Cisco ASA 5505 site to site IPSec VPN with RV220W issue
I have a ASA5505 connected to RV220W through IPSec VPN. When using SMB to transfer large file, the ASA5505 will show error message:
CTM ERROR: Invalid input parameters, ctm_get_scb_prot_stats:1561
The error message from the debug crypto engine. When the message show, the speed of the transfer will slow down quickly, and even no data can be go through between ASA and the RV220W. But the IPSec SA and the IKE SA is active, and can ping the inside network in both site.
Both ASA5505 and the RV220W has been updated the latest firmware. I have surf the Google but no such related issue found.
Any suggestions on where to look would be much appreciated.
Thanks in advance
Terry
Hi Ted thanks for your reply and information.
The strange things happened in RV220W shows the IPSec sa is expired, but the ASA5505 IPSec and IKEv1 sa is active. Inside both site internal network can ping to other side, but cant transfer file through Windows SMB. It seems when I transfer over 4GBytes of file, it will start happening and required clear IPSec and IKEv1 sa so that the VPN tunnel will start up again.
I am already surrander for this issue......
Similar Messages
-
Need urgent help in configuring Client to Site IPSec VPN with Hairpinning on Cisco ASA5510 - 8.2(1).
The following is the Layout:
There are two Leased Lines for Internet access - 1.1.1.1 & 2.2.2.2, the latter being the Standard Default route, the former one is for backup.
I have been able to configure Client to Site IPSec VPN
1) With access from Outside to only the Internal Network (172.16.0.0/24) behind the asa
2) With Split tunnel with simultaneous assess to internal LAN and Outside Internet.
But I have not been able to make tradiotional Hairpinng model work in this scenario.
I followed every possible sugestions made in this regard in many Discussion Topics but still no luck. Can someone please help me out here???
Following is the Running-Conf with Normal Client to Site IPSec VPN configured with No internat Access:
LIMITATION: Can't Boot into any other ios image for some unavoidable reason, must use 8.2(1)
running-conf --- Working normal Client to Site VPN without internet access/split tunnel
ASA Version 8.2(1)
hostname ciscoasa
domain-name cisco.campus.com
enable password xxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
names
interface GigabitEthernet0/0
nameif internet1-outside
security-level 0
ip address 1.1.1.1 255.255.255.240
interface GigabitEthernet0/1
nameif internet2-outside
security-level 0
ip address 2.2.2.2 255.255.255.224
interface GigabitEthernet0/2
nameif dmz-interface
security-level 0
ip address 10.0.1.1 255.255.255.0
interface GigabitEthernet0/3
nameif campus-lan
security-level 0
ip address 172.16.0.1 255.255.0.0
interface Management0/0
nameif CSC-MGMT
security-level 100
ip address 10.0.0.4 255.255.255.0
boot system disk0:/asa821-k8.bin
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name cisco.campus.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network cmps-lan
object-group network csc-ip
object-group network www-inside
object-group network www-outside
object-group service tcp-80
object-group service udp-53
object-group service https
object-group service pop3
object-group service smtp
object-group service tcp80
object-group service http-s
object-group service pop3-110
object-group service smtp25
object-group service udp53
object-group service ssh
object-group service tcp-port
object-group service udp-port
object-group service ftp
object-group service ftp-data
object-group network csc1-ip
object-group service all-tcp-udp
access-list INTERNET1-IN extended permit ip host 1.2.2.2 host 2.2.2.3
access-list CSC-OUT extended permit ip host 10.0.0.5 any
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq www
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq https
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ssh
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ftp
access-list CAMPUS-LAN extended permit udp 172.16.0.0 255.255.0.0 any eq domain
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq smtp
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq pop3
access-list CAMPUS-LAN extended permit ip any any
access-list csc-acl remark scan web and mail traffic
access-list csc-acl extended permit tcp any any eq smtp
access-list csc-acl extended permit tcp any any eq pop3
access-list csc-acl remark scan web and mail traffic
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 993
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq imap4
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 465
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq www
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq https
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq smtp
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq pop3
access-list INTERNET2-IN extended permit ip any host 1.1.1.2
access-list nonat extended permit ip 172.16.0.0 255.255.0.0 172.16.0.0 255.255.0.0
access-list DNS-inspect extended permit tcp any any eq domain
access-list DNS-inspect extended permit udp any any eq domain
access-list capin extended permit ip host 172.16.1.234 any
access-list capin extended permit ip host 172.16.1.52 any
access-list capin extended permit ip any host 172.16.1.52
access-list capin extended permit ip host 172.16.0.82 host 172.16.0.61
access-list capin extended permit ip host 172.16.0.61 host 172.16.0.82
access-list capout extended permit ip host 2.2.2.2 any
access-list capout extended permit ip any host 2.2.2.2
access-list campus-lan_nat0_outbound extended permit ip 172.16.0.0 255.255.0.0 192.168.150.0 255.255.255.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu internet1-outside 1500
mtu internet2-outside 1500
mtu dmz-interface 1500
mtu campus-lan 1500
mtu CSC-MGMT 1500
ip local pool vpnpool1 192.168.150.2-192.168.150.250 mask 255.255.255.0
ip verify reverse-path interface internet2-outside
ip verify reverse-path interface dmz-interface
ip verify reverse-path interface campus-lan
ip verify reverse-path interface CSC-MGMT
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (internet1-outside) 1 interface
global (internet2-outside) 1 interface
nat (campus-lan) 0 access-list campus-lan_nat0_outbound
nat (campus-lan) 1 0.0.0.0 0.0.0.0
nat (CSC-MGMT) 1 10.0.0.5 255.255.255.255
static (CSC-MGMT,internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255
access-group INTERNET2-IN in interface internet1-outside
access-group INTERNET1-IN in interface internet2-outside
access-group CAMPUS-LAN in interface campus-lan
access-group CSC-OUT in interface CSC-MGMT
route internet2-outside 0.0.0.0 0.0.0.0 2.2.2.5 1
route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 10.0.0.2 255.255.255.255 CSC-MGMT
http 10.0.0.8 255.255.255.255 CSC-MGMT
http 1.2.2.2 255.255.255.255 internet2-outside
http 1.2.2.2 255.255.255.255 internet1-outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map internet2-outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map internet2-outside_map interface internet2-outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as
quit
crypto isakmp enable internet2-outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash md5
group 2
lifetime 86400
telnet 10.0.0.2 255.255.255.255 CSC-MGMT
telnet 10.0.0.8 255.255.255.255 CSC-MGMT
telnet timeout 5
ssh 1.2.3.3 255.255.255.240 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet2-outside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy VPN_TG_1 internal
group-policy VPN_TG_1 attributes
vpn-tunnel-protocol IPSec
username ssochelpdesk password xxxxxxxxxxxxxx encrypted privilege 15
username administrator password xxxxxxxxxxxxxx encrypted privilege 15
username vpnuser1 password xxxxxxxxxxxxxx encrypted privilege 0
username vpnuser1 attributes
vpn-group-policy VPN_TG_1
tunnel-group VPN_TG_1 type remote-access
tunnel-group VPN_TG_1 general-attributes
address-pool vpnpool1
default-group-policy VPN_TG_1
tunnel-group VPN_TG_1 ipsec-attributes
pre-shared-key *
class-map cmap-DNS
match access-list DNS-inspect
class-map csc-class
match access-list csc-acl
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class csc-class
csc fail-open
class cmap-DNS
inspect dns preset_dns_map
service-policy global_policy global
prompt hostname context
Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y
: end
Neither Adding dynamic NAT for 192.168.150.0/24 on outside interface works, nor does the sysopt connection permit-vpn works
Please tell what needs to be done here, to hairpin all the traffic to internet comming from VPN Clients.
That is I need clients conected via VPN tunnel, when connected to internet, should have their IP's NAT'ted against the internet2-outside interface address 2.2.2.2, as it happens for the Campus Clients (172.16.0.0/16)
I'm not much conversant with everything involved in here, therefore please be elaborative in your replies. Please let me know if you need any more information regarding this setup to answer my query.
Thanks & Regards
maxsHi Jouni,
Thanks again for your help, got it working. Actually the problem was ASA needed some time after configuring to work properly ( ?????? ). I configured and tested several times within a short period, during the day and was not working initially, GUI packet tracer was showing some problems (IPSEC Spoof detected) and also there was this left out dns. Its working fine now.
But my problem is not solved fully here.
Does hairpinning model allow access to the campus LAN behind ASA also?. Coz the setup is working now as i needed, and I can access Internet with the NAT'ed ip address (outside-interface). So far so good. But now I cannot access the Campus LAN behind the asa.
Here the packet tracer output for the traffic:
packet-tracer output
asa# packet-tracer input internet2-outside tcp 192.168.150.1 56482 172.16.1.249 22
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 172.16.0.0 255.255.0.0 campus-lan
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.150.1 255.255.255.255 internet2-outside
Phase: 5
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group internnet1-in in interface internet2-outside
access-list internnet1-in extended permit ip 192.168.150.0 255.255.255.0 any
Additional Information:
Phase: 6
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype:
Result: DROP
Config:
nat (internet2-outside) 1 192.168.150.0 255.255.255.0
match ip internet2-outside 192.168.150.0 255.255.255.0 campus-lan any
dynamic translation to pool 1 (No matching global)
translate_hits = 14, untranslate_hits = 0
Additional Information:
Result:
input-interface: internet2-outside
input-status: up
input-line-status: up
output-interface: internet2-outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
The problem here as you can see is the Rule for dynamic nat that I added to make hairpin work at first place
dynamic nat
asa(config)#nat (internet2-outside) 1 192.168.150.0 255.255.255.0
Is it possible to access both
1)LAN behind ASA
2)INTERNET via HAIRPINNING
simultaneously via a single tunnel-group?
If it can be done, how do I do it. What changes do I need to make here to get simultaneous access to my LAN also?
Thanks & Regards
Abhijit -
Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall
Hi,
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
3
Nov 21 2012
07:11:09
713061
Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5
Nov 21 2012
07:11:09
713119
Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
Here is from the syntax: show crypto isakmp sa
Result of the command: "show crypto isakmp sa"
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 195.149.180.254
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
current_peer:195.149.180.254
#pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
#pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: E715B315
inbound esp sas:
spi: 0xFAC769EB (4207372779)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38738/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xE715B315 (3876958997)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38673/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
And here are my Accesslists and vpn site to site config:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 84600
crypto isakmp nat-traversal 40
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map CustomerCryptoMap 10 match address VPN_Tunnel
crypto map CustomerCryptoMap 10 set pfs group5
crypto map CustomerCryptoMap 10 set peer 195.149.180.254
crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
crypto map CustomerCryptoMap interface outside
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
nat (inside) 0 access-list nonat
All these remote networks are at the Main Site Clavister Firewall.
Best Regards
MichaelHi,
I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
Maybe you could try to change the Encryption Domain configurations a bit and test it then.
You could also maybe take some debugs on the Phase2 and see if you get anymore hints as to what could be the problem when only one network is working for the L2L VPN.
- Jouni -
Cisco ASA 5505 Site to Site VPN
Hello All,
First time posting to the forums. I've been working with Cisco ASA 5505 for a number of months and recently I purchased a 2nd ASA with the goal of setting up Site to Site VPN tunnel. It look so simple from the number of videos that I have watched on the internet. But when I have done it suprise suprise it didn't work for me ... I have deleted the tunnels a number of times and attempted to recreate them. I am using the VPN wizard in the ADM to create the tunnel. Both the asa are 5505 and have the same same firmware etc.
I would appreciate any help that can be directed towards this issue please. Slowly losing my mind
Please see details below:
Both ADM are 7.1
IOS
ASA 1
aved
ASA Version 9.0(1)
hostname PAYBACK
enable password HSMurh79NVmatjY0 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
ip local pool VPN1 192.168.50.1-192.168.50.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
description Trunk link to SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan2
nameif outside
security-level 0
ip address 92.51.193.158 255.255.255.252
interface Vlan10
nameif inside
security-level 100
ip address 192.168.10.1 255.255.255.0
interface Vlan20
nameif servers
security-level 100
ip address 192.168.20.1 255.255.255.0
interface Vlan30
nameif printers
security-level 100
ip address 192.168.30.1 255.255.255.0
interface Vlan40
nameif wireless
security-level 100
ip address 192.168.40.1 255.255.255.0
banner login line Welcome to Payback Loyalty Systems
boot system disk0:/asa901-k8.bin
ftp mode passive
clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
dns domain-lookup outside
dns domain-lookup inside
dns domain-lookup servers
dns domain-lookup printers
dns domain-lookup wireless
dns server-group DefaultDNS
name-server 83.147.160.2
name-server 83.147.160.130
same-security-traffic permit inter-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network ftp_server
object network Internal_Report_Server
host 192.168.20.21
description Automated Report Server Internal Address
object network Report_Server
host 89.234.126.9
description Automated Report Server
object service RDP
service tcp destination eq 3389
description RDP to Server
object network Host_QA_Server
host 89.234.126.10
description QA Host External Address
object network Internal_Host_QA
host 192.168.20.22
description Host of VM machine for QA
object network Internal_QA_Web_Server
host 192.168.20.23
description Web Server in QA environment
object network Web_Server_QA_VM
host 89.234.126.11
description Web server in QA environment
object service SQL_Server
service tcp destination eq 1433
object network Demo_Server
host 89.234.126.12
description Server set up to Demo Product
object network Internal_Demo_Server
host 192.168.20.24
description Internal IP Address of Demo Server
object network NETWORK_OBJ_192.168.20.0_24
subnet 192.168.20.0 255.255.255.0
object network NETWORK_OBJ_192.168.50.0_26
subnet 192.168.50.0 255.255.255.192
object network NETWORK_OBJ_192.168.0.0_16
subnet 192.168.0.0 255.255.0.0
object service MSSQL
service tcp destination eq 1434
description MSSQL port
object network VPN-network
subnet 192.168.50.0 255.255.255.0
object network NETWORK_OBJ_192.168.50.0_24
subnet 192.168.50.0 255.255.255.0
object service TS
service tcp destination eq 4400
object service TS_Return
service tcp source eq 4400
object network External_QA_3
host 89.234.126.13
object network Internal_QA_3
host 192.168.20.25
object network Dev_WebServer
host 192.168.20.27
object network External_Dev_Web
host 89.234.126.14
object network CIX_Subnet
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.10.0_24
subnet 192.168.10.0 255.255.255.0
object network NETWORK_OBJ_84.39.233.50
host 84.39.233.50
object network NETWORK_OBJ_92.51.193.158
host 92.51.193.158
object network NETWORK_OBJ_192.168.100.0_24
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq ftp
service-object tcp destination eq netbios-ssn
service-object tcp destination eq smtp
service-object object TS
object-group network Payback_Internal
network-object 192.168.10.0 255.255.255.0
network-object 192.168.20.0 255.255.255.0
network-object 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
service-object tcp destination eq www
service-object tcp destination eq https
service-object object TS
service-object object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object object RDP
service-object tcp destination eq www
service-object tcp destination eq https
object-group service DM_INLINE_SERVICE_5
service-object object MSSQL
service-object object RDP
service-object object TS
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service DM_INLINE_SERVICE_6
service-object object TS
service-object object TS_Return
service-object tcp destination eq www
service-object tcp destination eq https
access-list outside_access_in remark This rule is allowing from internet to interal server.
access-list outside_access_in remark Allowed:
access-list outside_access_in remark FTP
access-list outside_access_in remark RDP
access-list outside_access_in remark SMTP
access-list outside_access_in remark Net Bios
access-list outside_access_in remark SQL
access-list outside_access_in remark TS - 4400
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any4 object Internal_Report_Server
access-list outside_access_in remark Access rule to internal host QA
access-list outside_access_in remark Allowed:
access-list outside_access_in remark HTTP
access-list outside_access_in remark RDP
access-list outside_access_in extended permit tcp any4 object Internal_Host_QA eq www
access-list outside_access_in remark Access to INternal Web Server:
access-list outside_access_in remark Allowed:
access-list outside_access_in remark HTTP
access-list outside_access_in remark RDP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 any4 object Internal_QA_Web_Server
access-list outside_access_in remark Rule for allowing access to Demo server
access-list outside_access_in remark Allowed:
access-list outside_access_in remark RDP
access-list outside_access_in remark MSSQL
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any4 object Internal_Demo_Server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
access-list outside_access_in remark Access for Development WebServer
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
access-list Payback_VPN_splitTunnelAcl standard permit 192.168.20.0 255.255.255.0
access-list outside_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging console informational
logging asdm informational
logging from-address
[email protected]
logging recipient-address
[email protected]
level alerts
mtu outside 1500
mtu inside 1500
mtu servers 1500
mtu printers 1500
mtu wireless 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711-52.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source dynamic any interface
nat (wireless,outside) source dynamic any interface
nat (servers,outside) source dynamic any interface
nat (servers,outside) source static Internal_Report_Server Report_Server
nat (servers,outside) source static Internal_Host_QA Host_QA_Server
nat (servers,outside) source static Internal_QA_Web_Server Web_Server_QA_VM
nat (servers,outside) source static Internal_Demo_Server Demo_Server
nat (servers,outside) source static NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 destination static NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 no-proxy-arp route-lookup
nat (servers,outside) source static Internal_QA_3 External_QA_3
nat (servers,outside) source static Dev_WebServer External_Dev_Web
nat (inside,outside) source static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 84.39.233.50
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 77.75.100.208 255.255.255.240 outside
ssh 192.168.10.0 255.255.255.0 inside
ssh 192.168.40.0 255.255.255.0 wireless
ssh timeout 5
console timeout 0
dhcpd dns 192.168.0.1
dhcpd auto_config outside
dhcpd address 192.168.10.21-192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
dhcpd option 15 ascii paybackloyalty.com interface inside
dhcpd enable inside
dhcpd address 192.168.40.21-192.168.40.240 wireless
dhcpd dns 192.168.20.21 83.147.160.2 interface wireless
dhcpd update dns interface wireless
dhcpd option 15 ascii paybackloyalty.com interface wireless
dhcpd enable wireless
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy Payback_VPN internal
group-policy Payback_VPN attributes
vpn-simultaneous-logins 10
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Payback_VPN_splitTunnelAcl
group-policy DfltGrpPolicy attributes
dns-server value 83.147.160.2 83.147.160.130
vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
group-policy GroupPolicy_84.39.233.50 internal
group-policy GroupPolicy_84.39.233.50 attributes
vpn-tunnel-protocol ikev1 ikev2
username Noelle password XB/IpvYaATP.2QYm encrypted
username Noelle attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Eanna password vXILR9ZZQIsd1Naw encrypted privilege 0
username Eanna attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Michael password qpbleUqUEchRrgQX encrypted
username Michael attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Danny password .7fEXdzESUk6S/cC encrypted privilege 0
username Danny attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Aileen password tytrelqvV5VRX2pz encrypted privilege 0
username Aileen attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Aidan password aDu6YH0V5XaxpEPg encrypted privilege 0
username Aidan attributes
vpn-group-policy Payback_VPN
service-type remote-access
username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
username shane.c password iqGMoWOnfO6YKXbw encrypted
username shane.c attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Shane password uYePLcrFadO9pBZx encrypted
username Shane attributes
vpn-group-policy Payback_VPN
service-type remote-access
username James password TdYPv1pvld/hPM0d encrypted
username James attributes
vpn-group-policy Payback_VPN
service-type remote-access
username mark password yruxpddqfyNb.qFn encrypted
username mark attributes
service-type admin
username Mary password XND5FTEiyu1L1zFD encrypted
username Mary attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Massimo password vs65MMo4rM0l4rVu encrypted privilege 0
username Massimo attributes
vpn-group-policy Payback_VPN
service-type remote-access
tunnel-group Payback_VPN type remote-access
tunnel-group Payback_VPN general-attributes
address-pool VPN1
default-group-policy Payback_VPN
tunnel-group Payback_VPN ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 general-attributes
default-group-policy GroupPolicy_84.39.233.50
tunnel-group 84.39.233.50 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map global-class
match default-inspection-traffic
policy-map global-policy
class global-class
inspect dns
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect pptp
inspect rsh
inspect rtsp
inspect sip
inspect snmp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect xdmcp
inspect icmp error
inspect icmp
service-policy global-policy global
smtp-server 192.168.20.21
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1
ASA 2
ASA Version 9.0(1)
hostname Payback-CIX
enable password HSMurh79NVmatjY0 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
description This port connects to VLAN 100
switchport access vlan 100
interface Ethernet0/2
interface Ethernet0/3
switchport access vlan 100
interface Ethernet0/4
switchport access vlan 100
interface Ethernet0/5
switchport access vlan 100
interface Ethernet0/6
switchport access vlan 100
interface Ethernet0/7
switchport access vlan 100
interface Vlan2
nameif outside
security-level 0
ip address 84.39.233.50 255.255.255.240
interface Vlan100
nameif inside
security-level 100
ip address 192.168.100.1 255.255.255.0
banner login line Welcome to Payback Loyalty - CIX
ftp mode passive
clock summer-time gmt/idt recurring last Sun Mar 1:00 last Sun Oct 2:00
dns domain-lookup outside
dns domain-lookup inside
dns server-group defaultDNS
name-server 8.8.8.8
name-server 8.8.4.4
same-security-traffic permit inter-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network CIX-Host-1
host 192.168.100.2
description This is the host machine of the VM servers
object network External_CIX-Host-1
host 84.39.233.51
description This is the external IP address of the host server for the VM server
object service RDP
service tcp source range 1 65535 destination eq 3389
object network Payback_Office
host 92.51.193.158
object service MSQL
service tcp destination eq 1433
object network Development_OLTP
host 192.168.100.10
description VM for Eiresoft
object network External_Development_OLTP
host 84.39.233.52
description This is the external IP address for the VM for Eiresoft
object network Eiresoft
host 146.66.160.70
description DBA Contractor
object network External_TMC_Web
host 84.39.233.53
description Public Address of TMC Webserver
object network TMC_Webserver
host 192.168.100.19
description Internal Address of TMC Webserver
object network External_TMC_OLTP
host 84.39.233.54
description Targets OLTP external IP
object network TMC_OLTP
host 192.168.100.18
description Targets interal IP address
object network External_OLTP_Failover
host 84.39.233.55
description Public IP of OLTP Failover
object network OLTP_Failover
host 192.168.100.60
description Server for OLTP failover
object network Servers
subnet 192.168.20.0 255.255.255.0
object network Wired
subnet 192.168.10.0 255.255.255.0
object network Wireless
subnet 192.168.40.0 255.255.255.0
object network NETWORK_OBJ_192.168.100.0_24
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.10.0_24
subnet 192.168.10.0 255.255.255.0
object network Eiresoft_2nd
host 137.117.217.29
description Eiresoft 2nd IP
object network Dev_Test_Webserver
host 192.168.100.12
description Dev Test Webserver Internal Address
object network External_Dev_Test_Webserver
host 84.39.233.56
description This is the PB Dev Test Webserver
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_2
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_3
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_4
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_5
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_6
service-object object MSQL
service-object object RDP
object-group network Payback_Intrernal
network-object object Servers
network-object object Wired
network-object object Wireless
object-group service DM_INLINE_SERVICE_7
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_8
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_9
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_10
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_11
service-object object RDP
service-object tcp destination eq ftp
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-Host-1
access-list outside_access_in remark Development OLTP from Payback Office
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP
access-list outside_access_in remark Access for Eiresoft
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver
access-list outside_access_in remark Access to OLTP for target from Payback Office
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover
access-list outside_access_in remark This is allowing access from Eiresoft to the OLTP Failover server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover
access-list outside_access_in remark Access for the 2nd IP from Eiresoft
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP
access-list outside_access_in remark Access from the 2nd Eiresoft IP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP
access-list outside_cryptomap extended permit ip 192.168.100.0 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source dynamic any interface
nat (inside,outside) source static CIX-Host-1 External_CIX-Host-1
nat (inside,outside) source static Development_OLTP External_Development_OLTP
nat (inside,outside) source static TMC_Webserver External_TMC_Web
nat (inside,outside) source static TMC_OLTP External_TMC_OLTP
nat (inside,outside) source static OLTP_Failover External_OLTP_Failover
nat (inside,outside) source static Dev_Test_Webserver External_Dev_Test_Webserver
nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 92.51.193.156 255.255.255.252 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 92.51.193.158
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 77.75.100.208 255.255.255.240 outside
ssh 92.51.193.156 255.255.255.252 outside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy GroupPolicy_92.51.193.158 internal
group-policy GroupPolicy_92.51.193.158 attributes
vpn-tunnel-protocol ikev1 ikev2
username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 general-attributes
default-group-policy GroupPolicy_92.51.193.158
tunnel-group 92.51.193.158 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHi,
Thanks for the help to date
I now have the Site to Site working but there is one little issue I have. If I try to RD to a server through the tunnel it will not allow connection on the first attempt however if I ping that host and then attempt to RD it will allow the connection. It looks like the host is asleep until it receives traffic through the tunnel. Is this thje correct behaviour.
See below the details:
ASA1:
hostname PAYBACK
enable password HSMurh79NVmatjY0 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
ip local pool VPN1 192.168.50.1-192.168.50.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
description Trunk link to SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan2
nameif outside
security-level 0
ip address XX.XX.XX.XX 255.255.255.252
interface Vlan10
nameif inside
security-level 100
ip address 192.168.10.1 255.255.255.0
interface Vlan20
nameif servers
security-level 100
ip address 192.168.20.1 255.255.255.0
interface Vlan30
nameif printers
security-level 100
ip address 192.168.30.1 255.255.255.0
interface Vlan40
nameif wireless
security-level 100
ip address 192.168.40.1 255.255.255.0
banner login line Welcome to Payback Loyalty Systems
boot system disk0:/asa901-k8.bin
ftp mode passive
clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
dns domain-lookup outside
dns domain-lookup inside
dns domain-lookup servers
dns domain-lookup printers
dns domain-lookup wireless
dns server-group DefaultDNS
name-server 83.147.160.2
name-server 83.147.160.130
same-security-traffic permit inter-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network ftp_server
object network Internal_Report_Server
host 192.168.20.21
description Automated Report Server Internal Address
object network Report_Server
host 89.234.126.9
description Automated Report Server
object service RDP
service tcp destination eq 3389
description RDP to Server
object network Host_QA_Server
host 89.234.126.10
description QA Host External Address
object network Internal_Host_QA
host 192.168.20.22
description Host of VM machine for QA
object network Internal_QA_Web_Server
host 192.168.20.23
description Web Server in QA environment
object network Web_Server_QA_VM
host 89.234.126.11
description Web server in QA environment
object service SQL_Server
service tcp destination eq 1433
object network Demo_Server
host 89.234.126.12
description Server set up to Demo Product
object network Internal_Demo_Server
host 192.168.20.24
description Internal IP Address of Demo Server
object network NETWORK_OBJ_192.168.20.0_24
subnet 192.168.20.0 255.255.255.0
object network NETWORK_OBJ_192.168.50.0_26
subnet 192.168.50.0 255.255.255.192
object network NETWORK_OBJ_192.168.0.0_16
subnet 192.168.0.0 255.255.0.0
object service MSSQL
service tcp destination eq 1434
description MSSQL port
object network VPN-network
subnet 192.168.50.0 255.255.255.0
object network NETWORK_OBJ_192.168.50.0_24
subnet 192.168.50.0 255.255.255.0
object service TS
service tcp destination eq 4400
object service TS_Return
service tcp source eq 4400
object network External_QA_3
host 89.234.126.13
object network Internal_QA_3
host 192.168.20.25
object network Dev_WebServer
host 192.168.20.27
object network External_Dev_Web
host 89.234.126.14
object network NETWORK_OBJ_192.168.100.0_24
subnet 192.168.100.0 255.255.255.0
object network Wireless
subnet 192.168.40.0 255.255.255.0
description Wireless network
object network Servers
subnet 192.168.20.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq ftp
service-object tcp destination eq netbios-ssn
service-object tcp destination eq smtp
service-object object TS
service-object object SQL_Server
object-group service DM_INLINE_SERVICE_3
service-object tcp destination eq www
service-object tcp destination eq https
service-object object TS
service-object object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object object RDP
service-object tcp destination eq www
service-object tcp destination eq https
object-group service DM_INLINE_SERVICE_5
service-object object MSSQL
service-object object RDP
service-object object TS
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service DM_INLINE_SERVICE_6
service-object object TS
service-object object TS_Return
service-object tcp destination eq www
service-object tcp destination eq https
object-group network DM_INLINE_NETWORK_1
network-object 192.168.10.0 255.255.255.0
network-object 192.168.20.0 255.255.255.0
network-object 192.168.40.0 255.255.255.0
object-group network Payback_Internal
network-object 192.168.10.0 255.255.255.0
network-object 192.168.20.0 255.255.255.0
network-object 192.168.40.0 255.255.255.0
access-list outside_access_in remark This rule is allowing from internet to interal server.
access-list outside_access_in remark Allowed:
access-list outside_access_in remark FTP
access-list outside_access_in remark RDP
access-list outside_access_in remark SMTP
access-list outside_access_in remark Net Bios
access-list outside_access_in remark SQL
access-list outside_access_in remark TS - 4400
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any4 object Internal_Report_Server
access-list outside_access_in remark Access rule to internal host QA
access-list outside_access_in remark Allowed:
access-list outside_access_in remark HTTP
access-list outside_access_in remark RDP
access-list outside_access_in extended permit tcp any4 object Internal_Host_QA eq www
access-list outside_access_in remark Access to INternal Web Server:
access-list outside_access_in remark Allowed:
access-list outside_access_in remark HTTP
access-list outside_access_in remark RDP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 any4 object Internal_QA_Web_Server
access-list outside_access_in remark Rule for allowing access to Demo server
access-list outside_access_in remark Allowed:
access-list outside_access_in remark RDP
access-list outside_access_in remark MSSQL
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any4 object Internal_Demo_Server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
access-list outside_access_in remark Access for Development WebServer
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
access-list Payback_VPN_splitTunnelAcl standard permit 192.168.20.0 255.255.255.0
access-list outside_cryptomap extended permit ip object-group DM_INLINE_NETWORK_1 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging console informational
logging asdm informational
logging from-address [email protected]
logging recipient-address [email protected] level alerts
mtu outside 1500
mtu inside 1500
mtu servers 1500
mtu printers 1500
mtu wireless 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711-52.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
nat (wireless,outside) source static Wireless Wireless destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
nat (servers,outside) source static Servers Servers destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
nat (inside,outside) source dynamic any interface
nat (wireless,outside) source dynamic any interface
nat (servers,outside) source dynamic any interface
nat (servers,outside) source static Internal_Report_Server Report_Server
nat (servers,outside) source static Internal_Host_QA Host_QA_Server
nat (servers,outside) source static Internal_QA_Web_Server Web_Server_QA_VM
nat (servers,outside) source static Internal_Demo_Server Demo_Server
nat (servers,outside) source static NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 destination static NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 no-proxy-arp route-lookup
nat (servers,outside) source static Internal_QA_3 External_QA_3
nat (servers,outside) source static Dev_WebServer External_Dev_Web
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.10.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer XX.XX.XX.XX
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map servers_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map servers_map interface servers
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev2 enable inside client-services port 443
crypto ikev1 enable outside
crypto ikev1 enable inside
crypto ikev1 enable servers
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.10.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd dns 192.168.0.1
dhcpd auto_config outside
dhcpd address 192.168.10.21-192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
dhcpd option 15 ascii paybackloyalty.com interface inside
dhcpd enable inside
dhcpd address 192.168.40.21-192.168.40.240 wireless
dhcpd dns 192.168.20.21 83.147.160.2 interface wireless
dhcpd update dns interface wireless
dhcpd option 15 ascii paybackloyalty.com interface wireless
dhcpd enable wireless
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy Payback_VPN internal
group-policy Payback_VPN attributes
vpn-simultaneous-logins 10
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Payback_VPN_splitTunnelAcl
group-policy DfltGrpPolicy attributes
dns-server value 83.147.160.2 83.147.160.130
vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
group-policy GroupPolicy_84.39.233.50 internal
group-policy GroupPolicy_84.39.233.50 attributes
vpn-tunnel-protocol ikev1 ikev2
username Noelle password XB/IpvYaATP.2QYm encrypted
username Noelle attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Eanna password vXILR9ZZQIsd1Naw encrypted privilege 0
username Eanna attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Michael password qpbleUqUEchRrgQX encrypted
username Michael attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Danny password .7fEXdzESUk6S/cC encrypted privilege 0
username Danny attributes
vpn-group-policy Payback_VPN
service-type remote-access
username niamh password MlFlIlEiy8vismE0 encrypted
username niamh attributes
service-type admin
username Aileen password tytrelqvV5VRX2pz encrypted privilege 0
username Aileen attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Aidan password aDu6YH0V5XaxpEPg encrypted privilege 0
username Aidan attributes
vpn-group-policy Payback_VPN
service-type remote-access
username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
username shane.c password iqGMoWOnfO6YKXbw encrypted
username shane.c attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Shane password yQeVtvLLKqapoUje encrypted privilege 0
username Shane attributes
vpn-group-policy Payback_VPN
service-type remote-access
username James password TdYPv1pvld/hPM0d encrypted
username James attributes
vpn-group-policy Payback_VPN
service-type remote-access
username mark password yruxpddqfyNb.qFn encrypted
username mark attributes
service-type admin
username Mary password XND5FTEiyu1L1zFD encrypted
username Mary attributes
vpn-group-policy Payback_VPN
service-type remote-access
username Massimo password vs65MMo4rM0l4rVu encrypted privilege 0
username Massimo attributes
vpn-group-policy Payback_VPN
service-type remote-access
tunnel-group Payback_VPN type remote-access
tunnel-group Payback_VPN general-attributes
address-pool VPN1
default-group-policy Payback_VPN
tunnel-group Payback_VPN ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 general-attributes
default-group-policy GroupPolicy_84.39.233.50
tunnel-group 84.39.233.50 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map global-class
match default-inspection-traffic
policy-map global-policy
class global-class
inspect dns
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect pptp
inspect rsh
inspect rtsp
inspect sip
inspect snmp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect xdmcp
inspect icmp error
inspect icmp
service-policy global-policy global
smtp-server 192.168.20.21
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:83fa7ce1d93375645205f6e79b526381
ASA2:
ASA Version 9.0(1)
hostname Payback-CIX
enable password HSMurh79NVmatjY0 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
description This port connects to VLAN 100
switchport access vlan 100
interface Ethernet0/2
interface Ethernet0/3
switchport access vlan 100
interface Ethernet0/4
switchport access vlan 100
interface Ethernet0/5
switchport access vlan 100
interface Ethernet0/6
switchport access vlan 100
interface Ethernet0/7
switchport access vlan 100
interface Vlan2
nameif outside
security-level 0
ip address X.X.X.X 255.255.255.240
interface Vlan100
nameif inside
security-level 100
ip address 192.168.100.1 255.255.255.0
banner login line Welcome to Payback Loyalty - CIX
ftp mode passive
clock timezone GMT 0
clock summer-time gmt/idt recurring last Sun Mar 1:00 last Sun Oct 2:00
dns domain-lookup outside
dns domain-lookup inside
dns server-group defaultDNS
name-server 8.8.8.8
name-server 8.8.4.4
same-security-traffic permit inter-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network CIX-Host-1
host 192.168.100.2
description This is the host machine of the VM servers
object network External_CIX-Host-1
host 84.39.233.51
description This is the external IP address of the host server for the VM server
object service RDP
service tcp source range 1 65535 destination eq 3389
object network Payback_Office
host 92.51.193.158
object service MSQL
service tcp destination eq 1433
object network Development_OLTP
host 192.168.100.10
description VM for Eiresoft
object network External_Development_OLTP
host 84.39.233.52
description This is the external IP address for the VM for Eiresoft
object network External_TMC_Web
host 84.39.233.53
description Public Address of TMC Webserver
object network TMC_Webserver
host 192.168.100.19
description Internal Address of TMC Webserver
object network External_TMC_OLTP
host 84.39.233.54
description Targets OLTP external IP
object network TMC_OLTP
host 192.168.100.18
description Targets interal IP address
object network External_OLTP_Failover
host 84.39.233.55
description Public IP of OLTP Failover
object network OLTP_Failover
host 192.168.100.60
description Server for OLTP failover
object network Servers
subnet 192.168.20.0 255.255.255.0
object network Wired
subnet 192.168.10.0 255.255.255.0
object network Wireless
subnet 192.168.40.0 255.255.255.0
object network NETWORK_OBJ_192.168.100.0_24
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.10.0_24
subnet 192.168.10.0 255.255.255.0
object network Eiresoft_2nd
host 137.117.217.29
description Eiresoft 2nd IP
object network Dev_Test_Webserver
host 192.168.100.12
description Dev Test Webserver Internal Address
object network External_Dev_Test_Webserver
host 84.39.233.56
description This is the PB Dev Test Webserver
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network LAN
subnet 192.168.100.0 255.255.255.0
object network REMOTE-LAN
subnet 192.168.10.0 255.255.255.0
object network TargetMC
host 83.71.194.145
description This is Target Location that will be accessing the Webserver
object network Rackspace_OLTP
host 162.13.34.56
description This is the IP address of production OLTP
object service DB
service tcp destination eq 5022
object network Topaz_Target_VM
host 82.198.151.168
description This is Topaz IP that will be accessing Targets VM
object service DB_2
service tcp destination eq 5023
object network EireSoft_NEW_IP
host 146.66.161.3
description Eiresoft latest IP form ISP DHCP
object-group service DM_INLINE_SERVICE_1
service-object object MSQL
service-object object RDP
service-object icmp echo
service-object icmp echo-reply
object-group service DM_INLINE_SERVICE_2
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_4
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
service-object tcp destination eq www
object-group service DM_INLINE_SERVICE_5
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_6
service-object object MSQL
service-object object RDP
object-group network Payback_Intrernal
network-object object Servers
network-object object Wired
network-object object Wireless
object-group service DM_INLINE_SERVICE_8
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_9
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_10
service-object object MSQL
service-object object RDP
service-object tcp destination eq ftp
service-object icmp echo
service-object icmp echo-reply
service-object object DB
object-group service DM_INLINE_SERVICE_11
service-object object RDP
service-object tcp destination eq ftp
object-group service DM_INLINE_SERVICE_12
service-object object MSQL
service-object icmp echo
service-object icmp echo-reply
service-object object DB
service-object object DB_2
object-group service DM_INLINE_SERVICE_13
service-object object MSQL
service-object object RDP
object-group service DM_INLINE_SERVICE_14
service-object object MSQL
service-object object RDP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-Host-1
access-list outside_access_in remark Development OLTP from Payback Office
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver
access-list outside_access_in remark Access to OLTP for target from Payback Office
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover
access-list outside_access_in remark Access for the 2nd IP from Eiresoft
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP
access-list outside_access_in remark Access from the 2nd Eiresoft IP
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP
access-list outside_access_in remark Access rules from Traget to CIX for testing
access-list outside_access_in extended permit tcp object TargetMC object TMC_Webserver eq www
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_12 object Rackspace_OLTP object OLTP_Failover
access-list outside_access_in remark Topaz access to Target VM
access-list outside_access_in extended permit tcp object Topaz_Target_VM object TMC_Webserver eq www
access-list outside_access_in remark Opened up for Target for the weekend. Closing on Monday 20th
access-list outside_access_in extended permit tcp any object TMC_Webserver eq www
access-list outside_access_in remark Access for Eiresoft after their ISP changed their IP Address
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_13 object EireSoft_NEW_IP object Development_OLTP
access-list outside_access_in remark Eiresoft Access after ISP changed their IP Address
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_14 object EireSoft_NEW_IP object OLTP_Failover
access-list outside_cryptomap extended permit ip 192.168.100.0 255.255.255.0 object-group Payback_Intrernal
pager lines 24
logging enable
logging console debugging
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static Payback_Intrernal Payback_Intrernal no-proxy-arp route-lookup
nat (inside,outside) source static CIX-Host-1 External_CIX-Host-1
nat (inside,outside) source static Development_OLTP External_Development_OLTP
nat (inside,outside) source static TMC_Webserver External_TMC_Web
nat (inside,outside) source static TMC_OLTP External_TMC_OLTP
nat (inside,outside) source static OLTP_Failover External_OLTP_Failover
nat (inside,outside) source static Dev_Test_Webserver External_Dev_Test_Webserver
nat (inside,outside) source dynamic LAN interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http X.X.X.X 255.255.255.252 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer X.X.X.X
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh X.X.X.X 255.255.255.240 outside
ssh X.X.X.X 255.255.255.252 outside
ssh 192.168.40.0 255.255.255.0 outside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy GroupPolicy_92.51.193.158 internal
group-policy GroupPolicy_92.51.193.158 attributes
vpn-tunnel-protocol ikev1 ikev2
username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 general-attributes
default-group-policy GroupPolicy_92.51.193.158
tunnel-group 92.51.193.158 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:78a7b9ccec2fa048306092eb29a2b769 -
Cisco ASA 5505 Site to Site VPN Problem
Hi All,
We have a site to site VPN with a cisco asa 5505 on one end and a Checkpoint firewall on the other end.
We can establish the vpn tunnel and all users in the remote office are working great. However at a random point during the day or it may even be after 2 weeks of working, the tunnel between the sites automatically fails.
When I dial into the modem which is connected to the firewall I see the following messages in the logs:
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
There is nothing in the Checkpoint logs. To solve the issue I have to reload the firewall.
I have checked both firewalls for any mis-matched parameters and do not see any.
Any help is very much appreciated as it is very frustrating for myself and the users in the remote office.
Thanks!Also to note, PFS is enabled on both firewalls. Config on Cisco ASA firewall as follows:
hostname
domain-name
enable passwordpasswd names
interface Vlan701
nameif inside
security-level 100
ip address 10.65.0.69 255.255.255.252
interface Vlan999
nameif outside
security-level 0
ip address ****** 255.255.255.248
interface Ethernet0/0
description Link to Internet
switchport access vlan 999
interface Ethernet0/1
description
switchport access vlan 701
interface range Ethernet0/2 - 0/7
switchport access vlan 2
shutdown
ftp mode passive
dns server-group DefaultDNS
domain-name******
access-list 101 extended permit ip host ****** 172.25.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 host ******
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 ******* 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 ******** 255.255.255.0
pager lines 24
logging enable
logging timestamp
logging buffered warnings
logging trap warnings
logging asdm informational
logging host outside *****
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside) 0 access-list nonat
route inside ******
route outside 0.0.0.0 0.0.0.0 ********
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
snmp-server location **:
snmp-server contact **
snmp-server community shortkey
snmp-server enable traps snmp authentication linkup linkdown coldstart
snmp-server enable traps syslog
crypto ipsec transform-set 3desmd5 esp-3des esp-md5-hmac
crypto map CASGMAP 50 match address 101
crypto map CASGMAP 50 set pfs group1
crypto map CASGMAP 50 set peer ********
crypto map CASGMAP 50 set transform-set 3desmd5
crypto map CASGMAP 50 set security-association lifetime seconds 3600
crypto map CASGMAP interface outside
crypto isakmp enable outside
crypto isakmp policy 20
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet **** inside
telnet timeout 5
ssh **** inside
ssh **** outside
ssh timeout 5
console timeout 30
management-access inside
dhcpd ping_timeout 750
priority-queue outside
ntp server **
username ***
tunnel-group ******** type ipsec-l2l
tunnel-group ******** ipsec-attributes
pre-shared-key ***
class-map VoIP
match dscp ef
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map General-purpose
class VoIP
priority
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect http
service-policy General-purpose interface outside
prompt hostname context -
Cisco ASA 5505 site to site Multiple subnet.
Hi. I need some help configuring my cisco asa 5505.
I've set up a VPN tunnel between two ASA 5505
Site 1:
Subnet 192.168.77.0
Site 2:
Have multiple vlans and now the tunnel goes to vlan400 - 192.168.1.0
What I need help with:
From site 1 i need to be able to reach another vlan on site 2. vlan480 - 192.168.20.0
And from site 1 I need to reach 192.168.77.0 subnet from vlan480 - 192.168.20.0
Vlan480 is used for phones. In vlan480 we have a PABX central.
Is this possible to do?
Any help would be greatfully appreciated!
Config site 2:
: Saved
ASA Version 7.2(2)
hostname ciscoasa
domain-name default.domain.invalid
enable password x encrypted
names
name 192.168.1.250 DomeneServer
name 192.168.1.10 NotesServer
name 192.168.1.90 OvServer
name 192.168.1.97 TerminalServer
name 192.168.1.98 w8-eyeshare
name 192.168.50.10 w8-print
name 192.168.1.94 w8-app
name 192.168.1.89 FonnaFlyMedia
interface Vlan1
nameif Vlan1
security-level 100
ip address 192.168.200.100 255.255.255.0
ospf cost 10
interface Vlan2
nameif outside
security-level 0
ip address 79.x.x.226 255.255.255.224
ospf cost 10
interface Vlan400
nameif vlan400
security-level 100
ip address 192.168.1.1 255.255.255.0
ospf cost 10
interface Vlan450
nameif Vlan450
security-level 100
ip address 192.168.210.1 255.255.255.0
ospf cost 10
interface Vlan460
nameif Vlan460-SuldalHotell
security-level 100
ip address 192.168.2.1 255.255.255.0
ospf cost 10
interface Vlan461
nameif Vlan461-SuldalHotellGjest
security-level 100
ip address 192.168.3.1 255.255.255.0
ospf cost 10
interface Vlan462
nameif Vlan462-Suldalsposten
security-level 100
ip address 192.168.4.1 255.255.255.0
ospf cost 10
interface Vlan470
nameif vlan470-Kyrkjekontoret
security-level 100
ip address 192.168.202.1 255.255.255.0
ospf cost 10
interface Vlan480
nameif vlan480-Telefoni
security-level 100
ip address 192.168.20.1 255.255.255.0
ospf cost 10
interface Vlan490
nameif Vlan490-QNapBackup
security-level 100
ip address 192.168.10.1 255.255.255.0
ospf cost 10
interface Vlan500
nameif Vlan500-HellandBadlands
security-level 100
ip address 192.168.30.1 255.255.255.0
ospf cost 10
interface Vlan510
nameif Vlan510-IsTak
security-level 100
ip address 192.168.40.1 255.255.255.0
ospf cost 10
interface Vlan600
nameif Vlan600-SafeQ
security-level 100
ip address 192.168.50.1 255.255.255.0
ospf cost 10
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 500
switchport trunk allowed vlan 400,450,460-462,470,480,500,510,600,610
switchport mode trunk
interface Ethernet0/3
switchport access vlan 490
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd x encrypted
ftp mode passive
clock timezone WAT 1
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group service Lotus_Notes_Utgaaande tcp
description Frim Notes og ut til alle
port-object eq domain
port-object eq ftp
port-object eq www
port-object eq https
port-object eq lotusnotes
port-object eq pop3
port-object eq pptp
port-object eq smtp
object-group service Lotus_Notes_inn tcp
description From alle og inn til Notes
port-object eq www
port-object eq lotusnotes
port-object eq pop3
port-object eq smtp
object-group service Reisebyraa tcp-udp
port-object range 3702 3702
port-object range 5500 5500
port-object range 9876 9876
object-group service Remote_Desktop tcp-udp
description Tilgang til Remote Desktop
port-object range 3389 3389
object-group service Sand_Servicenter_50000 tcp-udp
description Program tilgang til Sand Servicenter AS
port-object range 50000 50000
object-group service VNC_Remote_Admin tcp
description Frå oss til alle
port-object range 5900 5900
object-group service Printer_Accept tcp-udp
port-object range 9100 9100
port-object eq echo
object-group icmp-type Echo_Ping
icmp-object echo
icmp-object echo-reply
object-group service Print tcp
port-object range 9100 9100
object-group service FTP_NADA tcp
description Suldalsposten NADA tilgang
port-object eq ftp
port-object eq ftp-data
object-group service Telefonsentral tcp
description Hoftun
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
port-object eq telnet
object-group service Printer_inn_800 tcp
description Fra 800 nettet og inn til 400 port 7777
port-object range 7777 7777
object-group service Suldalsposten tcp
description Sending av mail vha Mac Mail programmet - åpner smtp
port-object eq pop3
port-object eq smtp
object-group service http2 tcp
port-object range 81 81
object-group service DMZ_FTP_PASSIVE tcp-udp
port-object range 55536 56559
object-group service DMZ_FTP tcp-udp
port-object range 20 21
object-group service DMZ_HTTPS tcp-udp
port-object range 443 443
object-group service DMZ_HTTP tcp-udp
port-object range 8080 8080
object-group service DNS_Query tcp
port-object range domain domain
object-group service DUETT_SQL_PORT tcp-udp
description For kobling mellom andre nett og duett server
port-object range 54659 54659
access-list outside_access_in extended permit ip any any
access-list outside_access_out extended permit ip any any
access-list vlan400_access_in extended deny ip any host 149.20.56.34
access-list vlan400_access_in extended deny ip any host 149.20.56.32
access-list vlan400_access_in extended permit ip any any
access-list Vlan450_access_in extended deny ip any host 149.20.56.34
access-list Vlan450_access_in extended deny ip any host 149.20.56.32
access-list Vlan450_access_in extended permit ip any any
access-list Vlan460_access_in extended deny ip any host 149.20.56.34
access-list Vlan460_access_in extended deny ip any host 149.20.56.32
access-list Vlan460_access_in extended permit ip any any
access-list vlan400_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_Utgaaande
access-list vlan400_access_out extended permit tcp any host DomeneServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host TerminalServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host OvServer object-group http2
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_inn
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host w8-eyeshare object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host w8-app object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host FonnaFlyMedia range 8400 8600
access-list vlan400_access_out extended permit udp any host FonnaFlyMedia range 9000 9001
access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host DomeneServer
access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host w8-app object-group DUETT_SQL_PORT
access-list Vlan500_access_in extended deny ip any host 149.20.56.34
access-list Vlan500_access_in extended deny ip any host 149.20.56.32
access-list Vlan500_access_in extended permit ip any any
access-list vlan470_access_in extended deny ip any host 149.20.56.34
access-list vlan470_access_in extended deny ip any host 149.20.56.32
access-list vlan470_access_in extended permit ip any any
access-list Vlan490_access_in extended deny ip any host 149.20.56.34
access-list Vlan490_access_in extended deny ip any host 149.20.56.32
access-list Vlan490_access_in extended permit ip any any
access-list Vlan450_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan1_access_out extended permit ip any any
access-list Vlan1_access_out extended permit tcp any host w8-print object-group Remote_Desktop
access-list Vlan1_access_out extended deny ip any any
access-list Vlan1_access_out extended permit icmp any any echo-reply
access-list Vlan460_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan490_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP_PASSIVE
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTPS
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTP
access-list Vlan500_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan470_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan470_access_out extended permit tcp any host 192.168.202.10 object-group Remote_Desktop
access-list Vlan510_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan480_access_out extended permit ip any any
access-list Vlan510_access_in extended permit ip any any
access-list Vlan600_access_in extended permit ip any any
access-list Vlan600_access_out extended permit icmp any any
access-list Vlan600_access_out extended permit tcp any host w8-print object-group Remote_Desktop
access-list Vlan600_access_out extended permit tcp 192.168.1.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_out extended permit tcp 192.168.202.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_out extended permit tcp 192.168.210.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_in_1 extended permit ip any any
access-list Vlan461_access_in extended permit ip any any
access-list Vlan461_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan400_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list outside_20_cryptomap_1 extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list outside_20_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list Vlan462-Suldalsposten_access_in extended permit ip any any
access-list Vlan462-Suldalsposten_access_out extended permit icmp any any echo-reply
access-list Vlan462-Suldalsposten_access_out_1 extended permit icmp any any echo-reply
access-list Vlan462-Suldalsposten_access_in_1 extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu Vlan1 1500
mtu outside 1500
mtu vlan400 1500
mtu Vlan450 1500
mtu Vlan460-SuldalHotell 1500
mtu Vlan461-SuldalHotellGjest 1500
mtu vlan470-Kyrkjekontoret 1500
mtu vlan480-Telefoni 1500
mtu Vlan490-QNapBackup 1500
mtu Vlan500-HellandBadlands 1500
mtu Vlan510-IsTak 1500
mtu Vlan600-SafeQ 1500
mtu Vlan462-Suldalsposten 1500
no failover
monitor-interface Vlan1
monitor-interface outside
monitor-interface vlan400
monitor-interface Vlan450
monitor-interface Vlan460-SuldalHotell
monitor-interface Vlan461-SuldalHotellGjest
monitor-interface vlan470-Kyrkjekontoret
monitor-interface vlan480-Telefoni
monitor-interface Vlan490-QNapBackup
monitor-interface Vlan500-HellandBadlands
monitor-interface Vlan510-IsTak
monitor-interface Vlan600-SafeQ
monitor-interface Vlan462-Suldalsposten
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (vlan400) 0 access-list vlan400_nat0_outbound
nat (vlan400) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan450) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan460-SuldalHotell) 1 0.0.0.0 0.0.0.0
nat (Vlan461-SuldalHotellGjest) 1 0.0.0.0 0.0.0.0
nat (vlan470-Kyrkjekontoret) 1 0.0.0.0 0.0.0.0
nat (Vlan490-QNapBackup) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan500-HellandBadlands) 1 0.0.0.0 0.0.0.0
nat (Vlan510-IsTak) 1 0.0.0.0 0.0.0.0
nat (Vlan600-SafeQ) 1 0.0.0.0 0.0.0.0
nat (Vlan462-Suldalsposten) 1 0.0.0.0 0.0.0.0
static (vlan400,outside) 79.x.x.x DomeneServer netmask 255.255.255.255
static (vlan470-Kyrkjekontoret,outside) 79.x.x.x 192.168.202.10 netmask 255.255.255.255
static (vlan400,outside) 79.x.x.x NotesServer netmask 255.255.255.255 dns
static (vlan400,outside) 79.x.x.231 TerminalServer netmask 255.255.255.255
static (vlan400,outside) 79.x.x.234 OvServer netmask 255.255.255.255
static (vlan400,outside) 79.x.x.232 w8-eyeshare netmask 255.255.255.255
static (Vlan490-QNapBackup,outside) 79.x.x.233 192.168.10.10 netmask 255.255.255.255 dns
static (Vlan600-SafeQ,outside) 79.x.x.235 w8-print netmask 255.255.255.255
static (vlan400,outside) 79.x.x.236 w8-app netmask 255.255.255.255
static (Vlan450,vlan400) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (Vlan500-HellandBadlands,vlan400) 192.168.30.0 192.168.30.0 netmask 255.255.255.0
static (vlan400,Vlan500-HellandBadlands) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,Vlan450) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,outside) 79.x.x.252 FonnaFlyMedia netmask 255.255.255.255
static (Vlan462-Suldalsposten,vlan400) 192.168.4.0 192.168.4.0 netmask 255.255.255.0
static (vlan400,Vlan462-Suldalsposten) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,Vlan600-SafeQ) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (Vlan600-SafeQ,vlan400) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ,Vlan450) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ,vlan470-Kyrkjekontoret) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan450,Vlan600-SafeQ) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (vlan470-Kyrkjekontoret,Vlan600-SafeQ) 192.168.202.0 192.168.202.0 netmask 255.255.255.0
access-group Vlan1_access_out out interface Vlan1
access-group outside_access_in in interface outside
access-group outside_access_out out interface outside
access-group vlan400_access_in in interface vlan400
access-group vlan400_access_out out interface vlan400
access-group Vlan450_access_in in interface Vlan450
access-group Vlan450_access_out out interface Vlan450
access-group Vlan460_access_in in interface Vlan460-SuldalHotell
access-group Vlan460_access_out out interface Vlan460-SuldalHotell
access-group Vlan461_access_in in interface Vlan461-SuldalHotellGjest
access-group Vlan461_access_out out interface Vlan461-SuldalHotellGjest
access-group vlan470_access_in in interface vlan470-Kyrkjekontoret
access-group vlan470_access_out out interface vlan470-Kyrkjekontoret
access-group vlan480_access_out out interface vlan480-Telefoni
access-group Vlan490_access_in in interface Vlan490-QNapBackup
access-group Vlan490_access_out out interface Vlan490-QNapBackup
access-group Vlan500_access_in in interface Vlan500-HellandBadlands
access-group Vlan500_access_out out interface Vlan500-HellandBadlands
access-group Vlan510_access_in in interface Vlan510-IsTak
access-group Vlan510_access_out out interface Vlan510-IsTak
access-group Vlan600_access_in_1 in interface Vlan600-SafeQ
access-group Vlan600_access_out out interface Vlan600-SafeQ
access-group Vlan462-Suldalsposten_access_in_1 in interface Vlan462-Suldalsposten
access-group Vlan462-Suldalsposten_access_out_1 out interface Vlan462-Suldalsposten
route outside 0.0.0.0 0.0.0.0 79.x.x.225 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
username x password x encrypted privilege 15
aaa authentication ssh console LOCAL
http server enable
http 192.168.210.0 255.255.255.0 Vlan450
http 192.168.200.0 255.255.255.0 Vlan1
http 192.168.1.0 255.255.255.0 vlan400
no snmp-server location
no snmp-server contact
snmp-server community public
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map outside_map 20 match address outside_20_cryptomap_1
crypto map outside_map 20 set pfs
crypto map outside_map 20 set peer 62.92.159.137
crypto map outside_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp enable vlan400
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group 62.92.159.137 type ipsec-l2l
tunnel-group 62.92.159.137 ipsec-attributes
pre-shared-key *
telnet 192.168.200.0 255.255.255.0 Vlan1
telnet 192.168.1.0 255.255.255.0 vlan400
telnet timeout 5
ssh 171.68.225.216 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd update dns both
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan1
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface outside
dhcpd address 192.168.1.100-192.168.1.225 vlan400
dhcpd option 6 ip DomeneServer 81.167.36.11 interface vlan400
dhcpd option 3 ip 192.168.1.1 interface vlan400
dhcpd enable vlan400
dhcpd address 192.168.210.100-192.168.210.200 Vlan450
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan450
dhcpd option 3 ip 192.168.210.1 interface Vlan450
dhcpd enable Vlan450
dhcpd address 192.168.2.100-192.168.2.150 Vlan460-SuldalHotell
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan460-SuldalHotell
dhcpd option 3 ip 192.168.2.1 interface Vlan460-SuldalHotell
dhcpd enable Vlan460-SuldalHotell
dhcpd address 192.168.3.100-192.168.3.200 Vlan461-SuldalHotellGjest
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan461-SuldalHotellGjest
dhcpd option 3 ip 192.168.3.1 interface Vlan461-SuldalHotellGjest
dhcpd enable Vlan461-SuldalHotellGjest
dhcpd address 192.168.202.100-192.168.202.199 vlan470-Kyrkjekontoret
dhcpd option 3 ip 192.168.202.1 interface vlan470-Kyrkjekontoret
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan470-Kyrkjekontoret
dhcpd enable vlan470-Kyrkjekontoret
dhcpd option 3 ip 192.168.20.1 interface vlan480-Telefoni
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan480-Telefoni
dhcpd address 192.168.10.80-192.168.10.90 Vlan490-QNapBackup
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan490-QNapBackup
dhcpd option 3 ip 192.168.10.1 interface Vlan490-QNapBackup
dhcpd address 192.168.30.100-192.168.30.199 Vlan500-HellandBadlands
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan500-HellandBadlands
dhcpd option 3 ip 192.168.30.1 interface Vlan500-HellandBadlands
dhcpd enable Vlan500-HellandBadlands
dhcpd address 192.168.40.100-192.168.40.150 Vlan510-IsTak
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan510-IsTak
dhcpd option 3 ip 192.168.40.1 interface Vlan510-IsTak
dhcpd enable Vlan510-IsTak
dhcpd address 192.168.50.150-192.168.50.199 Vlan600-SafeQ
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan600-SafeQ
dhcpd enable Vlan600-SafeQ
dhcpd address 192.168.4.100-192.168.4.150 Vlan462-Suldalsposten
dhcpd option 6 ip DomeneServer 81.167.36.11 interface Vlan462-Suldalsposten
dhcpd option 3 ip 192.168.4.1 interface Vlan462-Suldalsposten
dhcpd enable Vlan462-Suldalsposten
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
prompt hostname context
Cryptochecksum:x
: end
Config site 1:
: Saved
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password x encrypted
passwd x encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.77.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group Telenor
ip address pppoe setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
switchport access vlan 15
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_access_in extended permit icmp any any echo-reply log disable
access-list outside_1_cryptomap extended permit ip 192.168.77.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.77.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.77.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 79.160.252.226
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.77.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn group Telenor request dialout pppoe
vpdn group Telenor localname x
vpdn group Telenor ppp authentication chap
vpdn username x password x store-local
dhcpd auto_config outside
dhcpd address 192.168.77.100-192.168.77.130 inside
dhcpd dns 192.168.77.1 interface inside
dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface inside
dhcpd enable inside
dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface outside
tunnel-group 79.160.252.226 type ipsec-l2l
tunnel-group 79.160.252.226 ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:x
: endHi,
The addition of a new network to the existing L2L VPN should be a pretty simple process.
Essentially you will have to add the network to the Crypto ACL present in the "crypto map" configurations. You will also have to configure the NAT0 configuration for it in the proper interfaces of the ASA. These configurations are all done on both ends of the L2L VPN connection.
Looking at your above configurations it would seem that you will need the following configurations
SITE 1
We add the new network to both the crypto ACL and the NAT0 ACL
access-list outside_1_cryptomap extended permit ip 192.168.77.0 255.255.255.0 192.168.20.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.77.0 255.255.255.0 192.168.20.0 255.255.255.0
SITE 2
We add the new network to the crypto ACL
We create a new NAT0 configuration for the Vlan480 interface as it has no previous NAT0 configuration
access-list outside_20_cryptomap_1 extended permit ip 192.168.20.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list VLAN480-NAT0 remark NAT0 for VPN
access-list VLAN480-NAT0 permit ip 192.168.20.0 255.255.255.0 192.168.77.0 255.255.255.0
nat (vlan480-Telefoni) 0 access-list VLAN480-NAT0
These configurations should pretty much do the trick.
Let me know if it worked
- Jouni -
Cisco asa 5505: No traffic lan to wan with IPv6
Hello everybody,
I have a Cisco ASA 5505, public ipv6 in outside interface, private ipv6 in LAN, from router I can ping any ipv6 in Internet and ping my LAN ipv6. Traffic doesn't go through router.
This is my configuration.
interface Vlan1
nameif inside
security-level 100
ip address PRIV-Saturn1 255.255.255.0
ipv6 address fc00::1/7
ipv6 enable
interface Vlan2
nameif outside
security-level 0
ip address PUBLIC26 255.255.255.248
ipv6 address xxxx:yyyy:67:36::2/64
ipv6 enable
ipv6 nd suppress-ra
access-list Dynamic_Filter_ACL extended permit tcp any6 any6
ipv6 route outside ::/0 xxx:yyyy:67:36::1
Am I omitting anything?
Thanks in advance for the help.
Jos PSince you're using IPv6 private addressing (fc00::) on the inside, you need a dynamic NAT entry to translate your private IPv6 addresses to a public one.
Alternatively, you could just use a subnet of your registered IPv6 block for the inside network and not worry about NAT. -
Cisco ASA 5505 Site to Site VPN tunnel up, but not passing traffic
Thanks to a previous thread, I do have a 5505 up and running, and passing data....
https://supportforums.cisco.com/message/3900751
Now I am trying to get a IPSEC VPN tunnel working.
I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
The networks concerned:
name 10.0.0.0 Eventual (HQ Site behind Firewall)
name 1.1.1.0 CFS (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)
name 2.2.2.0 T1 (Remote site - Outside interface of 5505: 2.2.2.2)
name 10.209.0.0 Local (Remote Network - internal interface of 5505: 10.209.0.3)
On a ping to the HQ network from behind the ASA, I get....
portmap translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work.
Below is the config.
Can anyone see if there is something sticking out?
: Saved
ASA Version 8.2(5)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.0 Eventual
name 10.209.0.0 Local
name 2.2.2.0 T1
name 1.1.1.0 CFS
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 10.209.0.3 255.0.0.0
interface Vlan2
nameif outside
security-level 0
ip address 2.2.2.2 255.255.255.248
time-range Indefinite
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
protocol-object udp
protocol-object tcp
object-group network DM_INLINE_NETWORK_1
network-object Eventual 255.0.0.0
network-object T1 255.255.255.248
network-object CFS 255.255.255.240
access-list outside_1_cryptomap extended permit ip Local 255.255.255.0 object-group DM_INLINE_NETWORK_1
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 67.139.113.217 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Eventual 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 1.1.1.1
crypto map outside_map 1 set transform-set ESP-3DES-MD5
crypto map outside_map 1 set phase1-mode aggressive
crypto map outside_map interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 10.209.0.201-10.209.0.232 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-policy FTMGP internal
group-policy FTMGP attributes
vpn-idle-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 general-attributes
default-group-policy FTMGP
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:701d8da28ee256692a1e49d904e9cb04
: end
asdm location Eventual 255.0.0.0 inside
asdm location Local 255.255.255.0 inside
asdm location T1 255.255.255.248 inside
asdm location CFS 255.255.255.240 inside
asdm history enable
Thank You.I'm just re-engaging on the firewall this afternoon, but right now I'm getting request timed out on the pings....
Here's the output requested:
Result of the command: "show crypto isakmp sa"
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 1.1.1.1
Type : L2L Role : initiator
Rekey : no State : AM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
Crypto map tag: outside_map, seq num: 1, local addr: 2.2.2.2
access-list outside_1_cryptomap extended permit ip 10.209.0.0 255.255.255.0 10.0.0.0 255.0.0.0
local ident (addr/mask/prot/port): (Local/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (Eventual/255.0.0.0/0/0)
current_peer: 1.1.1.1
#pkts encaps: 84, #pkts encrypt: 84, #pkts digest: 84
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 84, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 2.2.2.2, remote crypto endpt.: 1.1.1.1
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 8FC06BD1
current inbound spi : 42EC16F4
inbound esp sas:
spi: 0x42EC16F4 (1122768628)
transform: esp-3des esp-md5-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 4096, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (62207/28464)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
outbound esp sas:
spi: 0x8FC06BD1 (2411752401)
transform: esp-3des esp-md5-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 4096, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (62201/28464)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Here's the current config:
: Saved
ASA Version 8.2(5)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.0 Eventual
name 10.209.0.0 Local
name 67.139.113.216 T1
name 1.1.1.0 IntegraCFS
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 10.209.0.3 255.0.0.0
interface Vlan2
nameif outside
security-level 0
ip address 2.2.2.2 255.255.255.248
time-range Indefinite
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
protocol-object udp
protocol-object tcp
object-group network DM_INLINE_NETWORK_1
network-object Eventual 255.0.0.0
network-object T1 255.255.255.248
network-object IntegraCFS 255.255.255.240
access-list outside_1_cryptomap extended permit ip Local 255.255.255.0 object-group DM_INLINE_NETWORK_1
access-list No_NAT extended permit ip Local 255.255.255.0 Eventual 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list No_NAT
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 2.2.2.0 1
route outside Eventual 255.255.255.0 1.1.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Eventual 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 1.1.1.1
crypto map outside_map 1 set transform-set ESP-3DES-MD5
crypto map outside_map 1 set security-association lifetime kilobytes 65535
crypto map outside_map 1 set phase1-mode aggressive
crypto map outside_map interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 10.209.0.201-10.209.0.232 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-policy FTMGP internal
group-policy FTMGP attributes
vpn-idle-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 general-attributes
default-group-policy FTMGP
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:301e573544ce0f89b3c597bdfe2c414a
: end
asdm location Eventual 255.0.0.0 inside
asdm location Local 255.255.255.0 inside
asdm location T1 255.255.255.248 inside
asdm location IntegraCFS 255.255.255.240 inside
asdm history enable -
Cisco ASA 5505 Remote Access IP/Sec VPN Connectivity Issues
We have a Cisco ASA that we use just for Remote Access VPN. It uses UDP and was working fine for about 2 months. Recently clients have had intermittent issues when connecting from home. The following message is display by the Cisco VPN Client :
"Secure VPN connection terminated locally by the Client. Reason 412: The remote peer is no longer responding"
Upon looking at a client side packet capture, I notice that no response is being given back to the client for the udp packets sent to the ASA on udp 500. If I login to the ASA from the LAN and send a single ping FROM the ASA, then the client can connect without issue. I don't understand the significance of the needed outbound ping since ping is not used by the client to test if the ASA is alive.
Once again this is a remote access udp ip/sec VPN. I set most of it up with the VPN wizard and then backed up the config. The issue started happening at least a month after setup (maybe two) and I restored to the saved config just in-case, but the issue remains.
Any insight would be greatly appreciated.
I'm using IOS 831 and have tried 821 and 823 as one thread that I found recommended downgraded to 821.
Thanks much,
JustinJavier,
I logged into the ASA last time the VPN went down. I issued the following commands:
debug crypto isakmp 190
debug crypto ipsec 190
capture outside-cap interface outside match udp any any
I then used a remote access tool to access the client and tried to connect. I got absolutely nothing from debugging. So I issued the following command:
show capture outside | include 500
and also got nothing. So I issued the following command:
ping 4.2.2.2
Upon which my normal deug messaged began to showup, so I issued the show capture outside command again and recieved the expected output below:
1: 15:44:18.570160 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 868
2: 15:44:18.579269 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 444
3: 15:44:18.703866 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 172
4: 15:44:18.706567 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 76
5: 15:44:18.831499 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 92
6: 15:44:19.024061 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 76
7: 15:44:19.111963 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 60
8: 15:44:19.517185 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 204
9: 15:44:19.521350 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 92
10: 15:44:19.522723 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 252
11: 15:44:42.121957 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 868
12: 15:44:42.130822 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 444
13: 15:44:42.228397 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 172
14: 15:44:42.231036 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 76
15: 15:44:42.329557 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 92
16: 15:44:42.521091 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 76
17: 15:44:42.610167 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 60
18: 15:44:42.649258 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 204
19: 15:44:42.653790 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 252
20: 15:44:42.789342 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 1036
21: 15:44:42.792119 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 92
22: 15:44:42.800846 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 188
23: 15:44:42.892120 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 60
34: 15:44:54.446220 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 92
35: 15:44:54.447913 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 92
70: 15:45:01.825000 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000: udp 100
174: 15:45:03.417764 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000: udp 500
377: 15:45:07.881500 802.1Q vlan#2 P0 REMOTE_IP.10000 > OFFICE_IP.10000: udp 100 1: 15:44:18.570160 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 868
2: 15:44:18.579269 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 444
3: 15:44:18.703866 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 172
4: 15:44:18.706567 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 76
5: 15:44:18.831499 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 92
6: 15:44:19.024061 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 76
7: 15:44:19.111963 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 60
8: 15:44:19.517185 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 204
9: 15:44:19.521350 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 92
10: 15:44:19.522723 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 252
11: 15:44:42.121957 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 868
12: 15:44:42.130822 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 444
13: 15:44:42.228397 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 172
14: 15:44:42.231036 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 76
15: 15:44:42.329557 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 92
16: 15:44:42.521091 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 76
17: 15:44:42.610167 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 60
18: 15:44:42.649258 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 204
19: 15:44:42.653790 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 252
20: 15:44:42.789342 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 1036
21: 15:44:42.792119 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 92
22: 15:44:42.800846 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 188
23: 15:44:42.892120 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 60
34: 15:44:54.446220 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 92
35: 15:44:54.447913 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 92
70: 15:45:01.825000 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000: udp 100
174: 15:45:03.417764 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000: udp 500
377: 15:45:07.881500 802.1Q vlan#2 P0 REMOTE_IP.10000 > OFFICE_IP.10000: udp 100
It would seem as if no traffic reached the ASA until some outbound traffic to an arbitrary public IP. In this case I sent an echo request to a public DNS server. It seems almost like a state-table issue although I don't know how ICMP ties in.
Once again, any insight would be greatly appreciated.
Thanks,
Justin -
Hello, I am having some issues configuring two ASA's for Site to Site and am seeking some help. I greatly appreciate your times and efforts. When I do a
L2Lsite2# show crypto isakmp sa
There are no isakmp sas
L2Lsite2# show crypto ipsec sa
There are no ipsec sas
If I am on side L2Lsite1 I cannot ping 192.168.3.1
Will repost configs later.
Thanks again in advance for your help in this important issue.Hello,
I am in need of more help. Now that I have moved the installation I cannot get it to work properly. The issue is the two asa's can ping eachothers inside interfaces just fine(see below) but they cannot ping any other devices on the network(see below). This issue relates to both sides. Thanks in advance.
L2Lsite2# ping inside 10.0.0.5 (site1's internal IP)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.5, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 30/36/40 ms
L2Lsite2# ping inside 10.0.0.1(device on site1's network)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
Success rate is 0 percent (0/5)
The help is greatly appreciated.
Side 1:
L2LSite1# sh run
: Saved
ASA Version 7.2(3)
hostname L2LSite1
enable password 0M8kPLt5hmzMzfqa encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.5 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list crypto_acl extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0
access-list do_not_nat extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0
pager lines 24
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-523.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list do_not_nat
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
aaa authentication ssh console LOCAL
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set encryption_type_set esp-3des esp-sha-hmac
crypto map outside_map 20 match address crypto_acl
crypto map outside_map 20 set pfs
crypto map outside_map 20 set peer x.x.x.x
crypto map outside_map 20 set transform-set encryption_type_set
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 5
console timeout 5
management-access inside
class-map inspection_default
match default-inspection-traffic
class-map class
match default-inspection-traffic
policy-map type inspect dns dns_inspection
parameters
message-length maximum 512
policy-map policy
class class
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect snmp
inspect http
inspect dns dns_inspection
service-policy policy global
username aplus password m6zItLhnhjBU/z6I encrypted
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group x.x.x.x ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:ef9e72ae4d06957f050dbc1fd16a842c
: end
L2LSite1# sh ipsec sa
interface: outside
Crypto map tag: outside_map, seq num: 20, local addr: x.x.x.x
access-list crypto_acl permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0
local ident (addr/mask/prot/port): (10.0.0.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (10.0.1.0/255.255.255.0/0/0)
current_peer: x.x.x.x
#pkts encaps: 17, #pkts encrypt: 17, #pkts digest: 17
#pkts decaps: 7, #pkts decrypt: 7, #pkts verify: 7
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 17, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.x, remote crypto endpt.: x.x.x.x
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 14952F72
inbound esp sas:
spi: 0x009CB49C (10269852)
transform: esp-3des esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 7, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (3824999/28369)
IV size: 8 bytes
replay detection support: Y
outbound esp sas:
spi: 0x14952F72 (345321330)
transform: esp-3des esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 7, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (3824998/28369)
IV size: 8 bytes
replay detection support: Y
L2LSite1# packet-tracer input inside icmp 10.0.0.5 8 8 10.0.1.6
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 outside
Phase: 3
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
Site 2:
L2Lsite2# sh run
: Saved
ASA Version 7.2(4)
hostname L2Lsite2
enable password 0M8kPLt5hmzMzfqa encrypted
passwd 0M8kPLt5hmzMzfqa encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 10.0.1.49 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 8.8.8.8
access-list crypto_acl extended permit ip 10.0.1.0 255.255.255.0 10.0.0.0 255.255.255.0
access-list do_not_nat extended permit ip 10.0.1.0 255.255.255.0 10.0.0.0 255.255.255.0
pager lines 24
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin\
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list do_not_nat
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa authentication ssh console LOCAL
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set encryption_type_set esp-3des esp-sha-hmac
crypto map outside_map 20 match address crypto_acl
crypto map outside_map 20 set pfs
crypto map outside_map 20 set peer x.x.x.x
crypto map outside_map 20 set transform-set encryption_type_set
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 5
console timeout 5
management-access inside
username aplus password m6zItLhnhjBU/z6I encrypted
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group x.x.x.x ipsec-attributes
pre-shared-key *
class-map class
match default-inspection-traffic
policy-map type inspect dns dns_inspection
parameters
message-length maximum 512
policy-map policy
class class
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect snmp
inspect http
inspect dns dns_inspection
service-policy policy global
prompt hostname context
Cryptochecksum:4d1dc33d95e4d294a1c96473ef81a393
: end
L2Lsite2# sh ipsec sa
interface: outside
Crypto map tag: outside_map, seq num: 20, local addr: x.x.x.x
access-list crypto_acl permit ip 10.0.1.0 255.255.255.0 10.0.0.0 255.255.255.0
local ident (addr/mask/prot/port): (10.0.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (10.0.0.0/255.255.255.0/0/0)
current_peer: x.x.x.x
#pkts encaps: 9, #pkts encrypt: 9, #pkts digest: 9
#pkts decaps: 19, #pkts decrypt: 19, #pkts verify: 19
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 9, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.x , remote crypto endpt.: x.x.x.x
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 009CB49C
inbound esp sas:
spi: 0x14952F72 (345321330)
transform: esp-3des esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 7, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4274998/28008)
IV size: 8 bytes
replay detection support: Y
outbound esp sas:
spi: 0x009CB49C (10269852)
transform: esp-3des esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 7, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4274999/28008)
IV size: 8 bytes
replay detection support: Y
L2Lsite2# packet-tracer input inside icmp 10.0.1.49 8 8 10.0.0.1
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 outside
Phase: 3
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
Thanks again! -
Setting up site to site IPSec VPN with RV 120W
Hi All,
I am looking to set up a site to site VPN between a local and remote office, with a RV 120w as the gateway at either side. Aside from changing the remote site's IP and Subnet, what do I need to do to get this functional? to call myself a well tooled novice would be appropriate. Any help is appreciated.
Thanks,
ScottYou will most likely need to call the Cisco Small Business Support Center at 1-866-606-1866 so that
we can assist you in setting up the Gateway to Gateway VPN Tunnel.
THANKS
Rick Roe
Cisco Small Business Support Center -
Cisco ASA Site to Site IPSEC VPN and NAT question
Hi Folks,
I have a question regarding both Site to Site IPSEC VPN and NAT. Basically what I want to achieve is to do the following:
ASA2 is at HQ and ASA1 is a remote site. I have no problem setting up a static static Site to Site IPSEC VPN between sites. Hosts residing at 10.1.0.0/16 are able to communicate with hosts at 192.168.1.0/24, but what i want is to setup NAT with IPSEC VPN so that host at 10.1.0.0/16 will communicate with hosts at 192.168.1.0/24 with translated addresses
Just an example:
Host N2 (10.1.0.1/16) will communicate with host N1 192.168.1.5 with destination lets say 10.23.1.5 not 192.168.1.5 (Notice the last octet should be the same in this case .5)
The same translation for the rest of the communication (Host N2 pings host N3 destination ip 10.23.1.6 not 192.168.1.6. again last octet is the same)
It sounds a bit confusing for me but i have seen this type of setup before when I worked for managed service provider where we had connection to our clients (Site to Site Ipsec VPN with NAT, not sure how it was setup)
Basically we were communicating with client hosts over site to site VPN but their real addresses were hidden and we were using translated address as mentioned above 10.23.1.0/24 instead of (real) 192.168.1.0/24, last octet should be the same.
Appreciate if someone can shed some light on it.Hi,
Ok so were going with the older NAT configuration format
To me it seems you could do the following:
Configure the ASA1 with Static Policy NAT
access-list L2LVPN-POLICYNAT permit ip 192.168.1.0 255.255.255.0 10.1.0.0 255.255.0.0
static (inside,outside) 10.23.1.0 access-list L2LVPN-POLICYNAT
Because the above is a Static Policy NAT it means that the translation will only be done when the destination network is 10.1.0.0/16
If you for example have a basic PAT configuration for inside -> outside traffic, the above NAT configuration and the actual PAT configuration wont interfere with eachother
On ASA2 side you can normally configure NAT0 / NAT Exemption for the 10.1.0.0/16 network
access-list INSIDE-NONAT remark L2LVPN NONAT
access-list INSIDE-NONAT permit ip 10.1.0.0 255.255.0.0 10.23.1.0 255.255.255.0
nat (inside) 0 access-list INSIDE-NONAT
You will have to take into consideration that your access-list defining the L2L-VPN encrypted traffic must reflect the new NAT network
ASA1: access-list L2LVPN-ENCRYPTIONDOMAIN permit ip 10.23.1.0 255.255.255.0 10.1.0.0 255.255.0.0
ASA2: access-list L2LVPN-ENCRYPTIONDOMAIN permit ip 10.1.0.0 255.255.0.0 10.23.1.0 255.255.255.0
I could test this setup tomorrow at work but let me know if it works out.
Please rate if it was helpful
- Jouni -
Setting up site to site vpn with cisco asa 5505
I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
IP of remote office router is 71.37.178.142
IP of the main office firewall is 209.117.141.82
Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
ciscoasa# show run
: Saved
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password TMACBloMlcBsq1kp encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group5
crypto map outside_map 1 set peer 209.117.141.82
crypto map outside_map 1 set transform-set ESP-AES-256-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn username [email protected] password ********* store-local
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.129 inside
dhcpd enable inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
: end
ciscoasa#
Thanks!Hi Mandy,
By using following access list define Peer IP as source and destination
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
you are not defining the interesting traffic / subnets from both ends.
Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
!.1..source subnet(called local encryption domain) at your end 192.168.200.0
!..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
!..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
!...at your end 192.168.200.0
!..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
!...at other end 192.168.100.0
Please use Baisc Steps as follows:
A. Configuration in your MAIN office having IP = 209.117.141.82 (follow step 1 to 6)
Step 1.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
Step 2.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256 --->2nd parameter of ISAKMP Policy is OK
hash sha ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 3.
Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 71.37.178.142
or , but not both
crypto isakmp key 6 CISCO123 address71.37.178.142
step 4.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 5.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 6.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Configure the same but just change ACL on other end in step one by reversing source and destination
and also set the peer IP of this router in other end.
So other side config should look as follows:
B. Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
Step 7.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
Step 8.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256 --->2nd parameter of ISAKMP Policy is OK
hash sha ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 9.
Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 209.117.141.82
or , but not both
crypto isakmp key 6 CISCO123 address 209.117.141.82
step 10.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 11.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set, only one is permissible
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 12.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Now initite a ping
Here is for your summary:
IPSec: Site to Site - Routers
Configuration Steps
Phase 1
Step 1: Configure Mirrored ACL/Crypto ACL for Interesting Traffic
Step 2: Configure ISAKMP Policy
Step 3: Configure ISAKMP Key
Phase 2
Step 4: Configure Transform Set
Step 5: Configure Crypto Map
Step 6: Apply Crypto Map to an Interface
To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
Router#debug crpyto isakmp
Router#debug crpyto ipsec
Router(config)# logging buffer 7
Router(config)# logging buffer 99999
Router(config)# logging console 6
Router# clear logging
Configuration
In R1:
(config)# access-list 101 permit ipo host 10.1.1.1 host 10.1.2.1
(config)# crypto isakmp policy 10
(config-policy)# encryption 3des
(config-policy)# authentication pre-share
(config-policy)# group 2
(config-policy)# hash sha1
(config)# crypto isakmp key 0 cisco address 2.2.2.1
(config)# crypto ipsec transform-set TSET esp-3des sha-aes-hmac
(config)# crypto map CMAP 10 ipsec-isakmp
(config-crypto-map)# set peer 2.2.2.1
(config-crypto-map)# match address 101
(config-crypto-map)# set transform-set TSET
(config)# int f0/0
(config-if)# crypto map CMAP
Similarly in R2
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Change to Transport Mode, add the following command in Step 4:
(config-tranform-set)# mode transport
Even after doing this change, the ipsec negotiation will still be done through tunnel mode if pinged from Loopback to Loopback. To overcome this we make changes to ACL.
Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
(config)# crypto isakmp peer address 2.2.2.1
(config-peer)# set aggressive-mode password cisco
(config-peer)# set aggressive-mode clien-endpoint ipv4-address 2.2.2.1
Similarly on R2.
The below process is for the negotiation using RSA-SIG (PKI) as authentication type
Debug Process:
After we debug, we can see the negotiation between the two peers. The first packet of the interesting traffic triggers the ISAKMP (Phase1) negotiation. Important messages are marked in BOLD and explanation in RED
R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 2.2.2.2
Mar 2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) // Router tried to find any IPSec SA matching the outgoing connection but no valid SA has been found in Security Association Database (SADB)
Mar 2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
Mar 2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
Mar 2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
Mar 2 16:18:42.939: ISAKMP: local port 500, remote port 500
Mar 2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE
Mar 2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
Mar 2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
Mar 2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
Mar 2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Mar 2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY New State = IKE_I_MM1
Mar 2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
Mar 2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1 New State = IKE_I_MM2
Mar 2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947:.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
R2(config)# ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
Mar 2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
Mar 2 16:18:42.947: ISAKMP: encryption 3DES-CBC
Mar 2 16:18:42.947: ISAKMP: hash SHA
Mar 2 16:18:42.947: ISAKMP: default group 2
Mar 2 16:18:42.947: ISAKMP: auth RSA sig
Mar 2 16:18:42.947: ISAKMP: life type in seconds
Mar 2 16:18:42.947: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
Mar 2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
Mar 2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
Mar 2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM2
Mar 2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
Mar 2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM3
Mar 2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
Mar 2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3 New State = IKE_I_MM4
Mar 2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
Mar 2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:43.007: Choosing trustpoint CA_Server as issuer
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
Mar 2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM4
Mar 2 16:18:43.011: ISAKMP:(1008):Send initial contact
Mar 2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
Mar 2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
Mar 2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
Mar 2 16:18:43.011: ISAKMP (1008): ID payload
next-payload : 6
type : 2
FQDN name : R2
protocol : 17
port : 500
length : 10
Mar 2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
Mar 2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
Mar 2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
Mar 2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Mar 2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM5
Mar 2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
// "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
Mar 2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP (1008): ID payload
next-payload : 6
type : 2
FQDN name : ASA1
protocol : 0
port : 0
length : 12
Mar 2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
Mar 2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
Mar 2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
Mar 2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
Mar 2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
Mar 2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
Mar 2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
Mar 2 16:18:43.067: ISAKMP:received payload type 17
Mar 2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
Mar 2 16:18:43.067: ISAKMP:(1008):SA authentication status:
authenticated
Mar 2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
Mar 2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/, and inserted successfully 46519678. // SA inserted into SADB
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5 New State = IKE_I_MM6
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_I_MM6
Mar 2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_P1_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
Mar 2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
Mar 2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY New State = IKE_QM_I_QM1
Mar 2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
Mar 2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
Mar 2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
Mar 2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
Mar 2 16:18:43.079: ISAKMP: attributes in transform:
Mar 2 16:18:43.079: ISAKMP: SA life type in seconds
Mar 2 16:18:43.079: ISAKMP: SA life duration (basic) of 3600
Mar 2 16:18:43.079: ISAKMP: SA life type in kilobytes
Mar 2 16:18:43.079: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
Mar 2 16:18:43.079: ISAKMP: encaps is 1 (Tunnel)
Mar 2 16:18:43.079: ISAKMP: authenticator is HMAC-SHA
Mar 2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
Mar 2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
Mar 2 16:18:43.083: inbound SA from 20.1.1.10 to 40.1.1.1 (f/i) 0/ 0
(proxy 1.1.1.1 to 2.2.2.2)
Mar 2 16:18:43.083: has spi 0xA9A66D46 and conn_id 0
Mar 2 16:18:43.083: lifetime of 3600 seconds
Mar 2 16:18:43.083: lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
(proxy 2.2.2.2 to 1.1.1.1)
Mar 2 16:18:43.083: has spi 0x2B367FB4 and conn_id 0
Mar 2 16:18:43.083: lifetime of 3600 seconds
Mar 2 16:18:43.083: lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
Mar 2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
Mar 2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1 New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Kindly rate if you find the explanation useful !!
Best Regards
Sachin Garg -
Azure Site to Site VPN with Cisco ASA 5505
I have got Cisco ASA 5505 device (version 9.0(2)). And i cannot connect S2S with azure (azure network alway in "connecting" state). In my cisco log:
IP = 104.40.182.93, Keep-alives configured on but peer does not support keep-alives (type = None)
Group = 104.40.182.93, IP = 104.40.182.93, QM FSM error (P2 struct &0xcaaa2a38, mess id 0x1)!
Group = 104.40.182.93, IP = 104.40.182.93, Removing peer from correlator table failed, no match!
Group = 104.40.182.93, IP = 104.40.182.93,Overriding Initiator's IPSec rekeying duration from 102400000 to 4608000 Kbs
Group = 104.40.182.93, IP = 104.40.182.93, PHASE 1 COMPLETED
I have done all cisco s2s congiguration over standard wizard cos seems your script for 8.x version of asa only?
(Does azure support 9.x version of asa?)
How can i fix it?Hi,
As of now, we do not have any scripts for Cisco ASA 9x series.
Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as
demonstrated in this blog:
Step-By-Step: Create a Site-to-Site VPN between your network and Azure
http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
You can refer to this article for Cisco ASA templates for Static routing:
http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
Did you download the VPN configuration file from the dashboard and copy the content of the configuration
file to the Command Line Interface of the Cisco ASDM application? It seems that there is no specified IP address in the access list part and maybe that is why the states message appeared.
According to the
Cisco ASA template, it should be similar to this:
access-list <RP_AccessList>
extended permit ip object-group
<RP_OnPremiseNetwork> object-group <RP_AzureNetwork>
nat (inside,outside) source static <RP_OnPremiseNetwork>
<RP_OnPremiseNetwork> destination static <RP_AzureNetwork>
<RP_AzureNetwork>
Based on my experience, to establish
IPSEC tunnel, you need to allow the ESP protocol and UDP Port 500. Please make sure that the
VPN device cannot be located behind a NAT. Besides, since Cisco ASA templates are not
compatible for dynamic routing, please make sure that you chose the static routing.
Since you configure the VPN device yourself, it's important that you would be familiar with the device and its configuration settings.
Hope this helps you.
Girish Prajwal -
Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: endThanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
Desc: (none)
Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
Active SAs: 0, origin: crypto map
Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help.
Maybe you are looking for
-
HT4623 WHY IS MY IPAD HAVE A PASSCODE AFTER I UPDATED THE NEW VERSION?
why is my ipad have a passcode after updating new version?
-
Hi How to post a direct entry in reconciliation a/c.I was passing a jv in TC-FB01 to a recon a/c. it is not allowed me to post.please explain how to post. thanks shivaji
-
Single Tabular structure of boxes for more than one form?
Hey everone ! Can i use a Single Tabular structure for more than one form ? Coz i need the same structure for all my forms and its getting really tough to create it for each and every form ?
-
Why does my I phone 3 keep searching for signal
Why does my I phone3 keep searching for a signal
-
Since downloading osx v10.7lion every time i try to connect to the internet using BT Broadband i keep getting a message saying " you cant openthe application ) because Power PC applications are no longer supported." this is very annoying as i likeBT