Cisco Aironet 1300 series

Hello,
i have 2 cisco aironet 1300 series configured as root bridge and non root bridge, i managed to configure them and they are associating only when they adjacent , when i separate them them communication fail , could you please help me to solve this . thx 

Those are very old bridges. So if they are still functioning okay, do they require external antennas or not and do you have external antennas if they do?
Antenna Interface 
• AIR-BR1310G-x-K9 or AIR-LAP1310G-x-K9: Air interface (integrated directional antenna) 
• AIR-BR1310G-x-K9-R or AIR-LAP1310G-x-K9R: Two RP-TNC type connectors for external antennas 
-Scott

Similar Messages

  • Cisco Aironet 1300 Series Power

    Can the 1310ap receive it's power from a POE switch?

    Hi Edward,
    Sadly the 1310 cannot be powered by PoE ,but, the Power Injector can be up to 100 meters away from the unit.
    Dual coaxial cable to run from the power injector to the 1300. See attached notes:
    Cisco Aironet 1300 Series
    Cisco Aironet 1300 Series Access Point/Bridge Power Injector
    The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
    Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
    Ethernet Ports
    The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
    Power
    The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
    AIR-PWRINJ-BLR2
    F-Type Connectors
    Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
    Hope this helps!
    Rob

  • Cisco Aironet 1300 Series wireless birdge problem

    Hi,
    first one, i'm sorry for my english.
    I have a very big problem with the bridge. I can't configure the nonRoot bridge. It's not possible for me to turn on the radio. The software and hardware are always disable...
    The SSID management is configured with the same SSID.
    For the test, there isn't encryption.
    thanks a lot for your help
    G.Vincent

    Hi,
    Thank you for your answer.
    The root birdge is a 1310G-E-K9-R
    Tne non root bridge is a 1310G-E-K9-R
    To configure the bridge, I have followed the cisco documentation.
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml
    The root configuration:
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname ap
    aaa new-model
    aaa authentication login default local
    aaa authorization exec default local
    aaa session-id common
    dot11 activity-timeout bridge default 1
    dot11 ssid martinshotels
    guest-mode
    infrastructure-ssid
    username Cisco password xxx
    username administrator privilege 15 password xxx
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    ssid martinshotels
    station-role root bridge
    distance 1
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.0.250 255.255.255.0
    no ip route-cache
    ip http server
    ip http authentication aaa
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    bridge 1 route ip
    line con 0
    line vty 0 4
    end
    The non root configuration :
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname apNonRoot
    aaa new-model
    aaa authentication login default local
    aaa authorization exec default local
    aaa session-id common
    dot11 activity-timeout bridge default 1
    dot11 ssid martinshotels
    guest-mode
    infrastructure-ssid
    username Cisco password xxx
    username administrator privilege 15 password xxx
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    ssid martinshotels
    station-role non-root bridge
    mobile station scan 2417
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.0.251 255.255.255.0
    no ip route-cache
    ip http server
    ip http authentication aaa
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    bridge 1 route ip
    line con 0
    line vty 0 4
    end
    Thanks a lot for your help

  • Trouble with Aironet 1300 series

    I have a cisco aironet 1300 series and i need to reset it back to factory default.  the directions say push the mode button while the access point is off and then turn it on while the mode button is down...
    i don't see one button on this thing anywhere.
    help needed

    Hi Jim,
    The 1310 bridge/injector do not have a mode button for configuration reset. However, you can reset the configuration if you use the console port on the injector:
    1) Connect console port and power-cycle unit
    2) When IOS starts loading, hit ESC key twice to get to the boot-loader prompt
    3) At the boot-loader prompt show a directory of the flash filesystem (dir  flash:)
    4) Delete or rename the files "config.txt" and "env_vars", then boot the  system ("delete flash:/config.txt" "delete flash:/env_vars")
    (The default user/pass should be Cisco/Cisco)
    -Patrick Croak
    Wireless TAC

  • Image Recovery for Cisco Aironet 1300 Outdoor Access Point

    We purchased two 1300 APs for outside. There is a new release for the image that we wanted to use so, we have the latest security updates. We downloaded, logged onto the access point just fine, but the image never took. After four hours with a direct connection, it was still going and this morning we came in and it just keep rebooting. Our network guy states it looks like a corrupt image. We can barely do anything and since there is no "mode" button like the earlier models, I have not found anything on web sites or forums to help us reload a good image to the access point. I would appreciate any insight someone has and/or where to look for this. I logged on and downloaded about every manual on the 1300 I could find, but have not found a good way to fix this. Not even the upgrade tool will connect since it just keeps rebooting.

    Hi Bruce,
    Because (as you correctly noted) the 1300 does not have a mode button you could try this method;
    Complete the steps in this section in order to reset Cisco IOS Software-based bridges:
    If the privileged command prompt ap# is available in the CLI, the write erase command and the reload command erase the startup configuration and reset the unit.
    If the GUI is available, choose System Software > System Configuration. Press the Reset to Defaults button.
    Aironet 1300 Series Bridges do not have a MODE button to reset the AP to factory defaults. So, if neither the GUI or CLI is available with sufficient privileges, complete these steps to delete the current configuration and return the entire bridge settings to the factory defaults using the CLI.
    Open the CLI with a Telnet session or a connection to the bridge console port.
    Reboot the bridge by removing and reapplying power.
    Allow the bridge to boot until the command prompt appears and the bridge begins to inflate the image.
    Press ESC when you see lines that are similar to these on the CLI:
    Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"
    ...#############################################################################Note: In order to access the boot loader, you must press ESC twice. But this action depends on the terminal-emulation software that you use.
    Messages that are similar to these appear:
    Error loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_
    ja.20040314"
    Interrupt within 5 seconds to abort boot process.
    Boot process terminated.
    The system is unable to boot automatically. The BOOT environment variable needs to
    be set to a bootable image.
    C1310 Boot Loader (C1310-BOOT-M), Version 12.2 [BLD-v122_15-ja_throttle.20040314 100]
    bridge:At the bridge: prompt, issue the dir flash: command in order to view a directory of the Flash file system.
    The directory is similar to this directory:
    bridge: dir flash:
    Directory of flash:/
    2 -rwx 0 env_vars
    5 drwx 384 C1310-k9w7-mx.v133_15_JA.20040314
    3 -rwx 1128 config.txt
    4 -rwx 5 private-config
    3693568 bytes available (4047872 bytes used)
    bridge:Delete or rename the files config.txt and env_vars, and reboot the bridge.
    Note: Do not forget the / character before the filenames.
    bridge: delete flash:config.txt
    Are you sure you want to delete flash:/config.txt (y/n)?y
    File "flash:/config.txt" deleted
    bridge: delete flash:/env_vars
    Are you sure you want to delete "flash:/env_vars" (y/n)?y
    File "flash:/env_vars" deletedIssue the boot command in order to reboot the bridge at the bridge: prompt, or simply power cycle the bridge.
    After the bridge reboots, reconfigure the bridge with the web browser interface, the Telnet interface, or Cisco IOS Software commands.
    Note: The bridge is configured with the factory default values that include:
    The IP address, which is set to receive an IP address with DHCP. If you do not have a DHCP server, you can access the bridge using the default IP address of 10.0.0.1 using HTTP/HTTPS or Telnet. Once you gain access to the bridge via Telnet or GUI, you can modify the IP address of the bridge.
    Note: This default IP address of 10.0.0.1 becomes available only for a short period. So, make sure that you assign your own IP address to the bridge within that period of time.
    The default username and password, "Cisco".
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#ca_1310_ser
    One other thing, be careful with the new IOS that you aren't loading a LWAPP Recovery Image. (it almost sounds like what may have happened)
    Hope this helps!
    Rob

  • Cisco Aironet 1300 QoS

    Hello, I have 2 Cisco Aironet 1300 Bridges which provide data and voice communication between 2 buildings. Up until recently QoS has not been needed, but lately there appears to be congestion due to reports of poor voice quality. Building A houses a V3000 NBX Telephone system, Building B houses approximately 30 remote IP phones. Building A and Building B are approximately 100 yards apart. No VLAN's. Due to myself being an extreme noob to Cisco bridges, I was hoping some of you may have had experience in setting this up and hopefully provide some tips. I need to prioritize traffic on UDP ports 2093-2096 and TCP port 1040. Thank you in advance for any suggestions. My current running config is below:
    Using 1283 out of 32768 bytes
    version 12.3
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname LHS-WeightRoom-WCV
    ip subnet-zero
    aaa new-model
    aaa authentication login default local
    aaa authorization exec default local
    aaa session-id common
    dot11 ssid wcv
    authentication open
    guest-mode
    dot11 ssid wcvcisco
    authentication open
    infrastructure-ssid optional
    username root privilege 15 password 7 0247335A05320A2244
    username Cisco privilege 15 password 7 074E164D403D1C061F
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    ssid wcv
    ssid wcvcisco
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
    54.0
    station-role root bridge
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    bridge-group 1
    bridge-group 1 spanning-disabled
    hold-queue 80 in
    interface BVI1
    ip address 10.141.8.6 255.255.254.0
    no ip route-cache
    ip default-gateway 10.141.8.5
    ip http server
    ip http authentication aaa
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    control-plane
    bridge 1 route ip
    line con 0
    line vty 0 4
    end

    Here is the URL for the configuration of Cisco Aironet 1300 QoS. Follow the guide it may help you
    http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html

  • Hello,good day problem with Cisco aironet 1040 series acces point

    Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
    if possible please send me step by step instruction, any help is gladly appreciated.
    thank you in advance, More power
    mel

    helo good day sir,
    this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
    i jack the patch cord in and its goes on colored green,
    the thing is how i can configure the aironet 1040  sir?
    waiting for a step by step instruction,
    thank you in advance
    mel

  • Cisco Aironet 1300 - Coverage area

    Hi,
    could you please tell me what is the max coverage area that supports on Cisco Aironet 1300 with integrated antenna (13 dbi).

    Check out the following URLs
    http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
    and
    http://www.cisco.com/en/US/products/ps5861/prod_brochure09186a0080230777.html

  • Problème d'installation d'ios cisco aironet 1300

    au fait j'ai un cisco aironet 1300 et je n'arrive pas à installer l'ios par ce que 'il ne me donne pas la main pour gérer. Au lieu de m'afficher root> il m'affiche que bridge: avec des commandes qui ne permettent pas d'installer l'ios.
    Si vous pouvez m'aider à reinstaller lle système
    Merci d'avance

    Salut mamadou, quand tu es au prompt, tu tapes :
    ether_init
    flash_init
    set IP_ADDR 192.168.133.160
    set NETMASK 255.255.255.0
    set DEFAULT_ROUTER 192.168.133.1
    Mets bien en majuscules et remplaces l'adresse IP le masque et la passerelle par ce que tu veux sur ta borne
    puis tape :
    tftp_init
    tar -xtract tftp://192.168.130.222/images/c350-k9w7-tar.122-13.JA1 flash:
    remplaces l'ip par celle de ton serveur tftp, et le fichier image par celui correspondant à ta borne que tu auras avant copié sur ton serveur tftp
    tu vas voir pas mal de logs, appuie sur entrée ou sur la barre d'espace pour faire défiler
    une fois l'extraction terminée tu tapes
    set BOOT flash:/c350-k9w7-mx.122-13.JA1/c350-k9w7-mx.122-13.JA1
    remplaces c350.... par le nom de ton image
    puis tu tapes boot pour booter ta borne
    A++

  • Cisco aironet 1300 Iphone 3G

    Bonjour
    apres avoir configurer mon routeur cisco aironet 1300 et que la connexion passe tres bien.
    Mais mon probléme en est que je n'arrive a me connecté sur à internet sur mon iphone. la connectivité  entre le routeur et l'iphone pass tres bien.
    et sur d'autres routeurs wifi je peux me connecter avec mon iphone sur internet et tel n'est pas le cas avec mon routeur aironet 1300

    Hi,
    Vous  pouvez essayer de désactiver l'extension Aironet que la désactivation  des extensions Aironet améliore la capacité des machines clientes  non-Cisco de s'associer au dispositif sans fil.
    int dot11 0 or 1
    no dot11 extension aironet
    Link : http://www.cisco.com/en/US/docs/wireless/access_point/12.3_8_JA/configuration/guide/s38rf.html#wp1135928
    Regards,
    Madhuri

  • Cisco aironet 2600 series AP configuration with windows 2008 R2 Radius server.

    I want to know the configuration of Cisco aironet 2600 series AP with windows 2008 R2 Radius server.  
    I have
    1. AD & DHCP Server
    2. Cisco Aironet 2600 Access Point.
    I want to connect wifi devices through this AP. Authentication should be through Radius server and AD.

    Hi , 
    Below link should support your requirement 
    http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116584-configure-wirelesslan-00.html
    Minimal command : -
    AP(config)# aaa new-model
     AP(config)# radius-server host 172.20.0.1 auth-port 1645 acct-port 1645 key XXXXXX
     AP(config)# radius-server deadtime 10
    HTH
    Sandy

  • Cisco Aironet 1310 series

    hello all,
    I have a cisco Aironet 1310 series which am having problem with the signal strength. This box came with 8 dbi Omni antenna gain and am told this can go upto 5km raduis. After configuring this equipment, i could not get a link when i move 500 meters. Please find attached the configs on the box. Any help given would be very much appreciated. Thank You

    This 5KM distance is only going to be applicable in bridging situations. The following link shows how to use the distance calculations based on devices: http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
    In theory, if you had a really strong direction antenna on your client you'd be able to get the 1310 as an access Point from 5km, but you'd need perfect line-of-site and you wouldn't be mobile...
    As others had mentioned, if you're looking for an access point situation with that kind of range, then you need WiMax....
    but if it is bridging you want, its just a matter of getting the other link to see this one (with a good enough antenna)

  • Cisco Aironet 1100 series wireless access point software update!

    Hi,
    I have a wireless network using 2 cisco aironet 1100 series access points.
    From time to time I have problems with connecting a device (Laptop,PC,)to the wireless network.There are onther wireless netwotk that operate around and might be using the same channel.Someone else created the wireless network and I do not know how to access it now to check the configurations on change something.
    I cannot conncet my iPhone to the network and I beleive that a software update might solve the problem but I do not know how to do it and where to download it from.
    1. How can I update the software and where from?
    2.How can I ensure that thare are no interferences and conflicts?
    3.How can I ensure that no onther wireless network around is using the same channel?
    Thank you in advance.

    Sounds good to me. Are you having problems?
    Please remeber to rate all replies

  • Cisco aironet 1200 Series access point dropping clients

    We are having an issue where our Cisco Aironet 1220 Series AP is constantly dropping clients. We have 3 APs mounted on a single tower, all out of each others range and freq. There are approximatly 30 clients on each AP. We are noticing an increase in dropped customers (up to 20 at a time). ANy suggestions? This only became an issue in the last few weeks, and nothing major has changed.

    Hi
    Even I was facing almost the same kind of problem. But in my case it was wired clients to the workgroup bridge 350.
    I had done lot of testings and reading at that time to resolve this problem.
    However in your case I feel your problem can be resolved by keeping the option "Reliable multicast for Workgroup bridges" disabled in the APs under dot11radio interface settings. This is possibly because the radios cannot associate to more than 20 clients at a time if the option is in the enable mode.
    You need to keep this option enabled in a root bridge when you have problems of dropping the wired clients to the workgroup bridge.
    By keeping this option enabled, you are actually asking the Root bridges to consider the Workgroup bridges as Infrastructure devices and not as clients thereby making the roots to send all the multicasts to the WGBs. However in that case it losses the efficiency of associating more than 20 clients.
    Let me know if this resolves your problem.
    Regards

  • Aironet 1300 series as wireless client ?

    Hi there.
    I would like to install a device on a yacht so that when the yacht enters a marina, it can connect to the marina wifi and then make that connection available to the yacht network. I am looking for a cisco device that will do similar to the Smartbridge Nexus (http://www.smartbridges.com/products/accesspoints.asp), which have done the job adequately in the past.
    I was thinking of using a 1300 series outdoor unit, does anyone know if I can use it in the way I plan, or if there is an alternative.
    Many thanks,
    Neil

    There are couple of options for you.
    1. Cisco 350 series workgroup bridge - this will connect to the marina wi-fi and provide wired access to the yacht. If you connect a hub to the WGB's output, you can spread the connection among multiple laptops.
    2. Also explore an option of using any Cisco AP as a repeater. A repeater will connect to the marina wi-fi wirelessly and extend the network to the yacht. But please note that the data rate may not be that good because of an extra hop in the middle.
    For both these options to work, the marina wi-fi must be autonomous AP deployment based. If it is a lightweight-based wi-fi with a controller none of these options will work.
    HTH

Maybe you are looking for