Cisco Aironet 1130

I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?

I would like to enable SNMP on the device so that our SolarWinds Orion NPM server can monitor the device
Ok. NOOOOOOOOOOOW I understand you.
You need to enable one of two types of SNMP communities: Read Only or Read-Write.
For example, if your SNMP community is TV for Read-only and RADIO for Read-Write then it's this:
snmp-server community TV ro
snmp-server community RADIO rw

Similar Messages

Dual SSID (with dual VLAN) on Cisco AiroNet 1130

Cisco Community,
I need some major help in figuring out how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
I have no idea how to create a VLAN and implement it but I can generally figure things out with a little help. The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
Hope everyone is enjoying their holidays.
Thanks,
Cody

Cody,
Here is a good doc to follow... it explains multiple ssid's and vlans
https://supportforums.cisco.com/docs/DOC-14496
Sent from Cisco Technical Support iPad App

Cisco aironet 1130 and Intermec CV30

Hi to all,
I've a little problem with three Cisco 1130 AP. Anticipately i tell you that i'm not a guru of cisco wireless, but my implementation is very simple. I need a roaming for the 3 AP. I only have Ap, so i configure one as Master Ap and the others like repeater with cisco aironet extension configured. All 3 on the same channel and only the Master one broadcast SSID. Wep security implemented. My Cv30 terminals randomly loose the signal also if they're near an AP. They use windows mobile but i think is only a wrong config problem. I need help. Thank you very much.
Alex

The device is using the LWAPP image.. please upgade the same to autonomous image and convert the same..
Please use the below doc that i hv written and this will helpu!!
https://supportforums.cisco.com/docs/DOC-14960
Please dont forget to rate the usefull posts!!
Regards
Surendra

Cisco Aironet 1200 LAP Issues - LAP to Autonomous Mode

Greetings! After purchasing 4 of the Cisco Aironet 1200 G Series WAPs, I'm now running into a slight issue with them.
I received these last week with the understanding that if I didn't have the Cisco controller device, I could convert them from being the Lightweight Access Point, back to Autonomous mode with an IOS.
With this, I checked the documentation that came with the device and found the "Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode" or http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&needs_authentication=yes&CommCmd=MB%3Fcmd%3Dadd_discussion%26mode%3Dshow%26needs_authentication%3Dyes%26location%3D.ee7c7c3.
From there, I followed the instructions listed under Converting a Lightweight Access Point Back to Autonomous Mode. Before the rename of the file, I checked the device and found AIR-LAP1242G-A-K9 for the Model No.
One of the Cisco Certified admins here was able to obtain the latest build for the IOS for the device or c1240-k9w7-tar.123-8.JEB1.tar. Per the instructions, I renamed the file to coincide with the model of the device.
I followed the instructions from there, and it looked as if everything was going well. However, after the upgrade, I'm running into an issue with the following:
File "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1" uncompressed and installed, entry point: 0x3000
executing...
At this point, the device just locks up. All lights are lit green on the device. According do the documentation, it should reboot and from there, I should be able to access the web interface by IP.
I've tried to perform the upgrade again using the same IOS build, but the same thing happens with the lock up.
At this point, I'm assuming the issue is with the build of the IOS that I have and I may have to look at getting an older build. However, before doing so, I thought I would post something here to see if anyone had an idea.
I may have needed to refine my searching of the forums, but wasn't able to find anything in relation to my issue. If there is something out there, I do apologize for the post and will happily refer to any current information.
If you need any further information in relation to this, please let me know. Any assistance is greatly appreciated. Thank you!

Hi Jeffrey,
Reverting the Access Point Back to Autonomous Mode
Have a look at Step 3
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

How to change default admin password on Cisco Aironet 1040

How do I change the default username and password on the Cisco Aironet 1040. There is a default set and I want to change that to secure the device. I've checked the manual and can't seem to find the directions. Any ideas?

Hi Brian,
If this AP is already registered with a WLC then you can change it via WLC.
In WLC GUI, go to Wireless -> Select the AP -> Credential -> Override Global Credential-> Update username/pw/enable pw
In WLC CLI, you can configure it like this. If it is for all APs, then select all, otherwise AP name.
(WLC3) >config ap mgmtuser add username admin password Cisco123 secret Cisco123 ?
all Applies the configuration to every AP that does not have a specific user name.
Enter the name of the Cisco AP.
(WLC3) >config ap mgmtuser add username password secret
(WLC3) >save config
Are you sure you want to save? (y/n) y
If it is Autonomous AP you can configure using the "username xxxx password xxx" IOS command
HTH
Rasika
*** Pls rate all useful responses ****

How many users are supported on a Cisco Aironet 1141N? 30?

I have a client that wants to upgrade his Aironet 1131 APs with 1141N. How many users are supported on a Cisco Aironet 1141N?

Yes, you could have 30 clients on the AP.
Client density all depends on what the client is doing, really.
So if you have clients that are just web surfing and pulling email 30+ isn't a problem. If they are all streaming video, then you want to plan for less clients per AP, and more APs.
Steve

How to load a boot image to cisco aironet 1140 series after missing boot image

Hi all,
I need a solution for this. When i switch my cisco aironet 1140 , it s blinking with red light .and gives a message "no boot image to load".
When i tried next time, by pressing escape it shows this message that i have mentioned below.
ap:
ap:
using eeprom values
WRDTR,CLKTR: 0x83000800 0x40000000
RQDC ,RFDC : 0x80000035 0x00000208
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0x40000000
RQDC, RFDC : 0x80000035, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialized
PCIEx: initialization done
flashfs[0]: 1 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 1536
flashfs[0]: Bytes available: 32383488
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 28:94:0f:d6:c8:62
Ethernet speed is 100 Mb - FULL duplex
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Tue 18-Oct-11 14:51 by prod_rel_team
ap:
So , now my question is how to load the boot image ? From where will we get this ? OR
I m also having another Cisco aironet 1140 , Can i get bootimage from that . Kindly let me know the solution from genius ?

Take a look at this link as it should have the info you need
https://supportforums.cisco.com/docs/DOC-14636
Sent from Cisco Technical Support iPhone App

Cisco Aironet 1300 QoS

Hello, I have 2 Cisco Aironet 1300 Bridges which provide data and voice communication between 2 buildings. Up until recently QoS has not been needed, but lately there appears to be congestion due to reports of poor voice quality. Building A houses a V3000 NBX Telephone system, Building B houses approximately 30 remote IP phones. Building A and Building B are approximately 100 yards apart. No VLAN's. Due to myself being an extreme noob to Cisco bridges, I was hoping some of you may have had experience in setting this up and hopefully provide some tips. I need to prioritize traffic on UDP ports 2093-2096 and TCP port 1040. Thank you in advance for any suggestions. My current running config is below:
Using 1283 out of 32768 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LHS-WeightRoom-WCV
ip subnet-zero
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 ssid wcv
authentication open
guest-mode
dot11 ssid wcvcisco
authentication open
infrastructure-ssid optional
username root privilege 15 password 7 0247335A05320A2244
username Cisco privilege 15 password 7 074E164D403D1C061F
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid wcv
ssid wcvcisco
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
54.0
station-role root bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 10.141.8.6 255.255.254.0
no ip route-cache
ip default-gateway 10.141.8.5
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end

Here is the URL for the configuration of Cisco Aironet 1300 QoS. Follow the guide it may help you
http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html

Hello,good day problem with Cisco aironet 1040 series acces point

Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
mel

helo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040 sir?
waiting for a step by step instruction,
thank you in advance
mel

Aironet 1130 Configuration

We have a Cisco Aironet 1130AG Access Point in our Community Centre.
It was originally installed by the County Council, with no security password set.
We were unable to access the AP as the technician who installed it had changed the password from the default, but hadn't recorded it (and has now left).
We therefore did a Factory Reset, which has enabled us to configure the AP. However, there are a few problems:
1) If the AP is re-booted, it loses all the settings;
2) We can't save the Current Startup Configuration;
3) We don't seem to be able to change the default password.
Regards
Adrian Cobley

The fact that you can't save the configuration or that it gets deleted after a reboot, points to an issue with the nvram, it might be a hardware failure.
However as George said, paste the configuration to take a look, also issue a show ver and let us know which version are you using.

Configuring CISCO AIRONET AP

Hello;
how to configure the IP Adress of CISCO AIRONET 1600i AP to access It through the Web browser and configure It?
we tried to assign a static IP using CLI so we downloaded Tera Term and tried to connect It using the DB Cable. The following message shows up:
*Mar 1 01:41:43.674: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
we tried to execute 'Enable' command and It works then we tried to execute 'config t' command but failed (the other commands do not work too):
APf07f.06f0.93b5#config t
^ % Invalid input detected at '^' marker.
I connected the Aironet AP to a Router which has 192.168.1.1 as a default IP Adress and thats what shows up on the terminal:
Translating "CISCO-CAPWAP-CONTROLLER.Home"...domain server (192.168.1.1)
*Mar 1 00:34:05.251: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:34:05.255: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.Home
Not in Bound state.
*Mar 1 00:34:50.754: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:34:53.766: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:34:53.830: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.5, mask 255.255.255.0, hostname APf07f.06f0.93b5

Hi
By default these AP comes with lightweight image & require a WLC to manage it.(unless you specifically order this AP with autonomous image)
If you want to convert it autonomous (to use without a WLC) then you have to load an autonomous image to it. You should have an image like this (ap1g2-k9w7-tar.153-3.JAB.tar) to begin with (you may require a valid maintenance contract to download this from cisco web site)
Then you can follow one of the methods to convert it to a autonomous AP
1. http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
2. http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/
HTH
Rasika

Cisco Aironet 1300 series

Hello,
i have 2 cisco aironet 1300 series configured as root bridge and non root bridge, i managed to configure them and they are associating only when they adjacent , when i separate them them communication fail , could you please help me to solve this . thx

Those are very old bridges. So if they are still functioning okay, do they require external antennas or not and do you have external antennas if they do?
Antenna Interface
• AIR-BR1310G-x-K9 or AIR-LAP1310G-x-K9: Air interface (integrated directional antenna)
• AIR-BR1310G-x-K9-R or AIR-LAP1310G-x-K9R: Two RP-TNC type connectors for external antennas
-Scott

Cisco Aironet 1300 - Coverage area

Hi,
could you please tell me what is the max coverage area that supports on Cisco Aironet 1300 with integrated antenna (13 dbi).

Check out the following URLs
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
and
http://www.cisco.com/en/US/products/ps5861/prod_brochure09186a0080230777.html

Cisco Aironet

I got a Cisco Aironet card to replace the Broadcom that uses ndiswrapper. Here is what happens
modprobe airo
modprobe airo_ca
then run iwconfig
eth1 (which is my wireless card) no wireless extensions
A few places suggested that it is the driver. Anyone have any other suggestions? Does anyone use a Cisco Aironet card? How did you get it installed?

i have aironet 350
modprobe
yenta_socket , pcmcia_core , airo , & airo_cs
in rc.conf
lo="lo 127.0.0.1"
#eth0="dhcp"
eth1="dhcp"
INTERFACES=(lo !eth0 eth1)
DAEMONS=(syslog-ng !hotplug pcmcia network netfs crond )
but since the upgrades that came out the other day
it doesnt work at boot up i have to unplug then plugin card
run as root
ifconfig -a
dhcpcd eth1 or i could use
dhcpcd wifi0
from what ive read so far its a udev prob havent been able to figure it out yet
so im plugging away at that

Cisco Aironet 1510

On the Cisco Aironet 1500 Series Lightweight Outdoor Mesh Access Point spec sheet from the Cisco.com website, it states that the input power for the DC inline POE is 28.5 W at 48 VDC, nominal. What is the maximum power at 48 VDC? On AC, the nominal power is 57.8W at 120 VAC. What is the maximum power at 120 VAC?
Also, I see that the Cisco 1510 only uses AC as a source. Does Cisco have a device for the Cisco Aironet 1510 that uses DC as a source? For example, instead of using the POE Injector that Cisco has, which uses an input of 120VAC (1.5A) and outputs 48VDC (1.2A), does Cisco have a POE Injector that uses an input of 12VDC and outputs 48VDC (1.2A).

I think the maximum draw (with both radios and heater on) is 57.8 Watts, but with the heater not active it's much lower around 36.84 Watts.

Cisco Aironet 1130

Similar Messages

Maybe you are looking for