Cisco Aironet 2600 not responding after changing static IP using web GUI

Hey guys, I am hoping someone can point me in the right direction with this problem I am having. Over the weekend I changed the IP address of one of our remote Access points so that it would be in the correct VLAN for the building it is in. There are already 2 other AP's in that office and so I changed the IP/Default Gateway of our newly installed AP to match. As soon as I did this, I lost connection with the AP. I can no longer ping the AP or connect to its web interface. I am able to view the AP when I do a #Show cdp neighbors detail. I can see that it has the correct IP address. But when I do a #show arp, I do not see the AP. When I do a #Show mac address-table, I can see the AP and it's MAC address as well. Does anyone know what I may have done wrong/still need to do in order to get this AP back up and running? I am unable to...
This topic first appeared in the Spiceworks Community

if the printer is shown under print in Airport Utility then select the update button.

Similar Messages

Premiere cs4 Not Responding after a few mins use

Hello,
I have been using premiere cs4 to make stop motion videos for awhile on this computer and have started having problems with the software.
Everytime I try to use it after a few mins sometimes 5 sometime less it goes white and says not responding resulting in having to close the program. Im starting to get late on deadlines and this is becoming a problem. Ive resorted to doing one step saving then having to close the program and repeat the process.
My system...
i5 750 OCed to 3.5ghz
8gb 1600mhz ram
I know its not the best but untill now its done this work for me fine. I am using stills at a res of 1920x1080 at 150 dpi and there are thousands of stills but again This is a new problem and I have been doing this for awhile with no issues.
Any ideas would be greatly appreciated.

Hello,
Thanks for the quick reply.
I did attempt a small batch sized as you stated but it did not help. It doesnt seem to matter what I'm working on within the program I could have no content and just click different menus and within mins the system will stop responding. That being said the final video must be in 1080p.
Here are the the items requested in the FAQ given.
i5 750 OCed to 3.5ghz also tried stock clock settings.
8gbs 1600mhz ram
2 hhd set up as follows
500gb 7400rpm hdd, program Pagefile, Media cache
1tb 7400rpm hdd, media, project file, previews
4gb virtual page file
win 7 fully updated
premiere pro fully updated
No Audio used
Ive tried various file sizes and settings to match those files all with same result.
As I state above the actual conent size, type and quantity doesnt seem to matter 3-5 mins in and it just stops responding.
Things ive tried so far.
I did extensive mem tests on my ram with no issues
reverted my over clock to stock settings
reinstall the software several times.
Also of note my ram never goes over 50% usage so Im not using all my ram.
I hope this helps i tried to include everything mentioned on the listed FAQ

Safari Message: Server Not Responding after 3 minutes of using.

Hi All,
I have seen the many topics on this forum asking about Safari crashing. I am having an issue - not sure if it is the same one.
After about 4-5 clicks in, Safari just hangs. If I let it time out - I get a message telling me that the Server isn't responding. This is for main websites like cnn.com, marketwatch, people, etc. Also, it seems as if when it stops, it closes off my email in Entourage but iChat is still working. I have tried firefox and sometimes it happens, sometimes not.
But if I click on the wireless icon it seems to kick things back into gear. Do you think this is a Safari problem or Airport Issue?
Thanks!!

Hi there,
I have the machine back and still having the issue. Though not as often. I am getting frustrated because I can't seem to figure it out. The machine works perfectly - they on occasion, the internet goes out. I will check and re-check my router - but we have 2 other wireless PCs (not apple) on it and no issues. The only thing I can think of is when my MobileMe Syncs - I get dropped... even off of iChat. Have you ever heard of that? I appreciate the help!

Trackpad does not respond after a second when using Keyboard

This problem is still persistent even after setting the SmartSense sliders to "off" and the Option in Mouse and Touchpad Settings to "No Delay". After researching online, some users in other blogs recommended changing the values in the registry, specifically the string called "PalmKms" to 0 value. Is this recommended, or is there another solution? I would rather not change values in my registry, as I do not know how it will affect my computer.

Mylenium
Thank you for the suggestions.
I checked the WIndows log files. It reported the following error:
The program Acrobat.exe version 10.1.1.33 stopped interacting with Windows and was closed. To see if more information about the problem is available, check the problem history in the Action Center control panel.
Process ID: 4770
Start Time: 01d0079a09bba381
Termination Time: 13
Application Path: C:\Program Files (x86)\Adobe\Acrobat 10.0\Acrobat\Acrobat.exe
Report Id: 4f145db6-7391-11e4-8fc1-005056c00001
I ran for the memory diagnostics as it showed the error with video card error. My NVDIA graphics card is not working properly. Do you think that could be a problem?I am running on Windows 7 64 bit computer. It also complains about the incompatibility with 64 bits.
Thank you.

When I try to open firefox it says that it is not responding, after I disabled the adobe flash plug-in it worked, how do I get it to work with flash

Since I updated my adobe flash player firefox keeps saying that it is not responding after I open it and it loads my home page, I disabled add-ons and went throught the process of figuring out which one it was and it was adobe flash, but without flash I cant access a lot of different sites, how can I fix this. I have tried uninstalling and reinstalling both firefox and adobe flash, but neither works!

See "Hang at exit":
* http://kb.mozillazine.org/Firefox_hangs
* [[Firefox hangs]]

App Store not responding after upgrade to OS X Mavericks and installing free Keynote, Pages and Numbers app

My App Store is not responding after upgrading to Mavericks and installing free Keynote, Pages and Numbers Apps.
Also I tried to reboot and restart and nothing happens still unresponsive.
Tried to click as many times as I can the App Store and it won't open.
Please Help.

Dongski
I had the same problem and solved it myself.
Please see discussion https://discussions.apple.com/message/23556072#23556072
Hope it helps

My Adobe acrobat X Pro does not respond after a minute I open up a pdf file

I recently have installed Adobe Master Suite CS6 Collection. My Adobe acrobat X Pro does not respond after a minute I open up a pdf file. This happens every time when open a new pdf file. My operating system is Windows 7 pro ( Lenovo-64 bits). Any suggestions would be appreciated !!

Mylenium
Thank you for the suggestions.
I checked the WIndows log files. It reported the following error:
The program Acrobat.exe version 10.1.1.33 stopped interacting with Windows and was closed. To see if more information about the problem is available, check the problem history in the Action Center control panel.
Process ID: 4770
Start Time: 01d0079a09bba381
Termination Time: 13
Application Path: C:\Program Files (x86)\Adobe\Acrobat 10.0\Acrobat\Acrobat.exe
Report Id: 4f145db6-7391-11e4-8fc1-005056c00001
I ran for the memory diagnostics as it showed the error with video card error. My NVDIA graphics card is not working properly. Do you think that could be a problem?I am running on Windows 7 64 bit computer. It also complains about the incompatibility with 64 bits.
Thank you.

Premiere Pro CS6 not responding after adding anything to timeline

I had been using Premiere CS6 successfully for a while, but starting a few months ago, it started not responding after I did anything. I can add a title and a transition succesfully to the timeline and it plays fine, but as soon as I add a picture or video clip, it immediately stops responding. It's frustrating because the program used to work fine before.
The only thing I can think of that might have affected it was when I upgraded to Mavericks, but I haven't read anything about any serious problems with Premiere running on Mavericks. I have a late 2008 MacBook Pro.
Thanks in advance for the help.

Go to http://forums.adobe.com/community/premiere and, in the area just under Ask a Question, type in
mavericks
You may now read previous discussions on this subject... be sure to click the See More Results at the bottom of the initial, short list if the initial list does not answer your question
I am Windows so did not bookmark the messages, but I have seen SOME message threads with SOME solutions for SOME mavericks problems

HT4623 why my iphone are not responding after i update the latest ios? and the screen displaying itunes icon

why my iphone are not responding after i update the latest ios? and the screen displaying itunes icon

You are in Recovery Mode. Follow the instructions below to recover your iPad.
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button.
5. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: You need to be patient and repeat the above many times to recover your iPad. Data will be lost.

Garageband not responding after upgrade to MacOS 10.5.8

Garageband is not responding after an upgrade from Mac 10.4 to 10.5.8. how can I fix this

Hello,
Do you have some Sound amplifying App installed?
If so remove it & reboot.

Cisco aironet 2600 series AP configuration with windows 2008 R2 Radius server.

I want to know the configuration of Cisco aironet 2600 series AP with windows 2008 R2 Radius server.
I have
1. AD & DHCP Server
2. Cisco Aironet 2600 Access Point.
I want to connect wifi devices through this AP. Authentication should be through Radius server and AD.

Hi ,
Below link should support your requirement
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116584-configure-wirelesslan-00.html
Minimal command : -
AP(config)# aaa new-model
AP(config)# radius-server host 172.20.0.1 auth-port 1645 acct-port 1645 key XXXXXX
AP(config)# radius-server deadtime 10
HTH
Sandy

Is anyone having trouble with the "home" button not responding after upgrading to 5.1.1 OS?

Is anyone having problems with the "home" button not responding after upgrading to 5.1.1?

You will not belive how I accidently solved this - !!!
Yes I had the problem immediately after the 5.1.1 'cloud' upgrade, the problems started (on my iphone 4) ... I followed the 'get power down button, then hold HOME for 30 secs' solution, but no result, nothing seemed to work and I was starting to get a bit agressive with the keep it pushed, multiple double click frustrations, icopybot multigesture solutions etc. and paid money ... but this comedy solution now works ...
I discovered it because I ordered a waterproof case for my iphone for my motorcycle ... I've just fitted it to my iphone and all the problems have gone ??? what! ... so wondering why I looked at what the home button on the casing was doing - it was pressing ACROSS the home button i.e. it converted my finger point into a wider 'PRESS
so taking the new case off, instead of using the point of my thumb to press HOME, I used the flat of my thumb to emulate it ....and initially nothing, so I wondered if it wa making better 'cross button' contacts, so I licked my thumb, wiped it and then tried again! - it worked!
I can't explain it but it seems to work - try it! if the double click on HOME doesn't work lick your thumb dry it and try again! I've just done it again
what a mad techno world we live in! :-)
Dave

BC4j/JSP Application not responding after some time - when deployed on 9ias

Hi,
We are using BC4j/jsp application on 9ias. The application is not responding
after some time. We have installed 9ias on PIII(384MB RAM). We tried to accesses
with 10 users, and server is not responding to BC4J/JSP application.
However the server could able to publish the JSP pages with standerad JDBC code even after that.
many many thanks in advance
null

When the application deployed by BC4J/JSP not responding, does the sample JSP application still works? i.e. does any other application respond? Does 1 user respond? Is the database source (JDBC), running Oracle 8.1.7? What is the platform running the database (e.g. local NT database)?

BC4j/JSP Application not responding after some time - when deployed on 9ias BC4j/JSP

Hi,
We are using BC4j/jsp application on 9ias. The application is not responding
after some time. We have installed 9ias on PIII(384MB RAM). We tried to accesses
with 10 users, and server is not responding to BC4J/JSP application.
However the server could able to publish the JSP pages with standerad JDBC code even after that.
Please....help us.........
many many thanks in advance

<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Is there any mechanism that cleans up these connections (back down to the initial or some other minimum I would guess) or do they hang around until either the app server or database shuts down?<HR></BLOCKQUOTE>
There is currently no mechanism for reducing the connection pool size after a period of high activity. Recently this has been frequently requested and as such will be implemented in the next production release.
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>We have verified this in manual testing. However, when the load tool script exits it doesn't seem to release resources. We know this because we keep seeing our database connections go up and up as more tests are run. Further, we also seem to see more than one connection per "virtual user". For example, when I connect 5 users to the app in manual testing, I get 5 connections. But, when we run a test using the tool, we get 395 database sessions for 200 users. We are having a bit of difficulty understanding why the behavior is different.<HR></BLOCKQUOTE>
Assuming that the you are performing your manual testing against the same instance of the application on which you are performing your load testing, I would assume that the connections are being released to the pool at the end of the request. One possible reason for the approximate 2:1 ratio between connections and virtual users may be BC4J's use of internal connections. What version of BC4J are you using?
BC4J requires an internal connection to support state management and spill to disk. The internal connections are pooled with the transaction connection and only held for the duration of the persistence operation. However, if the web server is very busy then a large number of synchronous persistence requests may be received which would explain the eventual 2:1 ratio in the pool's high water mark.
If the user start times and think times are staggered in order to reduce the incidence of synchronous persistence requests does the ratio of connections to web sessions stabilize at some lower number (i.e. 1.5:1)

HT1430 my iphone 5 is not responding after the installation of ios7 ?

MY IPHONE 5 IS NOT RESPONDING AFTER INSTALLING IOS7 TODAY. NOT EVEN
ABLE TO POWER OFF.
Is there anybody to help me?

Perhaps if YOU STOP SHOUTING someone will help you.
What have you done to troubleshoot thus far? Have you taken the steps recommended in the User Guide (restart, reset, restore from backup, restore as new)

Cisco Aironet 2600 not responding after changing static IP using web GUI

Similar Messages

Maybe you are looking for