Cisco aironet 1130g
hi
i tried to assign ip address to my access point in Lightweight mode using command
AP(config)# interface bvi 1
but it doent continue give error "invalid input detected at "' marker
please help..thank you
Then you cannot use lightweight access points :-)
I would suggest reconfiguring them as autonomous IOS access points.
Download the IOS software for that AP model and install it on the AP, then it will be configurable like a normal IOS device.
The command is "archive download-sw /f /o tftp:///"
If it doesn't allow you to type that command try typing "debug lwapp console cli" or "debug capwap console cli" first but you need to be connected via console (no telnet).
Hope this helps !!!
Nicolas
===
Don't forget to rate answers that you find useful
Similar Messages
-
Cisco aironet 1130g and windows 2003 with cisco ACS
hi
i have configured windows 2003 server with DNS ,Active directory users and dhcp server. and configured my cisco 1130g AP .
i have installed cisco access control server 4.0 because i use LEAP authentication protocol and for the ACS for network configuration i give aaa client ip addresss as AP interface ip and same shared secret for the AP and ACS,.
so when i log to wifi it ask username and password
problem is lap top cannot have a ip address my dhcp server not issue any ip address .
my hiper terminal massage is like this when i connect to wifi
help ...thank you...As I mentioned now several times already, it is the client and ACS which do the PEAP. The Access point doesn't have to be configured for an eap type. What you did on the AP was setting the AP as a radius server which is duplicate work with what you did on ACS.
So you need on your client to configure either PEAP or LEAP.
Nicolas -
How to change default admin password on Cisco Aironet 1040
How do I change the default username and password on the Cisco Aironet 1040. There is a default set and I want to change that to secure the device. I've checked the manual and can't seem to find the directions. Any ideas?
Hi Brian,
If this AP is already registered with a WLC then you can change it via WLC.
In WLC GUI, go to Wireless -> Select the AP -> Credential -> Override Global Credential-> Update username/pw/enable pw
In WLC CLI, you can configure it like this. If it is for all APs, then select all, otherwise AP name.
(WLC3) >config ap mgmtuser add username admin password Cisco123 secret Cisco123 ?
all Applies the configuration to every AP that does not have a specific user name.
Enter the name of the Cisco AP.
(WLC3) >config ap mgmtuser add username password secret
(WLC3) >save config
Are you sure you want to save? (y/n) y
If it is Autonomous AP you can configure using the "username xxxx password xxx" IOS command
HTH
Rasika
*** Pls rate all useful responses **** -
How many users are supported on a Cisco Aironet 1141N? 30?
I have a client that wants to upgrade his Aironet 1131 APs with 1141N. How many users are supported on a Cisco Aironet 1141N?
Yes, you could have 30 clients on the AP.
Client density all depends on what the client is doing, really.
So if you have clients that are just web surfing and pulling email 30+ isn't a problem. If they are all streaming video, then you want to plan for less clients per AP, and more APs.
Steve -
How to load a boot image to cisco aironet 1140 series after missing boot image
Hi all,
I need a solution for this. When i switch my cisco aironet 1140 , it s blinking with red light .and gives a message "no boot image to load".
When i tried next time, by pressing escape it shows this message that i have mentioned below.
ap:
ap:
using eeprom values
WRDTR,CLKTR: 0x83000800 0x40000000
RQDC ,RFDC : 0x80000035 0x00000208
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0x40000000
RQDC, RFDC : 0x80000035, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialized
PCIEx: initialization done
flashfs[0]: 1 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 1536
flashfs[0]: Bytes available: 32383488
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 28:94:0f:d6:c8:62
Ethernet speed is 100 Mb - FULL duplex
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Tue 18-Oct-11 14:51 by prod_rel_team
ap:
So , now my question is how to load the boot image ? From where will we get this ? OR
I m also having another Cisco aironet 1140 , Can i get bootimage from that . Kindly let me know the solution from genius ?Take a look at this link as it should have the info you need
https://supportforums.cisco.com/docs/DOC-14636
Sent from Cisco Technical Support iPhone App -
Hello, I have 2 Cisco Aironet 1300 Bridges which provide data and voice communication between 2 buildings. Up until recently QoS has not been needed, but lately there appears to be congestion due to reports of poor voice quality. Building A houses a V3000 NBX Telephone system, Building B houses approximately 30 remote IP phones. Building A and Building B are approximately 100 yards apart. No VLAN's. Due to myself being an extreme noob to Cisco bridges, I was hoping some of you may have had experience in setting this up and hopefully provide some tips. I need to prioritize traffic on UDP ports 2093-2096 and TCP port 1040. Thank you in advance for any suggestions. My current running config is below:
Using 1283 out of 32768 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LHS-WeightRoom-WCV
ip subnet-zero
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 ssid wcv
authentication open
guest-mode
dot11 ssid wcvcisco
authentication open
infrastructure-ssid optional
username root privilege 15 password 7 0247335A05320A2244
username Cisco privilege 15 password 7 074E164D403D1C061F
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid wcv
ssid wcvcisco
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
54.0
station-role root bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 10.141.8.6 255.255.254.0
no ip route-cache
ip default-gateway 10.141.8.5
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
endHere is the URL for the configuration of Cisco Aironet 1300 QoS. Follow the guide it may help you
http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html -
Hello,good day problem with Cisco aironet 1040 series acces point
Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
melhelo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040 sir?
waiting for a step by step instruction,
thank you in advance
mel -
Hello;
how to configure the IP Adress of CISCO AIRONET 1600i AP to access It through the Web browser and configure It?
we tried to assign a static IP using CLI so we downloaded Tera Term and tried to connect It using the DB Cable. The following message shows up:
*Mar 1 01:41:43.674: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
we tried to execute 'Enable' command and It works then we tried to execute 'config t' command but failed (the other commands do not work too):
APf07f.06f0.93b5#config t
^ % Invalid input detected at '^' marker.
I connected the Aironet AP to a Router which has 192.168.1.1 as a default IP Adress and thats what shows up on the terminal:
Translating "CISCO-CAPWAP-CONTROLLER.Home"...domain server (192.168.1.1)
*Mar 1 00:34:05.251: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:34:05.255: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.Home
Not in Bound state.
*Mar 1 00:34:50.754: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:34:53.766: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:34:53.830: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.5, mask 255.255.255.0, hostname APf07f.06f0.93b5Hi
By default these AP comes with lightweight image & require a WLC to manage it.(unless you specifically order this AP with autonomous image)
If you want to convert it autonomous (to use without a WLC) then you have to load an autonomous image to it. You should have an image like this (ap1g2-k9w7-tar.153-3.JAB.tar) to begin with (you may require a valid maintenance contract to download this from cisco web site)
Then you can follow one of the methods to convert it to a autonomous AP
1. http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
2. http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/
HTH
Rasika -
Hello,
i have 2 cisco aironet 1300 series configured as root bridge and non root bridge, i managed to configure them and they are associating only when they adjacent , when i separate them them communication fail , could you please help me to solve this . thxThose are very old bridges. So if they are still functioning okay, do they require external antennas or not and do you have external antennas if they do?
Antenna Interface
• AIR-BR1310G-x-K9 or AIR-LAP1310G-x-K9: Air interface (integrated directional antenna)
• AIR-BR1310G-x-K9-R or AIR-LAP1310G-x-K9R: Two RP-TNC type connectors for external antennas
-Scott -
Cisco Aironet 1300 - Coverage area
Hi,
could you please tell me what is the max coverage area that supports on Cisco Aironet 1300 with integrated antenna (13 dbi).Check out the following URLs
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
and
http://www.cisco.com/en/US/products/ps5861/prod_brochure09186a0080230777.html -
I got a Cisco Aironet card to replace the Broadcom that uses ndiswrapper. Here is what happens
modprobe airo
modprobe airo_ca
then run iwconfig
eth1 (which is my wireless card) no wireless extensions
A few places suggested that it is the driver. Anyone have any other suggestions? Does anyone use a Cisco Aironet card? How did you get it installed?i have aironet 350
modprobe
yenta_socket , pcmcia_core , airo , & airo_cs
in rc.conf
lo="lo 127.0.0.1"
#eth0="dhcp"
eth1="dhcp"
INTERFACES=(lo !eth0 eth1)
DAEMONS=(syslog-ng !hotplug pcmcia network netfs crond )
but since the upgrades that came out the other day
it doesnt work at boot up i have to unplug then plugin card
run as root
ifconfig -a
dhcpcd eth1 or i could use
dhcpcd wifi0
from what ive read so far its a udev prob havent been able to figure it out yet
so im plugging away at that -
On the Cisco Aironet 1500 Series Lightweight Outdoor Mesh Access Point spec sheet from the Cisco.com website, it states that the input power for the DC inline POE is 28.5 W at 48 VDC, nominal. What is the maximum power at 48 VDC? On AC, the nominal power is 57.8W at 120 VAC. What is the maximum power at 120 VAC?
Also, I see that the Cisco 1510 only uses AC as a source. Does Cisco have a device for the Cisco Aironet 1510 that uses DC as a source? For example, instead of using the POE Injector that Cisco has, which uses an input of 120VAC (1.5A) and outputs 48VDC (1.2A), does Cisco have a POE Injector that uses an input of 12VDC and outputs 48VDC (1.2A).I think the maximum draw (with both radios and heater on) is 57.8 Watts, but with the heater not active it's much lower around 36.84 Watts.
-
Can a CISCO Aironet 700w be set up as Antonius Access Point ? I was able to set up 700i OK no problem
Need to Set it up for WIFI site Survey Active to test coverageThe 700W series access point contains two simultaneous dual-band radios, the 2.4 GHz and 5 GHz 802.11n MIMO radios, in a controller-based mode.
Source: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/702W/quick/guide/ap702Wgetstart.html -
Cisco Aironet 1200
Firmware 12.3(8)JEB
Hello,
I want to control client associations when AP load is high.
Is there an MIB object that enables/disables client associations?
I have searched the supported MIBS, but i could not find anything.An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Here is the URL which indicate indicates the maximum power levels allowed with the Cisco integrated antenna for each regulatory domain and also contain configuration setting.
http://www.cisco.com/en/US/docs/wireless/access_point/1200/vxworks/installation/guide/higaxd_2.html -
Cisco Aironet 350 series/panel indicator
Cisco Aironet 350
I have the next indicators signals:
Ethernet activity= Steady RED
Association Status=Steady GREEN
Radio Activity=Steady AMBER
I can't use the acces point's serial for management systemHere is a link to the led indicators although your colors aren't shown in the list.
http://www.cisco.com/public/scc/compass/ap/information_files/led_table_wbg.html
Based on the age of the unit, no access to the console, all LEDs are on. I would agree with Scott. It's likely bad ..
Sent from Cisco Technical Support iPad App
Maybe you are looking for
-
Can't log in - desktop won't load
Hi, and thanks for reading this. I hope someone here can help me. I have a G4 flat-panel iMac, running 10.2.8. Bought brand new in 2002 and have had no problems, with the exception of the hard drive going out a few months later and replaced under war
-
Upon exiting LV7: Application Error-Memory could not be read.
Upon terminating my application, I get the following error: "LavVIEW: LabVIEW.exe - Application Error The instruction at referenced memory at . The memory could not be 'read'." So far the error seems non-critical. It does not appear to affect the per
-
Anyone who can help me?
-
CopyProfile fails in unattend.xml - error 0x8007012b
Hello, I am trying to create a Windows 8.1 x64 bit Enterprise image. Upon sysprepping I am getting a copyprofile error (listed below). Normally this is caused by a profile not being deleted out of the registry but I have not deleted or created any pr
-
Problem getting tv shows to go onto ipod.
I have a 5th gen ipod with video and have had for a while now. Whenever I download a new episode for a tv show or buy a season pass then plug my ipod in they all get put onto my ipod. The next time i plug in my ipod and it updates it. When i go to my