Cisco Aironet 1510
On the Cisco Aironet 1500 Series Lightweight Outdoor Mesh Access Point spec sheet from the Cisco.com website, it states that the input power for the DC inline POE is 28.5 W at 48 VDC, nominal. What is the maximum power at 48 VDC? On AC, the nominal power is 57.8W at 120 VAC. What is the maximum power at 120 VAC?
Also, I see that the Cisco 1510 only uses AC as a source. Does Cisco have a device for the Cisco Aironet 1510 that uses DC as a source? For example, instead of using the POE Injector that Cisco has, which uses an input of 120VAC (1.5A) and outputs 48VDC (1.2A), does Cisco have a POE Injector that uses an input of 12VDC and outputs 48VDC (1.2A).
I think the maximum draw (with both radios and heater on) is 57.8 Watts, but with the heater not active it's much lower around 36.84 Watts.
Similar Messages
-
Sub-option code for a Cisco Aironet 1510 AP
What is the sub-option code that has to be delivered as part of a DHCP Option 43 response for a Cisco Aironet 1510 AP?
Thanks,
Adriani think you're looking for the following:
option 43 ascii
ie:
option 43 ascii "10.10.10.2, 10.10.11.2"
please see this link for more info:
http://www.cisco.com/en/US/products/ps6548/products_quick_start09186a00806b5d00.html#wp45319 -
Hi everybody.
I was reading about cisco aironet 1510 AG and found it has two N series connector for antenna.
Cisco Aironet 1510AG
Expansion / Connectivity
Interfaces
1 x network / power - Ethernet 10Base-T/100Base-TX ¦ 2 x antenna - N-Series connector
1) we have two N series connector for antenna why do we need two antenna?
thanks and have a great weekend.Hi,
Two Antennas are used for diversity. Because there are too many factors that may affect the RF signal (Refraction, reflection, etc), the signal will follow different pathes to reach the destination (called multipath). Having two antennas to send/receive will make the receiver hear two signals (or more). If one of the signals is malformed then error correction will be better this way. This will make it faster than requesting the re-transmit again from the sources.
802.11n access poins usually have 3 Antennas for each radios because they use MIMO.
Also, this link will give you better information about Diversity and Multipath distortion:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008019f646.shtm
HTH
Amjad -
Client association between RAPs & MAPs (Cisco Aironet 1510)
How do you fix the association bugs that the 1510s have?
My problem is when a client (like a laptop) associates to the MAP (Mesh Access Point) or RAP (Rooftop Access Point), the client doesn't hand off it's wireless connection to the access point with the better signal strength. Is there a setting or configuration on the Wireless LAN Controller that would help this problem?There are no issues roaming between RAP. Try upgrading the code of WLC to 4.0.179.8 and also try upgrading the client software since it is the client which should to access point with better signal.
-
How to change default admin password on Cisco Aironet 1040
How do I change the default username and password on the Cisco Aironet 1040. There is a default set and I want to change that to secure the device. I've checked the manual and can't seem to find the directions. Any ideas?
Hi Brian,
If this AP is already registered with a WLC then you can change it via WLC.
In WLC GUI, go to Wireless -> Select the AP -> Credential -> Override Global Credential-> Update username/pw/enable pw
In WLC CLI, you can configure it like this. If it is for all APs, then select all, otherwise AP name.
(WLC3) >config ap mgmtuser add username admin password Cisco123 secret Cisco123 ?
all Applies the configuration to every AP that does not have a specific user name.
Enter the name of the Cisco AP.
(WLC3) >config ap mgmtuser add username password secret
(WLC3) >save config
Are you sure you want to save? (y/n) y
If it is Autonomous AP you can configure using the "username xxxx password xxx" IOS command
HTH
Rasika
*** Pls rate all useful responses **** -
How many users are supported on a Cisco Aironet 1141N? 30?
I have a client that wants to upgrade his Aironet 1131 APs with 1141N. How many users are supported on a Cisco Aironet 1141N?
Yes, you could have 30 clients on the AP.
Client density all depends on what the client is doing, really.
So if you have clients that are just web surfing and pulling email 30+ isn't a problem. If they are all streaming video, then you want to plan for less clients per AP, and more APs.
Steve -
How to load a boot image to cisco aironet 1140 series after missing boot image
Hi all,
I need a solution for this. When i switch my cisco aironet 1140 , it s blinking with red light .and gives a message "no boot image to load".
When i tried next time, by pressing escape it shows this message that i have mentioned below.
ap:
ap:
using eeprom values
WRDTR,CLKTR: 0x83000800 0x40000000
RQDC ,RFDC : 0x80000035 0x00000208
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0x40000000
RQDC, RFDC : 0x80000035, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialized
PCIEx: initialization done
flashfs[0]: 1 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 1536
flashfs[0]: Bytes available: 32383488
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 28:94:0f:d6:c8:62
Ethernet speed is 100 Mb - FULL duplex
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Tue 18-Oct-11 14:51 by prod_rel_team
ap:
So , now my question is how to load the boot image ? From where will we get this ? OR
I m also having another Cisco aironet 1140 , Can i get bootimage from that . Kindly let me know the solution from genius ?Take a look at this link as it should have the info you need
https://supportforums.cisco.com/docs/DOC-14636
Sent from Cisco Technical Support iPhone App -
Hello, I have 2 Cisco Aironet 1300 Bridges which provide data and voice communication between 2 buildings. Up until recently QoS has not been needed, but lately there appears to be congestion due to reports of poor voice quality. Building A houses a V3000 NBX Telephone system, Building B houses approximately 30 remote IP phones. Building A and Building B are approximately 100 yards apart. No VLAN's. Due to myself being an extreme noob to Cisco bridges, I was hoping some of you may have had experience in setting this up and hopefully provide some tips. I need to prioritize traffic on UDP ports 2093-2096 and TCP port 1040. Thank you in advance for any suggestions. My current running config is below:
Using 1283 out of 32768 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LHS-WeightRoom-WCV
ip subnet-zero
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 ssid wcv
authentication open
guest-mode
dot11 ssid wcvcisco
authentication open
infrastructure-ssid optional
username root privilege 15 password 7 0247335A05320A2244
username Cisco privilege 15 password 7 074E164D403D1C061F
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid wcv
ssid wcvcisco
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
54.0
station-role root bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 10.141.8.6 255.255.254.0
no ip route-cache
ip default-gateway 10.141.8.5
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
endHere is the URL for the configuration of Cisco Aironet 1300 QoS. Follow the guide it may help you
http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html -
Hello,good day problem with Cisco aironet 1040 series acces point
Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
melhelo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040 sir?
waiting for a step by step instruction,
thank you in advance
mel -
Hello;
how to configure the IP Adress of CISCO AIRONET 1600i AP to access It through the Web browser and configure It?
we tried to assign a static IP using CLI so we downloaded Tera Term and tried to connect It using the DB Cable. The following message shows up:
*Mar 1 01:41:43.674: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
we tried to execute 'Enable' command and It works then we tried to execute 'config t' command but failed (the other commands do not work too):
APf07f.06f0.93b5#config t
^ % Invalid input detected at '^' marker.
I connected the Aironet AP to a Router which has 192.168.1.1 as a default IP Adress and thats what shows up on the terminal:
Translating "CISCO-CAPWAP-CONTROLLER.Home"...domain server (192.168.1.1)
*Mar 1 00:34:05.251: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:34:05.255: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.Home
Not in Bound state.
*Mar 1 00:34:50.754: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:34:53.766: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:34:53.830: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.5, mask 255.255.255.0, hostname APf07f.06f0.93b5Hi
By default these AP comes with lightweight image & require a WLC to manage it.(unless you specifically order this AP with autonomous image)
If you want to convert it autonomous (to use without a WLC) then you have to load an autonomous image to it. You should have an image like this (ap1g2-k9w7-tar.153-3.JAB.tar) to begin with (you may require a valid maintenance contract to download this from cisco web site)
Then you can follow one of the methods to convert it to a autonomous AP
1. http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
2. http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/
HTH
Rasika -
Hello,
i have 2 cisco aironet 1300 series configured as root bridge and non root bridge, i managed to configure them and they are associating only when they adjacent , when i separate them them communication fail , could you please help me to solve this . thxThose are very old bridges. So if they are still functioning okay, do they require external antennas or not and do you have external antennas if they do?
Antenna Interface
• AIR-BR1310G-x-K9 or AIR-LAP1310G-x-K9: Air interface (integrated directional antenna)
• AIR-BR1310G-x-K9-R or AIR-LAP1310G-x-K9R: Two RP-TNC type connectors for external antennas
-Scott -
Cisco Aironet 1300 - Coverage area
Hi,
could you please tell me what is the max coverage area that supports on Cisco Aironet 1300 with integrated antenna (13 dbi).Check out the following URLs
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
and
http://www.cisco.com/en/US/products/ps5861/prod_brochure09186a0080230777.html -
I got a Cisco Aironet card to replace the Broadcom that uses ndiswrapper. Here is what happens
modprobe airo
modprobe airo_ca
then run iwconfig
eth1 (which is my wireless card) no wireless extensions
A few places suggested that it is the driver. Anyone have any other suggestions? Does anyone use a Cisco Aironet card? How did you get it installed?i have aironet 350
modprobe
yenta_socket , pcmcia_core , airo , & airo_cs
in rc.conf
lo="lo 127.0.0.1"
#eth0="dhcp"
eth1="dhcp"
INTERFACES=(lo !eth0 eth1)
DAEMONS=(syslog-ng !hotplug pcmcia network netfs crond )
but since the upgrades that came out the other day
it doesnt work at boot up i have to unplug then plugin card
run as root
ifconfig -a
dhcpcd eth1 or i could use
dhcpcd wifi0
from what ive read so far its a udev prob havent been able to figure it out yet
so im plugging away at that -
Can a CISCO Aironet 700w be set up as Antonius Access Point ? I was able to set up 700i OK no problem
Need to Set it up for WIFI site Survey Active to test coverageThe 700W series access point contains two simultaneous dual-band radios, the 2.4 GHz and 5 GHz 802.11n MIMO radios, in a controller-based mode.
Source: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/702W/quick/guide/ap702Wgetstart.html -
Cisco Aironet 1200
Firmware 12.3(8)JEB
Hello,
I want to control client associations when AP load is high.
Is there an MIB object that enables/disables client associations?
I have searched the supported MIBS, but i could not find anything.An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Here is the URL which indicate indicates the maximum power levels allowed with the Cisco integrated antenna for each regulatory domain and also contain configuration setting.
http://www.cisco.com/en/US/docs/wireless/access_point/1200/vxworks/installation/guide/higaxd_2.html
Maybe you are looking for
-
AP payment batch is running very slow
Dear All, We have an issue with AP payment batch, wherein the batch is unning very very slow. The DB is currently on 11gR2 with application on CU2. After having a close look into it we have seen an SQL ID dq3nnqyx0u7ht. Please help us if any patch is
-
Null Values to internal tables
I need to pass Null Value to couple of fields in Internal table and one of them is type i. Any way to do it?
-
How to get an N wireless USB adapter to transfer data faster that 54 Mbps
How to get an N wireless USB adapter to transfer data faster that 54 Mbps? I am running FIOS 10/2 and connected to a ActionTec M1424WR router. Any help will be appreciated.
-
I have tried this method several times & there is no option anywhere to select certain photos to be imported! Sure I can import ALL my photos but what I want is to only import a few! whoever keeps posting the same method is wrong!
-
Set Location of JPanel in another JPanel
Hello, i want to set the location of a JPanel in another JPanel. This is my code: * To change this template, choose Tools | Templates * and open the template in the editor. package nemo; * @author Administrator import java.awt.event.*; import javax.s