Cisco Aironet 1410 Multipoint with Aironet 1310's

Hello,
We are currently expanding our wireless deployment that consists of two Aironet 1310's bridged together. We would like to hit an area in the opposite direction that is not too far away. Would replacing the 1310 in the root point with a 1410 as the root to provided point to multipoint be a feasible solution? This would make the 1410 the root bridging to two 1310's at opposite ends.
Thank you,
Rick

Hi,
Its not possible to MIX 1410 and 1310 together.. Since 1410 comes with A radio and 1310 comes with G radio and both are not compatible with each other!!
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Similar Messages

OfficeExtend with Aironet 600

Hello,
I need information about the Aironet 600 access point.
I got a customer who want to deploy a guest WLAN on branch office with an authentication with a captive portal that is centralized. I would like to use the OfficeExtend functionnality with Aironet 600 Acces point & WLC 5508 or 2504 to centralize the traffic from all access points on the controller.
On those branch offices, there were a few "free access desktops" that need a copper link. I want those devices to be also authenticated by captive portal, so I want to connect them on the four 10/100 port of the access point. But it seems that we can only use one port as "corporate remote LAN", the threee others are just for "home LAN". Is it correct ?
Is there any solution to configure the four ports as remote LAN interface ?
Thanks a lot for your help

Hi, I'd actually go after HREAP instead of Office Extend. OE is designed for a home user, so you can plug in a phone, or one machine.
HREAP will give you centralized wireless for the guest with the webauth page, and can drop the local traffic to the wire as well.
For the wired guest, I would recommend using 802.1x with fallback to guest. Look here
http://www.cisco.com/en/US/docs/ios/12_4t/12_4t11/ht_8021x.html
This allows the port to be put in a "Guest VLAN" that you can then direct to a authpage. This would require a tertiary device for the wired guests.
it may be more than you are really looking for, but IMO is the best answer to the situation.
HTH,
Steve

Using DHCP Option 60 with Aironet APs

Hello,
I'm trying to configure Aironet 1000 series and Aironet 1130 series APs to talk to a wireless controller card inside a 2811 ISR. I have a Catalyst 3550 L2/L3 Switch between my APs and the 2811. So far the Aironet 1000 series found the wireless controller successfully. The following is the current configuration for the 3550 DHCP pool:
ip dhcp pool WLAN_CM
network 172.27.2.0 255.255.255.0
option 60 ascii "Airespace.AP1200"
default-router 172.27.2.1
option 43 ascii "172.27.3.12"
I would like to add another option 60 statement to be able to connect the Aironet 1130 AP. Would this configuration work?:
ip dhcp pool WLAN_CM
network 172.27.2.0 255.255.255.0
option 60 ascii "Airespace.AP1200"
option 60 ascii "Cisco AP c1130"
default-router 172.27.2.1
option 43 ascii "172.27.3.12"
I will try shortly in the lab. I am not sure if I need to create another DHCP pool entirely dedicated for the 1130.
Any input will be much appreciated.

Hello
why do you use option 60?
From my view, the AP needs just to know option 43 to find the controller, but the problem is that the airespace-ap wanna have option 43 in ascii and ios-ap in lwapp mode wanna have the option in hex.
best regards
Oliver

Cisco SSL-VPN / webvpn with Cisco 2901 IOS 15.3.3M

Dear Community,
I have a strange issue that I am hoping some of you will be able to assist with.
I am running an environment with the following specifications
Cisco ISR G2 2901 with IOS 15.3.3M
Security Licence enabled
Data Licence enabled
VPN Licence enabled
Cisco ISR G2 2951 with IOS 15.3.3M
Security Licence enabled
Data Licence enabled
SM with ESX server.
Desktop Environment
Windows XP SP3
Internet Explorer 8
Desktop Environment 2
Windows 8
Internet Explorer 10
I have a ESX server set up with a web page on the 2951. The 2901 unit has a SSL VPN / web vpn service set up on it to allow the Desktop Environments to connect to the 2951 web page. The Desktop Environments are not allowed to directly connect to the 2951 router that is why the SSL-VPN / web vpn is used.
This system was initially working with IOS 15.2.4M2 however an update of the IOS was required and now the VPN does not fully function correctly.
PROBLEM: Now the webvpn interface loads with the welcome screen and login. After logging in it has a screen with a link to the webpage on the 2951. When I try open this webpage on the 2951 and the SSL-VPN starts to build I only get half my web page. There seems to be a problem where I only get half a page loading or just a blank page with just HTML headers. I have tried changing the page to just HTML but it still does not display properly. This is with Internet Explorer ( all versions ). With firefox there are no problems but I cannot run this browser as my environment will not allow it.
If anyone can assit me here it would really make my day.
Thanks,
Will

Can anyone help with this ?

Reader v11 Update fails on Windows Vista (entire network) with error 1310

Tried to run the Reader v11 updater after installing v11. It fails comsistently with error 1310, although the file in the error message is different each time. The file is usually, but not always, in the folder config.msi.
We had this problem in the Reader v10 updaters as well, however we traced it to a race condition in file handling. We could get it to install by running other programs concurently or disabling anti-virus, to alter the timing of the install. Usually it took 3 to 6 attempts for it to complete successfully.
With the v11 updater, no amount of iterations will get it to install. We've tried upwards of 20 times. We've also tried re-installing v11 and then applying the update over a fresh copy. That does not work either. The usual tricks that worked with v10 also do not work with v11.
This problem could be solved easily if the updater would prompt the user for a retry on error, instead of automatically rolling back. For the main installer, the user is prompted to retry, but not for the updater. We run plenty of installers in the school without problems, but the Reader updates are always difficult.
We have wasted dozens of hours on this in our school. We are supposed to keep the Reader patched to avoid the significant vulnerabilities it introduces, but we cannot get the updater to run. If anyone else has solved this problem please let us know.

Lorraine, I posted a question in the Adobe Reader forums about the
problems we have with the updaters. I got back this response, they
are blaming it on other software and the Windows Installer. I think
that can't be true, we install all kinds of stuff without problems.
So I think the truth is they've done a crappy job on their updaters.
The latest update is for an extremely serious vulnerability, it's
active in the wild and has made the national news. So if we can't
install the update, then I think we have to move away from Adobe
altogether, to another reader.
Can you think of any reason not to do this?

Cisco ISE Vs Cisco Anyconnect Posture module with Advanced Endpoint Protection

We are planning to use cisco Anyconnect posture module with Adv Endpoint protection to examine the VPN users- This can check whether they a antivirus/anti spyware software installed on their work station and can force to update def file if its older than specified number of days, it can also check the firewall status on their workstation and enable if its not already.This can detect keylogger and emulation softwares also.
Do we get any additional advantages in using ISE compared to Anyconnect posture module ......
Siddhartha

These are good questions. We had them last year before we decided to purchase ISE, specifically for our VPN users.
I will be watching this thread to see what kind of responses you get.
As of right now, I can verify the ISE can indeed check if specific Anti-Virus is installed (i.e., your corporate AntiVirus), or if ANY (supported by Cisco within ISE) antivirus is installed, and it can force an update process for the AV if it detects that the DAT files are older than a admin specified amount of time.
Our issue at the moment (if you haven't searched the forums) is ISE detected the proper WSUS updates are indeed installed on the users systems and allowing the users system to talk to our internal WSUS server.
We are now wondering if the Advanced Endpoint licensing on the ASA would have been a better way to go.
Wishing you luck in finding your answers for us all.
Dirk

Point to multipoint with AP 1230AG

Hello,
I want to do this configuration:
Site A must be connected to site B and to site C. On the site A there is an AP 1230AG, it's configured in bridge mode in point to multipoint to site B and C in 802.11A.
On the site B there is an AP 1230AG, it's configured in bridge mode in point to point to the site A in 802.11A, and it's configured in access point in 802.11G for laptops.
On the site C there is an AP 1230AG, it's configured in bridge mode in point to point to the site A in 802.11A, and it's configured in access point in 802.11G for laptops.
I believe that it's possible to make bridge and access point on the same AP in point to point , but is it possible in point to multipoint with AP 1230AG?
Thanks and regards.

As long as there are dual radios each radio can be configured as both as access point and brdige mode.

Configuring Cisco Router for use with Syslog Server

Configuring Cisco Router for use with Syslog Server:
Does anyone know of a good doc for this?
-Ashley

Start with that one: http://security-planet.de/wp-content/uploads/2008/12/logging-ios.pdf
And if you need more informations, just ask what you want to achieve.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Cisco 5508 Wireless Controller with Splash Page Disclaimer

How do one configure a splash disclaimer page on a Cisco Wireless Controller 5508 with no authentication?
Jimmy

There are many options to you in this scenario, but if you're looking to simply provide a splash page via the WLC without interacting with any other web servers, you can configure Local Web Authentication (LWA) as seen in this configuration example.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html?referring_site=RE&pos=1&page=http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71881-ext-web-auth-wlc.html
If you are not wanting the authentication, you can choose the "passthrough" method which will not require any credentials, only accepting an AUP or whatever you want.

Can i use a cisco RE1000 range extender with airport extreme

Can I use a Cisco R1000 range extender with airport extreme?

Apple's "extend a wireless network" function appears to be a proprietary feature that will only work with other Apple routers.
As far as we know, devices from other manufacturers are not compatible with this feature.
Bottom line....It would be extremely unlikely that this would work, but it's worth a try if you already have the products in hand.
Please post on your results.

Cisco Catalyst 4507R+E with WS-X4748 blade, ports not working

I have a Cisco Catalyst 4507R+E (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade. Has anybody else seen anything like this?

I have 2 Core switches, single SUP on each.
Line cards #1 and #2 randomly stop forwarding packets, only solution is to reload the switch ( hw-module reset does not work ). I have cat4500e-universalk9.SPA.03.05.00.E.152-1.E.bin and the sympton looks the same as the described one,
although the code is newer than 3.2.2SG.
Now we are downgrading to cat4500e-universalk9.SPA.03.04.02.SG.151-2.SG2.bin to check if that solves the issue,
otherwise we´ll try removing/re-inserting the modules, and if issue persists, most probably RMA the Core1.
We´ve sent a show tech to Cisco support while the issue was happening.
Current modules on the Core switches.
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1627L48B
2    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1629L0ZY
3     4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1629L1PD
5    12 1000BaseX (SFP)                        WS-X4612-SFP-E     JAE163007EO
M MAC addresses                    Hw Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
1 30f7.0d57.80c0 to 30f7.0d57.80ef 1.1                               Ok
2 30f7.0dac.fd40 to 30f7.0dac.fd6f 1.1                               Ok
3 30f7.0dca.6c00 to 30f7.0dca.6c03 2.1 15.0(1r)SG10 03.05.00.E       Ok
5 a493.4c44.13e8 to a493.4c44.13f3 1.1                               Ok
Mod Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+----------------------------------
3   Active Supervisor   SSO                 Active

Cisco MDS 9148 compatibility with Finisar FTLF-8524-P2BNV SFP+

Hello,
I have a Cisco MDS 9148 switch with Finisar FTLF-8524-P2BNV SFP+ modules. I am told by the guys configuring the equipment that these modules are not identified in the switch interface.
I am curious if there could be a compatibility problem (I have not found a compatibility list) or any other issue which could cause the behaviour.
Thank you

Integration of CISCO PRIME 1.3 with ACS 5.2

Hi
we are trying to integrate the CISCO PRIME 1.3 with ACS5.2 .We have configured the attribute for admin users in ACS shell profile.
virtual-domain0=ROOT-DOMAIN
total task is 159
After then configured a rule in default device admin.
Default Device Admin> Authorization>
Shell profile is choosen
Command set is full acess.
but not able to get the access of PI .

Please check the below link which may be helpful for you:
Link-1
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.2/configuration/guide/ctrlcfg.html

Cisco Twinax Cables Compatibiltiy with EMC VNX/VNXe

Hi,
I would like to know about Cisco Twinax Cables Compatibiltiy with EMC VNX/VNXe series storage - for connectivity between UCS Fabric Interconnect and EMC VNX/VNXe.
Are the following Cisco Twinax Cables compatible with EMC's VNX and VNXe serie platforms:
SFP-H10GB-CU1M= 1-m 10G SFP+ Twinax cable assembly, passive
SFP-H10GB-CU3M= 3-m 10G SFP+ Twinax cable assembly, passive
SFP-H10GB-CU5M= 5-m 10G SFP+ Twinax cable assembly, passive
SFP-H10GB-ACU7M= 7-m 10G SFP+ Twinax cable assembly, active
SFP-H10GB-ACU10M= 10-m 10G SFP+ Twinax cable assembly, active
Kindly advice. Thanks.

Hi,
I'd like to confirm you, that passive assembly is supported. Haven't tried the actives one yet.
I'm using UCS-B200 M3, and EMC VNX 5300.
the EMC VNX5300 (Block Level) connected using 2 type of media. Copper (SFP-H10GB-CU5M= 5-m 10G SFP+ Twinax cable assembly, passive) and Fiber Channel 8 GB directly info Fabric Interconnect 6248 ports.
For old server the connection is via iSCSI 10GB Copper. and for UCS-B200 M3 is via FC 8GB.
All my configuration is running well.
Hope thats helped.
Thanks,
Pieter

Configuring Cisco ACS 5.1 with Juniper Netscreen Firewall wit Radius & Tacacs+

Hello,
Can anybody tell me the step-by-step configuration of Cisco ACS 5.1, to configured it with Juniper Netscreen Firewall for radius & tacacs+ authentication and authorization?
I am able to configure this with Cisco ACS 4.2 with customise VSA file but can't understand how to configure it on ACS 5.1.
Thanks in Advance.

Hi Eduardo,
Can you tell me how to map ACS 4.2?
service=junos-exec
local-user-name=Engineering
Into the new "shell profiles" on ACS 5.2? How do I verify these attributes are passed onto ACS 5.2? I don't have access to a sniffer or tap nor do I have writes on this box. I have to instruct our systems folks to investigate. It has been a back and forth battle.
Also, I'd like to see where I'd map this on ACS 5.2. Keep in mind in both cases I have a JUNOS config mapping to a login user Engineer and operations respectively.
local-user-name=opertions
allow-commands=((^ping *)|(^mtrace *)|(^traceroute *)|(^monitor *))
deny-commands= ((^start *)|(^file delete *)|(^file rename *)|(^request *)|(^set cli restart-on-upgrade *)|(^set cli prompt *)|(^set chassis *)|(^set date *)|(^test *)|(^clear *)|(^op *))

Cisco Aironet 1410 Multipoint with Aironet 1310's

Similar Messages

Maybe you are looking for