Cisco ASA 5520 traffic between interfaces
Hello,
I am new in the Cisco world , learning how everything goes. I have a Cisco ASA 5520 firewall that i am trying to configure, but i am stumped. Traffic does not pass trough interfaces ( i tried ping ) , although packet tracer shows everything as ok. I have attached the running config and the packet tracer. The ip's i am using in the tracer are actual hosts.
ciscoasa# ping esx_management 192.168.10.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.100, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
ciscoasa# ping home_network 192.168.10.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.100, timeout is 2 seconds:
Success rate is 0 percent (0/5)
Thank you in advance.
Hi,
Is this just a testing setup? I would suggest changing "internet" interface to "security-level 0" (just for the sake of identifying its an external interface) and not allowing all traffic from there.
I am not sure what your "packet-tracer" is testing. If you wanted to test ICMP Echo it would be
packet-tracer input home_network icmp 10.192.5.5 8 0 255 192.168.10.100
I see that you have not configured any NAT on the ASA unit. In the newer ASA software that would atleast allow communication between all interface with their real IP addresses.
I am not so sure about the older ASA versions anymore. To my understanding the "no nat-control" is default setting in your model which basically states that there is no need for NAT configurations between the interfaces the packet is going through.
Have you confirmed that all the hosts/servers have the correct default gateway/network mask configurations so that traffic will flow correctly outside their own network?
Have you confirmed that there are no firewall software on the actual server/host that might be blocking this ICMP traffic from other networks?
Naturally if wanted to try some NAT configurations you could try either of these for example just for the sake of testing
Static Identity NAT
static (home_network,esx_management) 192.168.5.0 192.168.5.0 mask 255.255.255.0
static (home_network,DMZ) 192.168.5.0 192.168.5.0 mask 255.255.255.0
static (home_network,management) 192.168.5.0 192.168.5.0 mask 255.255.255.0
OR
NAT0
access-list HOMENETWORK-NAT0 remark NAT0 to all local networks
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.10.0 255.255.255.0
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.20.0 255.255.255.0
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.1.0 255.255.255.0
nat (home_network) 0 access-list HOMENETWORK-NAT0
Hope this helps
- Jouni
Similar Messages
-
Cisco ASA 5520 Traffic monitoring
Hello ,
We have a Cisco ASA 5520 and im looking for a way to monitor largest outgoing and incoming traffic per ip in real time so to know which of my internal computers are using the most of our Internet Line. Is there a way to this through ADSM ? We use version 6.3.
Thanks a lotHi,
I dont think the ASA alone can give you a really clear picture of the real time situation.
It however should be able to give you some clue and simple statistics on the ASDM Firewall Dashboard
My ASDM version is 7.1 but it should be there in your version also. -
HA between a Cisco ASA 5520 and a Cisco ASA 5525-X
Hi all!
we have a couple of Cisco ASA 5520 running 8.4(3) software, and we want to improve throughput changing them with a couple of Cisco ASA 5525-X. Since software is theorically compatible, we are not going to upgrade it right now.
We don't want to stop service, so we are thinking about switching off backup 5520 firewall, change it with a 5525-X and balance service to that one while we change the other 5520 fw. So the question is, has someone tried to make an active-pasive cluster with both technologies, Cisco ASA an Cisco ASA-X firewalls? We were said that it should be theorically compatible, but we'd like to know if someone tried before.
Best regards for all,You cannot make a 5520 establish failover with the mate being a 5525-X.
1. The configuration guide (here) states:
The two units in a failover configuration must be the same model, have the same number and types of interfaces, the same SSMs installed (if any), and the same RAM installed.
2. A 5525-X requires 8.6 software. 8.6 does not support non-X series ASAs. (Reference) Even if you wait until 9.0 is available (next month) for both you still fail on the model and RAM (X series has much more than the 5520) checks noted above. -
Site to Site VPN between Cisco ASA 5520 and Avaya VPN Phone
Hi,
I am wondering if anyone can assist me on configuring Cisco ASA 5520 site to site vpn with Avaya VPN Phone? According to Avaya, the Avaya 9630 phone acts as a VPN client so a VPN router or firewall is not needed.
The scanario:
Avaya System ------ ASA 5520 ------ INTERNET ----- Avaya 9630 VPN Phone
Any help or advice is much appreciated.
Thanks.Hello Bernard,
What you are looking for is a Remote Ipsec VPN mode not a L2L.
Here is the link you should use to make this happen:)
https://devconnect.avaya.com/public/download/interop/vpnphon_asa.pdf
Regards,
Julio -
Cisco ASA 5520 Site-to-site VPN TUNNELS disconnection problem
Hi,
i recently purchased a Cisco ASA 5520 and running firmware v. 8.4(2) and ASDM v. 6.4(5)106.
I have installed 50 Site-to-Site VPN tunnels, and they work fine.
but randomly the VPN Tunnels keep disconnecting and few seconds after it connects it self automaticly....
it happens when there is no TRAFIC on, i suspect.
in ASDM in Group Policies under DfltGrpPolicy (system default) i have "idle timeout" to "UNLMITED" but still they keep disconnecting and connecting again... i have also verified that all VPN TUNNELS are using this Group Policie. and all VPN tunnels have "Idle Timeout: 0"
this is very annoying as in my case i have customers having a RDP (remote dekstop client) open 24/7 and suddenly it gets disconnected due to no traffic ?
in ASDM under Monitoring -> VPN .. i can see all VPN tunnels recently disconnected in "Login Time Duration"... some 30minutes, 52minutes, 40minutes and some 12 minutes ago.. and so on... they dont DISCONNECT at SAME time.. all randomly..
i dont WANT the VPN TUNNELS to disconnect, i want them to RUN until we manually disconnect them.
Any idea?
Thanks,
DanielWhat is the lifetime value configured for in your crypto policies?
For example:
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400 -
Cisco ASA 5520 Failover with DMZ
I have a pair of Cisco ASA 5520s running as a primary/standby. Everything is working properly with the primary ASA, however when I trigger a failover, everything works except for the DMZ interface on the standby ASA. I've poured over the configs, but perhaps I have been staring at them too long because I am just not seeing anything.
Below is the output of the sh run failover, sh failover, and sh run interface commands for each unit...
PRIMARY ASA
Primary-ASA# sh run failover
failover
failover lan unit primary
failover lan interface stateful1 GigabitEthernet0/3
failover key *****
failover link stateful1 GigabitEthernet0/3
failover interface ip stateful1 192.168.216.1 255.255.255.0 standby 192.168.216.2
Primary-ASA# sh failover
Failover On
Failover unit Primary
Failover LAN Interface: stateful1 GigabitEthernet0/3 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 3 of 160 maximum
Version: Ours 8.2(5), Mate 8.2(5)
Last Failover at: 20:39:23 CDT Sep 3 2013
This host: Primary - Active
Active time: 69648 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(5)) status (Up Sys)
Interface outside (184.61.38.254): Normal
Interface inside (192.168.218.252): Normal
Interface dmz (192.168.215.254): Normal (Waiting)
Interface management (192.168.1.1): Normal (Not-Monitored)
slot 1: ASA-SSM-10 hw/sw rev (1.0/6.0(3)E1) status (Up/Up)
IPS, 6.0(3)E1, Up
Other host: Secondary - Standby Ready
Active time: 2119 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(5)) status (Up Sys)
Interface outside (184.61.38.253): Normal
Interface inside (192.168.218.253): Normal
Interface dmz (192.168.215.252): Normal (Waiting)
Interface management (192.168.1.2): Normal (Not-Monitored)
slot 1: ASA-SSM-10 hw/sw rev (1.0/6.0(3)E1) status (Up/Up)
IPS, 6.0(3)E1, Up
Primary-ASA# sh run interface
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 184.61.38.254 255.255.255.128 standby 184.61.38.253
ospf cost 10
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 192.168.218.252 255.255.255.0 standby 192.168.218.253
ospf cost 10
interface GigabitEthernet0/2
nameif dmz
security-level 50
ip address 192.168.215.254 255.255.255.0 standby 192.168.215.252
ospf cost 10
interface GigabitEthernet0/3
description LAN/STATE Failover Interface
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0 standby 192.168.1.2
ospf cost 10
management-only
STANDBY ASA
Standby-ASA# sh run failover
failover
failover lan unit secondary
failover lan interface stateful1 GigabitEthernet0/3
failover key *****
failover link stateful1 GigabitEthernet0/3
failover interface ip stateful1 192.168.216.1 255.255.255.0 standby 192.168.216.2
Standby-ASA# sh failover
Failover On
Failover unit Secondary
Failover LAN Interface: stateful1 GigabitEthernet0/3 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 3 of 160 maximum
Version: Ours 8.2(5), Mate 8.2(5)
Last Failover at: 20:39:23 CDT Sep 3 2013
This host: Secondary - Standby Ready
Active time: 2119 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(5)) status (Up Sys)
Interface outside (184.61.38.253): Normal
Interface inside (192.168.218.253): Normal
Interface dmz (192.168.215.252): Normal (Waiting)
Interface management (192.168.1.2): Normal (Not-Monitored)
slot 1: ASA-SSM-10 hw/sw rev (1.0/6.0(3)E1) status (Up/Up)
IPS, 6.0(3)E1, Up
Other host: Primary - Active
Active time: 70110 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(5)) status (Up Sys)
Interface outside (184.61.38.254): Normal
Interface inside (192.168.218.252): Normal
Interface dmz (192.168.215.254): Normal (Waiting)
Interface management (192.168.1.1): Normal (Not-Monitored)
slot 1: ASA-SSM-10 hw/sw rev (1.0/6.0(3)E1) status (Up/Up)
IPS, 6.0(3)E1, Up
Standby-ASA# sh run interface
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 184.61.38.254 255.255.255.128 standby 184.61.38.253
ospf cost 10
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 192.168.218.252 255.255.255.0 standby 192.168.218.253
ospf cost 10
interface GigabitEthernet0/2
nameif dmz
security-level 50
ip address 192.168.215.254 255.255.255.0 standby 192.168.215.252
ospf cost 10
interface GigabitEthernet0/3
description LAN/STATE Failover Interface
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0 standby 192.168.1.2
ospf cost 10
management-only
Does anyone see something I might be missing? I am at a loss...I'll just answer my own question...the configs are correct, but it the interface on the standby ASA was plugged into an improperly configured switchport. That'll do it everytime.
-
I have cisco asa 5520 firewall in production sudenly yetserday firewall was reboted and crashinfo file was genetrated(check with command show crashinfo)
But unable to undersatand the terms
I want to know below thing regarding crashinfo
1) In asa where crashinfo file stores and file name(please share commnad for checking)
2) How to copy file from device to machine
3) How to read that file(any tool any software)The crashinfo file ("show crashinfo") is plain text and along with the memory register contents there is a whole long list of other information - running-configuration, interface status and counters, etc. So you can look at it in any text editor or even on the ASA console itself.
As far as learning from it directly, there is plenty to learn and use without knowing the most detailed possible level of debug information.
If you want to see some of the tools that are available (and may include some of the crashinfo data), I'd recommend to you a Cisco Live presentation like BRKSEC-3020. You can download that and any other Cisco Live presentations here with a free registration. -
Command to View LDAP Password on Cisco ASA 5520
Hello
I am migrating from a Cisco ASA 5520 (ASA version 8.4(6)5 to a Cisco ASA 5585. We have LDAP issues logging into to our vpn client software. I assume the LDAP password may be incorrectly entered on the new 5585. No service password- encryption or more running:config won't show the encrypted LDAP password. What is the command to view that?
Thanks!
MattThankyou Jennifer for the responds.
Could you please help me on how to enable "memberOf" attribute on AD to be pushed to ASA for the OU matching.
i have already set the "Remote Dialin" property of user account name "testvendor" in AD as "Allow Access" .It can be shown in the debug output as below.
[454095] sAMAccountName: value = testvendor
[454095] sAMAccountType: value = 805306368
[454095] userPrincipalName: value = [email protected]
[454095] objectCategory: value = CN=Person,CN=Schema,CN=Configuration,DC=abc,DC=local
[454095] msNPAllowDialin: value = TRUE
[454095] dSCorePropagationData: value = 20111026081253.0Z
[454095] dSCorePropagationData: value = 20111026080938.0Z
[454095] dSCorePropagationData: value = 16010101000417.0Z
Is their any other settings that i need to do it on AD ?
Kindly advice
Regards
Shiji -
Older version of openssl in cisco asa 5520
Hi,
Recently my security has scanned all the network devices for vulnerabilities and found that cisco asa 5520 , which we use for RAS VPN has older version of openssl. Have to check that and fix this problem? FYI, recently we have installed a SSL cert for webmail users.
Thanks,
SridharSridhar,
W update OpenSSL libraries on our side quite often, especially if new vulnarabilities are found.
You can check recently published vulnarabilities in www.cisco.com/go/psirt (not only specific to ASA)
In general ASA 8.4 is what you should go for to have "latest and greatest" revisions of openssl and ASA code itself.
Marcin -
Configuring Cisco ASA 5520 for Outlook Anywhere - Exchange 2007
I have enable and configured our Exchange 2007 for Outlook Anywhere. When I try to get Outlook from home to connect it fails. We have an Cisco ASA 5520 firewall at work, is there something I need to setup on the device? We want to allow users from
home to connect via their Outlook clients from home. OWA is working from the outside... Help please...Hi,
Make sure that the required ports are allowed over he device. The users can access through port 25/443 etc. and should be opened. Better, to go for a test at www.testconnectivity.microsoft.com
Regards from ExchangeOnline.in|Windows Administrator Area | Skype:[email protected] -
Cisco ASA 5520s in Cluster Outside interface stops sending traffic
Hi,
We are running a Pair of ASA 5520s in active/standby mode. In the last couple days the active device will just stop communicating on the outside interface. Because the rest of the interfaces are still up, it will not fail over, so we have to fail it manually. The secondary unit works and passes traffic correctly. We then reboot the Primary.
Then after some undetermined time, it happens again and we have to manually fail it the other way, reboot the affected ASA and wait for it to happen again.
We have a case with TAC but they have not been able to figure this one out. Has anyone else seen this behavior?
This is the version info:
Cisco Adaptive Security Appliance Software Version 8.4(7)
Device Manager Version 7.3(1)100
ThanksHi,
There are various possibilities on the ASA device which might be causing this issue:-
1) Block depletion
2) Memory depletion
Other things might be related to the external ISP as well.
Can we collect some outputs from the ASA device at the time when the issue is seen on the ASA device.
If you can share the output , i can have a look at it otherwise you can open a TAC case.
Thanks and Regards,
Vibhor Amrodia -
Having issues on ASA 5510 pass traffic between interfaces
I am trying to pass traffic between two internal interfaces but am unable to. Been searching quite a bit and have tried several things to no avail. I feel like there is a simple solution here I am just not seeing. Here is the relevant portion of my config:
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.5.1 255.255.255.0
interface Ethernet0/2
nameif ct-users
security-level 100
ip address 10.12.0.1 255.255.0.0
same-security-traffic permit inter-interface
access-list inside_nat0_outbound extended permit ip any 192.168.5.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 10.12.0.0 255.255.0.0
access-list inside_access_in extended permit ip any any
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (ct-users) 0 access-list inside_nat0_outbound
nat (ct-users) 1 0.0.0.0 0.0.0.0
static (inside,ct-users) 192.168.5.0 192.168.5.0 netmask 255.255.255.0
static (ct-users,inside) 10.12.0.0 10.12.0.0 netmask 255.255.0.0
access-group outside_access_in in interface outside
access-group outside_access_ipv6_in in interface outside
access-group inside_access_in in interface inside
access-group inside_access_ipv6_in in interface inside
access-group inside_access_in in interface ct-users
access-group inside_access_ipv6_in in interface ct-users
On both networks I am able to access the internet, just not traffic between each other.
A packet-tracer reveals the following (it's hitting some weird rules on the way):
cybertron# packet-tracer input inside tcp 192.168.5.2 ssh 10.12.0.2 ssh detailed
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xab827020, priority=1, domain=permit, deny=false
hits=8628156090, user_data=0x0, cs_id=0x0, l3_type=0x8
src mac=0000.0000.0000, mask=0000.0000.0000
dst mac=0000.0000.0000, mask=0100.0000.0000
Phase: 2
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
static (ct-users,inside) 10.12.0.0 10.12.0.0 netmask 255.255.0.0
match ip ct-users 10.12.0.0 255.255.0.0 inside any
static translation to 10.12.0.0
translate_hits = 0, untranslate_hits = 6
Additional Information:
NAT divert to egress interface ct-users
Untranslate 10.12.0.0/0 to 10.12.0.0/0 using netmask 255.255.0.0
Phase: 3
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group inside_access_in in interface inside
access-list inside_access_in extended permit ip any any
Additional Information:
Forward Flow based lookup yields rule:
in id=0xad5bec88, priority=12, domain=permit, deny=false
hits=173081, user_data=0xa8a76ac0, cs_id=0x0, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xab829758, priority=0, domain=inspect-ip-options, deny=true
hits=146139764, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 5
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xad48c860, priority=6, domain=nat-exempt-reverse, deny=false
hits=2, user_data=0xad4b5e98, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
src ip=192.168.5.0, mask=255.255.255.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 6
Type: NAT-EXEMPT
Subtype:
Result: ALLOW
Config:
match ip inside any ct-users 10.12.0.0 255.255.0.0
NAT exempt
translate_hits = 2, untranslate_hits = 2
Additional Information:
Forward Flow based lookup yields rule:
in id=0xad3b1f70, priority=6, domain=nat-exempt, deny=false
hits=2, user_data=0xad62b7a8, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=10.12.0.0, mask=255.255.0.0, port=0, dscp=0x0
Phase: 7
Type: NAT
Subtype:
Result: ALLOW
Config:
static (inside,ct-users) 192.168.5.0 192.168.5.0 netmask 255.255.255.0
match ip inside 192.168.5.0 255.255.255.0 ct-users any
static translation to 192.168.5.0
translate_hits = 1, untranslate_hits = 15
Additional Information:
Forward Flow based lookup yields rule:
in id=0xadf7a778, priority=5, domain=nat, deny=false
hits=6, user_data=0xad80cfd0, cs_id=0x0, flags=0x0, protocol=0
src ip=192.168.5.0, mask=255.255.255.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 8
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (inside,outside) udp 184.73.2.1 1514 192.168.5.2 1514 netmask 255.255.255.255
match udp inside host 192.168.5.2 eq 1514 outside any
static translation to 184.73.2.1/1514
translate_hits = 0, untranslate_hits = 0
Additional Information:
Forward Flow based lookup yields rule:
in id=0xab8e2928, priority=5, domain=host, deny=false
hits=9276881, user_data=0xab8e1d20, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=192.168.5.2, mask=255.255.255.255, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 9
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
static (ct-users,inside) 10.12.0.0 10.12.0.0 netmask 255.255.0.0
match ip ct-users 10.12.0.0 255.255.0.0 inside any
static translation to 10.12.0.0
translate_hits = 0, untranslate_hits = 6
Additional Information:
Forward Flow based lookup yields rule:
out id=0xad158dc0, priority=5, domain=nat-reverse, deny=false
hits=6, user_data=0xac0fb6b8, cs_id=0x0, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=10.12.0.0, mask=255.255.0.0, port=0, dscp=0x0
Phase: 10
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (ct-users,inside) 10.12.0.0 10.12.0.0 netmask 255.255.0.0
match ip ct-users 10.12.0.0 255.255.0.0 inside any
static translation to 10.12.0.0
translate_hits = 0, untranslate_hits = 6
Additional Information:
Reverse Flow based lookup yields rule:
in id=0xada0cd38, priority=5, domain=host, deny=false
hits=131, user_data=0xac0fb6b8, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=10.12.0.0, mask=255.255.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 11
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Reverse Flow based lookup yields rule:
in id=0xad5c1ab0, priority=0, domain=inspect-ip-options, deny=true
hits=130, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 12
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 189385494, packet dispatched to next module
Module information for forward flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_tcp_normalizer
snp_fp_translate
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Module information for reverse flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_tcp_normalizer
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: ct-users
output-status: up
output-line-status: up
Action: allowhow are you testing? if you are pinging between the subnets, make sure you have disabled windows firewall and/or any other firewall that is installed on the PCs (remember to re-enable it later).
Are the NAT commands there because you were trying different things to get this working? I suggest you use the command no nat-control instead. Depending on the version of ASA you are running it may already be disabled by default. In version 8.4 and later nat-control has been removed completely.
Please remember to select a correct answer and rate helpful posts -
Cisco ASA 5505 Routing between internal networks
Hi,
I am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside
2. DMZ
3. ServerNet1
4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it.
Here is the running conf:
interface Ethernet0/0
switchport access vlan 20
interface Ethernet0/1
switchport access vlan 20
interface Ethernet0/2
switchport access vlan 19
interface Ethernet0/3
switchport access vlan 10
switchport trunk allowed vlan 10,19-20
switchport trunk native vlan 1
interface Ethernet0/4
switchport access vlan 10
interface Ethernet0/5
switchport access vlan 10
switchport trunk allowed vlan 10-11,19-20
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/6
switchport access vlan 10
switchport trunk allowed vlan 10-11,19-20
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/7
switchport access vlan 10
interface Vlan10
nameif inside
security-level 90
ip address 192.168.2.1 255.255.255.0
interface Vlan11
nameif ServerNet1
security-level 100
ip address 192.168.4.1 255.255.255.0
interface Vlan19
nameif DMZ
security-level 10
ip address 192.168.3.1 255.255.255.0
interface Vlan20
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network DNS
host 192.168.2.10
description DNS Liikenne
object network Srv2
host 192.168.2.10
description DC, DNS, DNCP
object network obj-192.168.4.0
subnet 192.168.4.0 255.255.255.0
object network ServerNet1
subnet 192.168.4.0 255.255.255.0
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group network RFC1918
object-group network InternalNetworks
network-object 192.168.2.0 255.255.255.0
network-object 192.168.3.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq domain
service-object udp destination eq domain
service-object udp destination eq nameserver
service-object udp destination eq ntp
object-group service DM_INLINE_TCP_1 tcp
port-object eq www
port-object eq https
port-object eq ftp
port-object eq ftp-data
object-group service rdp tcp-udp
description Microsoft RDP
port-object eq 3389
object-group service DM_INLINE_TCP_2 tcp
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
object-group service DM_INLINE_SERVICE_2
service-object tcp destination eq domain
service-object udp destination eq domain
object-group network DM_INLINE_NETWORK_1
network-object object obj-192.168.2.0
network-object object obj-192.168.4.0
access-list dmz_access_in extended permit ip object obj-192.168.3.0 object obj_any
access-list dmz_access_in extended deny ip any object-group InternalNetworks
access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object DNS eq domain
access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object-group DM_INLINE_NETWORK_1 object-group rdp
access-list DMZ_access_in extended deny ip any object-group InternalNetworks
access-list DMZ_access_in extended permit tcp object obj-192.168.3.0 object obj_any object-group DM_INLINE_TCP_2
access-list inside_access_in extended permit ip object obj-192.168.2.0 object-group InternalNetworks
access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj_any object-group rdp
access-list inside_access_in extended permit tcp object obj-192.168.2.0 object obj_any object-group DM_INLINE_TCP_1
access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Srv2 object obj_any
access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj-192.168.3.0 object-group rdp
access-list ServerNet1_access_in extended permit object-group DM_INLINE_SERVICE_2 any object DNS
access-list ServerNet1_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu ServerNet1 1500
mtu inside 1500
mtu DMZ 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711-52.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,DMZ) source static obj-192.168.2.0 obj-192.168.2.0 destination static obj-192.168.2.0 obj-192.168.2.0 no-proxy-arp
object network obj_any
nat (inside,outside) dynamic interface
nat (DMZ,outside) after-auto source dynamic obj_any interface destination static obj_any obj_any
nat (ServerNet1,outside) after-auto source dynamic obj-192.168.4.0 interface
access-group ServerNet1_access_in in interface ServerNet1
access-group inside_access_in in interface inside
access-group DMZ_access_in in interface DMZ
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.4.0 255.255.255.0 ServerNet1
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh 192.168.4.0 255.255.255.0 ServerNet1
ssh 192.168.2.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymousHi Jouni,
Yep, Finnish would be good also =)
In front of ASA is DSL modem, on the trunk ports is Hyper-V host that uses the trunk ports so that every VM has their VLAN ID defined in the VM level. Everything is working good on that end. Also there is WLAN Access Pois on one of the ASA ports, on the WLAN AP there is the management portal address on DMZ that i have been testing agains (192.168.3.4)
If i configure Dynamic PAT from inside to the DMZ then the traffic starts to work from inside to all hosts on DMZ but thats not the right way to do it so no shortcuts =)
Here is the conf now, still doesnt work:
interface Ethernet0/0
switchport access vlan 20
interface Ethernet0/1
switchport access vlan 20
interface Ethernet0/2
switchport access vlan 19
interface Ethernet0/3
switchport access vlan 10
switchport trunk allowed vlan 10,19-20
switchport trunk native vlan 1
interface Ethernet0/4
switchport access vlan 10
interface Ethernet0/5
switchport access vlan 10
switchport trunk allowed vlan 10-11,19-20
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/6
switchport access vlan 10
switchport trunk allowed vlan 10-11,19-20
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/7
switchport access vlan 10
interface Vlan10
nameif inside
security-level 90
ip address 192.168.2.1 255.255.255.0
interface Vlan11
nameif ServerNet1
security-level 100
ip address 192.168.4.1 255.255.255.0
interface Vlan19
nameif DMZ
security-level 10
ip address 192.168.3.1 255.255.255.0
interface Vlan20
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network DNS
host 192.168.2.10
description DNS Liikenne
object network Srv2
host 192.168.2.10
description DC, DNS, DNCP
object network obj-192.168.4.0
subnet 192.168.4.0 255.255.255.0
object network ServerNet1
subnet 192.168.4.0 255.255.255.0
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group network RFC1918
object-group network InternalNetworks
network-object 192.168.2.0 255.255.255.0
network-object 192.168.3.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq domain
service-object udp destination eq domain
service-object udp destination eq nameserver
service-object udp destination eq ntp
object-group service DM_INLINE_TCP_1 tcp
port-object eq www
port-object eq https
port-object eq ftp
port-object eq ftp-data
object-group service rdp tcp-udp
description Microsoft RDP
port-object eq 3389
object-group service DM_INLINE_TCP_2 tcp
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
object-group service DM_INLINE_SERVICE_2
service-object tcp destination eq domain
service-object udp destination eq domain
object-group network DM_INLINE_NETWORK_1
network-object object obj-192.168.2.0
network-object object obj-192.168.4.0
object-group network DEFAULT-PAT-SOURCE
description Default PAT source networks
network-object 192.168.2.0 255.255.255.0
network-object 192.168.3.0 255.255.255.0
network-object 192.168.4.0 255.255.255.0
access-list dmz_access_in extended permit ip object obj-192.168.3.0 object obj_any
access-list dmz_access_in extended deny ip any object-group InternalNetworks
access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object DNS eq domain
access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object-group DM_INLINE_NETWORK_1 object-group rdp
access-list DMZ_access_in extended deny ip any object-group InternalNetworks
access-list DMZ_access_in extended permit tcp object obj-192.168.3.0 object obj_any object-group DM_INLINE_TCP_2
access-list inside_access_in extended permit ip object obj-192.168.2.0 object-group InternalNetworks
access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj_any object-group rdp
access-list inside_access_in extended permit tcp object obj-192.168.2.0 object obj_any object-group DM_INLINE_TCP_1
access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Srv2 object obj_any
access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj-192.168.3.0 object-group rdp
access-list ServerNet1_access_in extended permit object-group DM_INLINE_SERVICE_2 any object DNS
access-list ServerNet1_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu ServerNet1 1500
mtu inside 1500
mtu DMZ 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711-52.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (any,outside) after-auto source dynamic DEFAULT-PAT-SOURCE interface
access-group ServerNet1_access_in in interface ServerNet1
access-group inside_access_in in interface inside
access-group DMZ_access_in in interface DMZ
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.4.0 255.255.255.0 ServerNet1
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh 192.168.4.0 255.255.255.0 ServerNet1
ssh 192.168.2.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous -
Cisco ASA 5520 (asa 8.2) hairpinning
Hi All,
We have a ASA 5520 (redundant) in our network which we are using for different customers. For every new customer we create a new VLAN and place their servers in this VLAN. On the ASA we create a new subinterface for every customer which is connected to the corresponding VLAN.
Most customers get a private ip-range (e.g. 192.168.x.x/24) on which they should configure their servers. Because most customers don't need to be to access eachothers server all VLAN interfaces have the same security-level of 50. I haven't enable the "same-security-traffic permit inter-interface" option, so traffic between those interfaces is blocked, as expected.
Some customers (e.g. customer A) need public webmail of smtp access to there servers. So we use both NAT and PAT to make that happen.
So, recently we've got a customer (customer B) who placed their webservers behind our ASA. Because we didn't want to use NAT statements all the time, we dediced to configure a public /29 subnet on their VLAN. Because the website on this customer's servers need to be visible for everybody, we've lowered the security-level of this VLAN interface to 40 (instead of 50) and applied some ACL's. So other customers (e.g. customer A) are also able to reach the websites of customer B. So everything is just working fine.
Now, customer A decided that they want to run their website on their own servers as well. So, I created a static PAT for TCP 80. So the website is accessible from the outside world. But.....customer B is not able to reach customer A's website on the translated address. So, I've created a second PAT (using the same public address) but this time to customer B's interface. But still, we're not able to reach customer A's website.
I've also enabled the "same-security-traffic permit intra-interface", but still the website is unreachable to customer B.
Here's a small drawing of the situation:
The ip-addresses are, of course, not real.
Can anybody place help me with this issue?That's a very cool command that I didn't know about.
I see that the packet is drop at phase 7 (NAT-EXEMPT).
Phase: 7
Type: NAT-EXEMPT
Subtype: rpf-check
Result: DROP
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x74455b60, priority=6, domain=nat-exempt-reverse, deny=false
hits=61, user_data=0x744558f0, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
src ip=Cust_B_LAN, mask=255.255.255.240, port=0
dst ip=Cust_A_LAN, mask=255.255.255.0, port=0, dscp=0x0
Result:
input-interface: Cust_B
input-status: up
input-line-status: up
output-interface: Cust_A
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
I seemed that I had a nonat rule messing the communication between these interfaces. After removing it, the traffic was flowing just fine.
Thanks for your support.
Ron -
Cisco ASA QoS traffic policing - how to count conform burst
hi,
I have cisco ASA 8.4(5). I will do configuration for QoS traffic policing. Maximum output/input rate will be 850 Mbits/s.
I am not sure if I need to do configuration also for conform burst ? if yes, can I count suitable value for it ? I must admit that I dont understand difference between conform rate and conform burst.
access-list acl_qos_policing_admin extended permit ip any any
class-map class_qos_policing_admin
match access-list acl_qos_policing_admin
policy-map policy_qos_policing_admin
class class_qos_policing_admin
police output 850000000 xxxxxxx
police input 850000000 xxxxxxx
service-policy policy_qos_policing_admin interface
inside_ADMHi, I already have done configuration on production firewall. Bandwidth test worked very good for 200Mbps or 300 Mbps. But I got little strange results for bigger rate limits such 600Mbps or 850 Mbps. I could not see any dropped packets. I did test via http://www.speedtest.net. Maybe because
I need to set conform-burst? there is now only default value (If you set bigger conform-rate then you get bigger conform-burst with default value).
Interface inside_EDU:
Service-policy: policy_qos_policing_edu
Class-map: class_qos_policing_edu
Output police Interface inside_EDU:
cir 200000000 bps, bc 6250000 bytes
Input police Interface inside_EDU:
cir 200000000 bps, bc 6250000 bytes
Interface inside_EDU:
Service-policy: policy_qos_policing_edu
Class-map: class_qos_policing_edu
Output police Interface inside_EDU:
cir 600000000 bps, bc 18750000 bytes
Input police Interface inside_EDU:
cir 600000000 bps, bc 18750000 bytes
Interface inside_ADM:
Service-policy: policy_qos_policing_admin
Class-map: class_qos_policing_admin
Output police Interface inside_ADM:
cir 300000000 bps, bc 9375000 bytes
Input police Interface inside_ADM:
cir 300000000 bps, bc 9375000 bytes
Interface inside_ADM:
Service-policy: policy_qos_policing_admin
Class-map: class_qos_policing_admin
Output police Interface inside_ADM:
cir 850000000 bps, bc 26562500 bytes
Input police Interface inside_ADM:
cir 850000000 bps, bc 26562500 bytes
Maybe you are looking for
-
How can I pass a path to the FileReference upload function?
i don't understand how can i upload a file from the browse function after you've selected a file. since FileReference.name returns only the filename w/extension and not the path, how can i work around this? i understand the security implications with
-
Problem with rotate function.
I got a problem with the rotate function. When I rotate an (text) object (point text but same behavior with area text) on the GUI of Illustrator, the resize bounds around (see screenshot) is rotated as well so that you can resize it as used to. If I
-
i have downloaded pages 5 and installed and have been using it. when i turned my computer on today and tried to open a document, it was not there! How do i find pages 5?
-
I am using ajax to display a region from another page. This region has 2 text fields and a button that when pressed branches to another page. When I input the data and click the button I get an error: Error Item ID (10060522396890067) is not an item
-
Hi experts, I am trying to import data in a delimited text, error while connecting is "Unable to Connect to Source". Please advise.