Cisco ASA 5505 Dual-ISP Backup VPN
I am trying to create a backup tunnel from an ASA 5505 to a pix 501 in the case of the Main ISP failing. The Pix external side will stay the same, but not quite sure how I can create a new crypto map and have it use the Backup ISP interface without bringing down the main tunnel.
My first thought was to add the following crypto map to the configuration below:
crypto map outside_map 2 match address outside_1_cryptomap
crypto map outside_map 2 set peer 9.3.21.13
crypto map outside_map 2 set transform-set ESP-DES-MD5
crypto map outside_map interface backupisp -->but this would break the current tunnel.
NYASA# sh run
: Saved
ASA Version 7.2(4)
hostname NYASA
domain-name girls.org
enable password CHwdJ2WMUcjxIIm8 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 10.1.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 9.17.5.8 255.255.255.240
interface Vlan3
description Backup ISP
nameif backupisp
security-level 0
ip address 6.27.9.5 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended permit icmp any any source-quench
access-list outside_access_in extended permit icmp any any unreachable
access-list outside_access_in extended permit icmp any any time-exceeded
access-list outside_access_in extended permit icmp any any
access-list inside_nat0_outbound extended permit ip 10.1.2.0 255.255.255.0 10.1.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.1.2.0 255.255.255.0 10.1.100.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 10.1.2.0 255.255.255.0 10.1.1.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 10.1.2.0 255.255.255.0 10.1.100.0 255.255.255.0
access-list 150 extended permit ip any host 10.1.2.27
access-list 150 extended permit ip host 10.1.2.27 any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu backupisp 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
global (backupisp) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 9.17.5.7 1 track 1
route backupisp 0.0.0.0 0.0.0.0 6.27.9.1 254
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa authentication ssh console LOCAL
http server enable
http 10.1.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sla monitor 10
type echo protocol ipIcmpEcho 4.2.2.2 interface outside
num-packets 3
timeout 1000
frequency 3
sla monitor schedule 10 life forever start-time now
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer 9.3.21.13
crypto map outside_map 1 set transform-set ESP-DES-MD5
crypto map outside_map interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
crypto isakmp nat-traversal 20
track 1 rtr 10 reachability
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 60
console timeout 0
management-access inside
username ptiadmin password BtOLil2gR0VaUjfX encrypted privilege 15
tunnel-group 9.4.21.13 type ipsec-l2l
tunnel-group 9.4.21.13 ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:22bb60b07c4c1805b89eb2376683f861
: end
NYASA#
Thanks in advance.
In that case is the PIX who needs two peers (to the ASA).
The ASA will requiere the crypto map to be applied to the backup interface as well (as you mentioned)
crypto map outside_map interface backupisp -->but this would break the current tunnel.
The above command should not break the current tunnel (if the route to reach the other end goes out via the primary interface).
Additionally you need IP SLA configured in the ASA to allow it to use the primary connection and fallback to the backup connection to build-up the tunnel (as well to use again the primary interface when it recovers).
Federico.
Similar Messages
-
Cisco ASA 5505 Site to Site VPN
Hello All,
First time posting to the forums. I've been working with Cisco ASA 5505 for a number of months and recently I purchased a 2nd ASA with the goal of setting up Site to Site VPN tunnel. It look so simple from the number of videos that I have watched on the internet. But when I have done it suprise suprise it didn't work for me ... I have deleted the tunnels a number of times and attempted to recreate them. I am using the VPN wizard in the ADM to create the tunnel. Both the asa are 5505 and have the same same firmware etc.
I would appreciate any help that can be directed towards this issue please. Slowly losing my mind
Please see details below:
Both ADM are 7.1
IOS
ASA 1
aved
ASA Version 9.0(1)
hostname PAYBACK
enable password HSMurh79NVmatjY0 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
ip local pool VPN1 192.168.50.1-192.168.50.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
description Trunk link to SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan2
nameif outside
security-level 0
ip address 92.51.193.158 255.255.255.252
interface Vlan10
nameif inside
security-level 100
ip address 192.168.10.1 255.255.255.0
interface Vlan20
nameif servers
security-level 100
ip address 192.168.20.1 255.255.255.0
interface Vlan30
nameif printers
security-level 100
ip address 192.168.30.1 255.255.255.0
interface Vlan40
nameif wireless
security-level 100
ip address 192.168.40.1 255.255.255.0
banner login line Welcome to Payback Loyalty Systems
boot system disk0:/asa901-k8.bin
ftp mode passive
clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
dns domain-lookup outside
dns domain-lookup inside
dns domain-lookup servers
dns domain-lookup printers
dns domain-lookup wireless
dns server-group DefaultDNS
name-server 83.147.160.2
name-server 83.147.160.130
same-security-traffic permit inter-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network ftp_server
object network Internal_Report_Server
host 192.168.20.21
description Automated Report Server Internal Address
object network Report_Server
host 89.234.126.9
description Automated Report Server
object service RDP
service tcp destination eq 3389
description RDP to Server
object network Host_QA_Server
host 89.234.126.10
description QA Host External Address
object network Internal_Host_QA
host 192.168.20.22
description Host of VM machine for QA
object network Internal_QA_Web_Server
host 192.168.20.23
description Web Server in QA environment
object network Web_Server_QA_VM
host 89.234.126.11
description Web server in QA environment
object service SQL_Server
service tcp destination eq 1433
object network Demo_Server
host 89.234.126.12
description Server set up to Demo Product
object network Internal_Demo_Server
host 192.168.20.24
description Internal IP Address of Demo Server
object network NETWORK_OBJ_192.168.20.0_24
subnet 192.168.20.0 255.255.255.0
object network NETWORK_OBJ_192.168.50.0_26
subnet 192.168.50.0 255.255.255.192
object network NETWORK_OBJ_192.168.0.0_16
subnet 192.168.0.0 255.255.0.0
object service MSSQL
service tcp destination eq 1434
description MSSQL port
object network VPN-network
subnet 192.168.50.0 255.255.255.0
object network NETWORK_OBJ_192.168.50.0_24
subnet 192.168.50.0 255.255.255.0
object service TS
service tcp destination eq 4400
object service TS_Return
service tcp source eq 4400
object network External_QA_3
host 89.234.126.13
object network Internal_QA_3
host 192.168.20.25
object network Dev_WebServer
host 192.168.20.27
object network External_Dev_Web
host 89.234.126.14
object network CIX_Subnet
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.10.0_24
subnet 192.168.10.0 255.255.255.0
object network NETWORK_OBJ_84.39.233.50
host 84.39.233.50
object network NETWORK_OBJ_92.51.193.158
host 92.51.193.158
object network NETWORK_OBJ_192.168.100.0_24
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq ftp
service-object tcp destination eq netbios-ssn
service-object tcp destination eq smtp
service-object object TS
object-group network Payback_Internal
network-object 192.168.10.0 255.255.255.0
network-object 192.168.20.0 255.255.255.0
network-object 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
service-object tcp destination eq www
service-object tcp destination eq https
service-object object TS
service-object object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object object RDP
service-object tcp destination eq www
service-object tcp destination eq https
object-group service DM_INLINE_SERVICE_5
service-object object MSSQL
service-object object RDP
service-object object TS
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service DM_INLINE_SERVICE_6
service-object object TS
service-object object TS_Return
service-object tcp destination eq www
service-object tcp destination eq https
access-list outside_access_in remark This rule is allowing from internet to interal server.
access-list outside_access_in remark Allowed:
access-list outside_access_in remark FTP
access-list outside_access_in remark RDP
access-list outside_access_in remark SMTP
access-list outside_access_in remark Net Bios
access-list outside_access_in remark SQL
access-list outside_access_in remark TS - 4400
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any4 object Internal_Report_Server
access-list outside_access_in remark Access rule to internal host QA
access-list outside_access_in remark Allowed:
access-list outside_access_in remark HTTP
access-list outside_access_in remark RDP
access-list outside_access_in extended permit tcp any4 object Internal_Host_QA eq www
access-list outside_access_in remark Access to INternal Web Server:
access-list outside_access_in remark Allowed:
access-list outside_access_in remark HTTP
access-list outside_access_in remark RDP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 any4 object Internal_QA_Web_Server
access-list outside_access_in remark Rule for allowing access to Demo server
access-list outside_access_in remark Allowed:
access-list outside_access_in remark RDP
access-list outside_access_in remark MSSQL
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any4 object Internal_Demo_Server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
access-list outside_access_in remark Access for Development WebServer
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
access-list Payback_VPN_splitTunnelAcl standard permit 192.168.20.0 255.255.255.0
access-list outside_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging console informational
logging asdm informational
logging from-address
[email protected]
logging recipient-address
[email protected]
level alerts
mtu outside 1500
mtu inside 1500
mtu servers 1500
mtu printers 1500
mtu wireless 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711-52.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source dynamic any interface
nat (wireless,outside) source dynamic any interface
nat (servers,outside) source dynamic any interface
nat (servers,outside) source static Internal_Report_Server Report_Server
nat (servers,outside) source static Internal_Host_QA Host_QA_Server
nat (servers,outside) source static Internal_QA_Web_Server Web_Server_QA_VM
nat (servers,outside) source static Internal_Demo_Server Demo_Server
nat (servers,outside) source static NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 destination static NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 no-proxy-arp route-lookup
nat (servers,outside) source static Internal_QA_3 External_QA_3
nat (servers,outside) source static Dev_WebServer External_Dev_Web
nat (inside,outside) source static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 84.39.233.50
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 77.75.100.208 255.255.255.240 outside
ssh 192.168.10.0 255.255.255.0 inside
ssh 192.168.40.0 255.255.255.0 wireless
ssh timeout 5
console timeout 0
dhcpd dns 192.168.0.1
dhcpd auto_config outside
dhcpd address 192.168.10.21-192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
dhcpd option 15 ascii paybackloyalty.com interface inside
dhcpd enable inside
dhcpd address 192.168.40.21-192.168.40.240 wireless
dhcpd dns 192.168.20.21 83.147.160.2 interface wireless
dhcpd update dns interface wireless
dhcpd option 15 ascii paybackloyalty.com interface wireless
dhcpd enable wireless
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy Payback_VPN internal
group-policy Payback_VPN attributes
vpn-simultaneous-logins 10
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Payback_VPN_splitTunnelAcl
group-policy DfltGrpPolicy attributes
dns-server value 83.147.160.2 83.147.160.130
vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
group-policy GroupPolicy_84.39.233.50 internal
group-policy GroupPolicy_84.39.233.50 attributes
vpn-tunnel-protocol ikev1 ikev2
username Noelle password XB/IpvYaATP.2QYm encrypted
username Noelle attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Eanna password vXILR9ZZQIsd1Naw encrypted privilege 0
username Eanna attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Michael password qpbleUqUEchRrgQX encrypted
username Michael attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Danny password .7fEXdzESUk6S/cC encrypted privilege 0
username Danny attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Aileen password tytrelqvV5VRX2pz encrypted privilege 0
username Aileen attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Aidan password aDu6YH0V5XaxpEPg encrypted privilege 0
username Aidan attributes
vpn-group-policy Payback_VPN
service-type remote-access
username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
username shane.c password iqGMoWOnfO6YKXbw encrypted
username shane.c attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Shane password uYePLcrFadO9pBZx encrypted
username Shane attributes
vpn-group-policy Payback_VPN
service-type remote-access
username James password TdYPv1pvld/hPM0d encrypted
username James attributes
vpn-group-policy Payback_VPN
service-type remote-access
username mark password yruxpddqfyNb.qFn encrypted
username mark attributes
service-type admin
username Mary password XND5FTEiyu1L1zFD encrypted
username Mary attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Massimo password vs65MMo4rM0l4rVu encrypted privilege 0
username Massimo attributes
vpn-group-policy Payback_VPN
service-type remote-access
tunnel-group Payback_VPN type remote-access
tunnel-group Payback_VPN general-attributes
address-pool VPN1
default-group-policy Payback_VPN
tunnel-group Payback_VPN ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 general-attributes
default-group-policy GroupPolicy_84.39.233.50
tunnel-group 84.39.233.50 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map global-class
match default-inspection-traffic
policy-map global-policy
class global-class
inspect dns
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect pptp
inspect rsh
inspect rtsp
inspect sip
inspect snmp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect xdmcp
inspect icmp error
inspect icmp
service-policy global-policy global
smtp-server 192.168.20.21
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1
ASA 2
ASA Version 9.0(1)
hostname Payback-CIX
enable password HSMurh79NVmatjY0 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
description This port connects to VLAN 100
switchport access vlan 100
interface Ethernet0/2
interface Ethernet0/3
switchport access vlan 100
interface Ethernet0/4
switchport access vlan 100
interface Ethernet0/5
switchport access vlan 100
interface Ethernet0/6
switchport access vlan 100
interface Ethernet0/7
switchport access vlan 100
interface Vlan2
nameif outside
security-level 0
ip address 84.39.233.50 255.255.255.240
interface Vlan100
nameif inside
security-level 100
ip address 192.168.100.1 255.255.255.0
banner login line Welcome to Payback Loyalty - CIX
ftp mode passive
clock summer-time gmt/idt recurring last Sun Mar 1:00 last Sun Oct 2:00
dns domain-lookup outside
dns domain-lookup inside
dns server-group defaultDNS
name-server 8.8.8.8
name-server 8.8.4.4
same-security-traffic permit inter-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network CIX-Host-1
host 192.168.100.2
description This is the host machine of the VM servers
object network External_CIX-Host-1
host 84.39.233.51
description This is the external IP address of the host server for the VM server
object service RDP
service tcp source range 1 65535 destination eq 3389
object network Payback_Office
host 92.51.193.158
object service MSQL
service tcp destination eq 1433
object network Development_OLTP
host 192.168.100.10
description VM for Eiresoft
object network External_Development_OLTP
host 84.39.233.52
description This is the external IP address for the VM for Eiresoft
object network Eiresoft
host 146.66.160.70
description DBA Contractor
object network External_TMC_Web
host 84.39.233.53
description Public Address of TMC Webserver
object network TMC_Webserver
host 192.168.100.19
description Internal Address of TMC Webserver
object network External_TMC_OLTP
host 84.39.233.54
description Targets OLTP external IP
object network TMC_OLTP
host 192.168.100.18
description Targets interal IP address
object network External_OLTP_Failover
host 84.39.233.55
description Public IP of OLTP Failover
object network OLTP_Failover
host 192.168.100.60
description Server for OLTP failover
object network Servers
subnet 192.168.20.0 255.255.255.0
object network Wired
subnet 192.168.10.0 255.255.255.0
object network Wireless
subnet 192.168.40.0 255.255.255.0
object network NETWORK_OBJ_192.168.100.0_24
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.10.0_24
subnet 192.168.10.0 255.255.255.0
object network Eiresoft_2nd
host 137.117.217.29
description Eiresoft 2nd IP
object network Dev_Test_Webserver
host 192.168.100.12
description Dev Test Webserver Internal Address
object network External_Dev_Test_Webserver
host 84.39.233.56
description This is the PB Dev Test Webserver
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_2
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_3
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_4
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_5
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_6
service-object object MSQL
service-object object RDP
object-group network Payback_Intrernal
network-object object Servers
network-object object Wired
network-object object Wireless
object-group service DM_INLINE_SERVICE_7
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_8
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_9
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_10
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_11
service-object object RDP
service-object tcp destination eq ftp
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-Host-1
access-list outside_access_in remark Development OLTP from Payback Office
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP
access-list outside_access_in remark Access for Eiresoft
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver
access-list outside_access_in remark Access to OLTP for target from Payback Office
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover
access-list outside_access_in remark This is allowing access from Eiresoft to the OLTP Failover server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover
access-list outside_access_in remark Access for the 2nd IP from Eiresoft
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP
access-list outside_access_in remark Access from the 2nd Eiresoft IP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP
access-list outside_cryptomap extended permit ip 192.168.100.0 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source dynamic any interface
nat (inside,outside) source static CIX-Host-1 External_CIX-Host-1
nat (inside,outside) source static Development_OLTP External_Development_OLTP
nat (inside,outside) source static TMC_Webserver External_TMC_Web
nat (inside,outside) source static TMC_OLTP External_TMC_OLTP
nat (inside,outside) source static OLTP_Failover External_OLTP_Failover
nat (inside,outside) source static Dev_Test_Webserver External_Dev_Test_Webserver
nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 92.51.193.156 255.255.255.252 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 92.51.193.158
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 77.75.100.208 255.255.255.240 outside
ssh 92.51.193.156 255.255.255.252 outside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy GroupPolicy_92.51.193.158 internal
group-policy GroupPolicy_92.51.193.158 attributes
vpn-tunnel-protocol ikev1 ikev2
username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 general-attributes
default-group-policy GroupPolicy_92.51.193.158
tunnel-group 92.51.193.158 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHi,
Thanks for the help to date
I now have the Site to Site working but there is one little issue I have. If I try to RD to a server through the tunnel it will not allow connection on the first attempt however if I ping that host and then attempt to RD it will allow the connection. It looks like the host is asleep until it receives traffic through the tunnel. Is this thje correct behaviour.
See below the details:
ASA1:
hostname PAYBACK
enable password HSMurh79NVmatjY0 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
ip local pool VPN1 192.168.50.1-192.168.50.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
description Trunk link to SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan2
nameif outside
security-level 0
ip address XX.XX.XX.XX 255.255.255.252
interface Vlan10
nameif inside
security-level 100
ip address 192.168.10.1 255.255.255.0
interface Vlan20
nameif servers
security-level 100
ip address 192.168.20.1 255.255.255.0
interface Vlan30
nameif printers
security-level 100
ip address 192.168.30.1 255.255.255.0
interface Vlan40
nameif wireless
security-level 100
ip address 192.168.40.1 255.255.255.0
banner login line Welcome to Payback Loyalty Systems
boot system disk0:/asa901-k8.bin
ftp mode passive
clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
dns domain-lookup outside
dns domain-lookup inside
dns domain-lookup servers
dns domain-lookup printers
dns domain-lookup wireless
dns server-group DefaultDNS
name-server 83.147.160.2
name-server 83.147.160.130
same-security-traffic permit inter-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network ftp_server
object network Internal_Report_Server
host 192.168.20.21
description Automated Report Server Internal Address
object network Report_Server
host 89.234.126.9
description Automated Report Server
object service RDP
service tcp destination eq 3389
description RDP to Server
object network Host_QA_Server
host 89.234.126.10
description QA Host External Address
object network Internal_Host_QA
host 192.168.20.22
description Host of VM machine for QA
object network Internal_QA_Web_Server
host 192.168.20.23
description Web Server in QA environment
object network Web_Server_QA_VM
host 89.234.126.11
description Web server in QA environment
object service SQL_Server
service tcp destination eq 1433
object network Demo_Server
host 89.234.126.12
description Server set up to Demo Product
object network Internal_Demo_Server
host 192.168.20.24
description Internal IP Address of Demo Server
object network NETWORK_OBJ_192.168.20.0_24
subnet 192.168.20.0 255.255.255.0
object network NETWORK_OBJ_192.168.50.0_26
subnet 192.168.50.0 255.255.255.192
object network NETWORK_OBJ_192.168.0.0_16
subnet 192.168.0.0 255.255.0.0
object service MSSQL
service tcp destination eq 1434
description MSSQL port
object network VPN-network
subnet 192.168.50.0 255.255.255.0
object network NETWORK_OBJ_192.168.50.0_24
subnet 192.168.50.0 255.255.255.0
object service TS
service tcp destination eq 4400
object service TS_Return
service tcp source eq 4400
object network External_QA_3
host 89.234.126.13
object network Internal_QA_3
host 192.168.20.25
object network Dev_WebServer
host 192.168.20.27
object network External_Dev_Web
host 89.234.126.14
object network NETWORK_OBJ_192.168.100.0_24
subnet 192.168.100.0 255.255.255.0
object network Wireless
subnet 192.168.40.0 255.255.255.0
description Wireless network
object network Servers
subnet 192.168.20.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq ftp
service-object tcp destination eq netbios-ssn
service-object tcp destination eq smtp
service-object object TS
service-object object SQL_Server
object-group service DM_INLINE_SERVICE_3
service-object tcp destination eq www
service-object tcp destination eq https
service-object object TS
service-object object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object object RDP
service-object tcp destination eq www
service-object tcp destination eq https
object-group service DM_INLINE_SERVICE_5
service-object object MSSQL
service-object object RDP
service-object object TS
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service DM_INLINE_SERVICE_6
service-object object TS
service-object object TS_Return
service-object tcp destination eq www
service-object tcp destination eq https
object-group network DM_INLINE_NETWORK_1
network-object 192.168.10.0 255.255.255.0
network-object 192.168.20.0 255.255.255.0
network-object 192.168.40.0 255.255.255.0
object-group network Payback_Internal
network-object 192.168.10.0 255.255.255.0
network-object 192.168.20.0 255.255.255.0
network-object 192.168.40.0 255.255.255.0
access-list outside_access_in remark This rule is allowing from internet to interal server.
access-list outside_access_in remark Allowed:
access-list outside_access_in remark FTP
access-list outside_access_in remark RDP
access-list outside_access_in remark SMTP
access-list outside_access_in remark Net Bios
access-list outside_access_in remark SQL
access-list outside_access_in remark TS - 4400
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any4 object Internal_Report_Server
access-list outside_access_in remark Access rule to internal host QA
access-list outside_access_in remark Allowed:
access-list outside_access_in remark HTTP
access-list outside_access_in remark RDP
access-list outside_access_in extended permit tcp any4 object Internal_Host_QA eq www
access-list outside_access_in remark Access to INternal Web Server:
access-list outside_access_in remark Allowed:
access-list outside_access_in remark HTTP
access-list outside_access_in remark RDP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 any4 object Internal_QA_Web_Server
access-list outside_access_in remark Rule for allowing access to Demo server
access-list outside_access_in remark Allowed:
access-list outside_access_in remark RDP
access-list outside_access_in remark MSSQL
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any4 object Internal_Demo_Server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
access-list outside_access_in remark Access for Development WebServer
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
access-list Payback_VPN_splitTunnelAcl standard permit 192.168.20.0 255.255.255.0
access-list outside_cryptomap extended permit ip object-group DM_INLINE_NETWORK_1 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging console informational
logging asdm informational
logging from-address [email protected]
logging recipient-address [email protected] level alerts
mtu outside 1500
mtu inside 1500
mtu servers 1500
mtu printers 1500
mtu wireless 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711-52.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
nat (wireless,outside) source static Wireless Wireless destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
nat (servers,outside) source static Servers Servers destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
nat (inside,outside) source dynamic any interface
nat (wireless,outside) source dynamic any interface
nat (servers,outside) source dynamic any interface
nat (servers,outside) source static Internal_Report_Server Report_Server
nat (servers,outside) source static Internal_Host_QA Host_QA_Server
nat (servers,outside) source static Internal_QA_Web_Server Web_Server_QA_VM
nat (servers,outside) source static Internal_Demo_Server Demo_Server
nat (servers,outside) source static NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 destination static NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 no-proxy-arp route-lookup
nat (servers,outside) source static Internal_QA_3 External_QA_3
nat (servers,outside) source static Dev_WebServer External_Dev_Web
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.10.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer XX.XX.XX.XX
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map servers_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map servers_map interface servers
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev2 enable inside client-services port 443
crypto ikev1 enable outside
crypto ikev1 enable inside
crypto ikev1 enable servers
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.10.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd dns 192.168.0.1
dhcpd auto_config outside
dhcpd address 192.168.10.21-192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
dhcpd option 15 ascii paybackloyalty.com interface inside
dhcpd enable inside
dhcpd address 192.168.40.21-192.168.40.240 wireless
dhcpd dns 192.168.20.21 83.147.160.2 interface wireless
dhcpd update dns interface wireless
dhcpd option 15 ascii paybackloyalty.com interface wireless
dhcpd enable wireless
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy Payback_VPN internal
group-policy Payback_VPN attributes
vpn-simultaneous-logins 10
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Payback_VPN_splitTunnelAcl
group-policy DfltGrpPolicy attributes
dns-server value 83.147.160.2 83.147.160.130
vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
group-policy GroupPolicy_84.39.233.50 internal
group-policy GroupPolicy_84.39.233.50 attributes
vpn-tunnel-protocol ikev1 ikev2
username Noelle password XB/IpvYaATP.2QYm encrypted
username Noelle attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Eanna password vXILR9ZZQIsd1Naw encrypted privilege 0
username Eanna attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Michael password qpbleUqUEchRrgQX encrypted
username Michael attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Danny password .7fEXdzESUk6S/cC encrypted privilege 0
username Danny attributes
vpn-group-policy Payback_VPN
service-type remote-access
username niamh password MlFlIlEiy8vismE0 encrypted
username niamh attributes
service-type admin
username Aileen password tytrelqvV5VRX2pz encrypted privilege 0
username Aileen attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Aidan password aDu6YH0V5XaxpEPg encrypted privilege 0
username Aidan attributes
vpn-group-policy Payback_VPN
service-type remote-access
username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
username shane.c password iqGMoWOnfO6YKXbw encrypted
username shane.c attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Shane password yQeVtvLLKqapoUje encrypted privilege 0
username Shane attributes
vpn-group-policy Payback_VPN
service-type remote-access
username James password TdYPv1pvld/hPM0d encrypted
username James attributes
vpn-group-policy Payback_VPN
service-type remote-access
username mark password yruxpddqfyNb.qFn encrypted
username mark attributes
service-type admin
username Mary password XND5FTEiyu1L1zFD encrypted
username Mary attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Massimo password vs65MMo4rM0l4rVu encrypted privilege 0
username Massimo attributes
vpn-group-policy Payback_VPN
service-type remote-access
tunnel-group Payback_VPN type remote-access
tunnel-group Payback_VPN general-attributes
address-pool VPN1
default-group-policy Payback_VPN
tunnel-group Payback_VPN ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 general-attributes
default-group-policy GroupPolicy_84.39.233.50
tunnel-group 84.39.233.50 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map global-class
match default-inspection-traffic
policy-map global-policy
class global-class
inspect dns
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect pptp
inspect rsh
inspect rtsp
inspect sip
inspect snmp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect xdmcp
inspect icmp error
inspect icmp
service-policy global-policy global
smtp-server 192.168.20.21
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:83fa7ce1d93375645205f6e79b526381
ASA2:
ASA Version 9.0(1)
hostname Payback-CIX
enable password HSMurh79NVmatjY0 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
description This port connects to VLAN 100
switchport access vlan 100
interface Ethernet0/2
interface Ethernet0/3
switchport access vlan 100
interface Ethernet0/4
switchport access vlan 100
interface Ethernet0/5
switchport access vlan 100
interface Ethernet0/6
switchport access vlan 100
interface Ethernet0/7
switchport access vlan 100
interface Vlan2
nameif outside
security-level 0
ip address X.X.X.X 255.255.255.240
interface Vlan100
nameif inside
security-level 100
ip address 192.168.100.1 255.255.255.0
banner login line Welcome to Payback Loyalty - CIX
ftp mode passive
clock timezone GMT 0
clock summer-time gmt/idt recurring last Sun Mar 1:00 last Sun Oct 2:00
dns domain-lookup outside
dns domain-lookup inside
dns server-group defaultDNS
name-server 8.8.8.8
name-server 8.8.4.4
same-security-traffic permit inter-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network CIX-Host-1
host 192.168.100.2
description This is the host machine of the VM servers
object network External_CIX-Host-1
host 84.39.233.51
description This is the external IP address of the host server for the VM server
object service RDP
service tcp source range 1 65535 destination eq 3389
object network Payback_Office
host 92.51.193.158
object service MSQL
service tcp destination eq 1433
object network Development_OLTP
host 192.168.100.10
description VM for Eiresoft
object network External_Development_OLTP
host 84.39.233.52
description This is the external IP address for the VM for Eiresoft
object network External_TMC_Web
host 84.39.233.53
description Public Address of TMC Webserver
object network TMC_Webserver
host 192.168.100.19
description Internal Address of TMC Webserver
object network External_TMC_OLTP
host 84.39.233.54
description Targets OLTP external IP
object network TMC_OLTP
host 192.168.100.18
description Targets interal IP address
object network External_OLTP_Failover
host 84.39.233.55
description Public IP of OLTP Failover
object network OLTP_Failover
host 192.168.100.60
description Server for OLTP failover
object network Servers
subnet 192.168.20.0 255.255.255.0
object network Wired
subnet 192.168.10.0 255.255.255.0
object network Wireless
subnet 192.168.40.0 255.255.255.0
object network NETWORK_OBJ_192.168.100.0_24
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.10.0_24
subnet 192.168.10.0 255.255.255.0
object network Eiresoft_2nd
host 137.117.217.29
description Eiresoft 2nd IP
object network Dev_Test_Webserver
host 192.168.100.12
description Dev Test Webserver Internal Address
object network External_Dev_Test_Webserver
host 84.39.233.56
description This is the PB Dev Test Webserver
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network LAN
subnet 192.168.100.0 255.255.255.0
object network REMOTE-LAN
subnet 192.168.10.0 255.255.255.0
object network TargetMC
host 83.71.194.145
description This is Target Location that will be accessing the Webserver
object network Rackspace_OLTP
host 162.13.34.56
description This is the IP address of production OLTP
object service DB
service tcp destination eq 5022
object network Topaz_Target_VM
host 82.198.151.168
description This is Topaz IP that will be accessing Targets VM
object service DB_2
service tcp destination eq 5023
object network EireSoft_NEW_IP
host 146.66.161.3
description Eiresoft latest IP form ISP DHCP
object-group service DM_INLINE_SERVICE_1
service-object object MSQL
service-object object RDP
service-object icmp echo
service-object icmp echo-reply
object-group service DM_INLINE_SERVICE_2
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_4
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
service-object tcp destination eq www
object-group service DM_INLINE_SERVICE_5
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_6
service-object object MSQL
service-object object RDP
object-group network Payback_Intrernal
network-object object Servers
network-object object Wired
network-object object Wireless
object-group service DM_INLINE_SERVICE_8
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_9
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_10
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
service-object icmp echo
service-object icmp echo-reply
service-object object DB
object-group service DM_INLINE_SERVICE_11
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_12
service-object object MSQL
service-object icmp echo
service-object icmp echo-reply
service-object object DB
service-object object DB_2
object-group service DM_INLINE_SERVICE_13
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_14
service-object object MSQL
service-object object RDP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-Host-1
access-list outside_access_in remark Development OLTP from Payback Office
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver
access-list outside_access_in remark Access to OLTP for target from Payback Office
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover
access-list outside_access_in remark Access for the 2nd IP from Eiresoft
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP
access-list outside_access_in remark Access from the 2nd Eiresoft IP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP
access-list outside_access_in remark Access rules from Traget to CIX for testing
access-list outside_access_in extended permit tcp object TargetMC object TMC_Webserver eq www
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_12 object Rackspace_OLTP object OLTP_Failover
access-list outside_access_in remark Topaz access to Target VM
access-list outside_access_in extended permit tcp object Topaz_Target_VM object TMC_Webserver eq www
access-list outside_access_in remark Opened up for Target for the weekend. Closing on Monday 20th
access-list outside_access_in extended permit tcp any object TMC_Webserver eq www
access-list outside_access_in remark Access for Eiresoft after their ISP changed their IP Address
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_13 object EireSoft_NEW_IP object Development_OLTP
access-list outside_access_in remark Eiresoft Access after ISP changed their IP Address
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_14 object EireSoft_NEW_IP object OLTP_Failover
access-list outside_cryptomap extended permit ip 192.168.100.0 255.255.255.0 object-group Payback_Intrernal
pager lines 24
logging enable
logging console debugging
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static Payback_Intrernal Payback_Intrernal no-proxy-arp route-lookup
nat (inside,outside) source static CIX-Host-1 External_CIX-Host-1
nat (inside,outside) source static Development_OLTP External_Development_OLTP
nat (inside,outside) source static TMC_Webserver External_TMC_Web
nat (inside,outside) source static TMC_OLTP External_TMC_OLTP
nat (inside,outside) source static OLTP_Failover External_OLTP_Failover
nat (inside,outside) source static Dev_Test_Webserver External_Dev_Test_Webserver
nat (inside,outside) source dynamic LAN interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http X.X.X.X 255.255.255.252 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer X.X.X.X
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh X.X.X.X 255.255.255.240 outside
ssh X.X.X.X 255.255.255.252 outside
ssh 192.168.40.0 255.255.255.0 outside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy GroupPolicy_92.51.193.158 internal
group-policy GroupPolicy_92.51.193.158 attributes
vpn-tunnel-protocol ikev1 ikev2
username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 general-attributes
default-group-policy GroupPolicy_92.51.193.158
tunnel-group 92.51.193.158 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:78a7b9ccec2fa048306092eb29a2b769 -
Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall
Hi,
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
3
Nov 21 2012
07:11:09
713061
Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5
Nov 21 2012
07:11:09
713119
Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
Here is from the syntax: show crypto isakmp sa
Result of the command: "show crypto isakmp sa"
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 195.149.180.254
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
current_peer:195.149.180.254
#pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
#pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: E715B315
inbound esp sas:
spi: 0xFAC769EB (4207372779)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38738/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xE715B315 (3876958997)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38673/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
And here are my Accesslists and vpn site to site config:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 84600
crypto isakmp nat-traversal 40
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map CustomerCryptoMap 10 match address VPN_Tunnel
crypto map CustomerCryptoMap 10 set pfs group5
crypto map CustomerCryptoMap 10 set peer 195.149.180.254
crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
crypto map CustomerCryptoMap interface outside
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
nat (inside) 0 access-list nonat
All these remote networks are at the Main Site Clavister Firewall.
Best Regards
MichaelHi,
I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
Maybe you could try to change the Encryption Domain configurations a bit and test it then.
You could also maybe take some debugs on the Phase2 and see if you get anymore hints as to what could be the problem when only one network is working for the L2L VPN.
- Jouni -
Cisco ASA 5505 Site to Site VPN Problem
Hi All,
We have a site to site VPN with a cisco asa 5505 on one end and a Checkpoint firewall on the other end.
We can establish the vpn tunnel and all users in the remote office are working great. However at a random point during the day or it may even be after 2 weeks of working, the tunnel between the sites automatically fails.
When I dial into the modem which is connected to the firewall I see the following messages in the logs:
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
There is nothing in the Checkpoint logs. To solve the issue I have to reload the firewall.
I have checked both firewalls for any mis-matched parameters and do not see any.
Any help is very much appreciated as it is very frustrating for myself and the users in the remote office.
Thanks!Also to note, PFS is enabled on both firewalls. Config on Cisco ASA firewall as follows:
hostname
domain-name
enable passwordpasswd names
interface Vlan701
nameif inside
security-level 100
ip address 10.65.0.69 255.255.255.252
interface Vlan999
nameif outside
security-level 0
ip address ****** 255.255.255.248
interface Ethernet0/0
description Link to Internet
switchport access vlan 999
interface Ethernet0/1
description
switchport access vlan 701
interface range Ethernet0/2 - 0/7
switchport access vlan 2
shutdown
ftp mode passive
dns server-group DefaultDNS
domain-name******
access-list 101 extended permit ip host ****** 172.25.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 host ******
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 ******* 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 ******** 255.255.255.0
pager lines 24
logging enable
logging timestamp
logging buffered warnings
logging trap warnings
logging asdm informational
logging host outside *****
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside) 0 access-list nonat
route inside ******
route outside 0.0.0.0 0.0.0.0 ********
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
snmp-server location **:
snmp-server contact **
snmp-server community shortkey
snmp-server enable traps snmp authentication linkup linkdown coldstart
snmp-server enable traps syslog
crypto ipsec transform-set 3desmd5 esp-3des esp-md5-hmac
crypto map CASGMAP 50 match address 101
crypto map CASGMAP 50 set pfs group1
crypto map CASGMAP 50 set peer ********
crypto map CASGMAP 50 set transform-set 3desmd5
crypto map CASGMAP 50 set security-association lifetime seconds 3600
crypto map CASGMAP interface outside
crypto isakmp enable outside
crypto isakmp policy 20
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet **** inside
telnet timeout 5
ssh **** inside
ssh **** outside
ssh timeout 5
console timeout 30
management-access inside
dhcpd ping_timeout 750
priority-queue outside
ntp server **
username ***
tunnel-group ******** type ipsec-l2l
tunnel-group ******** ipsec-attributes
pre-shared-key ***
class-map VoIP
match dscp ef
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map General-purpose
class VoIP
priority
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect http
service-policy General-purpose interface outside
prompt hostname context -
Cisco ASA 5505 Site to Site VPN tunnel up, but not passing traffic
Thanks to a previous thread, I do have a 5505 up and running, and passing data....
https://supportforums.cisco.com/message/3900751
Now I am trying to get a IPSEC VPN tunnel working.
I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
The networks concerned:
name 10.0.0.0 Eventual (HQ Site behind Firewall)
name 1.1.1.0 CFS (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)
name 2.2.2.0 T1 (Remote site - Outside interface of 5505: 2.2.2.2)
name 10.209.0.0 Local (Remote Network - internal interface of 5505: 10.209.0.3)
On a ping to the HQ network from behind the ASA, I get....
portmap translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work.
Below is the config.
Can anyone see if there is something sticking out?
: Saved
ASA Version 8.2(5)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.0 Eventual
name 10.209.0.0 Local
name 2.2.2.0 T1
name 1.1.1.0 CFS
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 10.209.0.3 255.0.0.0
interface Vlan2
nameif outside
security-level 0
ip address 2.2.2.2 255.255.255.248
time-range Indefinite
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
protocol-object udp
protocol-object tcp
object-group network DM_INLINE_NETWORK_1
network-object Eventual 255.0.0.0
network-object T1 255.255.255.248
network-object CFS 255.255.255.240
access-list outside_1_cryptomap extended permit ip Local 255.255.255.0 object-group DM_INLINE_NETWORK_1
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 67.139.113.217 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Eventual 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 1.1.1.1
crypto map outside_map 1 set transform-set ESP-3DES-MD5
crypto map outside_map 1 set phase1-mode aggressive
crypto map outside_map interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 10.209.0.201-10.209.0.232 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-policy FTMGP internal
group-policy FTMGP attributes
vpn-idle-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 general-attributes
default-group-policy FTMGP
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:701d8da28ee256692a1e49d904e9cb04
: end
asdm location Eventual 255.0.0.0 inside
asdm location Local 255.255.255.0 inside
asdm location T1 255.255.255.248 inside
asdm location CFS 255.255.255.240 inside
asdm history enable
Thank You.I'm just re-engaging on the firewall this afternoon, but right now I'm getting request timed out on the pings....
Here's the output requested:
Result of the command: "show crypto isakmp sa"
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 1.1.1.1
Type : L2L Role : initiator
Rekey : no State : AM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
Crypto map tag: outside_map, seq num: 1, local addr: 2.2.2.2
access-list outside_1_cryptomap extended permit ip 10.209.0.0 255.255.255.0 10.0.0.0 255.0.0.0
local ident (addr/mask/prot/port): (Local/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (Eventual/255.0.0.0/0/0)
current_peer: 1.1.1.1
#pkts encaps: 84, #pkts encrypt: 84, #pkts digest: 84
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 84, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 2.2.2.2, remote crypto endpt.: 1.1.1.1
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 8FC06BD1
current inbound spi : 42EC16F4
inbound esp sas:
spi: 0x42EC16F4 (1122768628)
transform: esp-3des esp-md5-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 4096, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (62207/28464)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
outbound esp sas:
spi: 0x8FC06BD1 (2411752401)
transform: esp-3des esp-md5-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 4096, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (62201/28464)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Here's the current config:
: Saved
ASA Version 8.2(5)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.0 Eventual
name 10.209.0.0 Local
name 67.139.113.216 T1
name 1.1.1.0 IntegraCFS
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 10.209.0.3 255.0.0.0
interface Vlan2
nameif outside
security-level 0
ip address 2.2.2.2 255.255.255.248
time-range Indefinite
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
protocol-object udp
protocol-object tcp
object-group network DM_INLINE_NETWORK_1
network-object Eventual 255.0.0.0
network-object T1 255.255.255.248
network-object IntegraCFS 255.255.255.240
access-list outside_1_cryptomap extended permit ip Local 255.255.255.0 object-group DM_INLINE_NETWORK_1
access-list No_NAT extended permit ip Local 255.255.255.0 Eventual 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list No_NAT
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 2.2.2.0 1
route outside Eventual 255.255.255.0 1.1.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Eventual 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 1.1.1.1
crypto map outside_map 1 set transform-set ESP-3DES-MD5
crypto map outside_map 1 set security-association lifetime kilobytes 65535
crypto map outside_map 1 set phase1-mode aggressive
crypto map outside_map interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 10.209.0.201-10.209.0.232 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-policy FTMGP internal
group-policy FTMGP attributes
vpn-idle-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 general-attributes
default-group-policy FTMGP
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:301e573544ce0f89b3c597bdfe2c414a
: end
asdm location Eventual 255.0.0.0 inside
asdm location Local 255.255.255.0 inside
asdm location T1 255.255.255.248 inside
asdm location IntegraCFS 255.255.255.240 inside
asdm history enable -
CIsco ASA 5505 and VPN licenses
Hi,
Cisco ASA 5505 comes with 10 VPN licenses in a standard configuration.
How those licenses are counted? Will I need a license per one IPSec SA?
If I have two site connected with LAN-to-LAN VPN with 10 subnets at one site, how many licenses will be taken? 10 - one per IPSec SA or just 1 - one per point-to-point VPN?
Thank you.
Regards,
AlexAlex,
In an ASA 5505, it should say something like this...when you do sh ver.
VPN Peers : 25
It means that you can have so many peers connecting to the ASA. Its not per IPSec SA.
Its a per tunnel license.
Rate this, if it helps!
Gilbert -
Cisco ASA 5505, Cisco VPN Client and Novell Netware
Hi,
Our ISP have installed Cisco ASA 5505 firewall. We are trying to connect to our Novell 5.1 server using VPN client.
I installed VPN client on a laptop that is using wireless connection. I connect using wireless signal from near by hotel and I am able to connect to my firewall usinging vpn client and also able to login in using Novell client for XP.
When I use same vpn client and Novell client at home that is not using wireless connection, but DSL connection amd not able to login or find the tree.
The only difference in two machine is laptop using wireless connection and my home machine is using wired connection using DSL.If your remote end of the services in question support IPsec IKEv1 as the VPN type then, yes - the 5505 can be a client for that service. At that point it looks like a regular LAN-LAN VPN which is documented in many Cisco and 3rd party how-to documents.
-
Setting up site to site vpn with cisco asa 5505
I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
IP of remote office router is 71.37.178.142
IP of the main office firewall is 209.117.141.82
Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
ciscoasa# show run
: Saved
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password TMACBloMlcBsq1kp encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group5
crypto map outside_map 1 set peer 209.117.141.82
crypto map outside_map 1 set transform-set ESP-AES-256-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn username [email protected] password ********* store-local
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.129 inside
dhcpd enable inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
: end
ciscoasa#
Thanks!Hi Mandy,
By using following access list define Peer IP as source and destination
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
you are not defining the interesting traffic / subnets from both ends.
Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
!.1..source subnet(called local encryption domain) at your end 192.168.200.0
!..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
!..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
!...at your end 192.168.200.0
!..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
!...at other end 192.168.100.0
Please use Baisc Steps as follows:
A. Configuration in your MAIN office having IP = 209.117.141.82 (follow step 1 to 6)
Step 1.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
Step 2.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256 --->2nd parameter of ISAKMP Policy is OK
hash sha ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 3.
Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 71.37.178.142
or , but not both
crypto isakmp key 6 CISCO123 address71.37.178.142
step 4.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 5.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 6.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Configure the same but just change ACL on other end in step one by reversing source and destination
and also set the peer IP of this router in other end.
So other side config should look as follows:
B. Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
Step 7.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
Step 8.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256 --->2nd parameter of ISAKMP Policy is OK
hash sha ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 9.
Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 209.117.141.82
or , but not both
crypto isakmp key 6 CISCO123 address 209.117.141.82
step 10.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 11.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set, only one is permissible
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 12.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Now initite a ping
Here is for your summary:
IPSec: Site to Site - Routers
Configuration Steps
Phase 1
Step 1: Configure Mirrored ACL/Crypto ACL for Interesting Traffic
Step 2: Configure ISAKMP Policy
Step 3: Configure ISAKMP Key
Phase 2
Step 4: Configure Transform Set
Step 5: Configure Crypto Map
Step 6: Apply Crypto Map to an Interface
To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
Router#debug crpyto isakmp
Router#debug crpyto ipsec
Router(config)# logging buffer 7
Router(config)# logging buffer 99999
Router(config)# logging console 6
Router# clear logging
Configuration
In R1:
(config)# access-list 101 permit ipo host 10.1.1.1 host 10.1.2.1
(config)# crypto isakmp policy 10
(config-policy)# encryption 3des
(config-policy)# authentication pre-share
(config-policy)# group 2
(config-policy)# hash sha1
(config)# crypto isakmp key 0 cisco address 2.2.2.1
(config)# crypto ipsec transform-set TSET esp-3des sha-aes-hmac
(config)# crypto map CMAP 10 ipsec-isakmp
(config-crypto-map)# set peer 2.2.2.1
(config-crypto-map)# match address 101
(config-crypto-map)# set transform-set TSET
(config)# int f0/0
(config-if)# crypto map CMAP
Similarly in R2
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Change to Transport Mode, add the following command in Step 4:
(config-tranform-set)# mode transport
Even after doing this change, the ipsec negotiation will still be done through tunnel mode if pinged from Loopback to Loopback. To overcome this we make changes to ACL.
Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
(config)# crypto isakmp peer address 2.2.2.1
(config-peer)# set aggressive-mode password cisco
(config-peer)# set aggressive-mode clien-endpoint ipv4-address 2.2.2.1
Similarly on R2.
The below process is for the negotiation using RSA-SIG (PKI) as authentication type
Debug Process:
After we debug, we can see the negotiation between the two peers. The first packet of the interesting traffic triggers the ISAKMP (Phase1) negotiation. Important messages are marked in BOLD and explanation in RED
R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 2.2.2.2
Mar 2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) // Router tried to find any IPSec SA matching the outgoing connection but no valid SA has been found in Security Association Database (SADB)
Mar 2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
Mar 2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
Mar 2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
Mar 2 16:18:42.939: ISAKMP: local port 500, remote port 500
Mar 2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE
Mar 2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
Mar 2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
Mar 2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
Mar 2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Mar 2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY New State = IKE_I_MM1
Mar 2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
Mar 2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1 New State = IKE_I_MM2
Mar 2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947:.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
R2(config)# ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
Mar 2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
Mar 2 16:18:42.947: ISAKMP: encryption 3DES-CBC
Mar 2 16:18:42.947: ISAKMP: hash SHA
Mar 2 16:18:42.947: ISAKMP: default group 2
Mar 2 16:18:42.947: ISAKMP: auth RSA sig
Mar 2 16:18:42.947: ISAKMP: life type in seconds
Mar 2 16:18:42.947: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
Mar 2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
Mar 2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
Mar 2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM2
Mar 2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
Mar 2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM3
Mar 2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
Mar 2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3 New State = IKE_I_MM4
Mar 2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
Mar 2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:43.007: Choosing trustpoint CA_Server as issuer
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
Mar 2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM4
Mar 2 16:18:43.011: ISAKMP:(1008):Send initial contact
Mar 2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
Mar 2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
Mar 2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
Mar 2 16:18:43.011: ISAKMP (1008): ID payload
next-payload : 6
type : 2
FQDN name : R2
protocol : 17
port : 500
length : 10
Mar 2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
Mar 2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
Mar 2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
Mar 2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Mar 2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM5
Mar 2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
// "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
Mar 2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP (1008): ID payload
next-payload : 6
type : 2
FQDN name : ASA1
protocol : 0
port : 0
length : 12
Mar 2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
Mar 2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
Mar 2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
Mar 2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
Mar 2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
Mar 2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
Mar 2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
Mar 2 16:18:43.067: ISAKMP:received payload type 17
Mar 2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
Mar 2 16:18:43.067: ISAKMP:(1008):SA authentication status:
authenticated
Mar 2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
Mar 2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/, and inserted successfully 46519678. // SA inserted into SADB
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5 New State = IKE_I_MM6
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_I_MM6
Mar 2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_P1_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
Mar 2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
Mar 2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY New State = IKE_QM_I_QM1
Mar 2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
Mar 2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
Mar 2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
Mar 2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
Mar 2 16:18:43.079: ISAKMP: attributes in transform:
Mar 2 16:18:43.079: ISAKMP: SA life type in seconds
Mar 2 16:18:43.079: ISAKMP: SA life duration (basic) of 3600
Mar 2 16:18:43.079: ISAKMP: SA life type in kilobytes
Mar 2 16:18:43.079: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
Mar 2 16:18:43.079: ISAKMP: encaps is 1 (Tunnel)
Mar 2 16:18:43.079: ISAKMP: authenticator is HMAC-SHA
Mar 2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
Mar 2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
Mar 2 16:18:43.083: inbound SA from 20.1.1.10 to 40.1.1.1 (f/i) 0/ 0
(proxy 1.1.1.1 to 2.2.2.2)
Mar 2 16:18:43.083: has spi 0xA9A66D46 and conn_id 0
Mar 2 16:18:43.083: lifetime of 3600 seconds
Mar 2 16:18:43.083: lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
(proxy 2.2.2.2 to 1.1.1.1)
Mar 2 16:18:43.083: has spi 0x2B367FB4 and conn_id 0
Mar 2 16:18:43.083: lifetime of 3600 seconds
Mar 2 16:18:43.083: lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
Mar 2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
Mar 2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1 New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Kindly rate if you find the explanation useful !!
Best Regards
Sachin Garg -
Cisco ASA 5505 VPN Routing/Networking Question
I have a very basic question about Cisco ASA 5505 IPsec Site to Site VPNs. I want to install a Cisco ASA 5505 at a Data Center, in a LAN subnet that utilizes publicly routable IP addresses. I would like to install a second Cisco ASA 5505 in a remote branch office as its peer.
Regardless of whether I use publicly routable IPs at the branch office in the "inside" network or non-routable IPs, how would the devices and servers at the Data Center know to route IP packets destined for the branch office back through the Cisco ASA instead of through the default gateway at the Data Center? I can see accomplishing this if every single device at the Data Center is configured with routing table entries, but that isn't feasible. It also isn't feasible to use the Cisco ASA 5505 as the default gateway for all of the devices as the Data Center, allowing it to decide where the traffic should go.
What am I missing? Is the solution to try to map branch office IPs to IP addresses within the Data Center's LAN subnet so that all of the traffic is on the same subnet?You can do it in several different ways.
One way is to tell the server that if it has traffic to network x then it needs to go to the ASA all other traffic is to head for the default gateway.
In windows this is done via the route command
do not forget to make it "persistent" otherwise the route will disapear when your reboot the server.
in unix/linux
It is also the route command
Or you can tell your "default gateway" to route that network to the ASA
Good luck
HTH -
Hi Everyone,
In my study home lab, I wanted to configure a cisco ASA 5505 ( Base license) to allow SSL VPN. I follow carefully the configuration procedure as instructed on a short videos I downloaded on youtube.
I configured my outside e0/0 with a valid static IP address, unfortunately the vpn connection is timeout on a remote ( different) internet connection. But if I connect to my own internet line using a WIFI the VPN ( AnyConnect SSL VPN client ) connection is established.
I need help to solve this mystery. Please find attached the ASA config: #show run
I hope my explaination does make sense, if not accept my apology I am just new in cisco technology.
Best regards,
BENIf you can connect with your own internet line, then most probably it's not an issue with the ASA configuration.
I would check how you are routing the ASA to the internet, and if there is any ACL that might be blocking inbound access to the ASA on the device in front of the ASA. -
Hello all thanks for looking,
I need to know how to setup my cisco asa 5505 as a vpn client to services like HMA or privateinternet and other paid VPN services. If someone else has already written a guide to this then that would be great. What I want to do is route all my secure traffice through the asa and have it go across the internet as encrypted VPN stuff and have my other stuff that does not need to be encrypted just go through to my other router.
Thanks in advance,If your remote end of the services in question support IPsec IKEv1 as the VPN type then, yes - the 5505 can be a client for that service. At that point it looks like a regular LAN-LAN VPN which is documented in many Cisco and 3rd party how-to documents.
-
I have a cisco asa 5505 that I am setting up VPN access too. I have multiple subnets all routed through a layer 3 switch conected to my asa. My problem is I can ping everything on VLAN1 (192.168.100.0/24) but no other VLANS (10.141.152.0/23 etc.)
Post the config of your ASA and someone will be able to assist.
-
Cisco Asa 5505 and Layer 3 Switch With Remote VPN Access
i got today a new CISCO LAYER 3 Switch .. so here is my scenrio
Cisco Asa 5505
I
Outside == 155.155.155.x
Inside = 192.168.7.1
VPN POOL Address = 10.10.10.1 - 10.10.10.20
Layer 3 Switch Config
Vlan 2
interface ip address = 192.168.1.1
Vlan 2
interface ip address = 192.168.2.1
Vlan 2
interface ip address = 192.168.3.1
Vlan 2
interface ip address = 192.168.4.1
Vlan 2
interface ip address = 192.168.5.1
ip Routing
So i want My Remote Access VPN clients to access all this Networks. So Please can you give me a helpfull trick or Link to configure the rest of my routing
Thank You allWhen My Remote VPN is Connected , it reaches 192.168.7.2 of the Layer 3 VLan that's Connected to The ASA 5505 ,
But i can't reach the rest of the VLAN - example
192.168.1.1
192.168.1.2
192.168.1.3
192.168.1.4
192.168.1.5
But i can reach the Connected Interface Vlan to My ASA ..
So here i think iam miss configuration to my Route
Any Help Please this is urgent -
Cisco VPN 3002 to Cisco ASA 5505
I want to remove a Cisco VPN 3002 Hardware client and replace it with a Cisco ASA 5505. Is there a way to do this? I want to have the remote user and group authentication and no split tunneling.?
Thanks for your help.Sure can.
Here is a sample configuration for ASA5505 acting as a remote hardware easy vpn client (like the VPN3002):
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00808a61f4.shtml
If you don't want split tunneling, then I assume that it is in PAT/client mode instead of NEM mode as above sample configuration.
You can just change the "vpnclient mode network-extension-mode" to "vpnclient mode client-mode"
Hope this helps. -
VPN Site to Site Cisco ASA-5505-BUN-50 to RV-042
Hello guys , anyone has an example for connect by VPN Site to Site a Cisco ASA-5505 with RV-042 , i need establish a link for connect my UC560 with CUE on Cisco Router 2800 for VoIP Site to Site calls.
ThanksOn ASA running 8.4.3. B side. I believe object "email" is defined incorrectly.
Existing configuration
object network email
host 172.16.0.0
description 255.255.0.0
Correct configuration
object network email
subnet 172.16.0.0 255.255.0.0
Maybe you are looking for
-
Why isn't iWeb uploading my changes?
For some reason iWeb is not updating my changes I make to my pages, especially my blog. I check to make sure the connection is good and it still will not upload. I save changes and then try to get out of iWeb and I get the error message that says qui
-
Server Admin- Mail queue is this before or after its been checked as spam?
Hi we have been bombarded with shed loads of junk causing the mail queue to swell and slow down considerably almost to a halt. I have now created the junkmail account and the notjunkmail accounts and now trying to teach the server to sort itself out.
-
I hope that the added/purchased iCloud memory applies to all my apple products
-
Communication between Appliation Server and Database Server
If a web app is deployed to an Oracle Application Server, this AS machine is physically connected to an Oracle Database (server) machine in the same location: For the purpose of sending and retrieving data from AS server to/from DB server, do I need
-
Sql 2008 peer-to-peer replication and jdbc driver
Hi, sorry but i'm a sql dummy...:-) I setup a sql 2008 p2p replication for a database. Can i specify, on a jbdc connection string, the path of the 2nd sql server for automatic failover? I try failoverPartner variable, but this is only for database mi