Cisco AP 1131AG Web Interface Problem

Hello,
I purchased two Cisco access points (model AIR-AP1131AG-A-K9) from a seller on eBay. The Access Points power up fine and are able to get an IP address (I can see the AP's MAC address on my router), but it won't let me connect to the web interface to manage it. I have tried using different browsers, but they all say something along the lines of "The page could not be found" when I enter the IP address into my browser. No login screen, no nothing: just a time-out error.
When the Access Points are powered on, the Ethernet and Radio lights start out green, but then the Ethernet light stays green and the radio light flashes amber and the two alternate being lit. The status light on the outside of the Access Point goes from green to orange to red and back again, looping infinitely.
Any ideas what could be wrong? Thanks for any and all help in advance! (Please let me know if you need more information; I don't ahve the AP's with me, but I will be home in a few hours and can respond then.)

do a show cdp neighbor detail on the port the AP is connected to.  Take a look at the software that is running, IOS will show k9w7, and lightweight will show k9w8.
if it''s k9w8, you'll need to convert them back to IOS
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Similar Messages

  • Cisco SPA514g Secure web interface only.

    I have a Cisco SPA514g, I want to secure the web interface with a password. When I change the password and it reboots the phone comes up fine. On certain functions in now asks for the user password for example on redial. Is there a way to disable the security on these functions other than removing the password on the profile "user"?

    Use the following document http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo1100/accsspts/i12213ja/i12213sc/s13web.htm to get access to the Web interface

  • Cisco 881W - ap gui interface problem

    We have a new Cisco 881W wireless router;
    used the CP Express gui interface to perform initial setup;
    router assigned 10.10.10.3 as wireless ap gui interface;
    when entering ap gui the entire screen is blank expect for an "enter" button near bottom;
    clicking on this button does nothing; "error on page" is indicated on IE8 status;
    assigned SSID is not broadcasting

    Hi !!
    im the same problem , but i fix it
    first you must change the IOS version to ap801-k9w7-tar.124-10b.JDA3 ( you can dowload for the cisco web )
    after download the image file you putt this command in the ap exec mode:
    ap#archive download-sw /overwrite /force-reload tftp://x.x.x.x/ap801-k9w7-tar.124-10b.JDA3.tar
    after the files are copied to flash memmory , the routyer boots with the new image ang bug fixed
    its is my configuration working: 
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    Current configuration : 3267 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname ap
    enable secret 5 $1$T0Qk$/wKGmrwqo0WcBbvTapaNb.
    no aaa new-model
    dot11 ssid CASIO
       vlan 1
       authentication open
       authentication key-management wpa
       guest-mode
       wpa-psk ascii 7 121A04041B04010132222727
    crypto pki trustpoint TP-self-signed-4051168682
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-4051168682
    revocation-check none
    rsakeypair TP-self-signed-4051168682
    crypto pki certificate chain TP-self-signed-4051168682
    certificate self-signed 01
      3082023A 308201A3 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
      31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
      69666963 6174652D 34303531 31363836 3832301E 170D3131 30383139 31303037
      33385A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
      4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D34 30353131
      36383638 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
      8100B090 26BE5E77 FCB338C0 F54949DB 43EF95C1 61A9C3FA 38AC8BDC 18931195
      B1B1A503 65A71B68 8940639A FB6A6D9B 0F327B09 F5C48ECD 89C1B279 9DC6DC98
      11E5D014 914200BB 7F29CFD1 1CC5FDF0 F3AFE547 4954E2CA 37FC1CEC 60641871
      D9949391 35C958B3 FBA6FBF7 116612FD DFAB9467 478A6E07 0F7B2616 F1204158
      EC510203 010001A3 62306030 0F060355 1D130101 FF040530 030101FF 300D0603
      551D1104 06300482 02617030 1F060355 1D230418 30168014 1120DB6C BE01CDEE
      64A2DB14 FA240B27 D3573B9B 301D0603 551D0E04 16041411 20DB6CBE 01CDEE64
      A2DB14FA 240B27D3 573B9B30 0D06092A 864886F7 0D010104 05000381 81003B69
      8FC11090 E61D3BC1 D04FBDC5 622E8BC6 EB63B9FA C795BB15 BB05F417 CFC51F09
      A8A1971E 7E523203 5A40654D B71623CB A48B193A 101FD1AD 868128E9 91940B71
      5CFDDDD4 856B8170 7700C656 A75443DF DBB60F06 67E37A70 69175B84 24AB0380
      221AAA1D 3EB80465 FD1C1F49 B75B0F1D BC4A82B2 EB2176F2 27F54894 5E94
      quit
    username Cisco password 7 106D000A0618
    username ivan privilege 15 secret 5 $1$eEHQ$Dc.dDfXJz2fBbPIGhH.zg1
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption vlan 1 mode ciphers tkip
    ssid CASIO
    speed  basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
    station-role root
    interface Dot11Radio0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    description  the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
    no ip address
    no ip route-cache
    interface GigabitEthernet0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.10.5 255.255.255.0
    no ip route-cache
    ip http server
    ip http authentication local
    ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    bridge 1 route ip
    line con 0
    no activation-character
    line vty 0 4
    login local
    end
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    now you cant acces to ap web gui 
    thanks !!!

  • Lost The Cisco Aironet 1310 Web Interface????

    I've been having connection issues with my (2) Aironet 1310, which are setup in a bridge p2p mode.  A few weeks ago we had a power outage due to a lighting storm.  Well, it knocked out my non-root bridge (not connecting to the root).  So I brought it back to check the configurations, but when I try to use the web console all I get is the following page:
    When I click the "Web Console" link it takes me to the following page:
    Is there a way to get the original web console page back?

    here is the command..
    archive download-sw / force-reload /overwrite tftp:///
    Example..
    archive download-sw / force-reload /overwrite tftp:///c1310-k9w7-tar.124-21a.JA1.TAR
    to get the .TAR, go to the folder where the image is saved and then Tools >> folder options >> view >> check >> show hidden files and folders.
    Now click on the image and then copy the image name and then paste the same on the CLI... then this come as IMAGE.TAR that is.. c1310-k9w7-tar.124-21a.JA1.TAR instead of c1310-k9w7-tar.124-21a.JA1
    it should be c1310-k9w7-tar.124-21a.JA1.TAR
    lemme know how this works out for you!! if you face any difficulties while upgrading please open up a TAC case.. we wil solve this in less than 5 minutes... and the network wil be back up!!
    Regards
    Surendra

  • Cisco SA 520W Web Interface not loading.!!

    Hi
    Im going to start with saying this appliance is really winding me up!! The unit has been working fine for a while and i now need to make some changes. The unit is passing traffic fine, URL filtering is working fine however when i load the web page to control it says "The server is down.
    Connection failed " I have rebooted the device numerous times with no luck. I have tried a different laptop, cleared out cookies and all ie cash. tried a different browser. To no avail. Am loosing faith in this device
    Any ideas

    Hi accidentexchange,
    Did you fail to log in when accessing the SA 520W thru both HTTP and HTTPS?
    https://LAN_IP_address_of_SA520W/
    http://LAN_IP_address_of_SA520W/
    Furthermore,  can you give us an overview of your network topology and user info.  If  possible, can you provide us the configuration and dbglogs from your SA  520W so that I can forward to the development team?
    To get the dbglog from SA520W, login through web UI and in the browser enter the following URL:
    https://LAN_IP_address_of_SA520W/scgi-bin/dbglog.cgi        
    These   logs will store password, so please remove any password sensitive   information. Also if you are not comfortable posting the dbglog on the   community, you can send it directly to me through private message.
    Cheers,
    Julio

  • Web Interface of Cisco Prime 2.1 not working

    Excuse me!
    I install the trial version cisco prime 2.1 (OVA) on ESXi server
    I can ping cisco prime but web interface of cisco prime not worinking
    prime/admin# ncs status
    Health Monitor Server is running.
    Ftp Server is running
    Database server is running
    Tftp Server is running
    Matlab Server is running
    NMS Server is running.
    Plug and Play Gateway is running.
    SAM Daemon is running ...
    DA Daemon is running ...
    Syslog Daemon is running ...

    Services running fine..
    check it with other Browser , Supported browser are below::
    –    Google Chrome 31 or later.
    –    Microsoft Internet Explorer 8.0 or 9.0 with Google Chrome Frame plugin (users logging in to the simplified Lobby Ambassador interface do not need the plugin).
    –    Mozilla Firefox ESR 24.
    –    Mozilla Firefox 24, 25 or 26.
    If above does not help , reboot the server once and check the issue again.
    Thanks-
    Afroz
    ***Ratings Encourages Contributors ****

  • Web Interface of Cisco Prime Infrastructure Not Working

    Hi All,
    I installed the trial version of Cisco Prime Infrastructure 1.2 on ESXi server.
    It installed propersly and and i am able to ping it and also ssh into it.
    But when I try to access it via web interface, it does not work.
    I am provided with a login screen but after putting my credentials the page goes blank.
    There also an error on the page "Error occured while fetching Meatdata for Slider Panel" and there is a advertisemnt to download Google chrome Framework.
    When i do "NCS status" in CLI i see that every service is running.
    Does anyone know how to solve this.
    All your help is highly appreciated.                   

    Google Chrome Frame isnt supported anymore, using Google Chrome doesnt work with all features and forget about Firefox. Up until this morning I had it working on IE11 but some update caused me to have this problem again. Cisco needs to get this fixed. I use several applications from Cisco and they still can't figure out a way to have them all work on a single browser.

  • Problems access to a web application (Web Interface or Web report)

    Hi,
    We found problems with the access to web application. Some users have problems with direct links to the web applications(Web Interface or Web reporting), when they click on the link an error message appears, the message displays the following text:
    "Cannot open file Bex?sap-language=ENbsplanguge=ENcmd=idoc_TE.."
    Clicking in details the message is "No Access to specified file"
    For this users the access to excel reporting is correct, the message appears when they click on the direct web links through the browser or directly in BW system, but if they type the URL they can access. Other users can use the direct web link without problems.
    I highly appreciate any help or idea about how to solve this issue.
    Thanks in advance.

    HI,
    please ask to your basis that check the language of every single user on su01 tx.
    This is the problem i think.
    Natalia.

  • Performance Problems with Web Layouts in web interface

    Hello Gurus,
    We have a a BPS web interface tool which has the following design:
    1> A web interface with several tabs
    2> Each tab has around 3-4 input layouts which are dependent on each other
    3> In all there are 120-140 layouts that the tool uses...
    My questions were in term of performance
    1> Is there a limit to how many web layouts you can use per page/tab/view or if SAP recommends specific number of web layouts per page/tab/view ?
    2> If there is a limitation...our intention was to convert all the display layouts into BW reports so as to increase the performance of the tool....
    3> Would like to know the restriction on the number of users who can log into the tool as a specific point of time ? We may have 50-60 minimum using this tool.
    I would appreciate your help in this regard.
    Thanks in advance

    Hello Rashmi,
    Have you got a chance to look at the performance guide and SAP notes on BPS performance. If not here are the details
    https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/documents/a1-8-4/performance guide - sap sem bw bps.pdf
    Enclosed are the few SAP notes related for improving performance.
    358921 - Oracle database parameterization for SEM
    459897 - SEM-CPM: Performance when reading transaction data
    566713 – Required information for the analysis of performance problems 
    560369 - Proposals BW aggregates for SEM-BPS
    180605 - Oracle database parameter settings for BW
    124361 - Oracle parameterization (R/3 >= 4.x, Oracle 8.x / 9.x)
    358529 - Overview of performance notes
    350011 - Technical performance: Using the business content
    340246 - Techn. performance: Overview of statistics   
    417091 - Optimize execution time of planning functions
    Some of them are Oracle specific, ignore them if you are not oracle database. Hope this helps.
    Thanks,
    Praveen
    PS.Dont forget to reward points

  • Oracle11g: Problem in web interface

    Hi,
    I have a problem with web interface.
    I obtain this result as status of dbconsole:
    >
    C:\Documents and Settings\Administrator>emctl status dbconsole
    Oracle Enterprise Manager 11g Database Control Release 11.1.0.6.0
    Copyright (c) 1996, 2007 Oracle Corporation. All rights reserved.
    https://WS2003ORA:5501/em/console/aboutApplication
    Oracle Enterprise Manager 11g is not running.
    I tried this:
    >
    C:\Documents and Settings\Administrator>emctl start dbconsole
    Oracle Enterprise Manager 11g Database Control Release 11.1.0.6.0
    Copyright (c) 1996, 2007 Oracle Corporation. All rights reserved.
    https://WS2003ORA:5501/em/console/aboutApplication
    Starting Oracle Enterprise Manager 11g Database Control ...Requested service already running.
    In the emdctl.trc file I find these lines:
    >
    2009-04-16 17:59:56 Thread-3604 WARN http: snmehl_connect: connect failed to (WS2003ORA:5501): Impossibile to establish a connection. Persistent deny of the destination host.
    (error = 10061)
    2009-04-16 18:00:34 Thread-2396 WARN http: snmehl_connect: connect failed to (WS2003ORA:5501): Impossibile stabilire la connessione. Rifiuto persistente del computer di destinazione.
    (error = 10061)
    2009-04-16 18:01:13 Thread-3864 WARN http: snmehl_connect: connect failed to (WS2003ORA:5501): Impossibile stabilire la connessione. Rifiuto persistente del computer di destinazione.
    (error = 10061)
    2009-04-16 18:01:48 Thread-2548 WARN http: snmehl_connect: connect failed to (WS2003ORA:5501): Impossibile stabilire la connessione. Rifiuto persistente del computer di destinazione.
    (error = 10061)
    2009-04-16 18:02:27 Thread-3356 WARN http: snmehl_connect: connect failed to (WS2003ORA:5501): Impossibile to establish a connection. Persistent deny of the destination host.
    (error = 10061)
    I try to reconfigure the db with dbca but when I click finish I receive a message tells me that it does not exsist a configuration of the db.
    How can I solve?
    Thanks, bye bye.

    Hi,
    I do not know how but now the web interface works but I have a problem in the web console I see, as server host, a wrong ip, how can I change this ip?
    I open the web console with this url: https://192.168.132.128:5501/em/console/
    but when I try to execute some modify to the db through the interface I receive a login request and the connection string is: 92.168.223.128:1521:ws2003 where the ip is wrong! So I cannot connect to the db.
    How can I change the ip?
    Thanks, bye bye.

  • Cisco RM-1252G-A-K9 can't access web interface

    I hope I am in the correct forum for this topic?
    For some reason I cannot access the web interface in order to configure this device. I have it connected to a router (DHCP). The router assigns an IP Address and I can ping it. If I attempt to go to that IP Address in any web browser. the page cannot be displayed. I've reset it several times. I have 2 of these and same problem. Am I missing something obvious? I sure hope so...

    Connecting to the Access Point Locally
    If you need to configure the access point locally (without connecting it to a wired LAN), you can connect a PC to its console port by using a DB-9 to RJ-45 serial cable.
    Follow these steps to open the CLI by connecting to the access point console port.
    Step 1 Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and to the COM port on the PC.
    Step 2 Set up a terminal emulator on your PC to communicate with the access point. Use the following settings for the terminal emulator connection: 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.
    Assigning an IP Address Using the CLI
    When you assign an IP address to the access point using the CLI, you must assign the address to the BVI. Beginning in a privileged EXEC mode, follow these steps to assign an IP address to the access point BVI using the console port:
    Command
    Purpose
    Step 1
    enable
    Enter privileged EXEC mode.
    Step 2
    configure terminal
    Enter global configuration mode.
    Step 3
    Interface bvi1
    Enters interface configuration mode for the BVI.
    Step 4
    ip address address mask
    Assigns an IP address and subnet mask address to the BVI.
    Step 5
    end
    Return to privileged EXEC mode.

  • Privileged Exec password works for telnet but not web interface on Cisco AP 1242

    I recently configured a Cisco AP 1242, software version 12.4, via the web interface using the default Cisco credentials. At that time I setup an administrator account with read/write access and changed the Cisco to a read only access. Now went I attempt to login to the web interface it won't accept the administrator password. It will except the administrator password in a telnet session however. So via the telnet session I setup another user with privileged exec level access and that wont work on the web interface either. The Login box keeps coming back requesting a password. Strangely enough, I can login to the web Interface using admin username, with the Cisco password; but I can't do anything, and I also can't view everything.
    I've tried the following:
    I've turned on SSH and created a certificate in the AP, but the login box continues to pop on the https://url.
    I've attempted to setup a user with a non-encrypted password, but have been unsuccessful.
    I've tried a different browser - login box continues to pop.
    I've made sure the web interface is activated in the AP
    I've tried a differnet computer
    I've tried disabling password-encryption service
    Reset the enable password
    I've successfully setup other 1240 APs but must have done something wrong on this one. Anyone know what I'm missing? Thanks.
    Solution: I was missing "ip http authentication local" in my config.

    Solution: I was missing "ip http authentication local" in my config.

  • Facing problem in transportation of web Interface

    Hi BPS Experts,
    I am facing problem in transporting the web interface.
    As part of one enhancement I have made some changes to one of the objects in web Interface in Integration system. Before doing transportation to consolidation, generated the new BSP application as well as saved the customized changes under one request for transport.
    Used the request number for Transporting to consolidation. The Layout in the consolidation is displaying error message as follows
    *Error with initialization or error on BSP*
    Component with name Group_Selection1 does not exist
    BSP application ZEBSP08_RF does not exist. Regenerate
    and when i check the web interface under BPS_WB transaction in consolidation. i able to see the change in objects which i made in integration.
    Please help in solving this problem in Layout.
    Thanks in Advance,
    Anil.

    Hi Ravi,
    Create the same function group and send it into test system with another TR.
    Once it get transported to test system, try to activate FM & FG.
    Reward points if it helps,
    Satish

  • Cisco Prime 2.0 web interface access

    We just installed Cisco Prime Infrastructure 2.0 Express. It seemed to have installed correctly? But Two oddities. First when the system is restarted it takes and inordinate amount of time before the web interface becomes available. Once the web service is responding, it will not except ANY login credentials.
    I can ssh to the instance and using cli, added two additional accounts. All accounts can access the install instance using ssh. None are able to login to the webinterface.
    Thoughts as to what I may have missed?
    Gabe

    Please login to the CLI as admin then execute the command to change the password for the root WebUI acccount
         > ncs password root password Private123
         Loading USER - root
         Validating new password..
         Resetting password ..
         Resetting password  COMPLETED.
         EXECUTION STATUS : Success
    Once you've changed this password please then try to use those credentials to login to
    the WebUI you indicated was presented in your response above.
    Let me know if this does it. If not, we'll need to go a little deeper:::

  • Cisco 4402 WLC IOS Upgradation using CLI and Web Interface

    Hi,
    I would like to know how to upgrade IOS of Cisco 4402 WireLess LAN Controller using CLI and Web interface ?
    Can any one help me regarding the same.
    Please answer as soon as possible.
    Thanks in advance.

    Here are the instructions for upgrading the controllers via GUI:
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn52.html#wp472449
    Instructions via cli:
    Cisco recommends that a direct CLI console port connection is used to update the controller software.
    1. Make sure a TFTP server is available for the Operating System (OS) software download. Also, keep these guidelines in mind when the TFTP server is set up:
    If a download is performed through the service port, the TFTP server must be on the same subnet as the service port because the service port is not routable.
    If a download is performed through the Distribution System (DS) network port, the TFTP server can be on the same or a different subnet because the DS port is routable.
    The TFTP server cannot run on the same computer as the Cisco Wireless Control System (WCS) because WCS and the TFTP server use the same communication port.
    2. Download the desired OS software update file from the Cisco website to the default directory on the TFTP server.
    3. Log into the WLC CLI.
    4. Issue the ping server-ip-address command to verify that the WLC can contact the TFTP server.
    5. Issue the transfer download start command and answer n when prompted to view the current download settings.
    This example shows the command output:
    transfer download start
    Mode........................................... TFTP
    Data Type...................................... Code
    TFTP Server IP.................................
    xxx.xxx.xxx.xxx
    6. TFTP Path...................................... TFTP Filename.................................. AS_2000_3_0_x_x.aes --OR-- AS_4100_3_0_x_x.aes --OR-- AS_4400_3_0_x_x.aes Are you sure you want to start? (y/n) n Transfer Canceled Issue these commands to change the download settings:
    * transfer download mode tftp
    * transfer download datatype code
    * transfer download serverip tftp-server-ip-address
    * transfer download filename filename
    * transfer download path absolute-tftp-server-path-to-file
    Note: All TFTP servers require the full pathname. For example, in Windows, the path is C:\TFTP-Root. (In UNIX forward slashes (/) are required.)
    7. Issue the transfer download start command to view the updated settings, and answer y when prompted to confirm the current download settings and start the OS code download.
    This example shows the download command output:
    transfer download start
    Mode........................................... TFTP
    Data Type...................................... Code
    TFTP Server IP.................................
    xxx.xxx.xxx.xxx
    TFTP Path......................................
    path>
    TFTP Filename..................................
    AS_2000_3_0_x_x.aes --OR--
    AS_4100_3_0_x_x.aes --OR--
    AS_4400_3_0_x_x.aes
    Are you sure you want to start? (y/n) y
    TFTP Code transfer starting.
    TFTP receive complete... extracting components.
    Writing new bootloader to flash.
    Making backup copy of RTOS.
    Writing new RTOS to flash.
    Making backup copy of Code.
    Writing new Code to flash.
    TFTP File transfer operation completed successfully. Please
    restart the switch (reset system) for update to complete.
    8. The WLC now has the code update in active volatile RAM, but the reset system command must be issued to save the code update to non-volatile RAM (NVRAM) and reboot the WLC.
    This is a sample output:
    The system has unsaved changes.
    Would you like to save them now? (y/n) y
    The controller completes the bootup proce

Maybe you are looking for