Cisco AP 1240AG series Fast Ethernet cannot up

Hi all :
My question here is how is the IP configuration for this Fast Ethernet F0.
This is because usually we only assign IP to the BVI interface. Is it after that, the Fast Ethernet F0 automatically also be assigned the same IP?
As such, when goto the Fast Ethernet F0 by CLI, by using no shut then this will Enable the Fast Ethernet Port?
Thanks!
Best regards,
tangsuan

Hi Scott :
The problem is due to the patch line not connect up somewhere. After connect the line up, now the Optical Ethernet line is up.
Thanks for your help on this.
regards,
tangsuan

Similar Messages

Satellite L670 series: fast-ethernet or gigabit ethernet ?

Hi all,
Any L670 series Satellite owners on here ?
Looking at various websites, the common consensus is that the L670 series is not equiped with gigabit ethernet, but with regular fast-ethernet.
Can someone confirm or deny that please ?
Does it or does it not have gigabit ethernet ?
Many thanks,
Kind regards,
Rene Fennet

Hello
Differnet notebooks have different hardware so what Satellite L670 you have exactly?
Some models have Gbit but other models not.

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

Cisco Aironet 1300 Series Power

Can the 1310ap receive it's power from a POE switch?

Hi Edward,
Sadly the 1310 cannot be powered by PoE ,but, the Power Injector can be up to 100 meters away from the unit.
Dual coaxial cable to run from the power injector to the 1300. See attached notes:
Cisco Aironet 1300 Series
Cisco Aironet 1300 Series Access Point/Bridge Power Injector
The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
Ethernet Ports
The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
Power
The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
AIR-PWRINJ-BLR2
F-Type Connectors
Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
Hope this helps!
Rob

Ask the Experts: Understanding Cisco ASR 9000 Series Aggregation Services Routers Platform Architecture and Packet Forwarding Troubleshooting

With Xander Thuijs
Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn how to Cisco ASR 9000 Series Aggregation Services Routers with Cisco expert Xander Thuijs. The Cisco ASR 9000 Series Aggregation Services Routers product family offers a significant added value compared to the prior generations of carrier Ethernet routing offerings. The Cisco ASR 9000 Series is an operationally simple, future-optimized platform using next-generation hardware and software. The ASR 9000 platform family is composed of the Cisco ASR 9010 Router, the Cisco ASR 9006 Router, the Cisco ASR 9922 Router, Cisco ASR 9001 Router and the Cisco ASR 9000v Router.
This is a continuation of the live Webcast.
Xander Thuijs is a principal engineer for the Cisco ASR 9000 Series and Cisco IOS-XR product family at Cisco. He is an expert and advisor in many technology areas, including IP routing, WAN, WAN switching, MPLS, multicast, BNG, ISDN, VoIP, Carrier Ethernet, System Architecture, network design and many others. He has more than 20 years of industry experience in carrier Ethernet, carrier routing, and network access technologies. Xander holds a dual CCIE certification (number 6775) in service provider and voice technologies. He has a master of science degree in electrical engineering from Hogeschool van University in Amsterdam.
Remember to use the rating system to let Xander know if you have received an adequate response.
Xander might not be able to answer each question because of the volume expected during this event. Remember that you can continue the conversation on the Service Providers community XR OS And Platforms shortly after the event. This event lasts through Friday, May 24, 2013. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.
Webcast related links:
Slides
Webcast Video Recording
FAQ

Is there a Cisco lab available for ASR 9000
we have "XR4U" stations coming available soon when XR 511 comes alive. The plan is for a downloadable play image like that. In the interim we have 2 demo systems available, and they can be booked via your account manager representative.
How will MOD160 perform with multiple 9000NVS?
very well. the mod 160 has 4 NPU's, 2 per bay. So if you have a 4x10 MPA to serve a satellite, you effectively have a single NPU per 20 1Gigs from the satellite. The pps performance will be stellar. However it might be price technically more ideal to connect satellite with a 36x10. Since the MOD-x has native MPA's with 1G also.
2. Is there a shortcut for a Bundle-EthernetX interface, such as port-channel interface (poX), in Cisco IOS® ?.
usability enhancement is there, we are trying to push this into a new reasonable release. follow CSCuh04526
3. What is the revolutions per minute (RPM) on these hard disk drives (HDDs) compared to the solid state drives (SDDs)? Will the spinning drives be slow?
depends on the type we had avaialble at time of production, you will see different sizes and disks on the RSP2. the rpm of the HD is not so much an issue as much as the buffered writing we used to do in XR. This is fixed up with XR43 where the disk writing performance is much better. the HD/SDD is used for logging storage only (and maybe your pictures) but other then that we're not that concerned with write perf of the HD.
regards
xander

PCI Fast Ethernet Controller v2.13 error

Came home the other day to my screen repeating the following over and over again:
For Realtek RTL8139(X)/8130/810X PCI Fast Ethernet Controller v2.13 (020326)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM
Intel UNDI, PXE-2.0 (build 082)
Copyright (c) 1997-2000 Intel Corporation
Tried to reload Windows XP and had no avail what so ever, this the error i recieve:
Set up did not find any hard disk drives installed in your computer.
Make sure any hard disk drives are powered on and properly connected
to your computer, and that any disk related hardware configuration is
correct. This may involve running a manufacturer-supplied diagnostic or
setup program.
Setup cannot continue. To quit Setup, press F3.
Is my motherboard toast? Any suggestions welcome. Hate to see my machine go, after 5 years of great service.

PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM
Intel UNDI, PXE-2.0 (build 082)
It means the hard drive was not found by the BIOS. (PXE indicates an attempt to boot from a network - lower on the list.)
So it's the hard disk that's toast.
-Jerry

Problem on Cisco AP 1240AG and External Antenna

Hi all :
I am setting and configure the Cisco AP 1240AG with 5GHz External Antenna extension. The whole product is called iWap. The problem now is that the wireless signal amplitude only can reach 3 bars instaed of ful 5 bars.
Please help below few questions I have for this setup and configuration :
1. What is the default or original frequency of antenna of Cisco AP1240AG? Can a 5GHz antenna work with the AP 1240AG whereby it is run with 802.11a and 802.11g?
2. If 5GHz antenna can work with 802.11a or 802.11g, what is the setting or configuration needed to be done at the Cisco 1240AG? Or, no setting or configuration needed because it will automatically work by default?
Many Thanks in advance and best regards,
tangsuan

1240 is the product "line," 1242 is the specific model. The come in both G and AG variants. The link below is a picture of an AG variant (with both an 2.4 Ghz "A" radio and a 5 Ghz "G" radio). The two antenna ports on the top in the blow image are for the 5 Ghz radio, and there should be some blue text indicating as much.
http://www.cisco.com/en/US/prod/wireless/ps5678/ps6521/prod_large_photo0900aecd8031d92d.jpg
If you don't have the two antenna ports on top, and just have two near the ethernet and console ports, then you have a "G" model, which only have a 2.4 Ghz radio. See my pic below. G model on the left, AG on the right.

Ask the Expert: Different Flavors and Design with vPC on Cisco Nexus 5000 Series Switches

Welcome to the Cisco® Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about Cisco® NX-OS.
The biggest limitation to a classic port channel communication is that the port channel operates only between two devices. To overcome this limitation, Cisco NX-OS has a technology called virtual port channel (vPC). A pair of switches acting as a vPC peer endpoint looks like a single logical entity to port channel attached devices. The two devices that act as the logical port channel endpoint are actually two separate devices. This setup has the benefits of hardware redundancy combined with the benefits offered by a port channel, for example, loop management.
vPC technology is the main factor for success of Cisco Nexus® data center switches such as the Cisco Nexus 5000 Series, Nexus 7000 Series, and Nexus 2000 Series Switches.
This event is focused on discussing all possible types of vPC along-with best practices, failure scenarios, Cisco Technical Assistance Center (TAC) recommendations and troubleshooting
Vishal Mehta is a customer support engineer for the Cisco Data Center Server Virtualization Technical Assistance Center (TAC) team based in San Jose, California. He has been working in TAC for the past 3 years with a primary focus on data center technologies, such as the Cisco Nexus 5000 Series Switches, Cisco Unified Computing System™ (Cisco UCS®), Cisco Nexus 1000V Switch, and virtualization. He presented at Cisco Live in Orlando 2013 and will present at Cisco Live Milan 2014 (BRKCOM-3003, BRKDCT-3444, and LABDCT-2333). He holds a master’s degree from Rutgers University in electrical and computer engineering and has CCIE® certification (number 37139) in routing and switching, and service provider.
Nimit Pathak is a customer support engineer for the Cisco Data Center Server Virtualization TAC team based in San Jose, California, with primary focus on data center technologies, such as Cisco UCS, the Cisco Nexus 1000v Switch, and virtualization. Nimit holds a master's degree in electrical engineering from Bridgeport University, has CCNA® and CCNP® Nimit is also working on a Cisco data center CCIE® certification While also pursuing an MBA degree from Santa Clara University.
Remember to use the rating system to let Vishal and Nimit know if you have received an adequate response.
Because of the volume expected during this event, Vishal and Nimit might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure Community, under the subcommunity LAN, Switching & Routing, shortly after the event. This event lasts through August 29, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Gustavo
Please see my responses to your questions:
Yes almost all routing protocols use Multicast to establish adjacencies. We are dealing with two different type of traffic –Control Plane and Data Plane.
Control Plane: To establish Routing adjacency, the first packet (hello) is punted to CPU. So in the case of triangle routed VPC topology as specified on the Operations Guide Link, multicast for routing adjacencies will work. The hellos packets will be exchanged across all 3 routers and adjacency will be formed over VPC links
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/operations/n5k_L3_w_vpc_5500platform.html#wp999181
Now for Data Plane we have two types of traffic – Unicast and Multicast.
The Unicast traffic will not have any forwarding issues, but because the Layer 3 ECMP and port channel run independent hash calculations there is a possibility that when the Layer 3 ECMP chooses N5k-1 as the Layer 3 next hop for a destination address while the port channel hashing chooses the physical link toward N5k-2. In this scenario,N5k-2 receives packets from R with the N5k-1 MAC as the destination MAC.
Sending traffic over the peer-link to the correct gateway is acceptable for data forwarding, but it is suboptimal because it makes traffic cross the peer link when the traffic could be routed directly.
For that topology, Multicast Traffic might have complete traffic loss due to the fact that when a PIM router is connected to Cisco Nexus 5500 Platform switches in a vPC topology, the PIM join messages are received only by one switch. The multicast data might be received by the other switch.
The Loop avoidance works little different across Nexus 5000 and Nexus 7000.
Similarity: For both products, loop avoidance is possible due to VSL bit
The VSL bit is set in the DBUS header internal to the Nexus.
It is not something that is set in the ethernet packet that can be identified. The VSL bit is set on the port asic for the port used for the vPC peer link, so if you have Nexus A and Nexus B configured for vPC and a packet leaves Nexus A towards Nexus B, Nexus B will set the VSL bit on the ingress port ASIC. This is not something that would traverse the peer link.
This mechanism is used for loop prevention within the chassis.
The idea being that if the port came in the peer link from the vPC peer, the system makes the assumption that the vPC peer would have forwarded this packet out the vPC-enabled port-channels towards the end device, so the egress vpc interface's port-asic will filter the packet on egress.
Differences: In Nexus 5000 when it has to do L3-to-L2 lookup for forwarding traffic, the VSL bit is cleared and so the traffic is not dropped as compared to Nexus 7000 and Nexus 3000.
It still does loop prevention but the L3-to-L2 lookup is different in Nexus 5000 and Nexus 7000.
For more details please see below presentation:
https://supportforums.cisco.com/sites/default/files/session_14-_nexus.pdf
DCI Scenario: If 2 pairs are of Nexus 5000 then separation of L3/L2 links is not needed.
But in most scenarios I have seen pair of Nexus 5000 with pair of Nexus 7000 over DCI or 2 pairs of Nexus 7000 over DCI. If Nexus 7000 are used then L3 and L2 links are required for sure as mentioned on above presentation link.
Let us know if you have further questions.
Thanks,
Vishal

Solaris 10 vs. SiS 961B Fast Ethernet

I have installed Solaris 10. My computer has Asus P4S533 motherboard with
- SiS 961B integrated Fast Ethernet with ICS external PHY
- C-Media CMI8738 audio controller.
Solaris is working fine, but I cannot find a driver for the two hardware elements above. Which ethernet interface should I choose for the SiS 961B chip? Or how could I find and install a driver?

The SiS NIC might work with the sfe driver, from:
http://homepage2.nifty.com/mrym3/taiyodo/eng/index.htm

Extra fast/ethernet port on 2610 router?

I am looking for a way to add an extra ethernet port on my 2610. What i have read is making me wonder if the only way to do this would be the NM-1E or NM-4E. Are there any other modules or WICs that would give me an fast/ethernet port?
Thanks,
Kyle

Hi,
NM-2FE2W & NM-1FE2W
is one which is supported by the new model 2691. Since 2610 is end of line cisco will not support it.
If possible you can try inserting if you have a spare. May be it would work. Its on your own risk.
Below is the link.
http://www.cisco.com/en/US/prod/collateral/routers/ps259/product_data_sheet0900aecd800fa5be.html
Hope this helps.
Regards,
Pravin

Certification of Cisco UCS B-Series blades

Are there any plans for certification of the Cisco UCS B-series blades?
As far as i can find on the novell website they are already certified for SLES11 from Novell.
Greetings, Stefan Dietz

Hi Stefan,
yes, we will certify CISCO hardware. Hopefully this will happen during the next 6 months. I cannot give more specific information at the moment. The SLES11 certification from SAP will also be available soon (see SLES11 thread in this forum as well).
Thanks,
Hannes

Cisco Aironet 1100 series wireless access point software update!

Hi,
I have a wireless network using 2 cisco aironet 1100 series access points.
From time to time I have problems with connecting a device (Laptop,PC,)to the wireless network.There are onther wireless netwotk that operate around and might be using the same channel.Someone else created the wireless network and I do not know how to access it now to check the configurations on change something.
I cannot conncet my iPhone to the network and I beleive that a software update might solve the problem but I do not know how to do it and where to download it from.
1. How can I update the software and where from?
2.How can I ensure that thare are no interferences and conflicts?
3.How can I ensure that no onther wireless network around is using the same channel?
Thank you in advance.

Sounds good to me. Are you having problems?
Please remeber to rate all replies

Cisco aironet 1200 Series access point dropping clients

We are having an issue where our Cisco Aironet 1220 Series AP is constantly dropping clients. We have 3 APs mounted on a single tower, all out of each others range and freq. There are approximatly 30 clients on each AP. We are noticing an increase in dropped customers (up to 20 at a time). ANy suggestions? This only became an issue in the last few weeks, and nothing major has changed.

Hi
Even I was facing almost the same kind of problem. But in my case it was wired clients to the workgroup bridge 350.
I had done lot of testings and reading at that time to resolve this problem.
However in your case I feel your problem can be resolved by keeping the option "Reliable multicast for Workgroup bridges" disabled in the APs under dot11radio interface settings. This is possibly because the radios cannot associate to more than 20 clients at a time if the option is in the enable mode.
You need to keep this option enabled in a root bridge when you have problems of dropping the wired clients to the workgroup bridge.
By keeping this option enabled, you are actually asking the Root bridges to consider the Workgroup bridges as Infrastructure devices and not as clients thereby making the roots to send all the multicasts to the WGBs. However in that case it losses the efficiency of associating more than 20 clients.
Let me know if this resolves your problem.
Regards

HT3180 My Apple TV is not responding. Screen in black and light indicator blinking fast. Cannot make it work. What should I do?

My Apple TV is not responding. Screen in black and light indicator blinking fast. Cannot make it work. What should I do?

Unplug it from power, wait 10-15 seconds and plug it back in.
If it does not power up properly at that point, restore it via iTunes on the computer.

Macbook Pro does not see Fast Ethernet but works fine with Gigabit Ethernet

Hi to everybody,
It is some time I have a problem connecting my unibody Macbook Pro (late 2008) to the ethernet cables in my office. There are 16 wall jacks in the lab, of which 13 are Fast Ethernet (100 Mbit/s) and 3 are Gigabit Ethernet. No matter what I do, if I connect to the 100 Mbit/s jacks, my Macbook does not see the connection and keeps saying "Cable unplugged". If I switch to a Gigabit jack, then a connection is quickly established.
I have spent one whole afternoon debugging. Here is what I did:
My computer dual boots Mac OS X and Linux. No matter which operating system I use, the problem is the same.
Using different Cat.5 cables does not change the situation (I tried three of them.)
All the 13 Fast Ethernet jacks do not work.
All the 3 Gigabit jacks work smoothly.
What puzzles me is that my computer happly uses the newest technology (Gigabit ethernet) but has problems with the oldest one. Has somebody else experienced the same problem?

After a lot of struggle, I discovered that other people had this very issue as well. It seems that the cause is a faulty Realtek chip used in the ethernet cards of some MacBooks and other brands. There is apparently no way to fix this: I solved my problems by buying a Gigabit Ethernet switch which I connected to the Fast Ethernet wall jack. (Another option might be to use a Ethernet-to-USB adapter - but I did not try this as I have no adapter of this kind.)

Cisco AP 1240AG series Fast Ethernet cannot up

Similar Messages

Maybe you are looking for