below - good port on both switches followed by the APs on g0/48...  Thanks for your help!
    SW13#show cable-diagnostics tdr int g0/1
    TDR test last run on: April 03 14:23:31
    Interface Speed Local pair Pair length        Remote pair Pair status
    Gi0/1     1000M Pair A     21   +/- 4  meters Pair A      Normal
                    Pair B     21   +/- 4  meters Pair B      Normal
                    Pair C     21   +/- 4  meters Pair C      Normal
                    Pair D     19   +/- 4  meters Pair D      Normal
    SW13#show cable-diagnostics tdr int g0/48
    TDR test last run on: April 03 14:23:35
    Interface Speed Local pair Pair length        Remote pair Pair status
    Gi0/48    auto  Pair A     46   +/- 4  meters N/A         Open
                    Pair B     68   +/- 4  meters N/A         Normal
                    Pair C     102  +/- 4  meters N/A         Fail
                    Pair D     110  +/- 4  meters N/A         Fail
    SW14#show cable tdr int g0/1
    TDR test last run on: April 03 14:24:56
    Interface Speed Local pair Pair length        Remote pair Pair status
    Gi0/1     1000M Pair A     22   +/- 4  meters Pair A      Normal
                    Pair B     21   +/- 4  meters Pair B      Normal
                    Pair C     21   +/- 4  meters Pair C      Normal
                    Pair D     22   +/- 4  meters Pair D      Normal
    SW14#show cable tdr int g0/48
    TDR test last run on: April 03 14:24:59
    Interface Speed Local pair Pair length        Remote pair Pair status
    Gi0/48    auto  Pair A     46   +/- 4  meters N/A         Open
                    Pair B     68   +/- 4  meters N/A         Normal
                    Pair C     98   +/- 4  meters N/A         Fail
                    Pair D     102  +/- 4  meters N/A         Fail

  • Cisco AIR-LAP1041N-E-K9 not working with WLC 4402 version 7.0.116.0

    Hi All,
    appreciate your support for a problem i started facing today. i have a Cisco WLC 4402 running version 7.0.116.0 and it is working great with 25 Cisco 1252 APs. we have recieved a new 20 Cisco 1041N APs today and i installed one in our site but it doesn't work. it worked fine and loaded the image from flash and got the WLC ip address through DHCP option and started showing the below error:
    *Mar  1 00:00:10.021: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:10.033: *** CRASH_LOG = YES
    *Mar  1 00:00:10.333: Port 1 is not presentSecurity Core found.
    Base Ethernet MAC address: C8:9C:1D:53:57:5E
    *Mar  1 00:00:11.373: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:11.465: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1088 messages)
    *Mar  1 00:00:11.494:  status of voice_diag_test from WLC is false
    *Mar  1 00:00:12.526: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:13.594: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:13.647: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Wed 13-Apr-11 12:50 by prod_rel_team
    *Mar  1 00:00:13.647: %SNMP-5-COLDSTART: SNMP agent on host APc89c.1d53.575e is undergoing a cold start
    *Mar  1 00:08:59.062: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:08:59.062: bsnInitRcbSlot: slot 1 has NO radio
    *Mar  1 00:08:59.138: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:08:59.837: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:09:00.145: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:09:09.136: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.26.81, mask 255.255.255.0, hostname APc89c.1d53.575e
    *Mar  1 00:09:17.912: %PARSER-4-BADCFG: Unexpected end of configuration file.
    *Mar  1 00:09:17.912:  status of voice_diag_test from WLC is false
    *Mar  1 00:09:17.984: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:09:19.865: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:09:19.886: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:09:20.873: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:09:20.874: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
    Translating "CISCO-CAPWAP-CONTROLLER.atheertele.com"...domain server (172.16.40.240)
    *Mar  1 00:09:29.029: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.16.100.102 obtained through DHCP
    *May 25 08:27:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:02.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *May 25 08:27:03.175: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:03.177: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
    *May 25 08:27:03.177: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *May 25 08:27:03.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *May 25 08:27:03.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
    *May 25 08:27:03.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
    *May 25 08:27:03.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
    *May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:03.378: bsnInitRcbSlot: slot 1 has NO radio
    *May 25 08:27:03.448:  status of voice_diag_test from WLC is false
    *May 25 08:27:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:14.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *May 25 08:27:15.185: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:15.186: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
    *May 25 08:27:15.186: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *May 25 08:27:15.330: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *May 25 08:27:15.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
    *May 25 08:27:15.334: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
    *May 25 08:27:15.334: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
    *May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:15.379: bsnInitRcbSlot: slot 1 has NO radio
    *May 25 08:27:15.450:  status of voice_diag_test from WLC is false
    *May 25 08:27:26.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:26.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *May 25 08:27:27.182: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:27.183: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
    *May 25 08:27:27.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *May 25 08:27:27.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *May 25 08:27:27.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
    *May 25 08:27:27.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
    *May 25 08:27:27.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
    *May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:27.377: bsnInitRcbSlot: slot 1 has NO radio
    *May 25 08:27:27.433: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *May 25 08:27:27.446: %PARSER-4-BADCFG: Unexpected end of configuration file.
    *May 25 08:27:27.447:  status of voice_diag_test from WLC is false
    *May 25 08:27:27.448: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *May 25 08:27:27.456: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *May 25 08:27:38.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:38.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *May 25 08:27:39.183: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:39.184: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
    *May 25 08:27:39.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *May 25 08:27:39.326: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *May 25 08:27:39.329: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
    *May 25 08:27:39.329: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
    *May 25 08:27:39.330: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
    *May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:39.375: bsnInitRcbSlot: slot 1 has NO radio
    *May 25 08:27:39.446:  status of voice_diag_test from WLC is false
    *May 25 08:27:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:49.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *May 25 08:27:50.179: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
    *May 25 08:27:50.180: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
    *May 25 08:27:50.180: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *May 25 08:27:50.323: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *May 25 08:27:50.326: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
    *May 25 08:27:50.326: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
    *May 25 08:27:50.326: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
    *May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *May 25 08:27:50.370: bsnInitRcbSlot: slot 1 has NO radio
    *May 25 08:27:50.425: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *May 25 08:27:50.438: %PARSER-4-BADCFG: Unexpected end of configuration file.
    i searched for the regulatory domains difference between  AIR-LAP1041N-E-K9 and  AIR-LAP1041N-A-K9 and didn't find any difference that may affect the operation of this AP.
    just to mention that our configuration in WLC for regulatory domains is:
    Configured Country Code(s) AR 
    Regulatory Domain  802.11a:  -A
                                 802.11bg: -A
    My question is, should i only include my country in the WLC (IQ) to add the requlatry domain (-E) to solve this problem? or changing the country will affect the operation of all working APs??
    Appreciate your kind support,
    Wisam Q.

    Hi Ramon,
    thank you for the reply but as shown in the below link:
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7.0.html#wp233793
    the WLC in version 7.0.116.0 supports Cisco 1040 seiries APs.
    Thanks,
    Wisam Q.

  • Cisco AIR-LAP 1522 PROBLEM

    Hello to everyone. They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
    IOS Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 18 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 15537664
    flashfs[0]: Bytes available: 16331264
    flashfs[0]: flashfs fsck took 23 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: 00:27:0c:27:3f:00
    Low Power PoE - enabling LAN Ethernet port only
    Loading "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB"...###################################################################################################################################################################################################
    File "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 06-Jul-10 14:49 by prod_rel_team
    Proceeding with system init
    Proceeding to unmask interrupts
    Initializing flashfs...
    flashfs[1]: 18 files, 2 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 31352832
    flashfs[1]: Bytes used: 15537664
    flashfs[1]: Bytes available: 15815168
    flashfs[1]: flashfs fsck took 5 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    Warning:  the compile-time code checksum does not appear to be present.
    Radio0  present A600 8000 A8020000 0 A8030000 30
    Radio1  present A600 8000 B8020000 0 B8030000 13
    Radio2 not present 0 0 0 0 0 11
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    %Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-LAP1522AG-E-K9   (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
    Processor board ID FCW1346W00Q
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from power loss
    LWAPP image version 6.0.199.0
    4 Gigabit Ethernet interfaces
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:27:0C:27:3F:00
    Part Number                          : 73-10918-04
    PCA Assembly Number                  : 800-28909-04
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC13430YBS
    Top Assembly Part Number             : 800-29338-04
    Top Assembly Serial Number           : FCW1346W00Q
    Top Revision Number                  : F0
    Product/Model Number                 : AIR-LAP1522AG-E-K9
    % Please define a domain-name first.
    flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
    Press RETURN to get started!
    Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:00:07.231: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.575: m8349_ether_enable: MACCFG1 sync timeout
    *Mar  1 00:00:08.079: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:08.579: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:08.655: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1297 messages)
    *Mar  1 00:00:08.683: AP identified to be in Huck Jr/1240/1130 configuration
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
    *Mar  1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
    *Mar  1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
    *Mar  1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
    *Mar  1 00:00:10.695: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 06-Jul-10 14:49 by prod_rel_team
    *Mar  1 00:00:10.695: %SNMP-5-COLDSTART: SNMP agent on host wifikal.Laiki-agora is undergoing a cold start
    *Mar  1 00:00:10.759: Warning: Failed to run startup script
    *Mar  1 00:00:10.771: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
    *Mar  1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:12.771: %LINK-3-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:18.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
    *Mar  1 00:00:20.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:00:22.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
    flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
    *Mar  1 00:00:25.771: No Mesh startup file found
    *Mar  1 00:00:29.763: Logging LWAPP message to 0.0.0.0.
    *Mar  1 00:00:31.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:00:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:31.987: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:45.355: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED WS-C2960-8TC-L (0025.b413.b802)
    *Mar  1 00:00:45.355:  -Verify the required power-injector is installed on this port: WS-C2960-8TC-L(Fas 0/2).
    *Mar  1 00:00:45.355:  -If a power-injector is installed, issue the command:"power inline negotiation injector installed"
    *Mar  1 00:01:26.015: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    *Mar  1 00:01:34.515: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:01:36.515: %LINK-3-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:01:37.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:01:39.563: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:03:05.575: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallback to DHCP.
    *Mar  1 00:03:15.583: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:03:15.703: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 20.20.20.37, mask 255.255.255.0, hostname wifikal.Laiki-agora
    *Mar  1 00:03:15.703: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to process timer message.
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
    Translating "CISCO-CAPWAP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
    *Mar  1 00:03:20.751: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    Translating "CISCO-LWAPP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
    *Mar  1 00:03:21.759: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:03:21.815: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.TelestoHQ
    *Mar  1 00:03:21.871: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.TelestoHQ
    *Mar  1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
    *Mar  1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
    *Mar  1 00:04:37.583: %MESH-6-LINK_UPDOWN: Mesh station 0027.0c27.3ffc link Down

    Search this doc for "reset"
    http://www.cisco.com/en/US/docs/wireless/technology/mesh/design/guide/MeshAP_52.html
    Reset Button
    The access point has a reset button located on the bottom of the unit (see Figure 3). The reset button is recessed in a small hole that is sealed with a screw and a rubber gasket. The reset button is used to perform these functions:
    •Reset the access point—press the reset button for less than 10 seconds. LEDs turn off during the reset and then reactivate when the reset is complete.
    •Disable battery backup power—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
    –You can also disable the battery remotely by entering this command:
    config mesh battery-state disable AP_name
    •Switch off LEDS—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
    Figure 3 Reset Button Location
    1
    Reset button location
    Sent from Cisco Technical Support iPhone App

  • AIR-LAP1131AG-N-K9 getting failed repeatedly

    Hi Experts,
    we are having more than 250 - AIR-LAP1131AG-N-K9 access point installed,
    We are facing issue in access point which SN is starting from FTX1216, its getting failed and not starting by PoE or power adaptor (dead)
    i analyzed all these failed access points and found that a copper metal foil which covered on some part on PCB of Access point is half removed. and all this access points are 3 to 4 Years older. is there any way to stop such failures.
    find attachted snap shot.

    Using a TFTP Server to Return to a Previous Release
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    Please don't forget to rate our useful posts.  Thanks.

  • Cisco Air-SAP-1602I-A-K9

    I just bought a Cisco Air-SAP 1602I-A-K9 and am trying to use the GUI to set it up.  I can't even get to the GUI.  I connected the RJ45 cable to the console on the Cisco side and the other side to the ethernet side of my computer and used the browser to go to 192.168.1.1 and nothing.

    RJ45 cable to the console on the Cisco side
      You should connect RJ45 cable onto Ethernet (not to the console) port of the AP & other end to PoE switch to power the AP (or to a PC if ap powered by an injector).
    Easiest thing would be connect a console calbe to the console port & access the CLI of the AP (username/password should be cisco/Cisco & enable password Cisco). Then verify what is the IP configured on BVI1 interface using "show ip interface brief" command as shown below.
    ap#sh ip int brief
    Interface                  IP-Address      OK? Method Status                Protocol
    BVI1                       192.168.31.55   YES other  up                    up     
    Dot11Radio0                unassigned      YES unset  administratively down down   
    Dot11Radio1                unassigned      YES unset  administratively down down   
    FastEthernet0              unassigned      YES other  up                    up   
    If you do not see an IP on your BVI1 interface then you need to configure it manually (unless you connect it to DHCP configured switchport)
    ap(config)#int bvi1
    ap(config-if)#ip address 192.168.1.1 255.255.255.0
    ap(config)#ip default-gateway 192.168.1.x
    You can use as Laptop IP as gateway if you just need to do the initial configs.
    HTH
    Rasika
    **** Pls rate all useful responses *****

Maybe you are looking for

  • Microphone not found after installing Windows 8.1

    My PC was purchased in Greece 5-6 years ago (I don't remember exactly) Initially, it came with Windows 7 and later on I  upgraded it to Windows 8 with no problems at all. Then, on January 2014  I installed Windows 8.1, and as aresult my microphone is

  • Can you share photos with others through iCloud

    with mobileme going away, is there a way to share iPhoto photos/albums with others through iCloud?

  • How do I get rid of crossdomain which throws me into Explorer?

    Every time I open a new page on Bloomberg, Firefox opens 2 windows in Internet Explorer associated with crossdomain. I need to eliminate this function.

  • Possibility of individual V2 postings for depreciation

    Dear experts, We have implemented parallel accounting using account method for company code 3DEM. Thus, for depreciation area 10 we have configured it to do a V2 update posting. While posting depreciation, the system generates two accounting document

  • Open and modify an existing file in java

    Supposed I have a file called myfile.txt, its content is below: XYZT..... ...keyword: mykeyword ABCD..... I would like to open it, go to the "keyword", modify the string "mykeyword" to "changedkeyword" then save the file. Note that I want to save the