Cisco aironet RM1252 11g webinterface
i am having one cisco aironet 1252 11g accespoint.when connecting to dhcp is getting an ip,but i am not able to open it through webinterface .also i tried console (using putty),but unable to go to configuration mode.
please help what will be the problem..
Hii
I am assuming that is Autonomous AP. Try enabling HTTP on the AP by using command
ip http server in global config
Give it a try ..
vinay
Similar Messages
-
Cisco Aironet 1200 wireless network very slow
I have a simple wireless network set up, 2 - Cisco Aironet 1200 AIR-AP1220B-A-K9 wireless access points with 2 dBi Diversity Omni directional Ceiling Mount Antennas. They are the only devices connected to a Multitech Routfinder router, the WAN side the router is connected to a dedicated DSL connection. They are powered by AIR-PWRINJ3 power injectors. The WAP get the IP address from the DHCP in the router.
When connecting to the wireless network it runs very very slow, the signal strength is excellent and the connection speed is 54 mbps. But when opening a web browser it takes for ever to load a simple page like msn.com. If I connect the notebook directly to the router it runs very fast. We have tested with several notebooks and have the same problem. When I view the available wireless networks in range the only two that show up are the two Cisco 1200 WAP.
I have done the following with no improvement:
Change the channels from auto to 6 on one and 11 on the other.
Reset to factory defaults.
Update the firmware to c1200-k9w7-tar.123-7.JA2.tar
Replace the 802.11b radios with 802.11g radios AIR-MP21G-A-K9.
Disable the Aironet extensions.
Following is the configuration from one of the access points (before the firmware update):
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname MMA1
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa authorization ipmobile default group rad_pmip
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
username xxxx privilege 15 password xxxx
username xxx privilege 15 password xxxx
ip subnet-zero
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid MMA1
authentication open
guest-mode
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0
rts threshold 2312
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.10.100 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
ip http server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivory/1100
ip http authentication aaa
bridge 1 route ip
line con 0
line vty 5 15
End
Any suggestions would be greatly appreciated.
Best regards,
RandyThanks for the info.
The documentation say not to switch from auto to full duplex or half duplex when using inline power, well I think it says the AP may reboot. I may have tried half duplex before I upgraded the firmware.
While upgrading I disconnected the AP, used a patch cord to connect it to the router and pluged the power directly into it to make sure the wiring to the AP was not the problem and it did the same thing.
However, when trying to upgrade the firmware it took ~ 45 minuets to upload the image and filed a couple of times retrying. I connected the AP to the notebook directly with a crossover cable and it uploaded in about 45 seconds.
That got me to thinking that there may be a problem with the router so I have replaced it with a Linksys.
In the mean time the DSL went down yesterday so I have not been able to test the new setup.
The cables are T568B
W/O
O/W
W/G
B/W
W/B
G/W
W/B
B/W
Best regards,
Randy -
How to change default admin password on Cisco Aironet 1040
How do I change the default username and password on the Cisco Aironet 1040. There is a default set and I want to change that to secure the device. I've checked the manual and can't seem to find the directions. Any ideas?
Hi Brian,
If this AP is already registered with a WLC then you can change it via WLC.
In WLC GUI, go to Wireless -> Select the AP -> Credential -> Override Global Credential-> Update username/pw/enable pw
In WLC CLI, you can configure it like this. If it is for all APs, then select all, otherwise AP name.
(WLC3) >config ap mgmtuser add username admin password Cisco123 secret Cisco123 ?
all Applies the configuration to every AP that does not have a specific user name.
Enter the name of the Cisco AP.
(WLC3) >config ap mgmtuser add username password secret
(WLC3) >save config
Are you sure you want to save? (y/n) y
If it is Autonomous AP you can configure using the "username xxxx password xxx" IOS command
HTH
Rasika
*** Pls rate all useful responses **** -
How many users are supported on a Cisco Aironet 1141N? 30?
I have a client that wants to upgrade his Aironet 1131 APs with 1141N. How many users are supported on a Cisco Aironet 1141N?
Yes, you could have 30 clients on the AP.
Client density all depends on what the client is doing, really.
So if you have clients that are just web surfing and pulling email 30+ isn't a problem. If they are all streaming video, then you want to plan for less clients per AP, and more APs.
Steve -
How to load a boot image to cisco aironet 1140 series after missing boot image
Hi all,
I need a solution for this. When i switch my cisco aironet 1140 , it s blinking with red light .and gives a message "no boot image to load".
When i tried next time, by pressing escape it shows this message that i have mentioned below.
ap:
ap:
using eeprom values
WRDTR,CLKTR: 0x83000800 0x40000000
RQDC ,RFDC : 0x80000035 0x00000208
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0x40000000
RQDC, RFDC : 0x80000035, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialized
PCIEx: initialization done
flashfs[0]: 1 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 1536
flashfs[0]: Bytes available: 32383488
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 28:94:0f:d6:c8:62
Ethernet speed is 100 Mb - FULL duplex
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Tue 18-Oct-11 14:51 by prod_rel_team
ap:
So , now my question is how to load the boot image ? From where will we get this ? OR
I m also having another Cisco aironet 1140 , Can i get bootimage from that . Kindly let me know the solution from genius ?Take a look at this link as it should have the info you need
https://supportforums.cisco.com/docs/DOC-14636
Sent from Cisco Technical Support iPhone App -
Hello, I have 2 Cisco Aironet 1300 Bridges which provide data and voice communication between 2 buildings. Up until recently QoS has not been needed, but lately there appears to be congestion due to reports of poor voice quality. Building A houses a V3000 NBX Telephone system, Building B houses approximately 30 remote IP phones. Building A and Building B are approximately 100 yards apart. No VLAN's. Due to myself being an extreme noob to Cisco bridges, I was hoping some of you may have had experience in setting this up and hopefully provide some tips. I need to prioritize traffic on UDP ports 2093-2096 and TCP port 1040. Thank you in advance for any suggestions. My current running config is below:
Using 1283 out of 32768 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LHS-WeightRoom-WCV
ip subnet-zero
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 ssid wcv
authentication open
guest-mode
dot11 ssid wcvcisco
authentication open
infrastructure-ssid optional
username root privilege 15 password 7 0247335A05320A2244
username Cisco privilege 15 password 7 074E164D403D1C061F
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid wcv
ssid wcvcisco
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
54.0
station-role root bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 10.141.8.6 255.255.254.0
no ip route-cache
ip default-gateway 10.141.8.5
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
endHere is the URL for the configuration of Cisco Aironet 1300 QoS. Follow the guide it may help you
http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html -
Hello,good day problem with Cisco aironet 1040 series acces point
Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
melhelo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040 sir?
waiting for a step by step instruction,
thank you in advance
mel -
Hello;
how to configure the IP Adress of CISCO AIRONET 1600i AP to access It through the Web browser and configure It?
we tried to assign a static IP using CLI so we downloaded Tera Term and tried to connect It using the DB Cable. The following message shows up:
*Mar 1 01:41:43.674: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
we tried to execute 'Enable' command and It works then we tried to execute 'config t' command but failed (the other commands do not work too):
APf07f.06f0.93b5#config t
^ % Invalid input detected at '^' marker.
I connected the Aironet AP to a Router which has 192.168.1.1 as a default IP Adress and thats what shows up on the terminal:
Translating "CISCO-CAPWAP-CONTROLLER.Home"...domain server (192.168.1.1)
*Mar 1 00:34:05.251: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:34:05.255: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.Home
Not in Bound state.
*Mar 1 00:34:50.754: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:34:53.766: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:34:53.830: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.5, mask 255.255.255.0, hostname APf07f.06f0.93b5Hi
By default these AP comes with lightweight image & require a WLC to manage it.(unless you specifically order this AP with autonomous image)
If you want to convert it autonomous (to use without a WLC) then you have to load an autonomous image to it. You should have an image like this (ap1g2-k9w7-tar.153-3.JAB.tar) to begin with (you may require a valid maintenance contract to download this from cisco web site)
Then you can follow one of the methods to convert it to a autonomous AP
1. http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
2. http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/
HTH
Rasika -
Hello,
i have 2 cisco aironet 1300 series configured as root bridge and non root bridge, i managed to configure them and they are associating only when they adjacent , when i separate them them communication fail , could you please help me to solve this . thxThose are very old bridges. So if they are still functioning okay, do they require external antennas or not and do you have external antennas if they do?
Antenna Interface
• AIR-BR1310G-x-K9 or AIR-LAP1310G-x-K9: Air interface (integrated directional antenna)
• AIR-BR1310G-x-K9-R or AIR-LAP1310G-x-K9R: Two RP-TNC type connectors for external antennas
-Scott -
Cisco Aironet 1300 - Coverage area
Hi,
could you please tell me what is the max coverage area that supports on Cisco Aironet 1300 with integrated antenna (13 dbi).Check out the following URLs
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
and
http://www.cisco.com/en/US/products/ps5861/prod_brochure09186a0080230777.html -
I got a Cisco Aironet card to replace the Broadcom that uses ndiswrapper. Here is what happens
modprobe airo
modprobe airo_ca
then run iwconfig
eth1 (which is my wireless card) no wireless extensions
A few places suggested that it is the driver. Anyone have any other suggestions? Does anyone use a Cisco Aironet card? How did you get it installed?i have aironet 350
modprobe
yenta_socket , pcmcia_core , airo , & airo_cs
in rc.conf
lo="lo 127.0.0.1"
#eth0="dhcp"
eth1="dhcp"
INTERFACES=(lo !eth0 eth1)
DAEMONS=(syslog-ng !hotplug pcmcia network netfs crond )
but since the upgrades that came out the other day
it doesnt work at boot up i have to unplug then plugin card
run as root
ifconfig -a
dhcpcd eth1 or i could use
dhcpcd wifi0
from what ive read so far its a udev prob havent been able to figure it out yet
so im plugging away at that -
On the Cisco Aironet 1500 Series Lightweight Outdoor Mesh Access Point spec sheet from the Cisco.com website, it states that the input power for the DC inline POE is 28.5 W at 48 VDC, nominal. What is the maximum power at 48 VDC? On AC, the nominal power is 57.8W at 120 VAC. What is the maximum power at 120 VAC?
Also, I see that the Cisco 1510 only uses AC as a source. Does Cisco have a device for the Cisco Aironet 1510 that uses DC as a source? For example, instead of using the POE Injector that Cisco has, which uses an input of 120VAC (1.5A) and outputs 48VDC (1.2A), does Cisco have a POE Injector that uses an input of 12VDC and outputs 48VDC (1.2A).I think the maximum draw (with both radios and heater on) is 57.8 Watts, but with the heater not active it's much lower around 36.84 Watts.
-
Can a CISCO Aironet 700w be set up as Antonius Access Point ? I was able to set up 700i OK no problem
Need to Set it up for WIFI site Survey Active to test coverageThe 700W series access point contains two simultaneous dual-band radios, the 2.4 GHz and 5 GHz 802.11n MIMO radios, in a controller-based mode.
Source: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/702W/quick/guide/ap702Wgetstart.html -
Cisco Aironet 1200
Firmware 12.3(8)JEB
Hello,
I want to control client associations when AP load is high.
Is there an MIB object that enables/disables client associations?
I have searched the supported MIBS, but i could not find anything.An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Here is the URL which indicate indicates the maximum power levels allowed with the Cisco integrated antenna for each regulatory domain and also contain configuration setting.
http://www.cisco.com/en/US/docs/wireless/access_point/1200/vxworks/installation/guide/higaxd_2.html -
Cisco Aironet 350 series/panel indicator
Cisco Aironet 350
I have the next indicators signals:
Ethernet activity= Steady RED
Association Status=Steady GREEN
Radio Activity=Steady AMBER
I can't use the acces point's serial for management systemHere is a link to the led indicators although your colors aren't shown in the list.
http://www.cisco.com/public/scc/compass/ap/information_files/led_table_wbg.html
Based on the age of the unit, no access to the console, all LEDs are on. I would agree with Scott. It's likely bad ..
Sent from Cisco Technical Support iPad App
Maybe you are looking for
-
Can I change a field/column width in a script ?
Can I change a field/column width in a script to be run in SQL Plus? For example, I have a table where field COL1 is a varchar2(200). The table already has data in it. I would like to increase the width of field COL1 to be varchar2(300). Can I do thi
-
How do I stop page reload when I go to previous page?
I want to press back and get the same image, haven't had this problem in years. Now all of a sudden everytime I click back, the page reloads
-
Hi all, I'm trying to create a user exit for the PM transaction IW32 (change order) that occurs when the user clicks save. I have found a user exit that is in the correct place (EXIT_SAPLCOIH_009). How do I access the data that the user has just ente
-
Open Livecycle ES2 form from c#
Hi All, I am working on MS Visual studio 2008 C#. I have the Live cycle Designr ES@ trial version installed on my machine. I have designed a PDF form and it opens properly in the preview mode. this form has drop downs and editable fields as well as d
-
Error when downloading TV Show Lost
Everytime i try to download the first episode of Season 2 of Lost.. "Man of Science, Man of Faith" i get an error OxFFFE7958.. Ive tried it on different computers and still get the error.