Cisco AP 1310 interface status "reset"

any idea why the ap 1310 send the interface to "reset" state:
Feb 28 18:03:00.820 -0600: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot1
1Radio0, changed state to up
*Feb 28 18:03:19.870 -0600: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state
to down
*Feb 28 18:03:19.917 -0600: %LINK-5-CHANGED: Interface Dot11Radio0, changed stat
e to reset
*Feb 28 18:03:20.873 -0600: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot1
1Radio0, changed state to down
*Feb 28 18:03:23.519 -0600: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0,
Associated To AP GDL-GDL1-CR001- 001d.a2b0.3910 [None]
*Feb 28 18:03:23.520 -0600: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state
to up

I think it is seems like bug. Upgrade or downgrade the IOS and try.

Similar Messages

Cisco Aironet 1310 flash memory test

Dear Cisco Support Community
i have a problem on one of my 1310 wireless bridge it is stucked on flash memory test and after resetting the baudrate to 115200
all i see on the bridge is status and Ethernet Leds are blinking green.
Can you please help me?

LED Indications
During access point operation the LEDs provide status information as shown in Table 5-1.
Table 5-1 LED Signals
Message
type
Ethernet
LED
Status
LED
Radio
LED
Meaning
Boot loader status
Green
Green
DRAM memory test.
Amber
Red
Board initialization test
Blinking green
Blinking green
Flash memory test.
Amber
Green
Ethernet initialization test.
Green
Green
Green
Starting Cisco IOS.
Association status
Green
At least one wireless client device is associated with the unit.
Blinking green
No client devices are associated; check the unit's SSID and WEP settings.
Operating status
Green
Blinking green
Transmitting/receiving radio packets.
Green
Ethernet link is operational.
Blinking green
Transmitting/receiving Ethernet packets.
Boot loader errors
Red
Red
DRAM memory test failure.
Red
Red
File system failure.
Red
Red
Ethernet failure during image recovery.
Amber
Green
Amber
Boot environment error.
Red
Green
Red
No Cisco IOS image file.
Amber
Amber
Amber
Boot failure.
Operation errors
Green
Blinking amber
Maximum retries or buffer full occurred on the radio.
Blinking amber
Transmit/receive Ethernet errors.
Blinking amber
General warning.
Configuration reset
Amber
Resetting the configuration options to factory defaults.
Failure
Red
Red
Red
Firmware failure; try disconnecting and reconnecting unit power.
Firmware upgrade
Red
Loading new firmware image.
Controller status
Alternating green, red, and amber1
Connecting to the controller. Note If the access point remains in this mode for more than five minutes, the access point is unable to find the controller. Ensure a DHCP server is available or that controller information is configured on the access point.
Message
type
Ethernet
LED
Status
LED
Radio
LED
Meaning
1 This status indication has the highest priority and overrides other status indications.

Configuration of a Point to MultiPoint link with Cisco Aironet 1310 bridges

Hi All,
The previous problem of which I started another conversation here:
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddba023
somehow dissapeared. It could have been a problem of interferences.
I have another issue with other (multipoint) wireless WAN link, which I hope has a solution.
On the central node, we have an Cisco Aironet 1310 bridge configured as root-bridge. It has a panel of four vertical polarity 17 dBi panel 90? antennas, with more than enough gain (there is a 250 mWatts 802.11 b/g amplifier, before the 4-way splitter) and excellent line of sight to three remote bridges.
The three (03) remote bridges are also Aironet 1310 models, confidured as non-root-bridges.
The problem we have is that it seems that when the three remote links operate concurrently the amount of lost packets is huge. When I shutdown the radio interfaces of two bridges, the remaining bridge makes an excellent link with the central node.
It seems that some hours are more critical than others, also the links operate much worse when there is some (small) network traffic in them.
I have read the 1310 manuals, and I can't find a sample configuration for point to multi-point links.
Does someone knows what radio interface configuration should I need to use to establish better quality communication?
I mean, perhaps the 1 x root - 3 x no root configuration is not recommendable for the multipoint link configuration.
Any hints will be welcome.
Best Regards,
Igor Sotelo.

Hi All,
Thank you for the information. I configured the distance on the root bridges, but the links showed instability.
I'm using a bi-directional amplifier. It has two pieces. According to the manuals, one is installed indoors, the other outdoors. I'm not sure if the indoors piece has the transmition module or it's only the injector.
We could establish connection at 7 km (around 4 milles) distance from the central point, using 24 dBi antennas on the other side.
However, we have issues with a near located point that is only 1.2 Km (around 0.8 milles) away and has a 13 dBi integrated patch antenna. The signal strenght value we get there is in the -62 to -68 dBm range, and is noticiably (5-10 dBm) lower than the strenght we get at other points of the link. And I have trouble establishing a high quality link with that point, using OFDM modulation. I tend to think that if I remove the amplifier I'm not going to reach that point at all. The EIRP on the central iste is 34 dBm / 2.5 watts, without amplifier it would be 26 dBm / 0.4 watts.
On the opposite sites the EIRP is 33 dBm / 2 watts using CCK or 28 dBm / 0.63 watts using OFDM.
When one looks at the central site from that point, an Motorola Canopy with passive reflector (EIRP 48 dBm or around 64 watts) can be seen. It doesn't have the same direction, but the opposite site must be large distance and could interfere with my wireless network. Attached is an amplified photo of the view. It's safe to assume that the Canopy operates in the 2.4 GHz frequency range.
Once I connect the point at 1.2 Km, the multipoint link loses its quality, and soon the lost packets get too frequent.
The CCK seems to be much more interfered than OFDM, I guess because of that canopies.
Another thing I'm wondering about is if the Aironet 1310 can continuosly switch CCK-OFDM over the same point - multipoint link, without losing packets.
What other parameters should I tweak? Is there a way to avoid interferences fromt the canopy?
I would like to apply 100 mWatts local power using the radio with OFDM, but it seems that's not possible.
Best Regards,
Igor Sotelo.

Sh Interface status

Hi! What's the command for sh interface status in CAT OS?
Thks!

Hi Friend,
You will not get the exact output as you get is IOS but you can take the output from this commands
sh port
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_8_5/cmd_ref/sh_p_sn.htm#wp1715472
sh mac
Have a look at this for details on "sh mac" command
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_8_5/cmd_ref/sh_ml_n.htm#wp1028548
HTH, if yes please rate the post.
Ankur

Show interface status (IOS layer 2switch)

Is it possible to modify the width of the column containing the description of the interfaces when I issue the "show interface status?" on IOS cisco switches?

I don't believe so but you can type show interface description if you want to see the entire description that is associated to the port.
HTH,
Edison.

Unable to enter "Conf T" on Cisco Aironet 1310

Hello Experts,
I have a question about Cisco Aironet 1310 AP, the problem I am getting is that I am unable to enter the conf t mode to configure the AP. I am not sure what could be the problem. I have IOS 12.3 running on it.
Please help

Hey Steve,
Its k9w8, this is what I see on sh ver
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:45 by alnguyen
ROM: Bootstrap program is C1310 boot loader
BOOTLDR: C1310 Boot Loader (C1310-BOOT-M) Version 12.3(2)JA4, RELEASE SOFTWARE (fc1)
AP1310-MASJID uptime is 1 week, 2 days, 9 hours, 38 minutes
System returned to ROM by power-on
System image file is "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx"
cisco AIR-LAP1310G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1536U060
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface

Cisco ISE Web interface Login

Hi,
Can anyone help me in resetting the Cisco ISE web interface password. I'm able to login to CLI of ISE but couldnt use the same credentials to login to web interface. Is there any way to reset this web interface password through ISE CLI?
Thanks
Daniel

Daniel,
Just ran across your question, the answer is you can have login credentials for the cli but that is seperate from the gui. The way I understand it is once you get to the gui for the first time user is admin and password is cisco. At this point you are required to put in a new password. Once in the gui other users can be created for the gui.
Erik

Gigabit interface status faulty please help

When I do a show interface status on 4500 switch I got a status faulty
I did never see such thing
Port- Name-Status-Vlan-Duplex-Speed Type
Gi2/7-jsh3 faulty 188 full XXBaseSX
Could you please help?
Thanks a lot

this usually indicates the port is faulty (bad; not working; will not work)
this may have been set via the POST of the device. the internal tests failed and the port was marked FAULTY.
this could also be the result of a good port simply went bad for some unknown reason.
try to disable/reEnable the port. will probably still say faulty. (cannot initialize a faulty port)
try to reset the blade the port is on, or the supervisor if it resides on that.
do a "show test" (catOS) to see what the POST found when it did its powerOnSelfTests.
i've seen plenty of FAULTY ports and 99% of the time, the port is simply bad and must be replaced. (usually an ASIC or the likes)

How many clients can connect through cisco AP 1310 in wireless network ?

I had setup wireless network with
wlc4402,cisco AP 1310.1131 and 1242 and Cisco acs 4.1.My problem is only 30 clients connect through Cisco AP 1310 at a time.I can not connect more than 30 clients at a time.What is the issue in wireless network?please reply .
Thanks and regards
By
D.Anbudurai

WIRELESS > 802.11 > RRM
How can do that setting ? Can you reply with
some brief steps? And also I want to know how
many clients can connect in wireless network at
a time exactly through cisco aps?
Thanks and regards
d.anbudurai

Cisco Aironet 1310 series

hello all,
I have a cisco Aironet 1310 series which am having problem with the signal strength. This box came with 8 dbi Omni antenna gain and am told this can go upto 5km raduis. After configuring this equipment, i could not get a link when i move 500 meters. Please find attached the configs on the box. Any help given would be very much appreciated. Thank You

This 5KM distance is only going to be applicable in bridging situations. The following link shows how to use the distance calculations based on devices: http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
In theory, if you had a really strong direction antenna on your client you'd be able to get the 1310 as an access Point from 5km, but you'd need perfect line-of-site and you wouldn't be mobile...
As others had mentioned, if you're looking for an access point situation with that kind of range, then you need WiMax....
but if it is bridging you want, its just a matter of getting the other link to see this one (with a good enough antenna)

Cisco SUP MGMT Interface Support L2 switchport mode?

Does the Cisco Supervisor MGMT interface support to be converted to a switchport to be assigned to a specific VLAN? The same question for 3750 switches and other switches.

No. They do need to have an IP address configured as they are actually routed ports.
The address needs to be in the subnet associated with the VLAN it plugs into in the switching infrastructure.

Does Cisco Media Services Interface mark RTP and Signaling packets regardless of Cisco Prime Collaboration/MediaNet Deployment?

Hi there,
I'm deploying Cisco UC Integration Lync 9.2(5). There's a QoS portion which states that you can install Cisco Media Services Interface on the user's PC and is to be used with Cisco Prime Collaboration or MediaNet:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucilync/9/CUCI_BK_C0545A41_00_cisco-uc-integration-for-microsoft/CUCI_BK_C0545A41_00_cisco-uc-integration-for-microsoft_chapter_010.html#CUCI_CN_IDBE72E9_00
If we don't have Cisco Prime Collaboration or MediaNet, does Cisco Media Services Interface mark RTP and Siganling packets on the outbound regardless? Or do I have to manually set the DSCP values for the PC?
Thanks,
John

When you were placing the internal test calls, where was your phone located? The RTP streams are usually only set up between the two endpoints (assuming no transcoder or MTP is used).
Have you have already checked calls between IP phones at your central site (where Unity is located) and IP Phones at site A? Are these working fine? If not, then it's likely you do have a QoS issue over the WAN to Site A.
Have you confirmed whether or not calls from the PSTN gateway at site A experience any voice QoS issues when transferred to an IP Phone at the central site?
Is the same codec is being used for the MGCP gateway as for IP Phones at that site (check the Region settings for the Device Pool it's in)?
If these things have all been checked, then you may want to consider collecting a simultaneous sniffer trace from each end of a single call, and comparing what's seen at the two endpoints.
Kind regards,
Craig

Aironet 1310 interface dot11 0 stuck in reset

Hi trying to connect two APs with one being root and the other non root. After configuring, the wireless interface on the non root remains stuck
int reset mode. Below is the error message i get and have tried and cant find out what the problem is.
%DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
Will appreciate any help. thanks

As per dmantill mention once we have a 1310 in root bridge and the other one in non root bridge the non root bridge will not enable the radio until it sees a good signal from the root bridge and its status will be reset down.
Remember that we have 2 types of 1310 the ones with build in antennas and the ones with no build in antenna and require and external antenna connected to it.
To know if your unit has a build in antenna or not the part number will not include a (-R) if it has a (–R) it means that the unit does not have a build in antenna.
Also remember that when we work with bridges we need to set them in install mode (install root bridge and install non root bridge)this mode will only allow the units to associate to each other and not pass traffic and the led’s on the back of the unit will stop works as usual and help us for antenna alignment between the units.
Here is the link that lets us know what each sequence we get on the leds once in install mode to know how god the antenna aliment or signal is.
http://www.cisco.com/en/US/docs/wireless/access_point/1300/installation/guide/130h_c3.html#wp1056656
Also remember that when working with bridges by defaults the units are set to work at full power and this would create 2 scenarios.
For example, if the units are able to cover up to 5km with full power if the distance between the units is more than 5 km then they will not be able connect and if the distance is shorter than 5 km let’s say 1 km and we leave the units at full power there is going to be too much interface and signal to noise on the connection due to the short distance between the units and at the end this could make the units not see a good signal between them.
For instance lets say we are on a football field and each of us is on a touchdown side and for us to be able to hear each other we need to scream to each other, but if we then walk to the center of the field and we keeping screaming we are going to hear ourselves but we will not be able to understand what we are saying to each other and we will need to lower our voice.
Here is the outdoor range calculation utility to check what is the exact distance we can cover with a unit and at an specific data rate.
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
Just in case usefull links.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml
http://www.cisco.com/en/US/products/hw/wireless/ps469/products_tech_note09186a0080508551.shtml
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_q_and_a_item09186a008015502c.shtml

Dot11Radio0 Interface in reset/down status

Hi,
I have the next problem.
The interface Dot11radio0 is always in reset / down status.
I can't link both AP.
They both are cisco AIR-AP1252AG-E-K9.
This have been working fine for 18 months, but this week suddenly went down.
I updated yesterday one of the APs to a new version, from the 12.4.10b-JDA3(GD) to the c1250-k9w7-tar.124-25d.JA1.tar but the problem was no fixed.
the other AP has 12.4.21a-JY(ED).
I've changes the role of the APs, the one with was root-bridge changed to non root-bridge and the one with was non root-bridge become root bridge.
Doing this, I changed the status of the interfaces, the AP with had interface dot11radio0 up up, become in reset down, and the AP that previously was in reset down, become in up up.
In the show log I see that the problem is:
Dot11Radio0, cannot associate: Authenticating
Interface Dot11Radio0, cannot associate: No Response
I leave the confs here.
Please, help me.

Hi Surendra,
I'm getting:
The bug ID CSCtc23789ï»¿ does not exist. Please verify the bug ID and try again. If you feel you reached this message in error, please send us
feedback
including the bug ID in question. Thank you.
What's the BugID and I can look it up. I will rate your post!

AP 1252 dot11radio interface status shows RESET

Hi,
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version
C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
BVI1                       <ipaddress>       YES DHCP   up                    up
Dot11Radio0                unassigned      YES TFTP   reset                 down
Dot11Radio0.102            unassigned      YES unset reset                 down
Dot11Radio0.104            unassigned      YES unset reset                 down
Dot11Radio0.105            unassigned      YES unset reset                 down
Dot11Radio0.108            unassigned      YES unset reset                 down
Dot11Radio1                unassigned      YES TFTP   administratively down down
GigabitEthernet0           unassigned      YES TFTP   up                    up
GigabitEthernet0.102       unassigned      YES unset up                    up
GigabitEthernet0.104       unassigned      YES unset up                    up
GigabitEthernet0.105       unassigned      YES unset up                    up
GigabitEthernet0.106       unassigned      YES unset up                    up
GigabitEthernet0.108       unassigned      YES unset up                    up
ap03#
Due to this the clientsa re not getting associated.
I tried rebooting the AP; shut the dot11radio0 interface and unshut it; verified the switch end duplex speed settings. Looks good.
Can anyone suggest me how to proceed?
Thankyou.

Hi,
Yes the Access Point was working fine all these days and for the last one week, I am facing this problem. Please find the running configuration of the Access point as below..
Building configuration...
Current configuration : 8275 bytes
version 12.4
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname ap03
logging buffered 65536 notifications
enable secret 5 $1$.WG7$dvJpY1XHuixBk3wA4sfR3/
aaa new-model
aaa group server radius rad_eap
server auth-port 1812 acct-port 1813
aaa authentication login default group tacacs+ local enable
aaa authentication login eap_methods group rad_eap
aaa authorization exec default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa session-id common
clock timezone MST -7
clock summer-time MDT recurring
ip rcmd rsh-enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host datacom datacom enable
ip domain list u04129.albertsons.com
ip domain list albertsons.com
ip domain name u04129.albertsons.com
ip name-server
ip ssh time-out 90
dot11 activity-timeout unknown default 28800
dot11 ssid Courage-34idkeysNCswuZue3765#%@&
   vlan 102
   authentication open eap eap_methods
   authentication key-management wpa
dot11 ssid Freedom-jKb%&552en@546AsdfG65eD
   vlan 105
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
dot11 ssid Galaxy-73j4CA58fd66y3lKICK#%@&*
   vlan 104
   authentication open
dot11 ssid Quake-35f8d4q9e5@365%lFh&ju#ef2
   vlan 108
   authentication open eap eap_methods
   authentication key-management wpa
dot11 holdoff-time 60
dot11 arp-cache optional
power inline negotiation prestandard source
dot1x timeout reauth-period server
username Cisco password 7 02250D480809
username ggg privilege 15 secret 5 $1$E4Ms$78SOM7s3gZ8QxU.mlnEpj.
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 104 key 1 size 128bit 7 80B78765DD670039FE1557E4BFB4 transmit-key
encryption vlan 104 mode wep mandatory
encryption vlan 108 mode ciphers tkip
encryption vlan 102 mode ciphers tkip
encryption vlan 105 mode ciphers tkip
ssid Courage-34idkeysNCswuZue3765#%@&
ssid Freedom-jKb%&552en@546AsdfG65eD
ssid Galaxy-73j4CA58fd66y3lKICK#%@&*
ssid Quake-35f8d4q9e5@365%lFh&ju#ef2
power local 17
packet retries 64 drop-packet
no preamble-short
channel 2412
station-role root
beacon dtim-period 4
no dot11 extension aironet
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.102
encapsulation dot1Q 102
no ip route-cache
no cdp enable
bridge-group 102
bridge-group 102 subscriber-loop-control
bridge-group 102 input-type-list 201
bridge-group 102 output-type-list 201
bridge-group 102 port-protected
bridge-group 102 block-unknown-source
no bridge-group 102 source-learning
no bridge-group 102 unicast-flooding
bridge-group 102 spanning-disabled
interface Dot11Radio0.104
encapsulation dot1Q 104
no ip route-cache
no cdp enable
bridge-group 104
bridge-group 104 subscriber-loop-control
bridge-group 104 input-type-list 201
bridge-group 104 output-type-list 201
bridge-group 104 port-protected
bridge-group 104 block-unknown-source
no bridge-group 104 source-learning
no bridge-group 104 unicast-flooding
bridge-group 104 spanning-disabled
interface Dot11Radio0.105
encapsulation dot1Q 105
no ip route-cache
no cdp enable
bridge-group 105
bridge-group 105 subscriber-loop-control
bridge-group 105 input-type-list 201
bridge-group 105 output-type-list 201
bridge-group 105 port-protected
bridge-group 105 block-unknown-source
no bridge-group 105 source-learning
no bridge-group 105 unicast-flooding
bridge-group 105 spanning-disabled
interface Dot11Radio0.108
encapsulation dot1Q 108
no ip route-cache
no cdp enable
bridge-group 108
bridge-group 108 subscriber-loop-control
bridge-group 108 input-type-list 201
bridge-group 108 output-type-list 201
bridge-group 108 port-protected
bridge-group 108 block-unknown-source
no bridge-group 108 source-learning
no bridge-group 108 unicast-flooding
bridge-group 108 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.102
encapsulation dot1Q 102
no ip route-cache
bridge-group 102
no bridge-group 102 source-learning
bridge-group 102 spanning-disabled
interface GigabitEthernet0.104
encapsulation dot1Q 104
no ip route-cache
bridge-group 104
no bridge-group 104 source-learning
bridge-group 104 spanning-disabled
interface GigabitEthernet0.105
encapsulation dot1Q 105
no ip route-cache
no cdp enable
bridge-group 105
no bridge-group 105 source-learning
bridge-group 105 spanning-disabled
interface GigabitEthernet0.106
encapsulation dot1Q 106 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.108
encapsulation dot1Q 108
no ip route-cache
no cdp enable
bridge-group 108
no bridge-group 108 source-learning
bridge-group 108 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
no logging trap
access-list 1421 permit
access-list 1421 permit
access-list 1421 permit 0.0.0.255
access-list 1421 permit 0.0.0.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 deny   any
access-list 201 permit 0x0800 0x0000
access-list 201 permit 0x0806 0x0000
access-list 201 deny   0x0000 0xFFFF
snmp-server view NCC mib-2 included
snmp-server community TROUbleIStrouBLE view NCC RO
snmp-server community CHECKtheMAIL RO
snmp-server community HAVocREEk RW
snmp-server community 1aPe3nLnmDt4yVYmbgWoUVjJYz1 view NCC RO 1421
snmp-server community 1aUQ5DAIH2bTBlvJg6RFS5qfsr RO 1421
snmp-server community 1OGgsN21DI4q01QeeIhJGF961 RW 1421
snmp-server enable traps tty
tacacs-server host
tacacs-server host
tacacs-server directed-request
tacacs-server key 7 110A1D5347415C5B53737F7D2E26
radius-server attribute 32 include-in-access-req format %h
radius-server host auth-port 1812 acct-port 1813 key 7 10190C4A533C07185D50721569013D3C3638022F4E0E42400102773D0D481A5E0E
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 5 15
sntp server
end

Cisco AP 1310 interface status "reset"

Similar Messages

Maybe you are looking for