Cisco Aironet 1400 Series EoL

Hi all, what is the replacment model for the eol 1400 series Ap's that I need to purchase?
Thanks
Martyn

Kindly review the below link:
http://www.exaltcom.com/uploadedFiles/003_-_Products/005_-_Data_Sheets/DS-Cisco-ExtendAir-r5005-B-1010.pdf

Similar Messages

Hello,good day problem with Cisco aironet 1040 series acces point

Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
mel

helo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040 sir?
waiting for a step by step instruction,
thank you in advance
mel

Cisco Aironet 1300 series

Hello,
i have 2 cisco aironet 1300 series configured as root bridge and non root bridge, i managed to configure them and they are associating only when they adjacent , when i separate them them communication fail , could you please help me to solve this . thx

Those are very old bridges. So if they are still functioning okay, do they require external antennas or not and do you have external antennas if they do?
Antenna Interface
• AIR-BR1310G-x-K9 or AIR-LAP1310G-x-K9: Air interface (integrated directional antenna)
• AIR-BR1310G-x-K9-R or AIR-LAP1310G-x-K9R: Two RP-TNC type connectors for external antennas
-Scott

Cisco Aironet 1300 Series Power

Can the 1310ap receive it's power from a POE switch?

Hi Edward,
Sadly the 1310 cannot be powered by PoE ,but, the Power Injector can be up to 100 meters away from the unit.
Dual coaxial cable to run from the power injector to the 1300. See attached notes:
Cisco Aironet 1300 Series
Cisco Aironet 1300 Series Access Point/Bridge Power Injector
The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
Ethernet Ports
The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
Power
The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
AIR-PWRINJ-BLR2
F-Type Connectors
Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
Hope this helps!
Rob

Cisco aironet 2600 series AP configuration with windows 2008 R2 Radius server.

I want to know the configuration of Cisco aironet 2600 series AP with windows 2008 R2 Radius server.
I have
1. AD & DHCP Server
2. Cisco Aironet 2600 Access Point.
I want to connect wifi devices through this AP. Authentication should be through Radius server and AD.

Hi ,
Below link should support your requirement
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116584-configure-wirelesslan-00.html
Minimal command : -
AP(config)# aaa new-model
AP(config)# radius-server host 172.20.0.1 auth-port 1645 acct-port 1645 key XXXXXX
AP(config)# radius-server deadtime 10
HTH
Sandy

Cisco Aironet 1310 series

hello all,
I have a cisco Aironet 1310 series which am having problem with the signal strength. This box came with 8 dbi Omni antenna gain and am told this can go upto 5km raduis. After configuring this equipment, i could not get a link when i move 500 meters. Please find attached the configs on the box. Any help given would be very much appreciated. Thank You

This 5KM distance is only going to be applicable in bridging situations. The following link shows how to use the distance calculations based on devices: http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
In theory, if you had a really strong direction antenna on your client you'd be able to get the 1310 as an access Point from 5km, but you'd need perfect line-of-site and you wouldn't be mobile...
As others had mentioned, if you're looking for an access point situation with that kind of range, then you need WiMax....
but if it is bridging you want, its just a matter of getting the other link to see this one (with a good enough antenna)

Cisco Aironet 1100 series wireless access point software update!

Hi,
I have a wireless network using 2 cisco aironet 1100 series access points.
From time to time I have problems with connecting a device (Laptop,PC,)to the wireless network.There are onther wireless netwotk that operate around and might be using the same channel.Someone else created the wireless network and I do not know how to access it now to check the configurations on change something.
I cannot conncet my iPhone to the network and I beleive that a software update might solve the problem but I do not know how to do it and where to download it from.
1. How can I update the software and where from?
2.How can I ensure that thare are no interferences and conflicts?
3.How can I ensure that no onther wireless network around is using the same channel?
Thank you in advance.

Sounds good to me. Are you having problems?
Please remeber to rate all replies

Cisco aironet 1200 Series access point dropping clients

We are having an issue where our Cisco Aironet 1220 Series AP is constantly dropping clients. We have 3 APs mounted on a single tower, all out of each others range and freq. There are approximatly 30 clients on each AP. We are noticing an increase in dropped customers (up to 20 at a time). ANy suggestions? This only became an issue in the last few weeks, and nothing major has changed.

Hi
Even I was facing almost the same kind of problem. But in my case it was wired clients to the workgroup bridge 350.
I had done lot of testings and reading at that time to resolve this problem.
However in your case I feel your problem can be resolved by keeping the option "Reliable multicast for Workgroup bridges" disabled in the APs under dot11radio interface settings. This is possibly because the radios cannot associate to more than 20 clients at a time if the option is in the enable mode.
You need to keep this option enabled in a root bridge when you have problems of dropping the wired clients to the workgroup bridge.
By keeping this option enabled, you are actually asking the Root bridges to consider the Workgroup bridges as Infrastructure devices and not as clients thereby making the roots to send all the multicasts to the WGBs. However in that case it losses the efficiency of associating more than 20 clients.
Let me know if this resolves your problem.
Regards

How to load a boot image to cisco aironet 1140 series after missing boot image

Hi all,
I need a solution for this. When i switch my cisco aironet 1140 , it s blinking with red light .and gives a message "no boot image to load".
When i tried next time, by pressing escape it shows this message that i have mentioned below.
ap:
ap:
using eeprom values
WRDTR,CLKTR: 0x83000800 0x40000000
RQDC ,RFDC : 0x80000035 0x00000208
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0x40000000
RQDC, RFDC : 0x80000035, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialized
PCIEx: initialization done
flashfs[0]: 1 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 1536
flashfs[0]: Bytes available: 32383488
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 28:94:0f:d6:c8:62
Ethernet speed is 100 Mb - FULL duplex
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Tue 18-Oct-11 14:51 by prod_rel_team
ap:
So , now my question is how to load the boot image ? From where will we get this ? OR
I m also having another Cisco aironet 1140 , Can i get bootimage from that . Kindly let me know the solution from genius ?

Take a look at this link as it should have the info you need
https://supportforums.cisco.com/docs/DOC-14636
Sent from Cisco Technical Support iPhone App

Cisco Aironet 350 series/panel indicator

Cisco Aironet 350
I have the next indicators signals:
Ethernet activity= Steady RED
Association Status=Steady GREEN
Radio Activity=Steady AMBER
I can't use the acces point's serial for management system

Here is a link to the led indicators although your colors aren't shown in the list.
http://www.cisco.com/public/scc/compass/ap/information_files/led_table_wbg.html
Based on the age of the unit, no access to the console, all LEDs are on. I would agree with Scott. It's likely bad ..
Sent from Cisco Technical Support iPad App

Question regarding the use of Cisco Aironet 1140 series

We are looking at deploying some of the Cisco Aironet Access Points as standalone. We are essentially setting up a hotspot. They will mainly be in conference rooms at each of our field offices so visitors attending our meetings can have internet access. Do clients have to use Cisco wireless adapters in order to connect
to any of Cisco Aironet Access Points or can they use whatever wireless card they have as long as it supports the bands available?
Thx in advance for any advice given.

Any product which displays the Wi-Fi Certified logo, including everything from Cisco, should interoperate with any other Wi-Fi Certified gear.

Configuration of cisco aironet 1260 series access point..??

i hv a cisco aironet 1262n access point and a normal router(without wlan) with a broadband connection
now i want to use my access point as a wifi hotspot
but i am not able to access it, through web browser
i dont know how i connect wires so that i am able to access " AP access page" and also i forgot its IP address too so can u pls tell me how do i reset it to default

Your AP is most likely loaded with a controller-based IOS. You can easily convert this to autonomous IOS.
Read this: Using a TFTP Server to Return to a Previous Release

Cisco Aironet 1400 - security

Dear all,
I'm currently configuring 2 Cisco 1400 Bridges. One is the root bridge the other the non-root bridge (ok logic :-) ).
I wanted to know what is possible for using certificates for the non-root bridge or to use the local radius on the root bridge to increase the security level of the wlan network.
I tried to reach the local radius on the root bridge, but I'm always getting a 404 error. After reading some Cisco docs, it said that we need to use AAA new model from the CLI, I did it without success.
What would you recommend to ensure a good security level for the wireless link?
I'm open to use certificates or a Radius (local or IAS) or any suggestions you may have.
Any help or or suggestions are very welcomed...
Thanks per advance,
Regards

The only EAP types supported by BR1410 is LEAP. You should able to configure LEAP client on the non-root bridge:
http://www.cisco.com/en/US/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15rep.html#wp1036921
The above URL is for repeater; however, it is the same for non-root bridge.
You may already know. If you want to set up local radius server, the following URL should be useful:
http://www.cisco.com/en/US/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15local.html

Cisco Aironet 1200 series AP's...

Hi,
The wireless at one of our remote sites was working fine until there was a problem one week back. Just for introduction we are using the following setups for wireless:
independent wireless access-points whihc connect directly to the Cisco switches most 2950's..
We have three vlans in LAN, vlan1 (for user - LAN), vlan-4 (for wireless users - EAP auth with MS-IAS s radius) and vlan-5 (for wireless scanners - MAC auth).
All the AP's are 1231G series of devices.
These AP's are connected to the switchports with a trunk, dot1Q enabled, vlan-4 as native vlan.
Suddenly one day, 12 out of 15 AP's went offline, meaning: we were not able to ping any of them except 3 which were working fine. When checked at the switch we were able to see all 15 of them as CDP neighbor of the switches, even the ones which were not able to be pinged on the network. We were not able to ping them neither from the local L2 switch (IP on vlan-1) nor from the site router (default gateway of all the local subnets).
I took the console connection of one of the not-working AP, it does not show any particular log or message. The Fastethernet0 port was UP/UP. I was not able to ping AP's default gateway. When I rebooted the AP, it was pinging from the network for about 2 mins and after that it was again off-network, not pinging. When the AP was reset to factory default, it was pinging fine for a long time, without any problems. When we put in the OLD configuration, again it was off-network, not pinging.
Now, here is the surprising element for me! After 3 days of struggled troubleshoooting, remotely, onsite engineer changed the vlan allowed on the WAP connected trunk switchports (ie switchport trunk allowed vlan 4,5) i.e previously we were allowing 1, 4 and 5 vlans on the trunk, now he is allowing only 4 and 5. As soon as he made the changes, all of the not-working 12 WAP's became online one by one (as and when config change made on the trunk). Just to make another test and to make sure, I tried to allow all the vlans again and guess what the WAP was again off-networ - not pinging.
Now my question is: Why it was all working fine for more than a year and then suddenly one day 'something' happened which caused the 12 AP's to behave abnormal while 3 of them were still working good.
Is there any technical theory which can explain such type of behaviour?
Thanks in advance,
Gaurav

Gaurav,
If you have the ability to, I would put on AP back to the "non-working" scenario. then check the ARP table to see if you are getting a duplicate mac or IP address.
HTH,
Steve
Please remember to rate helpful posts or to mark the quesiton as answered so that it can be found later.

Cisco Aironet 1300 Series wireless birdge problem

Hi,
first one, i'm sorry for my english.
I have a very big problem with the bridge. I can't configure the nonRoot bridge. It's not possible for me to turn on the radio. The software and hardware are always disable...
The SSID management is configured with the same SSID.
For the test, there isn't encryption.
thanks a lot for your help
G.Vincent

Hi,
Thank you for your answer.
The root birdge is a 1310G-E-K9-R
Tne non root bridge is a 1310G-E-K9-R
To configure the bridge, I have followed the cisco documentation.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml
The root configuration:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 activity-timeout bridge default 1
dot11 ssid martinshotels
guest-mode
infrastructure-ssid
username Cisco password xxx
username administrator privilege 15 password xxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid martinshotels
station-role root bridge
distance 1
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.250 255.255.255.0
no ip route-cache
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end
The non root configuration :
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname apNonRoot
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 activity-timeout bridge default 1
dot11 ssid martinshotels
guest-mode
infrastructure-ssid
username Cisco password xxx
username administrator privilege 15 password xxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid martinshotels
station-role non-root bridge
mobile station scan 2417
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.251 255.255.255.0
no ip route-cache
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end
Thanks a lot for your help

Cisco Aironet 1400 Series EoL

Similar Messages

Maybe you are looking for