Cisco ASA 5505 Remote Access IP/Sec VPN Connectivity Issues

We have a Cisco ASA that we use just for Remote Access VPN. It uses UDP and was working fine for about 2 months. Recently clients have had intermittent issues when connecting from home. The following message is display by the Cisco VPN Client :
"Secure VPN connection terminated locally by the Client. Reason 412: The remote peer is no longer responding"
Upon looking at a client side packet capture, I notice that no response is being given back to the client for the udp packets sent to the ASA on udp 500. If I login to the ASA from the LAN and send a single ping FROM the ASA, then the client can connect without issue. I don't understand the significance of the needed outbound ping since ping is not used by the client to test if the ASA is alive.
Once again this is a remote access udp ip/sec VPN. I set most of it up with the VPN wizard and then backed up the config. The issue started happening at least a month after setup (maybe two) and I restored to the saved config just in-case, but the issue remains.
Any insight would be greatly appreciated.
I'm using IOS 831 and have tried 821 and 823 as one thread that I found recommended downgraded to 821.
Thanks much,
Justin

Javier,
I logged into the ASA last time the VPN went down. I issued the following commands:
debug crypto isakmp 190
debug crypto ipsec 190
capture outside-cap interface outside match udp any any
I then used a remote access tool to access the client and tried to connect. I got absolutely nothing from debugging. So I issued the following command:
show capture outside | include 500
and also got nothing. So I issued the following command:
ping 4.2.2.2
Upon which my normal deug messaged began to showup, so I issued the show capture outside command again and recieved the expected output below:
   1: 15:44:18.570160 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 868
   2: 15:44:18.579269 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 444
   3: 15:44:18.703866 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 172
   4: 15:44:18.706567 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 76
   5: 15:44:18.831499 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 92
   6: 15:44:19.024061 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 76
   7: 15:44:19.111963 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 60
   8: 15:44:19.517185 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 204
   9: 15:44:19.521350 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 92
  10: 15:44:19.522723 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 252
  11: 15:44:42.121957 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 868
  12: 15:44:42.130822 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 444
  13: 15:44:42.228397 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 172
  14: 15:44:42.231036 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 76
  15: 15:44:42.329557 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 92
  16: 15:44:42.521091 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 76
  17: 15:44:42.610167 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 60
  18: 15:44:42.649258 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 204
  19: 15:44:42.653790 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 252
  20: 15:44:42.789342 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 1036
  21: 15:44:42.792119 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 92
  22: 15:44:42.800846 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 188
  23: 15:44:42.892120 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 60
  34: 15:44:54.446220 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 92
  35: 15:44:54.447913 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 92
  70: 15:45:01.825000 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000:  udp 100
174: 15:45:03.417764 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000:  udp 500
377: 15:45:07.881500 802.1Q vlan#2 P0 REMOTE_IP.10000 > OFFICE_IP.10000:  udp 100    1: 15:44:18.570160 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 868
   2: 15:44:18.579269 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 444
   3: 15:44:18.703866 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 172
   4: 15:44:18.706567 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 76
   5: 15:44:18.831499 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 92
   6: 15:44:19.024061 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 76
   7: 15:44:19.111963 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 60
   8: 15:44:19.517185 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 204
   9: 15:44:19.521350 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 92
  10: 15:44:19.522723 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 252
  11: 15:44:42.121957 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 868
  12: 15:44:42.130822 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 444
  13: 15:44:42.228397 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 172
  14: 15:44:42.231036 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 76
  15: 15:44:42.329557 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 92
  16: 15:44:42.521091 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 76
  17: 15:44:42.610167 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 60
  18: 15:44:42.649258 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 204
  19: 15:44:42.653790 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 252
  20: 15:44:42.789342 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 1036
  21: 15:44:42.792119 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 92
  22: 15:44:42.800846 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 188
  23: 15:44:42.892120 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 60
  34: 15:44:54.446220 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 92
  35: 15:44:54.447913 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 92
  70: 15:45:01.825000 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000:  udp 100
174: 15:45:03.417764 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000:  udp 500
377: 15:45:07.881500 802.1Q vlan#2 P0 REMOTE_IP.10000 > OFFICE_IP.10000:  udp 100
It would seem as if no traffic reached the ASA until some outbound traffic to an arbitrary public IP. In this case I sent an echo request to a public DNS server. It seems almost like a state-table issue although I don't know how ICMP ties in.
Once again, any insight would be greatly appreciated.
Thanks,
Justin

Similar Messages

  • Cisco ASA 5505 site to site IPSec VPN with RV220W issue

    I have a ASA5505 connected to RV220W through IPSec VPN. When  using SMB to transfer large file, the ASA5505 will show error message:
    CTM ERROR: Invalid input parameters, ctm_get_scb_prot_stats:1561
    The error message from the debug crypto engine. When  the message show, the speed of the transfer will slow down quickly, and  even no data can be go through between ASA and the RV220W. But the IPSec  SA and the IKE SA is active, and can ping the inside network in both  site.
    Both ASA5505 and the RV220W has been updated the latest firmware. I have surf the Google but no such related issue found.
    Any suggestions on where to look would be much appreciated.
    Thanks in advance
    Terry

    Hi Ted thanks for your reply and information.
    The strange things happened in RV220W shows the IPSec sa is expired, but the ASA5505 IPSec and IKEv1 sa is active. Inside both site internal network can ping to other side, but cant transfer file through Windows SMB. It seems when I transfer over 4GBytes of file, it will start happening and required clear IPSec and IKEv1 sa so that the VPN tunnel will start up again.
    I am already surrander for this issue......

  • Cisco ASA 5505 VPN Routing/Networking Question

    I have a very basic question about Cisco ASA 5505 IPsec Site to Site VPNs.  I want to install a Cisco ASA 5505 at a Data Center, in a LAN subnet that utilizes publicly routable IP addresses.  I would like to install a second Cisco ASA 5505 in a remote branch office as its peer. 
    Regardless of whether I use publicly routable IPs at the branch office in the "inside" network or non-routable IPs, how would the devices and servers at the Data Center know to route IP packets destined for the branch office back through the Cisco ASA instead of through the default gateway at the Data Center?  I can see accomplishing this if every single device at the Data Center is configured with routing table entries, but that isn't feasible.  It also isn't feasible to use the Cisco ASA 5505 as the default gateway for all of the devices as the Data Center, allowing it to decide where the traffic should go.
    What am I missing?  Is the solution to try to map branch office IPs to IP addresses within the Data Center's LAN subnet so that all of the traffic is on the same subnet?

    You can do it in several different ways.
    One way is to tell the server that if it has traffic to network x then it needs to go to the ASA all other traffic is to head for the default gateway.
    In windows this is done via the route command
    do not forget to make it "persistent" otherwise the route will disapear when your reboot the server.
    in unix/linux
    It is also the route command
    Or you can tell your "default gateway" to route that network to the ASA
    Good luck
    HTH

  • Cisco ASA 5505/Cisco 3750

    I have a Cisco 5505(base license) and a Cisco 3750(48 port). I want to be able to connect to the 3750 on different vlans(for home lab),but I'm no able to ping the "outside" IP of the ASA. I can ping the different vlans from the ASA once I created the routes from the ASA.
    3750 config:
    version 12.2
    no service pad
    service timestamps debug uptime
    service timestamps log uptime
    no service password-encryption
    hostname SwitchA
    no aaa new-model
    switch 1 provision ws-c3750-48p
    ip subnet-zero
    ip routing
    no file verify auto
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet1/0/1
    description Uplink to Cisco ASA 5505
    switchport access vlan 100
    switchport mode access
    spanning-tree portfast
    interface FastEthernet1/0/2
    no switchport
    no ip address
    interface FastEthernet1/0/3
    interface FastEthernet1/0/4
    interface FastEthernet1/0/5
    switchport access vlan 10
    interface FastEthernet1/0/6
    interface Vlan1
    no ip address
    interface Vlan2
    ip address 10.10.0.1 255.255.255.0
    interface Vlan3
    ip address 10.10.1.254 255.255.255.0
    interface Vlan10
    no ip address
    interface Vlan100
    description SW-to-ASA
    ip address 172.16.100.2 255.255.255.0
    interface Vlan172
    no ip address
    interface Vlan182
    no ip address
    interface Vlan192
    no ip address
    ip classless
    ip route 0.0.0.0 0.0.0.0 172.16.100.1
    ip http server
    ip http secure-server
    ASA Config:
    interface Vlan1
    shutdown
    no nameif
    no security-level
    no ip address
    interface Vlan10
    nameif users
    security-level 100
    ip address 172.16.10.254 255.255.255.0
    interface Vlan172
    no nameif
    security-level 100
    ip address 172.16.100.1 255.255.255.0
    interface Vlan192
    nameif OUTSIDE
    security-level 0
    ip address 192.168.1.1 255.255.255.0
    interface Ethernet0/0
    switchport access vlan 192
    interface Ethernet0/1
    description Trunk to Switch
    switchport access vlan 172
    Is this even doable?

    Hi,
    I believe you have the problem with your no-nat configurations..... you to exempt NAT for the traffic from 172.16.10.0 (Anyconnect VPN pool) to 192.168.1.0/24 (Inside LAN) to make this work
    object network acvpnpool
    subnet <anyconnect VPN Subnet>
    object network insidelan
    subnet <inside lan subnet>
    nat (inside,outside) source static acvpnpool acvpnpool destination static insidelan insidelan
    Make sure that you are able to reach the GW/Inside ip adress of the firewall from LAN machine.... all routing in place properly..... Thanks!!!
    Regards
    Karthik

  • Cisco Asa 5505 and Layer 3 Switch With Remote VPN Access

    i got today a new CISCO LAYER 3 Switch .. so here is my scenrio
    Cisco Asa 5505
    I
    Outside  == 155.155.155.x
    Inside  =      192.168.7.1
    VPN POOL Address =   10.10.10.1   -   10.10.10.20
    Layer 3 Switch Config
    Vlan 2
    interface ip address =  192.168.1.1
    Vlan 2
    interface ip address =  192.168.2.1
    Vlan 2
    interface ip address =  192.168.3.1
    Vlan 2
    interface ip address =  192.168.4.1
    Vlan 2
    interface ip address =  192.168.5.1
    ip Routing
    So i want My Remote Access VPN clients to access all this Networks. So Please can you give me a helpfull trick or Link to configure the rest of my routing
    Thank You all

    When My Remote VPN is Connected , it reaches 192.168.7.2 of the Layer 3 VLan that's Connected to The ASA 5505 ,
    But i can't reach the rest of the VLAN - example
    192.168.1.1
    192.168.1.2
    192.168.1.3
    192.168.1.4
    192.168.1.5
    But i can reach the Connected Interface Vlan to My ASA ..
    So here i think iam miss configuration to my Route
    Any Help Please this is urgent

  • Asa 5505 Remote VPN Can't access with my local network

    Hello Guys ,, i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration , please can you help me
    ASA Version 8.2(1)
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.30.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 155.155.155.10 255.255.255.0
    interface Vlan5
    no nameif
    no security-level
    no ip address
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    access-list inside_nat0_outbound extended permit ip any 192.168.100.0 255.255.255.240
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool vpn-Pool 192.168.100.1-192.168.100.10 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy mull internal
    group-policy mull attributes
    vpn-tunnel-protocol IPSec
    username xxx password eKJj9owsQwAIk6Cw encrypted privilege 0
    vpn-group-policy Mull
    tunnel-group mull type remote-access
    tunnel-group mull general-attributes
    address-pool vpn-Pool
    default-group-policy mull
    tunnel-group mull ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny 
      inspect sunrpc
      inspect xdmcp
      inspect sip 
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context

    Hey Jennifer i did every thing you mention it , but still i can't reach my inside network (LOCAL network)  iam using Shrew Soft VPN Access Manager for my vpn connection
    here is my cry ipsec sa
    interface: outside
        Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: 155.155.155.1
          local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.100.1/255.255.255.255/0/0)
          current_peer:155.155.155.1, username: Thomas
          dynamic allocated peer ip: 192.168.100.1
          #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
          #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
          #pkts compressed: 0, #pkts decompressed: 0
          #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
          #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
          #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
          #send errors: 0, #recv errors: 0
          local crypto endpt.: 155.155.155.1/4500, remote crypto endpt.: 155.155.155.20/4500
          path mtu 1500, ipsec overhead 82, media mtu 1500
          current outbound spi: 73FFAB96
        inbound esp sas:
          spi: 0x1B5FFBF1 (459275249)
             transform: esp-aes esp-sha-hmac no compression
             in use settings ={RA, Tunnel,  NAT-T-Encaps, }
             slot: 0, conn_id: 12288, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
             sa timing: remaining key lifetime (sec): 2894
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001
        outbound esp sas:
          spi: 0x73FFAB96 (1946135446)
             transform: esp-aes esp-sha-hmac no compression
             in use settings ={RA, Tunnel,  NAT-T-Encaps, }
             slot: 0, conn_id: 12288, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
             sa timing: remaining key lifetime (sec): 2873
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001

  • I need helping!!! configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.

    I need helping configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.
    I have attempted to configure rdp access but it does not seem to be working for me Could I please ask someone to help me modify my current configuration to allow this? Please do step by step as I could use all the help I could get.
    I need to allow the following IP addresses to have RDP access to my server:
    66.237.238.193-66.237.238.222
    69.195.249.177-69.195.249.190
    69.65.80.240-69.65.80.249
    My external WAN server info is - 99.89.69.333
    The internal IP address of my server is - 192.168.6.2
    The other server shows up as 99.89.69.334 but is working fine.
    I already added one server for Static route and RDP but when I try to put in same commands it doesnt allow me to for this new one. Please take a look at my configuration file and give me the commands i need in order to put this through. Also please tell me if there are any bad/conflicting entries.
    THE FOLLOWING IS MY CONFIGURATION FILE
    Also I have modified IP information so that its not the ACTUAL ip info for my server/network etc... lol for security reasons of course
    Also the bolded lines are the modifications I made but that arent working.
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password DowJbZ7jrm5Nkm5B encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.6.254 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 99.89.69.233 255.255.255.248
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    object-group network EMRMC
    network-object 10.1.2.0 255.255.255.0
    network-object 192.168.10.0 255.255.255.0
    network-object 192.168.11.0 255.255.255.0
    network-object 172.16.0.0 255.255.0.0
    network-object 192.168.9.0 255.255.255.0
    object-group service RDP tcp
    description RDP
    port-object eq 3389
    object-group service GMED tcp
    description GMED
    port-object eq 3390
    object-group service MarsAccess tcp
    description MarsAccess
    port-object range pcanywhere-data 5632
    object-group service MarsFTP tcp
    description MarsFTP
    port-object range ftp-data ftp
    object-group service MarsSupportAppls tcp
    description MarsSupportAppls
    port-object eq 1972
    object-group service MarsUpdatePort tcp
    description MarsUpdatePort
    port-object eq 7835
    object-group service NM1503 tcp
    description NM1503
    port-object eq 1503
    object-group service NM1720 tcp
    description NM1720
    port-object eq h323
    object-group service NM1731 tcp
    description NM1731
    port-object eq 1731
    object-group service NM389 tcp
    description NM389
    port-object eq ldap
    object-group service NM522 tcp
    description NM522
    port-object eq 522
    object-group service SSL tcp
    description SSL
    port-object eq https
    object-group service rdp tcp
    port-object eq 3389
    access-list outside_1_cryptomap extended permit ip 192.168.6.0 255.255.255.0 object-group EMRMC
    access-list inside_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 192.168.0.0 255.255.0.0
    access-list inside_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 object-group EMRMC
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 eq pcanywhere-data
    access-list outside_access_in extended permit udp 69.16.158.128 255.255.255.128 host 99.89.69.334 eq pcanywhere-status
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 object-group RDP
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq ftp
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq ldap
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq h323
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq telnet
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq www
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 object-group SSL
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 object-group NM522
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 object-group NM1731
    access-list outside_access_in extended permit tcp 173.197.144.48 255.255.255.248 host 99.89.69.334 object-group RDP
    access-list outside_access_in extended permit tcp any interface outside eq 3389
    access-list outside_access_in extended permit tcp host 66.237.238.194 host 99.89.69.333
    access-list outside_access_in extended permit tcp host 66.237.238.194 host 99.89.69.333 object-group rdp
    access-list outside_access_in extended permit tcp any host 99.89.69.333 object-group rdp
    access-list out_in extended permit tcp any host 192.168.6.2 eq 3389
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    static (inside,outside) tcp 99.89.69.334 3389 192.168.6.1 3389 netmask 255.255.255.255
    static (inside,outside) tcp interface 3389 192.168.6.2 3389 netmask 255.255.255.255
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 99.89.69.338 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.6.0 255.255.255.0 inside
    http 0.0.0.0 0.0.0.0 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set peer 68.156.148.5
    crypto map outside_map 1 set transform-set ESP-3DES-MD5
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash md5
    group 1
    lifetime 86400
    crypto isakmp policy 30
    authentication pre-share
    encryption 3des
    hash md5
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    tunnel-group 68.156.148.5 type ipsec-l2l
    tunnel-group 68.156.148.5 ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:f47dfb2cf91833f0366ff572eafefb1d
    : end
    ciscoasa(config-network)#

    Unclear what did not work.  In your original post you include said some commands were added but don't work:
    static (inside,outside) tcp interface 3389 192.168.6.2 3389 netmask 255.255.255.255
    and later you state you add another command that gets an error:
    static (inside,outside) tcp 99.89.69.333 3389 192.168.6.2 3389 netmask 255.255.255.255
    You also stated that 99.89.69.333 (actually 99.89.69.233, guessing from the rest of your config and other posts) is your WAN IP address.
    The first static statement matches Cisco's documentation, which states that a static statement must use the 'interface' directive when you are trying to do static PAT utilizing the IP address of the interface.  Since 99.89.69.333 is the assigned IP address of your WAN interface, that may explain why the second statement fails.
    Any reason why you are using static PAT (including the port number 3389) instead of just skipping that directive?  Static PAT usually makes sense when you need to change the TCP port number.  In your example, you are not changing the TCP port 3389.

  • Unable to access/lan2lan ping from VPN Fortigate to Cisco ASA 5505

    Problem : Unable to access user A to user B
    User A --- router A (122, fortigate 80c) --- (Site to Site VPN between fortigate & cisco asa) --- router B (93, cisco Asa 5505{in front asa got cisco800[81] before to internet} )  --- User B
    After using wizard to configure the cisco ASA site to site VPN, the site-to-site tunnel is up.
    Ping is unsuccessful from user A to user B
    Ping is successful from user B to user A, data is accessable
    After done the packet tracer from user A to user B,
    Result :
    Flow-lookup
    Action : allow
    Info: Found no matching flow, creating a new flow
    Route-lookup
    Action : allow
    Info : 192.168.5.203 255.255.255.255 identity
    Access-list
    Action : drop
    Config Implicit Rule
    Result - The packet is dropped
    Input Interface : inside
    Output Interface : NP Identify Ifc
    Info: (acl-drop)flow is denied by configured rule
    Below is Cisco ASA 5505's show running-config
    ASA Version 8.2(1)
    hostname Asite
    domain-name ssms1.com
    enable password ZZZZ encrypted
    passwd WWWW encrypted
    names
    name 82 B-firewall description Singapore office firewall
    name 192.168.1.0 B-inside-subnet description Singapore office internal LAN IP
    name 192.168.200.0 A-inside-VLAN12 description A-inside-VLAN12 (fortinet)
    name 192.168.2.0 fw-inside-subnet description A office internal LAN IP
    name 122 A-forti
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.5.203 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 93 255.255.255.240
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name ssms1.com
    object-group network obj_any
    network-object 0.0.0.0 0.0.0.0
    access-list inside_nat0_outbound extended permit ip any 80 255.255.255.240
    access-list inside_nat0_outbound extended permit ip fw-inside-subnet 255.255.255.0 B-inside-subnet 255.255.255.0
    access-list inside_nat0_outbound extended permit ip 192.168.5.0 255.255.255.0 A-inside-VLAN12 255.255.255.0
    access-list outside_cryptomap extended permit ip fw-inside-subnet 255.255.255.0 B-inside-subnet 255.255.255.0
    access-list Outside_nat-inbound extended permit ip A-inside-VLAN12 255.255.255.0 192.168.5.0 255.255.255.0
    access-list Outside_nat-inbound extended permit ip host A-forti 192.168.5.0 255.255.255.0
    access-list outside_1_cryptomap extended permit ip 192.168.5.0 255.255.255.0 A-inside-VLAN12 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-631.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 101 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 101 0.0.0.0 0.0.0.0
    route outside 0.0.0.0 0.0.0.0 81 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http B-inside-subnet 255.255.255.0 inside
    http fw-inside-subnet 255.255.255.0 inside
    http 0.0.0.0 255.255.255.255 outside
    http 0.0.0.0 0.0.0.0 outside
    http 192.168.5.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer A-forti
    crypto map outside_map 1 set transform-set ESP-3DES-SHA
    crypto map outside_map 2 match address outside_cryptomap
    crypto map outside_map 2 set peer B-firewall
    crypto map outside_map 2 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto isakmp policy 20
    authentication pre-share
    encryption aes-192
    hash md5
    group 2
    lifetime 86400
    crypto isakmp policy 30
    authentication pre-share
    encryption aes-256
    hash md5
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    dhcpd address 192.168.5.10-192.168.5.20 inside
    dhcpd dns 165 165 interface inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy DfltGrpPolicy attributes
    vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
    username admin password XXX encrypted privilege 15
    tunnel-group 122 type ipsec-l2l
    tunnel-group 122 ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    class-map outside-class
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
      message-length maximum client auto
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect icmp
    policy-map outside-policy
    description ok
    class outside-class
      inspect dns
      inspect esmtp
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect icmp
      inspect icmp error
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect sip
      inspect skinny
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect xdmcp
    service-policy global_policy global
    service-policy outside-policy interface outside
    prompt hostname context
    Cryptochecksum: XXX
    : end
    Kindly need your expertise&help to solve the problem

    any1 can help me ?

  • Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall

    Hi,
    I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
    When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
    After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
    They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
    Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
    3
    Nov 21 2012
    07:11:09
    713902
    Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
    3
    Nov 21 2012
    07:11:09
    713902
    Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
    3
    Nov 21 2012
    07:11:09
    713061
    Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
    5
    Nov 21 2012
    07:11:09
    713119
    Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
    Here is from the syntax: show crypto isakmp sa
    Result of the command: "show crypto isakmp sa"
       Active SA: 1
        Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
    Total IKE SA: 1
    1   IKE Peer: 195.149.180.254
        Type    : L2L             Role    : responder
        Rekey   : no              State   : MM_ACTIVE
    Result of the command: "show crypto ipsec sa"
    interface: outside
        Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
          access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
          local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
          current_peer:195.149.180.254
          #pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
          #pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
          #pkts compressed: 0, #pkts decompressed: 0
          #pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
          #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
          #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
          #send errors: 0, #recv errors: 0
          local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
          path mtu 1500, ipsec overhead 74, media mtu 1500
          current outbound spi: E715B315
        inbound esp sas:
          spi: 0xFAC769EB (4207372779)
             transform: esp-aes-256 esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, PFS Group 5, }
             slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
             sa timing: remaining key lifetime (kB/sec): (38738/2061)
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0xFFFFFFFF 0xFFFFFFFF
        outbound esp sas:
          spi: 0xE715B315 (3876958997)
             transform: esp-aes-256 esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, PFS Group 5, }
             slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
             sa timing: remaining key lifetime (kB/sec): (38673/2061)
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001
    And here are my Accesslists and vpn site to site config:
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 84600
    crypto isakmp nat-traversal 40
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto map CustomerCryptoMap 10 match address VPN_Tunnel
    crypto map CustomerCryptoMap 10 set pfs group5
    crypto map CustomerCryptoMap 10 set peer 195.149.180.254
    crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
    crypto map CustomerCryptoMap interface outside
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
    nat (inside) 0 access-list nonat
    All these remote networks are at the Main Site Clavister Firewall.
    Best Regards
    Michael

    Hi,
    I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
    If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
    Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
    I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
    Maybe you could try to change the Encryption Domain configurations a bit and test it then.
    You could also maybe take some debugs on the Phase2 and see if you get anymore  hints as to what could be the problem when only one network is working for the L2L VPN.
    - Jouni

  • Setting up site to site vpn with cisco asa 5505

    I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
    IP of remote office router is 71.37.178.142
    IP of the main office firewall is 209.117.141.82
    Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
    ciscoasa# show run
    : Saved
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password TMACBloMlcBsq1kp encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs group5
    crypto map outside_map 1 set peer 209.117.141.82
    crypto map outside_map 1 set transform-set ESP-AES-256-SHA
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn username [email protected] password ********* store-local
    dhcpd auto_config outside
    dhcpd address 192.168.1.2-192.168.1.129 inside
    dhcpd enable inside
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
    : end
    ciscoasa#
    Thanks!

    Hi Mandy,
    By using following access list define Peer IP as source and destination
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    you are not defining the interesting traffic / subnets from both ends.
    Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
    !.1..source subnet(called local encryption domain) at your end  192.168.200.0
    !..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
    !..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
    !...at your end  192.168.200.0
    !..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
    !...at other end 192.168.100.0
    Please use Baisc Steps as follows:
    A. Configuration in your MAIN office  having IP = 209.117.141.82  (follow step 1 to 6)
    Step 1.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    Step 2.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 3.
    Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 71.37.178.142
    or , but not both
    crypto isakmp key 6 CISCO123 address71.37.178.142
    step 4.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 5.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 6.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Configure the same but just change ACL on other end in step one  by reversing source and destination
    and also set the peer IP of this router in other end.
    So other side config should look as follows:
    B.  Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
    Step 7.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
    Step 8.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 9.
    Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 209.117.141.82
    or , but not both
    crypto isakmp key 6 CISCO123 address 209.117.141.82
    step 10.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 11.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map    ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set, only one is permissible
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 12.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Now initite a ping
    Here is for your summary:
    IPSec: Site to Site - Routers
    Configuration Steps
    Phase 1
    Step 1: Configure Mirrored ACL/Crypto ACL       for Interesting Traffic
    Step 2: Configure ISAKMP Policy
    Step 3: Configure ISAKMP Key
    Phase 2
    Step 4: Configure Transform Set
    Step 5: Configure Crypto Map
    Step 6: Apply Crypto Map to an Interface
    To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
    Router#debug crpyto isakmp
    Router#debug crpyto ipsec
    Router(config)# logging buffer 7
    Router(config)# logging buffer 99999
    Router(config)# logging console 6
    Router# clear logging
    Configuration
    In R1:
    (config)# access-list 101 permit ipo host 10.1.1.1 host      10.1.2.1
    (config)# crypto isakmp policy 10
    (config-policy)# encryption 3des
    (config-policy)# authentication pre-share
    (config-policy)# group 2
    (config-policy)# hash sha1
    (config)# crypto isakmp key 0 cisco address 2.2.2.1
    (config)# crypto ipsec transform-set TSET esp-3des      sha-aes-hmac
    (config)# crypto map CMAP 10 ipsec-isakmp
    (config-crypto-map)# set peer 2.2.2.1
    (config-crypto-map)# match address 101
    (config-crypto-map)# set transform-set TSET
    (config)# int f0/0
    (config-if)# crypto map CMAP
    Similarly in R2
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Change to Transport Mode, add the following command in Step 4:
    (config-tranform-set)# mode transport
    Even after  doing this change, the ipsec negotiation will still be done through  tunnel mode if pinged from Loopback to Loopback. To overcome this we  make changes to ACL.
    Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
    (config)# crypto isakmp peer address 2.2.2.1
    (config-peer)# set aggressive-mode password cisco
    (config-peer)# set aggressive-mode clien-endpoint       ipv4-address 2.2.2.1
    Similarly on R2.
    The below process is for the negotiation using RSA-SIG (PKI) as authentication type
    Debug Process:
    After  we debug, we can see the negotiation between the two peers. The first  packet of the interesting traffic triggers the ISAKMP (Phase1)  negotiation. Important messages are marked in BOLD and explanation in  RED
    R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
    Packet sent with a source address of 2.2.2.2
    Mar  2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) //  Router tried to find any IPSec SA matching the outgoing connection but  no valid SA has been found in Security Association Database (SADB)
    Mar  2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
    Mar  2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
    Mar  2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
    Mar  2 16:18:42.939: ISAKMP: local port 500, remote port 500
    Mar  2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE    
    Mar  2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
    Mar  2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
    Mar  2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
    Mar  2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
    Mar  2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY  New State = IKE_I_MM1
    Mar  2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
    Mar  2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1  New State = IKE_I_MM2
    Mar  2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947:.!!!!
    Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
    R2(config)# ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
    Mar  2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
    Mar  2 16:18:42.947: ISAKMP:      encryption 3DES-CBC
    Mar  2 16:18:42.947: ISAKMP:      hash SHA
    Mar  2 16:18:42.947: ISAKMP:      default group 2
    Mar  2 16:18:42.947: ISAKMP:      auth RSA sig
    Mar  2 16:18:42.947: ISAKMP:      life type in seconds
    Mar  2 16:18:42.947: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
    Mar  2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
    Mar  2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
    Mar  2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM2
    Mar  2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
    Mar  2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM3
    Mar  2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
    Mar  2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3  New State = IKE_I_MM4
    Mar  2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
    Mar  2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:43.007:  Choosing trustpoint CA_Server as issuer
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
    Mar  2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM4
    Mar  2 16:18:43.011: ISAKMP:(1008):Send initial contact
    Mar  2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
    Mar  2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
    Mar  2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
    Mar  2 16:18:43.011: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : R2
              protocol     : 17
              port         : 500
              length       : 10
    Mar  2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
    Mar  2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
    Mar  2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
    Mar  2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
    Mar  2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM5
    Mar  2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
    // "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : ASA1
              protocol     : 0
              port         : 0
              length       : 12
    Mar  2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
    Mar  2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
    Mar  2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
    Mar  2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
    Mar  2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
    Mar  2 16:18:43.067: ISAKMP:received payload type 17
    Mar  2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
    Mar  2 16:18:43.067: ISAKMP:(1008):SA authentication status:
              authenticated
    Mar  2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
    Mar  2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/,  and inserted successfully 46519678. // SA inserted into SADB
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5  New State = IKE_I_MM6
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_I_MM6
    Mar  2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
    Mar  2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
    Mar  2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY  New State = IKE_QM_I_QM1
    Mar  2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
    Mar  2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
    Mar  2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
    Mar  2 16:18:43.079: ISAKMP:   attributes in transform:
    Mar  2 16:18:43.079: ISAKMP:      SA life type in seconds
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (basic) of 3600
    Mar  2 16:18:43.079: ISAKMP:      SA life type in kilobytes
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
    Mar  2 16:18:43.079: ISAKMP:      encaps is 1 (Tunnel)
    Mar  2 16:18:43.079: ISAKMP:      authenticator is HMAC-SHA
    Mar  2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
    Mar  2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
    Mar  2 16:18:43.083:         inbound SA from 20.1.1.10 to 40.1.1.1 (f/i)  0/ 0
              (proxy 1.1.1.1 to 2.2.2.2)
    Mar  2 16:18:43.083:         has spi 0xA9A66D46 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083:         outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
              (proxy 2.2.2.2 to 1.1.1.1)
    Mar  2 16:18:43.083:         has spi  0x2B367FB4 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
    Mar  2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
    Mar  2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1  New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Kindly rate if you find the explanation useful !!
    Best Regards
    Sachin Garg

  • Cisco ASA 5505 Site to Site VPN

    Hello All,
    First time posting to the forums. I've been working with Cisco ASA 5505 for a number of months and recently I purchased a 2nd ASA with the goal of setting up Site to Site VPN tunnel. It look so simple from the number of videos that I have watched on the internet. But when I have done it suprise suprise it didn't work for me ... I have deleted the tunnels a number of times and attempted to recreate them. I am using the VPN wizard in the ADM to create the tunnel. Both the asa are 5505 and have the same same firmware etc.
    I would appreciate any help that can be directed towards this issue please.  Slowly losing my mind
    Please see details below:
    Both ADM are 7.1
    IOS
    ASA 1
    aved
    ASA Version 9.0(1)
    hostname PAYBACK
    enable password HSMurh79NVmatjY0 encrypted
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    ip local pool VPN1 192.168.50.1-192.168.50.254 mask 255.255.255.0
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    description Trunk link to SW1
    switchport trunk allowed vlan 1,10,20,30,40
    switchport trunk native vlan 1
    switchport mode trunk
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    no nameif
    no security-level
    no ip address
    interface Vlan2
    nameif outside
    security-level 0
    ip address 92.51.193.158 255.255.255.252
    interface Vlan10
    nameif inside
    security-level 100
    ip address 192.168.10.1 255.255.255.0
    interface Vlan20
    nameif servers
    security-level 100
    ip address 192.168.20.1 255.255.255.0
    interface Vlan30
    nameif printers
    security-level 100
    ip address 192.168.30.1 255.255.255.0
    interface Vlan40
    nameif wireless
    security-level 100
    ip address 192.168.40.1 255.255.255.0
    banner login line Welcome to Payback Loyalty Systems
    boot system disk0:/asa901-k8.bin
    ftp mode passive
    clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup outside
    dns domain-lookup inside
    dns domain-lookup servers
    dns domain-lookup printers
    dns domain-lookup wireless
    dns server-group DefaultDNS
    name-server 83.147.160.2
    name-server 83.147.160.130
    same-security-traffic permit inter-interface
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network ftp_server
    object network Internal_Report_Server
    host 192.168.20.21
    description Automated Report Server Internal Address
    object network Report_Server
    host 89.234.126.9
    description Automated Report Server
    object service RDP
    service tcp destination eq 3389
    description RDP to Server
    object network Host_QA_Server
    host 89.234.126.10
    description QA Host External Address
    object network Internal_Host_QA
    host 192.168.20.22
    description Host of VM machine for QA
    object network Internal_QA_Web_Server
    host 192.168.20.23
    description Web Server in QA environment
    object network Web_Server_QA_VM
    host 89.234.126.11
    description Web server in QA environment
    object service SQL_Server
    service tcp destination eq 1433
    object network Demo_Server
    host 89.234.126.12
    description Server set up to Demo Product
    object network Internal_Demo_Server
    host 192.168.20.24
    description Internal IP Address of Demo Server
    object network NETWORK_OBJ_192.168.20.0_24
    subnet 192.168.20.0 255.255.255.0
    object network NETWORK_OBJ_192.168.50.0_26
    subnet 192.168.50.0 255.255.255.192
    object network NETWORK_OBJ_192.168.0.0_16
    subnet 192.168.0.0 255.255.0.0
    object service MSSQL
    service tcp destination eq 1434
    description MSSQL port
    object network VPN-network
    subnet 192.168.50.0 255.255.255.0
    object network NETWORK_OBJ_192.168.50.0_24
    subnet 192.168.50.0 255.255.255.0
    object service TS
    service tcp destination eq 4400
    object service TS_Return
    service tcp source eq 4400
    object network External_QA_3
    host 89.234.126.13
    object network Internal_QA_3
    host 192.168.20.25
    object network Dev_WebServer
    host 192.168.20.27
    object network External_Dev_Web
    host 89.234.126.14
    object network CIX_Subnet
    subnet 192.168.100.0 255.255.255.0
    object network NETWORK_OBJ_192.168.10.0_24
    subnet 192.168.10.0 255.255.255.0
    object network NETWORK_OBJ_84.39.233.50
    host 84.39.233.50
    object network NETWORK_OBJ_92.51.193.158
    host 92.51.193.158
    object network NETWORK_OBJ_192.168.100.0_24
    subnet 192.168.100.0 255.255.255.0
    object network NETWORK_OBJ_192.168.1.0_24
    subnet 192.168.1.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_1
    service-object tcp destination eq ftp
    service-object tcp destination eq netbios-ssn
    service-object tcp destination eq smtp
    service-object object TS
    object-group network Payback_Internal
    network-object 192.168.10.0 255.255.255.0
    network-object 192.168.20.0 255.255.255.0
    network-object 192.168.40.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_3
    service-object tcp destination eq www
    service-object tcp destination eq https
    service-object object TS
    service-object object TS_Return
    object-group service DM_INLINE_SERVICE_4
    service-object object RDP
    service-object tcp destination eq www
    service-object tcp destination eq https
    object-group service DM_INLINE_SERVICE_5
    service-object object MSSQL
    service-object object RDP
    service-object object TS
    object-group protocol TCPUDP
    protocol-object udp
    protocol-object tcp
    object-group service DM_INLINE_SERVICE_6
    service-object object TS
    service-object object TS_Return
    service-object tcp destination eq www
    service-object tcp destination eq https
    access-list outside_access_in remark This rule is allowing from internet to interal server.
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark FTP
    access-list outside_access_in remark RDP
    access-list outside_access_in remark SMTP
    access-list outside_access_in remark Net Bios
    access-list outside_access_in remark SQL
    access-list outside_access_in remark TS - 4400
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any4 object Internal_Report_Server
    access-list outside_access_in remark Access rule to internal host QA
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark HTTP
    access-list outside_access_in remark RDP
    access-list outside_access_in extended permit tcp any4 object Internal_Host_QA eq www
    access-list outside_access_in remark Access to INternal Web Server:
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark HTTP
    access-list outside_access_in remark RDP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 any4 object Internal_QA_Web_Server
    access-list outside_access_in remark Rule for allowing access to Demo server
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark RDP
    access-list outside_access_in remark MSSQL
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any4 object Internal_Demo_Server
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
    access-list outside_access_in remark Access for Development WebServer
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
    access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
    access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
    access-list AnyConnect_Client_Local_Print remark Windows' printing port
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
    access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
    access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
    access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
    access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
    access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
    access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
    access-list Payback_VPN_splitTunnelAcl standard permit 192.168.20.0 255.255.255.0
    access-list outside_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
    pager lines 24
    logging enable
    logging console informational
    logging asdm informational
    logging from-address
    [email protected]
    logging recipient-address
    [email protected]
    level alerts
    mtu outside 1500
    mtu inside 1500
    mtu servers 1500
    mtu printers 1500
    mtu wireless 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-711-52.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,outside) source dynamic any interface
    nat (wireless,outside) source dynamic any interface
    nat (servers,outside) source dynamic any interface
    nat (servers,outside) source static Internal_Report_Server Report_Server
    nat (servers,outside) source static Internal_Host_QA Host_QA_Server
    nat (servers,outside) source static Internal_QA_Web_Server Web_Server_QA_VM
    nat (servers,outside) source static Internal_Demo_Server Demo_Server
    nat (servers,outside) source static NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 destination static NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 no-proxy-arp route-lookup
    nat (servers,outside) source static Internal_QA_3 External_QA_3
    nat (servers,outside) source static Dev_WebServer External_Dev_Web
    nat (inside,outside) source static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
    nat (inside,outside) source static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.10.0 255.255.255.0 inside
    http 192.168.40.0 255.255.255.0 wireless
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer 84.39.233.50
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
    crypto map outside_map interface outside
    crypto ca trustpool policy
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside client-services port 443
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh 77.75.100.208 255.255.255.240 outside
    ssh 192.168.10.0 255.255.255.0 inside
    ssh 192.168.40.0 255.255.255.0 wireless
    ssh timeout 5
    console timeout 0
    dhcpd dns 192.168.0.1
    dhcpd auto_config outside
    dhcpd address 192.168.10.21-192.168.10.240 inside
    dhcpd dns 192.168.20.21 83.147.160.2 interface inside
    dhcpd option 15 ascii paybackloyalty.com interface inside
    dhcpd enable inside
    dhcpd address 192.168.40.21-192.168.40.240 wireless
    dhcpd dns 192.168.20.21 83.147.160.2 interface wireless
    dhcpd update dns interface wireless
    dhcpd option 15 ascii paybackloyalty.com interface wireless
    dhcpd enable wireless
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy Payback_VPN internal
    group-policy Payback_VPN attributes
    vpn-simultaneous-logins 10
    vpn-tunnel-protocol ikev1
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Payback_VPN_splitTunnelAcl
    group-policy DfltGrpPolicy attributes
    dns-server value 83.147.160.2 83.147.160.130
    vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
    group-policy GroupPolicy_84.39.233.50 internal
    group-policy GroupPolicy_84.39.233.50 attributes
    vpn-tunnel-protocol ikev1 ikev2
    username Noelle password XB/IpvYaATP.2QYm encrypted
    username Noelle attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Eanna password vXILR9ZZQIsd1Naw encrypted privilege 0
    username Eanna attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Michael password qpbleUqUEchRrgQX encrypted
    username Michael attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Danny password .7fEXdzESUk6S/cC encrypted privilege 0
    username Danny attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Aileen password tytrelqvV5VRX2pz encrypted privilege 0
    username Aileen attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Aidan password aDu6YH0V5XaxpEPg encrypted privilege 0
    username Aidan attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
    username shane.c password iqGMoWOnfO6YKXbw encrypted
    username shane.c attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Shane password uYePLcrFadO9pBZx encrypted
    username Shane attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username James password TdYPv1pvld/hPM0d encrypted
    username James attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username mark password yruxpddqfyNb.qFn encrypted
    username mark attributes
    service-type admin
    username Mary password XND5FTEiyu1L1zFD encrypted
    username Mary attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Massimo password vs65MMo4rM0l4rVu encrypted privilege 0
    username Massimo attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    tunnel-group Payback_VPN type remote-access
    tunnel-group Payback_VPN general-attributes
    address-pool VPN1
    default-group-policy Payback_VPN
    tunnel-group Payback_VPN ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group 84.39.233.50 type ipsec-l2l
    tunnel-group 84.39.233.50 general-attributes
    default-group-policy GroupPolicy_84.39.233.50
    tunnel-group 84.39.233.50 ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map global-class
    match default-inspection-traffic
    policy-map global-policy
    class global-class
      inspect dns
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect ip-options
      inspect netbios
      inspect pptp
      inspect rsh
      inspect rtsp
      inspect sip
      inspect snmp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect xdmcp
      inspect icmp error
      inspect icmp
    service-policy global-policy global
    smtp-server 192.168.20.21
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1
    ASA 2
    ASA Version 9.0(1)
    hostname Payback-CIX
    enable password HSMurh79NVmatjY0 encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    description This port connects to VLAN 100
    switchport access vlan 100
    interface Ethernet0/2
    interface Ethernet0/3
    switchport access vlan 100
    interface Ethernet0/4
    switchport access vlan 100
    interface Ethernet0/5
    switchport access vlan 100
    interface Ethernet0/6
    switchport access vlan 100
    interface Ethernet0/7
    switchport access vlan 100
    interface Vlan2
    nameif outside
    security-level 0
    ip address 84.39.233.50 255.255.255.240
    interface Vlan100
    nameif inside
    security-level 100
    ip address 192.168.100.1 255.255.255.0
    banner login line Welcome to Payback Loyalty - CIX
    ftp mode passive
    clock summer-time gmt/idt recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup outside
    dns domain-lookup inside
    dns server-group defaultDNS
    name-server 8.8.8.8
    name-server 8.8.4.4
    same-security-traffic permit inter-interface
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network CIX-Host-1
    host 192.168.100.2
    description This is the host machine of the VM servers
    object network External_CIX-Host-1
    host 84.39.233.51
    description This is the external IP address of the host server for the VM server
    object service RDP
    service tcp source range 1 65535 destination eq 3389
    object network Payback_Office
    host 92.51.193.158
    object service MSQL
    service tcp destination eq 1433
    object network Development_OLTP
    host 192.168.100.10
    description VM for Eiresoft
    object network External_Development_OLTP
    host 84.39.233.52
    description This is the external IP address for the VM for Eiresoft
    object network Eiresoft
    host 146.66.160.70
    description DBA Contractor
    object network External_TMC_Web
    host 84.39.233.53
    description Public Address of TMC Webserver
    object network TMC_Webserver
    host 192.168.100.19
    description Internal Address of TMC Webserver
    object network External_TMC_OLTP
    host 84.39.233.54
    description Targets OLTP external IP
    object network TMC_OLTP
    host 192.168.100.18
    description Targets interal IP address
    object network External_OLTP_Failover
    host 84.39.233.55
    description Public IP of OLTP Failover
    object network OLTP_Failover
    host 192.168.100.60
    description Server for OLTP failover
    object network Servers
    subnet 192.168.20.0 255.255.255.0
    object network Wired
    subnet 192.168.10.0 255.255.255.0
    object network Wireless
    subnet 192.168.40.0 255.255.255.0
    object network NETWORK_OBJ_192.168.100.0_24
    subnet 192.168.100.0 255.255.255.0
    object network NETWORK_OBJ_192.168.10.0_24
    subnet 192.168.10.0 255.255.255.0
    object network Eiresoft_2nd
    host 137.117.217.29
    description Eiresoft 2nd IP
    object network Dev_Test_Webserver
    host 192.168.100.12
    description Dev Test Webserver Internal Address
    object network External_Dev_Test_Webserver
    host 84.39.233.56
    description This is the PB Dev Test Webserver
    object network NETWORK_OBJ_192.168.1.0_24
    subnet 192.168.1.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_1
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_2
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_3
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_4
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_5
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_6
    service-object object MSQL
    service-object object RDP
    object-group network Payback_Intrernal
    network-object object Servers
    network-object object Wired
    network-object object Wireless
    object-group service DM_INLINE_SERVICE_7
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_8
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_9
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_10
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_11
    service-object object RDP
    service-object tcp destination eq ftp
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-Host-1
    access-list outside_access_in remark Development OLTP from Payback Office
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP
    access-list outside_access_in remark Access for Eiresoft
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver
    access-list outside_access_in remark Access to OLTP for target from Payback Office
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover
    access-list outside_access_in remark This is allowing access from Eiresoft to the OLTP Failover server
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover
    access-list outside_access_in remark Access for the 2nd IP from Eiresoft
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP
    access-list outside_access_in remark Access from the 2nd Eiresoft IP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP
    access-list outside_cryptomap extended permit ip 192.168.100.0 255.255.255.0 192.168.10.0 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,outside) source dynamic any interface
    nat (inside,outside) source static CIX-Host-1 External_CIX-Host-1
    nat (inside,outside) source static Development_OLTP External_Development_OLTP
    nat (inside,outside) source static TMC_Webserver External_TMC_Web
    nat (inside,outside) source static TMC_OLTP External_TMC_OLTP
    nat (inside,outside) source static OLTP_Failover External_OLTP_Failover
    nat (inside,outside) source static Dev_Test_Webserver External_Dev_Test_Webserver
    nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 no-proxy-arp route-lookup
    nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 92.51.193.156 255.255.255.252 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer 92.51.193.158
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
    crypto map outside_map interface outside
    crypto ca trustpool policy
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication crack
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication rsa-sig
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 30
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 40
    authentication crack
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 50
    authentication rsa-sig
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 60
    authentication pre-share
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 70
    authentication crack
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 80
    authentication rsa-sig
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 90
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 100
    authentication crack
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 110
    authentication rsa-sig
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 120
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 130
    authentication crack
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 140
    authentication rsa-sig
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 150
    authentication pre-share
    encryption des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh 77.75.100.208 255.255.255.240 outside
    ssh 92.51.193.156 255.255.255.252 outside
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy GroupPolicy_92.51.193.158 internal
    group-policy GroupPolicy_92.51.193.158 attributes
    vpn-tunnel-protocol ikev1 ikev2
    username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
    tunnel-group 92.51.193.158 type ipsec-l2l
    tunnel-group 92.51.193.158 general-attributes
    default-group-policy GroupPolicy_92.51.193.158
    tunnel-group 92.51.193.158 ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
    : end

    Hi,
    Thanks for the help to date
    I now have the Site to Site working but there is one little issue I have. If I try to RD to a server through the tunnel it will not allow connection on the first attempt however if I ping that host and then attempt to RD it will allow the connection. It looks like the host is asleep until it receives traffic through the tunnel. Is this thje correct behaviour.
    See below the details:
    ASA1:
    hostname PAYBACK
    enable password HSMurh79NVmatjY0 encrypted
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    ip local pool VPN1 192.168.50.1-192.168.50.254 mask 255.255.255.0
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    description Trunk link to SW1
    switchport trunk allowed vlan 1,10,20,30,40
    switchport trunk native vlan 1
    switchport mode trunk
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    no nameif
    no security-level
    no ip address
    interface Vlan2
    nameif outside
    security-level 0
    ip address XX.XX.XX.XX 255.255.255.252
    interface Vlan10
    nameif inside
    security-level 100
    ip address 192.168.10.1 255.255.255.0
    interface Vlan20
    nameif servers
    security-level 100
    ip address 192.168.20.1 255.255.255.0
    interface Vlan30
    nameif printers
    security-level 100
    ip address 192.168.30.1 255.255.255.0
    interface Vlan40
    nameif wireless
    security-level 100
    ip address 192.168.40.1 255.255.255.0
    banner login line Welcome to Payback Loyalty Systems
    boot system disk0:/asa901-k8.bin
    ftp mode passive
    clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup outside
    dns domain-lookup inside
    dns domain-lookup servers
    dns domain-lookup printers
    dns domain-lookup wireless
    dns server-group DefaultDNS
    name-server 83.147.160.2
    name-server 83.147.160.130
    same-security-traffic permit inter-interface
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network ftp_server
    object network Internal_Report_Server
    host 192.168.20.21
    description Automated Report Server Internal Address
    object network Report_Server
    host 89.234.126.9
    description Automated Report Server
    object service RDP
    service tcp destination eq 3389
    description RDP to Server
    object network Host_QA_Server
    host 89.234.126.10
    description QA Host External Address
    object network Internal_Host_QA
    host 192.168.20.22
    description Host of VM machine for QA
    object network Internal_QA_Web_Server
    host 192.168.20.23
    description Web Server in QA environment
    object network Web_Server_QA_VM
    host 89.234.126.11
    description Web server in QA environment
    object service SQL_Server
    service tcp destination eq 1433
    object network Demo_Server
    host 89.234.126.12
    description Server set up to Demo Product
    object network Internal_Demo_Server
    host 192.168.20.24
    description Internal IP Address of Demo Server
    object network NETWORK_OBJ_192.168.20.0_24
    subnet 192.168.20.0 255.255.255.0
    object network NETWORK_OBJ_192.168.50.0_26
    subnet 192.168.50.0 255.255.255.192
    object network NETWORK_OBJ_192.168.0.0_16
    subnet 192.168.0.0 255.255.0.0
    object service MSSQL
    service tcp destination eq 1434
    description MSSQL port
    object network VPN-network
    subnet 192.168.50.0 255.255.255.0
    object network NETWORK_OBJ_192.168.50.0_24
    subnet 192.168.50.0 255.255.255.0
    object service TS
    service tcp destination eq 4400
    object service TS_Return
    service tcp source eq 4400
    object network External_QA_3
    host 89.234.126.13
    object network Internal_QA_3
    host 192.168.20.25
    object network Dev_WebServer
    host 192.168.20.27
    object network External_Dev_Web
    host 89.234.126.14
    object network NETWORK_OBJ_192.168.100.0_24
    subnet 192.168.100.0 255.255.255.0
    object network Wireless
    subnet 192.168.40.0 255.255.255.0
    description Wireless network
    object network Servers
    subnet 192.168.20.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_1
    service-object tcp destination eq ftp
    service-object tcp destination eq netbios-ssn
    service-object tcp destination eq smtp
    service-object object TS
    service-object object SQL_Server
    object-group service DM_INLINE_SERVICE_3
    service-object tcp destination eq www
    service-object tcp destination eq https
    service-object object TS
    service-object object TS_Return
    object-group service DM_INLINE_SERVICE_4
    service-object object RDP
    service-object tcp destination eq www
    service-object tcp destination eq https
    object-group service DM_INLINE_SERVICE_5
    service-object object MSSQL
    service-object object RDP
    service-object object TS
    object-group protocol TCPUDP
    protocol-object udp
    protocol-object tcp
    object-group service DM_INLINE_SERVICE_6
    service-object object TS
    service-object object TS_Return
    service-object tcp destination eq www
    service-object tcp destination eq https
    object-group network DM_INLINE_NETWORK_1
    network-object 192.168.10.0 255.255.255.0
    network-object 192.168.20.0 255.255.255.0
    network-object 192.168.40.0 255.255.255.0
    object-group network Payback_Internal
    network-object 192.168.10.0 255.255.255.0
    network-object 192.168.20.0 255.255.255.0
    network-object 192.168.40.0 255.255.255.0
    access-list outside_access_in remark This rule is allowing from internet to interal server.
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark FTP
    access-list outside_access_in remark RDP
    access-list outside_access_in remark SMTP
    access-list outside_access_in remark Net Bios
    access-list outside_access_in remark SQL
    access-list outside_access_in remark TS - 4400
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any4 object Internal_Report_Server
    access-list outside_access_in remark Access rule to internal host QA
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark HTTP
    access-list outside_access_in remark RDP
    access-list outside_access_in extended permit tcp any4 object Internal_Host_QA eq www
    access-list outside_access_in remark Access to INternal Web Server:
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark HTTP
    access-list outside_access_in remark RDP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 any4 object Internal_QA_Web_Server
    access-list outside_access_in remark Rule for allowing access to Demo server
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark RDP
    access-list outside_access_in remark MSSQL
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any4 object Internal_Demo_Server
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
    access-list outside_access_in remark Access for Development WebServer
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
    access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
    access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
    access-list AnyConnect_Client_Local_Print remark Windows' printing port
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
    access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
    access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
    access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
    access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
    access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
    access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
    access-list Payback_VPN_splitTunnelAcl standard permit 192.168.20.0 255.255.255.0
    access-list outside_cryptomap extended permit ip object-group DM_INLINE_NETWORK_1 192.168.100.0 255.255.255.0
    pager lines 24
    logging enable
    logging console informational
    logging asdm informational
    logging from-address [email protected]
    logging recipient-address [email protected] level alerts
    mtu outside 1500
    mtu inside 1500
    mtu servers 1500
    mtu printers 1500
    mtu wireless 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-711-52.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,outside) source static DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
    nat (wireless,outside) source static Wireless Wireless destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
    nat (servers,outside) source static Servers Servers destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
    nat (inside,outside) source dynamic any interface
    nat (wireless,outside) source dynamic any interface
    nat (servers,outside) source dynamic any interface
    nat (servers,outside) source static Internal_Report_Server Report_Server
    nat (servers,outside) source static Internal_Host_QA Host_QA_Server
    nat (servers,outside) source static Internal_QA_Web_Server Web_Server_QA_VM
    nat (servers,outside) source static Internal_Demo_Server Demo_Server
    nat (servers,outside) source static NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 destination static NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 no-proxy-arp route-lookup
    nat (servers,outside) source static Internal_QA_3 External_QA_3
    nat (servers,outside) source static Dev_WebServer External_Dev_Web
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.10.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer XX.XX.XX.XX
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map inside_map interface inside
    crypto map servers_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map servers_map interface servers
    crypto ca trustpool policy
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside client-services port 443
    crypto ikev2 enable inside client-services port 443
    crypto ikev1 enable outside
    crypto ikev1 enable inside
    crypto ikev1 enable servers
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh 192.168.10.0 255.255.255.0 inside
    ssh timeout 5
    console timeout 0
    dhcpd dns 192.168.0.1
    dhcpd auto_config outside
    dhcpd address 192.168.10.21-192.168.10.240 inside
    dhcpd dns 192.168.20.21 83.147.160.2 interface inside
    dhcpd option 15 ascii paybackloyalty.com interface inside
    dhcpd enable inside
    dhcpd address 192.168.40.21-192.168.40.240 wireless
    dhcpd dns 192.168.20.21 83.147.160.2 interface wireless
    dhcpd update dns interface wireless
    dhcpd option 15 ascii paybackloyalty.com interface wireless
    dhcpd enable wireless
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy Payback_VPN internal
    group-policy Payback_VPN attributes
    vpn-simultaneous-logins 10
    vpn-tunnel-protocol ikev1
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Payback_VPN_splitTunnelAcl
    group-policy DfltGrpPolicy attributes
    dns-server value 83.147.160.2 83.147.160.130
    vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
    group-policy GroupPolicy_84.39.233.50 internal
    group-policy GroupPolicy_84.39.233.50 attributes
    vpn-tunnel-protocol ikev1 ikev2
    username Noelle password XB/IpvYaATP.2QYm encrypted
    username Noelle attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Eanna password vXILR9ZZQIsd1Naw encrypted privilege 0
    username Eanna attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Michael password qpbleUqUEchRrgQX encrypted
    username Michael attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Danny password .7fEXdzESUk6S/cC encrypted privilege 0
    username Danny attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username niamh password MlFlIlEiy8vismE0 encrypted
    username niamh attributes
    service-type admin
    username Aileen password tytrelqvV5VRX2pz encrypted privilege 0
    username Aileen attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Aidan password aDu6YH0V5XaxpEPg encrypted privilege 0
    username Aidan attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
    username shane.c password iqGMoWOnfO6YKXbw encrypted
    username shane.c attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Shane password yQeVtvLLKqapoUje encrypted privilege 0
    username Shane attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username James password TdYPv1pvld/hPM0d encrypted
    username James attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username mark password yruxpddqfyNb.qFn encrypted
    username mark attributes
    service-type admin
    username Mary password XND5FTEiyu1L1zFD encrypted
    username Mary attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Massimo password vs65MMo4rM0l4rVu encrypted privilege 0
    username Massimo attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    tunnel-group Payback_VPN type remote-access
    tunnel-group Payback_VPN general-attributes
    address-pool VPN1
    default-group-policy Payback_VPN
    tunnel-group Payback_VPN ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group 84.39.233.50 type ipsec-l2l
    tunnel-group 84.39.233.50 general-attributes
    default-group-policy GroupPolicy_84.39.233.50
    tunnel-group 84.39.233.50 ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map global-class
    match default-inspection-traffic
    policy-map global-policy
    class global-class
      inspect dns
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect ip-options
      inspect netbios
      inspect pptp
      inspect rsh
      inspect rtsp
      inspect sip
      inspect snmp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect xdmcp
      inspect icmp error
      inspect icmp
    service-policy global-policy global
    smtp-server 192.168.20.21
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:83fa7ce1d93375645205f6e79b526381
    ASA2:
    ASA Version 9.0(1)
    hostname Payback-CIX
    enable password HSMurh79NVmatjY0 encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    description This port connects to VLAN 100
    switchport access vlan 100
    interface Ethernet0/2
    interface Ethernet0/3
    switchport access vlan 100
    interface Ethernet0/4
    switchport access vlan 100
    interface Ethernet0/5
    switchport access vlan 100
    interface Ethernet0/6
    switchport access vlan 100
    interface Ethernet0/7
    switchport access vlan 100
    interface Vlan2
    nameif outside
    security-level 0
    ip address X.X.X.X 255.255.255.240
    interface Vlan100
    nameif inside
    security-level 100
    ip address 192.168.100.1 255.255.255.0
    banner login line Welcome to Payback Loyalty - CIX
    ftp mode passive
    clock timezone GMT 0
    clock summer-time gmt/idt recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup outside
    dns domain-lookup inside
    dns server-group defaultDNS
    name-server 8.8.8.8
    name-server 8.8.4.4
    same-security-traffic permit inter-interface
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network CIX-Host-1
    host 192.168.100.2
    description This is the host machine of the VM servers
    object network External_CIX-Host-1
    host 84.39.233.51
    description This is the external IP address of the host server for the VM server
    object service RDP
    service tcp source range 1 65535 destination eq 3389
    object network Payback_Office
    host 92.51.193.158
    object service MSQL
    service tcp destination eq 1433
    object network Development_OLTP
    host 192.168.100.10
    description VM for Eiresoft
    object network External_Development_OLTP
    host 84.39.233.52
    description This is the external IP address for the VM for Eiresoft
    object network External_TMC_Web
    host 84.39.233.53
    description Public Address of TMC Webserver
    object network TMC_Webserver
    host 192.168.100.19
    description Internal Address of TMC Webserver
    object network External_TMC_OLTP
    host 84.39.233.54
    description Targets OLTP external IP
    object network TMC_OLTP
    host 192.168.100.18
    description Targets interal IP address
    object network External_OLTP_Failover
    host 84.39.233.55
    description Public IP of OLTP Failover
    object network OLTP_Failover
    host 192.168.100.60
    description Server for OLTP failover
    object network Servers
    subnet 192.168.20.0 255.255.255.0
    object network Wired
    subnet 192.168.10.0 255.255.255.0
    object network Wireless
    subnet 192.168.40.0 255.255.255.0
    object network NETWORK_OBJ_192.168.100.0_24
    subnet 192.168.100.0 255.255.255.0
    object network NETWORK_OBJ_192.168.10.0_24
    subnet 192.168.10.0 255.255.255.0
    object network Eiresoft_2nd
    host 137.117.217.29
    description Eiresoft 2nd IP
    object network Dev_Test_Webserver
    host 192.168.100.12
    description Dev Test Webserver Internal Address
    object network External_Dev_Test_Webserver
    host 84.39.233.56
    description This is the PB Dev Test Webserver
    object network NETWORK_OBJ_192.168.1.0_24
    subnet 192.168.1.0 255.255.255.0
    object network LAN
    subnet 192.168.100.0 255.255.255.0
    object network REMOTE-LAN
    subnet 192.168.10.0 255.255.255.0
    object network TargetMC
    host 83.71.194.145
    description This is Target Location that will be accessing the Webserver
    object network Rackspace_OLTP
    host 162.13.34.56
    description This is the IP address of production OLTP
    object service DB
    service tcp destination eq 5022
    object network Topaz_Target_VM
    host 82.198.151.168
    description This is Topaz IP that will be accessing Targets VM
    object service DB_2
    service tcp destination eq 5023
    object network EireSoft_NEW_IP
    host 146.66.161.3
    description Eiresoft latest IP form ISP DHCP
    object-group service DM_INLINE_SERVICE_1
    service-object object MSQL
    service-object object RDP
    service-object icmp echo
    service-object icmp echo-reply
    object-group service DM_INLINE_SERVICE_2
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_4
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    service-object tcp destination eq www
    object-group service DM_INLINE_SERVICE_5
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_6
    service-object object MSQL
    service-object object RDP
    object-group network Payback_Intrernal
    network-object object Servers
    network-object object Wired
    network-object object Wireless
    object-group service DM_INLINE_SERVICE_8
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_9
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_10
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    service-object icmp echo
    service-object icmp echo-reply
    service-object object DB
    object-group service DM_INLINE_SERVICE_11
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_12
    service-object object MSQL
    service-object icmp echo
    service-object icmp echo-reply
    service-object object DB
    service-object object DB_2
    object-group service DM_INLINE_SERVICE_13
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_14
    service-object object MSQL
    service-object object RDP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-Host-1
    access-list outside_access_in remark Development OLTP from Payback Office
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver
    access-list outside_access_in remark Access to OLTP for target from Payback Office
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover
    access-list outside_access_in remark Access for the 2nd IP from Eiresoft
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP
    access-list outside_access_in remark Access from the 2nd Eiresoft IP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP
    access-list outside_access_in remark Access rules from Traget to CIX for testing
    access-list outside_access_in extended permit tcp object TargetMC object TMC_Webserver eq www
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_12 object Rackspace_OLTP object OLTP_Failover
    access-list outside_access_in remark Topaz access to Target VM
    access-list outside_access_in extended permit tcp object Topaz_Target_VM object TMC_Webserver eq www
    access-list outside_access_in remark Opened up for Target for the weekend. Closing on Monday 20th
    access-list outside_access_in extended permit tcp any object TMC_Webserver eq www
    access-list outside_access_in remark Access for Eiresoft after their ISP changed their IP Address
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_13 object EireSoft_NEW_IP object Development_OLTP
    access-list outside_access_in remark Eiresoft Access after ISP changed their IP Address
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_14 object EireSoft_NEW_IP object OLTP_Failover
    access-list outside_cryptomap extended permit ip 192.168.100.0 255.255.255.0 object-group Payback_Intrernal
    pager lines 24
    logging enable
    logging console debugging
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static Payback_Intrernal Payback_Intrernal no-proxy-arp route-lookup
    nat (inside,outside) source static CIX-Host-1 External_CIX-Host-1
    nat (inside,outside) source static Development_OLTP External_Development_OLTP
    nat (inside,outside) source static TMC_Webserver External_TMC_Web
    nat (inside,outside) source static TMC_OLTP External_TMC_OLTP
    nat (inside,outside) source static OLTP_Failover External_OLTP_Failover
    nat (inside,outside) source static Dev_Test_Webserver External_Dev_Test_Webserver
    nat (inside,outside) source dynamic LAN interface
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http X.X.X.X 255.255.255.252 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer X.X.X.X
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
    crypto map outside_map interface outside
    crypto ca trustpool policy
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication crack
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication rsa-sig
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 30
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 40
    authentication crack
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 50
    authentication rsa-sig
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 60
    authentication pre-share
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 70
    authentication crack
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 80
    authentication rsa-sig
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 90
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 100
    authentication crack
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 110
    authentication rsa-sig
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 120
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 130
    authentication crack
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 140
    authentication rsa-sig
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 150
    authentication pre-share
    encryption des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh X.X.X.X  255.255.255.240 outside
    ssh X.X.X.X 255.255.255.252 outside
    ssh 192.168.40.0 255.255.255.0 outside
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy GroupPolicy_92.51.193.158 internal
    group-policy GroupPolicy_92.51.193.158 attributes
    vpn-tunnel-protocol ikev1 ikev2
    username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
    tunnel-group 92.51.193.158 type ipsec-l2l
    tunnel-group 92.51.193.158 general-attributes
    default-group-policy GroupPolicy_92.51.193.158
    tunnel-group 92.51.193.158 ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:78a7b9ccec2fa048306092eb29a2b769

  • Cisco ASA 5505 SSL VPN

    Hi Everyone,
    In my study home lab, I wanted to configure a cisco ASA 5505 ( Base license) to allow SSL VPN. I follow carefully the configuration procedure as instructed on a short videos I downloaded on youtube.
    I configured my outside e0/0 with a valid static IP address, unfortunately the vpn connection is timeout on a remote ( different) internet connection. But if  I connect to my own internet line using a WIFI the VPN ( AnyConnect SSL VPN client ) connection is established.
    I need help to solve this mystery. Please find attached the ASA config: #show run
    I hope my explaination does make sense, if not accept my apology I am just new in cisco technology.
    Best regards,
    BEN

    If you can connect with your own internet line, then most probably it's not an issue with the ASA configuration.
    I would check how you are routing the ASA to the internet, and if there is any ACL that might be blocking inbound access to the ASA on the device in front of the ASA.

  • Cisco ASA 5505 Site to Site VPN Problem

    Hi All,
    We have a site to site VPN with a cisco asa 5505 on one end and a Checkpoint firewall on the other end.
    We can establish the vpn tunnel and all users in the remote office are working great. However at a random point during the day or it may even be after 2 weeks of working, the tunnel between the sites automatically fails.
    When I dial into the modem which is connected to the firewall I see the following messages in the logs:
    Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
    Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
    Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
    Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
    Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
    Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
    Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
    Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
    Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
    Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
    Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
    Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
    There is nothing in the Checkpoint logs. To solve the issue I have to reload the firewall.
    I have checked both firewalls for any mis-matched parameters and do not see any.
    Any help is very much appreciated as it is very frustrating for myself and the users in the remote office.
    Thanks!

    Also to note, PFS is enabled on both firewalls. Config on Cisco ASA firewall as follows:
    hostname
    domain-name
    enable passwordpasswd names
    interface Vlan701
    nameif inside
    security-level 100
    ip address 10.65.0.69 255.255.255.252
    interface Vlan999
    nameif outside
    security-level 0
    ip address ******  255.255.255.248
    interface Ethernet0/0
    description Link to Internet
    switchport access vlan 999
    interface Ethernet0/1
    description
    switchport access vlan 701
    interface range Ethernet0/2 - 0/7
    switchport access vlan 2
    shutdown
    ftp mode passive
    dns server-group DefaultDNS
    domain-name******
    access-list 101 extended permit ip host ****** 172.25.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 host ******
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 ******* 255.255.255.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 ******** 255.255.255.0
    pager lines 24
    logging enable
    logging timestamp
    logging buffered warnings
    logging trap warnings
    logging asdm informational
    logging host outside *****
    mtu inside 1500
    mtu outside 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm history enable
    arp timeout 14400
    nat (inside) 0 access-list nonat
    route inside ******
    route outside 0.0.0.0 0.0.0.0 ********
    timeout xlate 0:05:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server RADIUS protocol radius
    aaa authentication ssh console LOCAL
    aaa authentication telnet console LOCAL
    snmp-server location **:
    snmp-server contact **
    snmp-server community shortkey
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    snmp-server enable traps syslog
    crypto ipsec transform-set 3desmd5 esp-3des esp-md5-hmac
    crypto map CASGMAP 50 match address 101
    crypto map CASGMAP 50 set pfs group1
    crypto map CASGMAP 50 set peer ********
    crypto map CASGMAP 50 set transform-set 3desmd5
    crypto map CASGMAP 50 set security-association lifetime seconds 3600
    crypto map CASGMAP interface outside
    crypto isakmp enable outside
    crypto isakmp policy 20
    authentication pre-share
    encryption 3des
    hash md5
    group 2
    lifetime 86400
    telnet **** inside
    telnet timeout 5
    ssh **** inside
    ssh **** outside
    ssh timeout 5
    console timeout 30
    management-access inside
    dhcpd ping_timeout 750
    priority-queue outside
    ntp server **
    username ***
    tunnel-group ******** type ipsec-l2l
    tunnel-group ******** ipsec-attributes
    pre-shared-key ***
    class-map VoIP
    match dscp ef
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map General-purpose
    class VoIP
    priority
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect skinny
      inspect esmtp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect sip
      inspect xdmcp
      inspect http
    service-policy General-purpose interface outside
    prompt hostname context

  • VPN PROBLEM CISCO ASA 5505

        Hello,  I have been trying to configure a VPN with Cisco Asa 5505 and Cisco VPN client 5.X for 3 weeks and I am not being able to accomplish it, so I decided to reset to factory defaults and start over again.
         I used ASDM 6.4 VPN wizard to configure it (I selected exempt local network from NAT and enabled split tunneling, but I have tried other combinations as well).
         Tunnel seems to be established properly since I do see an endpoint while using 'sh crypto isakmp sa' but 'sh crypto ipsec sa' shows no packets encrypted or decrypted, so VPN is not working as expected. I can't ping or rdp to internal LAN:
         #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
          #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
         The running-config it created is:
    ciscoasa# sh run
    : Saved
    ASA Version 8.4(2)
    hostname ciscoasa
    enable password XXXX encrypted
    passwd XXXX encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 172.16.1.254 255.255.0.0
    interface Vlan2
    nameif outside
    security-level 0
    pppoe client vpdn group ADSL_Telefonica
    ip address pppoe setroute
    ftp mode passive
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network NETWORK_OBJ_10.0.0.0_24
    subnet 10.0.0.0 255.255.255.0
    object network NETWORK_OBJ_172.16.0.0_16
    subnet 172.16.0.0 255.255.0.0
    access-list test_splitTunnelAcl standard permit 172.16.0.0 255.255.0.0
    pager lines 24
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    ip local pool test 10.0.0.1-10.0.0.254 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_16 NETWORK_OBJ_172.16.0.0_16 destination static NETWORK_OBJ_10.0.0.0_24 NETWORK_OBJ_10.0.0.0_24 no-proxy-arp route-lookup
    object network obj_any
    nat (inside,outside) dynamic interface
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    aaa authentication ssh console LOCAL
    http server enable
    http 172.16.0.0 255.255.0.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet 172.16.0.0 255.255.0.0 inside
    telnet timeout 55
    ssh 172.16.0.0 255.255.0.0 inside
    ssh timeout 55
    console timeout 0
    vpdn group ADSL_Telefonica request dialout pppoe
    vpdn group ADSL_Telefonica localname adslppp@telefonicanetpa
    vpdn group ADSL_Telefonica ppp authentication pap
    vpdn username adslppp@telefonicanetpa password *****
    dhcpd auto_config outside
    dhcpd address 172.16.2.2-172.16.2.129 inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy test internal
    group-policy test attributes
    dns-server value 172.16.1.1
    vpn-tunnel-protocol ikev1
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value test_splitTunnelAcl
    username test password XXXXXX encrypted privilege 0
    username test attributes
    vpn-group-policy test
    username ignacio password XXXXXXX encrypted
    tunnel-group test type remote-access
    tunnel-group test general-attributes
    address-pool test
    default-group-policy test
    tunnel-group test ipsec-attributes
    ikev1 pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:c8935bd572dfd37e81c6aa9f9dc8207c
    : end
    Thank you very much for your help

    Yes, it was a VPN client problem. I was doing test with a WWAN card and it seems it is not compatible with windows 7.
    • The VPN Client on Windows 7 does not support WWAN devices (also called wireless data cards).
    I should have read Release Notes before. Thank you very much for your help and effort.

  • Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)

    Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
    I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
    Please help me to find where is the issue.
    I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
    192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
    Here is my current configuration.
    Thanks for your help.
    IOS Configuration
    version 15.2
    crypto isakmp policy 1
    encr aes 256
    authentication pre-share
    group 2
    crypto isakmp key cisco address 198.0.183.225
    crypto isakmp invalid-spi-recovery
    crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
    mode transport
    crypto map static-map 1 ipsec-isakmp
    set peer S2.S2.S2.S2
    set transform-set AES-SET
    set pfs group2
    match address 100
    interface GigabitEthernet0/0
    ip address S1.S1.S1.S1 255.255.255.240
    ip nat outside
    ip virtual-reassembly in
    duplex auto
    speed auto
    crypto map static-map
    interface GigabitEthernet0/1
    ip address 192.168.17.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    duplex auto
    speed auto
    access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
    ASA Configuration
    ASA Version 8.4(3)
    interface Ethernet0/0
    switchport access vlan 2
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.83.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address S2.S2.S2.S2 255.255.255.248
    ftp mode passive
    same-security-traffic permit intra-interface
    object network inside-network
    subnet 192.168.83.0 255.255.255.0
    object network datacenter
    host S1.S1.S1.S1
    object network datacenter-network
    subnet 192.168.17.0 255.255.255.0
    object network NETWORK_OBJ_192.168.83.0_24
    subnet 192.168.83.0 255.255.255.0
    access-list outside_access_in extended permit icmp any any echo-reply
    access-list outside_access_in extended deny ip any any log
    access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    nat (inside,outside) source dynamic inside-network interface
    nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
    nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
    nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
    crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set vpn-transform-set mode transport
    crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set L2L_SET mode transport
    crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
    crypto map vpn 1 match address outside_cryptomap
    crypto map vpn 1 set pfs
    crypto map vpn 1 set peer S1.S1.S1.S1
    crypto map vpn 1 set ikev1 transform-set L2L_SET
    crypto map vpn 20 ipsec-isakmp dynamic dyno
    crypto map vpn interface outside
    crypto isakmp nat-traversal 3600
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    group-policy GroupPolicy_S1.S1.S1.S1 internal
    group-policy GroupPolicy_S1.S1.S1.S1 attributes
    vpn-tunnel-protocol ikev1
    group-policy remote_vpn_policy internal
    group-policy remote_vpn_policy attributes
    vpn-tunnel-protocol ikev1 l2tp-ipsec
    username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
    username admin password rqiFSVJFung3fvFZ encrypted privilege 15
    tunnel-group DefaultRAGroup general-attributes
    address-pool vpn_pool
    default-group-policy remote_vpn_policy
    tunnel-group DefaultRAGroup ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group DefaultRAGroup ppp-attributes
    authentication ms-chap-v2
    tunnel-group S1.S1.S1.S1 type ipsec-l2l
    tunnel-group S1.S1.S1.S1 general-attributes
    default-group-policy GroupPolicy_S1.S1.S1.S1
    tunnel-group S1.S1.S1.S1 ipsec-attributes
    ikev1 pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:f55f10c19a0848edd2466d08744556eb
    : end

    Thanks for helping me again. I really appreciate.
    I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
    Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
    Because on Cisco ASA I guess I have everything.
    Here is show crypto session detail
    router(config)#do show crypto session detail
    Crypto session current status
    Code: C - IKE Configuration mode, D - Dead Peer Detection
    K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
    X - IKE Extended Authentication, F - IKE Fragmentation
    Interface: GigabitEthernet0/0
    Session status: DOWN
    Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
          Desc: (none)
          Phase1_id: (none)
      IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
            Active SAs: 0, origin: crypto map
            Inbound:  #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
            Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
    Should I see something in crypto isakmp sa?
    pp-border#sh crypto isakmp sa
    IPv4 Crypto ISAKMP SA
    dst             src             state          conn-id status
    IPv6 Crypto ISAKMP SA
    Thanks again for your help.

Maybe you are looking for

  • What does it mean to be "thread safe"?

    What does it mean to be "thread safe"? I am working with a team on a project here at work. Someone here suggested that we build all of our screens during the initialization of the application to save time later. During the use of the application, the

  • Happy Birthday Spotter!

    A Mr S Potter formerly of GD is celebrating a birthday today Bring on the bewb cakes!

  • BEA error: deleteTaskAttributes(int,java.util.Map)

    Hello, I have installed OIM 9100 on BEA with an Oracle Database. I got the following error message after starting OIM: <08.07.2008 11.07 Uhr CEST> <Warning> <EJB> <BEA-012034> <The Remote interface method: 'public abstract void com.thortec h.xl.sched

  • Opening href in the same portlet.

    Scenario: Portlet points to the search.aspx page which collects search parameters to perform a user search. The aspx page postback to itself and posts the response on the same portlet as list of users with their names as hrefs. When you click the hre

  • I am unable to forward emails using the filter

    I have set up a filter to move a specific type of email into another folder, and also to forward that email to another email account. It will copy the email to the folder but every time it fails on forwarding. I have tried 'match all', match any', lo