Cisco Air-Lap1242AG
Hi i was trying to create a better stronger wireless network at my house. I picked up a Cisco Air-Lap1242AG on an auction thinking it would give me more range. Now trying to set it up i am trying to figure out if i made a mistake? Can this router be used at home with just a Cable Modem? Or does this need to hook into a Business Network?
Thanks
Eric
A Cisco "Air-LAP" access point is useless standalone by itself. It must participate on a network with a Cisco
Wireless Lan Controller appliance to configure and manage it.
And it's just an access point, not a router too, like a typical home unit is. Looks like you bought the wrong tool for the job.
In my opinion, the best performing consumer-grade wireless routers (for max range, and typical Internet surfing 802.11g speeds) I've ever encountered, for home use have been the old Buffalo Wireless-G High Power units, which I think you can still buy online these days.
Similar Messages
-
WLC 5508 and Cisco Aironet 1242 LWAPP AIR-LAP1242AG-A-K9
i have deployed wlc 5508 ( image 7.0.98.0 ) with 1262N AP and all 45 AP's are working fine,
at the same site i had AP1242 which i have converted to LWAPP (8 of them), these accesspoint are registerd perfectly with 5508 but non of the radio's are up. i have selected different countries according to the part numbers but unfortunaly non of the radio's are coming up, pleaes help
SatheesAvailable:370.0(w) Used:32.4(w) Remaining:337.6(w)
Interface Admin Oper Power Device Class
(Watts)
Fa0/1 auto off 0.0 n/a n/a
Fa0/2 auto off 0.0 n/a n/a
Fa0/3 auto off 0.0 n/a n/a
Fa0/4 auto off 0.0 n/a n/a
Fa0/5 auto off 0.0 n/a n/a
Fa0/6 auto off 0.0 n/a n/a
Fa0/7 auto off 0.0 n/a n/a
Fa0/8 auto off 0.0 n/a n/a
Fa0/9 auto off 0.0 n/a n/a
Fa0/10 auto off 0.0 n/a n/a
Fa0/11 auto off 0.0 n/a n/a
Fa0/12 auto off 0.0 n/a n/a
Fa0/13 auto off 0.0 n/a n/a
Fa0/14 auto off 0.0 n/a n/a
Fa0/15 auto off 0.0 n/a n/a
Fa0/16 auto off 0.0 n/a n/a
Fa0/17 auto off 0.0 n/a n/a
Fa0/18 auto off 0.0 n/a n/a
--More--
Interface Admin Oper Power Device Class
(Watts)
Fa0/19 auto off 0.0 n/a n/a
Fa0/20 auto off 0.0 n/a n/a
Fa0/21 auto off 0.0 n/a n/a
Fa0/22 auto off 0.0 n/a n/a
Fa0/23 auto off 0.0 n/a n/a
Fa0/24 auto off 0.0 n/a n/a
Fa0/25 auto off 0.0 n/a n/a
Fa0/26 auto off 0.0 n/a n/a
Fa0/27 auto off 0.0 n/a n/a
Fa0/28 auto off 0.0 n/a n/a
Fa0/29 auto off 0.0 n/a n/a
Fa0/30 auto off 0.0 n/a n/a
Fa0/31 auto off 0.0 n/a n/a
Fa0/32 auto off 0.0 n/a n/a
Fa0/33 auto off 0.0 n/a n/a
Fa0/34 auto off 0.0 n/a n/a
Fa0/35 auto off 0.0 n/a n/a
Fa0/36 auto off 0.0 n/a n/a
Fa0/37 auto off 0.0 n/a n/a
Fa0/38 auto off 0.0 n/a n/a
Fa0/39 auto off 0.0 n/a n/a
Fa0/40 auto off 0.0 n/a n/a
Fa0/41 auto on 15.0 cisco AIR-LAP1242AG Class 3
--More--
Interface Admin Oper Power Device Class
(Watts)
Fa0/42 auto off 0.0 n/a n/a
Fa0/43 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/44 auto off 0.0 n/a n/a
Fa0/45 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/46 auto off 0.0 n/a n/a
Fa0/47 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/48 auto off 0.0 n/a n/a -
Hi,
I setup a mini wireless LAN network lab with a not for resale 2106 wireless lan controller and a sales air-lap1242ag access point. I do not have a DHCP and DNS in my lab environment. I have configured the WLC with the basic configuration using the CLI wizard, i also configured the WLC as a DHCP server for clients that will be connecting to the APs associated to the controller.
I powered up the AP and connect the ethernet port directly to the controller, the controller issued an IP address to the AP, the AP downloaded a new operating system from the controller but failed to join the controller.
I check both debug message on the controller console and the trap messages on the controller's GUI and it say the AP could not download a configuration from the controller and it is beacuse of invalid license. Below is the trap message:
Configuration Phase Statistics
Requests Received
Responses Sent
Unsuccessful Request Processed
Reason For Last Unsuccessful Attempt
Last Successful Attempt Time
Last Unsuccessful Attempt Time
Last Error Summary
Last AP Message Decryption Failure
Last AP Connection Failure
Last Error Occurred
Last Error Occurred Reason
Last Join Error Timestamp
Also, I tried to log into the GUI of the AP using the both the username and password ''Cisco'' but I cannot get into the device. I can only get in through the CLI. In the CLI, almost all the commands I enter gives an error the it is disabled. I don't know what to do any more, I want to know if the access point is faulty or i am not doing the right thing.
PLEASE HELP!!!!!!!!!!!!!!!!!!!Thank you for the quick response.
The controller is running firmware version:
Software Version 6.0.199.4
Emergency Image Version 6.0.199.4
The AP can ping the Management IP address of the controller successfully via console. I have also entered in the AP the WLC's Management IP address information and it is still the same. Below is the message I'm getting on the console of the AP it self:
*Jul 9 13:06:09.803: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jul 9 13:06:10.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip:
192.168.50.246 peer_port: 5246
*Jul 9 13:06:10.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Jul 9 13:06:11.636: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.50.246 peer_port: 5246
*Jul 9 13:06:11.638: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.50.246
*Jul 9 13:06:11.638: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Jul 9 13:06:11.724: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Jul 9 13:06:11.726: %DTLS-5-ALERT: Received WARNING : Close notify alert from
192.168.50.246
*Jul 9 13:06:11.727: %DTLS-5-PEER_DISCONNECT: Peer 192.168.50.246 has closed conne
ction.
*Jul 9 13:06:11.727: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 1
92.168.50.246:5246
*Jul 9 13:06:11.772: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jul 9 13:06:11.772: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
I will also like to know if AIR-LAP1242AG is compatible with WLC 2106 controller.
Any help will be greatly appreciated, i really need to resolve this issue in my LAB now so that I don't go to my customer site to fumble.
thanks in advance. -
Low power warning for AIR-LAP1242AG-C-K9
Hi Buddie,
We purchased some AIR-LAP1242AG-C-K9 , but not perchasing any wireless controller. When I connect the LAP to Cat2950 or Cat2960 PPoE port, all the LAP can not boot normally. It indicates low power, please refer the two pictures attached. But if I use external power cable, the LAP can work well. So, I would like to know two things.
1. Can I use LAP standalone without using controller ?
2. If the above is Yes, how should I configure the PPoE on cat2950 to Support LAP correctly?
Thank you very much.Hi Jian,
Q. Can an LAP operate independent of a wireless LAN controller (WLC)?
A. No, LAPs cannot function independent of WLCs. LAPs function in conjunction with a WLC only. The reason is that the WLC provides all the configuration parameters and firmware that the LAP needs in the registration process.
So you will need to either send the AP's back and get the IOS version, purchase a WLC or convert the LAP to IOS :(
Q. How do I distinguish between a regular (autonomous) AP and an LAP?
A. The easiest way to distinguish between a regular AP and a LAP is to look at the part number of the AP.
LAP (Lightweight AP Protocol [LWAPP])?Part numbers always begin with AIR-LAPXXXX.
Autonomous AP (Cisco IOS? Software)?Part numbers always begin with AIR-APXXXX.
From this good Q&A doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a00806a4da3.shtml
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob -
AIR-LAP1242AG-A-K9 configure command does not seem to exist
I have an AIR-LAP1242AG-A-K9. Straight out of the box I thought it would have the GUI functional but this is not the case. I am brand new to Cisco products so it is taking me a while to get use to them and to TelNet but from what I have read in about 6 different manuals none have explained how I can access the configure terminal command when It doesn't show up. I am in privileged mode with access of:
AP001c.588e.a266#show privilege
Current privilege level is 15
Version is 12.3(7)JA1, RELEASE SOFTWARE (fc1). I haven't changed any settings except the ip settings and time and date.
AP001c.588e.a266# ? gives me
cd Change current directory
clear Reset functions
clock Manage the system clock
crypto Encryption related commands.
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
enable Turn on privileged commands
exit Exit from the EXEC
fsck Fsck a filesystem
help Description of the interactive help system
led LED functions
lock Lock the terminal
login Log in as a particular user
logout Exit from the EXEC
lwapp lwapp exec commands
mkdir Create new directory
more Display the contents of a file
name-connection Name an existing network connection
no Disable debugging functions
ping Send echo messages
but no configure command
If I try to use the configure command I get
AP001c.588e.a266#configure terminal
^
% Invalid input detected at '^' marker
If it helps any if I use show configuration command:
startup-config is not present
If I can't get into global configuration mode I cant enable the GUI, turn on the wireless, or do much of anything else so I need some help.
Any would be appreciated,
Matt BrownHi Matt,
The problem here is that the AP you received is a Lightweight AP which is meant to be used with Wireless Lan Controllers and WCS. The "LAP" portion of the part number shows this Lightweight designation. This can be converted to an Autonomous/stand-alone AP that you desire;
Here is a conversion method;
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob -
WLC 5508 with version 7.0.98.0 and AIR-LAP1242ag
hi, recently i have deployed wlc 5508 with ap 1262. initially i had trouble with the existing version on the wlc (6..0.199.0) which AIR-LAP1262N-E-K9 was not registering with wlc. i have upgraded the wlc to 6.0.199.4 ver still it was not registering. finally i have upgraded to 7.0.98.0 and all the 40 AP's ( AIR-LAP1262N-E-K9 ) are addedd and its working fine.
Now my issue is, at the same site i have 12 nos of AIR-LAP1242ag autnomous AP's which i need to convert to lightweight ap and register with wlc. where i am stuck currently. after loading the recovery image (c1240-rcvk9w8-tar.123-7.JX9.tar) the ap reboots and can see it register with wlc within seconds contollers pushed the new image and once the ap reboots, never register again.
does anyone has any idea?After adding the country codes GB and RU.. in my test setup 1242 is registered...i will have it run for couple hours and see the result
ref: below
(Cisco Controller) >show ap uptime
Number of APs.................................... 2
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Ethernet MAC AP Up Time Association Up Time
AP1cdf.0f66.79ca 1c:df:0f:66:79:ca 0 days, 00 h 43 m 35 s 0 days, 00 h 42 m 36 s
AP001e.be27.a7e6 00:1e:be:27:a7:e6 0 days, 00 h 16 m 56 s 0 days, 00 h 07 m 15
This issue sorted...thanks -
Good afternoon,
My name is Dave and my company has assigned me to fix an issue with the signal from a WLAN 5508 Controller to several ( maybe 12) AIR-LAP1242AG's in a warehouse location.
We are currently using a single 5 GHz anntenna but are looking into other options.
The issue we are having is the signal strength. We are using Windows CE scan guns and the wireless is weak at best (even if you stand directly under the AP.
Since I am brand new to the job, I am unfamiliar with our topology but will do what I can to resolve this issue. Could the issue be a combination of power, antenna strength and something in the controller perventing the signal from passing?
The ceilings in the warehouse rafters are between 25-30ft. I will be happy to assist anyone that might be able to point us in the right direction.
I have yet to look into the AP's console but I wanted to get possibly a few ideas.
Thank you so much for your time and consideration in solving our issue.
Sincerely,
Dave P./* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thank you so much for your response. Here are the answers to your questions.
1. Are the APs installed suspended from the ceiling and the "Cisco" logo pointing to the floor? Yes
2. Are the 5Ghz antennae being used? Yes How many per unit? 1 – 2
Are they connected to the correct radio? Yes What type of antennaes? AIR-ANT5135D-R
3. What are the walls of the warehouses made out of? Concrete
4. Are there any electric motors? Just forklifts
5. Are the APs above or below the level of the shelves? Above
6. Was a Wireless Site Survey conducted before and after the APs were installed? No
7. Is the WLC's Radio Resources Meter set to it's default level? ???? We are not sure of this one yet.
I hope this helps.
Thank you so much!
-Dave -
Cisco AIR-CAP1602I-E-K9 Telnet issue
Hi Team, I have installed new cisco AIR-CAP1602I-E-K9 in the remote site LAN however the access point received the ip address through central DHCP helper address. I am able to ping the access point through LAN but I am unable to telenet the device to configure.
Also when Field enginner visited on site to connect physical he connected through console but we were not able get into configure mode though we had full privilege access.
Please advice.
AP0006.f618.26f5#sh version
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP0006.f618.26f5 uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FGL1703ZA3E
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:06:F6:18:26:F5
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC164971SY
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1703ZA3E
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xFThanks,
1. Does it mean I should not be able to telnet also into the AP though I can ping from Router LAN ( AP is connected directly to router ethernet interface).
2. I am also not able to discover controller when running in controller-based IOS. getting below errors.
Thanks to advice on above points.
Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:04.042: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
AP0006.f618.26f5#
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.1
AP0006.f618.26f5#1.13
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:14.042: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:24.029: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
Not in Bound state.
*Mar 1 00:03:49.505: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:53.393: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:03:53.477: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.93.22, mask 255.255.255.128, hostname AP0006.f618.26f5
en
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.50.1.235) (10.50.1.236)
*Mar 1 00:04:00.505: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:04:00.565: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:10.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:20.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:04:30.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
Not in Bound state.
*Mar 1 00:04:46.069: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:04:49.161: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:04:49.273: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.115.20, mask 255.255.255.128, hostname AP0006.f618.26f5
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.50.1.235)
*Mar 1 00:04:57.069: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP. (10.50.1.236)
*Mar 1 00:05:15.068: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
Not in Bound state.
*Mar 1 00:06:00.568: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:06:04.396: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:06:04.412: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.93.22, mask 255.255.255.128, hostname AP0006.f618.26f5
en
AP0006.f618.26f5#
AP0006.f618.26f5#sh
Writing out the event log to flash:/event.log ...
ip int
*Mar 1 00:06:11.668: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Could not discover WLC using DHCP IP address, Reload to use static IP. -
Cisco AIR-LAP 1131 reboot in loop
Hi Everyone
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00CD9790 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000C3
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00CDB580 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x0184C8AA R17 = 0x0184C71B R18 = 0x00CDB760 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00CD9790
Frame 00: SP = 0x00CD97D0 PC = 0x0048A6A8
Frame 01: SP = 0x00CDB728 PC = 0x004361FC
Frame 02: SP = 0x00CDB740 PC = 0x0042E078
Frame 03: SP = 0x00CDB758 PC = 0x0044880C
Frame 04: SP = 0x00CDB798 PC = 0x0042A280
Frame 05: SP = 0x00CDB7C0 PC = 0x0042AA68
Frame 06: SP = 0x00000000 PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute,
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
And this is all it does, and keep loading the image. I already know the recovery procedure to reset it, but i wanted to know how i can put these AP in HREAP without having these issues. In the setup we need, we cannot have those AP be in local mode.
Thanks for any help and consideration .
RegardsHi Scott
Thanks for replying
here is the full output between loops :
Press RETURN to get started!
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
Translating "CISCO-LWAPP-CONTROLLER.aimfire.net"...domain server (10.1.10.100) [OK]
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed sta
15:52:12 UTC Fri Mar 1 2013: Unexpected exception to CPUvector 1100, PC = 0x5A9048 , LR = 0x48A8A0
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
CPU Register Context:
MSR = 0x00029230 CR = 0x53000035 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Writing crashinfo to flash:/crashinfo_20130301-155213
=== Flushing messages (15:52:20 UTC Fri Mar 1 2013) ===
Buffered messages:
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed state to UP
*Mar 1 15:52:11.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Queued messages:
*Mar 1 15:52:23.534: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Mar 1 15:52:11.414: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Nested exception_rom_monitor call (2 times)
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00D1EC18
Frame 00: SP = 0x00D1EC58 PC = 0x0048A6A8
Frame 01: SP = 0x00D20BB0 PC = 0x004361FC
Frame 02: SP = 0x00D20BC8 PC = 0x0042E078
Frame 03: SP = 0x00D20BE0 PC = 0x0044880C
Frame 04: SP = 0x00D20C20 PC = 0x0042A280
Frame 05: SP = 0x00D20C48 PC = 0x0042AA68
Frame 06: SP = 0x00000000 PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute, 7 seconds
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
flashfs[0]: 40 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 15129600
flashfs[0]: Bytes available: 869376
flashfs[0]: flashfs fsck took 41 seconds.
Base ethernet MAC Address: d8:67:d9:ba:9f:2e
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2"...###############################################
File "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
Image text-base: 0x00003000, data-base: 0x005AEE20
Initializing flashfs...
flashfs[1]: 40 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 15129600
flashfs[1]: Bytes available: 869376
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio 1 A506 7100 E8000000 A0000000 80000000 3
Radio 0 0 0 0 0 0 2
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from unknown reload cause - reason ptr 0xF, PC 0x5A9048, address 0x0
LWAPP image version 4.1.192.35
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: D8:67:D9:BA:9F:2E
Part Number : 73-13304-02
PCA Assembly Number : 800-36409-01
PCA Revision Number : B0
PCB Serial Number : FOC16304BZJ
Top Assembly Part Number : 800-29582-03
Top Assembly Serial Number : FTX1632N00D
Top Revision Number : A0
Product/Model Number : AIR-LAP1131G-A-K9
Press RETURN to get started!
Also , the switchport is a trunk port, i can definitely try it an access port . -
Cisco AIR-CAP26021-A-K9 || Error opening tftp:// ... /ap3g2-k9w7-tar.default
Hi everyone:
I have a problem with two Cisco AIR AP's ... I have configured already eight of them (in lightweight mode), but those two send me the next error, right now.
ap: %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)
And when I boot to the AP, it says:
%Error opening flash
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 11 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 15 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: c0:67:af:6f:31:25
Ethernet speed is 100 Mb - FULL Duplex
button is pressed, wait for button to be released...
button pressed for 21 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/ap3g2-k9w7-tar.default
examining image...
DPAA Set for Independent Mode
DPAA_INIT = 0x0
%Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)ap:
ap:
ap:
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 10 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 14 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: c0:67:af:6f:31:25
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...###########################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 10 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7245824
flashfs[0]: Bytes available: 24752128
flashfs[0]: flashfs fsck took 7 seconds.
Base Ethernet MAC address: c0:67:af:6f:31:25
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x2003000
executing...
Initializing flashfs...
flashfs[2]: 10 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31739904
flashfs[2]: Bytes used: 7245824
flashfs[2]: Bytes available: 24494080
flashfs[2]: flashfs fsck took 8 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete.
Copying radio files from flash: to ram:
%Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
Uncompressing radio files...
File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
...done Initializing flashfs.
Press RETURN to get started!
*Mar 1 00:00:11.335: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:13.071: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.663: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:08 by prod_rel_team
*Mar 1 00:00:13.795: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:13.795: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
*Mar 1 00:00:13.799: %PARSER-4-BADCFG: Unexpected end of configuration file.
lwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:14.751: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:16.467: DPAA Initialization Complete
*Mar 1 00:00:16.467: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:16.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:47.151: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inline power source
*Mar 1 00:00:49.515: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.44.221, mask 255.255.255.0, hostname APc067.af6f.3125
Translating "CISCO-CAPWAP-CONTROLLER.asf.gob.mx"...domain server (10.1.1.2)
*Mar 1 00:01:00.403: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:00.451: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.asf.gob.mx
The thing is, I've been applying the instruction:
capwap ap controller ip address 10.4.13.2
'cause I want them to communicate with a remote controller, and the past eight did it fine, but this two didn't.
As for the things I've already tried, I have reset it's parameters to it's initial settings, I've tried to load a new IOS image, I've cleared the flash memory, but nothing works, it keeps communicating with the old controller.
How can I fix this? (I mean, changing or adapting the AP to a lightweight AP)
Thanks in advanceIts fine to try to apply it from the console...but if you really want to clear the AP, you need to clear the nvram. so if changing the primary from the GUI that the AP has joined didn't work, then try this:
debug capwap console cli
erase /all nvram
Example:
Entered the username and password
debug capwap console cli
erase /all nvram:
[confirm]
undebug all
reload
[confirm]
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Error logs on AIR-LAP1242AG-A-K9
Hi gents,
From "show log" I got the following error logs, please help to understand what does it complain about ? this AIR-LAP1242AG-A-K9 , version "c1240-k9w8-mx.124-25e.JAM2". The address of 172.16.6.21 is our WLC.
Thanks for all help.Hi,
Step1
a. Choose Wireless> 802.11a/n > Network.
b. Unselect the 802.11a Network Status check box.
c. Click Apply to commit your changes.
d. Choose Wireless > 802.11b/g/n > Network.
e. Unselect the 802.11b/g Network Status check box.
f. Click Apply to commit your changes.
Step 2 Choose Wireless > Country and uncheck the box for the country which you dnt want to put your WLC in.
after changing the country code, dont forget to enable both networks(802.11a and 802.11b/g)
Reagrds
Dont forget to rate helpful posts -
CISCO AIR-AP1252AG-E-K9 is keep rebooting with no reason
Hello
I have an cisco AIR-AP1252AG-E-K9 and it reeboots randomly with no aparent reason
this is the configuration
aaa group server radius rad_eap
server 10.10.1.2 auth-port 1645 acct-port 1646
aaa group server radius rad_mac
aaa group server radius rad_acct
server 10.10.1.2 auth-port 1645 acct-port 1646
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
clock timezone +0200 2
ip domain name diamant.local
dot11 activity-timeout unknown default 32400
dot11 activity-timeout client default 32400 maximum 32400
dot11 activity-timeout repeater default 32400 maximum 32400
dot11 activity-timeout workgroup-bridge default 32400 maximum 32400
dot11 activity-timeout bridge default 32400 maximum 32400
dot11 ssid cisco
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa
guest-mode
dot11 ssid diamant4
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa
guest-mode
dot11 arp-cache
power inline negotiation prestandard source
username root privilege 15 password 7 060506324F41
username Cisco privilege 15 password 7 1047051613121F120D0A2D2E2862626C7A46
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid diamant4
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel width 40-above
channel 2412
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid cisco
dfs band 1 3 block
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel width 40-above
channel dfs
station-role root
payload-encapsulation dot1h
world-mode legacy
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
logging history size 200
no cdp run
radius-server attribute 32 include-in-access-req format %h
radius-server host 10.10.1.2 auth-port 1645 acct-port 1646 key 7 13011E13060D0A3E
radius-server vsa send accounting
bridge 1 route ip
and the logs
*Mar 1 00:00:06.207: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.035: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.543: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 02:00:09.599 +0200: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:09 UTC Fri Mar 1 2002 to 02:00:09 +0200 Fri Mar 1 2002, configured from console by console.
*Mar 1 02:00:09.755 +0200: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 02:00:09.763 +0200: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 02:00:09.767 +0200: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
*Mar 1 02:00:09.767 +0200: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 20:39:11.027 +0200: %SSH-5-ENABLED: SSH 1.99 has been enabled
*Mar 1 20:39:11.027 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 20:39:11.027 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 20:39:11.531 +0200: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 20:39:11.531 +0200: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 20:39:13.055 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 20:39:13.055 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 20:39:14.311 +0200: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 20:39:17.919 +0200: %DOT11-6-DFS_SCAN_START: DFS: Scanning frequency 5280 MHz for 60 seconds.
*Mar 1 20:39:17.919 +0200: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5280 selected
*Mar 1 20:39:17.919 +0200: %DOT11-4-FREQ_CHANGED: Interface Dot11Radio1, channel or channel width changed: 40Mhz above not allowed on channel
*Mar 1 20:39:17.923 +0200: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 20:39:17.931 +0200: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Apr 6 12:05:00.537 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Apr 6 12:05:00.537 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Apr 6 12:05:00.709 +0200: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.10.1.243, mask 255.255.255.0, hostname ap
Apr 6 12:05:32.729 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station PC186 5894.6b5d.6c00 Associated KEY_MGMT[WPAv2]
Apr 6 12:05:34.325 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
Apr 6 12:05:34.481 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.305d Associated KEY_MGMT[WPAv2]
Apr 6 12:05:35.117 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 0025.9cde.155a Associated KEY_MGMT[WPAv2]
Apr 6 12:05:45.493 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.2fe0 Associated KEY_MGMT[WPAv2]
Apr 6 12:05:59.545 +0200: %DOT11-6-DFS_SCAN_COMPLETE: DFS scan complete on frequency 5280 MHz
Apr 6 12:06:06.561 +0200: %DOT11-6-ASSOC: Interface Dot11Radio1, Station 0025.9cf8.9149 Associated KEY_MGMT[WPAv2]
Apr 6 12:06:56.471 +0200: %DOT11-6-ASSOC: Interface Dot11Radio1, Station 0025.9cde.0fc5 Associated KEY_MGMT[WPAv2]
Apr 6 12:08:11.008 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0025.9cde.155a Reason: Previous authentication no longer valid
Apr 6 12:08:11.016 +0200: %DOT11-4-MAXRETRIES: Packet to client 0025.9cde.155a reached max retries, removing the client
Apr 6 12:08:14.124 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 0025.9cde.155a Associated KEY_MGMT[WPAv2]
Apr 6 12:08:17.608 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0025.9cde.155a Reason: Previous authentication no longer valid
Apr 6 12:08:48.950 +0200: %DOT11-7-AUTH_FAILED: Station 0025.9cde.155a Authentication failed
Apr 6 12:08:48.950 +0200: %DOT11-4-MAXRETRIES: Packet to client 0025.9cde.155a reached max retries, removing the client
Apr 6 12:09:12.978 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 0025.9cde.155a Associated KEY_MGMT[WPAv2]
Apr 6 12:25:35.510 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.305d Reason: Sending station has left the BSS
Apr 6 12:25:35.530 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.305d Associated KEY_MGMT[WPAv2-CP]
Apr 6 12:35:32.229 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
Apr 6 12:35:32.245 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2-CP]
Apr 6 12:37:27.996 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
Apr 6 12:37:28.016 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2-CP]
Apr 6 12:54:07.729 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.2fe0 Reason: Previous authentication no longer valid
Apr 6 12:54:09.457 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.2fe0 Associated KEY_MGMT[WPAv2]
Apr 6 12:54:36.236 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.2fe0 Reason: Previous authentication no longer valid
Apr 6 10:54:56.515: Client 687f.74fb.2fe0 failed: reached maximum retries
Apr 6 12:55:37.141 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.2fe0 Associated KEY_MGMT[WPAv2]
Apr 6 13:30:07.002 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 5894.6b5d.6c00 Reason: Sending station has left the BSS
Apr 6 13:30:17.442 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
Apr 6 13:30:17.802 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2-CP]
Apr 6 13:34:59.087 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.3b1f reached max retries, removing the client
Apr 6 13:34:59.087 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Previous authentication no longer valid
Apr 6 13:35:02.743 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
Apr 6 13:35:23.451 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.3b1f reached max retries, removing the client
Apr 6 13:35:23.455 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Previous authentication no longer valid
Apr 6 13:35:26.743 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
Apr 6 13:36:40.768 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
Apr 6 13:38:59.004 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
Apr 6 13:40:56.655 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
Apr 6 13:40:56.703 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2-CP]
Apr 6 13:56:42.322 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0025.9cf8.9149 Reason: Previous authentication no longer valid
Apr 6 13:56:45.490 +0200: %DOT11-6-ASSOC: Interface Dot11Radio1, Station 0025.9cf8.9149 Associated KEY_MGMT[WPAv2]
Apr 6 13:56:49.302 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0025.9cf8.9149 Reason: Previous authentication no longer valid
Apr 6 11:57:11.623: Client 0025.9cf8.9149 failed: reached maximum retries
Apr 6 14:12:43.510 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.305d Reason: Sending station has left the BSS
Apr 6 14:12:43.526 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.305d Associated KEY_MGMT[WPAv2-CP]
Apr 6 14:49:12.472 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.305d Reason: Previous authentication no longer valid
Apr 6 14:49:15.628 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.305d Associated KEY_MGMT[WPAv2]
Apr 6 14:49:21.672 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.305d Reason: Previous authentication no longer valid
Apr 6 14:49:53.282 +0200: %DOT11-7-AUTH_FAILED: Station 687f.74fb.305d Authentication failed
Apr 6 14:49:53.282 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.305d reached max retries, removing the client
Apr 6 14:52:04.097 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station PC186 5894.6b5d.6c00 Associated KEY_MGMT[WPAv2]
Apr 6 15:14:29.682 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0025.9cde.155a Reason: Previous authentication no longer valid
Apr 6 15:15:03.124 +0200: %DOT11-7-AUTH_FAILED: Station 0025.9cde.155a Authentication failed
Apr 6 15:15:03.124 +0200: %DOT11-4-MAXRETRIES: Packet to client 0025.9cde.155a reached max retries, removing the client
Apr 6 15:21:02.660 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Previous authentication no longer valid
Apr 6 15:21:02.664 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.3b1f reached max retries, removing the client
Apr 6 15:21:05.780 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
Apr 6 15:21:09.808 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Previous authentication no longer valid
Apr 6 15:21:41.058 +0200: %DOT11-7-AUTH_FAILED: Station 687f.74fb.3b1f Authentication failed
Apr 6 15:21:41.058 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.3b1f reached max retries, removing the client
Apr 6 15:24:36.911 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0025.9cde.0fc5 Reason: Previous authentication no longer valid
Apr 6 15:24:41.435 +0200: %DOT11-7-AUTH_FAILED: Station 0025.9cde.0fc5 Authentication failed
Apr 6 15:24:45.131 +0200: %DOT11-6-ASSOC: Interface Dot11Radio1, Station 0025.9cde.0fc5 Associated KEY_MGMT[WPAv2]
Apr 6 15:24:54.127 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0025.9cde.0fc5 Reason: Previous authentication no longer valid
Apr 6 15:25:27.623 +0200: %DOT11-7-AUTH_FAILED: Station 0025.9cde.0fc5 Authentication failed
Apr 6 15:25:27.623 +0200: %DOT11-4-MAXRETRIES: Packet to client 0025.9cde.0fc5 reached max retries, removing the clienti found something about how to reach the maximum N speed
Factors that Affect 802.11n Throughput
There are circumstances where 802.11n devices cannot operate at their maximum capable data rates. There are various reasons why this occurs. This is the list of factors that affect 802.11n throughput:
When 802.11n clients operate in a mixed environment with 802.11a or 802.11 b/g clients, 802.11n provides a protection mechanism to interoperate with 802.11a or 802.11 b/g clients. This introduces an overhead and reduces the throughput of 802.11n devices. Maximum throughput is achieved in Greenfield mode where only 802.11n clients exist.
Factors such as Channel width, Guard Interval and Reduced IFS (RIFS) play a major role in the bandwidth. Table 1 and Table 2 show how these factors affect the bandwidth.
Clients ability to send a Block Ack instead of individual frame acknowledgements.
MCS Index configured on the WLC.
Proximity to AP—Clients closer to the AP experience higher data rates. As clients move farther away from the AP, signal strength reduces. As a result, data rate decreases steadily.
RF environment—Amount of noise and interference in the environment. The less the noise and interference, the greater the bandwidth.
Encryption/ Decryption—Encryption in general reduces the throughput due to the overhead involved in the data encryption/decryption process. However, advanced encryption standards, such as AES, can provide better throughput when compared to other encryption standards, such as TKIP and WEP.
Wired Network Infrastructure—Bandwidth of the wired infrastructure determines the speed of the traffic to and from the wired network to the wireless clients.
If using an AP1250, change the AP to H-REAP mode for a 5-10% boost.
If using an AP1140, keep the AP in local mode and enable TCP MSS on the controller. Use the config ap tcp-adjust-mss enable all 1363 command in order to enable it.
Disable RRM scanning to prevent any throughput drops when going off channel. This can yield a 1-3% improvement.
Disable RLDP to ensure the AP does not attempt to connect to rogue devices during testing.
Use a Wireless Controller 5508 as the data plane is superior to the 4404-series.
My questions are:
1. How i can i put the access point to operate only in N mode (because all my clients are N)
2.The guard interval can be modify ?
3. How to put my AP in H-REAP (can i do this without WLC?)
4. How to disable RRM
5.How to disable RLDP.
Thank you. -
Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;
hi,
I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives Ethernet LED = Off; Radio LED = RED ; Status LED = RED and only next listing in the screen:
Xmodem file system is available.
Flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error during initializion of the flash filesystem.
The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
ether_init
tftp_init
boot
When I type this commands, it doesn't help at all. The output will be following:
ap: flash_init
Initializing Flash...
flashfs[0]: out of memory
...done Initializing Flash.
ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ap: tftp_init
Unable to get our ip address: no "IP_ADDR" variable set
ap: boot
Loading ""...; permission denied
Error loading ""
Interrupt within 5 seconds to abort boot process.
Boot process failed...
ap:
what i do ? please help , thanksDuplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red -
CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??
No cisco web is working perfectly.
do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
Autonomous AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
LAP AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
Regards -
Hello to everyone. They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 18 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 15537664
flashfs[0]: Bytes available: 16331264
flashfs[0]: flashfs fsck took 23 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 00:27:0c:27:3f:00
Low Power PoE - enabling LAN Ethernet port only
Loading "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB"...###################################################################################################################################################################################################
File "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 18 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31352832
flashfs[1]: Bytes used: 15537664
flashfs[1]: Bytes available: 15815168
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio0 present A600 8000 A8020000 0 A8030000 30
Radio1 present A600 8000 B8020000 0 B8030000 13
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
%Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-LAP1522AG-E-K9 (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
Processor board ID FCW1346W00Q
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power loss
LWAPP image version 6.0.199.0
4 Gigabit Ethernet interfaces
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:27:0C:27:3F:00
Part Number : 73-10918-04
PCA Assembly Number : 800-28909-04
PCA Revision Number : A0
PCB Serial Number : FOC13430YBS
Top Assembly Part Number : 800-29338-04
Top Assembly Serial Number : FCW1346W00Q
Top Revision Number : F0
Product/Model Number : AIR-LAP1522AG-E-K9
% Please define a domain-name first.
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
Press RETURN to get started!
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:07.231: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.575: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:08.079: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:08.579: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:08.655: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1297 messages)
*Mar 1 00:00:08.683: AP identified to be in Huck Jr/1240/1130 configuration
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
*Mar 1 00:00:10.695: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 06-Jul-10 14:49 by prod_rel_team
*Mar 1 00:00:10.695: %SNMP-5-COLDSTART: SNMP agent on host wifikal.Laiki-agora is undergoing a cold start
*Mar 1 00:00:10.759: Warning: Failed to run startup script
*Mar 1 00:00:10.771: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:12.771: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:18.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:20.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:22.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
*Mar 1 00:00:25.771: No Mesh startup file found
*Mar 1 00:00:29.763: Logging LWAPP message to 0.0.0.0.
*Mar 1 00:00:31.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:31.987: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:45.355: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED WS-C2960-8TC-L (0025.b413.b802)
*Mar 1 00:00:45.355: -Verify the required power-injector is installed on this port: WS-C2960-8TC-L(Fas 0/2).
*Mar 1 00:00:45.355: -If a power-injector is installed, issue the command:"power inline negotiation injector installed"
*Mar 1 00:01:26.015: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:01:34.515: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:01:36.515: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:01:37.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:39.563: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:03:05.575: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallback to DHCP.
*Mar 1 00:03:15.583: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:15.703: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 20.20.20.37, mask 255.255.255.0, hostname wifikal.Laiki-agora
*Mar 1 00:03:15.703: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
Translating "CISCO-CAPWAP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:20.751: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
Translating "CISCO-LWAPP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
*Mar 1 00:03:21.759: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:03:21.815: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.TelestoHQ
*Mar 1 00:03:21.871: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.TelestoHQ
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 1 00:04:37.583: %MESH-6-LINK_UPDOWN: Mesh station 0027.0c27.3ffc link DownSearch this doc for "reset"
http://www.cisco.com/en/US/docs/wireless/technology/mesh/design/guide/MeshAP_52.html
Reset Button
The access point has a reset button located on the bottom of the unit (see Figure 3). The reset button is recessed in a small hole that is sealed with a screw and a rubber gasket. The reset button is used to perform these functions:
•Reset the access point—press the reset button for less than 10 seconds. LEDs turn off during the reset and then reactivate when the reset is complete.
•Disable battery backup power—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
–You can also disable the battery remotely by entering this command:
config mesh battery-state disable AP_name
•Switch off LEDS—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
Figure 3 Reset Button Location
1
Reset button location
Sent from Cisco Technical Support iPhone App
Maybe you are looking for
-
I've got a new ipod and i'm trying to get all my songs on it that I have in i-tunes from my old ipod, and when I look at it through i-tunes it shows that all the songs are on my new ipod but when I disconnect it - the ipod has no songs on it. What am
-
Adobe Design Standard for Student
Hi there, I'd like to purchase Adobe Design Standard. But I have a big problem understanding the system you are working with. I'm a student from Romania in the 1st year of Political Sciency University and I'd like to get and Adobe Design Standard for
-
Elements will not install on windows 8.1 64 bit.
1st I notice 7 zip gives me broken file errors when extracting the zip. Then I get initialization error when trying to install. I've tried it all..cc cleaner, re-downloaded a million times, hours on chat support, desktop sharing. Using the hidden adm
-
Traffic in SXMS_XI_AUDIT_DISPLAY doesn't match traffic in RWB Perf Mon
I have got a traffic log in RWB: Time Interval: last month Agregation Interval: one month Other options initial. So the traffic is Size*Number. But that value doesn't match result of SXMS_XI_AUDIT_DISPLAY report in XI ABAP... What the cause of this
-
Had my Nikon D600 recently in for the updated service call. Camera works fine but Photoshop says it cannot open my RAW (NEF) files now? It worked fine before and I have done all my updates.